Panel LCD LP101WH4-SLAA PDF

LP101WH4
Liquid Crystal Display

Product Specification
SPECIFICATION
FOR
APPROVAL
( ) Preliminary Specification
( ◆ ) Final Specification
Title 10.1" HD TFT LCD
Customer Acer SUPPLIER LG Display Co., Ltd.
MODEL WT3 *MODEL LP101WH4

Suffix SLAA
*When you obtain standard approval,
please use the above model name without suffix
APPROVED BY SIGNATURE APPROVED BY SIGNATURE
Mighty Paeng / S.Manager

/
REVIEWED BY
/
M. H. Kim / Manager
/ PREPARED BY
W.J. Jeon/ Enginer
Please return 1 copy for your confirmation with Product Engineering Dept.
your signature and comments. LG Display Co., Ltd
Ver. 1.0 13. Sep. 2012 1 / 28

LP101WH4
Contents
No ITEM Page
COVER 1
CONTENTS 2
RECORD OF REVISIONS 3
1 GENERAL DESCRIPTION 4
2 ABSOLUTE MAXIMUM RATINGS 6
3 ELECTRICAL SPECIFICATIONS
3-1 ELECTRICAL CHARACTREISTICS 7

3-2 INTERFACE CONNECTIONS 8
3-3 LVDS SIGNAL TIMING SPECIFICATIONS 10
3-4 SIGNAL TIMING SPECIFICATIONS 12
3-5 SIGNAL TIMING WAVEFORM 12
3-6 COLOR INPUT DATA REFERENCE 13
3-7 POWER SEQUENCE 14
4 OPTICAL SFECIFICATIONS 16
5 MECHANICAL CHARACTERISTICS 19
6 KEY PART LIST 22
7 RELIABLITY
7-1 ENVIORMENT TEST CONDITIONS 23

7-2 MECHANICAL TEST CONDITIONS 23
8 TOUCH FUNCTION SPECIFICATIONS 24
9 INTERNATIONAL STANDARDS
9-1 SAFETY 25
9-2 EMC 25
10 PACKING
10-1 DESIGNATION OF LOT MARK 26

10-2 PACKING FORM 26
11 PRECAUTIONS 27
Ver. 1.0 13. Sep. 2012 2 / 28

LP101WH4
RECORD OF REVISIONS
EDID
Revision No Revision Date Page Description
ver
0.0 2012. 08. 08 First Draft V0.0
0.1 2012. 08. 13 15 Touch Power Sequence Update V0.0
20,21 2D Drawing Update
1.0 2012.09.13 Final CAS
Ver. 1.0 13. Sep. 2012 3 / 28

LP101WH4
1. General Description
The LP101WH4 is a Color Active Matrix Liquid Crystal Display with an integral LED backlight system. The
matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in
the normally Black mode. This TFT-LCD has 10.1inches diagonally measured active display area with HD
resolution(1366 horizontal by 768 vertical pixel array). Each pixel is divided into Red, Green and Blue sub-
pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is
determined with a 8-bit gray scale signal for each dot, thus, presenting a palette of more than 16,777,216
colors.
The LP101WH4 has been designed to apply the interface method that enables low power, high speed, low
EMI.
The LP101WH4 is intended to support applications where thin thickness, low power are critical factors and
graphic displays are important. In combination with the vertical arrangement of the sub-pixels, the LP101WH4
characteristics provide an excellent flat display
LP101WH4 is the ‘Total solution’ model. It means it includes LCM & TSP
(TSP is assembled by a ‘Direct Bonding’ method)
Power
3.3V Block
Gate Driver Circuit

GMA TFT LCD
1.8V
Reference 1366 X RGB X 768 Pixel

Block
LVDS_clk LVDS
CN1
1pair &
Timing EPI
LVDS_data Control
3pair Block GOE, Source Driver Circuit
GSC, GSP
VLED
LED Backlight Ass'y
FB1~4
Interrupt
VTSP Touch Screen Touch Screen Sensor
I2C(HID) Controller Block
Ver. 1.0 13. Sep. 2012 4 / 28

LP101WH4
General Features
LCM
Active Screen Size 10.1 inches diagonal
Outline Dimension LCM 232.8±0.3 (H) × 138.15±0.3 (V) × 2.40 mm (max.)
Pixel Pitch 0.05430 mm × 0.16290 mm
Pixel Format 1366 horiz. by 768 vert. Pixels RGB strip arrangement
Color Depth 8-bit, 1,6,777,216 colors
315 cd/m2(Typ., @ILED=15mA) (w/ Touch)
Luminance, White
350 cd/m2(Typ., @ILED=15mA) (w/o Touch)
Logic 0.55 W(typ.@Mosaic)
Power Consumption
B/L 1.56 W (typ.@ ILED= 15mA)
Weight LCM 150g (max.)
Display Operating Mode Transmissive mode, normally Black
Surface Treatment Glare, low reflective treatment of the front polarizer, 2H
TSP
Active Screen Size 10.1 inches diagonal
TSP Outline Dimension 254.3±0.1 (H) × 158.0±0.1 (V) × 1.2 mm (max. with resin)
Sensor Active area 227.52(H) × 130.11(V) mm
Cover View Area 223.72(H) × 126.31(V) mm
Sensor Chanel Pitch 4.34mm (X) x 5.48mm (Y), Flooded-X Pattern
Number of Sensor Chanel 30ea(X) x 42ea(Y)
Power Consumption 0.36W (typ. @ VTSP=5V, 1-finger)
Weight 90g (max.)
Display Operating Mode Transmissive mode, normally Black
Surface Treatment AF Coating (8H)
type Projected Capacitive Add-on Touch Sensor Film, GF2
Substrate
Input Method Single & Multi Finger
Cover Glass Gorilla 0.55t
Ver. 1.0 13. Sep. 2012 5 / 28

