Railway Engineering (CL- 410)

 Geometric Design of a Rail track

 Railway Alignment

1
 Alignment of Railway Lines
• Alignment of railway line refers to the direction and position
given to the centre line of the railway track on the ground in the
horizontal and vertical planes.

• Horizontal alignment means the direction of the railway track in

the plan including the straight path and the curves it follows.

• Vertical alignment means the direction it follows in a vertical

plane including the level track, gradients, and vertical curves.
2
 Basic Requirements of an Ideal Alignment
• Purpose of the New Railway Line
• Integrated Development
• Economic Considerations
– Shortest route
– Construction and maintenance cost
– Minimum operational expenses
• Maximum Safety and Comfort
• Aesthetic Considerations

3
 Factors involved is the selection of a good alignment

1. Choice of Gauge

2. Obligatory or Controlling Points

– Important cities and towns
– Major bridge sites and river crossings
– Existing passes and saddles in hilly terrain
– Sites for tunnels

4
 Factors involved is the selection of a good alignment

3. Topography of the Country

• Plane alignment
• Cross-country alignment
• Mountain alignment
– Zigzag line method
– Switch-back method
– Spiral or complete loop method

5
Factors involved is the selection of a good alignment

6
 Factors involved is the selection of a good alignment

4. Geological Formation
5. Effect of Flood and Climate
6. Position of Roads and Road Crossings
7. Proximity of Labour and Material
8. Location of Railway Stations and Yards
9. Religious and Historical Monuments
10. Cost Considerations
11. Traffic Considerations
12. Economic Considerations

7
Railway Engineering (CL- 410)

 Geometric Design of a Rail track

8
 Geometric Design of Track
The geometric design of a railway track includes all those parameters which
determine or affect the geometry of the track. These parameters are as follows:

• Gradients in the track, including grade compensation, rising gradient, and

falling gradient.
• Curvature of the track, including horizontal and vertical curves, transition
curves, sharpness of the curve in terms of radius or degree of the curve, cant
or super-elevation on curves, etc.
• Alignment of the track, including straight as well as curved alignment.

9
 Necessity for Geometric Design
(a) To ensure the smooth and safe running of trains

(b) To achieve maximum speeds

(c) To carry heavy axle loads

(d) To avoid accidents and derailments due to a defective permanent way

(e) To ensure that the track requires least maintenance.

(f) For good aesthetics

10
 Details of Geometric Design of Track
• Alignment of railway track
• Gradients
• Curves

11
Railway Engineering (CL- 410)

 Geometric Design of a Rail track

 Gradients

12
 Gradients
• Gradients are provided to negotiate the rise or fall in the level
of the railway track.

• A rising gradient is one in which the track rises in the direction

of the movement of traffic and a down or falling gradient is one
in which the track loses elevation in the direction of the
movement of traffic.

13
 Gradients
• A gradient is normally
represented by the distance
travelled for a rise or fall of one
unit.

• Sometimes the gradient is

indicated as per cent rise or fall.
For example, if there is a rise of
1 m in 400 m, the gradient is 1
in 400 or 0.25%.

14
 Gradients
Gradients are provided to meet the following objectives:

• To reach various stations at different elevation

• To follow the natural contours of the ground to the extent
possible
• To reduce the cost of earthwork.

15
 Gradients
The following types of gradients are used on the railways:

(a) Ruling gradient

(b) Pusher or helper gradient
(c) Momentum gradient
(d) Gradients in station yards

16
 Ruling gradient
• The ruling gradient is the steepest gradient that exists in a
section.

• In other words, it is the maximum gradient within which the

designer attempts to design vertical profile of a track.

• It determines the maximum load that can be hauled by a

locomotive on that section.
17
 Ruling gradient
• While deciding the ruling gradient of a section, it is not only the
severity of the gradient but also its length as well as its position
with respect to the gradients on both sides that have to be taken
into consideration.

• The power of the locomotive to be put into service on the track

also plays an important role in taking this decision, as the
locomotive should have adequate power to haul the entire load
over the ruling gradient at the maximum permissible speed.

18
 Ruling gradient
• The extra force P required by a locomotive to pull a train of
weight W on a gradient with an angle of inclination 𝜃 is:

19
 Ruling gradient
• Indian Railways does not specify any fixed ruling gradient
owing to enormous variations in the topography of the
country, the traffic plying on various routes, and the speed
and type of locomotive in use on various sections.

