STANDARD BIDDING DOCUMENT

Procurement of Goods
Sealed Quotation

[For Procurement of Goods between NRs.0.5 Million to NRs. 2.00

Million and for Health equipment and drugs between NRs.0.5 Million
to NRs.5.00 Million]

Issued by:
Government of Nepal
Public Procurement Monitoring Office
Tahachal, Kathmandu

January 2018
(First Revision May,2019)
 Table of Contents

Introduction and Instructions ..............................................................................................

Section I. Invitation for Sealed Quotation ..........................................................................
Section II. Instructions to Bidders .....................................................................................
Section III. Bid data shhet ...................................................................................................
Section IV. Quotation form and price Schedule ................................................................
Section V. Schedule of requirements .................................................................................
Section VI. General Conditions of contract ........................................................................
Section VII.Special Conditions of contract ........................................................................
Section VIII.Contract form .................................................................................................
Introduction and Instructions
Introduction

1. This Standard Bidding Documents has been prepared by Government of Nepal (GON), Public
Procurement Monitoring Office (PPMO) for use in the procurement of Goods (value upto NRs.2.00
million/ for Health equipment and drugs upto NRs.5.00 Million through Sealed Quotation.
2. This Introduction and Instruction part of the SBD should not be incorporated into the bidding documents
of Public Entities (PEs) that may be issued to the Supplier as a part of bid documents. This part is only
for the use of Purchaser in order to prepare a proper bidding document.
3. If any provision of this document is inconsistent with Public Procurement Act (PPA). 2063 or Public
Procurement Regulations (PPR), 2064, the provision of this document shall be void to the extent of
such inconsistency and the provision of PPA and PPR shall prevail.
 Abbreviations
BD ........................ Bidding Document
BDF……………... Bidding Forms
BDS...................... Bid Data Sheet
BOQ ……………..Bill of Quantities
COF …………….. Contract Forms
DP ………………. Development Partners
DoLIDAR ………. Department of Local Infrastructure Development and Agricultural Roads
ELI ………………. Eligibility
EQC ..................... Evaluation and Qualification Criteria
EXP ……………… Experience
FIN ………………. Financial
GCC ..................... General Conditions of Contract
GoN ..................... Government of Nepal
ICB ...................... International Competitive Bidding
ICC....................... International Chamber of Commerce
ITB ....................... Instructions to Bidders
JV ………………..Joint Venture
LIT ……………….. Litigation
NCB ……………... National Competitive Bidding
PAN ……………… Permanent Account Number
PPA …………….. Public Procurement Act
PPMO …………… Public Procurement Monitoring Office
PPR ……………... Public Procurement Regulations
PL ......................... Profit and Loss
SBD...................... Standard Bidding Document
SCC …………….. Special Conditions of Contract
TS......................... Technical Specifications
VAT ……………… Value Added Tax
WRQ …………….. Works Requirements
 Section - I
Invitation for Sealed Quotation
 Invitation for Sealed Quotation

Name of the Office: Ripumardini Sainik Secondary School

Address of the Office: Ripumardini Sainik Secondary School

Bansbari
Kathmandu, Kathmandu
Nepal
Invitation for Sealed Quotation for the procurement of

Sealed Quotation No: NA/RSSS/SQ/076/77/02

Date of first Publication: 09-02-2020

1. The Ripumardini Sainik Secondary School invites sealed quotations from registered Suppliers for the Supply of Various Office
Equipment's .
2. Eligible eligible Suppliers may obtain further information and inspect the Sealed quotation Forms at the office of Ripumardini
Sainik Secondary School
Bansbari
Kathmandu, Kathmandu
Nepal, 01-4374335, , [email protected].
OR
[may visit PPMO website www.bolpatra.gov.np.]
3. If hard copy is allowed then a complete then a complete set of Bidding Documents may be purchased from the office Ripumardini
Sainik Secondary School Ripumardini Sainik Secondary School
Bansbari
Kathmandu, Kathmandu
Nepal and the officeRipumardini Sainik Secondary School Ripumardini Sainik Secondary School
Bansbari
Kathmandu, Kathmandu
Nepalby eligible Bidders on the submission of a written application, along with the copy of company/firm registration certificate,
and upon payment of a non-refundable fee of NRs.1000.0 till 24-02-2020 12:00 during office hours.
4. Bidder who chooses to submit their bid electronically may download the bidding documents for e-submission from PPMO’s e-GP
i.e www.bopatra.gov.np/egp. Bidders, submitting their bid electronically, should deposit the cost of bidding document in the
following account
i. Name of the Bank :NIC Asia Bank Ltd. ii. Name of Office :Ripumardini Sainik Secondary School
iii. Office Code no : iv. Office Account No :1341066776524002
v. Rajaswa (revenue) Shirshak No :
5. Sealed bids must be submitted to the office Ripumardini Sainik Secondary School Ripumardini Sainik Secondary School
Bansbari
Kathmandu, Kathmandu
Nepal by hand or through e-GP system i.e www.bopatra.gov.np/egp on or before 24-02-2020 12:00. Bids received after this
deadline will be rejected.
6. The bids will be opened in the presence of Bidders' representatives who choose to attend at 24-02-2020 13:00 at the office of
Ripumardini Sainik Secondary School
Bansbari
Kathmandu, Kathmandu
Nepal.
Bids must be valid for a period of 45 days after bid opening and must be accompanied by a bid security amounting to a minimum
of 51000 , which shall be valid for 30 days beyond the validity period of the bid (i.e. [Refer Clause ITB 20.1]). If bidder wishes to
submit the Cash Security, the cash should be deposited in Deposit Account No.[1341066776524002] at [NIC Asia Bank Ltd. ,
Kathmandu, 0, Kathmandu, Kathmandu] and submit the receipt of the deposited amount of cash along with the Sealed Quotation.
7. If the last date of purchasing and /or submission falls on a government holiday, then the next working day shall be considered as
the last date. In such case the validity period of the bid security shall remain the same as specified for the original last date of bid
submission
8. The Purchaser reserves the right to accept or reject, wholly or partly any or all the Sealed Quotations without assigning any
reason, whatsoever.
 Section - II

Instructions to Bidders

Notes on the Instructions to Bidders

This section of the bidding documents should provide the information necessary for
Interested Suppliers to prepare responsive bids, in accordance with the requirements of
the Purchaser. It should also give information on bid submission, opening and
evaluation, and award of Contract.These Instructions to Bidders shall not be part of the
Contract and shall cease to have effect once the Contract is signed.
 Section II. Instructions to Bidder

1. Scope of Works 1.1 The Purchaser stated in the BDS for the procurement of Goods as
detailed in attached specifications, drawings and the bill of quantities
provided herein. The name of Purchaser, name of project and contract
identification number of Contracts are provided in the BDS.

2. Eligible Bidder

2.1 This Invitation for Bids is open to all registered Suppliers with eligibility
criteria specified below.
a) Up to date Firm/Company Registration Certificate
b) VAT and PAN Registration Certificates
c) Tax Clearance Certificate for the Fiscal Year …………….
d) Business registration certificate ( if required)
e) Power of Attorney to sign the Sealed Quotation
f) JV Agreement, or a letter of intent to enter into JV, signed by all
legally authorized signatories of all the parties to the existing or
intended JV, in case of Sealed Quotation is submitted from JV.
g) Other documents as needed [Please specify]

2.2 A bidder declared blacklisted and ineligible by the GoN, Public

Procurement Monitoring Office (PPMO) and/or the DP in case of DP
funded project, shall be ineligible to bid for a contract during the period of
time determined by the GoN, PPMO and/or the DP.

2.3 Firms shall be excluded in any of the cases, if the corruption case is being
filed to Court against the Natural Person or Board of Director of the
firm/institution /company or any partner of JV, such Natural Person or
Board of Director of the firm/institution /company or any partner of JV shall
not be eligible to participate in procurement process till the concerned
Court has not issued the decision of clearance against the Corruption
Charges.

3. One Quotation per 3.1 Each Bidder shall submit only one quotation, A Bidder who submits more
Bidder than one quotation shall cause all the quotations with the Bidder’s
participation to be disqualified.

4. Cost of Bidding 4.1 The Bidder shall bear all costs associated with the preparation and
submission of his Quotation and the Purchaser shall in no case be liable
for those costs.
5. Site Visit 5.1 The Bidder at his own cost, responsibility and risk may visit the site of the
supply, delivery or installation of Goods and acquire all necessary
information for preparing the bid and entering into a contract for the
procurement of Goods.

