AREQUIPA PERU TEMPLE MHTN PROJECT NO 2014532.

00
THE CHURCH OF JESUS CHRIST OF LATTER DAY SAINTS DESIGN DEVELOPMENT

SECTION 064023 - INTERIOR ARCHITECTURAL WOODWORK

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 1 Specification Sections, apply to this Section.

1.2 SUMMARY

A. This Section includes the following:

1. Interior standing and running trim.

2. Wood casework, including altar tops and kneelers.
3. Stone countertops.
4. Plastic-laminate cabinets.
5. Solid-surfacing countertops.
6. Interior ornamental wood grilles.
7. Pews and benches.
8. Speaker enclosures.
9. Security safe to be installed with millwork.
10. Closet hardware.
11. Framing for Plasma Monitor Lift.
12. Line shaft driven operator for Plasma Monitor Lift.
13. Shop finishing interior woodwork.

B. Related Sections include the following:

1. Division 5 Section “Decorative Metal” for cast metal panels and medallions that are
installed with wood grilles and trim.
2. Division 6 Section "Miscellaneous Carpentry" for wood furring, blocking, shims, and
hanging strips required for installing woodwork and concealed within other construction
before woodwork installation.
3. Division 6 Section "Paneling.”
4. Division 8 Section "Stile and Rail Wood Doors."
5. Division 9 Section 090000 “Finish Matrix” for finish information related to work of
this section.

1.3 DEFINITIONS

A. Interior architectural woodwork includes wood furring, blocking, shims, hanging strips and cleats
for installing woodwork items, unless concealed within other construction before woodwork
installation.

1.4 SUBMITTALS

A. Product Data: For each type of product indicated, including cabinet hardware and accessories,
and finishing materials and processes.

INTERIOR ARCHITECTURAL WOODWORK 064023 - 1

AREQUIPA PERU TEMPLE MHTN PROJECT NO 2014532.00
THE CHURCH OF JESUS CHRIST OF LATTER DAY SAINTS DESIGN DEVELOPMENT

B. Product Data: For hardboard, medium-density fiberboard, particleboard, plywood, adhesive for
bonding, thermoset shelving decorative overlay, solid-surfacing material, stone materials,
cabinet hardware and accessories, and finishing materials and processes.

C. Shop Drawings: Submit shop drawings in conformance with AWS – Section 1 Submittals. The
first page of the original shop drawings shall bear a Woodwork Institute Certified Compliance
Label. Show location of each item, dimensioned plans and elevations, large-scale details,
attachment devices and other components.

1. Show details full size.

2. Show locations and sizes of furring, blocking, and hanging strips, including
concealed blocking and reinforcement specified in other Sections.
3. Show location and sizes of cutouts and holes for items installed in woodwork.
4. Pews and Benches: Show seating layout, aisle widths, aisle-end alignment or stepping,
chairs widths, and chair spacing in each row. Show locations and features accessories,
including left- and right-hand tablet arms, book racks, and accessibility provisions.

D. Samples for Verification: For the following:

1. Solid wood for transparent finish, 12” L x 4” W, for each species and cut, finished on 1
face and 1 edge.
2. Veneer leaves representative of and selected from flitches approved by Architect, to be
used for transparent-finished woodwork.
3. Wood-veneer-faced panel products with or for transparent finish, 12 by 12 inches,
for each species and cut. Include at least one center-match face-veneer seam and finish
as specified.
4. Wood and panel products with shop-applied opaque finish, 5 inches (125 mm) wide by 12
inches (300 mm) long for lumber and 12 by 12 inches (300 by 300 mm) for panels, for
each finish system and color, with exposed surface finished.
5. Stone materials, 6 inches (150 mm) square.
6. Plastic-laminate-clad panel products, 8 by 10 inches (200 by 250 mm), for each
type, color, pattern, and surface finish, with separate samples of unfaced panel product
used for core.
7. Thermoset decorative-overlay surfaced panel products, 8 by 10 inches (200 by 250 mm),
for each type, color, pattern, and surface finish.
8. Solid-surfacing materials, 6 inches (150 mm) square.
9. Corner pieces as follows:

a. Cabinet front frame joints between stiles and rail as well as exposed end pieces,
12 inches high by 12 inches wide by 6 inches deep.
b. Miter joints for standing trim

10. Miter joints for standing trim.

11. Fabric (Pews and Benches): 12 inch (300 mm) square fabric sample showing texture,
color, etc.
12. Samples of closet hardware: 12-inch long tubing section; 1 flange sample; 1
hanger sample.
13. Exposed cabinet hardware and accessories, one unit for each type and finish.

E. Product Certificates: Numbered by AWI and signed by AWI inspectors that the products and
finished work comply with requirements of the specifications.

F. Woodwork Quality Standard Compliance Certificates: AWI Quality Certification Program

certificates.
 G. Qualification Data: For firms and persons specified in "Quality Assurance" Article to
demonstrate their capabilities and experience. Include lists of completed projects with project
names and addresses, names and addresses of architects and owners, and other information
specified.

H. Closeout Submittals (Pews and Benches): Include final, executed copy of warranty.

1.5 QUALITY ASSURANCE

A. Installer Qualifications: An experienced installer who has completed architectural woodwork

similar in material, design, and extent to that indicated for this Project and whose work
has resulted in construction with a record of successful in-service performance.

B. Fabricator Qualifications: A firm experienced in producing architectural woodwork similar to that

indicated for this Project and with a record of successful in-service performance, as well
as sufficient production capacity to produce required work.

C. Installer Qualifications: Certified Compliance Program, Licensee to issue AWI Certified

Compliance Certificate, with original submittals, or Non-AWI-Licensee to provide Certified
Tracking Acknowledgement, issued with original submittals.

D. Source Limitations: Engage a qualified woodworking firm to assume undivided responsibility for
production and installation of interior architectural woodwork and sequence match wood
veneers.

E. Quality Standard: Millwork and installation shall be in accordance with Premium grade of the
Architectural Woodwork Standards, latest edition. If provisions of the Grade specified are
in conflict with , or modified by the drawings and/or specifications, the modifications shall
govern.

1. Provide AWI certification labels and compliance certificate indicating that woodwork
complies with the requirements and grades specified.

F. Mockups: Build mockups to verify selections made under sample submittals and to demonstrate
aesthetic effects and set quality standards for materials and execution.

1. Build mockups of typical standing and running trim, architectural wood cabinets,
stone countertops, ornamental wood grilles, and pews and benches, in transparent and
shop- applied opaque finish, as shown on Drawings.
2. Subject to compliance with requirements, approved mockups may become part of
the completed Work if undisturbed at time of Substantial Completion.

G. Preinstallation Conference: Conduct conference at Project site to comply with requirements in

Division 1 Section "Project Meetings."

1.6 DELIVERY, STORAGE, AND HANDLING

A. Do not deliver woodwork until wet work, painting and similar operations that could
damage woodwork have been completed in installation areas. If woodwork must be stored in
other than installation areas, store only in areas where environmental conditions comply with
requirements specified in "Project Conditions" Article.

1. Complete the following before delivering pews to construction site:

 a. Floor coverings.
b. Architectural woodwork, including finishing.
c. Painting, including art painting.

1.7 PROJECT CONDITIONS

A. Environmental Limitations: Do not deliver or install woodwork until building is enclosed,

wet work is complete, and HVAC system is operating and maintaining temperature and
relative humidity at occupancy levels between 25 and 55 percent during the remainder of
the construction and installation period.

B. Field Measurements: Where woodwork is indicated to fit to other construction, verify dimensions
of other construction by field measurements before fabrication and indicate measurements
on Shop Drawings. Coordinate fabrication schedule with construction progress to avoid
delaying the Work.

1. Locate concealed framing, blocking, and reinforcements that support woodwork by field
measurements before being enclosed and indicate measurements on Shop Drawings.
2. Established Dimensions: Where field measurements cannot be made without delaying
the Work, establish “hold to” dimensions and proceed with fabricating woodwork without
field measurements. Provide allowance for trimming at site, and coordinate construction
to ensure that actual dimensions correspond to established dimensions.

1.8 COORDINATION

A. Coordinate sizes and locations of framing, blocking, furring, reinforcements, and other related
units of Work specified in other Sections to ensure that interior architectural woodwork can be
supported and installed as indicated.

PART 2 - PRODUCTS

2.1 INTERIOR TRIM, WOOD CABINETS AND ORNAMENTAL WOOD GRILLES – FABRICATORS

A. Acceptable Fabricators Selected to Bid the Work (Institutional-Quality Wood-Working):

Final selection of Fabricator to perform the work will also be based upon the submittal of a
physical mock-up showing wood finish, detailed method of anchoring and installation, and shop
drawings of mock-up.

Fetzer Architectural Woodwork.

Fondell Inc.
Wavell-Huber.

2.2 MATERIALS

A. General: Provide materials that comply with requirements of 2009 Architectural Woodwork
Standards quality standard for each type of woodwork and quality grade specified, unless
otherwise indicated
 B. Fabricator shall use veneers from logs selected by the Owner and Architect, purchased by the
Contractor. Fabricator shall verify selected logs are sized adequately, including waste, to
complete the project.

C. Wood Species and Cut for Transparent Finish: M1 as noted in Section 090000 “Finish Matrix”.

D. Wood Species for Opaque Finish: Any close-grained hardwood except Rock Maple at any trim
below 10’-0” AFF

E. Wood Products: Comply with the following:

1. Hardboard: AHA A135.4.

2. Medium-Density Fiberboard: ANSI A208.2, Grade MD-Exterior Glue.
3. Particleboard: ANSI A208.1, Grade M-2-Exterior Glue.
4. Softwood Plywood: DOC PS 1, Medium Density Overlay.
5. Hardwood Plywood and Face Veneers: HPVA AA Grade.

F. Thermoset Decorative Overlay: Particleboard complying with ANSI A208.1, Grade M-2, or
medium-density fiberboard complying with ANSI A208.2, Grade MD, with surface of
thermally fused, melamine-impregnated decorative paper complying with LMA SAT-1.

G. High-Pressure Decorative Laminate: NEMA LD 3, grades as indicated, or if not indicated, as

required by woodwork quality standard.

H. Adhesive for Bonding Plastic Laminate: Contact cement.

I. Solid-Surfacing Material: Homogeneous solid sheets of filled plastic resin complying with
material and performance requirements in ANSI Z124.3, for Type 5 or Type 6, without a
precoated finish.

J. Tempered Float Glass for Doors and Sidelights: Specified in Division 8 Sections “Glazing” and
“Art Glass”.

2.3 ALTAR TOPS AND KNEELERS

A. High-Density Foam Basis of Design: Future Foam HR33250Y.

1. Density: 2.5 lbs./ft.

2. Tensile Strength: 10.0 PSI.
3. Elongation: 100%.
4. Tear: 1.0 PPI.
5. Compression Set (75%): 10% maximum.
6. Sag Factor: 2.40 minimum.
7. Flammability: Pass TB117, Section A, Part I and Section D, Part II.
8. Thickness: As shown on drawings.

B. Glue:

1. Quality Standards:

a. US Plywood JMK514.
b. Prestoset.
c. Weldwood.
d. Perkins L-100.
 C. Upholstery Fabric Manufacturer, Pattern and Color: M4, M5 and M6, as noted in Section
090000 “Finish Matrix”:

D. Miscellaneous Hardware: Supply necessary screws, washers, miscellaneous hardware, and

instructions for a complete and removable assembly and installation.

2.4 STONE COUNTERTOPS

A. Granite: Comply with ASTM C 615.

B. Description: Uniform, stone without veining.

C. Cut stone from contiguous, matched slabs in which natural markings occur.

D. Finish: Polished.

E. Stone Type: M3 as noted in Section 090000 “Finish Matrix”.

F. Countertop Edge: 1-1/2 inches, mitred.

2.5 CABINET HARDWARE AND ACCESSORIES

A. General: Provide cabinet hardware and accessory materials associated with architectural
cabinets, except for items specified in Division 8 Section "Door Hardware."

B. Hardware Standard: Comply with BHMA A156.9 for items indicated by referencing BHMA
numbers or items referenced to this standard.

C. Frameless Concealed Hinges (European Type): BHMA A156.9, B01602, 170 degrees of
opening, self-closing.

D. Back-Mounted Pulls: BHMA A156.9, B02011.

E. Pulls: H1 through H3 as noted in Section 090000 “Finish Matrix”.

F. Adjustable Shelf Standards and Supports: Hafele 5 mm diameter metal shelf rests for 32 mm
boring system or equal.

G. Shelf Rests: BHMA A156.9, B04013.

H. Drawer Slides: Side-mounted, full-extension, zinc-plated steel drawer slides with steel ball
bearings, manufactured by Accuride or equal, and rated for the following loads:

1. Box Drawer Slides: 100 lbf (440 N).

I. Door Locks: BHMA A156.11, E07121. Coordinate with drawings for locations

J. Drawer Locks: BHMA A156.11, E07041. Coordinate with drawings for locations

K. Grommets for Cable Passage through Countertops: 2-inch (51-mm)OD, Metal US10 bronze
finish with matching caps with slot for wire passage.

1. Product: Subject to compliance with requirements, by Doug Mockett and Co., Inc.
 L. Exposed Hardware Finishes: For exposed hardware, provide finish that complies with
BHMA A156.18 for BHMA finish number indicated.

1. US10 Bronze.

2. US 4 Satin Brass

3. Coordinate finishes to match adjacent door hardware.

M. For concealed hardware, provide manufacturer's standard finish that complies with product
class requirements in BHMA A156.9.

2.6 PEWS AND BENCHES

A. Wood:

1. General:

a. 6 percent maximum moisture content during construction.

b. No mineral grains will be acceptable.

2. Opaque Finished Wood: Plain sawn natural hard maple.

3. Wood Species and Cut for Transparent Finish:

a. M1 as noted in Section 090000 “Finish Matrix”.

b. 6 percent maximum moisture content during construction.
c. No mineral grains will be acceptable.

4. Underlayment for Seat: ¾ inch (19 mm) plywood.

5. Backs: 1 inch x 4-1/5 inches (25 by 113 mm) maximum width.
6. Supports: 1-1/4 inch (32 mm) minimum thickness.

B. Padding:

1. 1.8 lb. per cu ft density polyurethane foam.

2. 2-3/4 inch (70 mm) thick seats, one inch (25 mm) thick on backs.

