Scribd Logo
Upload

Welcome to Scribd!

  • 103 views

    SKF Mount - 22318 EJA - VA405 - Hot Mounting - Housing

    Uploaded by

    cumtjerry
    This document provides instructions for hot mounting an SKF 22318 EJA/VA405 bearing in a housing. The key steps are: 1. Clean and prepare the bearing, housing, and other components. 2. Heat the housing to 80-90°C using an induction heater or oven. 3. Push the bearing into the heated housing and hold it until it grips. Additional recommendations include filling the housing with the appropriate amount of grease after mounting.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    SKF Mount - 22318 EJA - VA405 - Hot Mounting - Housing

    Uploaded by

    cumtjerry
    103 views3 pages
    This document provides instructions for hot mounting an SKF 22318 EJA/VA405 bearing in a housing. The key steps are: 1. Clean and prepare the bearing, housing, and other components. 2. Heat the housing to 80-90°C using an induction heater or oven. 3. Push the bearing into the heated housing and hold it until it grips. Additional recommendations include filling the housing with the appropriate amount of grease after mounting.

    Original Title

    SKF Mount - 22318 EJA_VA405 - Hot mounting - Housing

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for hot mounting an SKF 22318 EJA/VA405 bearing in a housing. The key steps are: 1. Clean and prepare the bearing, housing, and other components. 2. Heat the housing to 80-90°C using an induction heater or oven. 3. Push the bearing into the heated housing and hold it until it grips. Additional recommendations include filling the housing with the appropriate amount of grease after mounting.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    103 views3 pages

    SKF Mount - 22318 EJA - VA405 - Hot Mounting - Housing

    Uploaded by

    cumtjerry
    This document provides instructions for hot mounting an SKF 22318 EJA/VA405 bearing in a housing. The key steps are: 1. Clean and prepare the bearing, housing, and other components. 2. Heat the housing to 80-90°C using an induction heater or oven. 3. Push the bearing into the heated housing and hold it until it grips. Additional recommendations include filling the housing with the appropriate amount of grease after mounting.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    5/27/2019 SKF Mount - 22318 EJA/VA405 - Hot mounting - Housing

    Mounting procedure
    Designation: 22318 EJA/VA405
    Mounting Method: Hot mounting
    Interference Fit: Housing

    Mounting preparations

    Mount the bearing in a clean environment, or take steps to protect the bearing and mounting
    position from contaminants like dust, dirt and moisture. Check housings, shafts and other
    components of the bearing arrangement to make sure that they are clean and not damaged.

    Leave bearings in their original packaging until mounting so that they do not get dirty.

    Check the dimensional and geometrical tolerances of all components that will be in contact with
    the bearing.

    Typically, the diameter of cylindrical housing seats is checked using an internal gauge at four
    positions in three planes. Use the form provided here, something similar, to record the
    measurements before mounting and for future quality assurance purposes.

    1 2 3 A
    D B
    C

    https://mount.skf.com/search-result?lang=en 1/3
    5/27/2019 SKF Mount - 22318 EJA/VA405 - Hot mounting - Housing

    Carefully read all of the instructions before starting work. The instructions may contain alternative
    tools and measuring methods. Illustrations are not always proportional and do not always show
    the exact design. The instructions are valid for SKF bearings only. Where tool recommendations
    are made, check the actual dimensions against the bearing and any other components that may
    interfere with the use of the tool.

    Mounting and dismounting of rolling bearings may involve the handling of heavy weights, the use
    of tools and other devices, and the use of high pressure oil. To avoid accidents, injuries or damage
    to property, please carefully follow the prescribed methods.

    Wipe the preservative from the bore and outside diameter of the bearing.

    If the bearing is to be grease lubricated and used at very high or very low temperatures, or the
    grease is not compatible with the preservative, wash and carefully dry the bearing.

    Coat the bearing outside surface with a thin layer of light oil.

    Mounting procedure
    If possible, heat the housing with an induction heater. Otherwise, use an oven or a propane burner.

    Normally a housing temperature of 80 to 90 °C (145 to 160 °F) above that of the bearing is sufficient for mounting.

    Wear clean protective gloves when handling the hot housing.

    https://mount.skf.com/search-result?lang=en 2/3
    5/27/2019 SKF Mount - 22318 EJA/VA405 - Hot mounting - Housing

    1. Push the bearing along the housing seat to its abutment and hold the bearing in position until it
    grips.

    Additional recommendations

    Normally the bearing should be filled completely with grease unless it is to operate at high speeds, in
    which case the free space in the housing should only be partially filled (30 to 50%) with grease. In non-
    vibrating applications, where bearings are to operate at very low speeds and good protection against
    contamination is required, SKF recommends filling up to 90% of the free space in the housing with
    grease.

    The SKF grease meter LAGM 1000E helps with keeping track of the supplied quantity.

    For information on selecting a suitable grease, considering actual operating conditions, refer to the
    SKF Quick grease selection guide.

    If the bearing is to be oil lubricated then use sufficient quantity of the correct oil.

    If the bearing is to be grease lubricated, add the grease now.

    Applying the recommended values prevents the inner ring from creeping, but does not ensure correct
    radial internal clearence in operation. Additional influences from the bearing housing fit and
    temperature differences between the inner and outer rings, must be considered carefully when
    selecting the bearing radial internal clearance class. For additional information, contact the SKF
    application engineering service.

    https://mount.skf.com/search-result?lang=en 3/3

    You might also like