6. Content of 6.1 The Quotation Form comprise the documents listed below:
Quotation
Form 1. Section I: Invitation for Sealed Quotation (SQ)
2. Section II: Instructions to Bidders
3. Section III: Bid Data Sheet
4. Section IV Quotation Forms and Price Schedule
5. Section V: Schedule of Requirements
6. Section VI: General Conditions of Contract (GCC)
7. Section VII: Special Conditions of Contract
8. Section VIII: Contract Form

7. Clarification 7.1 A prospective Supplier/Bidder may obtain clarification on the Quotation

Form from the Purchaser on or before 5 days prior to the deadline for
submission of Quotation.

8. Language of 8.1 All documents relating to the Quotation shall be in English or in Nepali.
Quotation

9. Documents 9.1 The Quotation by the Bidder shall comprise the following:
Comprising a. Quotation Form and Price Schedules
Quotation
b. Bid Security
c. Schedule of Requirements

10. Quotation Prices 10.1 The Bidder shall indicate on the appropriate Price Schedule the unit
prices (where applicable) and total price in Nepali Rupees. for all items
of the goods to be supplied under the contract.
10.2 All duties, taxes and other levies payable by the Bidder under the
contract shall be included in the rates, prices and total Bid Price
submitted by the Bidder.
10.3 Price quoted by the Bidder shall remain fixed and valid until completion
of the Contract Performance and will not be subject to variation in any
account.
11. Quotation Validity 11.1 The Sealed Quotation shall remain valid for the period of 45 days after
opening of the quotation. A bid valid for a shorter period shall be
rejected by the Purchaser as nonresponsive.

12. Quotation/Bid 12.1 The Bidder shall furnish as part of its Sealed Quotation, in original form,
Security a bid security as specified in the BDS. In case of e-submission of
Quotation, the Bidder shall upload scanned copy of Bid security letter at
the time of electronic submission of the Sealed Quotation. The Bidder
 accepts that the scanned copy of the Bid security shall, for all purposes,
be equal to the original. The details of original Bid Security and the
scanned copy submitted with e-Sealed Quotation should be the same
otherwise the Sealed Quotation shall be non-responsive.

12.2 The Bid Security shall be, at the Bidder’s option, in any of the following
forms:
(a) an unconditional bank guarantee from Commercial Bank or
Financial Institution eligible to issue Bank Guarantee as per
prevailing Law or;
(b) a cash deposit voucher in the Purchaser's Account as specified
in the BDS
In the case of a bank guarantee, the Bid Security shall be submitted
either using the Bid Security Form included in Section III (Bidding
Forms) or in another Form acceptable to the Purchaser. The form
must include the complete name of the Bidder. The Bid security
shall be valid for minimum thirty (30) days beyond the original
validity period of the bid
12.3 Any Sealed Quotation not accompanied by an enforceable and
substantially compliant bid security, shall be rejected by the
Purchaser as nonresponsive. In case of e-Submission, if the scanned
copy of an acceptable Bid Security letter is not uploaded with the
electronic Bid then Bid shall be rejected.
12.4 The Bid security shall be forfeited if:
(a) a Bidder requests for withdrawal or modification during the
period of Quotation validity specified by the Bidder on the Letter
of Bid, after Sealed Quotation submission deadline.
(b) a Bidder changes the prices or substance of the Sealed Quotation
while providing information;
(c) a Bidder involves in fraud and corruption pursuant to clause 26;
(d) the successful Bidder fails to:
(i) furnish a performance security in accordance with clause 25;
(ii) sign the Contract in accordance within the period stipulated in
Letter of Award.; or
(iii) accept the correction of arithmetical errors pursuant to clause
19.1
(iv) fails to provide the clarification of its Quotation by the date
and time set in the Purchaser's request for clarification

13. Format and 13.1 The Quotation shall be typed or written in indelible ink and shall be
Signing of signed by an authorized person. Any entries or amendments including
Quotations alternations, additions or corrections made shall be initialled by the
same authorized person.
14. Sealing and 14.1 Bidders may submit their bids by manually or by electronically. When
Marking of so specified in the BDS. Procedures for submission, sealing and
Quotations
marking are as follows:
Bidders submitting bids by manually. The Bidder shall submit his bid
in sealed envelopes. The envelope shall be addressed to the
Purchaser as specified in the BDS and shall bear the name and
identification number of the Sealed quotation.
14.2 Bidders submitting Bids electronically shall follow the electronic bid
submission procedure specified in the BDS

15. Deadline for 15.1 Quotations shall be delivered to the Purchaser at the address no later
Submission of than the time and date specified in the BDS.
Quotations

16. Late Quotation 16.1 Any Quotation received by the Purchaser after the deadline shall not be
accepted and shall be returned unopened to the Bidder upon request.

17. Modification 17.1 Sealed Quotations once submitted shall not be withdrawn or modified.
And
Withdrawal

18. Bid Opening 18.1 The Purchaser shall open the Quotations in the presence of the Bidders'
representatives who choose to attend at the time and in the place as
specified in the BDS
18.2 The Purchaser shall prepare and provide minutes of the opening
including the information disclosed to those present.

19. Process to be 19.1 Information relating to the examination, evaluation and comparison of
Confidential Quotations and recommendations for the award of a contract shall not
be disclosed to Bidders or any other persons not officially concerned
with such process until the award to the successful Bidder has been
announced. Any efforts by the Bidder to influence the Purchaser in the
Quotation evaluation, comparison or contract award decisions may
result in rejection of Bidder’s quotation.
20. Examination 20.1 Prior to the detailed evaluation of Quotations, the Purchaser shall
of Quotations determine whether each Quotation
(a) meets the eligibility criteria defined in Clause 2;
(b) has been properly signed by the authorized person;
(c) is accompanied by the required securities; and
(d) is substantially responsive to the requirements of the Bidding
documents.
21. Evaluation and 21.1 In evaluating the Quotations, the Purchaser shall determine for each
Comparison of Sealed Quotation the evaluated Quotation Price by adjusting any
Quotations
corrections for errors. Quotations shall be checked by the Purchaser
for any arithmetic errors. Errors shall be corrected by the Purchaser as
follows:
(a) only for unit price Contracts, if there is a discrepancy between the
unit price and the total price that is obtained by multiplying the
unit price and quantity, the unit price shall prevail and the total
price shall be corrected, unless in the opinion of the Purchaser
there is an obvious misplacement of the decimal point in the unit
price, in which case the total price as quoted shall govern and the
unit price shall be corrected;
(b) if there is an error in a total corresponding to the addition or
subtraction of subtotals, the subtotals shall prevail and the total
shall be corrected; and
(c) If there is a discrepancy between the Quotation price in the
Summary of Price Schedule and the Quotation amount in item (c)
of the Letter of Quotation, the price in the Summary of Price
Schedule will prevail and the Quotation amount in item (c) of the
Letter of Quotation will be corrected.
(d) if there is a discrepancy between words and figures, the amount
in words shall prevail, unless the amount expressed in words is
related to an arithmetic error, in which case the amount in figures
shall prevail subject to (a) ,(b) and (c) above.
21.2 In case of e-submission of bid, upon notification from the Purchaser,
the bidder shall also submit the original of documents comprising the
Sealed Quotation as per ITB 9 for verification of submitted documents
for acceptance of the e-submitted bid. If a Bidder does not provide
original of document of its Sealed Quotation by the date and time set in
the Purchaser's request for clarification, its bid may be rejected.
21.3 If the Bidder that submitted the lowest evaluated bid does not accept the
correction of errors, its bid shall be disqualified and its Quotation security
shall be forfeited.
21.4 If the corruption case is being filed to Court against the Natural Person
or Board of Director of the firm/institution /company or any partner of JV,
such Natural Person or Board of Director of the firm/institution /company
or any partner of JV such bidder’s bid shall be excluded during the
evaluation.
22. Award of
Contract 22.1 The Purchaser shall decide the award of the contract to the Bidder
whose Quotation is within the approved estimate and who has offered
the lowest evaluated Price within Quotation validity period provided
that such Bidder has been determined to be eligible in accordance with
the provisions of Clauses 2.
22.2 If the corruption case is being filed to Court against the Natural Person
or Board of Director of the firm/institution /company or any partner of

JV, such Natural Person or Board of Director of the firm/institution

/company or any partner of JV such bidder’s bid shall be rejected.

23. Purchaser's 23.1 The Purchaser reserves the right to accept or reject any Quotation or to
Right to Accept cancel the bidding process and reject all Quotations, at any time prior to
or Reject the award of the contract, without assigning any reasons whatsoever
and without thereby incurring any liability to the affected Bidder or
Bidders.

