Scribd
Upload
57 views10 pages

Fourth Project-Static 2-1

1. The document summarizes a static simulation of a fourth project model composed of a single alloy steel ball bearing a torque load of 600 N.m. 2. The simulation found a maximum von Mises stress of 8.186e+10 N/m^2 and a maximum resultant displacement of 1.458e+10 mm under the applied load. 3. The summary provides key details about the model, study properties, materials, loads, mesh, and results of the static simulation.

Uploaded by

nabaz muhamad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
57 views10 pages

Fourth Project-Static 2-1

1. The document summarizes a static simulation of a fourth project model composed of a single alloy steel ball bearing a torque load of 600 N.m. 2. The simulation found a maximum von Mises stress of 8.186e+10 N/m^2 and a maximum resultant displacement of 1.458e+10 mm under the applied load. 3. The summary provides key details about the model, study properties, materials, loads, mesh, and results of the static simulation.

Uploaded by

nabaz muhamad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 10

Simulation of fourth

project
Date: Sunday, November 01, 2020
Designer: Solidworks
Study name: Static 2
Analysis type: Static

Table of Contents
Description...........................................1
Assumptions..........................................2
Model Information..................................2
Study Properties.....................................3
Units..................................................3
Material Properties.................................4
Loads and Fixtures..................................4
Connector Definitions..............................5
Contact Information................................5
Description Mesh information....................................6
No Data Sensor Details........................................7
Resultant Forces....................................7
Beams.................................................7
Study Results........................................8
Conclusion..........................................10

Analyzed with SOLIDWORKS Simulation Simulation of fourth project 1


Assumptions

Model Information

Model name: fourth project


Current Configuration: PreviewCfg
Solid Bodies
Document Name and Document Path/Date
Treated As Volumetric Properties
Reference Modified
BallsDetailed
Mass:0.00168 kg
Volume:2.18182e-07 m^3
E:\fourth project.SLDPRT
Solid Body Density:7700 kg/m^3
Nov 1 17:14:21 2020
Weight:0.016464 N

Analyzed with SOLIDWORKS Simulation Simulation of fourth project 2


Study Properties
Study name Static 2
Analysis type Static
Mesh type Solid Mesh
Thermal Effect: On
Thermal option Include temperature loads
Zero strain temperature 298 Kelvin
Include fluid pressure effects from SOLIDWORKS Off
Flow Simulation
Solver type FFEPlus
Inplane Effect: Off
Soft Spring: Off
Inertial Relief: Off
Incompatible bonding options Automatic
Large displacement Off
Compute free body forces On
Friction Off
Use Adaptive Method: Off
Result folder SOLIDWORKS document (E:)

Units
Unit system: SI (MKS)
Length/Displacement mm
Temperature Kelvin
Angular velocity Rad/sec
Pressure/Stress N/m^2

Analyzed with SOLIDWORKS Simulation Simulation of fourth project 3


Material Properties
Model Reference Properties Components
Name: Alloy Steel SolidBody 1(BallsDetailed)
Model type: Linear Elastic Isotropic (fourth project)
Default failure Max von Mises Stress
criterion:
Yield strength: 6.20422e+08 N/m^2
Tensile strength: 7.23826e+08 N/m^2
Elastic modulus: 2.1e+11 N/m^2
Poisson's ratio: 0.28
Mass density: 7700 kg/m^3
Shear modulus: 7.9e+10 N/m^2
Thermal expansion 1.3e-05 /Kelvin
coefficient:

Curve Data:N/A

Loads and Fixtures

Load name Load Image Load Details


Entities: 1 face(s)
Reference: Axis3
Type: Apply torque
Torque-1 Value: 600 N.m

Analyzed with SOLIDWORKS Simulation Simulation of fourth project 4


Connector Definitions

Pin/Bolt/Bearing Connector
Model Reference Connector Details Strength Details
Entities: 1 face(s)
Type: Bearing

No Data

Bearing Support-1
Connector Forces
Type X-Component Y-Component Z-Component Resultant
Axial Force (N) 210.97 0 0 210.97
Shear Force (N) 0 -21144 -42490 47461
Bending moment (N.m) 0 0 0 0

Contact Information
No Data

Analyzed with SOLIDWORKS Simulation Simulation of fourth project 5


Mesh information
Mesh type Solid Mesh
Mesher Used: Standard mesh
Automatic Transition: Off
Include Mesh Auto Loops: Off
Jacobian points 4 Points
Element Size 0.602321 mm
Tolerance 0.0301161 mm
Mesh Quality Plot High

Mesh information - Details


Total Nodes 19345
Total Elements 11091
Maximum Aspect Ratio 13.172
% of elements with Aspect Ratio < 3 94.5
% of elements with Aspect Ratio > 10 0.0451
% of distorted elements(Jacobian) 0
Time to complete mesh(hh;mm;ss): 00:00:04
Computer name:

Analyzed with SOLIDWORKS Simulation Simulation of fourth project 6


Sensor Details
No Data

Resultant Forces
Reaction forces
Selection set Units Sum X Sum Y Sum Z Resultant
Entire Model N 0 0 0 1e-33

Reaction Moments
Selection set Units Sum X Sum Y Sum Z Resultant
Entire Model N.m 0 0 0 0

Beams
No Data

Analyzed with SOLIDWORKS Simulation Simulation of fourth project 7


Study Results

Name Type Min Max


Stress1 VON: von Mises Stress 1.285e+08 N/m^2 8.186e+10 N/m^2
Node: 1242 Node: 19099

fourth project-Static 2-Stress-Stress1

Name Type Min Max


Displacement1 URES: Resultant Displacement 7.267e+09 mm 1.458e+10 mm
Node: 993 Node: 792

Analyzed with SOLIDWORKS Simulation Simulation of fourth project 8


Name Type Min Max

fourth project-Static 2-Displacement-Displacement1

Name Type Min Max


Strain1 ESTRN: Equivalent Strain 6.015e-04 2.156e-01
Element: 1691 Element: 3841

fourth project-Static 2-Strain-Strain1

Analyzed with SOLIDWORKS Simulation Simulation of fourth project 9


Conclusion

Analyzed with SOLIDWORKS Simulation Simulation of fourth project 10

You might also like