Hyperion 1300g: User's Guide

Hyperion 1300g
General Purpose Handheld Linear Scanner
User’s Guide
™
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make changes in speci-
fications and other information contained in this document without prior notice,
and the reader should in all cases consult HII to determine whether any such
changes have been made. The information in this publication does not repre-
sent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions contained
herein; nor for incidental or consequential damages resulting from the furnish-
ing, performance, or use of this material.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied, repro-
duced, or translated into another language without the prior written consent of
HII.
© 2010 Honeywell International Inc. All rights reserved.
Other product names or marks mentioned in this document may be trademarks
or registered trademarks of other companies and are the property of their
respective owners.
Web Address: www.honeywellaidc.com
Table of Contents
Chapter 1 - Getting Started

About This Manual ...................................................... 1-1
Unpacking the Scanner ............................................... 1-1
Connecting with USB .................................................. 1-1
Connecting with Keyboard Wedge .............................. 1-2
Connecting with RS-232 Serial Port............................ 1-3
Connecting with RS485............................................... 1-3
Reading Techniques ................................................... 1-4
Menu Bar Code Security Settings ............................... 1-5
Resetting the Standard Product Defaults .................... 1-5
Chapter 2 - Programming the Interface

Introduction ................................................................. 2-1
Programming the Interface - Plug and Play ................ 2-1
Keyboard Wedge................................................... 2-1
Laptop Direct Connect........................................... 2-1
IBM PS2 Keyboard................................................ 2-2
RS232 Serial Port.................................................. 2-2
RS485 ................................................................... 2-3
OPOS Mode .......................................................... 2-4
USB IBM SurePos................................................. 2-5
USB PC or Macintosh Keyboard ........................... 2-5
USB HID................................................................ 2-6
USB Serial Commands ............................................... 2-6
USB Serial Emulation............................................ 2-6
CTS/RTS Emulation .............................................. 2-6
ACK/NAK Mode..................................................... 2-7
Keyboard Country Layout ........................................... 2-8
Keyboard Wedge Modifiers ......................................... 2-9
Keyboard Style ...................................................... 2-9
Keyboard Modifiers ............................................. 2-11
i
RS232 Modifiers ........................................................ 2-13
RS-232 Baud Rate............................................... 2-13
RS-232 Word Length: Data Bits, Stop Bits, and Parity
2-14
RS-232 Handshaking................................................. 2-16
RTS/CTS ............................................................. 2-16
XON/XOFF .......................................................... 2-16
ACK/NAK ............................................................. 2-16
Chapter 3 - Input/Output Settings

Good Read Indicators.................................................. 3-1
Beeper – Good Read ............................................. 3-1
Beeper Volume – Good Read................................ 3-1
Beeper Pitch – Good Read .................................... 3-2
Beeper Duration – Good Read .............................. 3-2
Beeper Pitch – Error .............................................. 3-3
LED – Good Read ................................................. 3-3
Number of Beeps – Good Read ............................ 3-3
Good Read Delay ........................................................ 3-4
User-Specified Good Read Delay.......................... 3-4
Trigger Modes.............................................................. 3-5
Manual/Serial Trigger ............................................ 3-5
Automatic Trigger .................................................. 3-5
Presentation Mode................................................. 3-6
Continuous Illumination Mode ............................... 3-6
Hands Free Time-Out .................................................. 3-6
Reread Delay............................................................... 3-7
User-Specified Reread Delay ................................ 3-8
Centering ..................................................................... 3-8
Output Sequence Overview....................................... 3-10
To Add an Output Sequence ............................... 3-10
Other Programming Selections............................ 3-11
Output Sequence Editor ...................................... 3-11
Require Output Sequence ................................... 3-11
Output Sequence Editor ...................................... 3-13
Require Output Sequence ................................... 3-13
ii
Multiple Symbols ....................................................... 3-14
No Read .................................................................... 3-15
Video Reverse........................................................... 3-15
Chapter 4 - Data Editing

Prefix/Suffix Overview ................................................. 4-1
To Add a Prefix or Suffix ....................................... 4-1
To Clear One or All Prefixes or Suffixes................ 4-2
To Add a Carriage Return Suffix to All Symbologies4-
3
Prefix Selections.................................................... 4-3
Suffix Selections.................................................... 4-4
Function Code Transmit ........................................ 4-4
Intercharacter, Interfunction, and Intermessage Delays 4-
4
Intercharacter Delay .............................................. 4-5
User Specified Intercharacter Delay...................... 4-5
Interfunction Delay ................................................ 4-6
Intermessage Delay .............................................. 4-6
Chapter 5 - Data Formatting

Data Format Editor Introduction .................................. 5-1
To Add a Data Format........................................... 5-1
Other Programming Selections ............................. 5-3
Terminal ID Table........................................................ 5-4
Data Format Editor Commands .................................. 5-4
Send Commands................................................... 5-4
Move Commands .................................................. 5-5
Search Commands................................................ 5-5
Miscellaneous Commands .................................... 5-6
Data Format Editor ................................................ 5-8
Data Formatter ...................................................... 5-8
.............................................................................. 5-9
iii
Chapter 6 - Symbologies
Introduction .................................................................. 6-1
All Symbologies ........................................................... 6-2
Message Length .......................................................... 6-2
Codabar ....................................................................... 6-3
Codabar Start/Stop Characters ............................. 6-3
Codabar Check Character ..................................... 6-3
Codabar Concatenation ......................................... 6-4
Codabar Message Length ..................................... 6-5
Code 39 ....................................................................... 6-6
Code 39 Start/Stop Characters ............................. 6-6
Code 39 Check Character ..................................... 6-6
Code 39 Message Length...................................... 6-7
Code 39 Append .................................................... 6-7
Code 32 Pharmaceutical (PARAF) .............................. 6-8
Full ASCII............................................................... 6-9
Code 39 Code Page .............................................. 6-9
Interleaved 2 of 5 ....................................................... 6-10
Check Digit .......................................................... 6-10
Interleaved 2 of 5 Message Length ..................... 6-11
Code 93 ..................................................................... 6-12
Code 93 Message Length.................................... 6-12
Code 93 Code Page ............................................ 6-12
Straight 2 of 5 Industrial (three-bar start/stop) ........... 6-14
Straight 2 of 5 Industrial Message Length ........... 6-14
Straight 2 of 5 IATA (two-bar start/stop) .................... 6-15
Straight 2 of 5 IATA Message Length .................. 6-15
Matrix 2 of 5 ............................................................... 6-16
Matrix 2 of 5 Message Length ............................. 6-16
Code 11 ..................................................................... 6-17
Check Digits Required ......................................... 6-17
iv
Code 128................................................................... 6-18
ISBT 128 Concatenation ..................................... 6-18
Code 128 Message Length ................................. 6-19
Code 128 Code Page.......................................... 6-19
Code 128 Function Code Transmit ..................... 6-20
Telepen ..................................................................... 6-20
Telepen Output.................................................... 6-21
Telepen Message Length.................................... 6-22
UPC A ....................................................................... 6-23
UPC A Check Digit .............................................. 6-23
UPC A Number System....................................... 6-24
UPC A Addenda .................................................. 6-24
UPC A Addenda Required .................................. 6-25
UPC A Addenda Separator ................................. 6-25
UPC-A/EAN-13
with Extended Coupon Code .................................. 6-26
UPC E ....................................................................... 6-27
UPC E0 and UPC E1 .......................................... 6-27
UPC E0 and UPC E1 Expand ............................. 6-28
UPC E0 and UPC E1 Addenda Required ........... 6-28
UPC E0 and UPC E1 Addenda Separator .......... 6-29
UPC E0 Check Digit ............................................ 6-29
UPC E0 Number System..................................... 6-30
UPC E0 Addenda ................................................ 6-30
EAN/JAN 13 .............................................................. 6-31
EAN/JAN 13 Check Digit..................................... 6-31
EAN/JAN 13 Addenda......................................... 6-32
EAN/JAN 13 Addenda Required ......................... 6-32
EAN/JAN 13 Addenda Separator ........................ 6-33
ISBN Translate .................................................... 6-33
EAN/JAN 8 ................................................................ 6-33
EAN/JAN 8 Check Digit....................................... 6-34
EAN/JAN 8 Addenda........................................... 6-35
EAN/JAN 8 Addenda Required ........................... 6-35
EAN/JAN 8 Addenda Separator .......................... 6-36
v
MSI ............................................................................ 6-36
MSI Check Character .......................................... 6-36
MSI Message Length ........................................... 6-37
Plessey Code............................................................. 6-37
Plessey Message Length..................................... 6-38
GS1 DataBar Omnidirectional ................................... 6-38
GS1 DataBar Limited................................................. 6-39
GS1 DataBar Expanded ............................................ 6-39
GS1 DataBar Expanded Message Length........... 6-40
China Post Code........................................................ 6-40
Korea Post Code ....................................................... 6-42
Korea Post Message Length ............................... 6-42
Codablock F............................................................... 6-43
Codablock F Message Length ............................. 6-43
Code 49 ..................................................................... 6-44
Trioptic Code ............................................................. 6-45
GS1 Emulation........................................................... 6-45
Label Code ................................................................ 6-46
Chapter 7 - Interface Keys

Keyboard Function Relationships ................................ 7-1
Supported Interface Keys ........................................... 7-3
Chapter 8 - Utilities
To Add a Test Code I.D. Prefix to All Symbologies ..... 8-1
Show Software Revision.............................................. 8-1
Show Data Format....................................................... 8-1
Chapter 9 - Serial Programming Commands

Conventions................................................................. 9-1
vi
Menu Command Syntax.............................................. 9-1
Query Commands ................................................. 9-2
Concatenation of Multiple Commands .................. 9-2
Responses ............................................................ 9-2
Examples of Query Commands ............................ 9-3
Trigger Commands ..................................................... 9-4
Menu Commands ........................................................ 9-5
Chapter 10 - Product Specifications

Hyperion 1300g Product Specifications .................... 10-1
Chapter 11 - Maintenance
Repairs ...................................................................... 11-1
Maintenance.............................................................. 11-1
Cleaning the Device ............................................ 11-1
Inspecting Cords and Connectors ....................... 11-1
Replacing the Interface Cable ............................. 11-2
Troubleshooting ........................................................ 11-2
Chapter 12 - Customer Support

Technical Assistance ................................................ 12-1
Online Technical Assistance ............................... 12-2
Product Service and Repair ...................................... 12-2
Online Product Service and Repair Assistance... 12-3
Limited Warranty ....................................................... 12-3
Appendix A - Appendix A
Symbology Chart......................................................... A-1
ASCII Conversion Chart (Code Page 1252) ............... A-2
Code Page Mapping of Printed Bar Codes ................. A-5
vii
viii
Product Agency Compliance
USA
FCC Part 15 Subpart B Class B
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio or television technician for
help.
Caution: Any changes or modifications made to this equipment not

expressly approved by Honeywell International Inc. may void the
FCC authorization to operate this equipment.
Note: To maintain compliance with EMC Regulations, cables connected to

this device must be shielded cables. This unit has been tested with
cables less than 3 meters. Cables greater than 3 meters may not
meet class B performance.
UL Statement
UL listed: UL60950-1, 2nd Edition for I.T.E. product safety.
Note: Use only a Listed Limited Power Source (LPS) or Class 2 type power
supply with output rated 5 to 5.2Vdc, 1A.
Canada
Industry Canada ICES-003
This Class B digital apparatus complies with Canadian ICES-003. Operation
is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Note: To maintain compliance with EMC Regulations, cables connected to
this device must be shielded cables. This unit has been tested with
cables less than 3 meters. Cables greater than 3 meters may not
meet class B performance.
Note: Use only a Listed Limited Power Source (LPS) or Class 2 type power
supply with output rated 5 to 5.2Vdc, 1A.
Conformité à la règlementation canadienne

Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du
Canada. Son fonctionnement est assujetti aux conditions suivantes :
1. Cet appareil ne doit pas causer de brouillage préjudiciable.
2. Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le
brouillage pouvant causer un fonctionnement indésirable.
C-UL Statement
C-UL listed: CSA C22.2 No.60950-1-07, 2nd Edition for I.T.E. product safety.
Europe
The CE marking indicates compliance to 2004/108/EC EMC Directive
with Standards EN55022 CLASS B, EN55024, EN61000-3-2,
EN61000-3-3. In addition, complies to 2006/95/EC Low Voltage
Directive, when shipped with recommended power supply.
For CE-related inquiries, please contact:
Honeywell Imaging & Mobility Europe BV
Nijverheidsweg 9
5627 BT Eindhoven
The Netherlands
Honeywell shall not be liable for use of our product with equipment (i.e.,
power supplies, personal computers, etc.) that is not CE marked and does
not comply with the Low Voltage Directive.
Waste Electrical and Electronic Equipment
Information
Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN
PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on waste
electrical and electronic equipment (WEEE).
This product has required the extraction and use of natural resources for its
production. It may contain hazardous substances that could impact health
and the environment, if not properly disposed.
In order to avoid the dissemination of those substances in our environment
and to diminish the pressure on the natural resources, we encourage you to
use the appropriate take-back systems for product disposal. Those systems
will reuse or recycle most of the materials of the product you are disposing in
a sound way.
The crossed out wheeled bin symbol informs you that the product
should not be disposed of along with municipal waste and invites you to use
the appropriate separate take-back systems for product disposal.
If you need more information on the collection, reuse, and recycling systems,
please contact your local or regional waste administration.
You may also contact your supplier for more information on the
environmental performances of this product.
Germany
GS Mark Applicable if GS logo is marked on product to indicate

meeting geprufte Sicherheit approval.
Russia
Australia/NZ
C-Tick Statement
Conforms to AS/NZS 3548 EMC requirements.
Mexico
Applicable if NOM logo is marked on product. Conforms to

NOM-019.
South Korea
Taiwan
BSMI Standard: CNS13438, CNS14336
依據標準 : CNS13438, CNS14336
International
LED Safety Statement
LEDs have been tested and classified as “EXEMPT RISK GROUP” to the
standard: IEC 62471:2006.
CB Scheme
Certified to IEC60950-1 Second Edition I.T.E. Product Safety.
Solids and Water Protection
The devices have a rating of IP41, immunity of foreign particles and dripping
water tested to Standard EN60259.
Patents
For patent information, please refer to www.honeywellaidc.com/patents.
Required Safety Label Locations
Light Source
Item
Number,
Serial
Number
and Compliance
Revision Label location
1 Getting Started
About This Manual

This User’s Guide provides installation and programming instructions for the
Hyperion 1300g. Product specifications, dimensions, warranty, and customer
support information are also included.
Honeywell bar code scanners are factory programmed for the most common
terminal and communications settings. If you need to change these settings,
programming is accomplished by scanning the bar codes in this guide.
An asterisk (*) next to an option indicates the default setting.
Unpacking the Scanner

After you open the shipping carton containing the product, take the following
steps:
• Check for damage during shipment. Report damage immediately to the
carrier who delivered the carton.
• Make sure the items in the carton match your order.
• Save the shipping container for later storage or shipping.
Connecting with USB

A scanner can be connected to the USB port of a computer.
1. Connect the appropriate interface cable to the scanner first, then to the com-
puter.
2. The scanner beeps.
1-1
3. Verify the scanner operation by scanning a bar code from the Sample
Symbols in the back of this manual.
For additional USB programming and technical information, refer to the Honey-
well “USB Application Note,” available at www.honeywellaidc.com.
Connecting with Keyboard Wedge

A scanner can be connected between the keyboard and PC as a “keyboard
wedge,” plugged into the serial port or connected to a portable data terminal.
The following is an example of a keyboard wedge connection:
1. Turn off power and disconnect the keyboard cables from the back of the ter-
minal/computer.
2. Connect the appropriate interface cable to the scanner and to the terminal/
computer.
only if
power
supply is
included
3. Turn the terminal/computer power back on. The scanner beeps.