24. Notification of 24.1The Bidder whose bid is accepted and all other participating bidders shall
Award and be notified of the award by the Purchaser.
Signing of
Agreement 24.2 The notification (hereafter called the “Letter of Acceptance”) to the
successful Bidder shall state the sum that the Purchaser shall pay the
Bidder in the execution and completion of the contract. Within 7 days
of receipt of the Letter of Acceptance, the successful Bidder shall
deliver the Performance Security pursuant Clause 25 and sign the
Agreement.
24.3 Inability of the Bidder to make an Agreement within the above stated
period shall result in the forfeiture of the Bidder’s Quotation Security
and , upon which the Contract shall then be awarded to the next
successive successful Bidder.
25. Performance 25.1 Within seven (7) days of the receipt of Letter of Acceptance from the
Security Purchaser, the successful Bidder shall furnish the performance
security as stated below from Commercial Bank or Financial Institution
eligible to issue Bank Guarantee as per prevailing Law in accordance
with the conditions of Contract using Sample Form for the Performance
Security included in Section VIII (Contract Forms), or another form
acceptable to the Purchaser.
i) If bid price of the bidder selected for acceptance is up to 15 (fifteen)
percent below the approved cost estimate, the performance security
amount shall be 5 (five) percent of the bid price.
ii) For the bid price of the bidder selected for acceptance is more than
15 (fifteen) percent below of the cost estimate, the performance
security amount shall be determined as follows:
Performance Security Amount =
[(0.85 x Cost Estimate – Bid Price) x 0.5] + 5% of Bid Price.
The Bid Price and Cost Estimate shall be inclusive of Value Added
Tax.

26. Corrupt or
Fraudulent 26.1 The Purchaser shall reject a bid for award if it determines that the
Practices Bidder recommended for award of contract has engaged in corrupt or
fraudulent practices in competing for the contract in question.
26.2 In case of a natural person or firm/institution/company which is

already declared blacklisted and ineligible by the GoN, any other new
or existing firm/institution/company owned partially or fully by such
Natural person or Owner or Board of director of blacklisted
firm/institution/company; shall not be eligible bidder.
27. Conduct of Bidders 27.1 The Bidder shall be responsible to fulfil his obligations as per the
requirement of the Contract Agreement, Bidding documents, GoN’s
Procurement Act and Regulations.
27.2 The Bidder shall not carry out or cause to carry out the following acts
with an intention to influence the implementation of the procurement
process or the procurement agreement :
a) give or propose improper inducement directly or indirectly,
b) distortion or misrepresentation of facts
c) engaging or being involved in corrupt or fraudulent practice
d) interference in participation of other prospective bidders.
e) coercion or threatening directly or indirectly to cause harm to the
person or the property of any person to be involved in the
procurement proceedings,
f) collusive practice among bidders before or after submission of
bids for distribution of works among bidders or fixing
artificial/uncompetitive bid price with an intention to deprive
the Purchaser the benefit of open competitive bid price..
27.3 contacting the Purchaser with an intention to influence the Purchaser
with regards to the bid or interference of any kind in examination and
evaluation of the bids during the period after opening of bids up to the
notification of award of contract

28. Blacklisting Bidder 28.1 Without prejudice to any other right of the Purchaser under this
Contract, GoN, Public Procurement Monitoring Office may blacklist a
bidder for his conduct up to three years on the following grounds and
seriousness of the act committed by the bidder:
a) if it is proved that the bidder committed acts pursuant to the Sub-
Clause 27.2,
b) if it is proved later that the bidder/Supplier had committed
substantial defect in implementation of the contract or had not
substantially fulfilled his obligations under the contract or the
completed work is not of the specified quality as per the contract
,
c) if convicted by a court of law in a criminal offence which
disqualifies the bidder from participating in the contract.
 d) if it is proved that the contract agreement signed by the bidder
was based on false or misrepresentation of bidder’s qualification
information,

e) Inability of the bidder signing the contract agreement, once the

letter of acceptance to the successful bidder has been provided
by the Purchaser.,
28.2 A firm declared blacklisted and ineligible by the GON shall be ineligible
to bid for a contract during the period of time determined by the
PPMO.

29. Publication of 29.1 Within three days of contract signing, the Public Entity shall
contract award publish a notice on the contract award with following
notice information: in its notice board as well as shall manage to
publish the notice on the notice board of District Coordination
Committee, District Administration Office, Provincial Treasury
and Controller Office and District Treasury and Controller
Office, Such notice shall also be posted in its website and
PPMO’s website.
a. Name of the procurement,
b. IFB number,
c. date and name of newspaper published the IFB notice,
d. Name of the successful Bidder, and the contract price.
29.2 The Purchaser shall promptly respond in writing to any
unsuccessful Bidder who, within thirty days from the date of
publication of contract award notice in accordance with ITB 29.1,
requests in writing the grounds on which its bid was not selected.

30. Provision of PPA 30.1 If any provision of this document are inconsistent with Public
and PPR Procurement Act (PPA), 2063 or Public Procurement Regulations (PPR),
2064, the provision of this documents shall be void to the extent of
such inconsistency and the provision of PPA and PPR shall prevail.
 Section III Bid Data Sheet

ITB 1 The scope of Supply is :

The number of the Invitation for Sealed Quotation (SQ) is :NA/RSSS/SQ/076/77/02The Purchaser is: Ripumardini Sainik
Secondary School
The Name of the Project is :Supply of Various Office Equipment's

ITB 10 The Bidder shall furnish a bid security, from Commercial Bank or Financial Institution eligible to issue Bank Guarantee
as per prevailing Law with a minimum of NRs.51000, which shall be valid for 30 days beyond the validity period of the
bid.

ITB 10(a) Cash Deposit Account for Bid Security:

Bank Name:NIC Asia Bank Ltd.
Bank Address:Kathmandu, 0, Kathmandu, Kathmandu
Account holder's Name:RSS
Account Number:1341066776524002

ITB 14.1 Bidders shall or shall not have the option of submitting their bids electronically. Bidders shall follow the electronic bid
submission procedures specified below:
i. The bidder is required to register in the e-GP system https://www.bolpatra.gov.np/egp following the procedure specified
in e-GP guideline.
ii. Interested bidders may either purchase the bidding document from the Purchaser's office as specified in the BDS or
may download the from e-GP system.
iii. The registered bidders need to maintain their profile data required during preparation of bids.
iv. In order to submit their bids electronically the cost of the bidding document shall be deposited in the account specified
in IFQ. In addition, electronic scanned copy (.pdf format) of the bank deposit voucher/cash receipt should also be
submitted along with the bid.
v. The bidder can prepare the their bids using data and documents maintained in bidder’s profile and forms/format
provided in Sealed Quotation Document by Purchaser. The bidder may submit bids as a single entity or as a joint venture.
The bidder submitting bid in joint venture shall have to upload joint venture agreement along with partner(s) Bolpatra ID
provided during bidder’s registration.
vi. Bidders (all partners in case of JV) should update their profile data and documents required during preparation and
submission of their bids.
vii. In case of bid submission in JV, the consent of the partners shall be obtained through the confirmation link sent to the
registered email address and the partners shall have to acknowledge their confirmation.The required forms and documents
shall be part of technical bids:
1. Letter of Quotation (Mandatory)
2.Quotation Security /Bank Guarantee (Mandatory)
3. Company registration (Mandatory)
4. VAT registration (Mandatory)
5. Tax clearances certificate or evidence of tax return submission for the F/Y (Mandatory)
6. Power of Attorney of Bid signatory (Mandatory)
7. Completed Price Schedule (Mandatory)
8. Bank Voucher for cost of bid document (Mandatory)
9. Joint venture agreement (Mandatory in case of JV Bid)
10. Additional documents specified in Bidding Document (any other required documents, which is not against the
provision of Procurement Act/Regulation/Directives and Standard Bidding Document issued by PPMO)

Note: The documents specified as “Mandatory” should be included in e-submission.

viii. After providing all the details and documents, bid response documents will be generated from the system. Bidders are
advised to download and verify the response documents prior to bid submission.
ix. For verifying the authentic user, the system will send one time password in the registered email address of the bidder.
System will validate the OTP and allow bidder to submit their bid.
x. Once Quotation is submitted, bidders won’t able to modify/withdrawal their bid.
xi. The Bidder/Quotation shall meet the following requirements and conditions for e-submission of bids:
a) The e-submitted Quotations must be readable through PDF reader.The facility for submission of Quotation
electronically through e-submission is to promote transparency, non-discrimination, equality of access, and open
competition in the bidding process. The Bidders are fully responsible to use the e- submission facility properly in e-GP
system as per specified procedures and in no case the Purchaser shall be held liable for Bidder's inability to use this
facility.b) When a bidder submits electronic bid through the PPMO e-GP portal, it is assumed that the bidder has prepared
the bid by studying and examining the complete set of the Bidding documents including specifications, drawings and
conditions of contract.