LP101WH4
2. Absolute Maximum Ratings

The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.
Table 1. ABSOLUTE MAXIMUM RATINGS
Values
Parameter Symbol Units Notes
Min Max
LCM Power Input Voltage VCC -0.3 4.0 VDC at 25  5C
DDC Power Input Voltage VEDID -0.3 6.5 V
Touch Power Input Voltage VTSP -0.3 5.5V VDC at 25  5C
LVDS Input Voltage VSI -0.25 2.5 V
EDID I2C Input Voltage VI2C -0.3 VEDID+1 V
Touch Logic Voltage VIO -0.3 3.7 V
Operating Temperature TOP 0 50 C 1
Storage Temperature HST -20 60 C 1
Operating Ambient Humidity HOP 10 90 %RH 1
Storage Humidity HST 10 90 %RH 1
Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39C Max, and no condensation of water.
90% 80%
60 60%
Wet Bulb 50
Humidity[(%)RH]
Temperature [℃] Storage
40 40%
30 Operation
20
20%
10
0
10%
-20 0 10 20 30 40 50 60 70 80
Dry Bulb Temperature [℃]
Ver. 1.0 13. Sep. 2012 6 / 28

LP101WH4
3. Electrical Specifications
3-1. Electrical Characteristics

LP101WH4 model requires 3 kinds of Power input to operate a LCM normally.
First one is to operate the LCD electronical components & TFT & Liquid crystal
Second one is to operate the LED Back Light
Third one is to operate the TSP
Table 2. ELECTRICAL CHARACTERISTICS

Values
Parameter Symbol Unit Notes
Min Typ Max
LOGIC :
Power Supply Input Voltage VCC 3.0 3.3 3.6 VDC 1
Power Supply Input Current ICC - 166 194 mA 2
Power Consumption Pc - 0.55 0.66 Watt 2
Power Supply Inrush Current ICC_P - - 2000 mA 3

Differential Impedance Zm 90 100 110 Ohm 4
EDID Input Voltage VEDID 3.0 3.3 3.6 V
EDID Input Current IEDID 10 mA
LED Backlight : (without LED Driver)
Operating Current per string ILED 15 mA 5
LED Power Consumption PLED 1.56 1.59 W 6
LED Vf 2.9 2.95 V
Life Time 12,000 - - Hrs 7
Touch Panel
Power Supply Input Voltage VTSP 3.6 5 5.5 V
1-finger 71 82 mA
Power Supply Input Current ITSP 5-finger 65 75 mA
Idle 20 mA
Power Consumption PTSP 0.36 0.41 Watt 8
Ver. 1.0 13. Sep. 2012 7 / 28

LP101WH4
Note)
1. The measuring position is the connector of LCM and the test conditions are under 25℃, fv = 60Hz,
Mosaic pattern.
2. The specified Icc current and power consumption are under
the Vcc = 3.3V , 25℃, fv = 60Hz condition whereas Mosaic pattern
is displayed and fv is the frame frequency.
3. The below figures are the measuring Vcc condition and the Vcc control block LGD used.
The Vcc condition is same the minimum of T1 at Power on sequence.
3.3V
Rising time
Vcc 90%
0V 10%
0.5ms
4. This impedance value is needed to proper display and measured form LVDS Tx to the mating connector.
5. The typical operating current is for the typical surface luminance (LWH) in optical characteristics.
ILED is the current of each LEDs’ string, LED backlight has strings on it.
6. The LED power consumption shown above does not include power of external LED driver circuit
for typical current condition.
7. The life time is determined as the time at which the typical brightness of LCD is 50% compare to that of
initial value at the typical LED current. These LED backlight has 4 strings on it and the typical current
of LED’s string is base on 15mA.
8. The specified ITSP current and power consumption (PTSP) are under
the VTSP = 5V , 25℃, 100Hz at 1-finger and Active mode.
Ver. 1.0 13. Sep. 2012 8 / 28