Symbols in the back of this manual. The scanner beeps once.
The unit defaults to an IBM PC AT and compatibles keyboard wedge interface
with a USA keyboard. A carriage return (CR) suffix is added to bar code data.
1-2
Connecting with RS-232 Serial Port
1. Turn off power to the terminal/computer.
2. Connect the appropriate interface cable to the scanner.
only if
power
supply is
included
3. Plug the serial connector into the serial port on your computer. Tighten the
two screws to secure the connector to the port.
4. Once the scanner has been completely connected, power up the computer.
5. This interface programs 38,400 baud, 8 data bits, no parity, and 1 stop bit.
Connecting with RS485

A scanner can be connected for an IBM POS terminal interface.
1-3
1. Connect the appropriate interface cable to the device, then to the computer.
2. Turn the terminal/computer power back on. The scanner beeps.

Symbols in the back of this manual. The scanner beeps once.
4. For further RS485 settings, refer to RS485 on page 2-3.
Reading Techniques
The scanner has a bright red aiming beam that corresponds to its horizontal
field of view. The aiming beam should be centered horizontally over the bar
code; it will not read if the aiming beam is in any other direction.
Good Technique Bad Technique
Bad Technique
1-4
The best focus point for reading most code densities is about 5 inches (12.7 cm)
from the unit. To read a single bar code or multiple bar codes (on a page or on
an object), hold the scanner at an appropriate distance from the target, pull the
trigger, and center the aiming beam on the bar code.
Menu Bar Code Security Settings

Honeywell scanners are programmed by scanning menu bar codes or by send-
ing serial commands to the scanner. If you want to restrict the ability to scan
menu codes, you can use the Menu Bar Code Security settings. Please contact
the nearest technical support office (seeTechnical Assistance on page 12-1) for
further information.
Resetting the Standard Product Defaults

If you aren’t sure what programming options are in your scanner, or you’ve
changed some options and want the factory settings restored, scan the Stan-
dard Product Default Settings bar code below.
Standard Product Default

Settings
The Menu Commands starting on page 9-5 lists the factory default settings for
each of the commands (indicated by an asterisk (*) on the programming pages).
1-5
1-6
2 Programming the Interface
Introduction
This chapter describes how to program your system for the desired interface.
Programming the Interface - Plug and Play

Plug and Play bar codes provide instant scanner set up for commonly used
interfaces.
Note: After you scan one of the codes, power cycle the host terminal to have
the interface in effect.
Keyboard Wedge
If you want your system programmed for an IBM PC AT and compatibles key-
board wedge interface with a USA keyboard, scan the bar code below. Key-
board wedge is the default interface.
Note: The following bar code also programs a carriage return (CR) suffix.
IBM PC AT and Compatibles with CR Suffix
Laptop Direct Connect

For most laptops, scanning the Laptop Direct Connect bar code allows opera-
tion of the scanner in parallel with the integral keyboard. The following Laptop
Direct Connect bar code selects terminal ID 03, programs a carriage return
(CR) suffix and turns on Emulate External Keyboard (page 2-10).
Laptop Direct Connect

with CR suffix
2-1
IBM PS2 Keyboard
The following bar code programs you scanner for an IBM PS2 keyboard wedge
interface with a USA keyboard.
Note: The following bar code also programs a carriage return (CR) suffix.
IBM PS2 with CR Suffix
RS232 Serial Port

The RS232 Interface bar code is used when connecting to the serial port of a
PC or terminal. The following RS232 Interface bar code also programs a car-
riage return (CR) and a line feed (LF) suffix, baud rate, and data format as indi-
cated below.
Option Setting
Baud Rate 38,400 bps
Data Format 8 data bits, no parity bit, 1 stop bit
RS232 Interface
2-2
RS485
Scan one of the following “Plug and Play” codes to program the scanner for an
IBM POS terminal interface.
Note: After scanning one of these codes, you must power cycle the cash
register.
IBM Port 5B Interface
IBM Port 9B
HHBCR-1 Interface
IBM Port 17 Interface
IBM Port 9B
HHBCR-2 Interface
Each bar code above also programs the following suffixes for each symbology:
Symbology Suffix Symbology Suffix

EAN 8 0C Code 39 00 0A 0B
EAN 13 16 Interleaved 2 of 5 00 0D 0B
UPC A 0D Code 128 * 00 0A 0B
UPC E 0A Code 128 ** 00 18 0B
* Suffixes programmed for Code 128 with IBM 4683 Port 5B, IBM 4683 Port 9B
HHBCR-1, and IBM 4683 Port 17 Interfaces
**Suffixes programmed for Code 128 with IBM 4683 Port 9 HHBCR-2 Interface
2-3
OPOS Mode
The following bar code configures your scanner for OPOS (OLE for Retail Point
of Sale) by modifying the following OPOS-related settings:
Option Setting
Interface RS232
Baud Rate 38400
RS232 Flow Control, No Timeout
Handshaking XON/XOFF Off
ACK/NAK Off
Data Bits, Stop 8 Data, 1 Stop, Parity None
Bits, and Parity
Prefix/Suffix Clear All Prefixes and Suffixes
Add Code ID and AIM ID Prefix
Add CR Suffix
Intercharacter Off
Delay
Symbologies Enable UPC-A with check digit and number system
Enable UPC-E0 with check digit
Enable EAN/JAN-8 with check digit
Enable EAN/JAN-13 with check digit
Enable Code 128
Enable Code 39
Enable OPOS with automatic disable off
OPOS Mode
2-4
USB IBM SurePos
Scan the following “Plug and Play” codes to program the scanner for an IBM
SurePos (USB handheld scanner) interface.
Note: After scanning the code below, you must power cycle the cash register.
USB IBM SurePos

(USB Handheld Scanner)
Interface
USB IBM SurePos

(USB Tabletop Scanner)
Interface
The bar code above also programs the following suffixes for each symbology:
Symbology Suffix Symbology Suffix

EAN 8 0C Code 39 00 0A 0B
EAN 13 16 Interleaved 2 of 5 00 0D 0B
UPC A 0D Code 128 00 18 0B
UPC E 0A Code 39 00 0A 0B
USB PC or Macintosh Keyboard

Scan one of the following codes to program the scanner for USB PC Keyboard
or USB Macintosh Keyboard. Scanning these codes also adds a CR and LF.
USB Keyboard (PC)
USB Keyboard (Mac)
2-5
USB HID
Scan the following code to program the scanner for USB HID bar code scan-
ners.
USB HID Bar Code Scanner
USB Serial Commands

USB Serial Emulation
Scan the following code to program the scanner to emulate a regular RS232-
based COM Port. If you are using a Microsoft® Windows® PC, you will need to
download a driver from the Honeywell website (www.honeywellaidc.com). The
driver will use the next available COM Port number. Apple® Macintosh comput-
ers recognize the scanner as a USB CDC class device and automatically uses
a class driver.
Scanning this code also adds a CR and LF.
USB Serial Emulation
Note: No extra configuration (e.g., baud rate) is necessary.
CTS/RTS Emulation
CTS/RTS Emulation On
* CTS/RTS Emulation Off
2-6
ACK/NAK Mode
ACK/NAK Mode On
* ACK/NAK Mode Off
2-7
Keyboard Country Layout
Scan the appropriate country code below to program the keyboard layout for
your country. As a general rule, the following characters are supported, but
need special care for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
* United States
Belgium
Denmark
Finland
France
Germany/Austria
Great Britain
2-8
Italy
Norway
Spain
Switzerland
Please refer to Honeywell website (www.honeywellaidc.com) for complete key-

board country support information and applicable interfaces. If you need to pro-
gram a keyboard for a country other than one listed above, scan the Program
Keyboard Country bar code below, then scan the numeric bar code(s) for the
appropriate country from the inside back cover, then the Save bar code.
Program Keyboard Country
Keyboard Wedge Modifiers

Keyboard Style
This programs keyboard styles, such as Caps Lock and Shift Lock. Default =
Regular.
2-9
Regular is used when you normally have the Caps Lock key off.
* Regular
Caps Lock is used when you normally have the Caps Lock key on.
Caps Lock
Shift Lock is used when you normally have the Shift Lock key on (not common
to U.S. keyboards).
Shift Lock
Automatic Caps Lock is used if you change the Caps Lock key on and off.
The software tracks and reflects if you have Caps Lock on or off (AT and PS/2
only). This selection can only be used with systems that have an LED, which
notes the Caps Lock status.
Automatic Caps Lock
Autocaps via NumLock bar code should be scanned in countries (e.g., Ger-
many, France) where the Caps Lock key cannot be used to toggle Caps Lock.
The NumLock option works similarly to the regular Auotcaps, but uses the Num-
Lock key to retrieve the current state of the Caps Lock.
Autocaps via NumLock
2 - 10
Emulate External Keyboard should be scanned if you do not have an external
keyboard (IBM AT or equivalent).
Emulate External Keyboard
Note: After scanning the Emulate External Keyboard bar code, you must power
cycle your computer.
Keyboard Modifiers
This modifies special keyboard features, such as CTRL+ ASCII codes.
Control + ASCII Mode On: The scanner sends key combinations for ASCII
control characters for values 00-1F. Windows is the preferred mode. All key-
board country codes are supported. DOS mode is a legacy mode, and it does
not support all keyboard country codes. New users should use the Windows
mode. Refer to Keyboard Function Relationships, page 7-1 for CTRL+ ASCII
Values. Default = Off
Windows Mode Control + ASCII

Mode On
* Control + ASCII Mode Off
DOS Mode Control + ASCII

Mode On
2 - 11
Numeric Keypad Mode: Sends numeric characters as if entered from a
numeric keypad. Default = Off
Numeric Keypad Mode On
* Numeric Keypad Mode Off
Automatic Direct Connect Mode: This selection can be used if you have an
IBM AT style terminal and the system is dropping characters. Default = Off
Automatic Direct
Connect Mode On
* Automatic Direct Connect

Mode Off
2 - 12
RS232 Modifiers
RS-232 Baud Rate
Baud Rate sends the data from the scanner to the terminal at the specified rate.
The host terminal must be set for the same baud rate as the scanner.
Default = 38,400.
300
600
1200
2400
4800
9600
19200
2 - 13
* 38400
57,600
115,200
RS-232 Word Length: Data Bits, Stop Bits, and Parity

Data Bits sets the word length at 7 or 8 bits of data per character. If an applica-
tion requires only ASCII Hex characters 0 through 7F decimal (text, digits, and
punctuation), select 7 data bits. For applications which require use of the full
ASCII set, select 8 data bits per character. Default = 8.
Stop Bits sets the stop bits at 1 or 2. Default = 1.
2 - 14
Parity provides a means of checking character bit patterns for validity.
Default = None.
7 Data, 1 Stop, Parity Even
7 Data, 1 Stop, Parity None
7 Data, 1 Stop, Parity Odd
7 Data, 2 Stop Parity None
* 8 Data, 1 Stop, Parity None
2 - 15
RS-232 Handshaking
RS232 Handshaking allows control of data transmission from the scanner using
software commands from the host device. When RTS/CTS is turned Off, no
data flow control is used.
RTS/CTS
The scanner asserts RTS when it has data to send, and waits indefinitely for
CTS to be asserted by the host.
Default = RTS/CTS Off.
RTS/CTS On
* RTS/CTS Off
XON/XOFF
Standard ASCII control characters can be used to tell the scanner to start send-
ing data (XON/XOFF On) or to stop sending data (XON/XOFF Off). When the
host sends the XOFF character (DC3, hex 13) to the scanner, data transmission
stops. To resume transmission, the host sends the XON character (DC1, hex
11). Data transmission continues where it left off when XOFF was sent.
Default = XON/XOFF Off.
XON/XOFF On
* XON/OFF Off
ACK/NAK
After transmitting data, the scanner waits for an ACK character (hex 06) or a
NAK character (hex 15) response from the host. If ACK is received, the commu-
nications cycle is completed and the scanner looks for more bar codes. If NAK
is received, the last set of bar code data is retransmitted and the scanner waits
2 - 16
for ACK/NAK again. Turn on the ACK/NAK protocol by scanning the ACK/NAK
On bar code below. To turn off the protocol, scan ACK/NAK Off. Default =
ACK/NAK Off.
ACK/NAK On
* ACK/NAK Off
2 - 17
2 - 18
3 Input/Output Settings
Good Read Indicators

Beeper – Good Read
The beeper may be programmed On or Off in response to a good read. Turning
this option off, only turns off the beeper response to a good read indication. All
error and menu beeps are still audible. Default = On.
* On
Off
Beeper Volume – Good Read

The beeper volume codes modify the volume of the beep the scanner emits on
a good read. Default = High.
Low
Medium
*High
Off
3-1
Beeper Pitch – Good Read
The beeper pitch codes modify the pitch (frequency) of the beep the scanner
emits on a good read. Default = Medium
Low (1600 Hz)
* Medium (2750 Hz)
High (4200 Hz)
Beeper Duration – Good Read

The beeper duration codes modify the length of the beep the scanner emits on
a good read. Default = Normal.
* Normal Beep
Short Beep
3-2
Beeper Pitch – Error
The beeper pitch codes modify the pitch (frequency) of the sound the scanner
emits when there is a bad read or error. Default = 100 Hz.
* Razz (100 Hz)
* Medium (2000 Hz)
High (4200 Hz)
LED – Good Read

The LED indicator can be programmed On or Off in response to a good read.
Default = On.
* On
Off
Number of Beeps – Good Read

The number of beeps of a good read can be programmed from 1 - 9. The same
number of beeps will be applied to the beeper and LED in response to a good
read. For example, if you program this option to have five beeps, there will be
five beeps and five LED flashes in response to a good read. The beeps and
LED flashes are in sync with one another. To change the number of beeps,
3-3
scan the bar code below and then scan a digit (1-9) bar code and the Save bar
code on the Programming Chart inside the back cover of this manual. Default =
One.
Number of Pulses
Good Read Delay

This sets the minimum amount of time before the scanner can read another bar
code. Default = No Delay.
* No Delay
Short Delay (500 ms)
Medium Delay (1000 ms)
Long Delay (1500 ms)
User-Specified Good Read Delay

If you want to set your own length for the good read delay, scan the bar code
below, then set the delay (from 0-30,000 milliseconds) by scanning digits from
the inside back cover, then scanning Save.
User-Specified Good Read Delay
3-4
Trigger Modes
Manual/Serial Trigger
You can activate the scanner either by pressing the trigger, or using a serial trig-
ger command (see Trigger Commands on page 9-4). When in manual trigger
mode, the scanner scans until a bar code is read, or until the trigger is released.
When in serial mode, the scanner scans until a bar code has been read or until
the deactivate command is sent. In serial mode, the scanner can also be set to
turn itself off after a specified time has elapsed (see Read Time-Out, which fol-
lows).
* Manual/Serial Trigger
Read Time-Out
Use this selection to set a time-out (in milliseconds) of the scanner’s trigger
when using serial commands to trigger the scanner. Once the scanner has
timed out, you can activate the scanner either by pressing the trigger or using a
serial trigger command. After scanning the Read Time-Out bar code, set the
time-out duration (from 0-300,000 milliseconds) by scanning digits from the
inside back cover, then scanning Save. Default = 30,000.
Read Time-Out
Automatic Trigger
The scanner scans continuously using internal LEDs to detect bar codes.
Automatic Trigger
3-5
Presentation Mode
Presentation Mode uses ambient light to detect bar codes. The LEDs are off for
ambient conditions until a change occurs in the scanner’s field of view. Then
the LEDS turn on automatically to read the code. If the light level in the room is
not high enough, Presentation Mode may not work properly.
Presentation Mode
Continuous Illumination Mode

If you have several bar codes that are close together, you may wish to have a
continuous aiming beam on in order to properly aim the scanner at one bar
code. Scan the Continuous Illumination On bar code to program the scanner
for this capability. Once you have the aiming beam over the correct bar code,
pull the trigger to read the code. Scan the Continuous Illumination Off bar
code to turn off this feature.
Continuous Illumination
Mode On
* Continuous Illumination
Mode Off
Hands Free Time-Out

