Conefor Inputs

“Conefor Inputs” is a custom-made GIS extension for ArcView 3.x, ArcGIS 9.x and
ArcGIS 10 developed by Jeff Jenness Enterprises (www.jennessent.com) specifically
for the Conefor Sensinode software (CS).

The instructions for installation and use of the extension provided below have also
been included as part of the CS user’s manual. CS software and manual can be
freely downloaded from http://www.conefor.org.

“Conefor Inputs” allows easily obtaining from a theme in ArcGIS (e.g. shapefile)
both the node file and the connection file (as a distance file) directly in the format
required by CS. The distances in the connection file calculated by this extension are
edge-to-edge Euclidean (straight-line) between all the features (e.g. patches) of a
theme, with the option to analyse either all features or only those within a specified
distance (see below). The node and distance files provided by this extension are
directly usable (with no change) in CS.

Installation

For ArcView 3.x

1) Begin by placing the "conefor_inputs.avx" file into the ArcView extensions

directory (../../Av_gis30/Arcview/ext32/). This file is available for download at
http://www.conefor.org or
http://www.jennessent.com/arcgis/conefor_inputs.htm.

2) After starting ArcView, load the extension by clicking on File --> Extensions… ,
scrolling down through the list of available extensions, and then clicking on the
checkbox next to the extension called "Conefor Inputs".

3) The Conefor Inputs tool will appear in your View button bar as a button with a
“D” on it:

For ArcGIS 9.x

1) Make sure ArcGIS is closed.

2) Install the Conefor Inputs extension by double-clicking on the file

“Conefor_inputs.exe”, which will be located in the “Extensions GIS\ArcGIS 9.x”
folder (within the folder where you installed CS, typically C:\Program
files\Conefor Sensinode 22, or some other similar path), and follow the
instructions. This installation file is also available at http://www.conefor.org or
http://www.jennessent.com/arcgis/conefor_inputs.htm. The installation routine
will register the Conefor_inputs.dll with all the required ArcMap components.

3) Start ArcMap.

1
For ArcGIS 10

1) Make sure ArcGIS is closed.

2) Install the tool on your hard drive by running the file “Conefor_inputs_10.EXE”,
which will be located in the “Extensions GIS\ArcGIS 9.x” folder (within the
folder where you installed CS, typically C:\Program files\Conefor Sensinode 22,
or some other similar path), and follow the instructions. This installation file is
also available at http://www.conefor.org or
http://www.jennessent.com/arcgis/conefor_inputs.htm. This installation routine
will install the DLL and several ancillary files on your hard drive, but will not
register the tool with ArcGIS.

3) Use Windows Explorer to open your installation folder. If you used the default
installation values, then this folder will be located at “Program Files\Conefor
Inputs\”. This folder will also include some additional files and this manual.

4) For Windows XP: Double-click the file

“Conefor_Inputs_ArcGIS_10_Installer.bat” to register the tool with ArcGIS 10.0.

For Windows 7/Vista: Right-click the file

“Conefor_Inputs_ArcGIS_10_Installer.bat” and then click “Run as Administrator
to register the tool with ArcGIS 10.0.

If the registration is successful, then you should see a “Registration Succeeded”

notice.

2
 Note: For the concerned or curious, the batch file Conefor_Inputs_ArcGIS_10_
Installer.bat contains the following single line of text:

"%CommonProgramFiles%\ArcGIS\bin\ESRIRegAsm.exe" /p:Desktop "Conefor_inputs.dll"

/f:"Conefor.reg"

It directs the ESRI installer ESRIRegAsm to register the extension DLL

Conefor_inputs.dll within ArcGIS, using GUID and Class ID values from the
registry file Conefor.reg (also located in your installation directory). Both
Conefor_inputs_ArcGIS_10_Installer.bat and Conefor.reg may be opened and
viewed using standard text editors such as Notepad or WordPad.

5) Alternative Method if you do not get the “Registration Succeeded”

message: If the method above does not work, the reason is probably due to
the “%CommonProgramFiles” environmental variable pointing to the wrong
location, and/or Windows Vista or Windows 7 Security settings. The fix is to use
a batch file that includes the full pathnames to “ESRIRegAsm.exe” and to the
extension DLL and REG files. You may edit the BAT file yourself, or you may
use the tool Make_Batch_Files.exe (located in your installation folder) to
create new registration and unregistration batch files that are properly
formatted to your system.
If using Windows XP: Simply double-click on the file
Make_Batch_Files.exe to create the new batch files.
If using Windows Vista or Windows 7: Right-click on the file
Make_Batch_Files.exe and click “Run as Administrator” to create the new
batch files.