ITB 15 The deadline for Sealed Quotation submission is:24-02-2020 12:00

Address:Ripumardini Sainik Secondary School
Bansbari
Kathmandu, Kathmandu
Nepal
ITB 18 The Sealed Quotation opening shall take place at :
Address :Ripumardini Sainik Secondary School
Bansbari
Kathmandu, Kathmandu
Nepal
Date and Time:24-02-2020 13:00

a) e-GP system allows to download the Sealed Quotation response document only after bid opening date and time are met.
Simultaneous login of two members of the opening committee is required for bid opening.
b)The Purchaser shall conduct the opening of bid at the address on the same date and time as specified in bidding
document in the presence of Bidders’ representatives who choose to attend
 Section - IV
Sample Forms
 1. Quotation and Price Schedules
Date:

To: [name and address of the Purchaser]

Gentlemen and/or Ladies:

Having examined the Sealed Quotation (SQ) documents, we the undersigned, offer to supply and deliver [description
of goods and services] in conformity with the said SQ documents for the sum of [total SQ amount in words and figures]
or such other sums as may be ascertained in accordance with the Schedule of Prices attached herewith and made part of
this SQ.

We undertake, if our SQ is accepted, to deliver the goods in accordance with the delivery schedule specified in the
Schedule of Requirements.

If our SQ is accepted, we will obtain the guarantee of a bank in a sum equivalent to Five ( 5) percent of the Contract
Price for the due performance of the Contract, in the form prescribed by the Purchaser.

We agree to abide by this SQ for a Period of 45 days from the date fixed for SQ opening it shall remain binding upon us
and may be accepted at any time before the expiration of that period.

Until a formal Contract is prepared and executed, this SQ, together with your written acceptance thereof and your
notification of award, shall constitute a binding Contract between us.

We understand that you are not bound to accept the lowest or any SQ you may receive.

Dated this ______________________ day of ________________ 20______.

[signature] [in the capacity of]

Duly authorized to sign SQ for and on behalf of

 2. Bidder's Information Form

[The Bidder shall fill in this Form. No alterations to its format shall be permitted and no substitutions
shall be accepted. In case of joint venture, each partner shall fill the information in separate form.]

1. Bidder’s Legal Name

2 Bidder’s Address:

3 Bidder’s Country of Registration:

4 Bidder’s Year of Registration:

.

5 Bidder’s Legal Address in Country of

. Registration

6. Bidder’s Authorized Representative

Information:Name:
Address:

Telephone/Fax numbers:
Email Address:

7 Bidder’s Telephone/Fax numbers:

8 Bidder’s Email Address:

Attached are copies of the following original documents.

 1. Firm Registration Certificate

 2. Authorization to represent the firm

 3. Price Schedule for Goods

Name of Bidder _____________________ Contract Identification Number ___________

Unit Price1 EXW Total Price (in

Country of
Item Description Quantity NRs)
Origin (in NRs)
(cols. 4x5)
In Figure In Words
1 2 3 4 5 4x5=6

Total

VAT

Grand Total

Note: Unit price shall include all custom duties and taxes, transportation cost to the final destination and insurance cost.

[If there are more than one lot/slice/package, prepare Price Schedule form for each lot/slice/package]

Name

In the capacity of

Signed

Duly authorized to sign the Sealed Quotation for and on behalf of

Date:

1
The price shall include all customs duties and sales and other taxes already paid or payable on the components and raw
material used in the manufacture or assembly of the item or the customs duties and sales and other taxes paid on the
previously imported item offered ex warehouse, ex showroom, or off-the-shelf. These factors should not be entered
separately.
 4. Bid Security

Bank’s Name, and Address of Issuing Branch or Office

(On Letter head of the Commercial Bank or Financial Institution eligible to issue Bank Guarantee as per prevailing Law)

Beneficiary: .............................. name and address of Employer……………………………….

Date:………………...
Bid Security No.: .........................................................................

We have been informed that . …………. .[insert name of the Bidder] (hereinafter called “the Bidder”) intends
to submit its bid (hereinafter called “the Bid”) to you for the execution of …………... name of Contract .……………
under Invitation for Bids No. ……………… (“the IFB”).

Furthermore, we understand that, according to your conditions, bids must be supported by a bid guarantee.

At the request of the Bidder, we…………………. . name of Bank. ………………..hereby irrevocably undertake to pay
you any sum or sums not exceeding in total an amount of. . ………...amount in figures ………………………. (.
………….. .amount in words ……………….) upon receipt by us of your first demand in writing accompanied
by a written statement stating that the Bidder is in breach of its obligation(s) under the bid conditions, because
the Bidder:

(a) has withdrawn or modifies its Bid during the period of bid validity specified by the Bidder in the Form of Bid;
or
(b) does not accept the correction of errors in accordance with the Instructions to Bidders
(hereinafter “the ITB”); or
(c) having been notified of the acceptance of its Bid by the Employer during the period of bid validity, (i) fails
or refuses to execute the Contract Agreement, or (ii) fails or refuses to furnish the performance security,
in accordance with the ITB.
(d) is involved in fraud and corruption in accordance with the ITB

This guarantee will remain in force up to and including the date ………number…………days after the deadline
for submission of Bids as such deadline is stated in the instructions to Bidders or as it may be extended by the
Employer, notice of which extension(s) to the Bank is hereby waived. Any demand in respect of this guarantee
should reach the Bank not letter than the above date.
This Bank guarantee shall not be withdrawn or released merely upon return of the original guarantee by the
Bidder unless notified by you for the release of the guarantee.

This guarantee is subject to the Uniform Rules for Demand Guarantees, ICC Publication No. 758.

Bank’s seal and authorized signature(s) . . .

Note:
The bid security of ………..……………. has been counter guaranteed by the Bank ……..………...on
…………... ...……..………. (Applicable for Bid Security of Foreign Banks).
 2. Section V. Schedule of Requirements

1. Delivery and Completion Schedule

The delivery schedule expressed as weeks/months stipulates hereafter a delivery date which is the date of delivery (i) at
EXW premises, In order to determine the correct date of delivery hereafter specified, the Purchaser has taken into account
the additional time that will be needed for delivery to the Project Site or to another common place.2

Required Delivery Bidder’s offered

Schedule (In Delivery date [to
Number Description Quantity Unit Days ̸weeks/months be provided by
from the date of signing the bidder]
the contract)

2
The delivery may be specified for a single delivery , or for several partial deliveries, for a specific date, or range of acceptable delivery periods.
 2. Technical Specifications

The purpose of the Technical Specifications (TS) is to define the technical characteristics of the Goods
and Related Services required by the Purchaser. The TS, as a part of the schedule of Requirements (SR),
constitute a Contract document and are, therefore, a part of the Contract. The Purchaser must prepare the
TS and include them as a part of the Procurement Document, as applicable to each Contract.

Purchaser Requirement

Technical Description, Bidders Referenc

e page ̸ The bidder
It Name of Specifications, and proposed shall state as
Goods no. ̸
e Standards Catlogue Fully
page ̸ no. complaint/
m or Partially
Parti proposed technical
N complaint/
Related Require description,specifi
o. cular Non
Services ments cation and
complaint
s standard
Partic details
ulars

1 2 3 4 5 6

[Provide information on Column 1 to Column 4]

Bidders shall mention each and every proposed technical details as specified in the technical
details.
 Schedule of Requirement
1. List of Goods and Related Services
1 Office and computing machinery equipment and supplies
1.1 CCTV (Complete Accessories & Kit with 20 Cameras)

