ALLDATA Online - 2002 Chevrolet Impala V6-3.4L VIN E - Intake Manifold Replacem...

Page 1 of 15

Home | Account | Contact ALLDATA | Log Out | Help TINO TORRES

Select Vehicle | New TSBs | Technician's Reference Component Search: OK

Conversion Calculator

2002 Chevrolet Impala V6-3.4L VIN E

Vehicle Level Engine, Cooling and Exhaust Engine Intake Manifold Service and Repair Intake
Manifold Replacement (Lower)

Intake Manifold Replacement (Lower)

Notes

Intake Manifold Replacement - Lower

Removal Procedure

1. Disconnect the negative bakery.

2. Remove the upper intake manifold.
3. Remove the left valve rocker arm cover.
4. Remove the right valve rocker arm cover.

Zoom Sized for Print

5. Disconnect the Engine Coolant Temperature (ECT) sensor electrical

connector.

http://www.alldatapro.com/alldata/PRO~V151303436~C36240~R0~OD~N/0/86372027/8... 1/28/2010
ALLDATA Online - 2002 Chevrolet Impala V6-3.4L VIN E - Intake Manifold Replacem... Page 2 of 15

Zoom Sized for Print

6. Disconnect and remove the fuel injector and the Manifold Absolute Pressure
(MAP) sensor wiring harnesses.

Zoom Sized for Print

7. Remove the fuel pipe clip bolt.

http://www.alldatapro.com/alldata/PRO~V151303436~C36240~R0~OD~N/0/86372027/8... 1/28/2010
ALLDATA Online - 2002 Chevrolet Impala V6-3.4L VIN E - Intake Manifold Replacem... Page 3 of 15

Zoom Sized for Print

8. Remove the fuel pipe clip.

Zoom Sized for Print

9. Remove the fuel feed pipe from the fuel injector rail.

http://www.alldatapro.com/alldata/PRO~V151303436~C36240~R0~OD~N/0/86372027/8... 1/28/2010
ALLDATA Online - 2002 Chevrolet Impala V6-3.4L VIN E - Intake Manifold Replacem... Page 4 of 15

Zoom Sized for Print

10. Remove the fuel return pipe from the fuel injector rail.

Zoom Sized for Print

11. Remove the fuel injector rail.

12. Remove the power steering pump from the front engine cover and
reposition.

http://www.alldatapro.com/alldata/PRO~V151303436~C36240~R0~OD~N/0/86372027/8... 1/28/2010
ALLDATA Online - 2002 Chevrolet Impala V6-3.4L VIN E - Intake Manifold Replacem... Page 5 of 15

Zoom Sized for Print

13. Remove the heater inlet pipe with heater hose from the lower intake manifold
and reposition.
14. Remove the radiator inlet hose from the engine.

Zoom Sized for Print

15. Remove the thermostat bypass hose from the thermostat bypass pipe and lower
intake manifold pipe.

http://www.alldatapro.com/alldata/PRO~V151303436~C36240~R0~OD~N/0/86372027/8... 1/28/2010
ALLDATA Online - 2002 Chevrolet Impala V6-3.4L VIN E - Intake Manifold Replacem... Page 6 of 15

Zoom Sized for Print

16. Remove the lower intake manifold bolts.

17. Remove the lower intake manifold.
18. Remove the valve rocker arms and pushrods.

Zoom Sized for Print

19. Remove the lower intake manifold gaskets and seals.

20. Clean the lower intake manifold gasket mating surfaces.
21. Remove and clean all the RTV sealant from the lower intake manifold and
the engine block (1).

http://www.alldatapro.com/alldata/PRO~V151303436~C36240~R0~OD~N/0/86372027/8... 1/28/2010
ALLDATA Online - 2002 Chevrolet Impala V6-3.4L VIN E - Intake Manifold Replacem... Page 7 of 15

Zoom Sized for Print

22. Remove the ECT sensor.

Zoom Sized for Print

23. Remove the water outlet bolts.

24. Remove the water outlet.

http://www.alldatapro.com/alldata/PRO~V151303436~C36240~R0~OD~N/0/86372027/8... 1/28/2010
ALLDATA Online - 2002 Chevrolet Impala V6-3.4L VIN E - Intake Manifold Replacem... Page 8 of 15

Zoom Sized for Print

25. Remove the thermostat.

Installation Procedure

Zoom Sized for Print

1. Install the thermostat.

2. Install the water outlet. Notice: Refer to Fastener Notice in Service
Precautions. See: Service Precautions

http://www.alldatapro.com/alldata/PRO~V151303436~C36240~R0~OD~N/0/86372027/8... 1/28/2010
ALLDATA Online - 2002 Chevrolet Impala V6-3.4L VIN E - Intake Manifold Replacem... Page 9 of 15