C. Glue:

1. Quality Standards:

a. US Plywood JMK514.
b. Prestoset.
c. Weldwood.
d. Perkins L-100.

D. Pew Custom Wood End Panel:

1. Design: See drawings.

2. Material and Finish: M1 and M2 as noted on drawings and in Section 090000 “Finish
Matrix”.

E. Upholstery Fabric Manufacturer, Pattern and Color: As noted in Section 090000 “Finish Matrix”:
 1. Chapel Pews: M19.
2. Baptistry Pews: M11.

F. Miscellaneous Hardware: Supply necessary screws, washers, miscellaneous hardware, and

instructions for complete pew assembly and installation.

G. Approved Manufacturers:

1. Straight Pews:

a. Marshall Company, Payette, ID. www.marshallpews.com.

b. Sauder Manufacturing Co., Archbold, OH. www.saudermanufacturing.com.
c. Fabricators of Architectural Woodwork specified in this section.

2.7 SPEAKER ENCLOSURES

A. Speaker Enclosures: Perforated steel sheet attached to steel tube structure, with adhered grille
cloth painted to match adjacent ceiling structure.

1. Perforated Steel Sheet: McNichols hexagonal perforated, 16 gauge plain steel, ½” hex on
9/16” staggered center.
2. Paint steel support structure and perforated steel sheet flat black prior to attachment of
the grille cloth.
3. Grille Cloth: Acoustone FR 7000.

a. Adhere grille cloth to perforated steel sheet and paint to match surrounding
adjacent surfaces.
b. Painted fabric must remain porous, such that light can be seen through all pores.
c. Fabricate for easy removal and replacement of grille cloth.
d. Grille Cloth Paint Color: As noted in Section 090000 “Finish Matrix”.

4. Construct speaker enclosure assembly to provide easy maintenance access to the

speakers.

2.8 SECURITY SAFE

A. Security Safe: Construct millwork cabinet to receive and receive Security Safe, in
locations noted on drawings.

1. Security Safe: AMSEC BLB2018.

a. Outside Dimensions: 20.5” high x 18.5” wide x 15” deep.

b. Door Opening: 18” high x 16” wide.
c. Weight: 200 lbs.
d. Lock: ESL (Electronic Safe Lock) Series, ESL10, with A/C Power Kit.

2.9 CLOSET HARDWARE

A. Manufactured Units:

1. Provide closet rods in locations shown on drawings.

 a. Hollow rod, 1-1/4” diameter, 1/16” metal thickness, oil-rubbed bronze finish,
lengths as indicated on drawings.

2. Provide one set closet rod flanges for each closet rod.
a. Design Standard: Rocklin Item No. 30835, 1-5/16” diameter, oil-rubbed bronze
finish.

3. Provide one hanger for each 2-1/2 inches of closet rod length.
a. Design Standard: EMCO #13, ball top, walnut finish.

2.10 INSTALLATION MATERIALS

A. Furring, Blocking, Shims, and Hanging Strips: Softwood or hardwood lumber, kiln-dried to less
than 15 percent moisture content.

B. Anchors: Select material, type, size, and finish required for each substrate for secure
anchorage. Provide nonferrous-metal or hot-dip galvanized anchors and inserts on inside face
of exterior walls and elsewhere as required for corrosion resistance. Provide toothed-steel or
lead expansion sleeves for drilled-in-place anchors.

C. Interlocking wall cleat system for installation of wall paneling and wainscot. Solid wood
wall cleat. (French cleat)

2.11 FABRICATION, GENERAL

A. Interior Woodwork Grade: Premium.

B. Wood Moisture Content: 6 to 8 percent in relation to ambient relative humidity during

fabrication and installation.

C. Fabricate woodwork to dimensions, profiles, and details indicated.

D. Complete fabrication, including assembly and hardware application, before shipment to Project
site. Disassemble components only as necessary for shipment and installation. Where
necessary for fitting at site, provide ample allowance for scribing, trimming, and fitting.

1. Notify Architect seven days in advance of the dates and times woodwork fabrication will
be complete.
2. Trial fit assemblies at fabrication shop that cannot be shipped completely
assembled. Install dowels, screws, bolted connectors, and other fastening devices
that can be removed after trial fitting. Verify that various parts fit as intended and check
measurements of assemblies against field measurements indicated on Shop
Drawings before disassembling for shipment.

E. Shop cut openings, to maximum extent possible, to receive hardware, appliances,

plumbing fixtures, electrical work, and similar items. Locate openings accurately and use
templates or roughing-in diagrams to produce accurately sized and shaped openings. Sand
edges of cutouts to remove splinters and burrs.

1. Seal edges of openings in countertops with two coats of waterproof sealer.

F. Install glass to comply with applicable requirements in Division 8 Section "Glazing" and in
GANA's "Glazing Manual." For glass in wood frames, secure glass with removable stops.
2.12 INTERIOR STANDING AND RUNNING TRIM

A. Quality Standard: Comply with 2009 Architectural Woodwork Standards Section 6 “Interior and
Exterior Millwork”.

B. Grade: Premium.

C. For trim items wider than available lumber, use veneered construction. Do not glue for width.

D. For rails wider or thicker than available lumber, use veneered construction. Do not glue
for width or thickness.

E. Backout or groove backs of flat trim members and kerf backs of other wide, flat
members, except for members with ends exposed in finished work.

F. Wood Species and Cut for Transparent Finish: M1 as noted in Section 090000 “Finish Matrix”.

G. Wood Species for Opaque Finish: Any close-grained hardwood.

2.13 WOOD CABINETS FOR TRANSPARENT FINISH

A Quality Standard: Comply with 2009 Architectural Woodwork Standards Section 10,
. “Casework”.

B Grade: Premium.
.
C. Type of Cabinet Construction: Face frame construction with flush overlay doors and drawers.

D. Wood Species and Cut for Exposed Surfaces: M1 as noted in Section 090000 “Finish Matrix”.

1. Grain Matching: Vertical.

2. Matching of Veneer Leaves: Book matching or diamond matching, as indicated on
drawings.

E. Semiexposed Surfaces: Provide surface materials indicated below:

1. Surfaces Other Than Drawer Bodies: Compatible species to that indicated for exposed
surfaces, stained to match.
2. Drawer Sides and Backs: Solid-hardwood lumber, stained to match species indicated for
exposed surfaces.

2.14 WOOD CABINETS FOR OPAQUE FINISH

A. Quality Standard: Comply with 2009 Architectural Woodwork Standards Section 10,
“Casework”.

B. Grade: Premium.

C. Type of Cabinet Construction: Face frame construction with flush overlay doors.

D. Wood Species for Exposed Lumber Surfaces: Any closed-grain hardwood.

E. Panel Product for Exposed Surfaces: Medium-density fiberboard.

 F. Semiexposed Surfaces: Provide surface materials indicated below:

1. Surfaces Other Than Drawer Bodies: Match materials indicated for exposed surfaces.

G. Join subfronts, backs, and sides with glued rabbeted joints supplemented by mechanical
fasteners or glued dovetail joints.

2.15 PLASTIC-LAMINATE CABINETS

A. Quality Standard: Comply with Section 10, 2009 AWS STANDARDS requirements for laminate
cabinets.

B. AWI Type of Cabinet Construction: Flush overlay with all cabinet bodies ¾ inch thick minimum
and all shelves minimum 1-½ inches thick for all spans.

C. Laminate Cladding for Exposed Surfaces: High-pressure decorative laminate complying with
the following requirements:

1. Horizontal Surfaces Other Than Tops: HGS.

2. Postformed Surfaces: HGP.
3. Vertical Surfaces: HGS.
4. Edges: PVC Edging full depth of edge. Color to match laminate or as selected by
Architect. Colors may not be standard with all manufacturers.

D. Materials for Semiexposed Surfaces: Provide surface materials indicated below:

1. Surfaces Other Than Drawer Bodies: Thermoset decorative overlay.

2. Drawer Sides and Backs: Thermoset decorative overlay.
3. Drawer Bottoms: Thermoset decorative overlay.

E. Colors, Patterns, and Finishes: As indicated in Section 090000 “Finish Matrix”.

2.16 SOLID-SURFACING-MATERIAL COUNTERTOPS

A. Quality Standard: Comply with AWI Section 11 of 2009 AWI STANDARDS requirements for
countertops.

B. Solid-Surfacing-Material Thickness: 1/2 inch.

C. Colors, Patterns, and Finishes: M10, as indicated in Section 090000 “Finish Matrix”.

D. Fabricate tops in one piece with shop-applied edges, unless otherwise indicated. Comply with
solid-surfacing-material manufacturer's written recommendations for adhesives, sealers,
fabrication, and finishing.

2.17 INTERIOR ORNAMENTAL WOOD GRILLES

A. Quality Standard: Comply with 2009 Architectural Woodwork Standards Section 6 “Interior and
Exterior Millwork” and Section 8 “Wall Surfacing”.

B. Grade: Premium.
AREQUIPA PERU TEMPLE MHTN PROJECT NO 2014532.00
THE CHURCH OF JESUS CHRIST OF LATTER DAY SAINTS DESIGN DEVELOPMENT

C. Transparent Finish Wood Species and Cut: M1 as noted in Section 090000 “Finish Matrix”.

D. Opaque Finish Wood Species: Any closed-grain hardwood.

2.18 FABRICATION, PEWS AND BENCHES

A. Pew bodies 144 inches or less in length shall be one piece:

1. Longer pews may be assembled with blind joint.

2. Joint shall occur over center support.

B. Pew Ends:
1. Rift block construction is preferred, however, edge-glued construction is acceptable
providing manufacturer will guarantee satisfactory performance.
2. Minimum thickness shall be 1-3/4 inches.
3. Rout end ½ inch deep to receive back and seat.
4. Pew body shall be wedged and screwed to end.
5. Custom end panel: See drawings.

C. Pew Supports:

1. Rift block or edge-glued construction and 1-1/4 inches minimum thickness.

2. Terminate supports within 2 inches of cap rail.
3. Seat and back shall be in full contact with support member so no wedging is required at
seat and no molding is required to hide joint with pew back. Maximum spacing between
supports shall be 72 inches.

D. Upholstering: Where possible, railroad fabrics to achieve seamless construction of fronts and
seat of pews.

2.19 MISCELLANEOUS LUMBER

A. General: Provide miscellaneous lumber for support or attachment other construction, including
the following:

1. Framing.
2. Blocking.

B. For concealed boards, provide lumber with 15 percent maximum moisture content and
any of the following species and grades:

1. Hem-fir or hem-fir (north), Construction or 2 Common grade; NLGA, WCLIB, or WWPA.

2. Poplar.
3. Western woods, Construction or No. 2 Common grade; WCLIB or WWPA.

C. For blocking and nailers used for attachment of other construction, select and cut lumber
to eliminate knots and other defects that will interfere with attachment of other work.

D. Size framing to accommodate a motorized plasma LCD lift, Model No. 1001.5-P, manufactured
by Auton Motorized Systems.

1. Overall width 40”.

2. Platform width 37.25”.
 3. Depth 9”.
4. Overall Height: 30”.

2.20 PLASMA MONITOR LIFT OPERATOR

A. General: Provide motorized lift operator for plasma monitor.

B. Design Requirements:

1. Line shaft driven (direct drive) system shall be connected to building structure as
shown on Drawings.
2. It shall be able to raise or lower curtain with working load as applied by system heights
as shown on Drawings.
3. Hoist system shall contain appropriate number of winding spools (typically 18-
20” spacing), motor and gear reducer, coupled together with common shaft.
4. Connections shall be made with resilient mounting devices to reduce vibration and noise.

C. Performance Requirements:

1. Curtain shall operate at less than 42 decibels within audience chamber.

2. Curtain shall operate between two predetermined stops for up and down positions.
3. Hand-cranking capacity at motor in case of power failure.

D. Hoist Components:

1. Motors and Gear Boxes:

a. Variable Frequency Drive (VFD).

1) 1-phase 110V input, 3-phase 220V output.

2) Electronic braking and programmable speed control.
3) Twenty-four volt control to interface with Audio Visual system with option
for control at motor.

b. Gearbox ratio to allow curtain to open in 10 seconds. Adjustable at VFD.

c. Provide brake as needed to insure steady weight-bearing in the up position.
d. Three-phase, ½ horsepower minimum. NEMA service factor of 1.25 for continuous
operation. Fan cooled.

2. Shaft Clutch:

a. Adjustable torque.
b. Automatic reset.

3. Enclosed Rotary Limit Switch Assembly:

a. Unlimited adjustability.
b. One pair of micro switches for normal operating limits.
c. Switch to be mounted to drive train allowing for easy adjustment.
d. Switch driven from drive train by means of roller chain.
e. Sprocket size to allow for maximum usable travel of limit switch cams.

4. Connecting Shafts:
 a. 5/8” solid steel shaft machined with flat side at .040” off diameter.
b. Supported in self-aligning pillow blocks, with ball-bearings isolated in
rubber- encased housings for quiet operation.

5. Winding Spools:

a. Designed to properly support required load without crushing or deformation.

b. Spool to accommodate ¼” wide, woven twill tape for lift lines.
c. Spool hub set screwed to shaft.

2.21 SHOP FINISHING

A. Quality Standard: Comply with 2009 Architectural Woodwork Standards Section 5 “Finishing”,
unless otherwise indicated.

B. Grade: Premium.

C. General: Finish architectural woodwork at fabrication shop as specified in this Section. Defer
only final touchup, cleaning, and polishing until after installation.

D. Preparations for Finishing: Comply with referenced quality standard for sanding, sealing
concealed surfaces, and similar preparations for finishing architectural woodwork, as applicable
to each unit of work.

1. Sand exposed sold wood and veneered surfaces with 220 grit for finish
preparation. Veneer sand-through is unacceptable

2. Repair and conceal all grain separation, endgrain, chip-out, millmarks, sanding scratches
and other blemishes due to milling and fabrication, on all exposed wood surfaces prior to
finishing.

3. Render finish brad fastening points unnoticeable. Use of wood putty is not acceptable

4. Backpriming: Apply two coats of sealer or primer, compatible with finish coats, to
concealed surfaces of woodwork. Concealed surfaces of plastic-laminate-clad woodwork
do not require backpriming when surfaced with plastic laminate, backing paper, or
thermoset decorative overlay.

