NVF5 Series Inverter Quick Start-Up Wizard

1.Safety Precautions
The purpose of this quick start-up wizard is to guide you
to complete the basic installation 、 wiring and basic
parameters setting、commissioning and troubleshooting for
NVF5 series inverter products. For more information, please
refer to the user manual or scan the QR code to get the user
materials. This NVF5 series products have been strictly
tested and packaged before leaving the factory. If abnormal
information such as inverter damage and wrong delivery is
found, please contact Chint channel or the relevant office
or call Chint oversea hotline：400-1177-797
Attention：
 It is not permitted to conduct unauthorized modification in case of the danger of
fire/electric shock and other hurt！
 Installation must be conducted by qualified personnel in case of the danger of
electric shock！
 Please install the inverter on the metal equipmen(supplementary enclosure) or
other non-combustible objects in case of the danger of fire!
 It is not permitted to place combustibles nearby in case of the danger of fire!
 The products should be installed with either fuses or an input circuit breaker
Danger between the inverter and power supply in case of danger of fire!
 It is not permitted to install the inverter in an environemnt containing explosive
gases in case of the danger of explosion!
 It is not permitted to insall the inverter at a place directly exposed in sunlight in
case of the danger of equipment damage!
 It is not permitted to install the inverter on occasions where water splashing in
case of the danger of equipment damage!
Installation Dimensions：

Figure 1-1 Figure 1-2

 2.Catalog Number Description、Product Models、Dimensions and Weights
NVF5 0.4 / T D 2 B

Number of
Product Applicable T: Universal Inverter Input Input Voltage Brake Unit
Model Motor Power Model Phases Rating
B: Standard
(kW)
D: Single 2：230V Embedded
Phase
4：380V~ 440V Blank: No
S: Three Embedded
Phases

W D W1 W D W1 d

H1

H1
H

H
NVF5-0.4/TD2~NVF5-2.2/TD2、NVF5-0.4/TD2-B~ NVF5-3.7/TS4-B～NVF5-7.5/TS4-B
NVF5-2.2/TD2-B and NVF5-0.4/TS4-B~NVF5-2.2/TS4-B product appearance and installation
product appearance and installation dimension diagram dimension diagram
Figure 2-1 Figure 2-2
Unit (mm)
Adaptive Output
Brake Mounting Weight
Catalog No. Motor Current
Unit W H D W1 H1 Hole kg
kW A
d
Single Phase AC 230V
NVF5-0.4/TD2
0.4 2.5
NVF5-0.4/TD2-B
NVF5-0.75/TD2
0.75 5 75 148 125.2 64 137.5 Φ5.3 1.2
NVF5-0.75/TD2-B Optional
NVF5-1.5/TD2 (embedded)
1.5 7.5
NVF5-1.5/TD2-B
NVF5-2.2/TD2
2.2 10 75 148 146.7 64 137.5 Φ5.3 1.25
NVF5-2.2/TD2-B
Three Phase AC 380V~440V
NVF5-0.4/TS4-B 0.4 1.5
NVF5-0.75/TS4-B 0.75 2.7
75 148 125.2 64 137.5 Φ5.3 1.03
NVF5-1.5/TS4-B 1.5 4.2
Standard
NVF5-2.2/TS4-B 2.2 5.8
(embedded)
NVF5-3.7/TS4-B 3.7 10.5
89.5 206 149.2 78.5 196.8 Φ5.5 1.79
NVF5-5.5/TS4-B 5.5 13
NVF5-7.5/TS4-B 7.5 17 118 216 163.4 105 205 Φ6 2.78
3.Installation and Wiring
3.1 Power Terminal Description
（1） Single Phase 230V（NVF5-0.4/TD2～2.2/TD2 （2） Three Phase380V（NVF5-0.4/TS4-B～
and NVF5-0.4/TD2-B～2.2/TD2-B） 7.5/TS4-B）

NVF5-0.4/TD2～2.2/TD2 and NVF5-0.4/TS4-B～7.5/TS4-B

NVF5-0.4/TD2-B～2.2/TD2-B Power Terminal Power Terminal
Figure 3-1 Figure 3-2
Terminal Name Description
Main Power Supply The three-phase AC input terminals ,connecting
R、S、T
Input with the power grid
Main Power Supply The Single-Phase AC input terminals ,connecting
L1、L2
Input with the power grid
The three-phase AC output terminals ,connecting
U、V、W Inverter Output
with the AC motor
Grounding Grounding terminals,ensure reliable grounding
P+ P- DC Bus Terminals Single phase type DC+ and DC-
P B Outer Brake Resistor Three phase type brake resistor terminals
P+ B Terminals Single phase type brake resistor terminals
3.2 Power terminal and I/O terminal block diagram
Brake resistor
QF
Single-phase input poweer
230V 50/60Hz
Three-phase input power
380V~440V 50/60Hz Main circuit terminal
Motor grounding
Power grounding
Control circuit terminal