• Generally, the following ruling gradients are adopted on

Indian Railways when there is only one locomotive pulling the
train.
– In plain terrain: 1 in 150 to 1 in 250
– In hilly terrain: 1 in 100 to 1 in 150
20
 Pusher or Helper Gradient
• In hilly areas, the rate of rise of the terrain becomes very
important when trying to reduce the length of the railway
line and, therefore, sometimes gradients steeper than the
ruling gradient are provided to reduce the overall cost.

• In such situations, one locomotive is not adequate to pull the

entire load, and an extra locomotive is required.

21
 Pusher or Helper Gradient
• When the gradient of the ensuing section is so steep as to
necessitate the use of an extra engine for pushing the train, it
is known as a pusher or helper gradient.

• Examples of pusher gradient is the Darjeeling Himalayan

Railway section.

22
 Momentum Gradient
• The momentum gradient is steeper than the ruling gradient
and can be overcome by a train because of the momentum it
gathers while running on the section.

• In valleys, a falling gradient is sometimes followed by a rising

gradient. In such a situation, a train coming down a falling
gradient acquires good speed and momentum, which gives
additional kinetic energy to the train and allows it to
negotiate gradients steeper than the ruling gradient.
23
 Gradients in Station Yards
• The gradients in station yards are quite flat due to
the following reasons:

– To prevent standing vehicles from rolling and moving away

from the yard due to the combined effect of gravity and
strong winds.
– To reduce the additional resistive forces required to start a
locomotive to the extent possible.
24
 Gradients in Station Yards
• It may be mentioned here that generally, yards are not
leveled completely and certain flat gradients are
provided in order to ensure good drainage.

• The maximum gradient prescribed in station yards on

Indian Railways is 1 in 400, while the recommended
gradient is 1 in 1000.
25
 Grade Compensation on Curves
Curves provide extra resistance to the movement of trains.
As a result, gradients are compensated to the following
extent on curves:

• On BG tracks, Minimum of 0.04% per degree of the curve or 70/R,

• On MG tracks, Minimum of 0.03% per degree of curve or 52.5/R
• On NG tracks, Minimum of 0.02% per degree of curve or 35/R
(where R is the radius of the curve in meters)
26
 Grade Compensation on Curves
1. Find the steepest gradient on a 2° curve for a BG line with a
ruling gradient of 1 in 200.

2. What extent should a ruling gradient of 1 in 150 on a broad

gauge line be downgraded to accommodate a 3° curve?
27
Railway Engineering (CL- 410)

 Geometric Design of a Rail track

 Superelevation

28
 Superelevation
• In order to counteract the effect of centrifugal force and to
reduce the tendency of the train to overturn or skid, the outer
rail is raised with respect to inner rail, thus providing transverse
slope throughout the length of the horizontal curve. This
transverse inclination to outer rail is known as Superelevation
or cant.

• The inner rail is taken as the reference rail and is normally

maintained at its original level. The inner rail is also known as
the gradient rail.
29
 Superelevation
Cant deficiency:

• Cant deficiency (Cd) occurs when a train travels around a curve at a

speed higher than the equilibrium speed.

• It is the difference between the theoretical cant required for such

high speeds and the actual cant provided.

(The equilibrium speed, as such, is the speed at which the effect of the
centrifugal force is completely balanced by the cant provided.)
30
 Superelevation
Cant excess:

• Cant excess (Ce) occurs when a train travels around a curve at a

speed lower than the equilibrium speed.

• It is the difference between the actual cant provided and the

theoretical cant required for such a low speed.

31
 Superelevation
Centrifugal Force on a Curved Track:

• A vehicle has a tendency to travel in a straight direction, which

is tangential to the curve, even when it moves on a circular
curve. As a result, the vehicle is subjected to a constant radial
acceleration:
V2
Radial acceleration = g =
R
where V is the velocity (m/s) and R is the radius of curve (m).
32
 Superelevation
Centrifugal Force on a Curved Track:

• This radial acceleration produces a centrifugal force which acts in a radial

direction.
• The value of the centrifugal force is given by the formula:

Force = mass × acceleration

V2 W V2
F=mx = x
R g R

where F is the centrifugal force (tones), W is the weight of the vehicle (tones), V
is the speed (metre/sec), g is the acceleration due to gravity (metre/sec2), and R is
the radius of the curve (metre).
33
 Superelevation
Centrifugal Force on a Curved Track:

• To counteract the effect of the centrifugal force, the outer rail of the curve
is elevated with respect to the inner rail by an amount equal to the
superelevation.