E. Transparent Finish (all transparent-finished items except pews and benches): Comply with
requirements indicated below for grade, finish system, staining, and sheen, with sheen
measured on 60-degree gloss meter per ASTM D 523:

1. Grade: Premium.
2. Architectural Woodwork Standards Finish System: System - 11, catalyzed polyurethane.
3. Color/Staining: Match Architect's sample as noted in Section 090000 “Finish Matrix”.
4. Sheen: Satin, 30-50 gloss units.

F. Transparent Finish for Pews and Benches: Comply with requirements indicated below for grade,
finish system, staining, and sheen, with sheen measured on 60-degree gloss meter per ASTM
D 523:

1. Grade: Premium.
2. Stain: Penetrating, non-fading sealer/stain hand-wiped to obtain best possible uniform
color.
 3. Filler: Use of filler is not required if high quality finish can be achieved without it.
4. Sealer for Stained Pews: Apply one hot coat of lacquer sealer follow by hand sanding
with #240 wet dry paper.
5. Lacquer for Stained Pews:

a. Apply three coats of hot lacquer using no reducer to thin material.

b. Lightly sand between coats.

6. Finish surface shall be free of skips, runs, sags, and sanding dust.

G. Opaque Finish for Casework and Cabinetry: (Post-Bid Addendum 03, Nov. 12, 2012)

1. Grade: Premium.
2. Architectural Woodwork Standards Finish System: System - 11, catalyzed polyurethane
(for close-grain woods). Finishing steps include the following, in addition to all rules and
requirements noted in AWI Architectural Woodwork Standards, Section 5 – Finishing:

a. Wash coat, reduced vinyl sealer.

b. Sealer, vinyl.
c. First topcoat.
d. Second topcoat.

3. Color: Match paint colors as noted on Section 090000 Finish Matrix.

4. Sheen: Gloss level 5, 35 -70 gloss units.

H. Opaque Finish for Interior Millwork and Wood Trims:

1. Shop prime with one coat of wood primer specified in Division 9 Section “Painting”.
2. Two finish coats by Division 9 Section “Painting”.

PART 3 - EXECUTION

3.1 PREPARATION

A. Stabilize and maintain temperature within occupancy range, and humidity within 25 and 55% at
least one week prior to the date of jobsite arrival for the architectural woodwork.

B. Condition woodwork to average prevailing humidity conditions in installation areas before

installation.

C. Before installing architectural woodwork, examine shop-fabricated work for completion and
complete work as required, including removal of packing and backpriming.

3.2 INSTALLATION

A. Quality Standard: Install woodwork to comply with the 2009 Architectural Woodwork Standards
for the same grade specified in Part 2 of this Section for type of woodwork involved.

B. Grade: Premium
C. Install woodwork level, plumb, true, and straight. Shim as required with concealed shims.
Install level and plumb (including tops) to a tolerance of 1/8 inch in 96 inches (3 mm in 2400
mm).

D. Scribe and cut woodwork to fit adjoining work, and refinish cut surfaces and repair damaged
finish at cuts.

E. Standing and Running Trim:

1. Anchor woodwork to anchors or blocking built in or directly attached to substrates.

Secure with concealed fasteners and blind nailing as required for complete installation.
Use fine finishing nails for exposed fastening, countersunk and filled flush with woodwork
and matching final finish if transparent finish is indicated.
2. Install with minimum number of joints possible, using full-length pieces (from maximum
length of lumber available) to greatest extent possible. Do not use pieces less than 60
inches (1500 mm) long, except where shorter single-length pieces are necessary.
3. Install standing and running trim with no more variation from a straight line than 1/8 inch
in 96 inches (3 mm in 2400 mm).

F. Cabinets: Install without distortion so doors and drawers fit openings properly and are
accurately aligned. Adjust hardware to center doors and drawers in openings and to provide
unencumbered operation. Complete installation of hardware and accessory items as indicated.

1. Install cabinets with no more than 1/8 inch in 96-inch (3 mm in 2400-mm) sag, bow, or
other variation from a straight line.
2. Maintain veneer sequence matching of wood cabinets with transparent finish, from
cabinet to cabinet.
3. Fasten wall cabinets through back, near top and bottom, at ends and not more than 16
inches (400 mm) o.c. with No. 10 wafer-head screws sized for 1-inch (25-mm)
penetration into wood or metal framing, blocking, or hanging strips

G. Countertops: Anchor securely by screwing through corner blocks of base cabinets or

other supports into underside of countertop.

1. Align adjacent stone countertops and form seams to comply with manufacturer's written
recommendations using adhesive in color to match countertop. Carefully dress joints
smooth, remove surface scratches, and clean entire surface.
2. Install countertops with no more than 1/8 inch in 96-inch (3 mm in 2400-mm) sag, bow, or
other variation from a straight line.
3. Secure backsplashes to tops with concealed metal brackets at 16 inches (400 mm) o.c.
and to walls with adhesive.
4. Calk space between backsplash and wall with sealant specified in Division 7
Section "Joint Sealants."

H. Interior Ornamental Wood Grilles:

1. Install at locations and heights noted on drawings.

2. Fasten with concealed fasteners. Face fastening is unacceptable.
3. Installation tolerances:

a. Variation from a straight line: 1/8 inch in 96 inches.

b. Plumb: 1/8 inch in 96 inches.

I. Pews and Benches:

 1. Install securely to floor with concealed fasteners. Angles or 8-clips are not acceptable.
2. When installing over carpet, punch holes through carpet with hollow cutting tool. Do not
drill.
3. Spacing and alignment shall be uniform and true.

J. Closet Hardware:

1. Install closet rods plumb, properly aligned, and securely fastened in place, complying
with the drawings and manufacturer’s recommendations.

K. Plasma Monitor Lift Operator:

1. Coordinate fabrication of lift operator with installation of plasma monitor.

2. Coordinate with Automatic Control and Audio-Visual Systems.

3.3 DEMONSTRATION

A. After plasma monitor lift operator installation is completed and after interface with audio /
visual system, demonstrate for Architect, Owner's Representative, and Temple Presidency
operation and maintenance procedures of motor-operated system.

3.4 ADJUSTING AND CLEANING

A. Repair damaged and defective woodwork, where possible, to eliminate functional and
visual defects; where not possible to repair, replace woodwork. Adjust joinery for uniform
appearance.

B. Clean, lubricate, and adjust hardware.

C. Clean woodwork on exposed and semiexposed surfaces. Touch up shop-applied finishes to

restore damaged or soiled areas.

END OF SECTION 064023

AREQUIPA PERU TEMPLE MHTN PROJECT NO 2014532.00
THE CHURCH OF JESUS CHRIST OF LATTER DAY SAINTS DESIGN DEVELOPMENT

SECTION 064220 – PANELING

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 1 Specification Sections, apply to this Section.

1.2 SUMMARY

A. This Section includes the following:

1. Wood paneling.

B. Related Sections include the following:

1. Division 6 Section "Miscellaneous Carpentry" for wood furring, blocking, shims, and
hanging strips required for installing paneling and that are concealed within other
construction before paneling installation.
2. Division 6 Section "Interior Architectural Woodwork" for interior woodwork other than
paneling.
3. Division 8 Section "Stile and Rail Wood Doors."
4. Division 9 Section 090000 “Finish Matrix” for finish information related to work of
this Section.

1.3 DEFINITIONS

A. Paneling includes wood furring, blocking, and shims for installing paneling, unless
concealed within other construction before paneling installation.

1.4 SUBMITTALS

A. Product Data: For each type of product indicated, including finishing materials and processes.

B. Product Data: For panel products, adhesives, sound damping spray backing, and finishing
materials and processes.

C. Shop Drawings: Show location of paneling, large-scale details, attachment devices, and other
components. Include dimensioned plans and elevations.

1. Show details full size.

2. Show locations and sizes of furring and blocking, including concealed blocking specified
in other Sections.
3. For paneling produced in sets, show finished panel sizes, set numbers, sequence
numbers within sets, and method of cutting panels to produce indicated sizes.
4. For paneling veneered in fabrication shop, show veneer leaves with dimensions,
grain direction, exposed face, and identification numbers indicating the flitch and
sequence within the flitch for each leaf.

PANELING 064220 - 1
 D. Samples for Verification: For the following:

1. Lumber with or for transparent finish, 12” L x 4” W, for each species and cut, finished on
1 side and 1 edge.
2. Veneer leaves selected from approved flitches to be used for transparent-finished
paneling.
3. Wood-veneer-faced panel products with or for transparent finish, 12 by 24 inches (300 by
600 mm), for each species and cut. Include at least one center-match face-veneer seam
and finish as specified.
4. Wood and panel products with shop-applied opaque finish, 5 inches (125 mm) wide by 12
inches (300 mm) long for lumber and 12 by 12 inches (300 by 300 mm) for panels,
for each finish system and color, with exposed surface finished.

E. Product Certificates: Numbered by AWI and signed by AWI inspectors that the products
and finished work comply with requirements of the specifications.

F. Qualification Data: For firms and persons specified in "Quality Assurance" Article to
demonstrate their capabilities and experience. Include lists of completed projects with project
names and addresses, names and addresses of architects and owners, and other information
specified.

1.5 QUALITY ASSURANCE

A. Installer Qualifications: An experienced installer who has completed paneling similar in material,
design, and extent to that indicated for this Project and whose work has resulted in
construction with a record of successful in-service performance.

B. Fabricator Qualifications: A firm experienced in producing paneling similar to that indicated for
this Project and with a record of successful in-service performance, as well as sufficient
production capacity to produce required units. Shop is a certified participant in AWI's
Quality Certification Program.

C. Source Limitations: A qualified woodworking firm to assume undivided responsibility for

production and installation of paneling with sequence-matched wood veneers and wood doors
faced with veneers from same flitches as paneling.

D. Quality Standard: Unless otherwise indicated, comply with the 2009 AWI / AWMAC / WI
"Architectural Woodwork Standards" for grades of paneling, construction, finishes, and
other requirements.
1. Provide AWI certification labels and compliance certificate indicating that paneling
complies with requirements of grades specified.

E. Mockups: Before fabricating and installing paneling, build mockups for each form of
construction and finish required to verify selections made under sample Submittals and to
demonstrate aesthetic effects and qualities of materials and execution. Build mockups to
comply with the following requirements, using materials indicated for the completed Work:

1. Build mockups in the location and of the size indicated or, if not indicated, as directed by
Architect.
2. Notify Architect seven days in advance of dates and times when mockups will be
fabricated.
3. Demonstrate the proposed range of aesthetic effects and workmanship.
4. Obtain Architect's approval of mockups before starting paneling fabrication.
 5. Maintain mockups during construction in an undisturbed condition as a standard for
judging the completed Work.
6. Approved mockups may become part of the completed Work if undisturbed at time
of Substantial Completion.

F. Preinstallation Conference: Conduct conference at Project site to comply with requirements in

Division 1 Section "Project Meetings."

1.6 DELIVERY, STORAGE, AND HANDLING

A. Do not deliver paneling until wet work, painting and similar operations that could damage
paneling have been completed in installation areas. If paneling must be stored in other
than installation areas, store only in areas where environmental conditions comply with
requirements specified in "Project Conditions" Article.

1.7 PROJECT CONDITIONS

A. Environmental Limitations: Do not deliver or install paneling until building is enclosed, wet work
is complete, and HVAC system is operating and will maintain temperature between 60
and 90 deg F (16 and 32 deg C) and relative humidity between 25 and 50 percent during
the remainder of the construction and installation period.

B. Field Measurements: Where paneling is indicated to fit to other construction, verify dimensions
of other construction by field measurements before fabrication and indicate measurements
on Shop Drawings. Coordinate fabrication schedule with construction progress to avoid
delaying the Work.
1. Locate concealed framing, blocking, and reinforcements that support paneling by
field measurements before being enclosed and indicate measurements on Shop
Drawings.
2. Established Dimensions: Where field measurements cannot be made without delaying
the Work, establish dimensions and proceed with fabricating paneling without field
measurements. Provide allowance for trimming at site, and coordinate construction to
ensure that actual dimensions correspond to established dimensions.

1.8 COORDINATION

A. Coordinate sizes and locations of framing, blocking, furring, reinforcements, and other
related units of Work specified in other Sections to ensure that paneling can be installed as
indicated.

PART 2 - PRODUCTS

2.1 PANELING FABRICATORS

A. Acceptable Fabricators Selected to Bid the Work (Institutional-Quality Wood-Working):

Final selection of Fabricator to perform the work will also be based upon the submittal of a
physical mock-up showing wood finish, detailed method of anchoring and installation, and shop
drawings of mock-up.

Fetzer Architectural Woodwork.

Fondell Inc.
Wavell-Huber.
2.2 MATERIALS

A. Fabricator shall use veneers from logs selected by the Owner and Architect, purchased by the
Contractor. Fabricator shall verify selected logs are sized adequately, including waste, to
complete the project.

B. General: Provide materials that comply with requirements of the Architectural Woodwork
Standards for quality grade specified, unless otherwise indicated.

C. Wood Products: Comply with the following:

1. Hardboard: AHA A135.4.
2. Medium-Density Fiberboard: ANSI A208.2, Grade MD-Exterior Glue.
3. Particleboard: ANSI A208.1, Grade M-2-Exterior Glue.
4. Softwood Plywood: DOC PS 1, Medium Density Overlay.
5. Hardwood Plywood and Face Veneers: HPVA AA Grade.

2.3 INSTALLATION MATERIALS

A. Furring, Blocking, Shims, and Hanging Strips: Softwood or hardwood lumber, kiln-dried to less
than 15 percent moisture content.

B. Anchors: Select material, type, size, and finish required for each substrate for secure
anchorage. Provide nonferrous-metal or hot-dip galvanized anchors and inserts on inside face
of exterior walls and elsewhere as required for corrosion resistance. Provide toothed-steel
or lead expansion sleeves for drilled-in-place anchors.

2.4 FABRICATION, GENERAL

A. Paneling Grade: Provide Premium grade paneling complying with the referenced quality
standard.

B. Wood Moisture Content: Comply with requirements of the referenced quality standard for wood
moisture content during fabrication and in installation areas.

C. Arrange paneling in shop or other suitable space in proposed sequence for examination
by Architect. Mark units with temporary sequence numbers to indicate position in proposed
layout.