The Automatic Trigger and Presentation Modes are referred to as “hands free”
modes. If the scanner’s trigger is pulled when using a hands free mode, the
scanner changes to manual trigger mode. You can set the time the scanner
should remain in manual trigger mode by setting the Hands Free Time-Out.
Once the time-out value is reached, (if there have been no further trigger pulls)
the scanner reverts to the original hands free mode.
3-6
Scan the Hands Free Time-Out bar code, then scan the time-out duration
(from 0-300,000 milliseconds) from the inside back cover, and Save. Default =
5,000 ms.
Hands Free Time-Out
Reread Delay
This sets the time period before the scanner can read the same bar code a sec-
ond time. Setting a reread delay protects against accidental rereads of the
same bar code. Longer delays are effective in minimizing accidental rereads at
POS (point of sale). Use shorter delays in applications where repetitive bar
code scanning is required. Default = Medium.
Reread Delay only works when in automatic trigger mode or presentation mode
(see page 3-5).
Short (500 ms)
* Medium (750 ms)
Long (1000 ms)
Extra Long (2000 ms)
3-7
User-Specified Reread Delay
If you want to set your own length for the reread delay, scan the bar code below,
then set the delay (from 0-30,000 milliseconds) by scanning digits from the
inside back cover, then scanning Save.
User-Specified Reread Delay
Centering
Use Centering to narrow the scanner’s field of view to make sure the scanner
reads only those bar codes intended by the user. For instance, if multiple codes
are placed closely together, centering will insure that only the desired codes are
read.
If a bar code is not touched by a predefined window, it will not be decoded or
output by the scanner. If centering is turned on by scanning Centering On, the
scanner only reads codes that pass through the centering window you specify
using the Left of Centering Window, or Right of Centering Window bar
codes.
In the example below, the red line is the full scanner field of view and the white
boxed area is the centering window. The centering window has been set to
20% left and 30% right, as shown in the legend at the bottom. Since Bar Code
1 passes through the centering window, it will be read. Bar Code 2 does not
pass through the centering window, so it will not be read.
Bar Code 1 Bar Code 2
0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
Scan Centering On, then scan one of the following bar codes to change the left
or right of the centering window. Then scan the percent you want to shift the
centering window using digits on the inside back cover of this manual. Scan
Save. Default Centering = 40% for Left, 60% for Right.
3-8
Centering On
* Centering Off
Left of Centering Window
Right of Centering Window
3-9
Output Sequence Overview
Require Output Sequence
When turned off, the bar code data will be output to the host as the scanner
decodes it. When turned on, all output data must conform to an edited
sequence or the scanner will not transmit the output data to the host device.
Note: This selection is unavailable when the Multiple Symbols Selection is
turned on.
Output Sequence Editor
This programming selection allows you to program the scanner to output data
(when scanning more than one symbol) in whatever order your application
requires, regardless of the order in which the bar codes are scanned. Reading
the Default Sequence symbol programs the scanner to the Universal values,
shown below. These are the defaults. Be certain you want to delete or clear all
formats before you read the Default Sequence symbol.
Note: To make Output Sequence Editor selections, you’ll need to know the
code I.D., code length, and character match(es) your application
requires. Use the Alphanumeric symbols (inside back cover) to read
these options.
Note: You must hold the trigger while reading each bar code in a sequence.
To Add an Output Sequence

1. Scan the Enter Sequence symbol (see Require Output Sequence, page 3-
11).
2. Code I.D.
On the Symbology Chart on page A-1, find the symbology to which you want
to apply the output sequence format. Locate the Hex value for that symbol-
ogy and scan the 2 digit hex value from the Programming Chart (inside back
cover).
3. Length
Specify what length (up to 9999 characters) of data output will be acceptable
for this symbology. Scan the four digit data length from the Programming
Chart. (Note: 50 characters is entered as 0050. 9999 is a universal num-
ber, indicating all lengths.) When calculating the length, you must count any
programmed prefixes, suffixes, or formatted characters as part of the length
(unless using 9999).
4. Character Match Sequences
On the ASCII Conversion Chart (Code Page 1252), page A-2, find the Hex
value that represents the character(s) you want to match. Use the Program-
ming Chart to read the alphanumeric combination that represents the ASCII
characters. (99 is the Universal number, indicating all characters.)
5. End Output Sequence Editor
Scan F F to enter an Output Sequence for an additional symbology, or Save
to save your entries.
3 - 10
Other Programming Selections
•Discard
This exits without saving any Output Sequence changes.
Enter Sequence
Default Sequence

When an output sequence is Required, all output data must conform to an
edited sequence or the scanner will not transmit the output data to the host
device. When it’s On/Not Required, the scanner will attempt to get the output
data to conform to an edited sequence, but if it cannot, the scanner transmits all
output data to the host device as is.
When the output sequence is Off, the bar code data is output to the host as the
scanner decodes it.
turned on.
Required
On/Not Required
* Off
3 - 11
Output Sequence Example
In this example, you are scanning Code 93, Code 128, and Code 39 barcodes,
but you want the image scanner to output Code 39 1st, Code 128 2nd, and
Code 93 3rd, as shown below.
Note: Code 93 must be enabled to use this example.
A - Code 39
B - Code 128
C - Code 93
You would set up the sequence editor with the following command line:
SEQBLK62999941FF6A999942FF69999943FF
The breakdown of the command line is shown below:
SEQBLKsequence editor start command
62 code identifier for Code 39
9999 code length that must match for Code 39, 9999 = all lengths
41 start character match for Code 39, 41h = “A”
FF termination string for first code
6A code identifier for Code 128
42 start character match for Code 128, 42h = “B”
FF termination string for second code
43 start character match for Code 93, 43h = “C”
FF termination string for third code
To program the previous example using specific lengths, you would have to
count any programmed prefixes, suffixes, or formatted characters as part of the
length. If you use the example on page 3-12, but assume a <CR> suffix and
specific code lengths, you would use the following command line:
SEQBLK62001241FF6A001342FF69001243FF
3 - 12
The breakdown of the command line is shown below:
SEQBLK sequence editor start command
0012 A - Code 39 sample length (11) plus CR suffix (1) = 12
41 start character match for Code 39, 41h = “A”
FF termination string for first code
6A code identifier for Code 128
0013 B - Code 128 sample length (12) plus CR suffix (1) = 13
42 start character match for Code 128, 42h = “B”
FF termination string for second code
0012 C - Code 93 sample length (11) plus CR suffix (1) = 12
43 start character match for Code 93, 43h = “C”
FF termination string for third code
Enter Sequence
Default Sequence

When an output sequence is Required, all output data must conform to an
edited sequence or the image scanner will not transmit the output data to the
host device. When it’s On/Not Required, the image scanner will attempt to get
the output data to conform to an edited sequence, but if it cannot, the image
scanner transmits all output data to the host device as is.
3 - 13
When the output sequence is Off, the barcode data is output to the host as the
image scanner decodes it.
turned on.
Required
On/Not Required
*Off
Multiple Symbols
When this programming selection is turned On, it allows you to read multiple
symbols with a single pull of the scanner’s trigger. If you press and hold the trig-
ger, aiming the scanner at a series of symbols, it reads unique symbols once,
beeping (if turned on) for each read. The scanner attempts to find and decode
new symbols as long as the trigger is pulled. When this programming selection
is turned Off, the scanner will only read the symbol closest to the aiming beam.
On
* Off
3 - 14
No Read
With No Read turned On, the scanner sends an “NR” to the host if you pull and
release the trigger without reading a code (e.g., bad bar code). If No Read is
turned Off, the “NR” will not be sent to the host.
On
* Off
If you want a different notation than “NR,” for example, “Error,” or “Bad Code,”
you can edit the output message using the Data Formatter (page 5-8). The hex
code for the No Read symbol is 9C.
Video Reverse
Video Reverse is used to allow the scanner to read bar codes that are inverted.
The “Off” bar code below is an example of this type of bar code.
Note: If additional menuing is required, Video Reverse must be disabled to read
the menu bar codes and then re-enabled after menuing is completed.
On
VIDREV0REV.
* Off
3 - 15
3 - 16
4 Data Editing
Prefix/Suffix Overview
When a bar code is scanned, additional information is sent to the host computer
along with the bar code data. This group of bar code data and additional,
user-defined data is called a “message string.” The selections in this section
are used to build the user-defined data into the message string.
Prefix and Suffix characters are data characters that can be sent before and
after scanned data. You can specify if they should be sent with all symbologies,
or only with specific symbologies. The following illustration shows the break-
down of a message string:
Prefix Scanned Data Suffix

1-11 variable length 1-11
alpha numeric alpha numeric
characters characters
Points to Keep In Mind

• It is not necessary to build a message string. The selections in this chapter
are only used if you wish to alter the default settings. Default prefix = None.
Default suffix = None.
• A prefix or suffix may be added or cleared from one symbology or all
symbologies.
• You can add any prefix or suffix from the ASCII Conversion Chart (Code Page
1252) on page A-2, plus Code I.D. and AIM I.D.
• You can string together several entries for several symbologies at one time.
• Enter prefixes and suffixes in the order in which you want them to appear on
the output.
• When setting up for specific symbologies (as opposed to all symbologies), the
specific symbology ID value counts as an added prefix or suffix character.
• The maximum size of a prefix or suffix configuration is 200 characters, which
includes header information
To Add a Prefix or Suffix

Step 1. Scan the Add Prefix or Add Suffix symbol (page 4-3).
Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in
Appendix A) for the symbology to which you want to apply the prefix or
suffix. For example, for Code 128, Code ID is “j” and Hex ID is “6A”.
4-1
Step 3. Scan the 2 hex digits from the Programming Chart inside the back
cover of this manual or scan 9, 9 for all symbologies.
Step 4. Determine the hex value from the ASCII Conversion Chart (Code Page
1252) on page A-2, for the prefix or suffix you wish to enter.
Step 5. Scan the 2 digit hex value from the Programming Chart inside the back
cover of this manual.
Step 6. Repeat Steps 4 and 5 for every prefix or suffix character.
Step 7. To add the Code I.D., scan 5, C, 8, 0.
To add AIM I.D., scan 5, C, 8, 1.
To add a backslash (\), scan 5, C, 5, C.
Note: To add a backslash (\) as in Step 7, you must scan 5C twice – once to
create the leading backslash and then to create the backslash itself.
Step 8. Scan Save to exit and save, or scan Discard to exit without saving.
Repeat Steps 1-6 to add a prefix or suffix for another symbology.
Example: Add a Suffix to a specific symbology

To send a CR (carriage return)Suffix for UPC only:
Step 1. Scan Add Suffix.
Step 2. Determine the 2 digit hex value from the Symbology Chart (included in
the ASCII Conversion Chart (Code Page 1252) on page A-2) for UPC.
Step 3. Scan 6, 3 from the Programming Chart inside the back cover of this
manual.
Step 4. Determine the hex value from the ASCII Conversion Chart (Code Page
1252) on page A-2, for the CR (carriage return).
Step 5. Scan 0, D from the Programming Chart inside the back cover of this
manual.
Step 6. Scan Save, or scan Discard to exit without saving.
To Clear One or All Prefixes or Suffixes

You can clear a single prefix or suffix, or clear all prefixes/suffixes for a symbol-
ogy. When you Clear One Prefix (Suffix), the specific character you select is
deleted from the symbology you want. When you Clear All Prefixes (Suffixes),
all the prefixes or suffixes for a symbology are deleted.
4-2
Step 1. Scan the Clear One Prefix or Clear One Suffix symbol.
Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in
Appendix A) for the symbology from which you want to clear the prefix
or suffix.
Step 3. Scan the 2 digit hex value from the Programming Chart inside the back
cover of this manual or scan 9, 9 for all symbologies.
Your change is automatically saved.
To Add a Carriage Return Suffix to All Symbologies

Scan the following bar code if you wish to add a carriage return suffix to all sym-
bologies at once. This action first clears all current suffixes, then programs a
carriage return suffix for all symbologies.
Add CR Suffix
All Symbologies
Prefix Selections
Add Prefix
Clear One Prefix
Clear All Prefixes
4-3
Suffix Selections
Add Suffix
Clear One Suffix
Clear All Suffixes
Function Code Transmit

When this selection is enabled and function codes are contained within the
scanned data, the scanner transmits the function code to the terminal. Charts
of these function codes are provided in Supported Interface Keys starting on
page 7-3. When the scanner is in keyboard wedge mode, the scan code is con-
verted to a key code before it is transmitted. Default = Enable.
* Enable
Disable
Intercharacter, Interfunction, and Intermessage

Delays
Some terminals drop information (characters) if data comes through too quickly.
Intercharacter, interfunction, and intermessage delays slow the transmission of
data, increasing data integrity.
Each delay is composed of a 5 millisecond step. You can program up to 99
steps (of 5 ms each) for a range of 0-495 ms.
4-4
Intercharacter Delay
An intercharacter delay of up to 495 milliseconds may be placed between the
transmission of each character of scanned data. Scan the Intercharacter
Delay bar code below, then scan the number of milliseconds and the Save bar
code using the Programming Chart inside the back cover of this manual.
1 2 3 4 5
To remove this delay, scan the Intercharacter Delay bar code, then set the
number of steps to 0. Scan the Save bar code using the Programming Chart
inside the back cover of this manual.
Note: Intercharacter delays are not supported in USB serial emulation.
User Specified Intercharacter Delay

An intercharacter delay of up to 495 milliseconds may be placed after the trans-
mission of a particular character of scanned data. Scan the Delay Length bar
code below, then scan the number of milliseconds and the Save bar code using
the Programming Chart inside the back cover of this manual.
Next, scan the Character to Trigger Delay bar code, then the 2-digit hex value
for the ASCII character that will trigger the delay ASCII Conversion Chart (Code
Page 1252) on page A-2.
Delay Length
Character to Trigger Delay
4-5
To remove this delay, scan the Delay Length bar code, and set the number of
steps to 0. Scan the Save bar code using the Programming Chart inside the
back cover of this manual.
Interfunction Delay
An interfunction delay of up to 495 milliseconds may be placed between the
transmission of each segment of the message string. Scan the Interfunction
Delay bar code below, then scan the number of milliseconds and the Save bar
code using the Programming Chart inside the back cover of this manual.
STX 1 HT 2 3 4 5 CR LF
Interfunction Delays
Interfunction Delay
To remove this delay, scan the Interfunction Delay bar code, then set the num-
ber of steps to 0. Scan the Save bar code using the Programming Chart inside
the back cover of this manual.
Intermessage Delay
An intermessage delay of up to 495 milliseconds may be placed between each
scan transmission. Scan the Intermessage Delay bar code below, then scan
the number of milliseconds and the Save bar code using the Programming
Chart inside the back cover of this manual.
1st Scan Transmission 2nd Scan Transmission

Intermessage Delay
Intermessage Delay
To remove this delay, scan the Intermessage Delay bar code, then set the
number of steps to 0. Scan the Save bar code using the Programming Chart
inside the back cover of this manual.
4-6
5 Data Formatting
Data Format Editor Introduction

You may use the Data Format Editor to change the scanner’s output. For exam-
ple, you can use the Data Format Editor to insert characters at certain points in
bar code data as it is scanned. The selections in the following pages are used
only if you wish to alter the output. Default Data Format setting = None.
Normally, when you scan a bar code, it gets outputted automatically; however
when you do a format, you must use a “send” command (see Send Commands
on page 5-4) within the format program to output data.
Multiple formats may be programmed into the scanner. They are stacked in the
order in which they are entered. However, the following list presents the order
in which formats are applied:
1. Specific Term ID, Actual Code ID, Actual Length
2. Specific Term ID, Actual Code ID, Universal Length
3. Specific Term ID, Universal Code ID, Actual Length
4. Specific Term ID, Universal Code ID, Universal Length
5. Universal Term ID, Actual Code ID, Actual Length
6. Universal Term ID, Actual Code ID, Universal Length
7. Universal Term ID, Universal Code ID, Actual Length
8. Universal Term ID, Universal Code ID, Universal Length
The maximum size of a data format configuration is 256 bytes, which includes
header information. No format can contain more than 50 bytes.
If you have changed data format settings, and wish to clear all formats and
return to the factory defaults, scan the Default Data Format code below.
* Default Data Format
To Add a Data Format

