Release Notes for Unified Contact Center Express Solution Release

11.0(1)
First Published: August 27, 2015

Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version
of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.
CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: http://
www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (1110R)

© 2015 Cisco Systems, Inc. All rights reserved.

 CONTENTS

CHAPTER 1 Introduction 1
Release Notes for Contact Center Solutions 1

CHAPTER 2 Cisco Unified Contact Center Express 3

New and Updated Features 3
New Features 3
Email Enhancement 3
Finesse IP Phone Agent 3
Outbound Enhancement 3
Standalone Unified Intelligence Center 4
Unified Intelligence Center Reporting Enhancements 4
Post Call Treatment 4
Updated Features 4
Purge Enhancement 4
Deprecated Features 4
Important Notes 5
Unsupported and Supported Features 5
Third-Party Software Impacts 10

CHAPTER 3 Cisco Unfied Intelligence Center 11

New and Updated Features 11
New Features 11
Unified Intelligence Center Gadget Improvements 11
Support for New Russian Time Zone 11
Language Pack COP 11
Updated Features 12
Browser Support 12
Deprecated Features 12

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
iii
 Contents

Important Notes 12
VMware Tools Refresh 12
Encryption of Self-Signed Certificates 13
Load Balance 13
Recovery Disk 13
Unsupported and Removed Features 13
Third-Party Software Impacts 13

CHAPTER 4 Cisco Finesse 15

New and Updated Features 15
New Features 15
Sign In URL Now Requires FQDN 15
Multiple Call Variables Layouts 15
Finesse IP Phone Agent 16
Account Locked After Five Failed Sign In Attempts 16
Accessibility 17
Gadget Loading Indicator 17
Updated Features 17
Increased Phone Books and Contacts 17
Increased Team Wrap-Up Reasons 17
All ASCII Characters Now Supported When Making a Call 18
Dialog Notification API Populates requestId 18
Deprecated Features 18
Important Notes 18
Cisco Finesse Installation 18
Load Balancing for Finesse 18
Encryption of Self-signed Certificates 18
One Finesse Desktop or Finesse IPPA Session Per Agent 19
Wrap-Up and Transfer 19
Browser URL Button for Workflow Actions and Internet Explorer 11.0 19
Cisco Jabber for Windows 19
Hardware and Software Requirements 20
Related Documentation 21
Removed and Unsupported Features 21
Third-Party Software Impacts 21

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
iv
 Contents

CHAPTER 5 Cisco MediaSense 23

New and Updated Features 23
New Features 23
In-Browser Playback 23
Finesse AgentInfo Gadget 23
Agent Information in MediaSense Search and Play 24
Unified Communications Manager Line Display Name in MediaSense Search and
Play 24
Call Association for Network-Based Recording and Unified Border Element Dial Peer
Recording 24
Search on Archived Recordings 24
Updated Features 24
Deprecated Features 24
Important Notes 25
Removed and Unsupported Features 25
Third-Party Software Impacts 25

CHAPTER 6 Cisco SocialMiner 27

New and Updated Features 27
New Features 27
Discard an Email Message 27
Account Locked After Five Failed Sign In Attempts 27
Updated Features 28
Deprecated Features 28
Important Notes 28
SocialMiner OVA Template 28
Upgrade to SocialMiner 11.0(1) 28
Removed and Unsupported Features 28
Third-Party Software Impacts 29

CHAPTER 7 Cisco Unified Workforce Optimization Workforce Management 31

New and Updated Features 31
New Features 31
Updated Features 32

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
v
 Contents

Deprecated Features 32
Important Notes 32
Removed and Unsupported Features 32
Third-Party Software Impacts 33

CHAPTER 8 Cisco Unified Workforce Quality Management 35

New and Updated Features 35
New Features 35
Updated Features 36
Deprecated Features 37
Important Notes 37
Installation Notes 37
Multi-line Devices and Network Recording Service 38
Restarting the Network Recording Service and Poor Quality 38
"Stop running script" Message 38
"script missing" Message When Installing an SR 38
Long Fields Clear When Selecting Language 39
Contact ID Search 39
Last Call Attribution 39
Screen Recording Playback Memory Error 39
Supervisor or Manager Dashboard Access 39
Live Screen Monitoring Screen Flash 40
Team Scores All Data Report Displays Non-configured Users 40
Record Option Fails 40
Windows Aero Theme Not Supported 40
Live Screen Monitoring and Windows Remote Assistance 41
Related Documents 41
Removed and Unsupported Features 41
Third-party Software Impacts 41

CHAPTER 9 Caveats 43
Caveat Queries by Product 43
Bug Search Tool 43
Severity 3 or Higher Caveats for Release 11.0 44

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
vi
 CHAPTER 1
Introduction
• Release Notes for Contact Center Solutions, page 1

Release Notes for Contact Center Solutions

For Release 11.0, we are introducing release note compilations for each of the contact center solutions. The
compilations contain all of the release notes for one solution type and the components that you can use with
that contact center. Follow these links to find the release note compilations:
• Release Notes for Cisco Packaged Contact Center Enterprise Solution Release 11.0(1) at http://
www.cisco.com/c/en/us/support/customer-collaboration/packaged-contact-center-enterprise/
products-release-notes-list.html
• Release Notes for Cisco Unified Contact Center Enterprise Solution Release 11.0(1) at http://
www.cisco.com/c/en/us/support/customer-collaboration/unified-contact-center-enterprise/
products-release-notes-list.html
• Release Notes for Cisco Unified Contact Center Express Solution Release 11.0(1) at http://
www.cisco.com/c/en/us/support/customer-collaboration/unified-contact-center-express/
products-release-notes-list.html
• Release Notes for Cisco Hosted Collaboration Solution for Contact Center Release 11.0(1) at http://
www.cisco.com/c/en/us/support/unified-communications/hosted-collaboration-solution-contact-center/
products-release-notes-list.html.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
1
 Introduction
Release Notes for Contact Center Solutions

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
2
 CHAPTER 2
Cisco Unified Contact Center Express
• New and Updated Features, page 3
• Deprecated Features, page 4
• Important Notes, page 5
• Unsupported and Supported Features, page 5
• Third-Party Software Impacts, page 10

New and Updated Features

New Features

Email Enhancement
This feature allows the agent to discard email. Appropriate historical reports have been enhanced to provide
information regarding number of discarded emails.

Finesse IP Phone Agent

As CAD is deactivated in release 11.0(1), Finesse IP Phone Agent provides a replacement for CAD IP Phone
Agent (IPPA).

Outbound Enhancement
This feature allows outbound campaigns to have duplicate contact entries so that contacts can be called multiple
times within the same day.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
3
 Cisco Unified Contact Center Express
Updated Features

Standalone Unified Intelligence Center

This feature allows the Unified Intelligence Center to be installed on a standalone server that is connected to
Unified CCX to provide support for multiple data sources and custom reporting.

Unified Intelligence Center Reporting Enhancements

This feature introduces enhancements to Live Data Gadgets and Historical Reports to improve the user
experience.

Post Call Treatment

Post Call Treatment allows Unified Contact Center Express (UCCX) to provide treatment to an ICD call once
the agent ends the call from the Finesse Desktop.
Post Call Treatment can be used for use cases such as transferring the call to a survey for customer feedback.

Updated Features
The following sections describe updated features pertinent to Unified CCX Release 11.0(1).

Purge Enhancement
This feature enhances the existing feature of purging the database. The administrator can now set the purge
duration for a scheduled purge in Unified CCX Administration in addition to the purge start time. The
enhancement also allows the administrator to configure to initiate an automatic purge when the extent size
exceeds the set limits.