1. Lay out one elevation at a time if approved by Architect.

2. Notify Architect seven days in advance of the date and time when layout will be available
for viewing.
3. Provide lighting of similar type and level as that of final installation for viewing
layout, unless otherwise approved by Architect.
4. Do not trim end units and other nonmodular size units to less than modular size until after
Architect's approval of layout.
5. Obtain Architect's approval of layout before start of assembly. Mark units and Shop
Drawings with assembly sequence numbers based on approved layout.

D. Complete fabrication and assembly before shipment to Project site. Disassemble components
only as necessary for shipment and installation. Where necessary for fitting at site, provide
ample allowance for scribing, trimming, and fitting.

1. Notify Architect seven days in advance of the dates and times paneling fabrication will be
complete.
 2. Trial fit assemblies at fabrication shop that cannot be shipped completely
assembled. Install dowels, screws, bolted connectors, and other fastening devices
that can be removed after trial fitting. Verify that various parts fit as intended and check
measurements of assemblies against field measurements indicated on approved
Shop Drawings before disassembling for shipment.

E. Shop cut openings, to maximum extent possible, to receive hardware, electrical work, and
similar items. Locate openings accurately and use templates or roughing-in diagrams to
produce accurately sized and shaped openings. Sand edges of cutouts to remove splinters and
burrs.

2.5 CUSTOM WOOD PANELING

A. Quality Standard: Comply with 2009 Architectural Woodwork Standards Section 8 “Wall
Surfacing”.

B. Grade: Premium.

C. Wood Species and Cut for Transparent Finish: M1 as noted in Section 090000 “Finish Matrix”.
Edge Banded where noted.

D. Transparent-Finish Paneling Veneer Matching:

1. Matching between adjacent veneer leaves (horizontally), as indicated on drawings:

Sequence-match and book match; sequence match and diamond match.
2. Matching between adjacent veneer leaves (vertically): Continuous sequenced slip match.
3. Matching within individual panel faces: Center-balance-match.
4. Matching of panels within a room or area: Blue-print-match.

E. Wood Species for Opaque Finish: Maple at wainscots and chair rails.

2.6 SHOP FINISHING

A. Quality Standard: Comply with 2009 Architectural Woodwork Standards Section 5 “Finishing”,
unless otherwise indicated.

1. Grade: Premium.

B. General: Finish paneling at fabrication shop as specified in this Section. Defer only final
touchup, cleaning, and polishing until after installation.

C. Preparations for Finishing: Comply with referenced quality standard for sanding, sealing
concealed surfaces, and similar preparations for finishing paneling, as applicable to each unit of
work.
1. Backpriming: Apply two coats of sealer or primer, compatible with finish coats, to
concealed surfaces of paneling.

D. Transparent Finish: Comply with requirements indicated below for grade, finish system,
staining, and sheen, with sheen measured on 60-degree gloss meter per ASTM D 523:

1. Grade: Premium.
2. Architectural Woodwork Standards Finish System: System – 11, catalyzed polyurethane.
3. Color/Staining: Match Architect's sample as noted in Section 090000 “Finish Matrix”.
 4. Sheen: Satin, 30-50 gloss units.

E. Opaque Finish:

1. Grade: Premium.
2. Architectural Woodwork Standards Finish System: System - 11, catalyzed polyurethane.
3. Color: Match paint colors as noted on Section 090000 Finish Matrix.
4. Sheen: Gloss, 61-100 gloss units.

PART 3 - EXECUTION

3.1 PREPARATION

A. Condition paneling to average prevailing humidity conditions in installation areas before

installation.

B. Before installing paneling, examine shop-fabricated work for completion and complete work as
required, including removal of packing and backpriming.

3.2 INSTALLATION

A. Quality Standard: Install paneling to comply with the 2009 Architectural Woodwork Standards
for the same grade specified in Part 2 of this Section for type of paneling involved.

B. Install paneling level, plumb, true, and straight with no distortions. Shim as required with
concealed shims. Install level and plumb to a tolerance of 1/8 inch in 96 inches (3 mm in 2400
mm). Install with no more than 1/16 inch in 96-inch (1.6 mm in 2400-mm) vertical cup or bow
and 1/8 inch in 96-inch (3 mm in 2400-mm) horizontal variation from a true plane.

1. For flush paneling with revealed joints, install with variations in reveal width, alignment of
top and bottom edges, and flushness between adjacent panels not exceeding 1/32 inch
(0.8 mm).

C. Scribe and cut paneling to fit adjoining work, and refinish cut surfaces and repair
damaged finish at cuts.

D. Anchor paneling to supporting substrate with concealed panel-hanger clips. Do not use
face fastening.

E. Complete the finishing work specified in this Section in the shop before delivery and installation
of paneling. Apply specified finish coats, including stains and paste fillers if any, to exposed
surfaces where only sealer/prime coats were applied in shop.

3.3 ADJUSTING AND CLEANING

A. Repair damaged and defective paneling, where possible, to eliminate functional and visual
defects; where not possible to repair, replace paneling. Adjust for uniform appearance.

B. Clean paneling on exposed surfaces. Touch up shop-applied finishes to restore damaged

or soiled areas.
END OF SECTION 064220
SECTION 071113 - BITUMINOUS DAMPPROOFING

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 1 Specification Sections, apply to this Section.

1.2 SUMMARY

A. This Section includes the following:

1. Cold-applied, applied to stone panels that occur at or below grade

1.3 SUBMITTALS

A. General: Submit each item in this Article according to the Conditions of the Contract and
Division 1 Specification Sections.

B. Product data for each type of product specified, including data substantiating that materials
comply with requirements for each dampproofing material specified. Include recommended
method of application, recommended primer, number of coats, coverage or thickness, and
recommended protection course.

1. Certification by dampproofing manufacturer that products supplied comply with local

regulations controlling use of volatile organic compounds (VOCs).

1.4 QUALITY ASSURANCE

A. Installer Qualifications: Engage an experienced Installer who has completed bituminous

dampproofing similar in material, design, and extent to that indicated for this Project and with a
record of successful in-service performance.

B. Single-Source Responsibility: Obtain primary dampproofing materials and primers from one
source and by a single manufacturer. Provide secondary materials only as recommended by
manufacturer of primary materials.

1.5 PROJECT CONDITIONS

A. Substrate: Proceed with dampproofing only after substrate construction and penetrating work
have been completed.

B. Weather Limitations: Proceed with dampproofing only when existing and forecasted weather
conditions will permit work to be performed according to manufacturer's recommendations and
warranty requirements.

BITUMINOUS DAMPPROOFING 071113 - 1

PART 2 - PRODUCTS

2.1 MANUFACTURERS

A. Manufacturers: Subject to compliance with requirements, manufacturers offering products that

may be incorporated into the Work include the following:

1. ChemMasters Corp.
2. Degussa Building Systems; Sonneborn Brand Products. Hydrocide 700
3. Gardner Gibson, Inc.
4. Henry Company.
5. Karnak Corporation.
6. Koppers Inc.
7. Malarkey Roofing Products.
8. Meadows, W. R., Inc.
9. Tamms Industries, Inc.

2.2 COLD APPLIED EMULSIFIED ASPHALT DAMPROOFING

A. Design Standard: Sonneborn Hydrocide 700, 700B

B. Trowel Coats: ASTM D 1227, Type II, Class 1.

C. Fibered Brush and Spray Coats: ASTM D 1227, Type II, Class 1.

D. VOC Content: 0.25lb/gal. (30g/L) or less.

2.3 BITUMINOUS DAMPPROOFING

A. General: Provide products recommended by manufacturer for designated application/

B. Cold-Applied, Cut-Back (Solvent-Based) Asphalt Dampproofing:

1. Trowel Coats: ASTM D 41.

2. Brush and Spray Coats: ASTM D 4479, Type I.

2.4 MISCSCELLANEOUS MATERIALS

C. Cut-Back Asphalt Primer: ASTM D 41.

D. Glass Fabric: Woven glass fabric, treated with asphalt, complying with ASTM D 1668, Type I.

E. Protection Course, Roll Roofing Type: Smooth-surfaced roll roofing, complying with
ASTM D 224, Type II.
AREQUIPA PERU TEMPLE MHTN PROJECT NO 2014532.00
THE CHURCH OF JESUS CHRIST OF LATTER DAY SAINTS DESIGN DEVELOPMENT

PART 3 - EXECUTION

3.1 PREPARATION

A. Clean substrate of projections and substances detrimental to work; comply with

recommendations of prime materials manufacturer.

B. Install cant strips and similar accessories as shown and as recommended by prime
materials manufacturer even though not shown.

C. Fill voids, seal joints, and apply bond breakers, if any, as recommended by prime
materials manufacturer, with particular attention at construction joints.

D. Install separate flashings and corner protection stripping, as recommended by prime materials
manufacturer, where indicated to precede application of dampproofing. Comply with details
shown and with manufacturer's recommendations. Pay particular attention to requirements
at building expansion joints, if any.

E. Prime substrate as recommended by prime materials manufacturer.

F. Protection of Other Work: Do not allow liquid and mastic compounds to enter and clog drains
and conductors. Prevent spillage and migration onto other surfaces of work by masking or
otherwise protecting adjoining work.

3.2 INSTALLATION, GENERAL

A. Comply with manufacturer's recommendations except where more stringent requirements

are indicated and where Project conditions require extra precautions to ensure satisfactory
performance of work.

B. Apply dampproofing to provide continuous plane of protection on exterior stone panels.

1. Lap dampproofing at least 1/4 inch (6 mm) onto flashing, reinforcement, ties, and
other items that penetrate.
2. Extend dampproofing over outer face of structural members that extend through the wall,
and lap dampproofing at least 1/4 inch (6 mm) onto shelf angles supports.

C. Application: Apply dampproofing to the following surfaces.

1. Concealed faces of stone panels

D. Reinforcement: At changes in plane or where otherwise shown as “reinforced,” install

lapped course of glass fabric in first coat of dampproofing compound before it thickens.

E. Bituminous Cant Strips: Install 2-by-2-inch (50-by-50-mm) cant strip of bituminous grout at base
of vertical dampproofing where it meets horizontal surface.

3.3 COLD-APPLIED, EMULSIFIED-ASPHALT DAMPPROOFING

A. On interior Face of stone panels apply one brush or spray coat at not less than 1 gal./35 sq. ft.
with finished product pinhole free when cured.
AREQUIPA PERU TEMPLE MHTN PROJECT NO 2014532.00
THE CHURCH OF JESUS CHRIST OF LATTER DAY SAINTS DESIGN DEVELOPMENT

END OF SECTION 071113

AREQUIPA PERU TEMPLE MHTN PROJECT NO 2014532.00
THE CHURCH OF JESUS CHRIST OF LATTER DAY SAINTS DESIGN
DEVELOPMENT

SECTION 071115 – BITUMINOUS DAMPPROOFING – LANDSCAPE

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and Division 1 Specification Sections, apply to this Section.

1.2 SUMMARY

A. This Section includes the following:

1. Cold-applied, cut-back asphalt dampproofing for foundations and masonry cavity

walls, for landscaping components.

1.3 SUBMITTALS

A. Product Data: For each type of product indicated. Include recommendations for method of
application, primer, number of coats, coverage or thickness, and protection course.

1.4 QUALITY ASSURANCE

A. Source Limitations: Obtain primary dampproofing materials and primers through one source
from a single manufacturer. Provide secondary materials recommended by manufacturer of
primary materials.

1.5 PROJECT CONDITIONS

A. Weather Limitations: Proceed with installation only when existing and forecasted weather
conditions permit dampproofing to be performed according to manufacturers' written
instructions.

B. Ventilation: Provide adequate ventilation during application of dampproofing in enclosed

spaces. Maintain ventilation until dampproofing has cured.

PART 2 - PRODUCTS

2.1 COLD-APPLIED, CUT-BACK ASPHALT DAMPPROOFING

A. Manufacturers: Subject to compliance with requirements, provide products by one of the

following:

1. ChemMasters Corp.
2. Degussa Building Systems; Sonneborn Brand Products.
3. Henry Company.
4. Koppers Inc.
5. Meadows, W. R., Inc.
6. Tamms Industries, Inc.

B. Trowel Coats: ASTM D 4586, Type I, Class 1, fibered.

C. Brush and Spray Coats: ASTM D 4479, Type I, fibered or nonfibered].

BITUMINOUS DAMPPROOFING – LANDSCAPE 071115 - 1

AREQUIPA PERU TEMPLE MHTN PROJECT NO 2014532.00
THE CHURCH OF JESUS CHRIST OF LATTER DAY SAINTS DESIGN
DEVELOPMENT

2.2 MISCELLANEOUS MATERIALS

A. Cut-Back Asphalt Primer: ASTM D 41.

B. Protection Course, Asphalt-Board Type: Pre-molded, 1/8-inch-thick, multi-ply, semi-rigid board

consisting of a mineral-stabilized asphalt core sandwiched between layers of asphalt-saturated
felt, and faced on 1 side with polyethylene film.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine substrates, with Installer present, for compliance with requirements for surface
smoothness and other conditions affecting performance of work.

1. Proceed with dampproofing application only after substrate construction and penetrating
work have been completed and unsatisfactory conditions have been corrected.
2. Test for surface moisture according to ASTM D 4263.

3.2 PREPARATION

A. Protection of Other Work: Mask or otherwise protect adjoining exposed surfaces from being
stained, spotted, or coated with dampproofing. Prevent dampproofing materials from entering
and clogging weep holes and drains.

B. Clean substrates of projections and substances detrimental to work; fill voids, seal joints,
and apply bond breakers if any, as recommended by prime material manufacturer.

C. Apply patching compound for filling and patching tie holes, honeycombs, reveals, and
other imperfections; cover with asphalt-coated glass fabric.

3.3 APPLICATION, GENERAL

A. Comply with manufacturer's written recommendations unless more stringent requirements

are indicated or required by Project conditions to ensure satisfactory performance of
dampproofing.

1. Apply additional coats if recommended by manufacturer or if required to achieve

coverages indicated.
2. Allow each coat of dampproofing to cure 12 hours before applying subsequent coats.
3. Allow 24 hours drying time prior to backfilling.

B. Apply dampproofing to footings as required to keep damp from rising into masonry or
other construction above.

1. Apply from finished-grade line to top of footing.

C. Apply dampproofing to provide continuous plane of protection on interior face of above-

grade, exterior concrete masonry units with brick veneers.

