Scribd Logo
Upload

Welcome to Scribd!

  • 353 views

    EtpPrD0ATC-1000 Quick Start Guide

    Uploaded by

    dung110baclieu
    atc6

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    EtpPrD0ATC-1000 Quick Start Guide

    Uploaded by

    dung110baclieu
    353 views1 page
    atc6

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    atc6

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    353 views1 page

    EtpPrD0ATC-1000 Quick Start Guide

    Uploaded by

    dung110baclieu
    atc6

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 1

    Copyright © 2014 Reserved by ATC Technology, All Rights Reserved

     ATC-1000 10/100 Port t connect to Ethernet card use coss-Through 5. Configure the ATC-1000
    Quick Start Guide Cable as figure2
     Use this section to set up your computer to assign it a static IP
    TCP/IP TO RS-232/422/485 CONVERTER
    address in the 192.168.2.2 to 192.168.2.254 range with a subnet
    MODEL ATC-1000
    mask of 255.255.255.0. This is necessary to ensure that your
    computer can communicate with your ATC-1000. Your computer
    must have an Ethernet card and TCP/IP installed. TCP/IP should
    already be installed on computer using Windows 98/2000/XP and
    Figure2 later operating systems.
    RS-232 Assignment: (DB9 Male）  Open your web browser and type http://192.168.2.1 in the browser’s
    （DB9Male） Signal I/O address box. This address is the factory set IP Address of your
    PIN2 RXD IN
    PIN3 TXD OUT ATC-1000. Press “Enter”.
    PIN5 GND -  The “Username and Password required” prompt box will appear.
    1. Check Package Content RS-422/485 Assignment:（Six Terminal from left） Typing “admin” (default username) in the Username field and typing
     ATC-1000 Serial Server 1Pcs Terminal “system” (default password) in the Password field. Click “OK”. The
    1 2 3 4 5 6
    No
     Documentation and software CD 1Pcs RS-422 T+ T- R+ R- VIN GND setup screen will then appear.
     Quick installation guide (printed) 1Pcs RS-485 485+ 485- - - VIN GND

     Ext power adapter 1Pcs


     Connect the power adapter to ATC-1000 and other apply power.
    Power from other device.(+9--+24V@500-100mA)。
    2.Hardware Installation
     Connect an Ethernet cable to ATC-1000 unit if connecting to a 3. LED indication
    switch or cross-over direct to the PC as figure1
    LINK Indicate Ethernet link status,turn on means connected
    ACT Data transmitting between serial port and Ethernet
    PWR Indication Power status

    4.Software Installation
     Insert the software CD and search for such as F:/Driver/ ATC-1000
    folder to run VCOMSETUP.
    Figure1 Note: Be sure you have administrative rights &disable firewalls in windows
    XP
    Shenzhen ATC Technology Co., Ltd Tel: +86-755-8345 2531 Fax: +86-755-2899 8985 E-mail: [email protected] Web-Site: www.szatc.com

    You might also like