Deprecated Features
Cisco Agent Desktop
In Unified CCX 11.0(1), Cisco Agent Desktop and all its components such as Cisco Supervisor Desktop,
Cisco Agent Desktop reporting, on demand recording, remote monitoring, Cisco Agent Desktop Chat, Cisco
Agent Desktop Email features are blocked and customers are advised to use Finesse Agent Desktop and its
suite of products.
When you upgrade to Unified CCX 11.0(1) or when you do a fresh install of Unified CCX 11.0(1) version,
you will notice that:
• You will not be able to download CAD from Unified CCX.
• All CAD references in Unified CCX App admin have been removed.
• CAD IP Phone Agent has been migrated to work in Finesse and is available as part of standard, enhanced
and premium licenses.
• CAD specific email reports have been removed. However, the data is retained and can be accessed using
CAD email stock reports from the CDN (Cisco Developer Network).

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
4
 Cisco Unified Contact Center Express
Important Notes

• Recordings, configurations, and workflow cannot be migrated to Cisco Finesse.

Important Notes
Encryption of Self-Signed Certificates
Automatically generated self-signed certificates currently use SHA-1 encryption, which is deprecated.
Instead, use the platform administration tools to create self-signed certificates with SHA256 encryption. You
can access the tools by selecting OS Administration > Security > Certificate Management.

Note After the self-signed certificates are generated using the SHA256 encryption and the services are restarted,
the Unified Intelligence Center Live Data fails. Use SHA-1 encrypted certificates by regenerating them
from the CLI using the command: set cert regen tomcat.
Then restart the Cisco Tomcat and all the related services.

Connectivity Issues When VOS Firewall Disabled

The firewall on a VOS server uses port forwarding. If you disable the firewall, some applications can lose
connectivity because they use port forwarding. The Cisco Unified Intelligence Center OAMP page and any
other web application that connects to Cisco Tomcat on port 8443 fail when the firewall is down. The Cisco
Unified Real-Time Monitoring Tool (RTMT) client displays the following error:

RTMT application cannot communicate with specified node/cluster. Please

verify the host IP
address is correct and the network connection is up, and try again.

Unsupported and Supported Features

Unsupported Languages for Chat Transcript Download
The default language of the chat transcript PDF is English for customers whose languages (locales) are not
supported by SocialMiner. The chat transcript PDF supports all languages that SocialMiner supports except
for the following:
• Chinese Simplified (zh_CN)
• Chinese Traditional (zh_TW)
• Japanese (ja_JP)
• Korean (ko_KR)

If you type in any of the unsupported languages, the PDF will have a blank line in place of the line that is in
the unsupported language.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
5
 Cisco Unified Contact Center Express
Unsupported and Supported Features

Unsupported Options on Finesse for Direct Preview Outbound

Finesse does not support Skip, Skip-Next, Skip-Close, Reject, Cancel Reservation, and Do Not Call for direct
preview outbound calls.

Unsupported and Supported Features and Configurations for Progressive and Predictive Agent Outbound
Unsupported Features and Configurations for Progressive and Predictive Agent Outbound
• The “Get Reporting Statistic” step is not supported for progressive and predictive agent-based outbound
campaigns.
• Unified CCX does not support the translation or modification of the phone number that it uses to dial
outbound calls. If any “voice translation rules” that are configured in the gateway modify the phone
number, those rules are not supported.

Note You can use either of the following two supported methods to modify a dialed number
in the gateway:
• To remove the initial digits of the phone number, use forward-digits or digit-strip
in the dial-peer configuration.
• To add a prefix to the phone number, use prefix in the dial-peer configuration.

• For Outbound campaigns outside North America, additional configuration is required to add the
area-code-to-time-zone mapping. For more information, see the Cisco Unified Contact Center Express
Administration Guide, located at http://www.cisco.com/en/US/products/sw/custcosw/ps1846/products_
installation_and_configuration_guides_list.html.
• For multicountry Outbound campaigns, the area code must also include the country code.
• Unified CCX dialer will dial outbound contacts only if the publisher database is in the “IN SERVICE”
state.
• Finesse does not support the Do Not Call option.
• Outbound license usage is not captured in the License Utilization Cisco Unified Intelligence Center
report.
• You must enable Agent AutoAnswer manually for agent-based progressive and predictive calls when
you upgrade from an older Unified CCX release.

Supported Features and Configurations for Progressive and Predictive Agent Outbound
• CUBE is supported with the SIP Outbound Dialer and CPA . For more information , see the Compatibility
Matrix for Unified CCX, located at: http://docwiki.cisco.com/wiki/Compatibility_Matrix_for_Unified_
CCX.

Unsupported Configuration for IPv6

• Cisco Unified Communications Manager does not support SIP IPv6 signaling over UDP where the
maximum transmission unit (MTU) is greater than 1500. To ensure that you do not experience intermittent
call failure, change the transport protocol to TCP.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
6
Cisco Unified Contact Center Express
Unsupported and Supported Features

For more information, see the “Important Notes” section of the Release Notes for Cisco Unified
Communications Manager, located at:
http://www.cisco.com/c/en/us/support/unified-communications/
unified-communications-manager-callmanager/products-release-notes-list.html
Also, see “CSCuo71306” for details on this limitation.
• When using IPv6 and Outbound dialer, use a voice gateway IOS that contains the fix for “CSCul43754”.

Unsupported Configurations and Scenarios for Unified CCX

Unified CCX does not support the following configurations:
• Shared lines for CTI ports and CTI route points.
• Expansion servers, except for Automatic Speech Recognition (ASR), Text-To-Speech (TTS), SocialMiner,
and MediaSense, which must be separate, dedicated servers.
• ICD call answer or ICD call transfer using any third-party attendant console desk software.
• Within the same script, using the “Place Call” step to generate a call and then placing the call in a queue.
• SIP REFER between a switchboard and Unified CCX if the transfer is completed after the call is answered
on the Unified CCX CTI port because of media reestablishment issues.
• During TTS prompt playback, if the call is put on hold and then retrieved, the prompt does not continue
from the position at which it was left.
• Use of “Consult Transfer” or “Redirect” step from scripts to a translation pattern that maps back to a
route point.
• Use of “Consult Transfer”, “Redirect”, and “Place Call” steps to invoke or dial into "MeetMe" conferences.
• The following scenarios have issues:
• External -> Consult Transfer to RP ->Consult Transfer to RP -> Redirect to Unmonitored device
• External -> Redirect to RP -> Consult Transfer to RP -> Redirect to Unmonitored device
• External -> Consult Transfer to RP -> Redirect to RP -> Redirect to Unmonitored device
• External -> Consult Transfer to RP -> Redirect to Unmonitored device

Thus, use the Call Redirect Step in the script instead of Call Consult Transfer.