3.4 COLD-APPLIED, CUT-BACK ASPHALT DAMPPROOFING

A. On Concrete Foundations: Apply 2 brush or spray coats at not less than 1.25 gal./100 sq. ft. for
first coat and 1 gal./100 sq. ft. for second coat, or 1 trowel coat at not less than 4 gal./100 sq. ft..
 B. On Masonry Backup for Brick and Cast Stone Veneer Assemblies: Apply primer and 1 brush or
spray coat at not less than 1 gal./100 sq. ft..

3.5 INSTALLATION OF PROTECTION COURSE

A. Where indicated, install protection course over completed-and-cured dampproofing. Comply

with dampproofing material manufacturer's written recommendations for attaching protection
course. Support protection course with spot application of trowel-grade mastic where not
otherwise indicated.

3.6 CLEANING

A. Remove dampproofing materials from surfaces not intended to receive

dampproofing. END OF SECTION 071115

AREQUIPA PERU TEMPLE MHTN PROJECT NO 2014532.00
THE CHURCH OF JESUS CHRIST OF LATTER DAY SAINTS DESIGN DEVELOPMENT

SECTION 071414 – FLUID-APPLIED WATERPROOFING

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY

A. Section Includes for one of the following waterproofing systems provided at Contractors option
as follows:

1. Rubberized-asphalt waterproofing membrane, hot applied reinforced, vertical and

horizontal applications.
2. Drainage panels as Protection course.
3. Insulation.

B. Related Sections:

1. Other division 7 Sections for transitions required between differing products.

2. Section 079200 "Joint Sealants" for joint-sealant materials and installation.

1.3 PREINSTALLATION MEETINGS

A. Preinstallation Conference: Conduct conference at Project site.

1. Review waterproofing requirements including, but not limited to, the following:

a. Surface preparation.
b. Minimum curing period.
c. Forecasted weather conditions.
d. Special details and sheet flashings.
e. Repairs.

1.4 ACTION SUBMITTALS

A. Product Data: For each type of product indicated. Include manufacturer's written instructions
for evaluating, preparing, and treating substrate, technical data, and tested physical and
performance properties of waterproofing.

B. Shop Drawings: Show locations and extent of waterproofing. Include details for substrate joints
and cracks, sheet flashings, penetrations, inside and outside corners, tie-ins to adjoining
waterproofing, and other termination conditions.

1. Include setting drawings showing layout, sizes, sections, profiles, and joint details of
pedestal-supported concrete pavers.

FLUID-APPLIED WATERPROOFING 071414 - 1

AREQUIPA PERU TEMPLE MHTN PROJECT NO 2014532.00
THE CHURCH OF JESUS CHRIST OF LATTER DAY SAINTS DESIGN DEVELOPMENT

C. Samples: For the following products in manufacturer's standard sizes unless otherwise
indicated:

1. Flashing sheet.
2. Membrane-reinforcing fabric.
3. Insulation.
4. Drainage panel.

1.5 INFORMATIONAL SUBMITTALS

A. Qualification Data: For qualified Installer.

B. Product Test Reports: For waterproofing, based on evaluation of comprehensive tests

performed by a qualified testing agency.

C. Field quality-control reports.

D. Warranties: Sample of special warranties.

1.6 QUALITY ASSURANCE

A. Installer Qualifications: A firm that is approved or licensed by manufacturer for installation

of waterproofing required for this Project and is eligible to receive special warranties specified.

B. Source Limitations: Obtain waterproofing materials sheet flashings protection course from
single source from single manufacturer.

1.7 DELIVERY, STORAGE, AND HANDLING

A. Store liquid materials in their original undamaged containers in a clean, dry, protected location
and within the temperature range required by waterproofing manufacturer.

B. Remove and replace liquid materials that cannot be applied within their stated shelf life.

C. Protect stored materials from direct sunlight.

1.8 PROJECT CONDITIONS

A. Environmental Limitations: Apply waterproofing within the range of ambient and substrate
temperatures recommended by waterproofing manufacturer. Do not apply waterproofing to a
damp or wet substrate, or when temperature is below 0 deg F (minus 18 deg C).

1. Do not apply waterproofing in snow, rain, fog, or mist.

B. Maintain adequate ventilation during application and curing of waterproofing materials.

1.9 WARRANTY

A. Special Warranty: Manufacturer's standard form in which manufacturer agrees to repair or

replace waterproofing and sheet flashings that do not comply with requirements or that fail
to remain watertight within specified warranty period.

1. Warranty insulation will retain 80 percent of original published thermal value.

2. Warranty includes removing and reinstalling protection board, drainage panels and
insulation.
3. Warranty Period: Twenty (20) years from date of Substantial Completion.

B. Special Installer's Warranty: Owner’s Specified form signed by Installer, covering Work of this
Section, for warranty period of two years.

1. Warranty includes removing and reinstalling protection board, drainage panels, insulation.

PART 2 - PRODUCTS

2.1 WATERPROOFING MEMBRANE

A. Hot Fluid-Applied, Rubberized-Asphalt Waterproofing Membrane: Single component; 100

percent solids; hot fluid-applied, rubberized asphalt.

1. Products: Subject to compliance with requirements, provide one of the following:

a. American Hydrotech, Inc.; Monolithic Membrane 6125.

b. Barrett Company; Ram-Tough 250.
c. Henry Company; 790-11.

2.2 FLASHING SHEET MATERIALS

A. Elastomeric Flashing Sheet: 50-mil- (1.3-mm-) minimum, uncured sheet neoprene as follows:

1. Tensile Strength: 1400 psi (9.6 MPa) minimum; ASTM D 412, Die C.
2. Elongation: 300 percent minimum; ASTM D 412.
3. Tear Resistance: 125 psi (860 kPa) minimum; ASTM D 624, Die C.
4. Brittleness: Does not break at minus 30 deg F (34 deg C); ASTM D 2137.

2.3 AUXILIARY MATERIALS

A. Primer: ASTM D 41, asphaltic primer for hot applied

B. Primer: Manufacturer's standard primer, sealer, or surface conditioner; factory-formulated

acrylic latex, polyurethane, or epoxy.

C. Elastomeric Sheet: manufacturers standard 50-mil- (1.3-mm-) minimum, uncured sheet

neoprene as follows:

1. Tensile Strength: 1400 psi (9.6 MPa) minimum; ASTM D 412, Die C.
2. Elongation: 300 percent minimum; ASTM D 412.
 3. Tear Resistance: 125 psi (860 kPa) minimum; ASTM D 624, Die C.
4. Brittleness: Does not break at minus 30 deg F (34 deg C); ASTM D 2137.

5. Adhesive: Manufacturer's recommended contact adhesive for cold systems.

D. Metal Termination Bars: Manufacturer's standard, predrilled stainless-steel or aluminum

termination bars; approximately 1 by 1/8 inch (25 by 3 mm) thick; with anchors.

E. Sealants and Accessories: Manufacturer's recommended sealants and accessories.

F. Reinforcing Fabric: Manufacturer's recommended, spun-bonded polyester fabric or fiberglass

mesh for cold systems.

G. Joint Reinforcing Strip: Manufacturer's recommended fiberglass mesh or polyester fabric.

H. Joint Sealant: Multicomponent polyurethane sealant, compatible with waterproofing; ASTM C

920, Type M, Class 25 or greater; Grade NS for sloping and vertical applications and Grade P
for deck applications; Use NT exposure as recommended by manufacturer for substrate and
joint conditions.

1. Backer Rod: Closed-cell polyethylene foam.

I. Protection Course: Manufacturer's standard, 80- to 90-mil- (2.0- to 2.3-mm-) thick,

fiberglass- reinforced rubberized asphalt or modified bituminous sheet.

2.4 MOLDED-SHEET DRAINAGE PANELS

A. Nonwoven-Geotextile-Faced, Molded-Sheet Drainage Panel: Manufactured composite

subsurface drainage panels consisting of a nonwoven, needle-punched geotextile facing with
an apparent opening size not exceeding No. 70 (0.21-mm) sieve, laminated to one side
with or without a polymeric film bonded to the other side of a studded, nonbiodegradable,
molded- plastic-sheet drainage core, with a vertical flow rate of 9 to 15 gpm/ft. (112 to 188
L/min. per m).

2.5 INSULATION

A. Board Insulation: Extruded-polystyrene board insulation complying with ASTM C 578, square
edged.
1. Manufacturers: Subject to compliance with requirements, provide products by one of the
following:

a. DiversiFoam Products.
b. Dow Chemical Company (The).
c. Owens Corning.
d. Pactiv Corporation.
e. T. Clear Corporation.

2. Type IV, 25-psi (173-kPa) minimum compressive strength.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine substrates, areas, and conditions, with Installer present, for compliance with
requirements for installation tolerances and other conditions affecting performance of the Work.

1. Verify that concrete has cured and aged for minimum time period recommended by
waterproofing manufacturer.
2. Verify that substrate is visibly dry and free of moisture. Test for capillary moisture by
plastic sheet method according to ASTM D 4263.

B. Proceed with installation only after unsatisfactory conditions have been corrected.

3.2 PREPARATION

A. Clean and prepare substrates according to manufacturer's written instructions. Provide clean,
dust-free, and dry substrate for waterproofing application.

B. Mask off adjoining surfaces not receiving waterproofing to prevent spillage and overspray
affecting other construction.

C. Remove grease, oil, form-release agents, paints, curing compounds, and other penetrating
contaminants or film-forming coatings from concrete.

1. Abrasive blast clean concrete surfaces uniformly to expose top surface of fine aggregate
according to ASTM D 4259 with a self-contained, recirculating, blast-cleaning apparatus.
Remove material to provide a sound surface free of laitance, glaze, efflorescence, curing
compounds, concrete hardeners, or form-release agents. Remove remaining loose
material and clean surfaces according to ASTM D 4258.

D. Remove fins, ridges, and other projections and fill honeycomb, aggregate pockets, and
other voids.

3.3 JOINTS, CRACKS, AND TERMINATIONS

A. For hot applied systems: prepare and treat substrates to receive waterproofing membrane,
including joints and cracks, deck drains, corners, and penetrations according to manufacturer's
written instructions.

1. Rout and fill joints and cracks in substrate. Before filling, remove dust and dirt according
to ASTM D 4258.
2. Adhere strip of elastomeric sheet to substrate in a layer of hot rubberized asphalt.
Extend elastomeric sheet a minimum of 6 inches (150 mm) on each side of moving joints
and cracks or joints and cracks exceeding 1/8 inch (3 mm) thick, and beyond deck drains
and penetrations. Apply second layer of hot fluid-applied, rubberized asphalt over
elastomeric sheet.
3. Embed strip of reinforcing fabric into a layer of hot rubberized asphalt. Extend reinforcing
fabric a minimum of 6 inches (150 mm) on each side of nonmoving joints and cracks not
exceeding 1/8 inch (3 mm) thick, and beyond roof drains and penetrations.

a. Apply second layer of hot fluid-applied, rubberized asphalt over reinforcing fabric.
 B. For cold applied systems, prepare, treat, rout, and fill joints and cracks in substrate according to
waterproofing manufacturer's written instructions and to recommendations in ASTM C 898/C
898M Before coating surfaces, remove dust and dirt from joints and cracks according to
ASTM D 4258.

1. Comply with ASTM C 1193 for joint-sealant installation.

2. Apply bond breaker on sealant surface, beneath preparation strip.
3. Prime substrate along each side of joint and apply a single thickness of preparation strip
at least 6 inches (150 mm) wide along each side of joint. Apply waterproofing in two
separate applications and embed a joint reinforcing strip in the first preparation coat.

C. At expansion joints and discontinuous deck-to-wall or deck-to-deck joints, bridge joints with
elastomeric sheet extended a minimum of 6 inches (150 mm) on each side of joints and adhere
to substrates in a layer of hot rubberized asphalt for hot systems . Apply second layer of hot
fluid-applied, rubberized asphalt over elastomeric sheet.

3.4 FLASHING INSTALLATION

A. Install elastomeric flashing sheets at terminations of waterproofing membrane according to

manufacturer's written instructions.

B. Prime substrate with asphalt primer or manufacturers standard primer for cold applied systems.

C. Install elastomeric flashing sheet and adhere to deck and wall substrates in a layer of hot
rubberized asphalt or primer.

D. Extend elastomeric flashing sheet up walls or parapets a minimum of 8 inches (200 mm) above
plaza deck pavers and 6 inches (150 mm) onto deck to be waterproofed.

E. Install termination bars and mechanically fasten to top of elastomeric flashing sheet at
terminations and perimeter of roofing.

3.5 HOT APPLIED MEMBRANE APPLICATION

A. Apply primer, at manufacturer's recommended rate, 300 to 600 sf per gallon for hot
applied, over prepared substrate and allow to dry.

B. Heat and apply rubberized asphalt according to manufacturer's written instructions.

1. Heat rubberized asphalt in an oil- or air-jacketed melter with mechanical agitator

specifically designed for heating rubberized asphalt.

C. Start application with manufacturer's authorized representative present.

D. Reinforced Membrane: Apply hot rubberized asphalt to substrates and adjoining surfaces
indicated. Spread to a thickness of 90 mils (2.3 mm); embed reinforcing fabric, overlapping
sheets 2 inches (50 mm); spread another 125-mil- (3.2-mm-) thick layer to provide a
uniform, reinforced, seamless membrane 215 mils (5.5 mm) thick for horizontal hot applied
applications. For vertical hot applied applications Spread to a thickness of 90 mils (2.3
mm); embed reinforcing fabric, overlapping sheets 2 inches (50 mm); spread another 90-mil-
(3.2-mm-) thick layer to provide a uniform, reinforced, seamless membrane 180 mils thick
minimum or thicker if required for warranty requirements.
 E. Apply waterproofing over prepared joints and up wall terminations and vertical surfaces to
heights indicated or required by manufacturer.

3.6 MOLDED-SHEET DRAINAGE PANEL INSTALLATION

A. Place and secure molded-sheet drainage panels, with geotextile facing away from wall or deck
substrate according to manufacturer's written instructions. Use methods that do not penetrate
waterproofing. Lap edges and ends of geotextile to maintain continuity. Protect installed
molded-sheet drainage panels during subsequent construction.

1. For vertical applications, install board insulation before installing drainage panels.

3.7 INSULATION INSTALLATION

A. Install one or more layers of board insulation to achieve required thickness over waterproofed
surfaces. Cut and fit to within 3/4 inch (19 mm) of projections and penetrations.

