Scribd
Upload
69 views

Raspberry Pi Begginer Guide Part 3

This document provides instructions for setting up the basic hardware components needed to get started with a Raspberry Pi. These include a microSD card with the NOOBS operating system installed, a USB keyboard and mouse, an HDMI cable to connect to a display, and a USB power supply. It also describes how to assemble the Raspberry Pi into an optional protective case before connecting all the components: the microSD card, keyboard and mouse via USB, display via HDMI, an optional Ethernet network cable, and finally connecting the USB power supply to turn the device on.

Uploaded by

New Register
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
69 views

Raspberry Pi Begginer Guide Part 3

This document provides instructions for setting up the basic hardware components needed to get started with a Raspberry Pi. These include a microSD card with the NOOBS operating system installed, a USB keyboard and mouse, an HDMI cable to connect to a display, and a USB power supply. It also describes how to assemble the Raspberry Pi into an optional protective case before connecting all the components: the microSD card, keyboard and mouse via USB, display via HDMI, an optional Ethernet network cable, and finally connecting the USB power supply to turn the device on.

Uploaded by

New Register
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

THE OFFICIAL RASPBERRY PI BEGINNER’S GUIDE

If you don’t have the Raspberry Pi Starter Kit, then in addition to the Raspberry Pi 3 Model B+
you’ll need:

n USB power supply – A power supply rated


at 2.5 amps (2.5A) or 12.5 watts (12.5W)
and with a micro USB connector. The
Official Raspberry Pi Power Supply is the
recommended choice, as it can cope with
the quickly switching power demands of
the Raspberry Pi.

n microSD card with NOOBS – The microSD card


acts as the Raspberry Pi’s permanent storage;
all the files you create and software you install,
along with the operating system itself, are
stored on the microSD card. An 8GB card will
get you started, though a 16GB card offers more
room to grow. Using a card with NOOBS, the
New Out-Of-Box Software, pre-installed will save
you some time; otherwise see Appendix A for
instructions on installing NOOBS on a blank
microSD card.

n USB keyboard and mouse – The keyboard


and mouse allow you to control the Raspberry
Pi. Almost any wired or wireless keyboard and
mouse with a USB connector will work with
the Raspberry Pi, though some ‘gaming’ style
keyboards with colourful lights may draw too
much power to be used reliably.

n HDMI Cable – The HDMI cable carries sound
and pictures from the Raspberry Pi to your TV
or monitor. There’s no need to spend a lot of
money on an HDMI cable. If you are using a
computer monitor without an HDMI socket, you
can buy HDMI to DVI-D, DisplayPort, or VGA
adapters; if you want to connect your Raspberry
Pi to an older TV which uses composite video or
has a SCART socket, use a 3.5 mm tip-ring-ring-
sleeve (TRRS) audio/video cable.

Chapter 2 Getting started with your Raspberry Pi 21


The Raspberry Pi is safe to use without a case, providing you don’t place it on a metal
surface which could conduct electricity and cause a short-circuit. An optional case, however,
can provide additional protection; the Starter Kit includes the Official Raspberry Pi Case, while
third-party cases are available from all good stockists.
If you want to use the Raspberry Pi on a wired network, rather than a wireless (WiFi) network,
you’ll also need a network cable. This should be connected at one end to your network’s switch or
router. If you’re planning to use the Raspberry Pi’s built-in wireless radio, you won’t need a cable;
you will, however, need to know the name and key or passphrase for your wireless network.

Setting up the hardware


Begin by unpacking your Raspberry Pi from its box. The Raspberry Pi is a robust piece of
hardware, but that doesn’t mean it’s indestructible: try to get into the habit of holding the board
by the edges, rather than on its flat sides, and be extra careful around the raised metal pins. If
these pins are bent, at best it’ll make using add-on boards and other extra hardware difficult
and, at worst, can cause a short-circuit that will damage the Raspberry Pi.
If you haven’t done so already, have a look at Chapter 1, Getting to know your Raspberry Pi,
for details on exactly where the various ports are and what they do.

Assembling the case


If you’re installing your Pi in a case, it should be your first step. If you’re using the Official
Raspberry Pi Case, begin by splitting it into its five individual pieces: the red base, two white
sides, red upper, and white lid.

1 Take the base and hold it so that the raised end is to your left and the lower end to your right.

22 THE OFFICIAL RASPBERRY PI BEGINNER'S GUIDE


THE OFFICIAL RASPBERRY PI BEGINNER’S GUIDE


2 Holding the Pi by its USB and Ethernet ports, with the GPIO header to the top, slot the left-
hand side into the case at an angle, then gently lower the right-hand side down so it sits flat.