Unsupported Actions for Unified CCX Agents

Use of the following softkeys on a Cisco Unified IP Phone is not supported:
• Barge
• cBarge
• DND
• GPickup
• iDivert
• MeetMe

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
7
 Cisco Unified Contact Center Express
Unsupported and Supported Features

• Park
• Pickup

Unsupported and Supported Configurations for Agent Phones

Unsupported Configurations for Agent Phones
The following configurations are not supported for agent phones:
• Two lines on an agent phone that have the same extension but exist in different partitions.
• Unified CCX extension that is assigned to multiple devices.
• Configuring the same Unified CCX extension in more than one device profile, or configuring the same
Unified CCX extension in any combination of device profiles and devices. (Configuring a Unified CCX
extension in a single device profile is supported.)
• In the Unified Communications Manager Administration Directory Number Configuration web page
for each Unified CCX line, setting Maximum Number of Calls to a value other than 2.
• In the Unified Communications Manager Administration Directory Number Configuration web page
for each Unified CCX line, setting Busy Trigger to a value other than 1.
• Configuring a Cisco Unified IP Phone with Secure Real-Time Protocol (SRTP) for use in recording
with MediaSense.
• No Cisco Unified Communications Manager device can be forwarded to the Unified CCX extension of
an agent.
• The Unified CCX extension of an agent cannot be configured to forward to a Cisco Unified CCX route
point.
• Configuring the Unified Communications Manager Intercom feature.
• Configuring the Hold Reversion feature.
• Agent extensions cannot be added to hunt lists or hunt groups. If an agent has only one line, then the
agent phone cannot be part of a hunt list or hunt group. In the case of multiple lines, none of the lines
on the first four buttons on the phone must be part of the hunt group. For more details on multiple lines
support and number of monitored lines, see the Cisco Unified Contact Center Express Design Guide,
located at http://www.cisco.com/c/en/us/support/customer-collaboration/unified-contact-center-express/
products-implementation-design-guides-list.html.
• Video is not supported if you are using Cisco Jabber for Windows as agent phone.
• The Unified CCX extension of an agent cannot be configured with Call Forward All to a Cisco Unified
CCX Trigger or CTI route point.

Supported Configurations for Agent Phones

To determine the phone devices that are supported by Cisco Finesse and for use by Cisco Finesse IP Phone
agents, see the Compatibility Matrix for Unified CCX, located at:
http://docwiki.cisco.com/wiki/Compatibility_Matrix_for_Unified_CCX
The following configurations are supported on agent phones:
• A Unified CCX extension that is configured on a single device (but not on multiple devices).
• A Unified CCX extension that is configured in a single device profile (but not in multiple device profiles).

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
8
Cisco Unified Contact Center Express
Unsupported and Supported Features

• Multiple agents sharing the same Unified CCX extension, which you can set up as follows:
• Configure the Unified CCX extension to a single phone (not in a device profile).
• Associate the phone with all the agents who will use this extension.
• Select the appropriate directory number (DN) as the Unified CCX extension for each agent.

In this configuration, only one agent at a time can be logged in.

Note All agents who currently have the Unified CCX extension to be shared must log out before you configure
additional agents to share that extension.

Unsupported Features in Unified Communications Manager and Cisco Business Edition 6000
The following Unified Communications Manager features are not supported by Unified CCX. These features
are disabled by default and you should not enable them for Unified CCX. For more information about these
features, see Unified Communications Manager documentation, located at:
http://www.cisco.com/en/US/products/sw/voicesw/ps556/tsd_products_support_series_home.html
• Block External to External Transfer.
• DSCP IP CTIManager to Application service parameter.
You can enable this service parameter for Unified Communications Manager, but doing so does not
affect Unified CCX.
• Advanced Ad Hoc Conference Enabled service parameter.
• Drop ad hoc conference when the creator leaves the conference.
• Signaling (QSIG) Path Replacement (PR).
This feature must be disabled when Unified CCX is deployed. To disable this feature, set the Unified
Communications Manager service parameters Path Replacement Enabled and Path Replacement on
Tromboned Calls to False.
• Forced Authorization Code and Client Matter Code.
Because these features can be enabled per route pattern, you should turn them off for all route patterns
in the Unified Communications Manager cluster that Unified CCX might use. Enabling these features
for route patterns that Unified CCX does not use does not affect Unified CCX.
• Multilevel precedence and preemption (MLPP).
You can enable this feature for devices in the cluster that do not interact with Unified CCX.
• Do not use Unified Communications Manager Administration to add or change CTI ports or route points
that are used by Unified CCX or application users that are created by Unified CCX.

Unsupported Features in Custom Reports

The Do Not Call field is no longer available in Unified CCX 11.0(1) release onward. While upgrading to
Unified CCX 11.0, report will not be generated if the Do Not Call column is present in the custom report.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
9
 Cisco Unified Contact Center Express
Third-Party Software Impacts

You can generate the report by removing the Do Not Call column from the custom reports in Unified CCX
11.0(1).

Third-Party Software Impacts

For information on third-party software, see the Compatibility Matrix for Cisco Unified Contact Center Express
available at http://docwiki.cisco.com/wiki/Compatibility_Matrix_for_Unified_CCX.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
10
 CHAPTER 3
Cisco Unfied Intelligence Center
• New and Updated Features, page 11
• Third-Party Software Impacts, page 13

New and Updated Features

New Features
The following sections describe new features that are pertinent to Unified Intelligence Center Release 11.0(1).

Unified Intelligence Center Gadget Improvements

A toolbar is added to the reporting gadget. The toolbar includes options to select views, view thresholds only,
play and pause of live data updates, help, and maximize toolbar.
The gadget toolbar allows you to select multiple report views (up to five views), which is configured in the
Cisco Finesse administration page.

Support for New Russian Time Zone

Unified Intelligence Center supports the two new Russian time zone : Asia/Chita and Asia/Srednekolymsk.
The new time zones are included as part of Unified Intelligence Center.

Language Pack COP

From this release Unified Intelligence Center's default locale is English (U.S). You can enable all supported
locales in Unified Intelligence Center by installing the language pack on all nodes in a cluster. The language
pack is available as a Cisco Optional Package (COP), which can be downloaded from Cisco.comhttps://
software.cisco.com/download/type.html?mdfid=282163829&catid=null.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
11
 Cisco Unfied Intelligence Center
Updated Features

Note Canadian French is removed from the language COP for this release.

Note Customers installing or upgrading to Unified Intelligence Center 11.0(1) must apply the language COP
on all nodes in a cluster.

Updated Features
There are no updated features for Cisco Unified Intelligence Center Release 11.0(1).

Browser Support
In this release Unified Intelligence Center supported browser versions are as follows:

Internet Internet Internet Explorer Internet Explorer Firefox 38

Explorer 10 Explorer 11 10 Compatibility 11 Compatibility Extended
Native Mode Native Mode Mode Mode Supported
Releases
(ESRs) and
higher ESRs
Cisco Unified No No Yes Yes Yes
Intelligence Center

Cisco Unified Yes Yes Yes Yes Yes

Intelligence Center
(Live Data Gadgets)

Deprecated Features
There are no deprecated features for Cisco Unified Intelligence Center Release 11.0(1).

Important Notes

VMware Tools Refresh

The VMware tools command utils vmtools upgrade is replaced with utils vmtools refresh.
To know more about the command syntax, see Command Line Interface in the Administration Console User
Guide for Cisco Unified Intelligence Center.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
12
 Cisco Unfied Intelligence Center
Unsupported and Removed Features

Encryption of Self-Signed Certificates

Automatically generated self-signed certificates currently use SHA-1 encryption, which is deprecated.
Instead, use the platform administration tools to create self-signed certificates with SHA256 encryption. You
can access the tools by selecting OS Administration > Security > Certificate Management.

Load Balance
A Unified Intelligence Center deployment with an optional Cisco Application Control Engine (ACE) load
balancer is not supported. System administrators now have the server load balancing option when Unified
Intelligence Center experiences heavy reporting load. For more information see, the Administration Console
User Guide for Cisco Unified Intelligence Center.