B. On vertical surfaces, set insulation units into rubberized asphalt for hot systems or adhesive for
cold systems according to manufacturer's written instructions.

C. On horizontal surfaces, loosely lay insulation units according to manufacturer's written

instructions. Stagger end joints and tightly abut insulation units.

3.8 FIELD QUALITY CONTROL

A. Engage a full-time site representative qualified by waterproofing membrane manufacturer to

inspect substrate conditions; surface preparation; and application of the membrane,
flashings, protection, and drainage components; furnish daily reports to Architect.

B. Flood Testing: Flood test each deck area for leaks, according to recommendations in ASTM D
5957, after completing and protecting waterproofing but before overlaying construction is
placed. Install temporary containment assemblies, plug or dam drains, and flood with potable
water.

1. Flood to an average depth of 2-1/2 inches (65 mm) with a minimum depth of 1 inch (25
mm) and not exceeding a depth of 4 inches (100 mm). Maintain 2 inches (50 mm)
of clearance from top of sheet flashings.
2. Flood each area for 24 hours.
3. After flood testing, repair leaks, repeat flood tests, and make further repairs until
waterproofing installation is watertight.

C. Owner will engage an independent testing agency to observe flood testing and examine
underside of decks and terminations for evidence of leaks during flood testing.

3.9 CLEANING AND PROTECTION

A. Protect waterproofing from damage and wear during remainder of construction period.

B. Protect installed board insulation from damage due to UV light, harmful weather
exposures, physical abuse, and other causes. Provide temporary coverings where insulation
will be subject
 to abuse and cannot be concealed and protected by permanent construction immediately after
installation.

C. Clean spillage and soiling from adjacent construction using cleaning agents and procedures
recommended by manufacturer of affected construction.

END OF SECTION 071414

AREQUIPA PERU TEMPLE MHTN PROJECT NO 2014532.00
THE CHURCH OF JESUS CHRIST OF LATTER DAY SAINTS DESIGN DEVELOPMENT

SECTION 071901 – WATER REPELLANTS – LANDSCAPE

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY

A. Section includes penetrating water-repellent treatments for the following vertical and horizontal
surfaces:
1. Landscape components: stone paving.

1.3 PERFORMANCE REQUIREMENTS

A. General Performance: Water repellents shall meet performance requirements indicated without
failure due to defective manufacture, fabrication, or installation.
1. Water Repellents: Comply with performance requirements specified, as determined
bytesting substrate assemblies representing those indicated for this Project.

B. Water Absorption: Minimum 80 percent reduction of water absorption after 24 hours in

comparison of treated and untreated specimens.

C. Water-Vapor Transmission: Comply with one or both of the following:

1. Maximum 10 percent reduction in rate of vapor transmission in comparison of treated and
untreated specimens, according to ASTM E 96/E 96M.

D. Water Penetration and Leakage through Masonry: Minimum 90 percent reduction in

leakage rate in comparison of treated and untreated specimens, according to ASTM E 514.

E. Durability: Maximum 5 percent loss of water-repellent properties after 2500 hours of weathering
according to ASTM G 154 in comparison to water-repellent-treated specimens before
weathering.

1.4 SUBMITTALS

A. Product Data: For each type of product indicated.

B.
1. Include manufacturer's standard colors.
2. Include manufacturer's recommended number of coats for each type of substrate and
spreading rate for each separate coat.

C. Qualification Data: For qualified Applicator.

D. Product Certificates: For each type of water repellent, from manufacturer.

E. Warranty: Special warranty specified in this Section.

1.5 QUALITY ASSURANCE

A. Applicator Qualifications: An employer of workers trained and approved by manufacturer.

WATER REPELLANTS – LANDSCAPE 071901 - 1

 B. Preinstallation Conference: Conduct conference at Project site.

1.6 PROJECT CONDITIONS

A. Limitations: Proceed with application only when the following existing and forecasted weather
and substrate conditions permit water repellents to be applied according to manufacturers'
written instructions and warranty requirements:
1. Concrete surfaces and mortar have cured for not less than 28 days.
2. Building has been closed in for not less than 30 days before treating wall assemblies.
3. Ambient temperature is above 40 deg F and below 100 deg F and will remain so for 24
hours.
4. Substrate is not frozen and substrate-surface temperature is above 40 deg F and below
100 deg F.
5. Rain or snow is not predicted within 24 hours.
6. Not less than 24 hours have passed since surfaces were last wet.
7. Windy conditions do not exist that might cause water repellent to be blown onto
vegetation or surfaces not intended to be treated.
8. .

1.7 WARRANTY

A. Special Warranty: Manufacturer's standard form in which manufacturer and Applicator agree(s)
to repair or replace materials that fail to maintain water repellency specified in
"Performance Requirements" Article within specified warranty period.
1. Warranty Period: Five years from date of Substantial Completion.

PART 2 - PRODUCTS

2.1 PENETRATING WATER REPELLENTS

A. Silane/Siloxane-Blend, Penetrating Water Repellent: Clear, silane and siloxane blend with
400 g/L or less of VOCs.
1. Products: Subject to compliance with requirements, provide one of the following:
2.
a. Degussa Corporation;
b. L&M Construction Chemicals, Inc.
c. LymTal International, Inc.
d. PROSOCO, Inc.
e. Sika Corporation, Inc.
f. Tnemec Inc.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine substrates, areas, and conditions, with Applicator present, for compliance with
requirements and conditions affecting performance of the Work.
1. Verify that surfaces are clean and dry according to water-repellent manufacturer's
requirements. Check moisture content in three representative locations by method
recommended by manufacturer.
2. Inspect for previously applied treatments that may inhibit penetration or performance
of water repellents.
3. Verify that there is no efflorescence or other removable residues that would be
trapped beneath the application of water repellent.
4. Verify that required repairs are complete, cured, and dry before applying water repellent.
 B. Test pH level according to water-repellent manufacturer's written instructions to ensure
chemical bond to silica-containing or siliceous minerals.

C. Proceed with installation only after unsatisfactory conditions have been corrected.

3.2 PREPARATION

A. Cleaning: Before application of water repellent, clean substrate of substances that could impair
penetration or performance of product according to water-repellent manufacturer's written
instructions and as follows:
1. Architectural cast-in-Place Concrete: Remove oil, curing compounds, laitance, and other
substances that inhibit penetration or performance of water repellents according to
ASTM E 1857.

B. Protect adjoining work, including mortar and sealant bond surfaces, from spillage or blow-over
of water repellent. Cover adjoining and nearby surfaces of aluminum and glass if there is the
possibility of water repellent being deposited on surfaces. Cover live vegetation.

C. Coordination with Sealant Joints: Do not apply water repellent until sealants for joints adjacent
to surfaces receiving water-repellent treatment have been installed and cured.
1. Water-repellent work may precede sealant application only if sealant adhesion and
compatibility have been tested and verified using substrate, water repellent, and sealant
materials identical to those required.

3.3 APPLICATION

A. Manufacturer's Field Service: Engage a factory-authorized service representative to inspect the

substrate before application of water repellent and to instruct Applicator on the product
and application method to be used.

B. Apply a heavy-saturation coating of water repellent, on surfaces indicated for treatment, using
15 psi- pressure spray with a fan-type spray nozzle, roller, or brush to the point of
saturation. Apply coating in dual passes of uniform, overlapping strokes. Remove excess
material; do not allow material to puddle beyond saturation. Comply with manufacturer's written
instructions for application procedure unless otherwise indicated.

C. Apply a second saturation coating, repeating first application. Comply with manufacturer's
written instructions for limitations on drying time between coats and after rainstorm wetting
of surfaces between coats. Consult manufacturer's technical representative if written
instructions are not applicable to Project conditions.

3.4 FIELD QUALITY CONTROL

A. Testing of Water-Repellent Material: Owner reserves the right to invoke the following procedure
at any time and as often as Owner deems necessary during the period when water repellent is
being applied:
1. Owner will engage the services of a qualified testing agency to sample water-
repellent material being used. Samples of material delivered to Project site will be
taken, identified, sealed, and certified in presence of Contractor.
2. Testing agency will perform tests for compliance of water-repellent material with product
requirements.
3. Owner may direct Contractor to stop applying water repellents if test results show
material being used does not comply with product requirements. Contractor shall remove
noncomplying material from Project site, pay for testing, and correct deficiency of
surfaces treated with rejected materials, as approved by Architect.
 B. Coverage Test: In the presence of Architect, hose down a dry, repellent-treated surface to
verify complete and uniform product application. A change in surface color will indicate
incomplete application.
1. Notify Architect seven days in advance of the dates and times when surfaces will
be tested.
2. Reapply water repellent until coverage test indicates complete coverage.

3.5 CLEANING

A. Immediately clean water repellent from adjoining surfaces and surfaces soiled or damaged by
water-repellent application as work progresses. Correct damage to work of other trades caused
by water-repellent application, as approved by Architect.

B. Comply with manufacturer's written cleaning instructions.

END OF SECTION 071901

AREQUIPA PERU TEMPLE MHTN PROJECT NO 2014532.00
THE CHURCH OF JESUS CHRIST OF LATTER DAY SAINTS
DESIGN DEVELOPMENT

SECTION 072100– THERMAL INSULATION

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of Contract, including General and Supplementary

Conditions and Division 1 Specification Sections, apply to this Section.

1.2 SUMMARY

A. This Section includes the following:

1. Perimeter insulation.
2. Curtainwall Insulation.
3. Building insulation in batt form.

B. Related Sections: The following sections contain requirements that relate to this section:

1. Division 3 section “Cast In Place concrete” for underslab vapor retarder.

2. Division 7 Section “Firestopping” for safing insulation installed as part of
firestopping systems.
3 Division 7 Roofing Section for roof insulation specified as part of roofing construction.
4. Division 9 Section "Gypsum Board Assemblies." for sound attenuation insulation
installed as part of metal-framed wall and partition assemblies

1.3 SUBMITTALS

A. General: Submit the following in accordance with Conditions of Contract and Division 1
Specification Sections.

B. Product data for each type of insulation product specified.

C. Product test reports from and based on tests performed by qualified independent testing
laboratory evidencing compliance of insulation products with requirements including r-values,
fire performance characteristics, perm ratings, water absorption ratings, and other properties,
based on comprehensive testing of current products.

1.4 QUALITY ASSURANCE

A. Fire Performance Characteristics: Provide insulation materials identical to those whose

indicated fire performance characteristics have been determined per the ASTM test
method indicated below, by UL or other testing and inspecting organizations acceptable
to authorities having jurisdiction. Identify products with appropriate markings of applicable
testing and inspecting organization.

1. Surface Burning Characteristic: ASTM E 84.

2. Fire Resistance Ratings: ASTM E 119.
3. Combustion Characteristics: ASTM E 136.

THERMAL INSULATION 072100 - 1

 B. Single-Source Responsibility for Insulation Products: Obtain each type of building insulation from
a single source with resources to provide products of consistent quality in appearance
and physical properties without delaying progress of the Work.

1.5 DELIVERY, STORAGE, AND HANDLING

A. Protect insulation materials from physical damage and from deterioration by moisture, soiling,
and other sources. Store inside and in a dry location. Comply with manufacturer's
recommendations for handling, storage, and protection during installation.

B. Protect plastic insulation as follows:

1. Do not expose to sunlight, except to extent necessary for period of installation and
concealment.
2. Protect against ignition at all times. Do not deliver plastic insulating materials to project
site ahead of installation time.
3. Complete installation and concealment of plastic materials as rapidly as possible in
each area of construction.

PART 2 - PRODUCTS

2.1 MANUFACTURERS

A. Manufacturers: Subject to compliance with requirements, provide insulation products of one of

the following:

1. Manufacturers of Extruded Polystyrene Board Insulation:

a. Amoco Foam Products Co.

b. Dow: The Dow Chemical Company.
c. UC Industries, Inc.

2. Manufacturers of Glass Fiber Insulation:

a. CertainTeed Corp.
b. Knauf Fiber Glass GmbH.
c. Manville: Building Insulations Div., Manville Sales Corp.
d. Owens/Corning Fiberglas Corp.

2.2 INSULATING MATERIALS

A. General: Provide insulating materials that comply with requirements and with referenced
standards.

1. Preformed Units: Sizes to fit applications indicated, selected from manufacturer's

standard thicknesses, widths, and lengths.

B. Extruded Polystyrene Board Insulation: Rigid, cellular polystyrene thermal insulation with
closed-cells and integral high density skin, formed by the expansion of polystyrene base resin
in an extrusion process to comply with ASTM C 578 for type indicated; with 5-year aged r-
values of
5.4 and 5 at 40 and 75 deg F (4.4 and 23.9 deg C), respectively; and as follows:
 1. Type IV, 1.6 pcf min. density, unless otherwise indicated.

C. Faced Mineral Fiber Blanket/Batt Insulation Thermal insulation produced by combining

mineral fibers of type described below with thermosetting resins to comply with ASTM C 665
for Type III, Class A (blankets with reflective vapor-retarder membrane facing with flame
spread of 25 or less); foil-scrim-kraft or foil-scrim-polyethylene vapor-retarder membrane on
one face, and as follows:

1. Mineral Fiber Type: Fibers manufactured from glass or slag.

2. Surface Burning Characteristics: Maximum flame spread and smoke developed values
of 25 and 50, respectively.
3. Application: Thermal insulation unless otherwise indicated.

D. Mineral-Fiber-Blanket Insulation ASTM C 665, type indicated below; consisting of fibers

manufactured from glass.
1. Type II (blankets with nonreflective membrane covering), Category 1 (membrane is a
vapor retarder), Class A (membrane-faced surface with a flame-spread index of 25 or
less).
2. Vapor-Retarder Facing: ASTM C 1136, with permeance not greater than 0.02 perm (1.15
ng/Pa x s x sq. m) when tested according to ASTM E 96, Desiccant Method.
3. Composition: White polypropylene film facing and fiberglass-polyester blend fabric
backing.
4. Retainer Strips: 0.019-inch- (0.5-mm-) thick, formed, galvanized steel or PVC retainer
clips colored to match insulation facing.