Step 1. Scan the Enter Data Format symbol (page 5-8).
Step 2. Select Primary/Alternate Format
Determine if this will be your primary data format or one of 3 alternate
formats. This allows you to save a total of 4 different data formats. To
program your primary format scan 0 using the Programming Chart
inside the back cover of this manual. If you are programming an alter-
5-1
nate format, scan 1, 2, or 3, depending on which alternate format you
are programming.
Step 3. Terminal Type
Refer to the Supported Terminals Chart (page 5-4) and locate the Ter-
minal ID number for your PC. Scan three numeric bar codes on the
inside back cover to program the scanner for your terminal ID (you must
enter 3 digits). For example, scan 0 0 3 for an AT wedge.
Note: The wildcard for all terminal types is 099.
Step 4. Code I.D.
In Appendix A find the symbology to which you want to apply the data
format. Locate the Hex value for that symbology and scan the 2 digit
hex value from the Programming Chart inside the back cover of this
manual.
Step 5. Length
Specify what length (up to 9999 characters) of data will be acceptable
for this symbology. Scan the four digit data length from the Program-
ming Chart inside the back cover of this manual. (Note: 50 characters
is entered as 0050. 9999 is a universal number, indicating all lengths.)
Step 6. Editor Commands
Refer to the Format Editor Commands Chart (page 5-4). Scan the
symbols that represent the command you want to enter. 94 alphanu-
meric characters may be entered for each symbology data format.
Step 7. Scan Save from the Programming Chart inside the back cover of this
manual to save your entries.
Enter Data Format
Save
Discard
5-2
Other Programming Selections
• Clear One Data Format
This deletes one data format for one symbology. If you are clearing the
primary format, scan 0 from the Programming Chart inside the back cover of
this manual. If you are clearing an alternate format, scan 1, 2, or 3, depending
on the alternate format you are clearing. Scan the Terminal Type (refer to the
Supported Terminals Chart on page 5-4), Code I.D. (refer to the Symbology
Chart on page A-1), and the bar code data length for the specific data format
that you want to delete. All other formats remain unaffected.
• Save from the Programming Chart inside the back cover of this manual
This exits, saving any Data Format changes.
• Discard from the Programming Chart inside the back cover of this manual
This exits without saving any Data Format changes.
Clear One Data Format
Clear All Data Formats
Save
Discard
5-3
Terminal ID Table
Terminal
Terminal Model(s)
ID
IBM AT, PS/2 30–286, 50, 55SX, 60, 003
70, 70–061, 70–121, 80
USB SurePOS Handheld 128
Scanner
USB SurePOS Tabletop 129
Scanner
RS232 TTL 000
RS485 IBM Tailgate 4682 051
USB Com Port 130
PC Keyboard 124*
Mac Keyboard 125
HID POS 131
* Factory default setting
Data Format Editor Commands
Send Commands
Send all Characters
F1 Include in the output message all of the characters from the input message,
starting from current cursor position, followed by an insert character. Syn-
tax = F1xx where xx stands for the insert character’s hex value for its ASCII
code. Refer to ASCII Conversion Chart (Code Page 1252) on page A-2 for
decimal, hex and character codes.
F2 Include in the output message a number of characters followed by an insert
character. Start from the current cursor position and continue for “nn” char-
acters or through the last character in the input message, followed by char-
acter “xx.” Syntax = F2nnxx where nn stands for the numeric value (00-99)
for the number of characters, and xx stands for the insert character’s hex
value for its ASCII code.
Refer to ASCII Conversion Chart (Code Page 1252) on page A-2 for deci-
mal, hex and character codes.
Send all characters up to a particular character

F3 Include in the output message all characters from the input message, start-
ing with the character at the current cursor position and continuing to, but
not including, the search character “ss,” followed by an insert character.
The cursor is moved forward to the “ss” character. Syntax = F3ssxx where
ss stands for the search character’s hex value for its ASCII code, and xx
stands for the insert character’s hex value for its ASCII code.
5-4
Refer to ASCII Conversion Chart (Code Page 1252) on page A-2 for deci-
mal, hex and character codes.
Send all but the last characters

E9 Include in the output message all but the last “nn” characters, starting from
the current cursor position. The cursor is moved forward to one position
past the last input message character included. Syntax = E9nn where nn
stands for the numeric value (00-99) for the number of characters that will
not be sent at the end of the message.
Insert a character multiple times

F4 Send “xx” character “nn” times in the output message, leaving the cursor in
the current position. Syntax = F4xxnn where xx stands for the insert char-
acter’s hex value for its ASCII code, and nn is the numeric value (00-99) for
the number of times it should be sent.
Refer to the ASCII Conversion Chart (Code Page 1252) on page A-4 for
Move Commands
Move the cursor forward a number of characters
F5 Move the cursor ahead “nn” characters from current cursor position.
Syntax = F5nn where nn is the numeric value (00-99) for the number of
characters the cursor should be moved ahead.
Move the cursor backward a number of characters

F6 Move the cursor back “nn” characters from current cursor position.
Syntax = F6nn where nn is the numeric value (00-99) for the number of
characters the cursor should be moved back.
Move the cursor to the beginning

F7 Move the cursor to the first character in the input message. Syntax = F7.
Move the cursor to the end

EA Move the cursor to the last character in the input message. Syntax = EA
Search Commands
Search forward for a character
F8 Search the input message forward for “xx” character from the current cursor
position, leaving the cursor pointing to the “xx” character. Syntax = F8xx
where xx stands for the search character’s hex value for its ASCII code.
5-5
Search backward for a character
F9 Search the input message backward for “xx” character from the current cur-
sor position, leaving the cursor pointing to the “xx” character. Syntax =
F9xx where xx stands for the search character’s hex value for its ASCII
code.
Search forward for a non-matching character

E6 Search the input message forward for the first non-“xx” character from the
current cursor position, leaving the cursor pointing to the non-“xx” charac-
ter. Syntax = E6xx where xx stands for the search character’s hex value
for its ASCII code.
Search backward for a non-matching character

E7 Search the input message backward for the first non-“xx” character from the
current cursor position, leaving the cursor pointing to the non-“xx” charac-
ter. Syntax = E7xx where xx stands for the search character’s hex value
for its ASCII code.
Miscellaneous Commands
Suppress characters
FB Suppress all occurrences of up to 15 different characters, starting at the
current cursor position, as the cursor is advanced by other commands.
When the FC command is encountered, the suppress function is termi-
nated. The cursor is not moved by the FB command.
Syntax = FBnnxxyy . .zz where nn is a count of the number of suppressed
characters in the list, and xxyy .. zz is the list of characters to be sup-
pressed.
Stop suppressing characters

FC Disables suppress filter and clear all suppressed characters. Syntax = FC.
Replace characters
E4 Replaces up to 15 characters in the output message, without moving the
cursor. Replacement continues until the E5 command is encountered.
Syntax = E4nnxx1xx2yy1yy2...zz1zz2 where nn is the total count of the num-
ber of characters in the list (characters to be replaced plus replacement
characters); xx1 defines characters to be replaced and xx2 defines replace-
ment characters, continuing through zz1 and zz2.
5-6
Stop replacing characters
E5 Terminates character replacement. Syntax = E5.
Compare characters
FE Compare the character in the current cursor position to the character “xx.”
If characters are equal, move the cursor forward one position. Syntax =
FExx where xx stands for the comparison character’s hex value for its
ASCII code.
Check for a number

EC Check to make sure there is an ASCII number at the current cursor position.
The format is aborted if the character is not numeric.
Check for non-numeric character

ED Check to make sure there is a non-numeric ASCII character at the current
cursor position. The format is aborted if the character is not numeric.
5-7
Data Format Editor
Enter Data Format
* Default Data Format
Clear One Data Format
Clear All Data Formats
Save
Discard
Data Formatter
When Data Formatter is turned off, the bar code data is output to the host as
read (including prefixes and suffixes). Choose one of the following options.
5-8
Default = Data Formatter On.
* Data Formatter On,

but Not Required
Data Formatter Off
When Data Formatter is required, all input data must conform to an edited for-
mat or the scanner does not transmit the input data to the host device.
Data Format On, Format Required
5-9
5 - 10
6 Symbologies
Introduction
This programming section contains the following menu selections. Refer to
Chapter 9 for settings and defaults.
• All Symbologies • GS1 DataBar Expanded

• China Post Code • Interleaved 2 of 5
• Codabar • Label Code
• Codablock F • Matrix 2 of 5
• Code 11 • MSI
• Code 39 • Plessey Code
• Straight 2 of 5 IATA (two-bar
• Code 32 Pharmaceutical (PARAF)
start/stop)
• Straight 2 of 5 Industrial
• Code 49 (three-bar start/stop)
• Code 93 • Telepen
• Code 128 • Trioptic Code
• UPC-A/EAN-13 with Extended • UPC A
Coupon Code
• EAN/JAN 8 • UPC E
• Straight 2 of 5 IATA (two-bar
• GS1 DataBar Omnidirectional
start/stop)
• Straight 2 of 5 Industrial
• GS1 DataBar Limited
(three-bar start/stop)
6-1
All Symbologies
If you want to decode all the symbologies allowable for your scanner, scan the
All Symbologies On code. If on the other hand, you want to decode only a
particular symbology, scan All Symbologies Off followed by the On symbol for
that particular symbology.
All Symbologies On
All Symbologies Off
Message Length
You are able to set the valid reading length of some of the bar code symbologies.
If the data length of the scanned bar code doesn’t match the valid reading length,
the scanner will issue an error beep. You may wish to set the same value for
minimum and maximum length to force the scanner to read fixed length bar code
data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09 Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15 Max. length = 15
For a value other than the minimum and maximum message length defaults,
scan the bar codes included in the explanation of the symbology, then scan the
digit value of the message length and Save bar codes on the Programming Chart
inside the back cover of this manual. The minimum and maximum lengths and
the defaults are included with the respective symbologies.
6-2
Codabar
<Default All Codabar Settings>
Codabar
*On
Off
Codabar Start/Stop Characters

Start/Stop characters identify the leading and trailing ends of the bar code. You
may either transmit, or not transmit Start/Stop characters.
Default = Don’t Transmit.
Transmit
* Don’t Transmit
Codabar Check Character

Codabar check characters are created using different “modulos.” You can pro-
gram the scanner to read only Codabar bar codes with Modulo 16 check char-
acters. Default = No Check Character.
6-3
No Check Character indicates that the scanner reads and transmits bar code
data with or without a check character.
When Check Character is set to Validate and Transmit, the scanner will only
read Codabar bar codes printed with a check character, and will transmit this
character at the end of the scanned data.
When Check Character is set to Validate, but Don’t Transmit, the unit will only
read Codabar bar codes printed with a check character, but will not transmit the
check character with the scanned data.
* No Check Character
Validate Modulo 16, but

Don’t Transmit
Validate Modulo 16 and Transmit
Codabar Concatenation
Codabar supports symbol concatenation. When you enable concatenation, the
scanner looks for a Codabar symbol having a “D” start character, adjacent to a
symbol having a “D” stop character. In this case the two messages are concat-
enated into one with the “D” characters omitted.
Character Start Stop Start Stop
Codabar
A12D D34A
Select Require to prevent the scanner from decoding a single “D” Codabar sym-
bol without its companion. This selection has no effect on Codabar symbols
without Stop/Start D characters.
6-4
On
* Off
Require
Codabar Message Length

Scan the bar codes below to change the message length. Refer to Message
Length on page 6-2 for additional information. Minimum and Maximum
lengths = 2-60. Minimum Default = 4, Maximum Default = 60.
Minimum Message Length
Maximum Message Length
6-5
Code 39
< Default All Code 39 Settings >
Code 39
*On
Off
Code 39 Start/Stop Characters

Start/Stop characters identify the leading and trailing ends of the bar code. You
may either transmit, or not transmit Start/Stop characters. Default = Don’t
Transmit.
Transmit
* Don’t Transmit
Code 39 Check Character

No Check Character indicates that the scanner reads and transmits bar code
data with or without a check character.
When Check Character is set to Validate, but Don’t Transmit, the unit only
reads Code 39 bar codes printed with a check character, but will not transmit
the check character with the scanned data.
6-6
When Check Character is set to Validate and Transmit, the scanner only reads
Code 39 bar codes printed with a check character, and will transmit this charac-
ter at the end of the scanned data. Default = No Check Character.
* No Check Character
Validate, but Don’t Transmit
Validate and Transmit
Code 39 Message Length

Code 39 Append
This function allows the scanner to append the data from several Code 39 bar
codes together before transmitting them to the host computer. When this func-
tion is enabled, the scanner stores those Code 39 bar codes that start with a
space (excluding the start and stop symbols), and does not immediately trans-
mit the data. The scanner stores the data in the order in which the bar codes
6-7
are read, deleting the first space from each. The scanner transmits the
appended data when it reads a Code 39 bar code that starts with a character
other than a space. Default = Off.
On
*Off
Code 32 Pharmaceutical (PARAF)

Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian
pharmacies. This symbology is also known as PARAF. Default = Off.
On
* Off
6-8
Full ASCII
If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar
code symbol will be interpreted as a single character. For example: $V will be
decoded as the ASCII character SYN, and /C will be decoded as the ASCII
character #. Default = Off.
NUL %U DLE $P SP SPACE 0 0 @ %V P P ‘ %W p +P

SOH $A DC1 $Q ! /A 1 1 A A Q Q a +A q +Q
STX $B DC2 $R “ /B 2 2 B B R R b +B r +R
ETX $C DC3 $S # /C 3 3 C C S S c +C s +S
EOT $D DC4 $T $ /D 4 4 D D T T d +D t +T
ENQ $E NAK $U % /E 5 5 E E U U e +E u +U
ACK $F SYN $V & /F 6 6 F F V V f +F v +V
BEL $G ETB $W ‘ /G 7 7 G G W W g +G w +W
BS $H CAN $X ( /H 8 8 H H X X h +H x +X
HT $I EM $Y ) /I 9 9 I I Y Y i +I y +Y
LF $J SUB $Z * /J : /Z J J Z Z j +J z +Z
VT $K ESC %A + /K ; %F K K [ %K k +K { %P
FF $L FS %B , /L < %G L L \ %L l +L | %Q
CR $M GS %C - - = %H M M ] %M m +M } %R
SO $N RS %D . . > %I N N ^ %N n +N ~ %S
SI $O US %E / /O ? %J O O _ %O o +O DEL %T
Character pairs /M and /N decode as a minus sign and period respectively.