Recovery Disk
The server recovery instructions are explained in the Installation and Upgrade Guide for Cisco Unified
Intelligence Center under the chapter Frequently Asked Questions. The instructions provide are not updated
and a document defect is opened https://tools.cisco.com/bugsearch/bug/CSCuv67000 to address this.

Unsupported and Removed Features

There are no unsupported or removed features for Cisco Unified Intelligence Center Release 11.0(1).

Third-Party Software Impacts

There are no third-party software impacts on Cisco Unified Intelligence Center Release 11.0(1).

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
13
 Cisco Unfied Intelligence Center
Third-Party Software Impacts

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
14
 CHAPTER 4
Cisco Finesse
• New and Updated Features, page 15
• Deprecated Features, page 18
• Important Notes, page 18
• Removed and Unsupported Features, page 21
• Third-Party Software Impacts, page 21

New and Updated Features

New Features

Sign In URL Now Requires FQDN

To sign in to the Finesse administration console or the Finesse agent desktop, enter the fully qualified domain
name (FQDN) of the Finesse server in the URL. If you enter the server IP address or hostname, Finesse
redirects your browser to the server FQDN.

Multiple Call Variables Layouts

In previous releases, Finesse only supported one default Call Variables Layout. With Release 11.0(1), the
Call Variables Layout gadget allows you to define up to 200 unique Call Variables Layouts (one default layout
and 199 custom layouts) to display on the Finesse agent desktop. As part of this functionality:
• You can use a workflow to specify the Call Variables Layout that an agent sees when they receive a
call.
• For a new Release 11.0(1) installation, Finesse provides a default layout.
• For upgrades from an earlier release, Finesse migrates the previously configured default layout and
assigns it the default name and description.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
15
 Cisco Finesse
New Features

Finesse IP Phone Agent

With Finesse IP Phone Agent (IPPA), agents can access Finesse capabilities on their Cisco IP Phone as an
alternative to accessing Finesse through the browser. Finesse IPPA does not provide the full set of Finesse
features that are supported using the browser, but it does allow agents and supervisors to receive and manage
Finesse calls if they lose or do not have access to a PC.

Note Supervisors can sign in to Finesse on their IP Phones and perform all agent tasks, but supervisor tasks
such as monitor, barge, and intercept are not supported. To perform supervisor tasks, supervisors must
sign in to the Finesse desktop.

In Release 11.0(1), Finesse IPPA supports the following functionality:

• Sign in/sign out
• Pending state
• Wrap-up reasons
• Optional wrap-up
• Not Ready reasons
• State change using reason codes
• One Button Sign In

Account Locked After Five Failed Sign In Attempts

If an administrator tries to sign in to the Finesse administrator console (or diagnostic portal) with the wrong
password five times in a row, Finesse blocks access to that user account for a period up to 30 minutes. For
security reasons, Finesse does not alert the user that their account is locked. They must wait 30 minutes and
try again.
Similarly, if agents or supervisors sign in to the desktop five times in a row with the wrong password, Finesse
blocks access to that user account. However, in this case, the lockout period is only 5 minutes. This restriction
also applies when agents and supervisors sign in using Finesse IP Phone Agent (IPPA).

Note When an agent or supervisor account is locked, subsequent attempts to sign in, even with correct credentials,
reset the lockout period to 5 minutes again. For example, if a locked user tries to sign in again after only
4 minutes, the lockout period is reset and the user must wait another 5 minutes. This reset does not apply
to the administrator account.

To view whether a user account is locked, enter the following CLI command:
file get activelog desktop recurs compress
Then extract the zipped output, and search the catalina.out logs (opt/cisco/desktop/finesse/logs/catalina.out)
for the following message referring to the locked username:
An attempt was made to authenticate the locked user "<username>"

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
16
 Cisco Finesse
Updated Features

Accessibility
The Finesse desktop supports features that improve accessibility for low-vision and vision-impaired users.

Note Finesse supports these features only with Internet Explorer 11.0 and only on the agent desktop, not the
supervisor desktop or administration console.

Gadget Loading Indicator

Finesse now provides a gadget loading indicator that displays a loading message while a gadget is initially
loading in Finesse. If you are a developer creating a gadget, include this functionality in your gadget to provide
a consistent user experience within Finesse.

Updated Features

Increased Phone Books and Contacts

Finesse Release 11.0(1) increases the maximum number of team phone books from 50 to 300 and total contacts
in all phone books from 1500 to 50,000. See the following table for details.

Table 1: Maximum Numbers of Phone Books and Contacts

Item Maximum Notes

Total contacts in all phone books 50,000 Increased from 1500.

Team phone books 300 Increased from 50.

Global phone books 10 Unchanged.

Displayed contacts per agent 1500 Unchanged. These contacts are retrieved first from the
global phone books and then from the team phone books.

Contacts per phone book 1500 Unchanged.

Increased Team Wrap-Up Reasons

Finesse Release 11.0(1) increases the maximum number of team wrap-up reasons from 100 to 1500. However,
you can still assign no more than 100 team wrap-up reasons to an individual team. The maximum number of
global wrap-up reasons remains unchanged at 100.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
17
 Cisco Finesse
Deprecated Features

All ASCII Characters Now Supported When Making a Call

Finesse now supports the use of any ASCII character when you make a call. Finesse no longer converts letters
typed into the dial pad into numbers, nor does it remove non-numeric characters (including parentheses and
hyphens) from phone numbers.

Dialog Notification API Populates requestId

In the Dialog Notification API, the requestId tag is now populated when a user makes a request. (For an
incoming call, the requestId tag is empty.)

Deprecated Features
This release has no deprecated features.

Important Notes

Cisco Finesse Installation

In a Unified CCX deployment, Finesse is installed coresident with Unified CCX, as part of the Unified CCX
installer. For more information about installing Finesse with Unified CCX, see the Cisco Unified Contact
Center Express Installation Guide at http://www.cisco.com/en/US/partner/products/sw/custcosw/ps1846/
prod_installation_guides_list.html.

Load Balancing for Finesse

With Finesse, the use of a load balancer after sign-in is neither required nor supported. For information about
Finesse support of a load balancer before sign-in or with the Finesse APIs, see the Cisco Unified Contact
Center Express Design Guide at http://www.cisco.com/c/en/us/support/customer-collaboration/
unified-contact-center-express/products-implementation-design-guides-list.html .

Encryption of Self-signed Certificates

Encryption of Self-Signed Certificates
Automatically generated self-signed certificates currently use SHA-1 encryption, which is deprecated.
Instead, use the platform administration tools to create self-signed certificates with SHA256 encryption. You
can access the tools by selecting OS Administration > Security > Certificate Management.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
18
 Cisco Finesse
One Finesse Desktop or Finesse IPPA Session Per Agent

Note After the self-signed certificates are generated using the SHA256 encryption and the services are restarted,
the Unified Intelligence Center Live Data fails. Use SHA-1 encrypted certificates by regenerating them
from the CLI using the command: set cert regen tomcat.
Then restart the Cisco Tomcat and all the related services.

One Finesse Desktop or Finesse IPPA Session Per Agent

Finesse has the following agent session limitations:
• Finesse can support a mix of agents in which some agents use Finesse IPPA and other agents use the
Finesse desktop (license permitting).
• Agents cannot sign in to both the Finesse desktop and Finesse IPPA at the same time.
• Agents can sign in to only one instance of either the Finesse desktop or Finesse IP Phone Agent (IPPA)
at one time.
• When agents are signed in to the Finesse desktop or Finesse IPPA, they can also sign in to a third-party
application using the Finesse API at the same time. (This setup is considered a custom development.
Like other Finesse customizations, the customer or partner is responsible for proper development and
testing of this custom setup.)