LP101WH4
3-2. Interface Connections
3-2-1. LCD Control Board Connection
This LCD employs two interface connections, a 39pin connector is used for the module electronics interface
and the other connector is used for the integral backlight system.
The electronics interface connector is a model FH35C-39S-0.3SHW manufactured by HIROSE.
Table 3. MODULE CONNECTOR PIN CONFIGURATION (CN1)
Pin Symbol Description Notes
1 NC No Connection.
2 VCC Power Supply, 3.3V Typ. [Connector]
3 VCC Power Supply, 3.3V Typ. FH35C-39S-0.3SHW(Hirose), 39pin
4 V EDID DDC 3.3V power
5 NC No Connection (Reserved – LCD panel self test enable) [Connector pin arrangement]
6 Clk EDID DDC Clock 1 39
7 DATA EDID DDC Data
8 RIN 0- Negative LVDS differential data input
9 RIN 0+ Positive LVDS differential data input
10 GND Ground 2 38
11 RIN 1- Negative LVDS differential data input [LCD Module Rear View]
13 GND Ground
Cable insert Rear View
16 GND Ground
17 CLKIN- Negative LVDS differential clock input Direction
18 CLKIN+ Positive LVDS differential clock input
Pin1
19 GND Ground
22 GND Ground
23 VTSP Power Supply, 3.6V ~ 5.5V
24 VTSP Power Supply, 3.6V ~ 5.5V
25 GND Ground
26 I2C_CLK I2C Clock for Touch
27 I2C_Data I2C Data for Touch
28 Interrupt MCU(Host) Alert
29 RST Reset for Touch
30 NC No Connection
31 NC No Connection
32 VCD4 LED Cathode Feedback 4
36 NC No Connection
37 VLED Power Supply for LED [Anode]
Ver. 1.0 13. Sep. 2012 9 / 28

LP101WH4
3-3. LVDS Signal Timing Specifications
3-3-1. DC Specification
LVDS -
|VID|
LVDS +
VCM VIN_MAX VIN_MIN

# |VID| = |(LVDS+) – (LVDS-)|
# VCM = {(LVDS+) + (LVDS-)}/2
0V
Symb
Description Min Max Unit Notes
ol
LVDS Differential Voltage |VID| 100 600 mV -
LVDS Common mode Voltage VCM 0.6 1.8 V -
LVDS Input Voltage Range VIN 0.3 2.1 V -
3-3-2. AC Specification
Tclk
LVDS Clock
LVDS Data
tSKEW (Fclk = 1/Tclk)

1) 85MHz > Fclk ≥ 65MHz : -400 ~ +400
tSKEW 2) 65MHz > Fclk ≥ 25MHz : -600 ~ +600
Description Symbol Min Max Unit Notes

85MHz > Fclk ≥
tSKEW - 400 + 400 ps
65MHz
LVDS Clock to Data Skew Margin
65MHz > Fclk ≥
tSKEW - 600 + 600 ps
25MHz
LVDS Clock to Clock Skew Margin (Even
tSKEW_EO - 1/7 + 1/7 Tclk -
to Odd)
Maximum deviation
FDEV - ±3 % -
of input clock frequency during SSC
Maximum modulation frequency
FMOD - 200 KHz -
of input clock during SSC
Ver. 1.0 13. Sep. 2012 10 / 28

LP101WH4
tSKEW_EO
LVDS Odd Clock

Tclk
LVDS Even Clock

Tclk
LVDS Even Data
< Clock skew margin between channel >
Freq.
Fmax
Fcenter * FDEV
Fcenter
Fmin
1
FMOD
Time
< Spread Spectrum >

3-3-3. Data Format
- LVDS 1 Port
RCLK+
RA+/- R3 R2 R1 R0 G0 R5 R4 R3 R2 R1 R0 G0 R5 R4
RB+/- G4 G3 G2 G1 B1 B0 G5 G4 G3 G2 G1 B1 B0 G5
RC+/- B5 B4 B3 B2 DE VSYNC HSYNC B5 B4 B3 B2 DE VSYNC HSYNC
RD+/- G7 G6 R7 R6 X B7 B6 G7 G6 R7 R6 X B7 B6
Previous (N -1 )th Cycle Current ( Nth ) Cycle Next (N +1 ) th Cycle
< LVDS Data Format >
Ver. 1.0 13. Sep. 2012 11 / 28

LP101WH4
3-4. Signal Timing Specifications

This is the signal timing required at the input of the User connector. All of the interface signal timing should be
satisfied with the following specifications and specifications of LVDS Tx/Rx for its proper operation.
Table 5. TIMING TABLE
ITEM Symbol Min Typ Max Unit Note
DCLK Frequency fCLK 69 72 75 MHz 1port
Period tHP 1470 1526 1542
Hsync Width tWH 24 32 40 Tclk
Width-Active tWHA - 1366 -
Period tVP 779 790 801

Vsync
Width tVW 2 5 8 tHP
Width-Active tVWA - 768 -
Horizontal back porch tHBP 72 80 88

tCLK
Data Horizontal front porch tHFP 8 48 48
Enable Vertical back porch tVBP 8 14 20
tHP
Vertical front porch tVFP 1 3 5
3-5. Signal Timing Waveforms Condition : VCC =3.3V
High: 0.7VCC
Data Enable, Hsync, Vsync
Low: 0.3VCC
tCLK
DCLK 0.5 Vcc
tHP
Hsync tWH
tHBP tWHA tHFP
Data Enable
tVP
tWV
Vsync tVFP
tVBP tWVA
Data Enable
Ver. 1.0 13. Sep. 2012 12 / 28

LP101WH4
3-6. Color Input Data Reference

The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the
color ; the higher the binary input, the brighter the color. The table below provides a reference for color
versus data input.
Table 7. COLOR DATA REFERENCE
Input Color Data

