Owner’s

Manual
41” FOLDING POWER RACK

This Product is Distributed Exclusively by

Titan Distributors Inc
141 Eastley St. Ste. 113 Collierville, TN 38017
Customer Service
800 - 605 - 8241
www.titan.fitness

Downloaded from www.Manualslib.com manuals search engine

 FOLDING POWER RACK
PARTS LIST
14 3
To begin, match up
all the parts with
the following parts 4
diagrams:

5 13

BOX 1
1 11
BOX 2
10

6 9

(8) Hex Bolt M16x110 (8) Hex Nut M16

3 7 8

(8) Flat Washer (8) Spring Washer

DIAGRAM NO. PACKAGE NO. PART NUMBER DESCRIPTION QTY

1 1 P400181-1 Upright Post 2
2 2 P400182-2 HD J-Hook 4
3 1&2 P400182-3 Long Side Bracing + Short Hinge 2
4 2 P400182-4 Short Side Bracing + Long Hinge 2
5 2 P400182-5 Hinge Pin 4
6 2 P400182-6 Hex Bolt M16x110 8
7 2 P400182-7 Flat Washer 8
8 2 P400182-8 Spring Washer 8
9 2 P400182-9 Hex Nut 8
10 2 P400182-10 Pin Lock 2
11 2 P400182-11 Cotter Pin 4
12 1 P400181-12 Post End Cap 2
13 2 P400182-13 Pull Up Bar Pins 2
14 1 P400181-14 Pullup Bar 1

Downloaded from www.Manualslib.com manuals search engine

 PLEASE NOTE
Two 2” x 10” stringers must be mounted into a minimum of four studs.

The vertical center of the top stringer should be

mounted 76” from level ground.

The vertical center of the bottom stringer should be

mounted 7.25” from level ground.

NECESSARY HARDWARE MAY VARY ACCORDING TO YOUR MOUNTING

SURFACE. CONSULT YOUR LOCAL HARDWARE STORE FOR THE PROPER
MOUNTING HARDWARE.

Downloaded from www.Manualslib.com manuals search engine

 BUILD ON A FLAT AND LEVEL SURFACE.

STEP 1
 Attach LONG SIDE BRACING + SHORT HINGE (3) to one
UPRIGHT POLE (1) using four HEX BOLTS M16x110 (6), four
FLAT WASHERS (7), four SPRING WASHERS (8), and four
HEX NUTS (9).
 Attach SHORT SIDE BRACING + LONG HINGE (4) to the other
UPRIGHT POLE (1) using the same hardware described in
the previous step.
 Slide the four HINGE PINS (5) in through the top and the
four COTTER PINS (11) through the bottom.
NOTE: UHMW padding is at the bottom of the UPRIGHT POLES (1).

TOP BOTTOM

Downloaded from www.Manualslib.com manuals search engine

 STEP 2
 Attach PULLUP BAR (14) to the top of the UPRIGHT POLES
(1) using two PULL UP BAR PINS (13) and two PIN LOCKS
(10).

Downloaded from www.Manualslib.com manuals search engine

 STEP 3
 Mount the SIDE BRACINGS + HINGES (3 & 4) to your wall
using the pictured measurements.
 NOTE: The 2 pcs of (3) should be on the same side aligned
vertically and the 2 pcs of (4) should be on the other side
aligned vertically. This will allow the rack to fold over itself.
 When mounting each SIDE BRACING + HINGES (3 & 4), the
two holes are each spaced 6.4”.
 The mounting holes on the top two SIDE BRACINGS +
HINGES (3 & 4) are 76” from level ground.
 The mounting holes on the bottom two SIDE BRACINGS +
HINGES (3 & 4) are 7.25” from level ground.
 The inside holes should be should be spaced 41.5” from the
center of each hole.

NOTICE INSIDE HOLES - 41.5”

TOP HOLE TO GROUND - 76”

TEST FIT YOUR FOLDING
POWER RACK AT THE
PROVIDED MEASUREMENTS.
CHECK FOR CLEARANCE
WHILE SLIDING THE RACK
OPEN AND CLOSED. SEE THE
TROUBLESHOOTING CHART
ON THE NEXT PAGE FOR ANY
NECESSARY ADJUSTMENTS.
6.4”

Downloaded from www.Manualslib.com manuals search engine

 TROUBLESHOOTING
PROBLEM PROBABLE CAUSE SOLUTION
Rack slides right, but not Top mount is slightly to the Move top mount slightly
left. left of the bottom mount. to the right.

Rack slides left, but not Top mount is slightly to the Move top mount slightly
right. right of the bottom mount. to the left.

Rack is too high when Either wall or floor is not Add a thin spacer behind
open, but not when closed. level. the upper mounts.
(wall and floor is greater
than 90°)

Rack is too low when open, Either wall or floor is not Slightly raise all mounting
but not when closing. level. points on the wall.
(wall and floor is less than Add a thin spacer behind
90°) the lower mounts.

Rack is too high when both, Rack is mounted too high. Lower all mounting points
open and closed. on the wall.

Rack is too low when both, Rack is mounted too low. Raise all mounting points
open and closed. on the wall.

The provided The upper and lower side Upper side bracing:
measurements are bracings are not mounted in 6th and 9th from the top
substantially inaccurate. the suggested upright holes.
Lower side bracing:
2nd and 5th from the
bottom

Downloaded from www.Manualslib.com manuals search engine

 50”

Features
 Steel J-Hooks
91”
 2"x3" steel tubes
 Powder coated durable finish
 Laser cut for precise fit

Specifications
 Weight: 175 lbs
 Height: 91"
 Opening: 50"
 Depth: 41.5"
 Dimensions: (H)91" x (W)50" x (L)44.5"
 Material: Steel

WARNING
Exercise can present a health risk. Consult a physician before beginning any exercise
program with this equipment. If you feel faint or dizzy, immediately discontinue use
of this equipment. Serious bodily injury can occur if this equipment is not assembled
and used correctly. Serious bodily injury can occur if all instructions are not followed.
Keep others and pets away from equipment when in use. Always make sure all bolts
and nuts are securely tightened prior to each use. Follow all safety instructions in
this manual.

TITAN FITNESS
141 Eastley St. Ste. 113 Collierville, TN 38017 (800) 605-8241
www.titan.fitness E-MAIL: [email protected]

Downloaded from www.Manualslib.com manuals search engine