• A state of equilibrium is reached when both the wheels exert equal

pressure on the rails and the superelevation is enough to bring the
resultant of the centrifugal force and the force exerted by the weight of
the vehicle at right angles to the plane of the top surface of the rails.

• In this state of equilibrium, the difference in the heights of the outer and
inner rails of the curve known as equilibrium superelevation.
34
 Superelevation
Equilibrium Superelevation:

35
 Superelevation
Equilibrium Superelevation:

where e is the equilibrium superelevation, G is the gauge,

V is the velocity, g is the acceleration due to gravity, and R is
the radius of the curve.
36
 Superelevation
Thumb Rules for Calculating Superelevation in the Field:

37
 Superelevation
Thumb Rules for Calculating Superelevation in the Field:

• For example, if the maximum sanctioned speed (MSS) of the

section is 100 km/h, the equilibrium speed may be taken as
75% of the MSS, i.e., 75 km/h. The superelevation for a 1°
curve as calculated by the thumb rule is as follows:

38
 Superelevation
Negative Superelevation:

39
 Superelevation
The provision of negative superelevation for the branch line and the
reduction in speed over the main line can be calculated as follows:

1. The equilibrium superelevation for the branch line curve is first calculated
using the formula.
2. The equilibrium superelevation e is reduced by the permissible cant
deficiency Cd and the resultant superelevation to be provided is:

where, x is the superelevation, e is the equilibrium superelevation, and Cd is 75

mm for BG and 50 mm for MG. The value of Cd is generally higher than that of e,
and, therefore, x is normally negative. The branch line thus has a negative
superelevation of x. 40
 Superelevation
The provision of negative superelevation for the branch line and the
reduction in speed over the main line can be calculated as follows:

(3)
The maximum permissible speed on the main line, which has a superelevation of
x, is then calculated by adding the allowable cant deficiency (x + Cd). The safe
speed is also calculated and smaller of the two values is taken as the maximum
permissible speed on the main line curve.

41
 Safe Speed on Curves
For all practical purposes safe speed means a speed which protects a carriage from the
danger of overturning and derailment and provides a certain margin of safety. Earlier it
was calculated empirically by applying Martin’s formula:

42
 Safe Speed on Curves
New Formula for Determining Maximum Permissible Speed on Transitioned
Curves:

where V is the maximum speed in km/h, Ca is the actual cant in mm, Cd is the
permitted cant deficiency in mm, and R is the radius in m.
43
Railway Engineering (CL- 410)

 Geometric Design of a Rail track

 Curves

44
 Curves in Railway geometry
• Curves are introduced on a railway track to bypass obstacles, to
provide longer and easily traversed gradients, and to pass a
railway line through obligatory or desirable locations.

• Horizontal curves are provided when a change in the direction of

the track is required and vertical curves are provided at points
where two gradients meet or where a gradient meets level
ground.

45
 Objections to the provision of the curve
• Prevent use of heavy locomotive
• Possibility of derailment
• Unequal distribution of load
• Running not smooth on curve/ speed reduced
• Many fittings are required

46
 Places to avoid
• Bridges and tunnels
• Level crossing
• Bridge approaches
• Station-yard approaches
• Steep gradients
• Deep cuttings

47
 Classification of the curves
• Simple (circular) curves
• Parabolic curves
• Compound curves
• Transitional curves

48
 Simple (circular) curves
• Simple (circular) curve is an arc of a circle.

• A curve is defined either by its radius or by its degree. The

degree of a curve (D) is the angle subtended at its centre by a
30.5-m or 100-ft chord.

• Radius of curve = 1720 / Degree of curve (Chord length = 30m)

(A 2° curve, therefore, has a radius of 1720/2 = 860 m.)

49
 Simple (circular) curves
• Relationship between radius and
versine of a curve:

• AC and DE being two chords meeting

perpendicularly at a common point B,
simple geometry can prove that
AB × BC = DB × BE or
V(2R – V) = (C/2) × (C/2)

50
 Simple (circular) curves

Determination of degree of a curve in field:

• For determining the degree of the curve in the field, a chord

length of either 11.8 m or 62 ft is adopted.

51
 Simple (circular) curves
Maximum Degree of a Curve:

• The maximum permissible degree of a curve on a track

depends on various factors such as gauge, wheel base of the
vehicle, maximum permissible superelevation, and other
such allied factors.

