Scribd
Upload
689 views1 page

GD&T Reference Chart

This document provides a reference chart for geometric tolerancing per the ASME Y14.5 M-1982 standard. The chart lists various geometric characteristics like straightness, flatness, circularity, and others. It indicates whether each characteristic applies to surfaces or size, can be modified by maximum material condition, and is affected by datums, bonus tolerances, or shift.

Uploaded by

Zdravko Vidakovic
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
689 views1 page

GD&T Reference Chart

This document provides a reference chart for geometric tolerancing per the ASME Y14.5 M-1982 standard. The chart lists various geometric characteristics like straightness, flatness, circularity, and others. It indicates whether each characteristic applies to surfaces or size, can be modified by maximum material condition, and is affected by datums, bonus tolerances, or shift.

Uploaded by

Zdravko Vidakovic
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Geometric tolerancing reference chart (per ASME Y14.

5 M-1982)

Relevant feature Modified by Affected by


Virtual
Geometric Unicode
Type of Symbo conditio Reference
characteristic characte
control l n s datum
s r Surfac Of siz Bonu
affected Ⓜ Ⓢ Shift
e e s

⏤ Of
Form Straightness[3]
U+23E4
Yes Yes Of size[a] No
size[a]
No[c] Ⓜ[d] No

Form Flatness[4] ⏤ Yes No No No No No[c] No No


U+23E5

Form Circularity[4] ○ Yes No No No No No[c] No No


U+25CB

Form Cylindricity ⌭ Yes No No No No No[c] No No


U+232D

Profile Profile of a line ⌒ Yes No No Yes[e] No No[c] No Datum, Ⓜ[


U+2312 b]

Profile
Profile of a ⌓ Yes No No Yes[e] No No[c] No Datum, Ⓜ[
surface U+2313 b]

Orientatio Perpendicularit ⟂ Yes Yes Of size[a] Yes


Of
No[c] Ⓜ[d] Datum, Ⓜ[
n y U+27C2 size[a] b]

Orientatio
Angularity ∠ Yes Yes Of size[a] Yes
Of
No[c] Ⓜ[d] Datum, Ⓜ[
n U+2220 size[a] b]

Orientatio
Parallelism ∥ Yes Yes Of size[a] Yes
Of
No[c] Ⓜ[d] Datum, Ⓜ[
n U+2225 size[a] b]

Location Symmetry[f][g] ⌯ No Yes Yes Yes No No No No


U+232F

Location Position ⌖ No Yes Yes Yes Yes Yes Ⓜ[d] Datum, Ⓜ[


U+2316 b]

Location Concentricity[f] ◎ No Yes Yes Yes No No[c] No No


U+25CE

Run-out Circular run-out ↗ Yes Yes Of size[a] Yes No No[c] No No


U+2197

Run-out Total run-out ⌰ Yes Yes Of size[a] Yes No No[c] No No


U+2330

1. ^ Jump up to:a b c d e f g h i j When applied to a feature of size.


2. ^ Jump up to:a b c d e f g When a datum feature of size is referenced with the maximum material condition modifier.
3. ^ Jump up to:a b c d e f g h i j k l Automatically[b]
4. ^ Jump up to:a b c d e When an maximal material condition modifier is used.
5. ^ Jump up to:a b Can also be used as a form control without a datum reference.
6. ^ Jump up to:a b In the 2018 revision, both concentricity and symmetry were eliminated and are no longer supported.
7. ^ The symmetry symbol's characteristics were not included in the version of the chart that this chart is derived from. The symmetry symbol was dropped from the
Y14.5M standard around 1982 and re-added around 1994.

You might also like