3 Take the two white side pieces and find the one with the cut-outs for the power connector,
HDMI port, and 3.5 mm AV jack. Line it up with the ports on the Raspberry Pi and gently push
it home until you hear a click.

Chapter 2 Getting started with your Raspberry Pi 23


4 Take the solid white side piece and click it in to the GPIO header side of the case.


5 Take the red plastic upper piece and place the two clips at the left into the matching
holes on the left of the base, above the microSD card slot. When they’re in place, push the
right‑hand side (above the USB ports) down until you hear a click.

24 THE OFFICIAL RASPBERRY PI BEGINNER'S GUIDE


THE OFFICIAL RASPBERRY PI BEGINNER’S GUIDE


6 Finally, take the white lid and hold it so that the Raspberry Pi logo is to your right and the
small raised clips on its underside are lined up with the hole on the top of the case, then
gently push it down until you hear a click. Your case is now fully built.

Chapter 2 Getting started with your Raspberry Pi 25


Connecting the microSD card
To install the microSD card, which is the Raspberry Pi’s storage, turn the Raspberry Pi over and
slide the card into the microSD slot with the label facing away from the Pi. It can only go in one
way, and should slide home without too much pressure.

The microSD card will slide into the connector, then stop without a click.

If you want to remove it again in the future, simply grip the end of the card and pull it gently
out. If you’re using an older model of Raspberry Pi, you’ll need to give the card a gentle push
first to unlock it; this isn’t necessary with a Raspberry Pi 3 or newer.

26 THE OFFICIAL RASPBERRY PI BEGINNER'S GUIDE


THE OFFICIAL RASPBERRY PI BEGINNER’S GUIDE

Connecting a keyboard and mouse


Connect the keyboard’s USB cable to any of the four USB ports on the Raspberry Pi. When the
keyboard is connected, simply do the same for the mouse.

The USB connectors for the keyboard and mouse should slide home without too much
pressure; if you’re having to force the connector in, there’s something wrong. Check that the
USB connector is the right way up!

KEYBOARD & MOUSE


The keyboard and mouse act as your main means of telling the
Raspberry Pi what to do; in computing, these are known as input
devices, in contrast with the display which is an output device.

Chapter 2 Getting started with your Raspberry Pi 27


Connecting a display
Take the HDMI cable and connect one end – it doesn’t matter which – to your Raspberry Pi
and the other end to your display. If your display has more than one HDMI port, look for a port
number next to the connector itself; you’ll need to switch the TV to this input to see the Pi’s
display. If you can’t see a port number, don’t worry: you can simply switch through each input
in turn until you find the Pi.

TV CONNECTION
If your TV or monitor doesn’t have an HDMI connector, that doesn’t
mean you can’t use the Raspberry Pi. Adapter cables, available from
any electronics stockist, will allow you to convert the HDMI port on the
Raspberry Pi to DVI-D, DisplayPort, or VGA for use with older computer
monitors; these are simply connected to the Pi’s HDMI port, then a
suitable cable used to connect the adapter cable to the monitor. If
your TV has only a composite video or SCART input, you can purchase
3.5 mm tip-ring-ring-sleeve (TRRS) adapter cables and composite-to-
SCART adapters which connect to the 3.5 mm AV jack.

28 THE OFFICIAL RASPBERRY PI BEGINNER'S GUIDE


THE OFFICIAL RASPBERRY PI BEGINNER’S GUIDE

Connecting a network cable (optional)


To connect your Raspberry Pi to a wired network, take a network cable – known as an Ethernet
cable – and push it into the Pi’s Ethernet port, with the plastic clip facing downwards, until you
hear a click. If you need to remove the cable, just squeeze the plastic clip inwards towards the
plug and gently slide the cable free again.

The other end of your network cable should be connected to any free port on your network hub,
switch, or router in the same way.

Chapter 2 Getting started with your Raspberry Pi 29


Connecting a power supply
Connecting the Raspberry Pi to a power supply is the very last step in the hardware setup
process, and it’s one you should do only when you’re ready to set up its software: the
Raspberry Pi does not have a power switch and will turn on as soon as it is connected to a live
power supply.
First, connect the micro USB end of the power supply cable to the micro USB power
connector on the Raspberry Pi. It can only go in one way, with the narrow part of the connector
facing downwards, and should slide home gently.

POWER SUPPLY
If you’re using the Official Raspberry Pi Power Supply, you’ll see it
comes with multiple mains connectors suitable for the sockets of
various countries; find the one that matches your country’s socket
type, then slide it onto the power supply body until you hear a click.

Finally, connect the power supply to a mains socket and switch the socket on; the Raspberry
Pi will immediately start running.
Congratulations: you’ve put your Raspberry Pi together!

30 THE OFFICIAL RASPBERRY PI BEGINNER'S GUIDE

You might also like