Zoom Sized for Print

3. Install the water outlet bolts. Tighten the bolts to 25 Nm (18 ft. lbs.).

Zoom Sized for Print

4. Install the ECT sensor. Tighten the sensor to 23 Nm (17 ft. lbs.).

http://www.alldatapro.com/alldata/PRO~V151303436~C36240~R0~OD~N/0/86372027/8... 1/28/2010
ALLDATA Online - 2002 Chevrolet Impala V6-3.4L VIN E - Intake Manifold Replace... Page 10 of 15

Zoom Sized for Print

5. Apply 8 - 12 mm (0.08 - 0.11 inch) bead of RTV Sealer, GM P/N 12345739

Canadian P/N 10953541 or equivalent, on each ridge where front and rear of
the lower intake manifold contact the engine block (1).
6. Install the lower intake manifold gaskets.
7. Install the valve rocker arms and pushrods.

Zoom Sized for Print

8. Install the lower intake manifold.

9. Apply sealant, GM P/N 12345382 Canadian P/N 10953489 to the threads of
the bolts. Notice: An oil leak may result if the vertical bolts are not tightened
before the diagonal bolts.

http://www.alldatapro.com/alldata/PRO~V151303436~C36240~R0~OD~N/0/86372027/8... 1/28/2010
ALLDATA Online - 2002 Chevrolet Impala V6-3.4L VIN E - Intake Manifold Replace... Page 11 of 15

Zoom Sized for Print

10. Install NEW lower intake manifold bolts. Revised Updated Torque
Specification, Bulletin #vss20030024 The torque specification is a 2-step
process; tighten the vertical lower intake manifold bolts (the four middle
ones) to 7 Nm (62 lb in). Tighten the diagonal lower intake manifold bolts
(two on each end) to 7 Nm (62 lb in). Tighten the vertical lower intake
manifold bolts (the four middle ones) to 13 Nm (115 lb in). Tighten the
diagonal lower intake manifold bolts (two on each end) to 25 Nm (18 lb ft).

Zoom Sized for Print

11. Install the thermostat bypass hose to the thermostat bypass pipe and lower intake
manifold pipe.
12. Install the radiator inlet hose to the engine.

http://www.alldatapro.com/alldata/PRO~V151303436~C36240~R0~OD~N/0/86372027/8... 1/28/2010
ALLDATA Online - 2002 Chevrolet Impala V6-3.4L VIN E - Intake Manifold Replace... Page 12 of 15

Zoom Sized for Print

13. Install the heater inlet pipe and heater hose to the lower intake manifold.
14. Install the power steering pump to the front engine cover.

Zoom Sized for Print

15. Install the fuel injector rail.

http://www.alldatapro.com/alldata/PRO~V151303436~C36240~R0~OD~N/0/86372027/8... 1/28/2010
ALLDATA Online - 2002 Chevrolet Impala V6-3.4L VIN E - Intake Manifold Replace... Page 13 of 15

Zoom Sized for Print

16. Install the fuel return pipe to the fuel injector rail.

Zoom Sized for Print

17. Install the fuel feed pipe to the fuel injector rail.

http://www.alldatapro.com/alldata/PRO~V151303436~C36240~R0~OD~N/0/86372027/8... 1/28/2010
ALLDATA Online - 2002 Chevrolet Impala V6-3.4L VIN E - Intake Manifold Replace... Page 14 of 15

Zoom Sized for Print

18. Install the fuel pipe clip.

Zoom Sized for Print

19. Install the fuel pipe clip bolt. Tighten the bolt to 8 Nm (71 inch lbs.).

http://www.alldatapro.com/alldata/PRO~V151303436~C36240~R0~OD~N/0/86372027/8... 1/28/2010
ALLDATA Online - 2002 Chevrolet Impala V6-3.4L VIN E - Intake Manifold Replace... Page 15 of 15

Zoom Sized for Print

20. Install and connect the fuel injector and the MAP sensor wiring harnesses.

Zoom Sized for Print

21. Connect the ECT sensor electrical connector.

22. Install the right valve rocker arm cover.
23. Install the left valve rocker arm cover.
24. Install the upper intake manifold.
25. Connect the negative battery cable.
26. Inspect for leaks.

© 2010 ALLDATA LLC. All rights reserved.

Terms of Use

http://www.alldatapro.com/alldata/PRO~V151303436~C36240~R0~OD~N/0/86372027/8... 1/28/2010