Repeat Step 4 above to register the tool in ArcGIS 10, but this time use the new
BAT file Register_Conefor_ID.bat.
6) Start ArcMap

The default install location for the extension is a folder named “Conefor Inputs”
inside the folder “Program Files”, which will also include some additional files
required by the extension and this manual. This folder should better be editable to

3
the user (i.e. not restricted to administrators), since this extension occasionally
writes to a file located in this folder. The extension should not crash if it is unable to
write to this folder, but it will run better if it can.

This tool is installed as an Extension in ArcMap, although it is a type of extension

that does not show up in the list of extensions available in the “Tools” menu.

Viewing the Tool

After installing the extension, you should see the following new toolbar in your map
(it may also be embedded in your standard ArcMap toolbars, rather than as a
standalone object):

If you do not see this toolbar, then open your “Customize” tool (by either double-
clicking on a blank part of the ArcMap toolbar, or by clicking the “Tools” menu, then
“Customize”), click the “Toolbars” tab and check the box next to “Conefor”.

You should now see your Conefor toolbox in ArcMap.

Uninstalling the Tool

Uninstalling the tool ArcGIS 9.x:

1) Close ArcMap

2) Click the Windows “Start” button, then “Control Panel”, then “Add or Remove
Programs”. Find “Conefor Inputs”, click the “Remove” button and follow the
instructions to remove it.

4
Uninstalling the tool in ArcGIS 10.0:

1) Close ArcMap

2) Use Windows Explorer to open your installation folder. If you used the default
installation values, then this folder will be located at “Program Files\Conefor
Inputs\”. This folder will also include some additional files and this manual.

3) For Windows XP: Double-click the file “Uninstall_Conefor_Inputs.bat” to

unregister the tool with ArcGIS 10.0.

For Windows 7/Vista: Right-click the file “Uninstall_Conefor_Inputs.bat” and

click “Run as Administrator” to unregister the tool with ArcGIS 10.0.

5
 If the unregistration is successful, then you should see a “Unregistration
Succeeded” notice.

4) Alternative Method if you do not get the "Unregistration Succeeded"

message: If the method above does not work, the reason is probably due to
the "%CommonProgramFiles" environmental variable pointing to the wrong
location, and/or Windows Vista or Windows 7 Security settings. The fix is to use
a batch file that includes the full pathnames to "ESRIRegAsm.exe" and to the
extension DLL and REG files. You may edit the BAT file yourself, or you may
use the tool Make_Batch_Files.exe (located in your installation folder) to create
new registration and unregistration batch files that are properly formatted to
your system.
If using Windows XP: Simply double-click on the file Make_Batch_Files.exe
to create the new batch files.
If using Windows Vista or Windows 7: Right-click on the file
Make_Batch_Files.exe and click "Run as Administrator" to create the new batch
files.

Repeat Step 3 above to unregister the tools in ArcGIS 10, but this time use the
new BAT file Unregister_Conefor_ID.bat.
5) Click the Windows “Start” button, then “Control Panel”, then “Add or Remove
Programs”. Find “Conefor Inputs 10”, click the “Remove” button and follow the
instructions to remove it.

6
Note: For the concerned or curious, the batch file Uninstall_Conefor_Inputs.bat
contains the following single line of text:

"%CommonProgramFiles%\ArcGIS\bin\ESRIRegAsm.exe" /p:Desktop /u "Conefor_inputs.dll"

It directs the ESRI installer ESRIRegAsm to unregister the DLL within ArcGIS.
Uninstall_Conefor_Inputs.bat may be opened and viewed using standard text
editors such as Notepad or WordPad.

7
Use of the extension

The extension tool consists of only two buttons: the one in the left (“D”) opens the
dialog for obtaining the node and distance files, while the one in the right just
opens this help file.

After clicking the “D” button the “ID Within Distance Parameters” dialog will be
shown:

In the “ID Within Distance Parameters” dialog proceed as follows:

1) Select the layer or layers with the habitat data (where each feature will be
considered as a different node in the resultant files).

8
The layers should be already open (added) in ArcMap/ArcGIS. Note that this tool
will always analyze all the features in each selected layer. It will not restrict
analysis to only the selected features. Note that all the layers should have the same
ID and attribute fields (name and format), as described in the next two steps.

2) Select the field in the layer containing a unique ID for each node (feature in the
layer).

This ID field should be already prepared in your layer before opening the dialog. In
case your layer does not contain this ID field, you can easily obtain it in ArcGIS 9.x
by creating a new field (Add field… in the layer Attributes table), typically of Short
Integer type, and by calculating the ID values in that field for each feature as 1 +
the FID field in your layer. The FID field contains a unique ID for each feature in
your layer, starting from 0 up to the number of features-1, and should typically be
the first and leftmost field in your attribute table. FID is an ‘internal’ field that will
not show up in the list of fields to be selected in the dialog, but the field you create
from that FID as described above will appear in the dialog.