RED GREEN BLUE
Color
MSB LSB MSB LSB MSB LSB
R7 R6 R5 R4 R3 R2 R1 R0 R7 R6 R5 R4 R3 R2 R1 R0 R7 R6 R5 R4 R3 R2 R1 R0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Basic Blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Color Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
RED (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED (01) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED … … … …
RED (254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED (255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN (01) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
GREEN ... … … …
GREEN (254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
GREEN (255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
BLUE (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
BLUE (01) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
BLUE … … … …
BLUE (254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
BLUE (255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Ver. 1.0 13. Sep. 2012 13 / 28

LP101WH4
3-7. Power Sequence

3-7-1. Power Sequence for LCM
90% 90%
Power Supply For LCD
VCC
0V 10% 10%
T5 T6 T7
T1 T2
Interface Signal, Valid Data

Vi
(LVDS Signal of Transmitter) 0V
T3 T4
LED B/L Power OFF LED B/L OFF

ON
Table 8. POWER SEQUENCE TABLE

Parameter Value Units
Min. Typ. Max.
T1 0.5 - 10 (ms)
T2 0 - 50 (ms)
T3 200 - - (ms)
T4 200 - - (ms)
T5 0 - 50 (ms)
T6 0 - 10 (ms)
T7 400 - - (ms)
Note)
1. Valid Data is Data to meet “3-3. Signal Timing Specifications”
2. Please avoid floating state of interface signal at invalid period.
3. When the interface signal is invalid, be sure to pull down the power supply for LCD VCC to 0V.
4. LED B/L power must be turn on after power supply for LCD and interface signal are valid.
Ver. 1.0 13. Sep. 2012 14 / 28

LP101WH4
3-7-2. Power Sequence for Touch
90% 90%
Power Supply Input
VTSP 5V
0V 10% 10%
T1 T7
T2
T6
RESET
Reset Active low
CHG T3
State change Interrupt
Interface Signal, Vi
I2C T4 T5
Valid Data
Table 9. POWER SEQUENCE TABLE

Value
Parameter Units
Min. Typ. Max.
T1 0.5 - 10 ms
T2 10 - - ns
T3 - 154 - ms
T4 0.1 - - ms
T5 - - 0.5 ms
T6 0 - - ns
T7 - - 10 ms
Transferring Data Bits

Each data bit transferred on the bus is accompanied by a pulse on the clock line. The level of the data line must
be stable when the clock line is high ; the only exception to this rule is for generating START and STOP conditions.
START and STOP conditions

START and STOP conditions are signaled by changing the level of the SDA line when the SCL line is high.
Ver. 1.0 13. Sep. 2012 15 / 28

LP101WH4
4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 20 minutes in
a dark environment at 25C. The values specified are at an approximate distance 50cm from the LCD surface
at a viewing angle of  and  equal to 0.
FIG. 1 presents additional information concerning the measurement equipment and method.
FIG. 1 Optical Characteristic Measurement Equipment and Method
LCD Module Equipment

Optical Stage(x,y)
500mm±50mm
Table 9. OPTICAL CHARACTERISTICS Ta=25C, VCC=3.3V, fV=60Hz, fCLK= 72MHz, ILED = 15mA
Parameter Symbol Condition Min Typ Max Units Notes

Average Luminance
With Touch
LAVE 268 315 - cd/㎡ 2
5 Points
Average Luminance (ILED= 15mA)
W/o Touch
297 350
5points - 1.20 1.40
Luminance variation  WHITE
13 point - 1.40 1.60 3
C/R - Center 1 Point 500 800 - - 1
Response time - - 25 - ㎳ 4
Horizontal Θ φx(Left,Right) ±80 ±85 -
Viewing
angle Θ φyu(Up) 80 85 - ˚ 5
Vertical
Θ φyd(Down) 80 85 -
RED RX 0.567 0.597 0.627
RY 0.324 0.354 0.384
GREEN GX 0.305 0.335 0.365
Color Coordinates GY 0.537 0.567 0.597
BLUE BX 0.121 0.151 0.181
BY 0.089 0.119 0.149
WHITE WX 0.283 0.313 0.343
WY 0.299 0.329 0.359

Gray Scale - - Gamma 2.2 6
Ver. 1.0 13. Sep. 2012 16 / 28

LP101WH4
Note)
1. Contrast Ratio(CR) is defined mathematically as
Surface Luminance with all white pixels
Contrast Ratio =
Surface Luminance with all black pixels
2. Surface luminance is the average of 5 point across the LCD surface 50cm from the surface with
all pixels displaying white. For more information see FIG 1.
LWH = Average(L1,L2, … L5)
3. The variation in surface luminance , The panel total variation ( WHITE) is determined by measuring LN
at each test position 1 through 17 and then defined as followed numerical formula.
For more information see FIG 2.
Maximum(L1,L2, … L13)
 WHITE =
Minimum(L1,L2, … L13)
4. Response time is the time required for the display to transition from white to black (rise time, Tr R) and
from black to white(Decay Time, TrD). For additional information see FIG 3.
5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined
for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the
LCD surface. For more information see FIG 4.
6. Gray scale specification * fV = 60Hz