Procument Item Details

SL. No Item Description Unit of Measurement Quantity

1 2 MP Fixed lens camera with integrated audio recording system. PCs 17.0

2 4 MP Bullet Camera(outdoor) PCs 3.0

3 32 Channel NVR with Inbuilt Storage of 12 TB PCs 1.0

4 4 Port SFT Supported PoE Switch for 20 Cameras PCs 6.0

5 4 TB survelliance Hard disk for recording PCs 1.0

6 55" LED Monitor PCs 1.0

7 6U Network Rack PCs 1.0

1.2 Other Wiring and cabling Accessories

Procument Item Details

SL. No Item Description Unit of Measurement Quantity

1 4 Core Fiber Cable per meter Meters 475.0

2 Fiber Splicing PCs 15.0

3 Patch Cut PCs 15.0

4 SFP Jack 1,25G 020KM SC-SF (DU-G35/53-205-D) PCs 4.0

5 Cat-6 Cable pure Cooper Meters Approx 425.0

6 Power cable per meter Meters 90.0

7 Joint Box PCs 6.0

8 10/12 Waterproof Box PCs 6.0

9 1500VA Inverter Power backup for cctv PCs 1.0

10 150V AH Inverter Battery PCs 2.0

11 Wiring and cabling with other accessories for inverter setup PCs 1.0

12 20mm Listy PCs 40.0

13 25mm Listy PCs 20.0

14 40mm Listy PCs 10.0

1.3 Other Office Equipmets

Procument Item Details

SL. No Item Description Unit of Measurement Quantity

1 Installation Charge per Camera Lumsum 20.0

2 Branded Computer System PCs 10.0

3 Projector display board PCs 4.0

with slide presenter pen
4 Biometric attendance PCs 2.0
 Procument Item Details

SL. No Item Description Unit of Measurement Quantity

5 LED Display/Digital Board PCs 8.0

6 Aluminum Frame for Digital Board with installation charge and PCs 8.0
other accessories
7 Intercom Office System PCs 1.0

8 Intercom Telephone PCs 3.0

9 Installation Charge/Delivery/ Training charge Lumsum 1.0

2. Delivery and Completion Schedule

1 Office and computing machinery equipment and supplies

1.1 CCTV (Complete Accessories & Kit with 20 Cameras)
SL. Earliest Acceptable Bidder’s
Description of Goods Final Destination
No Delivery Date Delivery Date offered Delivery
1 2 MP Fixed lens camera with integrated Ripumardani Sainik Secondary After 30 days of After 45 days of
audio recording system. School, Bansbari Contact Contact
2 4 MP Bullet Camera(outdoor) Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
3 32 Channel NVR with Inbuilt Storage of Ripumardani Sainik Secondary After 30 days of After 45 days of
12 TB School, Bansbari Contact Contact
4 4 Port SFT Supported PoE Switch for 20 Ripumardani Sainik Secondary After 30 days of After 45 days of
Cameras School, Bansbari Contact Contact
5 4 TB survelliance Hard disk for Ripumardani Sainik Secondary After 30 days of After 45 days of
recording School, Bansbari Contact Contact
6 55" LED Monitor Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
7 6U Network Rack Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
1.2 Other Wiring and cabling Accessories
SL. Earliest Acceptable Bidder’s
Description of Goods Final Destination
No Delivery Date Delivery Date offered Delivery
1 4 Core Fiber Cable per meter Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
2 Fiber Splicing Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
3 Patch Cut Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
4 SFP Jack 1,25G 020KM SC-SF (DU- Ripumardani Sainik Secondary After 30 days of After 45 days of
G35/53-205-D) School, Bansbari Contact Contact
5 Cat-6 Cable pure Cooper Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
6 Power cable per meter Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
7 Joint Box Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
8 10/12 Waterproof Box Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
SL. Earliest Acceptable Bidder’s
Description of Goods Final Destination
No Delivery Date Delivery Date offered Delivery
9 1500VA Inverter Power backup for cctv Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
10 150V AH Inverter Battery Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
11 Wiring and cabling with other Ripumardani Sainik Secondary After 30 days of After 45 days of
accessories for inverter setup School, Bansbari Contact Contact
12 20mm Listy Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
13 25mm Listy Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
14 40mm Listy Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
1.3 Other Office Equipmets
SL. Earliest Acceptable Bidder’s
Description of Goods Final Destination
No Delivery Date Delivery Date offered Delivery
1 Installation Charge per Camera Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
2 Branded Computer System Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
3 Projector display board Ripumardani Sainik Secondary After 30 days of After 45 days of
with slide presenter pen School, Bansbari Contact Contact
4 Biometric attendance Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
5 LED Display/Digital Board Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
6 Aluminum Frame for Digital Board with Ripumardani Sainik Secondary After 30 days of After 45 days of
installation charge and other accessories School, Bansbari Contact Contact
7 Intercom Office System Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
8 Intercom Telephone Ripumardani Sainik Secondary After 30 days of After 45 days of
School, Bansbari Contact Contact
9 Installation Charge/Delivery/ Training Ripumardani Sainik Secondary After 30 days of After 45 days of
charge School, Bansbari Contact Contact
 Technical Specifications

1 Office and computing machinery equipment and supplies

1.1 CCTV (Complete Accessories & Kit with 20 Cameras)
Sl.
Description of Goods Particulars Requirements Bidder's Offer
No.
1 2 MP Fixed lens camera with integrated "Resolution: 2 MP "Resolution: 2 MP
audio recording system. Image Sensor: 1/2.8” Image Sensor: 1/2.8”
Progressive CMOS Sensor Progressive CMOS Sensor
Pixels: 1920 x 1080 Pixels: 1920 x 1080
Frame Rate: 25 FPS @ Frame Rate: 25 FPS @
1920 x 1080 1920 x 1080
Lens: 2.8 mm Fixed Lens" Lens: 2.8 mm Fixed Lens"

2 4 MP Bullet Camera(outdoor) "Resolution: 4 MP "Resolution: 4 MP

Image Sensor: 1/1.8” Image Sensor: 1/1.8”
Progressive Scan CMOS Progressive Scan CMOS
Pixels: 2560 X 1440 Pixels: 2560 X 1440
Frame Rate: 25 FPS @ Frame Rate: 25 FPS @
2560 X 1440 2560 X 1440
Lens: 4mm Lens: 4mm
Day Night: 24 hour Day Night: 24 hour
Colorful Video Colorful Video
Video Compression: H. Video Compression: H.
265+ Compression 265+ Compression
WDR: 120 dB WDR WDR: 120 dB WDR
Features: 3D DNR, BLC, Features: 3D DNR, BLC,
IRC, AGC, White Balance IRC, AGC, White Balance
Additional Features: HLC, Additional Features: HLC,
Defog Defog
On-board Storage: support On-board Storage: support
SD Card upto 128 GB SD Card upto 128 GB
Alarm Trigger: Motion Alarm Trigger: Motion
detection, video tampering detection, video tampering
detection, network detection, network
disconnected, IP address disconnected, IP address
conflict, illegal login, HDD conflict, illegal login, HDD
full, HDD error full, HDD error
General Function: One-key General Function: One-key
reset, three streams, reset, three streams,
heartbeat, mirror, password heartbeat, mirror, password
protection, privacy mask, protection, privacy mask,
watermark, IP address filter watermark, IP address filter
Smart Features: Line Smart Features: Line
Crossing Detection, Crossing Detection,
Intrusion Detection Intrusion Detection
OSD: Date, Time and OSD: Date, Time and
Camera Name Camera Name
Communication Interface: Communication Interface:
10/100M Ethernet Port 10/100M Ethernet Port
Protocols: TCP/IP, ICMP, Protocols: TCP/IP, ICMP,
HTTP, HTTPS, FTP, HTTP, HTTPS, FTP,
DHCP, DNS, DDNS, RTP, DHCP, DNS, DDNS, RTP,
RTSP, RTCP, NTP, UPnP, RTSP, RTCP, NTP, UPnP,
SMTP, IGMP SMTP, IGMP
Weather Protection: IP67 Weather Protection: IP67
Power: 12 Volt DC and Power: 12 Volt DC and
PoE" PoE"

3 32 Channel NVR with Inbuilt Storage of "Channel: 32 Channel "Channel: 32 Channel

12 TB Video Input Video Input
Incoming Bandwidth: Incoming Bandwidth:
Minimum 256 Mbps Minimum 256 Mbps
Outgoing Bandwidth: Outgoing Bandwidth:
Minimum 160 Mbps Minimum 160 Mbps
Recording Resolution: Upto Recording Resolution: Upto
8 MP 8 MP
Display Output: HDMI and Display Output: HDMI and
VGA VGA
HDMI Resolution: 4K HDMI Resolution: 4K
(3840 x 2160) (3840 x 2160)
Sl.
Description of Goods Particulars Requirements Bidder's Offer
No.
Third Party Camera Third Party Camera
Support: Yes Support: Yes
Synchronous Playback: 32 Synchronous Playback: 32
Channels Channels
Video Compression: H. Video Compression: H.
265+ Compression 265+ Compression
Audio: Supported Audio: Supported
Recording and Playback Recording and Playback
SATA Port: 4 SATA Port SATA Port: 4 SATA Port
SATA Port Capacity: Upto SATA Port Capacity: Upto
6 TB each 6 TB each
Inbuilt Storage: 12TB Inbuilt Storage: 12TB
(Surveillance Hard Disk) (Surveillance Hard Disk)
Communication Interface: Communication Interface:
10/100/1000M Ethernet 10/100/1000M Ethernet
Port Port
Network Protocol: TCP/IP, Network Protocol: TCP/IP,
DHCP, Cloud P2P, DNS, DHCP, Cloud P2P, DNS,
DDNS, NTP, SMTP, NFS, DDNS, NTP, SMTP, NFS,
iSCSI, UPnP, HTTP iSCSI, UPnP, HTTP
USB Interface: 2 x USB USB Interface: 2 x USB
Port" Port"