52
 Elements of a circular curve
• Tangent points
• Versine (EF)
• Chord
• Tangents
• Angle of intersection
• Angle of deflection

53
 Elements of a circular curve
• important relations between these elements:

54
 Setting Out a Circular Curve
A circular curve is generally set out by any one of the following
methods:

• Tangential offset method

• Long chord offset method
• Quartering of versine method
• Chord deflection method
• Theodolite method
55
 Compound curves
• These are the curves which are composed of two or more
simple curves of different radii, arranged in a such a way
that they are tangential to each other.

• They are used when compelled by the topography to avoid

the obstructions.

56
 Parabolic curves
• These curves have got the quality of being easily laid by the
offset method.

• These are exclusively used as vertical curves in railways and

highways.

• The equation of parabolic curve is y = 𝑘 2

57
 Transition Curves
• As soon as a train commences motion on a circular curve
from a straight line track, it is subjected to a sudden
centrifugal force, which not only causes discomfort to the
passengers but also distorts the track alignment and affects
the stability of the rolling stock.
• In order to smoothen the shift from the straight line to the
curve, transition curves are provided on either side of the
circular curve so that the centrifugal force is built up
gradually as the superelevation slowly runs out at a uniform
rate
58
 Transition Curves
• A transition curve is, therefore, the cure for an uncomfortable
ride, in which the degree of the curvature and the gain of
superelevation are uniform throughout its length, starting
from zero at the tangent point to the specified value at the
circular curve.

59
 Objectives of a transition curve
• To decrease the radius of the curvature gradually in a planned way
from infinity at the straight line to the specified value of the radius
of a circular curve in order to help the vehicle negotiate the curve
smoothly.

• To provide a gradual increase of the superelevation starting from

zero at the straight line to the desired superelevation at the circular
curve.

• To ensure a gradual increase or decrease of centrifugal forces so as

to enable the vehicles to negotiate a curve smoothly.

60
 Requirements of an Ideal Transition Curve
• It should be tangential to the straight line of the track, i.e., it should
start from the straight part of the track with a zero curvature.

• It should join the circular curve tangentially, i.e., it should finally have
the same curvature as that of the circular curve.

• Its curvature should increase at the same rate as the superelevation.

• The length of the transition curve should be adequate to attain the

final superelevation, which increases gradually at a specified rate.
61
Types of Transition Curves

62
 Length of Transition Curve
• The length of the transition curve prescribed on Indian
Railways is the maximum of the following three values:

• where L is the length of the curve in m, Ca is the actual cant

or superelevation in mm, Cd is the cant deficiency in mm and
Vm is maximum speed.
• Maximum change of cant is taken as 55 mm/sec 63
 Length of Transition Curve
Other provisions made to meet the requirements of special
situations are as follows:

• When deciding the length of transition curves, particularly on high-speed

routes, future speeds expected to be implemented on those tracks, such
as 160 km/h for group A routes and 130 km/h for group B routes, may be
taken into account.
• In exceptional cases, when there is no space available for providing full
length transition curves, particularly on high-speed routes as per the
preceding calculations, the length of the transition curve may be reduced
to two-thirds of the desirable length as worked out by Eqns (1) & (2)
64
 Shift of curve
• For the main circular curve to fit in
the transition curve, which is laid in
the shape of a cubic parabola, it is
required be moved inward by a
measure known as the ‘shift’. The
value of shift can be calculated
using the formula:

• where S is the shift in m, L is the

length of the transition curve in m,
and R is the radius in m.
65
 Vertical Curves
• An angle is formed at the point where two different gradients meet,
forming a summit or a sag.

66
 Existing Provisions on Indian Railways
• As per the existing provisions, vertical curves are provided only at
the junction of gradients, when the algebraic difference between
the gradients is equal to or more than 0.4 per cent. The minimum
radii for vertical curves are given in Table:

67
 Length of a Vertical Curve (Old Method)
• The length of a vertical curve depends upon the algebraic difference
between the gradients and the type of curve formed (summit or
sag).
• The required length of a vertical curve for achieving the maximum
permissible speed is given by the formula:

• where L is the length of the vertical curve in m, a is the per cent

algebraic difference between successive gradients, and r is the rate
of change of the gradient, which is 0.1% for summit curves and
0.05% for sag curves.
68
 Length of a Vertical Curve (Old Method)
Example:
Calculate the length of the vertical curve between two
gradients meeting in a summit, one rising at a rate of 1
in 100 and the other falling at a rate of 1 in 200.

69
 Length of a Vertical Curve (Old Method)
Example:
Calculate the length of the vertical curve between two gradients meeting in a
summit, one rising at a rate of 1 in 100 and the other falling at a rate of 1 in 200.

70