Character pairs /P through /Y decode as 0 through 9.
Full ASCII On
* Full ASCII Off
Code 39 Code Page

Code pages define the mapping of character codes to characters. If the data
received does not display with the proper characters, it may be because the bar
code being scanned was created using a code page that is different from the
one the host program is expecting. If this is the case, scan the bar code below,
select the code page with which the bar codes were created from the chart,
6-9
Code Page Mapping of Printed Bar Codes on page A-5, and scan the value and
the Save bar code from the Programming Chart inside the back cover of this
manual. The data characters should then appear properly.
Code 39 Code Page
Interleaved 2 of 5
< Default All Interleaved 2 of 5 Settings >
Interleaved 2 of 5
* On
Off
Check Digit
No Check Digit indicates that the scanner reads and transmits bar code data
with or without a check digit.
When Check Digit is set to Validate, but Don’t Transmit, the unit only reads
Interleaved 2 of 5 bar codes printed with a check digit, but will not transmit the
check digit with the scanned data.
6 - 10
When Check Digit is set to Validate and Transmit, the scanner only reads
Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this digit
at the end of the scanned data. Default = No Check Digit.
* No Check Digit
Validate, but Don’t Transmit
Validate and Transmit
Interleaved 2 of 5 Message Length

6 - 11
Code 93
< Default All Code 93 Settings >
Code 93
* On
Off

Code 93 Code Page

6 - 12
Code 93 Code Page
6 - 13
Straight 2 of 5 Industrial (three-bar start/stop)
<Default All Straight 2 of 5 Settings>
Straight 2 of 5 Industrial
* On
Off
Straight 2 of 5 Industrial Message Length

6 - 14
Straight 2 of 5 IATA (two-bar start/stop)
<Default All Code IATA 2 of 5 Settings>
Straight 2 of 5 IATA
On
Off
Straight 2 of 5 IATA Message Length

6 - 15
Matrix 2 of 5
<Default All Matrix 2 of 5 Settings>
Matrix 2 of 5
On
* Off
Matrix 2 of 5 Message Length

6 - 16
Code 11
<Default All Code 11 Settings>
Code 11
On
* Off
Check Digits Required

This option sets whether 1 or 2 check digits are required with Code 11 bar
codes. Default = Two Check Digits.
One Check Digit
* Two Check Digits
6 - 17
Code 128
Code 128
* On
Off
ISBT 128 Concatenation

In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard
for communicating critical blood information in a uniform manner. The use of
ISBT formats requires a paid license. The ISBT 128 Application Specification
describes 1) the critical data elements for labeling blood products, 2) the current
recommendation to use Code 128 due to its high degree of security and its
6 - 18
space-efficient design, 3) a variation of Code 128 that supports concatenation
of neighboring symbols, and 4) the standard layout for bar codes on a blood
product label. Use the bar codes below to turn concatenation on or off. Default
=Off.
On
* Off

Code 128 Code Page

6 - 19
Code 128 Code Page
Code 128 Function Code Transmit

By default, Code 128 function codes are not transmitted with Code 128 bar
code data. However, if you wish to transmit Code 128 function codes with the
bar code data, scan the Function Codes On bar code, below. Default = Off
* Function Codes Off
Function Codes On
Telepen
<Default All Telepen Settings>
6 - 20
Telepen
On
* Off
Telepen Output
Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1
and decodes them as standard full ASCII (start/stop pattern 1). When Original
Telepen Output is selected, the scanner reads symbols with start/stop pattern 1
and decodes them as compressed numeric with optional full ASCII (start/stop
pattern 2). Default = AIM Telepen Output.
*AIM Telepen Output
Original Telepen Output
6 - 21
Telepen Message Length
6 - 22
UPC A
<Default All UPC A Settings>
UPC A
* On
Off
UPC A Check Digit

This selection allows you to specify whether the check digit should be transmit-
ted at the end of the scanned data or not. Default = On.
* On
Off
6 - 23
UPC A Number System
The numeric system digit of a U.P.C. symbol is normally transmitted at the
beginning of the scanned data, but the unit can be programmed so it will not
transmit it. Default = On.
* On
Off
UPC A Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC A data.
Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
6 - 24
UPC A Addenda Required
When Addenda Required is set to on, the scanner will only read UPC A bar
codes that have addenda. Default = Not Required.
Required
* Not Required
UPC A Addenda Separator

When this feature is on, there is a space between the data from the bar code
and the data from the addenda. When turned off, there is no space.
Default = On.
* On
Off
6 - 25
UPC-A/EAN-13
with Extended Coupon Code
Use the following codes to enable or disable UPC-A and EAN-13 with Extended
Coupon Code. Default = On.
On
* Off
6 - 26
UPC E
<Default All UPC E Settings>
UPC E0 and UPC E1

Most U.P.C. bar codes lead with the 0 number system. For these codes, use the
UPC E0 selection. If you need to read codes that lead with the 1 number sys-
tem, use the UPC E1 selection. Default = On (UPC E0) and Off (UPC E1).
* UPC E0 On
UPC E0 Off
UPC E1 On
* UPC E1 Off
6 - 27
UPC E0 and UPC E1 Expand
UPC E Expand expands the UPC E code to the 12 digit, UPC A format.
Default = Off.
On
* Off
UPC E0 and UPC E1 Addenda Required

When Addenda Required is set to on, the scanner will only read UPC E bar
Required
* Not Required
6 - 28
UPC E0 and UPC E1 Addenda Separator
Default = On.
* On
Off
UPC E0 Check Digit

Check Digit specifies whether the check digit should be transmitted at the end of
the scanned data or not. Default = On.
* On
Off
6 - 29
UPC E0 Number System
The numeric system digit of a U.P.C. symbol is normally transmitted at the
beginning of the scanned data, but the unit can be programmed so it will not
transmit it. Default = On.
* On
Off
UPC E0 Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC E data.
2 Digit Addenda On
5 Digit Addenda On
6 - 30
EAN/JAN 13
<Default All EAN/JAN Settings>
EAN/JAN 13
* On
Off
EAN/JAN 13 Check Digit

* On
Off
6 - 31
EAN/JAN 13 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 13 data.
2 Digit Addenda On
5 Digit Addenda On
EAN/JAN 13 Addenda Required

When Addenda Required is set to on, the scanner will only read EAN/JAN 13
bar codes that have addenda. Default = Not Required.
Required
* Not Required
6 - 32
EAN/JAN 13 Addenda Separator
Default = On.
* On
Off
Note: If you want to enable or disable EAN13 with Extended Coupon Code,
refer to UPC-A/EAN-13 with Extended Coupon Code on page 6-26.
ISBN Translate
This selection causes EAN-13 Bookland symbols to be translated into their
equivalent ISBN number format. Default = Off.
On
* Off
EAN/JAN 8
<Default All EAN/JAN 8 Settings>
6 - 33
EAN/JAN 8
* On
Off
Off
EAN/JAN 8 Check Digit

* On
Off
6 - 34
EAN/JAN 8 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 8 data.
2 Digit Addenda On
5 Digit Addenda On
* 5 Digit Addenda
EAN/JAN 8 Addenda Required

When Addenda Required is set to on, the scanner will only read EAN/JAN 8 bar
Required
* Not Required
6 - 35
EAN/JAN 8 Addenda Separator
Default = On.
* On
Off
MSI
<Default All MSI Settings>
MSI
On
* Off
MSI Check Character

Different types of check characters are used with MSI bar codes. You can
program the scanner to read MSI bar codes with Type 10 check characters.
Default = Validate Type 10, but Don’t Transmit.
6 - 36
When Check Character is set to Validate and Transmit, the scanner will only
read MSI bar codes printed with the specified type check character, and will
transmit this character at the end of the scanned data.
When Check Character is set to Validate, but Don’t Transmit, the unit will only
read MSI bar codes printed with the specified type check character, but will not
transmit the check character with the scanned data.
* Validate Type 10, but Don’t

Transmit
Validate Type 10 and Transmit
MSI Message Length

Plessey Code
<Default All Plessey Code Settings>
6 - 37
Plessey Code
On
* Off
Plessey Message Length

GS1 DataBar Omnidirectional

< Default All GS1 DataBar Omnidirectional Settings >
6 - 38
GS1 DataBar Omnidirectional
* On
Off
GS1 DataBar Limited

< Default All GS1 DataBar Limited Settings >
GS1 DataBar Limited
* On
Off
GS1 DataBar Expanded

< Default All GS1 DataBar Expanded Settings >
6 - 39
GS1 DataBar Expanded
* On
Off
GS1 DataBar Expanded Message Length

China Post Code

<Default All China Post Code Settings>
6 - 40
China Post Code
On
* Off
China Post Message Length

6 - 41
Korea Post Code
<Default All Korea Post Code Settings>
Korea Post Code
On
* Off
Korea Post Message Length

6 - 42
Codablock F
<Default All Codablock F Settings>
Codablock F
On
* Off
Codablock F Message Length

6 - 43
Code 49
Code 49
On
* Off

6 - 44
Trioptic Code
Trioptic Code is used for labeling magnetic storage media.
On
Off
GS1 Emulation
The scanner can automatically format the output from any GS1 data carrier to
emulate what would be encoded in an equivalent GS1-128 or GS1 DataBar
symbol. GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8,
ITF-14, GS1-128, and GS1-128 DataBar and GS1Composites. If GS1-128
Emulation is selected, the AIM Symbology Identifier will be reported as “]C1”. If
GS1 DataBar Emulation is selected, the AIM Symbology Identifier will be
reported as “]e0.” Any application that accepts GS1 data can be simplified
since it only needs to recognize one data carrier type. Default = GS1 Emulation
Off.
GS1 Data Bar Emulation
GS1-128 Emulation
* GS1 Emulation Off
6 - 45
Label Code
The standard Label Code is used in library situations. Default = Off.
On
* Off
6 - 46
7 Interface Keys
Keyboard Function Relationships

The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII
“CTRL”+ relationships apply to all terminals that can be used with the scanner.
Refer to page 2-12 enable Control + ASCII mode.
Function Code HEX/ASCII Value Full ASCII “CTRL” +

NUL 00 2
SOH 01 A
STX 02 B
ETX 03 C
EOT 04 D
ENQ 05 E
ACK 06 F
BEL 07 G
BS 08 H
HT 09 I
LF 0A J
VT 0B K
FF 0C L
CR 0D M
SO 0E N
SI 0F O
DLE 10 P
DC1 11 Q
DC2 12 R
DC3 13 S
DC4 14 T
NAK 15 U
SYN 16 V
ETB 17 W
CAN 18 X
EM 19 Y
SUB 1A Z
ESC 1B [
FS 1C \
GS 1D ]
RS 1E 6
US 1F -
7-1
The last five characters in the Full ASCII “CTRL”+ column ( [ \ ] 6 - ), apply to
US only. The following chart indicates the equivalents of these five characters
for different countries.
Country Codes
United States [ \ ] 6 -
Belgium [ < ] 6 -
Scandinavia 8 < 9 6 -
France ^ 8 $ 6 =
Germany Ã + 6 -
Italy \ + 6 -
Switzerland < .. 6 -
United Kingdom [ ¢ ] 6 -
Denmark 8 \ 9 6 -
Norway 8 \ 9 6 -
Spain [ \ ] 6 -
7-2
Supported Interface Keys
IBM AT/XT and
PS/2 Compatibles,
WYSE PC/AT
ASCII HEX Supported Keys
NUL 00 Reserved
SOH 01 Enter (KP)
STX 02 Cap Lock
ETX 03 ALT make
EOT 04 ALT break
ENQ 05 CTRL make
ACK 06 CTRL break
BEL 07 CR/Enter
BS 08 Reserved
HT 09 Tab
LF 0A Reserved
VT 0B Tab
FF 0C Delete
CR 0D CR/Enter
SO 0E Insert
SI 0F Escape
DLE 10 F11
DC1 11 Home
DC2 12 Print
DC3 13 Back Space
DC4 14 Back Tab
NAK 15 F12
SYN 16 F1
ETB 17 F2
CAN 18 F3
EM 19 F4
SUB 1A F5
ESC 1B F6
FS 1C F7
GS 1D F8
RS 1E F9
US 1F F10
* IBM 3191/92, 3471/72, 3196/97, 3476/77,
Telex (all models)
7-3
Supported Interface Keys
Apple Mac/iMac
ASCII HEX Supported Keys
NUL 00 Reserved
SOH 01 Enter/Numpad Enter
STX 02 CAPS
ETX 03 ALT make
EOT 04 ALT break
ENQ 05 CNTRL make
ACK 06 CNTRL break
BEL 07 RETURN
BS 08 APPLE make
HT 09 TAB
LF 0A APPLE break
VT 0B TAB
FF 0C Del
CR 0D RETURN
SO 0E Ins Help
SI 0F ESC
DLE 10 F11
DC1 11 Home
DC2 12 Prnt Scrn
DC3 13 BACKSPACE
DC4 14 LSHIFT TAB
NAK 15 F12
SYN 16 F1
ETB 17 F2
CAN 18 F3
EM 19 F4
SUB 1A F5
ESC 1B F6
FS 1C F7
GS 1D F8
RS 1E F9
US 1F F10
DEL 7F BACKSPACE
7-4
8 Utilities
To Add a Test Code I.D. Prefix to All Symbologies

This selection allows you to turn on transmission of a Code I.D. before the
decoded symbology. (See the Symbology Chart, included in the "Appendix
A" on page A-1) for the single character code that identifies each symbology.)
This action first clears all current prefixes, then programs a Code I.D. prefix for
all symbologies. This is a temporary setting that will be removed when the unit
is power cycled.
Add Code I.D. Prefix to

All Symbologies (Temporary)
Show Software Revision

Scan the bar code below to output the current software revision, unit serial num-
ber, and other product information.
Show Revision
Show Data Format

Scan the bar code below to show current data format settings.
DFMBK3?.
Data Format Settings
8-1
changed some options and want the standard product default settings restored,
scan the Standard Product Default Settings bar code below.
Standard Product Default Settings
The Menu Commands starting on page 9-5 lists the standard product default
settings for each of the commands (indicated by an asterisk (*) on the program-
ming pages).
EZConfig Introduction
EZConfig provides a wide range of PC-based programming functions that can
be performed on a scanner connected to your PC's COM port. EZConfig allows
you to download upgrades to the scanner's firmware, change programmed
parameters, and create and print programming bar codes. Using EZConfig, you
can even save/open the programming parameters for a scanner. This saved file
can be e-mailed or, if required, you can create a single bar code that contains
all the customized programming parameters and mail or fax that bar code to
any location. Users in other locations can scan the bar code to load in the cus-
tomized programming.
To communicate with a scanner, EZConfig requires that the PC have at least
one available serial communication port, or a serial port emulation using a
physical USB port. If you are using the serial port and RS232 cable, an external
power supply is required. When using a USB serial port emulation, only a USB
cable is required.
EZConfig Operations
The EZConfig software performs the following operations:
Scan Data
Scan Data allows you to scan bar codes and display the bar code data
in a window. Scan Data lets you send serial commands to the scanner
and receive scanner response that can be seen in the Scan Data win-
dow. The data displayed in the Scan Data window can either be saved
in a file or printed.
Configure
Configure displays the programming and configuration data of the
scanner. The scanner's programming and configuration data is
grouped into different categories. Each category is displayed as a tree
item under the "Configure" tree node in the application explorer. When
one of these tree nodes is clicked, the right-hand side is loaded with
8-2
the parameters' form belonging to that particular category. The "Con-
figure" tree option has all the programming and configuration parame-
ters specified for a scanner. You can set or modify these parameters
as required. You can later write the modified settings to the scanner,
or save them to a dcf file.
Installing EZConfig from the Web

Note: EZConfig requires .NET software. If .NET is not installed on your PC,
you will be prompted to install it during the EZConfig installation.
1. Access the Honeywell web site at www.honeywellaidc.com

2. Click on the Resources tab. Select Product Downloads-Software.
3. Click on the dropdown for Select Product Number. Click on Xenon.
4. Click on the listing for EZConfig.
5. When prompted, select Save File, and save the files to the
c:\windows\temp directory.
6. Once you have finished downloading the file, exit the web site.
7. Using Explorer, go to the c:\windows\temp file.
8. Double click on the Setup.exe file. Follow the screen prompts to install
the EZConfig program.
9. If you’ve selected the defaults during installation, you can click on Start
Menu-All Programs-Honeywell-EZConfig.
8-3
8-4
9
Serial Programming Commands
The serial programming commands can be used in place of the programming

bar codes. Both the serial commands and the programming bar codes will pro-
gram the scanner. For complete descriptions and examples of each serial pro-
gramming command, refer to the corresponding programming bar code in this
manual.
The device must be set to an RS-232 interface (see page 2-2). The following
commands can be sent via a PC com port using terminal emulation software.
Conventions
The following conventions are used for menu and query command descriptions:
parameterA label representing the actual value you should send as part of a
command.
[option] An optional part of a command.
{Data} Alternatives in a command.
bold Names of menus, menu commands, buttons, dialog boxes, and
windows that appear on the screen.
Menu Command Syntax

Menu commands have the following syntax (spaces have been used for clarity
only):
Prefix Tag SubTag {Data} [, SubTag {Data}] [; Tag SubTag {Data}] […] Storage
Prefix Three ASCII characters: SYN M CR (ASCII 22,77,13).
Tag A 3 character case-insensitive field that identifies the desired menu
command group. For example, all RS-232 configuration settings
are identified with a Tag of 232.
SubTag A 3 character case-insensitive field that identifies the desired menu
command within the tag group. For example, the SubTag for the
RS-232 baud rate is BAD.
Data The new value for a menu setting, identified by the Tag and Sub-
Tag.
Storage A single character that specifies the storage table to which the
command is applied. An exclamation point (!) performs the com-
mand’s operation on the device’s volatile menu configuration table.
A period (.) performs the command’s operation on the device’s
non-volatile menu configuration table. Use the non-volatile table
only for semi-permanent changes you want saved through a power
cycle.
9-1
Query Commands
Several special characters can be used to query the device about its settings.
^ What is the default value for the setting(s).
? What is the device’s current value for the setting(s).