2.3 SLAG-WOOL-FIBER/ROCK-WOOL-FIBER BOARD INSULATION

A. Available Manufacturers:

1. Fibrex Insulations Inc.

2. Owens Corning.
3. Thermafiber.

B. Foil-Faced, Slag-Wool-Fiber/Rock-Wool-Fiber Board Insulation: ASTM C 612; faced on 1 side

with foil-scrim or foil-scrim-polyethylene vapor retarder; with maximum flame-spread and
smoke- developed indexes of 25 and 5, respectively; and of the following nominal density and
thermal resistivity:

1. Nominal density of 4 lb/cu. ft. (64 kg/cu. m), Types IA and IB, thermal resistivity of 4 deg
F x h x sq. ft./Btu x in. at 75 deg F (27.7 K x m/W at 24 deg C).

2.4 AUXILIARY INSULATING MATERIALS

A. Adhesive for Bonding Insulation: Product with demonstrated capability to bond insulation
or mechanical anchors securely to substrates indicated without damaging or corroding
either insulation, anchors, or substrates.

2.5 INSULATION FASTENERS

A. Adhesively Attached, Spindle-Type Anchors: Plate welded to projecting spindle; capable of

holding insulation of thickness indicated securely in position indicated with self-locking washer in
place; and complying with the following requirements:
1. Available Products:
 a. AGM Industries, Inc.; Series T TACTOO Insul-Hangers.
b. Eckel Industries of Canada; Stic-Klip Type N Fasteners.
c. Gemco; Spindle Type.

2. Plate: Perforated galvanized carbon-steel sheet, 0.030 inch (0.762 mm) thick by 2 inches
(50 mm) square.
.
3. Spindle: Copper-coated, low carbon steel; fully annealed; 0.105 inch (2.67 mm) in
diameter; length to suit depth of insulation indicated.

B. Insulation-Retaining Washers: Self-locking washers formed from 0.016-inch- (0.41-mm-) thick

galvanized steel sheet, with beveled edge for increased stiffness, sized as required to
hold insulation securely in place, but not less than 1-1/2 inches (38 mm) square or in diameter.

1. Available Products:

d. AGM Industries, Inc.; RC150.

e. Gemco; Dome-Cap.

2. Protect ends with capped self-locking washers incorporating a spring steel insert to
ensure permanent retention of cap

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine substrates and conditions with Installer present, for compliance with requirements of
the Sections in which substrates and related work are specified and to determine if other
conditions affecting performance of insulation are satisfactory. Do not proceed with installation
of insulation until unsatisfactory conditions have been corrected.

3.2 PREPARATION

A. Clean substrates of substances harmful to insulations or vapor retarders, including removal of

projections that might puncture vapor retarders.

3.3 INSTALLATION, GENERAL

A. Comply with insulation manufacturer's instructions applicable to products and application

indicated. If printed instructions are not available or do not apply to project conditions, consult
manufacturer's technical representative for specific recommendations before proceeding with
installation of insulation.

B. Extend insulation full thickness as indicated to envelop entire area to be insulated. Cut and fit
tightly around obstructions, and fill voids with insulation. Remove projections that interfere
with placement.

C. Apply a single layer of insulation of required thickness, unless otherwise shown or required to
make up total thickness.
3.4 INSTALLATION OF GENERAL BUILDING INSULATION

A. Apply insulation units to substrate by method indicated, complying with manufacturer's

recommendations. If no specific method is indicated, bond units to substrate with adhesive or
use mechanical anchorage to provide permanent placement and support of units.

B. Set vapor retarder faced units with vapor retarder to warm side of construction, except
as otherwise indicated. Do not obstruct ventilation spaces, except for firestopping.

1. Tape joints and ruptures in vapor retarder, and seal each continuous area of insulation
to surrounding construction to ensure airtight installation.

3.5 INSTALLATION OF INSULATION

A. Apply insulation units to substrate by method indicated, complying with manufacturer's

recommendations. If no specific method is indicated, bond units to substrate with adhesive or
use mechanical anchorage to provide permanent placement and support of units.

3.6 INSTALLATION OF PERIMETER AND UNDERSLAB INSULATION

A. On vertical surfaces, set units in adhesive applied in accordance with manufacturer's

instructions. Use type of adhesive recommended by manufacturer of insulation.

B. On horizontal surfaces, loosely lay insulation units according to manufacturer's written

instructions. Stagger end joints and tightly abut insulation units.

C. Protect top surface of horizontal insulation from damage during concrete work by
applying protection course with joints butted.

3.7 PROTECTION

A. General: Protect installed insulation and vapor retarders from damage due to harmful weather
exposures, physical abuse, and other causes. Provide temporary coverings or enclosures where
insulation will be subject to abuse and cannot be concealed and protected by permanent
construction immediately after installation.

END OF SECTION 072100

AREQUIPA PERU TEMPLE MHTN PROJECT NO 2014532.00
THE CHURCH OF JESUS CHRIST OF LATTER DAY SAINTS DESIGN DEVELOPMENT

SECTION 075419 – POLYVINYL CHLORIDE MEMBRANE ROOFING

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 1 Specification Sections, apply to this Section.

1.2 SUMMARY

A. This Section includes the following:

1. Fully adhered PVC membrane roofing system installed over cover board and composite
concrete and steel deck.
2. Roof insulation of thicknesses to achieve R rating noted.
3. Vapor retarder – self adhering, self healing to serve as air barrier for the roof assembly.
4. Clipping of fasteners where exposed to view.

B. Roof work shall be constructed to be free of non-draining areas, with positive slope to
drain, under all conditions. Acceptance by the manufacturer of such standing water areas, low
spots, wrinkles or other conditions that retain water under their existing guidelines shall
have no bearing on the Architect or Owner’s requirements to accept conditions that are
deemed not to be acceptable. Such defects that create areas not suited to free drainage
shall be cause for rejection of the installation until corrected.

1. Factory fabricated components may require modification to achieve positive drainage, to

comply with specific project requirements for dimensional limitations and slopes to drain.

C. Related Sections include the following:

1. Division 6 Section "Rough Carpentry" for wood nailers, curbs, and blocking.
2. Division 7 Section "Building Insulation" for insulation beneath the roof deck.
3. Division 7 Section for Air Barriers.
4. Division 7 Section "Sheet Metal Flashing and Trim" for metal roof penetration
flashings, flashings, and counterflashings and rain drainage.
5. Division 7 Section "Joint Sealants."
6. Division 23 Section "Plumbing Specialties" for roof drains.

1.3 DEFINITIONS

A. Roofing Terminology: Refer to ASTM D 1079 and glossary of NRCA's "The NRCA Roofing and
Waterproofing Manual" for definition of terms related to roofing work in this Section.

B. Design Uplift Pressure: The uplift pressure, calculated according to procedures in SPRI's "Wind
Load Design Guide for Fully Adhered and Mechanically Fastened Roofing Systems,"
before multiplication by a safety factor.

C. Factored Design Uplift Pressure: The uplift pressure, calculated according to procedures in
SPRI's "Wind Load Design Guide for Fully Adhered and Mechanically Fastened Roofing
Systems," after multiplication by a safety factor.

POLYVINYL CHLORIDE MEMBRANE ROOFING 075419 - 1

1.4 PERFORMANCE REQUIREMENTS

A. General: Provide installed roofing membrane and base flashings that remain watertight; do not
permit the passage of water; that remain airtight and resist specified uplift pressures, thermally
induced movement, and exposure to weather without failure.

B. Material Compatibility: Provide roofing materials that are compatible with one another under
conditions of service and application required, as demonstrated by roofing membrane
manufacturer based on testing and field experience.

C. FMG Listing: Provide roofing membrane, base flashings, and component materials that comply
with requirements in FMG 4450 and FMG 4470 as part of a membrane roofing system and that
are listed in FMG's "Approval Guide" for Class 1 or noncombustible construction, as applicable.
Identify materials with FMG markings.

1. Fire/Windstorm Classification: Class 1A-105.

1.5 SUBMITTALS

A. Product Data: For each type of product indicated.

B. Shop Drawings: For roofing system. Include plans, elevations, sections, details, and
attachments to other Work.

1. Base flashings and membrane terminations.

2. Tapered insulation, including slopes.
3. Insulation fastening patterns.
4. Roof sump detail showing coordination with roof drains.
5. Roof membrane and vapor retarder air-tight integration with air barrier components.

C. Samples for Verification: For the following products:

1. 12-by-12-inch (300-by-300-mm) square of sheet roofing, of color specified, including

T- shaped side and end lap seam.
2. 12-by-12-inch (300-by-300-mm) square of roof insulation.
3. 12-by-12-inch (300-by-300-mm) square of vapor retarder.
4. 12-inch (300-mm) length of metal termination bars.
5. 12-inch (300-mm) length of battens.
6. Six insulation fasteners of each type, length, and finish.
7. Six roof cover fasteners of each type, length, and finish.

D. Installer Certificates: Signed by roofing system manufacturer certifying that Installer is approved,
authorized, or licensed by manufacturer to install roofing system.

E. Manufacturer Certificates: Signed by roofing manufacturer certifying that roofing system

complies with requirements specified in "Performance Requirements" Article.

1. Submit evidence of meeting performance requirements.

F. Qualification Data: For Installer and manufacturer.

G. Product Test Reports: Based on evaluation of comprehensive tests performed by manufacturer

and witnessed by a qualified testing agency, for components of roofing system.
 H. Research/Evaluation Reports: For components of membrane roofing system.

I. Maintenance Data: For roofing system to include in maintenance manuals.

J. Warranties: Special warranties specified in this Section.

K. Inspection Report: Copy of roofing system manufacturer's inspection report of completed

roofing installation.

1.6 QUALITY ASSURANCE

A. Installer Qualifications: A qualified firm that is approved, authorized, or licensed by roofing

system manufacturer to install manufacturer's product and that is eligible to receive
manufacturer's warranty prior to receipt of bids.
1. A minimum of two years experience is required on similar sized projects.

B. Testing Agency Qualifications: An independent testing agency with the experience and
capability to conduct the testing indicated, as documented according to ASTM E 548.

C. Source Limitations: Obtain components for membrane roofing system from or approved by
roofing membrane manufacturer.

D. Fire-Test-Response Characteristics: Provide membrane roofing materials with the fire-test-

response characteristics indicated as determined by testing identical products per test method
below by UL, FMG, or another testing and inspecting agency acceptable to authorities
having jurisdiction. Materials shall be identified with appropriate markings of applicable
testing and inspecting agency.

1. Exterior Fire-Test Exposure: Class A; ASTM E 108, for application and roof slopes
indicated.
2. Fire-Resistance Ratings: ASTM E 119, for fire-resistance-rated roof assemblies of which
roofing system is a part.

E. Preliminary Roofing Conference: Before starting roof deck construction, conduct conference at
Project site. Comply with requirements for preinstallation conferences in Division 1 Section
"Project Management and Coordination." Review methods and procedures related to roof deck
construction and roofing system including, but not limited to, the following:

1. Meet with Owner, Architect, Owner's insurer if applicable, testing and inspecting agency
representative, roofing Installer, roofing system manufacturer's representative, deck
Installer, and installers whose work interfaces with or affects roofing including installers of
roof accessories and roof-mounted equipment.
2. Review methods and procedures related to roofing installation, including manufacturer's
written instructions.
3. Review and finalize construction schedule and verify availability of materials,
Installer's personnel, equipment, and facilities needed to make progress and avoid
delays.
4. Examine deck substrate conditions and finishes for compliance with requirements,
including flatness and fastening.
5. Review conditions of sloped deck and tapered insulation to confirm that no flat spots exist
in the installation.
6. Review structural loading limitations of roof deck during and after roofing.
7. Review base flashings, special roofing details, roof drainage, roof penetrations,
equipment curbs, and condition of other construction that will affect roofing system.
 8. Review requirements to maintain a continuous plane of air barrier tightness at transitions
between roofing and adjacent components.
9. Review governing regulations and requirements for insurance and certificates if
applicable.
10. Review temporary protection requirements for roofing system during and after installation.
11. Review roof observation and repair procedures after roofing installation.

F. Preinstallation Conference: Conduct conference at Project site. Comply with requirements in

Division 1 Section "Project Management and Coordination." Review methods and procedures
related to roofing system including, but not limited to, the following:

1. Meet with Owner, Architect, Owner's insurer if applicable, testing and inspecting agency
representative, roofing Installer, roofing system manufacturer's representative, deck
Installer, and installers whose work interfaces with or affects roofing including installers of
roof accessories and roof-mounted equipment.
2. Review methods and procedures related to roofing installation, including manufacturer's
written instructions.
3. Review and finalize construction schedule and verify availability of materials,
Installer's personnel, equipment, and facilities needed to make progress and avoid
delays.
4. Examine deck substrate conditions and finishes for compliance with requirements,
including flatness and fastening.
5. Review structural loading limitations of roof deck during and after roofing.
6. Review base flashings, special roofing details, roof drainage, roof penetrations,
equipment curbs, and condition of other construction that will affect roofing system.
7. Review governing regulations and requirements for insurance and certificates if
applicable.
8. Review temporary protection requirements for roofing system during and after installation.
9. Review roof observation and repair procedures after roofing installation.

1.7 DELIVERY, STORAGE, AND HANDLING

A. Deliver roofing materials to Project site in original containers with seals unbroken and
labeled with manufacturer's name, product brand name and type, date of manufacture, and
directions for storing and mixing with other components.

B. Store liquid materials in their original undamaged containers in a clean, dry, protected location
and within the temperature range required by roofing system manufacturer. Protect stored
liquid material from direct sunlight.

1. Discard and legally dispose of liquid material that cannot be applied within its stated shelf
life.

C. Protect roof insulation materials from physical damage and from deterioration by sunlight,
moisture, soiling, and other sources. Store in a dry location. Comply with insulation
manufacturer's written instructions for handling, storing, and protecting during installation.

D. Handle and store roofing materials and place equipment in a manner to avoid permanent
deflection of deck.
1.8 PROJECT CONDITIONS

A. Weather Limitations: Proceed with installation only when existing and forecasted weather
conditions permit roofing system to be installed according to manufacturer's written instructions
and warranty requirements.

1.9 WARRANTY

A. Special Warranty: Manufacturer’s form without monetary limitation (NDL) where manufacturer
agrees to repair or replace components of membrane roofing system that fail in materials
or workmanship within specified warranty period. Failure includes roof leaks.