4 4 Port SFT Supported PoE Switch for 20 AS PER SAMPLE AS PER SAMPLE
Cameras
5 4 TB survelliance Hard disk for AS PER SAMPLE AS PER SAMPLE
recording
6 55" LED Monitor "Resolution: Full HD "Resolution: Full HD
Features Format: Smart" Features Format: Smart"

7 6U Network Rack AS PER SAMPLE AS PER SAMPLE

1.2 Other Wiring and cabling Accessories

Sl.
Description of Goods Particulars Requirements Bidder's Offer
No.
1 4 Core Fiber Cable per meter AS PER SAMPLE AS PER SAMPLE
2 Fiber Splicing AS PER SAMPLE AS PER SAMPLE

3 Patch Cut AS PER SAMPLE AS PER SAMPLE

4 SFP Jack 1,25G 020KM SC-SF (DU- AS PER SAMPLE AS PER SAMPLE
G35/53-205-D)
5 Cat-6 Cable pure Cooper Solid- bare coper, HDPE Solid- bare coper, HDPE
purer (Bare), Copper (305 purer (Bare), Copper (305
per box), 550 mHz per box), 550 mHz

6 Power cable per meter AS PER SAMPLE AS PER SAMPLE

7 Joint Box AS PER SAMPLE AS PER SAMPLE

8 10/12 Waterproof Box AS PER SAMPLE AS PER SAMPLE

9 1500VA Inverter Power backup for cctv AS PER SAMPLE AS PER SAMPLE

10 150V AH Inverter Battery AS PER SAMPLE AS PER SAMPLE

11 Wiring and cabling with other AS PER SAMPLE AS PER SAMPLE

accessories for inverter setup
12 20mm Listy AS PER SAMPLE AS PER SAMPLE

13 25mm Listy AS PER SAMPLE AS PER SAMPLE

14 40mm Listy AS PER SAMPLE AS PER SAMPLE

1.3 Other Office Equipmets
Sl.
Description of Goods Particulars Requirements Bidder's Offer
No.
1 Installation Charge per Camera AS PER SAMPLE AS PER SAMPLE

2 Branded Computer System Minimum requirement: i3 Minimum requirement: i3

(6thGen)Processor, 4GB (6thGen)Processor, 4GB
DDR3 RAM, 500 GB HD, DDR3 RAM, 500 GB HD,
19" Monitor, High Quality 19" Monitor, High Quality
Keyboard & Mouse Keyboard & Mouse

3 Projector display board "Brightness: 4,000 ANSI "Brightness: 4,000 ANSI

with slide presenter pen Lumens Lumens
Native Resolution: SVGA Native Resolution: SVGA
(800 x 600) (800 x 600)
Maximum Resolution: Maximum Resolution:
WUXGA (1,920 x 1,200) WUXGA (1,920 x 1,200)
Contrast Ratio: 30,000:1 Contrast Ratio: 30,000:1
Lamp Life/Type: 5,000/7, Lamp Life/Type: 5,000/7,
000/10,000 Hours 000/10,000 Hours
(Normal/Eco./Dynamic (Normal/Eco./Dynamic
Eco), 210W Eco), 210W
Image Size (Diagonal): 40"" Image Size (Diagonal): 40""
- 240"" - 240""
Projection Lens: F#2.46 – Projection Lens: F#2.46 –
2.66, f=21.8 - 25.6mm 2.66, f=21.8 - 25.6mm
Aspect Ratio: 4:3 Aspect Ratio: 4:3
Computer Compatibility: Computer Compatibility:
VGA (640 x 480) to VGA (640 x 480) to
WUXGA_RB(1920 x WUXGA_RB(1920 x
1200)" 1200)"

4 Biometric attendance "• Attendance Device with "• Attendance Device with
finger print system finger print system
including minimum 2000 including minimum 2000
mAh battery Backup mAh battery Backup

" "

5 LED Display/Digital Board "Module: P10 outdoor RGB "Module: P10 outdoor RGB
SMD LED module SMD LED module
Pixel Configuration: SMD Pixel Configuration: SMD
LED1R1G1B LED1R1G1B
Pixel Pitch: 10mm Pixel Pitch: 10mm
Lifetime: >=1,00,000 hours Lifetime: >=1,00,000 hours
Best Viewing Distance: Best Viewing Distance:
10m – 30m 10m – 30m
Weather Protection: IP65 Weather Protection: IP65
Colour option: R/G/B/Y/W Colour option: R/G/B/Y/W
Size: 2.5 X5 Size: 2.5 X5
" "

6 Aluminum Frame for Digital Board with Board fitting installation Board fitting installation
installation charge and other accessories cahrge per piece. cahrge per piece.

7 Intercom Office System Input 3 and Output 16 ports Input 3 and Output 16 ports

8 Intercom Telephone control panel display unit control panel display unit

9 Installation Charge/Delivery/ Training AS PER SAMPLE AS PER SAMPLE

charge
Conditions of Contract
 Section VI. General Conditions of Contract

1. Definitions 1.1 In this contract, the following terms shall be interpreted as indicated:
a. "The Contract" means the agreement entered into between the
Purchaser and the Supplier, as recorded in the Contract Form Signed
by the parties, including all attachments and appendices thereto and
all documents incorporated by reference therein;
b. "The Contract Price" means the price payable to the Supplier under the
contract for the full and proper performance of its contractual
obligation;
c. "The Goods" means Equipment and related Accessories and spare-
parts or any other materials which the Supplier is required to supply to
the Purchaser under the contract;
d. "Services" means services ancillary to the supply of the goods such as
transportation and insurance including the installation, commissioning
and the operational and maintenance training of the supplied
equipment.
e. "The Purchaser" means the procuring entity purchasing the goods;
f. "The Supplier" means the organization supplying the goods and
services under this contract.

2. Technical 2.1 The goods supplied under this contract shall confirm to the standards
Specification mentioned in the Technical Specification.

3. Patent Right 3.1 The Supplier shall indemnify the Purchaser against all third-party claims of
infringement of patent, trademark or industrial design rights arising from use
of goods or any part thereof in the Purchaser's country.
4. Performance 4.1 Within seven days (7) of receipt of award of contract from the Purchaser,
Security the successful Bidder shall furnish the performance security in the
Performance Security Form provided in the Bidding Documentsfor the due
performance of the Contract in the amounts specified in the SCC.
4.2 Failure of the successful Supplier to comply with the requirement of Sub -
clause 4.1 shall constitute sufficient grounds for the annulment of the award
and forfeiture of the bid security, in which event the Purchaser may make
the award to the next lowest Supplier or call for new sealed quotations.
4.3 The proceeds of the Performance Security shall be payable to the Purchaser
as compensation for any loss resulting from the Supplier’s failure to complete
its obligations under the Contract.
4.4 The validity of Performance Security shall be the sum of delivery period,
warranty period from the date of the issue of final acceptance certificate to
the Supplier and additional one month.
4.5 The performance security shall be released within 28 days of completion of
warranty period and upon submission of claim by the Supplier.

5. Inspection and 5.1 The Purchaser or its Representative shall have the right to inspect and/or
Tests test the goods to confirm their conformity to the Technical Specification and
the quality of performance after the supply and delivery of good to the
Purchaser's premises
5.2 The Purchaser may reject any Goods or any part thereof that fail to pass
any test and/or inspection or do not conform to the specifications. The
Supplier shall either rectify or replace such rejected Goods or parts thereof
or make alterations necessary to meet the specifications at no cost to the
Purchaser.

6. Packing 6.1 The Supplier shall provide such packing of the goods as is required to
prevent their damage or deterioration during transmit to their final
destination as indicated in the contract.
6.2 The packing shall be sufficient to withstand, without limitation, rough handling
during transit and exposure to extreme temperatures, salt and precipitation
during transit and open storage.
6.3 The packing, marking and documentation within and outside the packages
shall comply strictly with such special requirements as shall be expressly
provided in accordance with international standard and practice.

7. Delivery of 7.1 Delivery of the goods shall be made by the Supplier in accordance with the
Goods terms specified by the Purchaser in its Schedule of Requirements.