Wrap-Up and Transfer

An agent cannot enter wrap-up data following a completed transfer because the call is not only cleared, but
also completely ended. If an agent wants to enter wrap-up data for a transferred call, that agent must select a
wrap-up reason while the call is in progress.

Note If an agent is configured for wrap-up, that agent may still enter Wrap-Up state after transferring the call.
However, the wrap-up timer does not appear on the Finesse desktop after the call is transferred.

Browser URL Button for Workflow Actions and Internet Explorer 11.0
The context menu for the Browser URL button on the Manage Workflow Actions gadget is disabled in Internet
Explorer 11.0. An administrator must use keyboard shortcuts for Select All, Cut, Copy, and Paste for this
particular field.

Cisco Jabber for Windows

Finesse supports Cisco Jabber for Windows as a contact center voice endpoint. Finesse supports the following
Jabber functionality:
• Voice only (Video is not supported)

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
19
 Cisco Finesse
Hardware and Software Requirements

• Built-In Bridge (for silent monitoring)

• IM and Presence

Note Agents cannot use Jabber to transfer or conference calls. Agents must use the Finesse desktop for transfer
and conference.

You must change the default configuration for Jabber as follows:

• Change Maximum number of calls from 6 to 2.
• Change Busy trigger from 2 to 1.

Hardware and Software Requirements

For Finesse compatibility requirements, including supported phones and browsers, see the Compatibility
Matrix for Unified CCX.

Finesse Client Requirements

The minimum supported screen resolution for Finesse clients is 1024 x 768.

Important Requirements, such as processor speed and RAM, for clients that access the Finesse desktop can vary.
Desktops that receive events for more than one agent (such as a supervisor desktop running Team
Performance and Queue Statistics gadgets or an agent desktop running Live Data reports that contain
information about other agents or skill groups) require more processing power than desktops that receive
events for a single agent.
Factors that determine how much power is required for the client include, but are not limited to, the
following:
• Contact center traffic
• Additional integrated gadgets in the desktop (such as Live Data reports or third-party gadgets)
• Other applications that run on the client and share resources with the Finesse desktop

Hardware
Click here for information about the system hardware requirements for Unified Communications servers. For
virtualization information for Cisco Finesse, go to http://docwiki.cisco.com/wiki/Virtualization_for_Cisco_
Finesse.

Load and Capacity

Finesse is qualified to support up to 360 desktop or Finesse IPPA agents and 40 supervisors (for a total of
400 users). Finesse IPPA agents can also access the Finesse desktop (but not both at the same time) without
affecting the total number of supported users, license permitting. Unified CCX supports HTTPS only.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
20
 Cisco Finesse
Related Documentation

Related Documentation
For information about Finesse deployments with Unified Contact Center Express (Unified CCX), see the
Unified CCX documentation on Cisco.com:
http://www.cisco.com/en/US/partner/products/sw/custcosw/ps1846/tsd_products_support_series_home.html
Developer information is available from the Finesse page on the Cisco Developer Network (requires sign in
with Cisco.com user ID and password):
https://developer.cisco.com/site/finesse/
Cisco DevNet provides API documentation (Cisco Finesse Web Services Developer Guide), a blog, and
forums.
Troubleshooting tips for Cisco Finesse are available on DocWiki at:
http://docwiki.cisco.com/wiki/Troubleshooting_Cisco_Finesse

Removed and Unsupported Features

This release has no removed or unsupported features.

Third-Party Software Impacts

This release has no third-party software impacts.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
21
 Cisco Finesse
Third-Party Software Impacts

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
22
 CHAPTER 5
Cisco MediaSense
• New and Updated Features, page 23
• Third-Party Software Impacts, page 25

New and Updated Features

New Features

In-Browser Playback
In addition to Java media player, you can play back an audio recording using the HTML5 playback feature
of the browser. While using in-browser playback, you do not need to download the recording. To enable
in-browser player, configure the settings in the Search and Play Configuration window of Cisco MediaSense
Administration. In MediaSense Search and Play, an in-browser player appears at the bottom of the recording
selected for playback and displays its progress.
For more information, see the "In-Browser Playback" section of the Cisco MediaSense User Guide at http://
www.cisco.com/c/en/us/support/customer-collaboration/mediasense/products-user-guide-list.html .

Finesse AgentInfo Gadget

Finesse AgentInfo gadget is present on the Finesse Agent desktop to convey agent information from Finesse
to MediaSense. When an agent signs in to the desktop, the gadget automatically signs in to MediaSense server
and provides agent information. The agent information includes login ID, login extension, first name, and last
name. It also keeps a track of the agent signs in and out time.
For more information, see the "Finesse AgentInfo Gadget" section in the Cisco MediaSense User Guide at
http://www.cisco.com/c/en/us/support/customer-collaboration/mediasense/products-user-guide-list.html .

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
23
 Cisco MediaSense
Updated Features

Agent Information in MediaSense Search and Play

In MediaSense Search and Play, you can search for recordings based on agent information and view agent
information in the search results. The agent information includes login ID, login name, first name, and last
name. To customize the display of agent information parameters in Search and Play, select or deselect the
parameters in the Search and Play Configuration window of Cisco MediaSense Administration.
For more information, see the "Search for, Play, or Download a Recorded Call" and "Search and Play
Configuration" sections of the Cisco MediaSense User Guide at http://www.cisco.com/c/en/us/support/
customer-collaboration/mediasense/products-user-guide-list.html .

Unified Communications Manager Line Display Name in MediaSense Search and Play
In MediaSense Search and Play, enter Unified Communications Manager Line Display name in the Line
Name text box to search for a recording. You can also view the Unified Communications Manager Line
Display Name as Line Name if it is configured in Unified Communications Manager.
To enable Line Name as search option and view it in the search results, check the Show Line Display Name
check box in Search and Play Configuration window in MediaSense Administration. For more information,
see "Search and Play Configuration" section of the Cisco MediaSense User Guide at http://www.cisco.com/
c/en/us/support/customer-collaboration/mediasense/products-user-guide-list.html .

Call Association for Network-Based Recording and Unified Border Element Dial Peer Recording
MediaSense groups strongly associated calls which have at least one common xRefCi value in case of sessions
recorded through Unified Communications Manager, and at least one common CCID value in case of sessions
recorded through Unified Border Element. MediaSense 11.0(1) supports call association for Unified
Communications Manager network-based recordings and Unified Border Element dial peer recordings.

Search on Archived Recordings

You can search archived recordings in MediaSense Search and Play using the Archive Calls tab. Use the
Session ID, participant ID, and date range to search the archived recordings. To enable archived recordings
search, check the Enable Search on Archived Recordings check box in the MediaSense Archive
Configuration window of Cisco MediaSense Administration.
For more information, see the "Archival" section of the Cisco MediaSense User Guide at http://www.cisco.com/
c/en/us/support/customer-collaboration/mediasense/products-user-guide-list.html .

Updated Features
There are no updated features for MediaSense 11.0(1).

Deprecated Features
Cisco Finesse
MediaSense 11.0(1) supports Finesse 11.0; earlier versions are not supported any longer.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
24
 Cisco MediaSense
Important Notes

Cisco Unified Communications Manager AXL Authentication 8.x

MediaSense 11.0(1) no longer supports Cisco Unified Communications Manager AXL Authentication 8.x.