Gray Level Luminance [%] (Typ)
L0 0.11
L15 0.22
L31 0.89
L47 2.59
L63 5.58
L79 9.93
L95 15.4
L111 21.6
L127 28.7
L143 35.7
L159 43.3
L175 51.3
L191 59.9
L207 67.3
L223 75.3
L239 85.4
L255 100.0
Ver. 1.0 13. Sep. 2012 17 / 28

LP101WH4
FIG. 2 Luminance
<Measuring point for Average Luminance & measuring point for Luminance variation>
H
10mm A
6 7 8 10mm
2 3
B H,V : ACTIVE AREA
V A : H/4 mm
9 1 10
B : V/4 mm
H : 222.52 mm
4 5 13
11 12 V : 125.11 mm
FIG. 3 Response Time Active Area

The response time is defined as the following figure and shall be measured by switching the input signal
for “black” and “white”.
TrR TrD
%
100
90
Optical
Response
10
0 white white
black
FIG. 4 Viewing angle Normal

Eye Y
<Dimension of viewing angle range>  = 90 , Up
 = 180 ,
Left 
 = 0 ,
Right
 = 270 ,
Down
Ver. 1.0 13. Sep. 2012 18 / 28

LP101WH4
5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model LP101WH (TBD). In addition the
figures in the next page are detailed mechanical drawing of the LCD.
Horizontal 232.8  0.3mm (without bracket length)
Outline Dimension Vertical 138.15  0.3mm (without bracket length)
Thickness 2.40mm (max.)
Horizontal TBD
Bezel Area
Vertical TBD
Horizontal 222.5214mm
Active Display Area
Vertical 125.1072mm
Horizontal 254.3mm
Touch Screen Panel Vertical 158.00mm
Thickness 1.20mm (max)
Weight 150g (Max.) w/o Touch, 240g (Max) w/ Touch
LCD : Glare, low reflective treatment of the front polarizer, 2H

Surface Treatment
Touch : AF Coating, 8H
Viewing Angle Viewing Angle(When Active area can be seen) ≤ 30°
Ver. 1.0 13. Sep. 2012 19 / 28

LP101WH4
<FRONT VIEW>
Ver. 1.0 13. Sep. 2012 20 / 28

LP101WH4
<REAR VIEW>
Ver. 1.0 13. Sep. 2012 21 / 28

LP101WH4
6. Key Part List
NO ITEM Description Specification

1 SW0663 T-Con Siliconworks, LVDS, EPI, 66BGA
2 SW9402 Source Driver IC Siliconworks, EPI, 1026ch, 6/8bit

3 SW8026 Gate Driver IC Siliconworks, 384ch
4 SM4033 PMIC 6 in 1, buck
5 mXT1386E Touch Control IC Atmel, mXT1386E(MCU) + mXT154E(ROIC) 3ea
Ver. 1.0 13. Sep. 2012 22 / 28

LP101WH4
7. Reliability
7-1. Environment test condition
No. Test Item Conditions

1 High temperature storage test Ta= 60C, 240h
2 Low temperature storage test Ta= -20C, 240h
3 High temperature operation test Ta= 50C, 50%RH, 240h
4 Low temperature operation test Ta= 0C, 240h
5 Vibration test (non-operating) Sine wave, 10 ~ 500 ~ 10Hz, 1.5G, 0.37oct/min
3 axis, 1hour/axis
6 Shock test (non-operating) Half sine wave, 180G, 2ms
one shock of each six faces(I.e. run 180G 6ms
for all six faces)
7 Altitude operating 0 ~ 10,000 feet (3,048m) 24Hr
storage / shipment 0 ~ 40,000 feet (12,192m) 24Hr
{ Result Evaluation Criteria }
There should be no change which might affect the practical display function when the display quality
test is conducted under normal operating condition.
Touch sensor should be at room temperature for 24 hours when the reliability test finished.
When the reliability test is over, touch sensor need to be calibrated.
After calibration and execute the function test.
In the standard condition, it should be no touch abnormal function.
7-2. Mechanical test condition

No. Test Item Conditions Pass Criteria Notes
1 4-point Bending Test ASTM C158 4point bending test ≥ 300MPa 1), a ≥ 25mm
2 FPC Pulling Test 25mm/min, pulling angle : 90˚ ≥ 500g/cm 2)
Note 1)
ASTM C158 4point bending test is a common test method used to measure edge strength of glass.
Ver. 1.0 13. Sep. 2012 23 / 28

LP101WH4
Note 2)
It should be cut FPC as 1cm width before FPC pulling test
FPC pulling test condition is peeling speed 25mm/min, pull-up angle 90˚.
Cutting 1cm
8. Touch Function Specifications

8-1. Test Equipment : K-9601 or equivalent
K-9601 is LGD’s standard equipment for touch function test.
Test Pattern & condition observe Win8 Touch Test requirement.
8-2. Touch function specification
Touch function is satisfied with Win8 Touch requirement.
Ver. 1.0 13. Sep. 2012 24 / 28