8. Insurance 8.1 The goods supplied under the contract shall be fully insured in the
currency of the Sealed Quotation price against loss or damage incidental to
manufacture or acquisition, transportation, storage and delivery in the manner
specified.
9. Warranty 9.1 The Supplier warrants that all the goods supplied under the contract shall
fully comply with the specification laid down in the contract.
9.2 Unless otherwise specified in the SCC, the warranty shall remain valid for
one year after the goods have been delivered to the final destination
indicated in the contract, and accepted by the Purchaser after installation
and commissioning of equipment by the Supplier.
9.3 The Purchaser shall promptly notify the Supplier in writing of any claims
arising under this warranty.
9.4 Upon receipt of such notice, the Supplier shall, with all reasonable speed,
replace the defective goods without cost to the Purchaser. The Supplier
will be entitled to remove, at its own risk and cost, the defective goods.

10. Payment 10.1 Payment shall be made in the Nepalese currency as specified in the SCC
10.2 Payment of the goods shall be made after the delivery and installation and
commissioning of goods (if applicable) to the satisfaction of the Purchaser.

11. Prices 11.1 Prices charged by the Supplier for goods delivered under the contract shall
not vary from the prices quoted by the Supplier in its sealed quotation.

12. Changed Order 12.1 Where the Purchaser desires to make changes in Schedule of
Requirement, it shall not exceed more than 15 percent.

13. Liquidated 13.1 If the Supplier fails to deliver any or all of the goods within the time period
Damages specified in the contract, the Purchaser shall, without prejudice to its other
remedies under the contract, deduct from the contract price, as liquidated
damages, a sum equivalent to 0.05 percent of the contract price of delayed
goods for each day of delay until actual delivery, up to a maximum
deduction of 10 percent of the delayed goods' contract price. Once the
maximum is reached, the Purchaser may consider termination of the
contract.

14. Resolution of 14.1 If any dispute or difference of any kind whatsoever shall arise between the
Disputes Purchaser and the Supplier in connection with or arising out of the Contract,
the parties shall make every effort to resolve amicably such dispute or
difference by mutual consultation.
14.2 If, after thirty (30) days, the parties have failed to resolve their dispute or
difference by such mutual consultation, then either the Purchaser or
Supplier may give notice to the other party of it’s intention to commence
arbitration, as hereinafter provided, as to the matter in dispute, and no
arbitration in respect of this matter may be commenced unless such notice
is given.
14.2.1 Any dispute or difference in respect of such a notice of intention to
commence arbitration has been given in accordance with this
Clause shall be finally settled by arbitration.Arbitration may be
 commenced prior to or after delivary of the Goods under the
Contract.
14.2.2 Arbitration proceedings shall be conducted in accordance with in
accordance with the rules of Nepal Council of Arbitration (NEPCA).
14.3 Notwithstanding any reference to arbitration herein,

a. the parties shall continue to perform their respective obligations under

the Contract unless they otherwise agree; and
b. the Purchaser shall pay the Supplier any monies due the Supplier.

15. Governing 15.1 The Governing Language shall be: Nepali or English
Language

16. Applicable Law 16.1 The applicable law shall be Laws of Nepal.

17. Notices 17.1 Any Notice given by one party to the other pursuant to the Contract shall be
in writing to the address specified in the SCC. The term “in writing” means
communicated in written form with proof of receipt
17.2 A Notice shall be effective when delivered or on the Notice’s effective date,
whichever is later.

18. Taxes and Duties 18.1 The Supplier shall be entirely responsible for all taxes, duties, licence fees
and other such levies imposed by the GON.

19. Operation, 19.1 The successful Supplier shall supply manufacturer's operation,
Maintenance and maintenance and spare-part manuals of the goods (Equipment) as
Spare-parts specified in SCC..
Manuals

20. Conduct of 20.1 The Supplier shall be responsible to fulfil his obligations as per the
Suppliers requirement of the Contract Agreement, Quotation documents, GoN’s
Procurement Act and Regulations.
20.2 The Supplier shall not carry out or cause to carryout the following acts with
an intention to influence the implementation of the procurement process or
the procurement agreement :
a. give or propose improper inducement directly or indirectly,
b. distortion or misrepresentation of facts
c. engaging or being involved in corrupt or fraudulent practice
d. interference in participation of other prospective bidders.
e. coercion or threatening directly or indirectly to impair or harm, any
party or the property of the party involved in the procurement
proceedings,
 f. collusive practice among bidders before or after submission of bids for
distribution of works among bidders or fixing artificial/uncompetitive
bid price with an intention to deprive the Purchaser the benefit of
open competitive bid price..
g. contacting the Purchaser with an intention to influence the Purchaser
with regards to the bid or interference of any kind in examination and
evaluation of the bids during the period after opening of bids up to the
notification of award of contract

21. Blacklisting 21.1 Without prejudice to any right of the Purchaser under this Contract, the GoN,
Supplier Public Procurement and Monitoring Office (PPMO) may blacklist a Supplier
for his conduct up to three years on the following grounds and seriousness
of the act committed by the supplier:
a. if it is proved that the supplier committed acts pursuant to the Sub -
clause 20.2,
b. if the supplier fails to sign an agreement pursuant to ITB Clause 24,
c. if it is proved later that the supplier had committed substantial defect in
implementation of the contract or had not substantially fulfilled his
obligations under the contract or the completed work is not of the
specified quality as per the contract ,
d. if convicted by a court of law in a criminal offence which disqualifies the
supplier from participating in the contract.

21.2 A Supplier declared blacklisted and ineligible by the GON shall be ineligible
to bid for a contract during the period of time determined by PPMO and
credit information bureau of Nepal.
 Section VII - Special Conditions of Contract (SCC)

This SCC forms part of the Agreement

[Note: with the exception of the items for which the Purchaser's requirements have been inserted, the Bidder shall complete the
following information before submitting his Sealed Quotation.]

GCC 1.1.1 The Purchaser shall be: Ripumardini Sainik Secondary School
(e)

GCC 4.1 The Currency of of the performance Security shall be in Nepalese Rupees.The amount of the performance security shall
be as follows:
(i) if bid price of the bidder selected for acceptance is up to 15 (fifteen) percent below the approved cost estimate, the
performance security amount shall be 5 (five) percent of the bid price.
(ii) For the bid price of the bidder selected for acceptance is more than 15 (fifteen) percent below of the cost estimate, the
performance security amount shall be determined as follows:
(iii) Performance Security Amount =[(0.85 x Cost Estimate – Bid Price) x 0.5] + 5% of Bid Price.

The Bid Price and Cost Estimate shall be inclusive of Value Added Tax.

GCC 9.1 The warranty period shall be : [12]

GCC 10 The terms of payment to be made to the Supplier under the contract shall be as follows: Through accounts division/unit of
the Purchaser
Payments shall be made in Nepalese Rupees in the following manner:
Sample provisions:
Advance Payment:[Usually not more than twenty (20)] percent of the contract price shall be paid within thirty (30) days of
signing of the contract, and upon submission of request for advance and a bank guarantee from Commercial Bank or
Financial Institution eligible to issue Bank Guarantee as per prevailing Law for equivalent amount valid until the goods
are delivered and accepted and in the form provided in the Bidding Document.

On Delivery and acceptance:[Hundred (100) percent. of the Contract Price of the Goods and related services (installation
and commissioning of goods (if applicable)) to the satisfaction of the Purchaser delivered shall be paid within thirty (30)
days upon submission of Tax Invoice and claim supported by the acceptance certificate issued by the Purchaser or its
authorized person/s. Advance payment shall be deducted and settled in this payment.
or
On Delivery [Usually eighty (80)] percent. of the Contract Price of the Goods and related services delivered shall be paid
within thirty (30) days of receipt of the Goods and upon submission of Tax Invoice.

On acceptance: [Usually eighty (20)] percent. of the Contract Price of the Goods and related services (installation and
commissioning of goods (if applicable)) to the satisfaction of the Purchaser. delivered shall be paid within thirty (30) days
upon submission of Tax Invoice and claim supported by the acceptance certificate issued by the Purchaser or its authorized
person/s
or
On Delivery and acceptance: One Hundred (100)] percent. of the Contract Price of the Goods and related services delivered
shall be paid within thirty (30) days of receipt of the Goods and related services (installation and commissioning of goods
(if applicable)) to the satisfaction of the Purchaser. and upon submission of Tax Invoice and claim supported by the
acceptance certificate issued by the Purchaser or its authorized person/s
TDS shall be deducted as per the prevailing rules and regulations.
[Delete those not appropriate]
Payments shall be made in Nepalese Rupees in the following manner:.