Important Notes
There are no important notes for MediaSense 11.0(1).

Removed and Unsupported Features

There are no removed and unsupported features for MediaSense 11.0(1).

Third-Party Software Impacts

For information on third-party software, see the Compatibility Matrix for Cisco MediaSense available at http:/
/docwiki.cisco.com/wiki/Cisco_MediaSense_Compatibility_Matrix.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
25
 Cisco MediaSense
Third-Party Software Impacts

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
26
 CHAPTER 6
Cisco SocialMiner
• New and Updated Features, page 27
• Deprecated Features, page 28
• Important Notes, page 28
• Removed and Unsupported Features, page 28
• Third-Party Software Impacts, page 29

New and Updated Features

New Features
The following sections describe new features for Cisco SocialMiner Release 11.0(1).

Discard an Email Message

SocialMiner Release 11.0(1) provides this feature for Unified Contact Center Express (Unified CCX).
This feature allows email support agents to discard spam and trivial email messages that do not qualify a
response.
This feature requires SocialMiner integration with Unified CCX and is delivered through Cisco Finesse. For
more information about discarding email message, see the section Discard an Email Message in Cisco Finesse
Agent and Supervisor Desktop User Guide for Cisco Unified Contact Center Express, Release 11.0(1) at http:/
/www.cisco.com/c/en/us/support/customer-collaboration/unified-contact-center-express/
products-user-guide-list.html.

Account Locked After Five Failed Sign In Attempts

If an administrator tries to sign in to the SocialMiner administration console with the wrong credentials five
times in a row, SocialMiner blocks access to that user account for a period up to 30 minutes.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
27
 Cisco SocialMiner
Updated Features

For security reasons, SocialMiner does not alert the user that the account is locked. The administrator must
wait for 30 minutes and try again.
This feature also applies to all authenticated REST APIs of SocialMiner.

Updated Features
There are no updated features for SocialMiner 11.0(1).

Deprecated Features
This release has no deprecated features.

Important Notes

SocialMiner OVA Template

Use the OVA template Cisco_SocialMiner_v11.0_VMv8.ova for the fresh installation of SocialMiner Release
11.0(1).
You can obtain the Virtual Server Template (OVA) file needed to create a Virtual Machine from https://
software.cisco.com/download/type.html?mdfid=283613136&flowid=73189 .
The Cisco SocialMiner 11.0(1) Virtual Server Template (OVA) defines a virtual machine configuration that
is supported in the SocialMiner 11.0(1) release. This OVA contains all supported virtual machine configurations
of this release.

Upgrade to SocialMiner 11.0(1)

For upgrades from SocialMiner 10.x to SocialMiner 11.x, apply the corresponding COP file from the Command
Line Interface (CLI) and modify the SocialMiner Virtual Machine's operating system version, total video
memory, and network adapter type parameters before beginning the upgrade process.

Note If you are on version 10.x, perform upgrade directly to 11.0(1).

If you are on a version lower than 10.0(1), upgrade to 10.x and then upgrade to 11.0(1).

For information about SocialMiner Upgrade, see the section Upgrade SocialMiner in SocialMiner Installation
and Upgrade Guide, Release 11.0(1) at http://www.cisco.com/c/en/us/support/customer-collaboration/
socialminer/tsd-products-support-series-home.html.

Removed and Unsupported Features

From this release, Cisco Security Agent (CSA) is removed.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
28
 Cisco SocialMiner
Third-Party Software Impacts

Third-Party Software Impacts

This release has no third-party software impacts.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
29
 Cisco SocialMiner
Third-Party Software Impacts

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
30
 CHAPTER 7
Cisco Unified Workforce Optimization Workforce
Management
• New and Updated Features, page 31
• Deprecated Features, page 32
• Important Notes, page 32
• Removed and Unsupported Features, page 32
• Third-Party Software Impacts, page 33

New and Updated Features

New Features
• Support for Cisco Unified Contact Center Express 11.0
• Support for Microsoft SQL Server 2014
• Support for dynamic scheduling
• Support for multiskill scheduling
• Support for mentoring requests
• Support for scheduling incentives
• Interface localized in Danish, Dutch, English, French, German, Italian, Portuguese (Brazilian), Spanish
(European) and Swedish
• Help localized in Danish, Dutch, English, French, German, Spanish (European), and Portuguese (Brazilian)
• Support for high availability for the Workforce Optimization interface
• Support for non-ACD agents in synced systems.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
31
 Cisco Unified Workforce Optimization Workforce Management
Updated Features

Updated Features
This section details the updated features in this release:
• Advanced bundle features of Vacation Planning and Strategic Planning now available to all WFM
customers.
• Support for high availability for the WFO interface.
• Support for non-ACD agents in synced systems.
• Addition of the Balanced Schedule option when running a schedule.
• Block scheduling (MSAQ) is now always on.
• Improvements in how service level percentage rollups are calculated.

Deprecated Features
This release has no deprecated features.

Important Notes
This section details the installation related notes. For step-by-step installation and upgrade instructions, see
the Cisco Workforce Management Installation Guide.

Recalculating Actual Service Level after Upgrade

The actual service level for the period before WFM 10.5(1) SR3 or newer was installed will not be correct
unless the data for that period is recaptured. Data acquired after the date of the upgrade will display the correct
actual service date.
See “Historical Data” in the Workforce Management User Guide and “Historical Data Capture” in the Workforce
Management Data Import Reference Guide for more information on how to capture your historical data.

Removed and Unsupported Features

This release has no removed and unsupported features. This section lists the limitations and restrictions in
this release.

Limitations and Restrictions

The following sections identify limitations of the product, and any workarounds that exist to deal with issues.
PC validation incorrectly indicates that Google Chrome is an invalid browser
The Validate my PC configuration feature will return a result of Bad for the browser type and version if a
WFM user’s desktop uses the Google Chrome browser, even though Chrome is a supported browser. The user
can ignore this incorrect result and log into WFM normally.
Schedule exceptions are not assigned to agents after schedule interval trade

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
32
 Cisco Unified Workforce Optimization Workforce Management
Third-Party Software Impacts

If an exception is added to an agent’s schedule after that schedule is run (Schedule > Edit Schedule), and
then that exception interval in that agent’s schedule is copied to other agents’ schedules to give them the same
exception (Intraday > Schedule Trade), the exception will appear in all agents’ schedules. However, it will
appear only in the original agent’s list of exceptions (Agents > Agent Detail > Exceptions tab).
To work around this issue, select the “This service queue allows block scheduling” check box on the Service
Queue page and run the schedule again.

Third-Party Software Impacts

This release has no third-party software impacts.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
33
 Cisco Unified Workforce Optimization Workforce Management
Third-Party Software Impacts

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
34
 CHAPTER 8
Cisco Unified Workforce Quality Management
• New and Updated Features, page 35
• Deprecated Features, page 37
• Important Notes, page 37
• Removed and Unsupported Features, page 41
• Third-party Software Impacts, page 41

New and Updated Features

New Features
The following is a summary of the new features added to the 11.0 release.
• Merged the Desktop Requirements Guide, Desktop Applications Deployment Guide, and Firewall
Configuration Guide into the Installation Guide.
• Added support for Network Based Recording using the Cisco Unified CM Recording functionality from
either an IP phone (BIB) or gateway. Network Based Recording supports Cisco CUBE Recording via
SIP and Cisco MediaSense.
• Added information on hard disk drive (HDD) partitioning.
• Added information on configuring a customer relationship management (CRM) system.
• Added information on integrating SNMP.
• Added the Kerberos Authentication check box to the Enterprise Settings window. When enabled, a user
must enter the AD credentials to access Recording controls.
• Added support for cloud based recording storage for Quality Management.
• Added support for two stage upload.
• Added support for Unified CCX version 11.0, Unified CM 11.0(1a), and MediaSense11.0.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
35
 Cisco Unified Workforce Quality Management
Updated Features

• Added support for configuring the default time format at a global level. You can now choose between
the 24 hour and the 12 hour time format in Interface Settings under Recordings > Interface Configuration.
• Added support for importing and exporting an inclusion/exclusion list to the Inclusion List under System
Configuration.
• Added support for the Contact Basic Search API. The Contact Basic Search API returns details about
an in progress or most recently completed call. See the API Programmer Guide for more information.
• Added localized PDFs for the User Guide in Chinese (Simplified and Traditional), Danish, Dutch,
French, German, Korean, Portuguese (Brazil), and Spanish (European).