Programmable relay outputs

Programmable
Multifunction
Input Programmable open collector
high-speed output

Analog input power supply Analog output

Output V:(0～10)V
2 x Analog input
V:(-10～10)V I:(0～20)mA or (4～20)mA
I:(0～20)mA or (4～20)mA AO A11
Analog input common
AOI AOV I1 V1 J2 Multifunction interface

J2、J3 Multifunction extension card interface

J3 Multifunction interface

RS485 communication

Figure 3-3
AO Dip Switch：Left， （0~20）mA or （4~20）mA Analog Current Ouput；Right，（0~10）
V Analog Voltage Output.
（0~20）mA or （4~20）mA Analog Current input；Right，
AI1 Dip Swith：Left， （0~10）VAnalog
Voltage input.
AI2：Current Output need to be customized.
Wiring Demonstration：

4.Integral Keypad
4.1 Integral Keypad and Indicators
 Figure 4-1
4.2 Combination key Function Description
Key Description
Parameter Menu Mode Selection（F7.11）
1、 Simple Parameter Menu Mode（U-1）
＋
2、 Custom Parameter Menu Mode（U-2）
3、 Engineering Parameter Menu Mode（U-3）
The system is under the main Lock Combinational Key
interface
＋
In custom menu mode,in menu level Add custom parameters
one
The system is under the main Unlock Combinational Key
interface
＋
In custom menu mode,in next level Delete custom parameters
menu
4.3 Parameter Menu Mode Demonstration
Simple parameter menu mode demonstration：
Below example is how to set parameter F0.05 from 5.00Hz to 10.00Hz in Simple Parameter
Menu Mode.
Change parameter
Ready status: Parameter menu No.
mode information Parameters
5.00Hz flash Press using
Press
2S
5.00 U-1 later F0.00
F0 F0.05
Press

5.00
Press Press
Press
` Press Shift
key

Press Press Press Shift

Press key

10.00 F0.14 10.00 5.00 5.00

Press

Figure 4-2 Simple Menu Mode Parameter Setting

5. Simple Parameter Menu and Commissioning Process
5.1 Simple Parameter Menu List
Code Name Attribute Parameter Description Default
0：Sensorless Vector Control
Motor Control ◎ 1：Reserve
F0.00 0
Mode
2：V/F Mode
 0：Integral Keypad
Command 1：Digital Terminal
F0.01 ○ 0
Source 2：Communication
3：Remote Panel
0：Digital Given
1：AI1
2：AI2
3：Reserve
Main 4：High Speed Pulse HDI Reference
F0.02 Frequency ○ 0
5：Preset Speed Reference
Reference
6：Simple PLC Reference
7：Close Loop PID Reference
8：Reserve
9：Potentiometer Reference
F0.05 Digital Given ○ F0.09-Min. Frequency～F0.08-Max. Frequency 5.00Hz
Accelerate Depend on
F0.14 ○ （0.0～6500.0）s
Time 1 Series
Decelerate （0.0～6500.0）s Depend on
F0.15 ○
Time 1 Series
0：No Effect
1：Fault Log Clear
2 ： Set to Factory Default （ Except Motor NP
Parameters and Parameter F7.11）
3：Reset Custom Parameter Group to Factory
Default （ Except Motor NP Parameters and
Parameter F7.11）
Parameter ◎ 4：All Parameter Reset to Factory Default
F0.20 0
Factory Default 5：Back Up Parameters
6：Using Back Up Parameters
7：Saving Back Up Parameters
Note ： Only when you are using backup
parameters,backup parameter are able to be
saved.Otherwise when power off then re-power
the inverter,except the updated parameters other
parameters are always initial value.
0：AC Induction Motor
F2.00 Motor Type ○ 1：Reserve
2：Reserve
Motor NP ◎ （0.1 ～ 1000.0） kW Depend on
F2.01
Power motor type
Motor NP ◎ 0V ～ Inverter Rated Voltage Depend on
F2.02
Voltage motor type
Motor NP Depend on
F2.03 ◎ （0.1～1000.0）A
Current motor type
Motor NP ◎ Depend on
F2.04 0.01Hz ~ F0.07
Frequency motor type
F2.05 Motor Poles ◎ 2 ～ 24 4
F2.06 Motor NP RPM ◎ （0～60000）rpm 1430rpm
0：No Operation
Motor Auto ◎ 1：Static Tune
F2.22 0
Tuning
2：Rotate Tune
1：Simple Menu Mode
Parameter
F7.11 ◎ 2：Custom Menu Mode 1
Menu Mode
3：Engineering Menu Mode
5.2 Simple Commissioning Process

Confirm the main Refer to Chapter 3 -“Installation

circuit and control and Wiring” for check correct
circuit correct wiring
After power on, the default 5.00Hz
Power on will be displayed on NVF5 integral
keypad screen normally
Select motor Set NVF5 motor control mode according
control mode by to parameter F0.00 definition. The default
parameter F0.00 mode is V/F control.