SL No Milestone Name Payment Percentage

1 Advance payment 0

2 Delivery to site 100.0

GCC 17.1 For notices, the Purchaser’s address shall be:

Attention: Ripumardini Sainik Secondary School

Address: Ripumardini Sainik Secondary School

Bansbari
Kathmandu, Kathmandu
Nepal
Designation:

Telephone: 01-4374335 Facsimile Number:

Electronic Mail Address:

GCC 17.1 For notices, the Suppliers’s address shall be:

Attention:

Address:

Designation:

Telephone: Facsimile Number:

Electronic Mail Address:

GCC 19.1 The Supplier shall supply [12]number of copies manufacturer's operation, maintenance and spare-part manuals of the
goods (Equipment) in English or Nepali language as specified in SCC.
 Section VIII. Contract Form
1. Letter of Acceptance
[on letterhead paper of the Purchaser]

Date……..

To: (name and address of the Contractor )

Subject: .......... Notification of Award

This is to notify that your Sealed Quotation dated . . . . for execution of the . . . . . . . . . .name of
the contract and identification number, as given in the Contract Data/SCC . . . . . . . . . . for the Contract
price of Nepalese Rupees [insert amount in figures and words in Nepalese Rupees], as
corrected in accordance with the Instructions to Bidders is hereby accepted in accordance with
the Instruction to Bidders.

You are hereby instructed to contract this office to sign the formal contract agreement within 7
days. As per the Conditions of Contract, you are also required to submit Performance Security,
as specified in SCC, consisting of a Bank Guarantee in the format included in Section VIII
(Contract Forms) of the Bidding Document.

The Purchaser shall forfeit the bid security, in case you fail to furnish the Performance Security
and to sign the contract within specified period.

Authorized Signature: ......................................................................

Name and Title of Signatory:

 2. Contract Agreement

THIS AGREEMENT made the _____ day of __________ 20_____ between [name of Purchaser] (hereinafter
called “the Purchaser”) of the one part and [name of Supplier] of [city and country of Supplier] (hereinafter called
“the Supplier”) of the other part:

WHEREAS the Purchaser invited Sealed Quotation for certain goods and ancillary services, viz., [brief description
of goods and services] and has accepted a SQ by the Supplier for the supply of those goods and services in the sum
of ………………………………………………. [contract price in words and figures] (hereinafter called “the
Contract Price”).

NOW THIS AGREEMENT WITNESSETH AS FOLLOWS:

1. In this Agreement words and expressions shall have the same meanings as are respectively assigned to them
in the Conditions of Contract referred to.
2. The following documents shall be deemed to form and be read and construed as part of this Agreement,
viz.:
a. Form of Agreement
b. The Purchaser’s Notification of Award
c. The General Conditions of Contract;
d. Special Conditions of Contract
e. Quotation Form and the Price Schedule submitted by the Supplier;
f. The Schedule of Requirements;
.
3. In consideration of the payments to be made by the Purchaser to the Supplier as hereinafter mentioned, the
Supplier hereby covenants with the Purchaser to provide the goods and services and to remedy defects
therein in conformity in all respects with the provisions of the Contract.
4. The Purchaser hereby covenants to pay the Supplier in consideration of the provision of the goods and
services and the remedying of defects therein, the Contract Price or such other sum as may become payable
under the provisions of the contract at the times and in the manner prescribed by the Contract.
IN WITNESS whereof the parties hereto have caused this Agreement to be executed in accordance with
their respective laws the day and year first above written.
On behalf of the Purchaser On behalf of the Supplier
Name: Name:
Designation: Designation:
Sign: Sign:
Seal: Seal:
 3. Performance Security

Date :

To: [name and address of the Purchaser]

WHEREAS [insert complete name of Supplier] (hereinafter “the Supplier”) has received
the notification of award for the execution of [insert identification number and name of
contract] (hereinafter “the Contract”).
AND WHEREAS it has been stipulated by you in the aforementioned Contract that the
Supplier shall furnish you with a security [insert type of security] issued by a reputable
guarantor for the sum specified therein as security for compliance with the Supplier’s
performance obligations in accordance with the Contract.
AND WHEREAS the undersigned [insert complete name of Guarantor], legally
domiciled in [insert complete address of Guarantor], (hereinafter the “Guarantor”), have
agreed to give the Supplier a security:
THEREFORE WE hereby affirm that we are Guarantors and responsible to you, on behalf
of the Supplier, up to a total of [insert currency and amount of guarantee in words and
figures] and we undertake to pay you, upon your first written demand declaring the Supplier
to be in default under the Contract, without cavil or argument, any sum or sums within the
limits of [insert currency and amount of guarantee in words and figures] as aforesaid,
without your needing to prove or to show grounds or reasons for your demand or the sum
specified therein.
This security is valid until the [insert day, month, year].
Name: [insert complete name of person signing the Security]
In the capacity of: [insert legal capacity of person signing the Security]
Signed: [insert signature of person whose name and capacity are shown above]
Duly authorized to sign the security for and on behalf of: [insert seal and complete name of
Guarantor]
Date: [insert date of signing]
 4. Bank Guarantee for Advance Payment

To: [name of the Purchaser]

[name of Contract]

Gentlemen and/or Ladies:

In accordance with the payment provision included in the Contract, which amends Clause 10 of the General
Conditions of Contract to provide for advance payment, [name and address of Supplier] (hereinafter called “the
Supplier”) shall deposit with the Purchaser a bank guarantee to guarantee its proper and faithful performance under
the said Clause of the Contract in an amount of [amount of guarantee in figures and words].

We, the [bank or financial institution], as instructed by the Supplier, agree unconditionally and irrevocably to
guarantee as primary obligator and not as surety merely, the payment to the Purchaser on its first demand without
whatsoever right of objection on our part and without its first claim to the Supplier, in the amount not exceeding
[amount of guarantee in figures and words].

We further agree that no change or addition to or other modification of the terms of the Contract to be performed
there under or of any of the Contract documents which may be made between the Purchaser and the Supplier, shall
in any way release us from any liability under this guarantee, and we hereby waive notice of any such change,
addition, or modification.

The validity period of the guarantee shall be 30 days beyond the period scheduled for repayment of the advance
payment and the guarantee shall remain valid and in full effect from the date of the advance payment under the
Contract until the Purchaser receives full repayment of the same amount from the Supplier.

Yours truly,

Signature and seal of the Guarantors

[name of bank or financial institution]

[address]

[date]
AS PER SAMPLE
 lznaGbL b/efp सम्बन्धी k]z ug'kg]{ कागजातहरु
l;=g+= ljj/)f s}lkmot
-s_ g]kfnL gful/stfsf] k|df)fkq
-v_ kmd{, ;+:yf jf sDkgL btf{sf] k|df)fkq
-u_ Joj;fo btf{{sf] O{hfhtkq
-#_ d"No clej[l¢ s/ btf{ k|df)fkq / :yfoL n]vf btf{ gDa/ -Kofg_ k|df)fkq .
cfGtl/s /fhZj ljefuaf^ cf=j=075÷76 sf] s/ r"Stf u/]sf] k|df)fkq jf
-ª_
Dofb yk ePsf] kq
af]nkqdf x:tfIf/ ug{ clwsf/gfdf kq lbPsf] eP ;f] sf] clwsf/gfdfsf]]
-r_
sfuhft
-%_ ;+o"Qm pkqmd ;DaGwL ;Demf}tf -;+o"Qm pkqmd agfO{ af]nkq k]z ePsf] eP_
-h_ lnlvt ?kdf u/]sf] #f]if)ffkq

-em_ jf/]G^L÷Uof/]G^L tyf dd{t ;Def/ ;]jf pknAw u/fpg] ;DaGwL kq .

af]nkqbftfn] k|bfg ug"{kg]{ cfjZos tflnd -sfof{no pks/)fsf] xsdf_ ;DalGw

-`_ kq .

-^_ af]nkq k]z u/]sf] lgj]bg .

-&_ cfaZos ;fdfu|L ;lxtsf] d"No k|:tfj kmf/fd .

-*_ Af}+saf^ hf/L ePsf] adf]lhd Aff]nkq hdfgt hDdf u/]sf] ;Ssn} a}+s ef}r/ .

af]nkqbftfn] af]nkq b:t"/ afktsf] /sd ?=1000 -Ps xhf/_ o; ljBfnon]

Pg cfO{ ;L Plzof a}+s, dxf/fhu+h, sf&df)*f}df vf]n]sf] ljBfyL{ w/f}^L vftf
-(_
g+=1341066776524002 sfof{nosf] gfdM >L l/k"dlb{gL ;}lgs df=lj=,
af+;jf/L, sf&df)*F}, .