Updated Features
The following is a summary of the new features added to the 11.0 release.
• Desktop Configuration Administration has been renamed Recording Columns and now appears under
Recordings > Interface Configuration.
• Export Recordings Administration has been renamed to Export Permissions and now appears under
Recordings > Interface Configuration > Interface Settings.
• The roles and scope for the system reports in the Reporting application have changed as follows:
System Report Old Roles New Roles
Recording Access By User Manager System Administrator
Archive User Telephony Administrator
Archive User
Manager

Recording Access By Contact Manager System Administrator

Archive User Telephony Administrator
Archive User
Manager

User Recording Status Supervisor System Administrator

Telephony Administrator
Archive User
Manager

System Status Manager System Administrator

Telephony Administrator

Audit Trail Not applicable System Administrator

• Improved the scrubber on the Media Player.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
36
 Cisco Unified Workforce Quality Management
Deprecated Features

• Updated the instructions for installing desktop applications. See “Installing Desktop Applications” in
the Installation Guide.
• Updated the localized strings to the Cisco Workforce Optimization interface in Danish, Dutch, German,
French, Italian, Portuguese (Brazil), Spanish (European), and Swedish
• Updated the localized help for Quality Management version 10.5(1) in Danish, Dutch, French German,
Portuguese (Brazil), and Spanish (European).
• Included the localized help for Quality Management version 10.0 in Italian and Swedish. For the latest
description of Quality Management 11.0 features see the English version of the Application Guide.

Deprecated Features
This release has no deprecated features.

Important Notes

Installation Notes

Note Over the top upgrades from version 10.5 and earlier to 11.0 are not supported. All such upgrades must be
manual. This means that the old version of Recording and Quality Management (but not your Recording
and Quality Management database) must be uninstalled before the new version is installed. Over the top
upgrades from 11.0 to newer versions of 11.0 are supported.

If you are upgrading from 10.5(1) SR4, note that the installation instructions has changed for web server
redundancy. A Configure High Availability tool has been added to System Configuration (PostInstall.exe).
See “Web Server Redundancy” in the Installation Guide for more information.
If you upgrading from 10.5(1) or earlier and you modified the recordingcontrols.properties file (for example,
to limit the buttons that users can see) for Recording Controls, you must update the recordingcontrols.properties
file after you install 11.0. The recordingcontrols.properties file has been updated to support new features.
Possible errors that might occur when you install 11.0(1) are as follows:
• If you upgraded from an 8.x system to 10.5 before 11.0, you will need to adjust the database entries after
installing 10.5(1). To adjust the data base entries run the following command against the SQMDB in
SQL:
update ServerPropertiesset
setting=100
where id=’serverMaxConcurrentRecordings’ and set=100

• If you notice that the associated call IDs are blank on some calls and that causes recording playback to
fail, run the following SQL script in Microsoft SQL Server Management Studio:
UPDATE ccr SET associatedCallId=POWER(CAST(2 AS BIGINT),48) |
POWER(CAST(2 AS BIGINT),32) *
FLOOR(DATEDIFF(DAY,'1970-01-01',startTime) / 7) | icmCallId FROM ccr
WHERE associatedCallId=''

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
37
 Cisco Unified Workforce Quality Management
Multi-line Devices and Network Recording Service

• If a “script missing” message appears when you install the SR, the Patches.xml file is corrupt. To work
around this problem, delete the Patches.xml file in the webapps/TUP/<product> folder, and then run a
repair on the base release from Add or Remove Programs. The repair on the SR will be initiated
automatically.

For step-by-step installation and upgrade instructions, see the Installation Guide.

Multi-line Devices and Network Recording Service

• Multi-line devices must use the same Network Recording service for each extension

When configuring extensions on a single device for network recording, any extensions that are enabled for
network recording must use the same Network Recording service. Quality Management Administrator
associates a device with a recording service, so it cannot assign an individual extension with a separate
recording service.

Restarting the Network Recording Service and Poor Quality

• Restarting the Network Recording service while performing network recording might cause poor quality
audio

Calls that are active when the Network Recording service is stopped and are still active when the service is
restarted might result in recordings that have poor-sounding audio.
To work around this problem, do not restart the Network Recording service while calls are active. Symptoms
will persist until all the calls that were active when the Network Recording service was stopped have been
disconnected.

"Stop running script" Message

The “stop running script” message appears when there are more than five widgets in your dashboard when
using Microsoft Internet Explorer 8 or 9. If you use more than five widgets, the page becomes slow and
unresponsive.
To work around this problem, upgrade to Microsoft Internet Explorer 10 or 11.

"script missing" Message When Installing an SR

The “script missing” message might appear when you install Quality Management. The message appears when
the install attempts to modify a corrupted Patches.xml file.
To work around this problem, delete the Patches.xml file in the webapps/TUP/<product> folder, and then run
a repair on the base release from Add or Remove Programs. The repair on the SR will be initiated automatically.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
38
 Cisco Unified Workforce Quality Management
Long Fields Clear When Selecting Language

Long Fields Clear When Selecting Language

When you complete the fields on the Workforce Optimization Login page and then choose a language from
the Language drop-down list, the login fields are cleared. To work around this issue, choose a language before
you complete the remaining login fields.

Contact ID Search
• A search by Contact ID should ignore all other filters

Search Recordings only ignores the values for Specific Date and Date Range when you specify a Contact ID.
If you include values for other search fields, the Contact ID you are looking for might not appear in the search
results.
To work around this problem, use the Contact ID field alone or only with the Date Range and Specific Date
fields that will be ignored. If you use one of the other filters the specified values need to match the data in the
record for the search to be successful.

Last Call Attribution

• A call is attributed to the last user who logged into a phone configured for Hot Desking and MediaSense
Recording

In this scenario, a Hot Desking agent receives a call. While the first Hot Desking agent is on the call, a second
Hot Desking agent logs in to the same phone using an API tool. When the call ends, the Record server assigns
the call to the second Hot Desking agent. There is no workaround for this issue.

Screen Recording Playback Memory Error

The generic memory error icon appears when you try to play back a recording that includes a screen recording.
When the generic memory error icon appears in the Screen window and the screen recording will not play
back.
Adobe Flash Player displays the generic memory error icon when running in a very low memory environment.
It indicates that the web browser does not have much memory available. For more information on the generic
memory icon, go to: http://blogs.adobe.com/dekesmith/2012/06/07/
what-is-the-gray-circle-with-an-exclamation-mark-or-ba
To work around this issue, close the web browser, then reopen the web browser and try again.