Input the correct motor nameplate

Input the correct motor data in parameter group F2
nameplate data (F2.01~F2.06)

Need motor Can disconnect

auto tuning Yes motor load?
Yes
No
No Set parameter F2.22 Set parameter F2.22
to 1, press RUN key to 2, press RUN key
to conduct static to conduct rotate
motor auto tuning motor auto tuning

If the motor runs reverse,

Run the motor at 5.00Hz and change parameter F0.06 or
check the motor running direction change the 3-phase motor
cables.
Set reference frequency by Default reference frequency is
parameter F0.05 5.00Hz. It can be changed as
required.

Set Accel. and Decel. time Set Accel.time and

Decel.time by parameter
F0.14 and F0.15
When the inverter is ready, press Run key to start
the motor without load, measure and check the 3- The output current value of
phase current balance inverter is almost the same as
the value displayed on
integral keypad of NVF5，
If the inverter is running normally without load, the
motor running direction refer
inverter can be tested with load, measure and
to parameter F0.06
confirm the 3-phase current balance, and also
confirm the current less than rated motor current

After testing completed, stop the inverter, prepare

to set other parameters as equipment required

Record the current value and parameters

After testing completed, stop the inverter

and set other parameters as required

Figure 5-1
6. Fault description and Trouble shooting
If a fault appears，Please see for an explanation of the fault code and check by yourself firstly
before asking for help from Chint or Chint channels.When you need support,please contact
Chint or Chint channels.
Code Fault Type Fault reason Action
Inverter
Accel.
E.OC1
running Low grid voltage Check the input power supply
overcurrent Directly and quickly start rotating motor Increase accel. time
Inverter Incorrect Motor Nameplate Motor auto tuning
Decel. Too small inverter power Enlarge inverter power rate
E.OC2
running Unsuitable V / F curve Adjust V/F cruve or adjust manual
overcurrent Potential Energy Load or Big Inertial Load torque boost
Inverter Accel./Decel. Time too short Add Regen. Brake Components
constant Load Fast Change Check load
E.OC3
speed running
overcurrent
 Inverter
Accel.
E.OV1
running Motor short circuit to ground
overvoltage Check motor cable
Abnormal input voltage
Check the input power supply
Inverter Motor quick start again at high speed
Start inverter when motor stop
Decel. Potential Energy Load or Big Inertial Load
E.OV2 Add Regen. Brake Components
running Increase decel. time
Increase decel. time
overvoltage Incorrect setting of Parameter ASR
Refer to Parameter Group F3
Inverter in vector control
about how to set ASR
constant Big Inertial Load
E.OV3
speed running
overvoltage
Input Lose Checking Main Power Terminal
E.SPI R.S.T lose phase
Phase Wiring
Check Input Voltage
Output Lose
E.SPO U.V.W lose phase Check Motor Cable
Phase
Check Motor and Cable
The output three-phase with
interphase short circuit or ground
short circuit Re-wire, confirm the motor
Inverter instantaneous overcurrent insulation
Fan duct blockage or fan damage See overcurrent handling
High ambient temperature Clear the fan duct or replace
Power Module
E.FO Loose I/O wiring or plug the fan
Protection
Current waveform anomaly due to output Lower ambient temperature
lose-phase and other reasons Check wiring and re-wire
Aux. power supply damage, Checking wiring
drive voltage undervoltage Asking for Chint technical support
IGBT Module Damage
Control Board Abnormal
Heat Sink High ambient temperature
E.OH1 Lower ambient temperature
Overheat Fan duct blockage
Clear the fan duct
Fan damage
Rectifier Bridge Replace the fan
E.OH2 IGBT abnormal
Overheat Asking for Chint technical support
Temperature checking circuit error
Input correct motor overload ratio
E.OL1 Motor Overload
Incorrect Motor Overload Ratio Check motor load
Motor Stall or load change frequently Select Frequency conversion
Long time low speed ruuning with excessive motor
load Check grid voltage
Low grid voltage Adjust V/F cruve or adjust manual
Inverter Unsuitable V / F curve torque boost
E.OL2 Incorrect Motor Nameplate Motor auto tuning
Overload
Excessive load Enlarge inverter power rate
Excessive DC Brake Reduce DC brake
Accel. Time too short current, increase brake time
Increase accel. time
Set Wrong Motor Data Set correct motor data
Reverse Auto Tuning is Disable Reverse
prohibited in reverse running Check motor cable
E.tE Auto Tuning Check Parameter F0.08
Poor contact of motor
connecting cable （Frequency Max.） whether is
Auto Tuning Overtime samller than rated frequency
Motor short
E.StG Motor short circuit to ground Check motor cable
circuit to ground
Check whether load loss or
Inverter Current is Smaller than the value of
E.LL Load Loss Fault parameter FE.17、FE.18、FE.19
Parameter FE.18
parameter setting