LP101WH4
9. International Standards
9-1. Safety
a) UL 60950-1, Underwriters Laboratories Inc.
Information Technology Equipment - Safety - Part 1 : General Requirements.
b) CAN/CSA C22.2 No.60950-1-07, Canadian Standards Association.
c) EN 60950-1, European Committee for Electrotechnical Standardization (CENELEC).
d) IEC 60950-1, The International Electrotechnical Commission (IEC).
9-2. EMC
a) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHZ to 40GHz. “American National Standards Institute(ANSI),
1992
b) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.“ International Special Committee on Radio Interference.
c) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.“ European Committee for Electrotechnical Standardization.(CENELEC), 1998
( Including A1: 2000 )
Ver. 1.0 13. Sep. 2012 25 / 28

LP101WH4
10. Packing
10-1. Designation of Lot Mark
a) Lot Mark
A B C D E F G H I J K L M
A,B,C : SIZE(INCH) D : YEAR

E : MONTH F ~ M : SERIAL NO.
Note
1. YEAR
Year 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020
Mark A B C D E F G H J K
2. MONTH
Month Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec
Mark 1 2 3 4 5 6 7 8 9 A B C
b) Location of Lot Mark

Serial No. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.
10-2. Packing Form
a) Package quantity in one box : 40 pcs
b) Box Size : 478*365*328 mm
Ver. 1.0 13. Sep. 2012 26 / 28

LP101WH4
11. PRECAUTIONS
Please pay attention to the followings when you use this TFT LCD module.
11-1. MOUNTING PRECAUTIONS

(1) You must mount a module using holes arranged in four corners or four sides.
(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the
module. And the case on which a module is mounted should have sufficient strength so that external
force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break
by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental
to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like
chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the adhesives
used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause
chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
11-2. OPERATING PRECAUTIONS

(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage :
V=± 200mV(Over and under shoot voltage)
(2) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after turned on) becomes
longer.
(4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or
electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be
done by system manufacturers. Grounding and shielding methods may be important to minimized the
interference.
Ver. 1.0 13. Sep. 2012 27 / 28

LP101WH4
11-3. ELECTROSTATIC DISCHARGE CONTROL

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.
11-4. PRECAUTIONS FOR STRONG LIGHT EXPOSURE

Strong light exposure causes degradation of polarizer and color filter.
11-5. STORAGE
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the
temperature between 5C and 35C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.
11-6. HANDLING PRECAUTIONS FOR PROTECTION FILM

(1) When the protection film is peeled off, static electricity is generated between the film and polarizer.
This should be peeled off slowly and carefully by people who are electrically grounded and with well
ion-blown equipment or in such a condition, etc.
(2) The protection film is attached to the polarizer with a small amount of glue. If some stress is applied
to rub the protection film against the polarizer during the time you peel off the film, the glue is apt to
remain on the polarizer.
Please carefully peel off the protection film without rubbing it against the polarizer.
(3) When the module with protection film attached is stored for a long time, sometimes there remains a
very small amount of glue still on the polarizer after the protection film is peeled off.
(4) You can remove the glue easily. When the glue remains on the polarizer surface or its vestige is
recognized, please wipe them off with absorbent cotton waste or other soft material like chamois
soaked with normal-hexane.
Ver. 1.0 13. Sep. 2012 28 / 28

LP101WH4
EDID Data for ACER _ ver. 0.0 2012/8/2
Byte Byte Value Value

(Dec) (Hex) Field Name and Comments (Hex) (Bin)
0 00 Header 00 00000000
1 01 Header FF 11111111
2 02 Header FF 11111111
Header
3 03 Header FF 11111111
4 04 Header FF 11111111
5 05 Header FF 11111111
6 06 Header FF 11111111
7 07 Header 00 00000000
8 08 ID Manufacture Name LGD 30 00110000
9 09 ID Manufacture Name E4 11100100
10 0A ID Product Code 03C8h C8 11001000
Vendor / Product
11 0B ( Hex. LSB first ) 03 00000011

EDID Version
12 0C ID Serial No. - Optional ("00h" If not used, Number Only and LSB First) 00 00000000
13 0D ID Serial No. - Optional ("00h" If not used, Number Only and LSB First) 00 00000000
14 0E ID Serial No. - Optional ("00h" If not used, Number Only and LSB First) 00 00000000
15 0F ID Serial No. - Optional ("00h" If not used, Number Only and LSB First) 00 00000000
16 10 Week of Manufacture - Optinal 00 weeks 00 00000000
17 11 Year of Manufacture 2012 years 16 00010110
18 12 EDID structure version # = 1 01 00000001
19 13 EDID revision # = 4 04 00000100
Video input Definition = Input is a Digital Video signal Interface , Colo Bit Depth : 8 Bits per Primary Color ,
20 14
Digital Video Interface Standard Supported: Digital Interface is not defined
A0 10100000
16
Parameters
21 15 Horizontal Screen Size (Rounded cm) = 22 cm 00010110

Display
22 16 Vertical Screen Size (Rounded cm) = 13 cm 0D 00001101

23 17 Display Transfer Characteristic (Gamma) = (gamma*100)-100 = Example:(2.2*100)-100=120 78 01111000
Feature Support [ Display Power Management(DPM) : Standby Mode is not supported, Suspend Mode is not
supported, Active Off = Very Low Power is not supported ,Supportted Color Encoding Formats : RGB 4:4:4
24 18
,Other Feature Support Flags : No_sRGB, Preferred Timing Mode, No_Display is continuous frequency (Multi-
02 00000010
mode_Base EDID and Extension Block).]