1. Warranty Period: 30 years from date of Substantial Completion, with 90 mph Wind
rating.

B. Special Project Warranty: Submit roofing Installer's warranty, signed by Installer, covering Work
of this Section, including all components of membrane roofing system such as roofing
membrane, base flashing, roof insulation, fasteners, cover boards, substrate boards, vapor
retarders and walkway products, for the following warranty period:

1. Warranty Period: FIVE years from date of Substantial Completion.

PART 2 - PRODUCTS

2.1 MANUFACTURERS

A. In other Part 2 articles where titles below introduce lists, the following requirements apply
for product selection:
1. Manufacturers: Subject to compliance with requirements, provide products by the
manufacturers specified.

2.2 ROOFING MEMBRANE

A. Fabric-Reinforced PVC Sheet: Uniform, flexible sheet reinforced internally and as follows:

Manufacturers:

Carlisle SureFlex FRS PVC-Glass Reinforced.

Sarnafil, Inc G-410 PVC.
Versico Versiflex. FRS PVC-Glass Reinforced.

Thickness: 80 mils, nominal thickness.

Exposed Face Color: White.

AREQUIPA PERU TEMPLE MHTN PROJECT NO 2014532.00
THE CHURCH OF JESUS CHRIST OF LATTER DAY SAINTS DESIGN DEVELOPMENT

2.3 COVER BOARDS

A. Cover Board: ASTM C 1177/C 1177M, glass-mat, water-resistant gypsum substrate, Type X,
5/8 inch (16 mm) thick.

1. Products: Subject to compliance with requirements including approval by the

manufacturer for Warranty, available products that may be incorporated into the
Work include, but are not limited to, the following:

a. Georgia-Pacific Corporation; Dens Deck.

b. USG Securock Gypsum Fiber Roof Board.

B. Fasteners: Factory-coated steel fasteners and metal or plastic plates complying with corrosion-
resistance provisions in FM Approvals 4470, designed for fastening substrate board to roof
deck.

2.4 AUXILIARY MATERIALS

A. General: Auxiliary materials recommended by roofing system manufacturer for intended use
and compatible with membrane roofing.

1. Liquid-type auxiliary materials shall meet VOC limits of authorities having jurisdiction.

B. Sheet Flashing: Manufacturer's standard sheet flashing of same material, type, reinforcement,
thickness, and color as sheet membrane.

C. Sheet Flashing: Manufacturer's standard unreinforced thermoplastic polyolefin sheet flashing,

55 mils (1.4 mm) thick, minimum, of same color as sheet membrane.

D. Bonding Adhesive: Manufacturer's standard bonding adhesive for membrane, and solvent-
based bonding adhesive for base flashings.Solvenrt based or low rise as approved by
manufacturer.

E. Metal Termination Bars: Manufacturer's standard predrilled stainless-steel or aluminum bars,

approximately 1 by 1/8 inch (25 by 3 mm) thick; with anchors.

F. Metal Battens: Manufacturer's standard aluminum-zinc-alloy-coated or zinc-coated steel sheet,

approximately 1 inch (25 mm) wide by 0.05 inch (1.3 mm) thick, prepunched.

G. Fasteners: Factory-coated steel fasteners and metal or plastic plates meeting corrosion-
resistance provisions in FMG 4470, designed for fastening membrane to substrate, and
acceptable to membrane roofing system manufacturer.

H. Miscellaneous Accessories: Provide pourable sealers, preformed cone and vent sheet
flashings, preformed inside and outside corner sheet flashings, T-joint covers, termination
reglets, cover strips, and other accessories.

2.5 ROOF INSULATION

A. General: Provide preformed roof insulation boards that comply with requirements and
referenced standards, selected from manufacturer's standard sizes and of thicknesses
indicated.
 B. Polyisocyanurate Board Insulation: ASTM C 1289, Type II, felt or glass-fiber mat facer on both
major surfaces.

1. Available Manufacturers include the following:

a. AlliedSignal Inc.; Commercial Roofing Systems.

b. Atlas Roofing Corporation.
c. Carlisle SynTec Incorporated.
d. Firestone Building Products Company.
e. Hunter Panels, LLC.
f. Johns Manville International, Inc.

C. Tapered Insulation: Provide factory-tapered insulation boards fabricated to a minimum slope of

1/4 inch per 12 inches or as required to provide a minimum slope of 1/4 inch per 12 inches in
valleys. EPS is NOT permitted in sloped applications.

D. Provide preformed saddles, crickets, tapered edge strips, and other insulation shapes
where indicated for sloping to drain. Fabricate to slopes indicated.

2.6 INSULATION ACCESSORIES

A. General: Roof insulation accessories recommended by insulation manufacturer for intended

use and compatible with membrane roofing.

B. Fasteners: Factory-coated steel fasteners and metal or plastic plates meeting corrosion-
resistance provisions in FMG 4470, designed for fastening roof insulation to substrate, and
acceptable to roofing system manufacturer.

C. Bead-Applied Insulation Adhesive: Insulation manufacturer's recommended bead-applied, low-

rise, one- or multicomponent urethane adhesive formulated to attach roof insulation to substrate
or to another insulation layer.

D. Full-Spread Applied Insulation Adhesive: Insulation manufacturer's recommended spray-

applied, low-rise, two-component urethane adhesive formulated to attach roof insulation to
substrate or to another insulation layer.

E. Protection Mat: Woven or nonwoven polypropylene, polyolefin, or polyester fabric mat,

water permeable and resistant to ultraviolet degradation, type and weight as recommended by
roofing system manufacturer for application.

F. Slip Sheet: Manufacturer's recommended slip sheet, of type required for application to separate
membrane from insulating substrate.

2.7 VAPOR RETARDER

A. Self-adhering sheet, low density polyethylene: 32 mil thickness minimum, with maximum
permeance rating of 0.19 perm.

B. Primers and sealants recommended by manufacturer for substrate and conditions.

2.8 WALKWAYS

A. Flexible Walkways: Factory-formed, nonporous, heavy-duty, slip-resisting, open-grid, surface-

textured, flexible PVC walkway mat, approximately 9/16 inch thick, and acceptable to
membrane roofing system manufacturer.

1. Color: White.
2. Size: 24 x 24 squares or 3 foot wide by 33 feet long rolls.
3. Design Standard: Design Standards are used to establish a level of quality for the work.
Premium products equal in quality of acceptable manufacturers may be used. The use of
a Design Standard is not to be construed as a limit of competition or a constraint of trade.

a. Sarnafil Crossgrip Walkway Mat.

b. Carlisle ECO NOVA.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine substrates, areas, and conditions, with Installer present, for compliance with the
following requirements and other conditions affecting performance of roofing system:

1. Verify that roof openings and penetrations are in place and set and braced and that roof
drains are securely clamped in place.
2. Verify that pressure treated wood blocking, curbs, and nailers are securely anchored
to roof deck at penetrations and terminations and that nailers match thicknesses of
insulation.
3. Verify that surface plane flatness and fastening of steel roof deck comply with
requirements in Division 5 Section "Steel Deck."
4. Verify that membrane shows no signs of abrasion, discoloration, or defects.
5. Proceed with installation only after unsatisfactory conditions have been corrected.

3.2 PREPARATION

A. Clean substrate of dust, debris, moisture, and other substances detrimental to roofing
installation according to roofing system manufacturer's written instructions. Remove sharp
projections.

B. Prevent materials from entering and clogging roof drains and conductors and from spilling
or migrating onto surfaces of other construction. Remove roof-drain plugs when no work is
taking place or when rain is forecast.

C. Complete terminations and base flashings and provide temporary seals to prevent water
from entering completed sections of roofing system at the end of the workday or when
rain is forecast. Remove and discard temporary seals before beginning work on adjoining
roofing.

D. Employ roofer for repairing existing roof membrane as approved by the manufacturer,
where warranties are still in effect for the existing assembly.
AREQUIPA PERU TEMPLE MHTN PROJECT NO 2014532.00
THE CHURCH OF JESUS CHRIST OF LATTER DAY SAINTS DESIGN DEVELOPMENT

3.3 VAPOR-RETARDER INSTALLATION

A. Self-Adhering Sheet: Place self-adhering sheet in a single layer over area to receive vapor
retarder, side lapping each sheet a minimum of 3 inches. Stagger end laps a minimum of 12
inches.

1. Continuously seal side and end laps by rolling with roller to ensure adhesion to deck.

B. Completely seal vapor retarder at terminations, obstructions, and penetrations to prevent

air movement into membrane roofing system and provide air-tight performance.

C. Extend vapor retarder up parapets and lap behind PVC base flashing. Fully adhere to parapet.

D. Repair all punctures and tears, prior to covering retarder sheet with insulation.

3.4 INSULATION INSTALLATION

A. Coordinate installing membrane roofing system components so insulation is not exposed to

precipitation or left exposed at the end of the workday.

B. Comply with membrane roofing system manufacturer's written instructions for installing roof
insulation.

C. Install tapered insulation under area of roofing to conform to slopes indicated.

D. Install MULTIPLE layers of insulation, joints staggered, under area of roofing to achieve
required thickness.

E. Trim surface of insulation where necessary at roof drains so completed surface is flush
and does not restrict flow of water.

F. Field rim factory formed units where required to provide slopes in crickets and drains.

G. Install insulation with long joints of insulation in a continuous straight line with end joints
staggered between rows, abutting edges and ends between boards. Fill gaps exceeding
1/4 inch (6 mm) with insulation.

1. Cut and fit insulation within 1/4 inch (6 mm) of nailers, projections, and penetrations.

H. Adhered Insulation: Install each layer of insulation and adhere to substrate as follows:

1. Prime surface of concrete deck with asphalt primer at rate of 3/4 gal./100 sq. ft. (0.3
L/sq. m) and allow primer to dry.
2. Set each layer of insulation in ribbons of bead-applied insulation adhesive or a uniform
coverage of full-spread insulation adhesive, firmly pressing and maintaining insulation in
place.

I. Install cover boards over insulation with long joints in continuous straight lines with end
joints staggered between rows. Offset joints of insulation below a minimum of 24 inches in
each direction. Loosely butt cover boards together.

1. Fasten cover boards according to requirements in FM Approvals' "RoofNav" for specified

Windstorm Resistance Classification.
AREQUIPA PERU TEMPLE MHTN PROJECT NO 2014532.00
THE CHURCH OF JESUS CHRIST OF LATTER DAY SAINTS DESIGN DEVELOPMENT

3.5 ROOFING MEMBRANE INSTALLATION

A. Adhere membrane roofing over area to receive roofing and install according to membrane
roofing system manufacturer's written instructions.

1. Install sheet according to ASTM D 5036.

B. Start installation of roofing membrane in presence of membrane roofing system manufacturer's

technical personnel.

C. Accurately align roofing membranes and maintain uniform side and end laps of minimum
dimensions required by manufacturer. Stagger end laps.

D. Bonding Adhesive: Apply to substrate and underside of membrane roofing at rate required by
manufacturer and allow to partially dry before installing membrane roofing. Do not apply to
splice area of membrane roofing.

E. In addition to adhering, mechanically fasten membrane roofing securely at terminations,

penetrations, and perimeter of roofing.

F. Apply roofing membrane with side laps shingled with slope of roof deck where possible.

G. Seams: Clean seam areas, overlap roofing membrane, and hot-air weld side and end laps of
roofing membrane and sheet flashings according to manufacturer's written instructions to
ensure a watertight seam installation.

1. Test lap edges with probe to verify seam weld continuity. Apply lap sealant to seal cut
edges of roofing membrane.
2. Verify field strength of seams a minimum of twice daily and repair seam sample areas.
3. Repair tears, voids, and lapped seams in roofing that do not meet requirements.

H. Spread sealant or mastic bed over deck drain flange at deck drains and securely seal
roofing membrane in place with clamping ring. Add second ply where drains are set after
membrane installation.

3.6 BASE FLASHING INSTALLATION

A. Install sheet flashings and preformed flashing accessories and adhere to substrates according
to membrane roofing system manufacturer's written instructions.

B. Apply bonding adhesive to substrate and underside of sheet flashing at required rate and allow
to partially dry. Do not apply bonding adhesive to seam area of flashing.

C. Flash penetrations and field-formed inside and outside corners with sheet flashing.

D. Clean seam areas and overlap and firmly roll sheet flashings into the adhesive. Weld side and
end laps to ensure a watertight seam installation.

E. Terminate and seal top of sheet flashings and mechanically anchor to substrate through
termination bars.

POLYVINYL CHLORIDE MEMBRANE ROOFING 075419 - 10

3.7 WALKWAY MAT INSTALLATION

A. Flexible Walkway Mats: Install walkway mat products in locations indicated, from hatches to
roof-top mounted equipment. Secure to roofing membrane according to roofing system and
walkway mat manufacturers’ written instructions.

3.8 FIELD QUALITY CONTROL

A. Field Inspection:
1. Before Manufacturer's inspection for warranty, Installer must perform pre-inspection to
review work and to verify flashing has been completed as well as application of
caulking.
2. Final Roof Inspection:
a. Arrange for Roofing Membrane Manufacturer's technical personnel to inspect
roofing installation on completion.
3. Upon completion of roof inspection, provide certification that installation has
been performed in accordance with Contract Document and Roofing
Manufacturer requirements.

B. Non-Conforming Work:
1. Correct all work not in compliance to Contract Documents at no additional cost to Owner.
a. Repair or remove and replace components of membrane roofing system
where inspections indicate that they do not comply with specified
requirements.
b. Replace contaminated membrane.
2. Additional inspections will be performed to determine compliance of replaced
or additional work with specified requirements at no additional cost to Owner.
3. Repair landscaped areas damaged by construction activities at no additional cost
to Owner.

C. Final Roof Inspection: Arrange for roofing system manufacturer's technical personnel to submit
report to Architect.

1. Notify Architect or Owner 48 hours in advance of date and time of inspection.

3.9 PROTECTING AND CLEANING

A. Protect membrane roofing system from damage and wear during remainder of construction
period. When remaining construction will not affect or endanger roofing, inspect roofing for
deterioration and damage, describing its nature and extent in a written report, with copies
to Architect and Owner.

B. Correct deficiencies in or remove membrane roofing system that does not comply with
requirements, repair substrates, and repair or reinstall membrane roofing system to a condition
free of damage and deterioration at time of Substantial Completion and according to warranty
requirements.

C. Clean overspray and spillage from adjacent construction using cleaning agents and procedures
recommended by manufacturer of affected construction.

END OF SECTION

STEAM AND CONDENSATE PIPING, VALVES & 232200 - 1

SPECIALTIES