* What is the range of possible values for the setting(s). (The de-
vice’s response uses a dash (-) to indicate a continuous range of
values. A pipe (|) separates items in a list of non-continuous val-
ues.)
Tag Field Usage
When a query is used in place of a Tag field, the query applies to the entire set
of commands available for the particular storage table indicated by the Storage
field of the command. In this case, the SubTag and Data fields should not be
used because they are ignored by the device.
SubTag Field Usage
When a query is used in place of a SubTag field, the query applies only to the
subset of commands available that match the Tag field. In this case, the Data
field should not be used because it is ignored by the device.
Data Field Usage
When a query is used in place of the Data field, the query applies only to the
specific command identified by the Tag and SubTag fields.
Concatenation of Multiple Commands

Multiple commands can be issued within one Prefix/Storage sequence. Only
the Tag, SubTag, and Data fields must be repeated for each command in the
sequence. If additional commands are to be applied to the same Tag, then the
new command sequence is separated with a comma (,) and only the SubTag
and Data fields of the additional command are issued. If the additional com-
mand requires a different Tag field, the command is separated from previous
commands by a semicolon (;).
Responses
The device responds to serial commands with one of three responses:
ACK Indicates a good command which has been processed.
ENQ Indicates an invalid Tag or SubTag command.
NAK Indicates the command was good, but the Data field entry was out of
the allowable range for this Tag and SubTag combination, e.g., an entry
for a minimum message length of 100 when the field will only accept 2
characters.
When responding, the device echoes back the command sequence with the
status character inserted directly before each of the punctuation marks (the
period, exclamation point, comma, or semicolon) in the command.
9-2
Examples of Query Commands
In the following examples, a bracketed notation [ ] depicts a non-displayable
response.
Example: Example #1:What is the range of possible values for Codabar
Coding Enable?
Enter: cbrena*.
Response: CBRENA0-1[ACK]
This response indicates that Codabar Coding Enable (CBRENA) has a range of
values from 0 to 1 (off and on).
Example: Example #2: What is the default value for Codabar Coding Enable?
Enter: cbrena^.
Response: CBRENA1[ACK]
This response indicates that the default setting for Codabar Coding Enable
(CBRENA) is 1, or on.
Example: Example #3: What is the device’s current setting for Codabar
Coding Enable?
Enter: cbrena?.
Response: CBRENA1[ACK]
This response indicates that the device’s Codabar Coding Enable (CBRENA) is
set to 1, or on.
Example: Example #4: What are the device’s settings for all Codabar
selections?
Enter: cbr?.
Response: CBRENA1[ACK],
SSX0[ACK],
CK20[ACK],
CCT1[ACK],
MIN2[ACK],
MAX60[ACK],
DFT[ACK].
This response indicates that the device’s Codabar Coding Enable (CBRENA) is
set to 1, or on;
the Start/Stop Character (SSX) is set to 0, or Don’t Transmit;
the Check Character (CK2) is set to 0, or Not Required;
concatenation (CCT) is set to 1, or Enabled;
the Minimum Message Length (MIN) is set to 2 characters;
the Maximum Message Length (MAX) is set to 60 characters;
and the Default setting (DFT) has no value.
9-3
Trigger Commands
You can activate and deactivate the scanner with serial trigger commands.
First, the scanner must be put in Manual/Serial Trigger Mode either by scanning
the Manual/Serial Trigger Mode bar code (page 3-5), or by sending the Manual/
Serial Menu Command (page 9-9). Once the scanner is in serial trigger mode,
the trigger is activated and deactivated by sending the following commands:
Activate:SYN T CR
Deactivate:SYN U CR
The scanner scans until a bar code has been read, until the deactivate com-
mand is sent, or until the serial time-out has been reached (see Read Time-
Out on page 3-5 for a description, and the serial command on page 9-9).

changed some options and want the factory settings restored, scan the Stan-
dard Product Default Settings bar code below.
Standard Product Default Settings
The chart on the following pages lists the factory default settings for each of the
menu commands (indicated by an asterisk (*) on the programming pages).
9-4
Menu Commands
Serial
Setting Command
Selection Page
* Indicates default # Indicates a
numeric entry
Factory Default Set- Default DEFALT
tings
Terminal Interfaces
Plug and Play Codes Keyboard Wedge: IBM PAP_AT 2-1
PC AT and Compati-
bles with CR suffix
IBM PS2 Keyboard PAPPS2 2-2
RS232 Serial Port PAP232 2-2
Plug and Play Codes: IBM Port 5B Interface PAPP5B 2-3
RS485 IBM Port 9B HHBCR-1 PAP9B1 2-3
Interface
IBM Port 17 Interface PAPP17 2-3
IBM Port 9B HHBCR-2 PAP9B2 2-3
Interface
Plug and Play Codes: USB IBM SurePos PAPSPH 2-5
IBM SurePos Handheld
USB IBM SurePos PAPSPT 2-5
Tabletop
Plug and Play Codes: USB Keyboard (PC) PAP124 2-5
USB USB Keyboard (Mac) PAP125 2-5
USB HID PAP131 2-6
USB Serial Com- USB Serial Emulation PAP130 2-6
mands CTS/RTS Emulation USBCTS1 2-6
On
*CTS/RTS Emulation USBCTS0 2-6
Off
ACK/NAK Mode On USBACK1 2-7
*ACK/NAK Mode Off USBACK0 2-7
9-5
Serial
Setting Command
Selection Page
numeric entry
Program Keyboard *USA KBDCTY0 2-8
Country Belgium KBDCTY1 2-8
Denmark KBDCTY8 2-8
Finland KBDCTY2 2-8
France KBDCTY3 2-8
Germany/Austria KBDCTY4 2-8
Great Britain KBDCTY7 2-8
Italy KBDCTY5 2-9
Norway KBDCTY9 2-9
Spain KBDCTY10 2-9
Switzerland KBDCTY6 2-9
Keyboard Style *Regular KBDSTY0 2-10
Caps Lock KBDSTY1 2-10
Shift Lock KBDSTY2 2-10
Automatic Caps Lock KBDSTY6 2-10
Autocaps via Num- KBDSTY7 2-10
Lock
Emulate External KBDSTY5 2-11
Keyboard
Keyboard Modifiers Windows Mode Con- KBDCAS2 2-11
trol + ASCII
*Control + ASCII Off KBDCAS0 2-11
DOS Mode Control + KBDCAS1 2-11
ASCII Mode On
*Numeric Keypad Off KBDNPS0 2-12
Numeric Keypad On KBDNPS1 2-12
*Auto Direct Conn. Off KBDADC0 2-12
Auto Direct Conn. On KBDADC1 2-12
Serial Port Connection RS-232 PAP232 2-2
9-6
Serial
Setting Command
Selection Page
numeric entry
Baud Rate 300 BPS 232BAD0 2-13
600 BPS 232BAD1 2-13
1200 BPS 232BAD2 2-13
2400 BPS 232BAD3 2-13
4800 BPS 232BAD4 2-13
9600 BPS 232BAD5 2-13
19200 BPS 232BAD6 2-13
*38400 BPS 232BAD7 2-14
57600 BPS 232BAD8 2-14
115200 BPS 232BAD9 2-14
Word Length: Data 7 Data, 1 Stop, Parity 232WRD3 2-15
Bits, Stop Bits, and Even
Parity 7 Data, 1 Stop, Parity 232WRD0 2-15
None
7 Data, 1 Stop, Parity 232WRD6 2-15
Odd
Even
None
Odd
Even
*8 Data, 1 Stop, Parity 232WRD2 2-15
None
Odd
9-7
Serial
Setting Command
Selection Page
numeric entry
RS-232 Handshaking *RTS/CTS Off 232CTS0 2-16
RTS/CTS On 232CTS1 2-16
*XON/XOFF Off 232XON0 2-16
XON/XOFF On 232XON1 2-16
*ACK/NAK Off 232ACK0 2-17
ACK/NAK On 232ACK1 2-17
Output Selections
Beeper - Good Read Off BEPBEP0 3-1
*On BEPBEP1 3-1
Beeper Volume - Good Off BEPLVL0 3-1
Read Low BEPLVL1 3-1
Medium BEPLVL2 3-1
*High BEPLVL3 3-1
Beeper Pitch - Good Low (1600 Hz) BEPFQ11600 3-2
Read (Frequency) *Medium (2750 Hz) BEPFQ12750 3-2
High (4200 Hz) BEPFQ14200 3-2
Beeper Duration - *Normal Beep BEPBIP0 3-2
Good Read Short Beep BEPBIP1 3-2
Beeper Pitch - Error *Razz (100 Hz) BEPFQ2100 3-3
*Medium (2000 Hz) BEPFQ22000 3-3
High (4200 Hz) BEPFQ24200 3-3
LED - Good Read Off BEPLED0 3-3
*On BEPLED1 3-3
Number of Beeps - *1 BEPRPT1 3-4
Good Read Range 1 - 9 BEPRPT# 3-4
Good Read Delay *No Delay DLYGRD0 3-4
Short Delay (500 ms) DLYGRD500 3-4
Medium Delay (1000 DLYGRD1000 3-4
ms)
Long Delay (1500 ms) DLYGRD1500 3-4
9-8
Serial
Setting Command
Selection Page
numeric entry
User-Specified Good Range 0 - 30,000 ms DLYGRD##### 3-4
Read Delay
Trigger Mode *Manual/Serial Trigger TRGMOD0 3-5
Read Time-Out (0 - TRGSTO#### 3-5
300,000 ms) *30,000
Automatic Trigger TRGMOD1 3-5
Presentation Mode TRGMOD3 3-6
Continuous Illumina- ILLAON1 3-6
tion On
*Continuous Illumina- ILLAON0 3-6
tion Off
Hands Free Time-Out TRG- 3-7
(0-300,000 seconds) PTO######
*5000
Reread Delay Short (500 ms) DLYRRD500 3-7
*Medium (750 ms) DLYRRD750 3-7
Long (1000 ms) DLYRRD1000 3-7
Extra Long (2000 ms) DLYRRD3000 3-7
User-Specified Reread Range 0 - 30,000 ms DLYRRD##### 3-8
Delay
Centering Centering On DECWIN1 3-9
*Centering Off DECWIN0 3-9
Left of Centering Win- DECLFT### 3-9
dow *40
Right of Centering DECRGT### 3-9
Window *60
Output Sequence Edi- Enter Sequence SEQBLK 3-11
tor Default Sequence SEQDFT 3-11
Require Output Required SEQ_EN2 3-11
Sequence On/Not Required SEQ_EN1 3-11
*Off SEQ_EN0 3-11
Multiple Symbols On SHOTGN1 3-15
*Off SHOTGN0 3-15
9-9
Serial
Setting Command
Selection Page
numeric entry
No Read On SHWNRD1 3-15
*Off SHWNRD0 3-15
Video Reverse On VIDREV1 3-14
*Off VIDREV0 3-14
Prefix/Suffix Selections
Add CR Suffix to All Symbologies VSUFCR 4-3
Prefix Add Prefix PREBK2## 4-3
Clear One Prefix PRECL2 4-3
Clear All Prefixes PRECA2 4-3
Suffix Add Suffix SUFBK2## 4-4
Clear One Suffix SUFCL2 4-4
Clear All Suffixes SUFCA2 4-4
Function Code Trans- *Enable RMVFNC0 4-4
mit Disable RMVFNC1 4-4
Intercharacter Delay DLYCHR## 4-5
User Specified Inter- Delay Length DLYCRX## 4-5
character Delay Character to Trigger DLY_XX### 4-5
Delay
Interfunction Delay DLYFNC## 4-6
Intermessage Delay DLYMSG## 4-6
Data Formatter Selections
Data Format Editor *Default Data Format DFMDF3 5-8
(None)
Enter Data Format DFMBK3## 5-8
Clear One Data For- DFMCL3 5-8
mat
Clear All Data Formats DFMCA3 5-8
Data Formatter Off DFM_EN0 5-9
*On, but Not Required DFM_EN1 5-9
On, Required DFM_EN2 5-9
Symbologies
9 - 10
Serial
Setting Command
Selection Page
numeric entry
All Symbologies All Symbologies Off ALLENA0 6-2
All Symbologies On ALLENA1 6-2
Codabar Default All Codabar CBRDFT 6-3
Settings
Codabar Off CBRENA0 6-3
*On CBRENA1 6-3
Codabar Start/Stop *Don’t Transmit CBRSSX0 6-3
Char. Transmit CBRSSX1 6-3
Codabar Check Char. *No Check Char. CBRCK20 6-4
Validate, But Don’t CBRCK21 6-4
Transmit
Validate, and Transmit CBRCK22 6-4
Codabar Concatena- *Off CBRCCT0 6-5
tion On CBRCCT1 6-5
Require CBRCCT2 6-5
Codabar Message Minimum (2 - 60) *4 CBRMIN## 6-5
Length Maximum (2 - 60) *60 CBRMAX## 6-5
Code 39 Default All Code 39 C39DFT 6-6
Settings
Code 39 Off C39ENA0 6-6
*On C39ENA1 6-6
Code 39 Start/Stop *Don’t Transmit C39SSX0 6-6
Char. Transmit C39SSX1 6-6
Code 39 Check Char. *No Check Char. C39CK20 6-7
Validate, But Don’t C39CK21 6-7
Transmit
Validate, C39CK22 6-7
and Transmit
Code 39 Message Minimum (0 - 48) *0 C39MIN## 6-7
Length Maximum (0 - 48) *48 C39MAX## 6-7
Code 39 Append *Off C39APP0 6-8
On C39APP1 6-8
9 - 11
Serial
Setting Command
Selection Page
numeric entry
Code 32 Pharmaceuti- *Off C39B320 6-8
cal (PARAF) On C39B321 6-8
Code 39 Full ASCII *Off C39ASC0 6-9
On C39ASC1 6-9
Interleaved 2 of 5 Default All Interleaved I25DFT 6-10
2 of 5 Settings
Interleaved 2 of 5 Off I25ENA0 6-10
*On I25ENA1 6-10
Interleaved 2 of 5 *No Check Char. I25CK20 6-11
Check Digit Validate, But Don’t I25CK21 6-11
Transmit
Validate, and Transmit I25CK22 6-11
Interleaved 2 of 5 Mes- Minimum (2 - 80) *4 I25MIN## 6-11
sage Length Maximum (2 - 80) *80 I25MAX## 6-11
Settings
Code 93 Off C93ENA0 6-12
*On C93ENA1 6-12
Straight 2 of 5 Indus- Default All Straight 2 of R25DFT 6-14
trial 5
Settings
Straight 2 of 5 Indus- Off R25ENA0 6-14
trial *On R25ENA1 6-14
Straight 2 of 5 Indus- Minimum (1 - 48) *4 R25MIN## 6-14
trial Message Length Maximum (1 - 48) *48 R25MAX## 6-14
Straight 2 of 5 IATA Default All Straight 2 of A25DFT 6-15
5 IATA
Settings
Straight 2 of 5 IATA *Off A25ENA0 6-15
On A25ENA1 6-15
9 - 12
Serial
Setting Command
Selection Page
numeric entry
Straight 2 of 5 IATA Minimum (1 - 48) *4 A25MIN## 6-15
Message Length Maximum (1 - 48) *48 A25MAX## 6-15
Matrix 2 of 5 Default All Matrix 2 of X25DFT 6-16
5
Settings
Matrix 2 of 5 *Off X25ENA0 6-16
On X25ENA1 6-16
Matrix 2 of 5 Message Minimum (1 - 80) *4 X25MIN## 6-16
Length Maximum (1 - 80) *80 X25MAX## 6-16
Settings
Code 11 *Off C11ENA0 6-17
On C11ENA1 6-17
Code 11 Check Digits 1 Check Digit C11CK20 6-17
Required *2 Check Digits C11CK21 6-17
Code 128 Default All Code 128 128DFT 6-18
Settings
Code 128 Off 128ENA0 6-19
*On 128ENA1 6-18
ISBT Concatenation On ISBENA1 6-19
*Off ISBENA0 6-19
Code 128 Message Minimum (0 - 80) *0 128MIN## 6-19
Length Maximum (0 - 80) *80 128MAX## 6-19
Code 128 Code Page Code 128 Code Page 128DCP 6-20
Code 128 Function *Off 128FNX0 6-20
Code Transmit On 128FNX1 6-20
Telepen Default All Telepen TELDFT 6-21
Settings
Telepen *Off TELENA0 6-21
On TELENA1 6-21
9 - 13
Serial
Setting Command
Selection Page
numeric entry
Telepen Output *AIM Telepen Output TELOLD0 6-21
Original Telepen Out- TELOLD1 6-21
put
Telepen Message Minimum (1 - 60) *1 TELMIN## 6-22
Length Maximum (1 - 60) *60 TELMAX## 6-22
UPC A Default All UPADFT 6-23
UPC A Settings
UPC A Off UPAENA0 6-23
*On UPAENA1 6-23
UPC A Check Digit Off UPACKX0 6-23
*On UPACKX1 6-23
UPC A Number Sys- Off UPANSX0 6-24
tem *On UPANSX1 6-24
UPC A 2 Digit *Off UPAAD20 6-24
Addenda On UPAAD21 6-24
UPC A 5 Digit *Off UPAAD50 6-24
Addenda On UPAAD51 6-24
UPC A Addenda *Not Required UPAARQ0 6-25
Required Required UPAARQ1 6-25
UPC A Addenda Off UPAADS0 6-25
Separator *On UPAADS1 6-25
UPC-A/EAN-13 with *Off CPNENA0 6-26
Extended Coupon On CPNENA1 6-26
Code
UPC E Default All UPC E UPEDFT 6-27
Settings
UPC E0 Off UPEEN00 6-27
*On UPEEN01 6-27
UPC E1 *Off UPEEN10 6-27
On UPEEN11 6-27
UPC E Expand *Off UPEEXP0 6-28
On UPEEXP1 6-28
9 - 14
Serial
Setting Command
Selection Page
numeric entry
UPC E Check Digit Off UPECKX0 6-29
*On UPECKX1 6-29
UPC E Number Sys- Off UPENSX0 6-30
tem *On UPENSX1 6-30
UPC E 2 Digit *Off UPEAD20 6-30
Addenda On UPEAD21 6-30
UPC E 5 Digit *Off UPEAD50 6-30
Addenda On UPEAD51 6-30
UPC E Addenda *Not Required UPEARQ0 6-28
Required Required UPEARQ1 6-28
UPC E Addenda Off UPEADS0 6-29
Separator *On UPEADS1 6-29
EAN/JAN 13 Default All EAN/ E13DFT 6-31
JAN 13 Settings
EAN/JAN 13 Off E13ENA0 6-31
*On E13ENA1 6-31
EAN/JAN 13 Check Off E13CKX0 6-31
Digit *On E13CKX1 6-31
EAN/JAN 13 2 Digit *Off E13AD20 6-32
Addenda On E13AD21 6-32
EAN/JAN 13 5 Digit *Off E13AD50 6-32
Addenda On E13AD51 6-32
EAN/JAN 13 Addenda *Not Required E13ARQ0 6-32
Required Required E13ARQ1 6-32
EAN/JAN 13 Addenda Off E13ADS0 6-33
Separator *On E13ADS1 6-33
ISBN Translate *Off E13ISB0 6-33
On E13ISB1 6-33
EAN/JAN 8 Default All EAN/ EA8DFT 6-34
JAN 8 Settings
9 - 15
Serial
Setting Command
Selection Page
numeric entry
EAN/JAN 8 Off EA8ENA0 6-34
*On EA8ENA1 6-34
EAN/JAN 8 Check Off EA8CKX0 6-34
Digit *On EA8CKX1 6-34
EAN/JAN 8 2 Digit *Off EA8AD20 6-35
Addenda On EA8AD21 6-35
EAN/JAN 8 5 Digit *Off EA8AD50 6-35
Addenda On EA8AD51 6-35
EAN/JAN 8 Addenda *Not Required EA8ARQ0 6-28
Required Required EA8ARQ1 6-28
EAN/JAN 8 Addenda Off EA8ADS0 6-36
Separator *On EA8ADS1 6-36
MSI Default All MSI Set- MSIDFT 6-36
tings
MSI *Off MSIENA0 6-36
On MSIENA1 6-36
MSI Check Character *Validate Type 10, but MSICHK0 6-37
Don’t Transmit
Validate Type 10 and MSICHK1 6-37
Transmit
MSI Message Length Minimum (4 - 48) *4 MSIMIN## 6-37
Maximum (4 - 48) *48 MSIMAX## 6-37
Plessey Code Default All Plessey PLSDFT 6-38
Settings
Plessey Code *Off PLSENA0 6-38
On PLSENA1 6-38
Plessey Message Minimum (4 - 48) *4 PLSMIN## 6-38
Length Maximum (4 - 48) *48 PLSMAX## 6-38
GS1 DataBar Omnidi- Default All RSSDFT 6-39
rectional GS1 DataBar Omnidi-
rectional Settings
9 - 16
Serial
Setting Command
Selection Page
numeric entry
GS1 DataBar Omnidi- Off RSSENA0 6-39
rectional *On RSSENA1 6-39
GS1 DataBar Limited Default All GS1 Data- RSLDFT 6-39
Bar
Limited Settings
GS1 DataBar Limited Off RSLENA0 6-39
*On RSLENA1 6-39
GS1 DataBar Default All GS1 Data- RSEDFT 6-40
Expanded Bar
Expanded Settings
GS1 DataBar Off RSEENA0 6-40
Expanded *On RSEENA1 6-40
GS1 DataBar Minimum (4 - 74) *4 RSEMIN## 6-40
Expanded Msg. Maximum (4 - 74) *74 RSEMAX## 6-40
Length
China Post Code Default All China Post CPCDFT 6-41
Code Settings
China Post Code *Off CPCENA0 6-41
On CPCENA1 6-41
China Post Code Msg. Minimum (2 - 80) *4 CPCMIN## 6-41
Length Maximum (2 - 80) *80 CPCMAX## 6-41
Korea Post Code Default All Korea Post CPCDFT 6-42
Code Settings
Korea Post Code *Off CPCENA0 6-42
On CPCENA1 6-42
Korea Post Code Msg. Minimum (2 - 80) *4 CPCMIN## 6-42
Length Maximum (2 - 80) *80 CPCMAX## 6-42
Codablock F Default All Codablock CBFDFT 6-43
F Settings
Codablock F *Off CBFENA0 6-43
On CBFENA1 6-43
9 - 17
Serial
Setting Command
Selection Page
numeric entry
Codablock F Msg. Minimum (1 - 2048) *1 CBFMIN#### 6-43
Length Maximum (1 - 2048) CBFMAX#### 6-43
*2048
Settings
Code 49 * Off C49ENA0 6-44
On C49ENA1 6-44
Code 49 Minimum (1 - 81) *1 C49MIN## 6-44
Maximum (1 - 81) *81 C49MAX## 6-44
GS1 Emulation EANEMU2 6-45
GS1 Emulation GS1-128 Emulation EANEMU1 6-45
*GS1 Emulation Off EANEMU0 6-45
Label Code *Off LBLENA0 6-46
On LBLENA1 6-46
9 - 18
10
Product Specifications
Hyperion 1300g Product Specifications