25 19 Red/Green Low Bits (RxRy/GxGy) ED 11101101
26 1A Blue/White Low Bits (BxBy/WxWy) E5 11100101
27 1B Red X Rx = 0.597 98 10011000
Coordinates
Panel Color
28 1C Red Y Ry = 0.354 5A 01011010

29 1D Green X Gx = 0.335 55 01010101
30 1E Green Y Gy = 0.567 91 10010001
31 1F Blue X Bx = 0.151 26 00100110
32 20 Blue Y By = 0.119 1E 00011110
33 21 White X Wx = 0.313 50 01010000
34 22 White Y Wy = 0.329 54 01010100
35 23 Established timing 1 ( Optional_00h if not used) 00 00000000
Establ
Timin
ished
gs
36 24 Established timing 2 ( Optional_00h if not used) 00 00000000

37 25 Manufacturer's timings ( Optional_00h if not used) 00 00000000
38 26 Standard timing ID1 ( Optional_01h if not used) 01 00000001
42 2A Standard timing ID3 ( Optional_01h if not used) 01 00000001
Standard Timing ID
43 2B Standard timing ID3 ( Optional_01h if not used) 01 00000001

44 2C Standard timing ID4 ( Optional_01h if not used) 01 00000001
45 2D Standard timing ID4 ( Optional_01h if not used) 01 00000001
46 2E Standard timing ID5 ( Optional_01h if not used) 01 00000001
47 2F Standard timing ID5 ( Optional_01h if not used) 01 00000001
Ver. 1.0 13. Sep. 2012

LP101WH4

54 36 Pixel Clock/10,000 (LSB) 72 MHz @ 59.7 Hz 20 00100000
55 37 Pixel Clock/10,000 (MSB) 1C 00011100
56 38 Horizontal Active (HA) (lower 8 bits) 1366 pixels 56 01010110
57 39 Horizontal Blanking (HB) (lower 8 bits) 160 pixels A0 10100000
58 3A Horizontal Active (HA) / Horizontal Blanking (HB) (upper 4:4bits) 50 01010000
Timing Descriptor #1
59 3B Vertical Avtive (VA) 768 lines 00 00000000

60 3C Vertical Blanking (VB) (DE Blanking typ.for DE only panels) 22 lines 16 00010110
61 3D Vertical Active (VA) / Vertical Blanking (VB) (upper 4:4bits) 30 00110000
62 3E Horizontal Front Porch in pixels (HF) (lower 8 bits) 48 pixels 30 00110000
63 3F Horizontal Sync Pulse Width in pixels (HS) (lower 8 bits) 32 pixels 20 00100000
64 40 Vertical Front Porch in lines (VF) : Vertical Sync Pluse Width in lines (VS) (lower 4 bits) 3 lines : 5 lines 35 00110101
65 41 Horizontal Front Porch/ Sync Pulse Width/ Vertical Front Porch/ Sync Pulse Width (upper 2bits) 00 00000000
66 42 Horizontal Vedio Image Size (mm) (lower 8 bits) 223 mm DF 11011111
67 43 Vertical Vedio Image Size (mm) (lower 8 bits) 125 mm 7D 01111101
68 44 Horizontal Image Size / Vertical Image Size (upper 4 bits) 00 00000000
69 45 Horizontal Border = 0 (Zero for Notebook LCD) 00 00000000
70 46 Vertical Border = 0 (Zero for Notebook LCD) 00 00000000
71 47 Non-Interlace, Normal display, no stereo, Digital Separate [ Vsync_NEG, Hsync_NEG (outside of V-sync) ] 19 00011001
72 48 Flag 00 00000000
73 49 Flag 00 00000000
74 4A Flag 00 00000000
75 4B Data Type Tag (Descriptor Defined by manufacturer ) 00 00000000
76 4C Flag 00 00000000
77 4D Descriptor Defined by manufacturer 00 00000000

78 4E Descriptor Defined by manufacturer 00 00000000
79 4F Descriptor Defined by manufacturer 00 00000000
80 50 Descriptor Defined by manufacturer 00 00000000
90 5A Flag 00 00000000
91 5B Flag 00 00000000
92 5C Flag 00 00000000
93 5D Data Type Tag ( Alphanumeric Data String (ASCII String) ) FE 11111110
94 5E Flag 00 00000000
95 5F Alphanumeric Data String (ASCII String) L 4C 01001100

96 60 Alphanumeric Data String (ASCII String) G 47 01000111
97 61 Alphanumeric Data String (ASCII String) 20 00100000
98 62 Alphanumeric Data String (ASCII String) D 44 01000100
99 63 Alphanumeric Data String (ASCII String) i 69 01101001
100 64 Alphanumeric Data String (ASCII String) s 73 01110011
101 65 Alphanumeric Data String (ASCII String) p 70 01110000
102 66 Alphanumeric Data String (ASCII String) l 6C 01101100
103 67 Alphanumeric Data String (ASCII String) a 61 01100001
104 68 Alphanumeric Data String (ASCII String) y 79 01111001
105 69 Manufacturer P/N(If<13 char--> 0Ah, then terminate with ASCⅡ code 0Ah,set remaining char = 20h) 0A 00001010
106 6A Manufacturer P/N(If<13 char--> 0Ah, then terminate with ASCⅡ code 0Ah,set remaining char = 20h) 20 00100000
107 6B Manufacturer P/N(If<13 char--> 0Ah, then terminate with ASCⅡ code 0Ah,set remaining char = 20h) 20 00100000
Ver. 1.0 13. Sep. 2012