Supervisor or Manager Dashboard Access

• When a supervisor or manager accesses the Dashboard an error message appears

When you first access the Dashboard, the following error message appears:The <range> is not valid

Note that the value for each band changed from a range of numbers to a single integer in 11.0.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
39
 Cisco Unified Workforce Quality Management
Live Screen Monitoring Screen Flash

To resolve this issue, delete the existing Best Performers Widget and then create a new one. Or change the
Band values in the widget from a range of numbers to a single integer.

Live Screen Monitoring Screen Flash

• The client PC flashes when Live Screen Monitoring is initiated

When you initiate Live Screen Monitoring, the client PC will flash black for a few seconds before establishing
the connection.
To disable the flash:
1 Click Start, type services.msc in the search field, and then press Enter.
2 From the Services window, double-click Desktop Window Manager Session Manager.
3 Choose Disabled from the Startup type drop-down list and then click Apply. You will need to restart your
client PC.
4 Optional: Disable the Desktop Windows Manager Session Manager if you do not want to restart your
client PC.

Team Scores All Data Report Displays Non-configured Users

• The Team Scores All Data report displays non-configured users

When generating a report, the Agent field displays two instances of the same user. In the database, these are
actually different users with the same name, only one user is configured and should be shown. There is no
workaround for this issue.

Record Option Fails

• Record option in Recording Controls fails to tag and record the call

When issuing a Record option in Recording Controls, the API fails to record the call and mark the call as
“agent tagged”. There is no workaround for this issue.

Windows Aero Theme Not Supported

Live screen monitoring is based off the Microsoft Windows Desktop Sharing API. This same API is used by
Microsoft Windows Remote Assistance. One limitation of the Microsoft Windows Desktop Sharing API is
that it does not support the Windows Aero theme for the PC being monitored during the time when another
PC is connected to and viewing that PC. Every time a user begins to live screen monitor your PC, Windows
must automatically switch your PC to the Windows Basic theme. Once the live screen monitor session on
your PC ends, Windows will automatically switch your PC back to the Windows Aero theme. Based on
customer feedback, we changed the behavior in 10.5(1) SR5 so it would only switch to the Windows Basic
theme once at the start of the Desktop Recording service. The Windows Basic theme will remain until the
Desktop Recording service is stopped.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
40
 Cisco Unified Workforce Quality Management
Live Screen Monitoring and Windows Remote Assistance

If this is not the desired behavior, choose one of the following work arounds:
• Configure your PC to always use the Windows Basic theme. Then when the QM Desktop Recording
service starts it does not have to change to that theme since it is already in place.
• Disable the live screen monitoring feature in Monitoring and Recording Administrator by clearing the
Enabled check box under Live Screen Monitor in the Interface Settings window under Recordings. This
will disable live screen monitoring for all users. When live screen monitoring is disabled, it will not
switch to the Windows Basic theme.

Live Screen Monitoring and Windows Remote Assistance

• Unable to connect to the PC using Windows Remote Assistance if Live Screen Monitoring is enabled

Cisco uses Windows Remote Assistance to provide the live screen monitoring session. You are only allowed
to have a single incoming session per PC, so while the Live Monitoring service is in use, any attempts to
connect to the PC will be denied. To workaround this issue, disable Live Monitoring or change it to only start
the service when a Live Monitoring session is requested. If you are using the Windows Aero theme, every
time a Live Monitoring session is requested, the agent's screen will change from Aero to Basic causing a
screen flash.

Related Documents
• Cisco Unified Workforce Optimization Recording and Quality Management User Guide
• Cisco Unified Workforce Optimization Recording and Quality Management Quick Start Guide
• Cisco Unified Workforce Optimization Recording and Quality Management Administrator Guide
• Cisco Unified Workforce Optimization Recording and Quality Management Installation Guide
• Cisco Unified Workforce Optimization Recording and Quality Management API Programmer Guide
• Cisco Unified Workforce Optimization Recording and Quality Management Design Guide
• Cisco Unified Workforce Optimization Recording and Quality Management Integration Guide for CAD
and Finesse
• Cisco Unified Workforce Optimization Error Code Dictionary
• Cisco Unified Workforce Optimization Recording and Quality Management Troubleshooting Guide

Removed and Unsupported Features

This release has no removed or unsupported features.

Third-party Software Impacts

This release has no third-party software impacts.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
41
 Cisco Unified Workforce Quality Management
Third-party Software Impacts

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
42
 CHAPTER 9
Caveats
• Caveat Queries by Product, page 43

Caveat Queries by Product

Bug Search Tool

If you have an account with Cisco.com, you can use the Bug Search tool to find caveats of any severity for
any release. Access the Bug Search tool at https://www.cisco.com/cisco/psn/bssprt/bss. Enter the bug identifier
in the search box, and press return or click Search.
To access a list of open caveats and resolved caveats (rather than an individual caveat) for a particular product
or component, see the relevant sections later in these notes.
You can also choose your own filters and criteria in the tool to see a specific subset of caveats, as described
in the following table.

If you choose this in Releases And you choose this in Status A list of the following caveats appears
Affecting or Fixed in these Open Any caveat in an open state for the
Releases release or releases you select.
OR
Affecting these Releases

Fixed in these Releases Fixed Any caveat in any release with the fix
applied to the specific release or
releases you select.

Affecting or Fixed in these Fixed Any caveat that is either fixed or occurs
Releases in the specific release or releases you
select.

Affecting these Releases Fixed Any caveat that occurs in the release or
releases you select.

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
43
 Caveats
Severity 3 or Higher Caveats for Release 11.0

Severity 3 or Higher Caveats for Release 11.0

Use the following links to the Bug Search Tool to view a list of Severity 3 or higher caveats for each product
or component for the current release. You can focus the result set by setting more filters in the tool.

Note If the list of caveats does not automatically appear when you open the browser, refresh the browser.

Cisco Unified Contact Center Express

https://tools.cisco.com/bugsearch/
search?kw=*&pf=prdNm&pfVal=270569179&rls=11.0(1)&sb=anfr&svr=3nH&srtBy=byRel&bt=custV

Cisco Unified Intelligence Center

https://tools.cisco.com/bugsearch/
search?kw=*&pf=prdNm&pfVal=282163829&rls=11.0(1)&sb=anfr&svr=3nH&srtBy=byRel&bt=custV

Cisco Finesse
https://tools.cisco.com/bugsearch/
search?kw=*&pf=prdNm&pfVal=283613135&rls=11.0(1)&sb=anfr&svr=3nH&srtBy=byRel&bt=custV

Cisco MediaSense
https://tools.cisco.com/bugsearch/
search?kw=*&pf=prdNm&pfVal=283613140&rls=11.0(1)&sb=anfr&svr=3nH&srtBy=byRel&bt=custV

Cisco Social Miner

https://tools.cisco.com/bugsearch/
search?kw=*&pf=prdNm&pfVal=283613136&rls=11.0(1)&sb=anfr&svr=3nH&srtBy=byRel&bt=custV

Cisco Unified Workforce Optimization Workforce Management

https://tools.cisco.com/bugsearch/
search?kw=*&pf=prdNm&pfVal=286288929&rls=11.0(1)&sb=anfr&svr=4nH&srtBy=byRel&bt=custV

Cisco Unified Workforce Optimization Quality Management

https://tools.cisco.com/bugsearch/
search?kw=*&pf=prdNm&pfVal=286288919&rls=11.0(1)&sb=anfr&svr=4nH&srtBy=byRel&bt=custV

Release Notes for Unified Contact Center Express Solution Release 11.0(1)
44