Parameter Specification
Mechanical
Height 5.9 inches (15 cm)
Length 4.4 inches (11.2 cm)
Width 3.1 inches (7.9 cm)
Weight 5.6 ounces (160 g)
Electrical
LED source 630 nm visible red LED
Input Voltage 4.5-5.5VDC at imager
Operating Power 200mA @ 5V
Standby Power 125mA @5V
Environmental
Operating Temperature 32° F to +122° F (0° C to +50° C)
Storage Temperature -40° F to +140° F (-40° C to +60° C)
Humidity 0 to 95% non-condensing
Operational after 50 drops from 5 feet
Drop
(1.5 m) to concrete
Environmental Sealing IP41
Light Levels 70,000 lux
ESD 15 kV to any external surface
Scan Performance
Scan Pattern Single Line
Motion Tolerance 20 inches (51 cm) per second
Scan Rate Up to 270 scans per second
Print Contrast 20%
Pitch, Skew ±65
Reads standard 1D and GS1 DataBar
Decode Capabilities
symbologies
Use only a Listed Limited Power Source (LPS) or
Optional External Power Supply
Class 2 type power supply with output rated 5 to
Requirements
5.2Vdc, 1A
10 - 1
10 - 2
10 Pin RJ41 Modular Plug
connects to the scanner handle
1 Cord shield
Keyboard Wedge
2 Tied to supply power

3 Supply ground
4 Terminal data
5 Terminal clock
6 Keyboard clock
Standard Cable Pinouts
7 Supply power input (Refer to tables on page 10-1)

8 Keyboard data
9
10
10 Pin RJ41 Modular Plug
connects to the scanner handle
Serial Output
1 Cord shield
2 Tied to supply ground
3 Supply ground
4 Transmit data
5 Receive clock
6 Clear to send data
7 Supply power input (Refer to tables on page 10-1)

8 Request to send data
9
10
10 - 3
10 - 4
USB
1 Cord shield
2
3 Supply ground
4
5
6
7 Supply power input
8
connects to the scanner handle 9 Data +
10 Pin Modular Plug 10 Data -
11
Maintenance
Repairs
Repairs and/or upgrades are not to be performed on this product. These ser-
vices are to be performed only by an authorized service center. Please see
Customer Support on page 12-1 for further information.
Maintenance
Your device provides reliable and efficient operation with a minimum of care.
Although specific maintenance is not required, the following periodic checks
ensure dependable scanner operation:
Cleaning the Device

Reading performance may degrade if the scanner’s window is not clean. If the
window is visibly dirty, or if the scanner isn’t operating well, clean the window
with a soft cloth or lens tissue dampened with water (or a mild soapy water solu-
tion). If a soapy water solution is used, rinse with a clean lens tissue dampened
with water only.
The scanner’s housing may also be cleaned the same way.
! Caution:
Do not submerge the scanner in water. Do not use
abrasive wipes or tissues on the scanner’s window –
abrasive wipes may scratch the window.
Never use solvents (e.g., acetone, benzene, ether, or

phenol-based agents) on the housing or window –
solvents may damage the finish or the window.
Inspecting Cords and Connectors

Inspect the scanner’s interface cable and connector for wear or other signs of
damage. A badly worn cable or damaged connector may interfere with scanner
operation. Contact your Honeywell distributor for information about cable
replacement. Cable replacement instructions are on page 11-2.
11 - 1
Replacing the Interface Cable
The standard interface cable is attached to the scanner with an 10-pin modular
connector. When properly seated, the connector is held in the scanner’s handle
by a flexible retention tab. The interface cable is designed to be field replace-
able.
• Order replacement cables from Honeywell or from an authorized distributor.
• When ordering a replacement cable, specify the cable part number of the
original interface cable.
Replacing the Interface Cable:

1. Turn the power to the host system
OFF.
2. Disconnect the scanner’s cable from

the terminal or computer.
3. Locate the small hole on the side of
the scanner’s handle. This is the
cable release.
4. Straighten one end of a paper clip.
5. Insert the end of the paper clip into the
small hole and press in. This
depresses the retention tab, releasing
the connector. Pull the connector out
while maintaining pressure on the
paper clip, then remove the paper clip.
6. Replace with the new cable. Cable
Insert the connector into the opening Release
and press firmly. The connector is
keyed to go in only one way, and will click into place.
Troubleshooting
The scanner automatically performs self-tests whenever you turn it on. If your
scanner is not functioning properly, review the following Troubleshooting Guide
to try to isolate the problem.
Is the power on? Is the aiming beam line on?
If the aiming beam line isn’t illuminated, check that:
• The cable is connected properly.
• The host system power is on (if external power isn’t used).
• The trigger works.
11 - 2
Is the scanner having trouble reading your symbols?
If the scanner isn’t reading symbols well, check that the symbols:
• Aren’t smeared, rough, scratched, or exhibiting voids.
• Aren’t coated with frost or water droplets on the surface.
• Are enabled in the scanner or in the decoder to which the scanner connects.
Is the bar code displayed but not entered?

The bar code is displayed on the host device correctly, but you still have to press
a key to enter it (the Enter/Return key or the Tab key, for example).
You need to program a suffix. Programming a suffix enables the scanner to out-
put the bar code data plus the key you need (such as “CR”) to enter the data
into your application. Refer to Prefix/Suffix Overview on page 4-1 for further
information.
Does the scanner read the bar code incorrectly?

If the scanner reads a bar code, but the data is not displayed correctly on the
host screen:
• The scanner may not be programmed for the appropriate terminal interface.
For example, you scan “12345” and the host displays “@es%.”
Reprogram the scanner with the correct Plug and Play or Terminal selection
bar code. See Chapter 1 and Chapter 2.
• The scanner may not be programmed to output your bar code data properly.
For example, you scan “12345” and the host displays “A12345B.”
Reprogram the scanner with the proper symbology selections. See Chapter
6.
The scanner won’t read your bar code at all.

1. Scan the sample bar codes in the back of this manual. If the scanner reads
the sample bar codes, check that your bar code is readable.
Verify that your bar code symbology is enabled (see Chapter 6).
2. If the scanner still can’t read the sample bar codes, scan All Symbologies on
page 6-2.
If you aren’t sure what programming options have been set in the scanner, or if
you want the factory default settings restored, scan Resetting the Standard
Product Defaults on page 9-4.
11 - 3
11 - 4
12
Customer Support
Technical Assistance
If you need assistance installing or troubleshooting your device, please call your
distributor or the nearest technical support office:
North America/Canada
Telephone: (800) 782-4263
E-mail: [email protected]
Latin America
Telephone: (803) 835-8000
Telephone: (800) 782-4263
Brazil
Telephone: +55 (11) 5185-8222
Fax: +55 (11) 5185-8225
Mexico
Telephone: 01-800-HONEYWELL (01-800-466-3993)
Europe, Middle East, and Africa
Telephone: +31 (0) 40 7999 393
Fax: +31 (0) 40 2425 672
Hong Kong
Telephone: +852-29536436
Fax: +852-2511-3557
Singapore
Telephone: +65-6842-7155
Fax: +65-6842-7166
China
Telephone: +86 800 828 2803
Fax: +86-512-6762-2560
Japan
Telephone: +81-3-3839-8511
Fax: +81-3-3839-8519
12 - 1
Online Technical Assistance
You can also access technical assistance online at www.honeywellaidc.com.
Product Service and Repair

Honeywell International Inc. provides service for all its products through service
centers throughout the world. To obtain warranty or non-warranty service,
contact the appropriate location below to obtain a Return Material Authorization
number (RMA #) before returning the product.
North America
Telephone: (800) 782-4263
Latin America
Telephone: (803) 835-8000
Telephone: (800) 782-4263
Fax: (239) 263-9689
Brazil
Telephone: +55 (11) 5185-8222
Fax: +55 (11) 5185-8225
Mexico
Telephone: 01-800-HONEYWELL (01-800-466-3993)
Fax: +52 (55) 5531-3672
Europe, Middle East, and Africa
Telephone: +31 (0) 40 2901 633
Fax: +31 (0) 40 2901 631
Hong Kong
Telephone: +852-29536436
Fax: +852-2511-3557
Singapore
Telephone: +65-6842-7155
Fax: +65-6842-7166
China
Telephone: +86 800 828 2803
Fax: +86-512-6762-2560
12 - 2
Japan
Telephone: +81-3-3839-8511
Fax: +81-3-3839-8519
Online Product Service and Repair Assistance