LP101WH4

108 6C Flag 00 00000000
109 6D Flag 00 00000000
110 6E Flag 00 00000000
111 6F Data Type Tag ( Alphanumeric Data String (ASCII String) ) FE 11111110
112 70 Flag 00 00000000
113 71 Alphanumeric Data String (ASCII String) L 4C 01001100

114 72 Alphanumeric Data String (ASCII String) P 50 01010000
115 73 Alphanumeric Data String (ASCII String) 1 31 00110001
118 76 Alphanumeric Data String (ASCII String) W 57 01010111
119 77 Alphanumeric Data String (ASCII String) H 48 01001000
121 79 Alphanumeric Data String (ASCII String) - 2D 00101101
122 7A Alphanumeric Data String (ASCII String) S 53 01010011
123 7B Alphanumeric Data String (ASCII String) L 4C 01001100
Checksum
124 7C Alphanumeric Data String (ASCII String) A 41 01000001

125 7D Alphanumeric Data String (ASCII String) A 41 01000001
126 7E Extension flag (# of optional 128 panel ID extension block to follow, Typ = 0) 00 00000000
127 7F Check Sum (The 1-byte sum of all 128 bytes in this panel ID block shall = 0) 4D 01001101
Ver. 1.0 13. Sep. 2012

Panel LCD LP101WH4-SLAA PDF

Uploaded by

Copyright:

Available Formats

Panel LCD LP101WH4-SLAA PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Panel LCD LP101WH4-SLAA PDF

Uploaded by

Copyright:

Available Formats

LP101WH4

Liquid Crystal Display

Title 10.1" HD TFT LCD

Customer Acer SUPPLIER LG Display Co., Ltd.

MODEL WT3 *MODEL LP101WH4

APPROVED BY SIGNATURE APPROVED BY SIGNATURE

Mighty Paeng / S.Manager

W.J. Jeon/ Enginer

Ver. 1.0 13. Sep. 2012 1 / 28

3-1 ELECTRICAL CHARACTREISTICS 7

7-1 ENVIORMENT TEST CONDITIONS 23

10-1 DESIGNATION OF LOT MARK 26

Ver. 1.0 13. Sep. 2012 2 / 28

Ver. 1.0 13. Sep. 2012 3 / 28

Gate Driver Circuit

Reference 1366 X RGB X 768 Pixel

Ver. 1.0 13. Sep. 2012 4 / 28

Ver. 1.0 13. Sep. 2012 5 / 28

2. Absolute Maximum Ratings

Table 1. ABSOLUTE MAXIMUM RATINGS

DDC Power Input Voltage VEDID -0.3 6.5 V

Touch Power Input Voltage VTSP -0.3 5.5V VDC at 25  5C

LVDS Input Voltage VSI -0.25 2.5 V

EDID I2C Input Voltage VI2C -0.3 VEDID+1 V

Touch Logic Voltage VIO -0.3 3.7 V

Operating Temperature TOP 0 50 C 1

Storage Temperature HST -20 60 C 1

Operating Ambient Humidity HOP 10 90 %RH 1

Storage Humidity HST 10 90 %RH 1

Temperature [℃] Storage

Dry Bulb Temperature [℃]

Ver. 1.0 13. Sep. 2012 6 / 28

3-1. Electrical Characteristics

Table 2. ELECTRICAL CHARACTERISTICS

Power Supply Input Voltage VCC 3.0 3.3 3.6 VDC 1

Power Supply Input Current ICC - 166 194 mA 2

Power Consumption Pc - 0.55 0.66 Watt 2

Power Supply Inrush Current ICC_P - - 2000 mA 3

EDID Input Voltage VEDID 3.0 3.3 3.6 V

EDID Input Current IEDID 10 mA

LED Backlight : (without LED Driver)

Operating Current per string ILED 15 mA 5

LED Power Consumption PLED 1.56 1.59 W 6

LED Vf 2.9 2.95 V

Life Time 12,000 - - Hrs 7

Ver. 1.0 13. Sep. 2012 7 / 28

Ver. 1.0 13. Sep. 2012 8 / 28

Ver. 1.0 13. Sep. 2012 9 / 28

3-3. LVDS Signal Timing Specifications

VCM VIN_MAX VIN_MIN

tSKEW (Fclk = 1/Tclk)

Description Symbol Min Max Unit Notes

Ver. 1.0 13. Sep. 2012 10 / 28

LVDS Odd Clock

LVDS Even Clock

LVDS Even Data

< Clock skew margin between channel >

< Spread Spectrum >

RC+/- B5 B4 B3 B2 DE VSYNC HSYNC B5 B4 B3 B2 DE VSYNC HSYNC