You can also access product service and repair assistance online at
www.honeywellaidc.com.
Limited Warranty
Honeywell International Inc. ("HII") warrants its products and optional accesso-
ries to be free from defects in materials and workmanship and to conform to
HII’s published specifications applicable to the products purchased at the time
of shipment. This warranty does not cover any HII product which is (i) improp-
erly installed or used; (ii) damaged by accident or negligence, including failure
to follow the proper maintenance, service, and cleaning schedule; or (iii) dam-
aged as a result of (A) modification or alteration by the purchaser or other party,
(B) excessive voltage or current supplied to or drawn from the interface connec-
tions, (C) static electricity or electro-static discharge, (D) operation under condi-
tions beyond the specified operating parameters, or (E) repair or service of the
product by anyone other than HII or its authorized representatives.
This warranty shall extend from the time of shipment for the duration published
by HII for the product at the time of purchase ("Warranty Period"). Any defective
product must be returned (at purchaser’s expense) during the Warranty Period
to HII factory or authorized service center for inspection. No product will be
accepted by HII without a Return Materials Authorization, which may be
obtained by contacting HII. In the event that the product is returned to HII or its
authorized service center within the Warranty Period and HII determines to its
satisfaction that the product is defective due to defects in materials or workman-
ship, HII, at its sole option, will either repair or replace the product without
charge, except for return shipping to HII.
EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW, THE
FOREGOING WARRANTY IS IN LIEU OF ALL OTHER COVENANTS OR
WARRANTIES, EITHER EXPRESSED OR IMPLIED, ORAL OR WRITTEN,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MER-
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR NON-
INFRINGEMENT.
HII’S RESPONSIBILITY AND PURCHASER’S EXCLUSIVE REMEDY UNDER
THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE
DEFECTIVE PRODUCT WITH NEW OR REFURBISHED PARTS. IN NO
12 - 3
EVENT SHALL HII BE LIABLE FOR INDIRECT, INCIDENTAL, OR CONSE-
QUENTIAL DAMAGES, AND, IN NO EVENT, SHALL ANY LIABILITY OF HII
ARISING IN CONNECTION WITH ANY PRODUCT SOLD HEREUNDER
(WHETHER SUCH LIABILITY ARISES FROM A CLAIM BASED ON CON-
TRACT, WARRANTY, TORT, OR OTHERWISE) EXCEED THE ACTUAL
AMOUNT PAID TO HII FOR THE PRODUCT. THESE LIMITATIONS ON LIA-
BILITY SHALL REMAIN IN FULL FORCE AND EFFECT EVEN WHEN HII MAY
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH INJURIES, LOSSES,
OR DAMAGES. SOME STATES, PROVINCES, OR COUNTRIES DO NOT
ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY
NOT APPLY TO YOU.
All provisions of this Limited Warranty are separate and severable, which
means that if any provision is held invalid and unenforceable, such determina-
tion shall not affect the validity of enforceability of the other provisions hereof.
Use of any peripherals not provided by the manufacturer may result in damage
not covered by this warranty. This includes but is not limited to: cables, power
supplies, cradles, and docking stations. HII extends these warranties only to the
first end-users of the products. These warranties are non-transferable.
The duration of the limited warranty for the Hyperion 1300g is five (5) years.
12 - 4
A
Appendix A
Symbology Chart
Possible AIM
Code ID
Symbology AIM ID ID Modifiers
(hex)
( m)
All Symbologies (0x99)
China Post ]X0 Q (0x51)
Codabar ]Fm 0-1 a (0x61)
Codablock F ]Om 0, 1, 4, 5, 6 q (0x71)
Code 11 ]H3 h (0x68)
Code 128 ]Cm 0, 1, 2, 4 j (0x6A)
Code 32 Pharmaceutical (PARAF) ]X0 < (0x3C)
Code 39 (supports Full ASCII mode) ]Am 0, 1, 3, 4, 5, 7 b (0x62)
Code 49 ]Tm 0, 1, 2, 4 l (0x6C)
0-9, A-Z,
Code 93 and 93i ]Gm a-m
i (0x69)
EAN-13 (including Bookland EAN) ]E0 d (0x64)

EAN-13 with Add-On ]E3 d (0x64)
EAN-13 with Extended Coupon Code ]E3 d (0x64)
EAN-8 ]E4 D (0x44)
EAN-8 with Add-On ]E3 D (0x44)
GS1 DataBar ]em 0 y (0x79)
GS1-128 ]C1 I (0x49)
Interleaved 2 of 5 ]Im 0, 1, 3 e (0x65)
Matrix 2 of 5 ]X0 m (0x6D)
MSI ]Mm 0 g (0x67)
Plessey Code ]P0 n (0x6E)
Straight 2 of 5 IATA ]Rm 0, 1, 3 f (0x66)
Straight 2 of 5 Industrial ]S0 f (0x66)
UPC-A ]E0 c (0x63)
UPC-A with Add-On ]E3 c (0x63)
UPC-A with Extended Coupon Code ]E3 c (0x63)
UPC-E ]E0 E (0x45)
A-1
Possible AIM
Code ID
Symbology AIM ID ID Modifiers
(hex)
( m)
UPC-E with Add-On ]E3 E (0x45)
UPC-E1 (obsolete) ]X0 E (0x45)
Note: “m” represents the AIM modifier character. Refer to International

Technical Specification, Symbology Identifiers, for AIM modifier character
details.
Prefix/Suffix entries for specific symbologies override the universal (All
Symbologies, 99) entry.
ASCII Conversion Chart (Code Page 1252)

Note: This table applies to U.S. style keyboards. Certain characters may differ
depending on your Country Code/PC regional settings.
Non-Printable Characters
DEC HEX Character (Code) DEC HEX Character (Code)
0 0 NULL 16 10 DATA LINK ESCAPE (DLE)
1 1 START OF HEADING 17 11 DEVICE CONTROL 1 (DC1)
(SOH)
2 2 START OF TEXT (STX) 18 12 DEVICE CONTROL 2 (DC2)
3 3 END OF TEXT (ETX) 19 13 DEVICE CONTROL 3 (DC3)
4 4 END OF TRANSMISSION 20 14 DEVICE CONTROL 4 (DC4)
(EOT)
5 5 END OF QUERY (ENQ) 21 15 NEGATIVE ACKNOWLEDGE-
MENT (NAK)
6 6 ACKNOWLEDGE (ACK) 22 16 SYNCHRONIZE (SYN)
7 7 BEEP (BEL) 23 17 END OF TRANSMISSION
BLOCK (ETB)
8 8 BACKSPACE (BS) 24 18 CANCEL (CAN)
9 9 HORIZONTAL TAB (HT) 25 19 END OF MEDIUM (EM)
10 A LINE FEED (LF) 26 1A SUBSTITUTE (SUB)
11 B VERTICAL TAB (VT) 27 1B ESCAPE (ESC)
12 C FF (FORM FEED) 28 1C FILE SEPARATOR (FS)
RIGHT ARROW
13 D CR (CARRIAGE RETURN) 29 1D GROUP SEPARATOR (GS)
LEFT ARROW
14 E SO (SHIFT OUT) 30 1E RECORD SEPARATOR (RS)
UP ARROW
A-2
15 F SI (SHIFT IN) 31 1F UNIT SEPARATOR (US)
DOWN ARROW
Printable Characters
DEC HEX Character DEC HEX Character DEC HEX Character
32 20 <SPACE> 64 40 @ 96 60 `
33 21 ! 65 41 A 97 61 a
34 22 " 66 42 B 98 62 b
35 23 # 67 43 C 99 63 c
36 24 $ 68 44 D 100 64 d
37 25 % 69 45 E 101 65 e
38 26 & 70 46 F 102 66 f
39 27 ' 71 47 G 103 67 g
40 28 ( 72 48 H 104 68 h
41 29 ) 73 49 I 105 69 i
42 2A * 74 4A J 106 6A j
43 2B + 75 4B K 107 6B k
44 2C , 76 4C L 108 6C l
45 2D - 77 4D M 109 6D m
46 2E . 78 4E N 110 6E n
47 2F / 79 4F O 111 6F o
48 30 0 80 50 P 112 70 p
49 31 1 81 51 Q 113 71 q
50 32 2 82 52 R 114 72 r
51 33 3 83 53 S 115 73 s
52 34 4 84 54 T 116 74 t
53 35 5 85 55 U 117 75 u
54 36 6 86 56 V 118 76 v
55 37 7 87 57 W 119 77 w
56 38 8 88 58 X 120 78 x
57 39 9 89 59 Y 121 79 y
58 3A : 90 5A Z 122 7A z
59 3B ; 91 5B [ 123 7B {
60 3C < 92 5C \ 124 7C |
61 3D = 93 5D ] 125 7D }
62 3E > 94 5E ^ 126 7E ~
63 3F ? 95 5F _ 127 7F <DEL>
A-3
Extended ASCII Characters
128 80 €
€ 171 AB « 214 D6 Ö
129 81 172 AC ¬ 215 D7 ×
130 82 ‚ 173 AD 216 D8 Ø
131 83 ƒ 174 AE ® 217 D9 Ù
132 84 „ 175 AF ¯ 218 DA Ú
133 85 … 176 B0 ° 219 DB Û
134 86 † 177 B1 ± 220 DC Ü
135 87 ‡ 178 B2 ² 221 DD Ý
136 88 ˆ 179 B3 ³ 222 DE Þ
137 89 ‰ 180 B4 ´ 223 DF ß
138 8A Š 181 B5 µ 224 E0 à
139 8B ‹ 182 B6 ¶ 225 E1 á
140 8C Œ 183 B7 · 226 E2 â
141 8D 184 B8 ¸ 227 E3 ã
142 8E Ž 185 B9 ¹ 228 E4 ä
143 8F 186 BA º 229 E5 å
144 90 187 BB » 230 E6 æ
145 91 ‘ 188 BC ¼ 231 E7 ç
146 92 ’ 189 BD ½ 232 E8 è
147 93 “ 190 BE ¾ 233 E9 é
148 94 ” 191 BF ¿ 234 EA ê
149 95 • 192 C0 À 235 EB ë
150 96 – 193 C1 Á 236 EC ì
151 97 — 194 C2 Â 237 ED í
152 98 ˜ 195 C3 Ã 238 EE î
153 99 ™ 196 C4 Ä 239 EF ï
154 9A š 197 C5 Å 240 F0 ð
155 9B › 198 C6 Æ 241 F1 ñ
156 9C œ 199 C7 Ç 242 F2 ò
157 9D 200 C8 È 243 F3 ó
158 9E ž 201 C9 É 244 F4 ô
159 9F Ÿ 202 CA Ê 245 F5 õ
160 A0 203 CB Ë 246 F6 ö
161 A1 ¡ 204 CC Ì 247 F7 ÷
162 A2 ¢ 205 CD Í 248 F8 ø
163 A3 £ 206 CE Î 249 F9 ù
164 A4 ¤ 207 CF Ï 250 FA ú
165 A5 ¥ 208 D0 Ð 251 FB û
166 A6 ¦ 209 D1 Ñ 252 FC ü
A-4
Extended ASCII Characters (Continued)
167 A7 § 210 D2 Ò 253 FD ý
168 A8 ¨ 211 D3 Ó 254 FE þ
169 A9 © 212 D4 Ô 255 FF ÿ
170 AA ª 213 D5 Õ
Key Code Reference Chart

Key Code ALT+ Value
↑ ALT+128
↓ ALT+129
→ ALT+130
← ALT+131
Insert ALT+132
Delete ALT+133
Home ALT+134
End ALT+135
Page Up ALT+136
Page Down ALT+137
Right ALT ALT+138
Right CTRL ALT+139
Reserved ALT+140
Reserved ALT+141
Numeric Keypad Enter ALT+142
Numeric Keypad / ALT+143
F1 ALT+144
F2 ALT+145
F3 ALT+146
F4 ALT+147
F5 ALT+148
F6 ALT+149
F7 ALT+150
Code Page Mapping of Printed Bar Codes

one the host program is expecting. If this is the case, select the code page with
A-5
which the bar codes were created. The data characters should then appear
properly.
Note: The Code Page option is available for Code 39, Code 93, and Code 128.
Code Page Standard Description

1 CP ISO646
2 (Default) ISO 2022 Automatic National Replacement Charac-
ters
3 CP Binary
82 ISO 2022 11 Swe Swedish Replacement Characters
83 ISO 2022 69 Fra French/Belgium Replacement Characters
81 ISO 2022 25 Fra French/Belgium Replacement Characters
84 ISO 2022 11 Ger German Replacement Characters
85 ISO 2022 11 Ita Italian Replacement Characters
86 ISO 2022 11 Swi Swiss Replacement Characters
87 ISO 2022 11 UK British Replacement Characters
88 ISO 2022 11 Dan Danish Replacement Characters
89 ISO 2022 11 Nor Norwegian Replacement Characters
90 ISO 2022 11 Spa Spanish Replacement Characters
A-6
Sample Symbols
UPC A
0 123456 7890 Interleaved 2 of 5
1234567890
Code 128
Code 128
EAN 13
9 780330 290951
EAN 8
654 3210 5
UPC-E
0 456123 8
Sample Symbols
Code 39
Codabar
BC321
Code 93 A13579B
123456-9$
Straight 2 of 5 Industrial
123456
Matrix 2 of 5
6543210
GS1 DataBar
(01)00123456789012
Programming Chart
9
Programming Chart
Save
Discard
Note: If you make an error while scanning the letters or digits (before scanning
Save), scan Discard, scan the correct letters or digits, and Save again.
Programming Chart
9
Honeywell Scanning & Mobility
9680 Old Bailes Road
Fort Mill, SC 29707
www.honeywellaidc.com
HP1300-UG Rev A
1/11

Hyperion 1300g: User's Guide

Uploaded by

Copyright:

Available Formats

Hyperion 1300g: User's Guide

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hyperion 1300g: User's Guide

Uploaded by

Copyright:

Available Formats

Hyperion 1300g

General Purpose Handheld Linear Scanner

Chapter 1 - Getting Started

Chapter 2 - Programming the Interface

Chapter 3 - Input/Output Settings

Chapter 4 - Data Editing

Chapter 5 - Data Formatting

Chapter 7 - Interface Keys

Chapter 9 - Serial Programming Commands

Chapter 10 - Product Specifications

Chapter 12 - Customer Support

Caution: Any changes or modifications made to this equipment not

Note: To maintain compliance with EMC Regulations, cables connected to

Conformité à la règlementation canadienne

GS Mark Applicable if GS logo is marked on product to indicate

Conforms to AS/NZS 3548 EMC requirements.

Applicable if NOM logo is marked on product. Conforms to

About This Manual

Unpacking the Scanner

Connecting with USB

2. The scanner beeps.

Connecting with Keyboard Wedge

3. Turn the terminal/computer power back on. The scanner beeps.

Connecting with RS485

2. Turn the terminal/computer power back on. The scanner beeps.

Good Technique Bad Technique

Menu Bar Code Security Settings

Resetting the Standard Product Defaults

Standard Product Default

Programming the Interface - Plug and Play

IBM PC AT and Compatibles with CR Suffix

Laptop Direct Connect

Laptop Direct Connect

IBM PS2 with CR Suffix

RS232 Serial Port

IBM Port 5B Interface

IBM Port 17 Interface

Symbology Suffix Symbology Suffix

USB IBM SurePos

USB IBM SurePos

Symbology Suffix Symbology Suffix

USB PC or Macintosh Keyboard

USB Keyboard (PC)

USB Keyboard (Mac)

USB HID Bar Code Scanner

USB Serial Commands

USB Serial Emulation

Note: No extra configuration (e.g., baud rate) is necessary.

* CTS/RTS Emulation Off

* ACK/NAK Mode Off

Please refer to Honeywell website (www.honeywellaidc.com) for complete key-

Program Keyboard Country

Keyboard Wedge Modifiers

Automatic Caps Lock

Autocaps via NumLock

Emulate External Keyboard

Windows Mode Control + ASCII

* Control + ASCII Mode Off

DOS Mode Control + ASCII