3) Select the field in the layer containing the attribute of the nodes (e.g. habitat
area, habitat quality, quality-weighted area, etc.). This attribute field should be as
well calculated and available in the layer before starting the dialog.

4) Choose whether to calculate distances based on edge-to-edge distances,

geometric centroid-to-geometric centroid distances, or spherical centroid-to-
spherical centroid distances. Spherical centroids are calculated from the shape of
the feature as it lies on a sphere approximating the surface of the planet. Spherical
centroids more accurately reflect the true centre of gravity of a feature, but they
take longer to calculate. Note: This option only applies to the ArcGIS 9.x and 10
versions of Conefor inputs. This option is not available in the ArcView 3.x version.

5) Select if you intend to calculate distances to either all other features in the layer
(this will correspond to a full connection file, as described in section 5.3), or only
those features that are within a specified distance (this will correspond to a partial
connection file, as described in section 5.3 of the Conefor Sensinode 2.2 users’
manual). In this latter case the distance threshold must be entered in the same
units of the actual feature class projection (“Include features within xxxxx Map
units”).

The distance threshold option is particularly useful for reducing the processing time
in the distance calculations through the GIS, when a significant proportion of the
pairs of patches are too distant from each other to be directly connected. This may
be the case for themes covering large geographical regions. If for example the
maximum dispersal distance of the analysed species is 5 km, it makes no sense
spending time in calculating distances between patches that are separated by
dozens of kilometres. In this case, restrict the analysis to features within 5 km, and
only the pairs of features within that distance will be included in the output. All the
nodes (features) not present in the distance/connection file will be considered
completely directly unconnected in CS (e.g. by being further apart than 5 km in the
previous example), as described in section 5.3 of the Conefor Sensinode 2.2 users’
manual.

Note that if you select multiple layers to analyze, then the ID and Attribute Field
listboxes will only show those fields from the first selected layer. This extension will
assume that all selected layers will have the ID and Attribute fields that you select.

6) Select the output option “ASCII text file of distances to each feature”, which is
the output file that can be directly used in CS.

9
The distance file will be named “Distances_[Layer Name]_X.txt”, where [Layer
Name] is the name of the input layer being analyzed, and “X” is a number that
guarantees that this is a unique filename. The first such file created in this folder
will be named “Distances_[Layer Name].txt”; the second will be named
“Distances_[Layer Name]_2.txt”, etc. The file contains three columns of data,
representing the ID of node i, the ID of node j, and the Euclidean distance between
nodes i and j, as described for the connection file format in section 5.3 of the
Conefor Sensinode 2.2 users’ manual. Note that the extension will only calculate
the distance between any pair of features one time. If the tool has already
calculated the distance from i to j, it will not recalculate the distance from j to i.
Furthermore, the distance will only be entered into the distance file once, as
required by CS. If the file has an entry for the distance from i to j, the file will not
also have an entry for the distance from j to i (as required by CS).

The extension will also automatically generate the node file in the format required
by CS, containing two columns of data, the first representing the node ID and the
second containing the attribute value for that node (see section 4.2). The file will be
named “Nodes_[Layer Name]_X.txt”, where “X” is a number that guarantees that
this is a unique filename. The first such file created in this folder will be named
“Nodes_[Layer Name].txt”; the second will be named
“Nodes_[Layer_Name]_2.txt”, etc.

7) Select the folder where the node and distance files will be saved. Note that you
just have to select the folder (one click) and not to open the folder (the output file
names are fixed as described above).

8) Decide whether you would like to automatically open all new files for viewing.

Upon completion, the tool will optionally open all the tables and text files it
produced (for you to view them), and it will also summarize the processing in a
simple “Analysis report”.

10
Note that the processing slows down with large shapefiles (that is, with increasing
number of polygon features). Also, highly complex features can slow down the
computation time when calculating distances between them. Polygons with lots of
vertices will take longer to analyse than polygons with few vertices. Some previous
processing to reduce the total number of vertices describing the polygon boundaries
(especially removing redundant vertices if there are some) may benefit the speed
of the distance computation through this extension.

11
Troubleshooting
If Any of the Tools Crash
If a tool crashes, you should see a dialog that tells us what script crashed and
where it crashed. I would appreciate it if you could copy the text in that dialog, or
simply take screenshots of the dialog and email them to me at
[email protected]. Note: Please make sure that the line numbers are visible
in the screenshots! The line numbers are located on the far right side of the text.
Use the scrollbar at the bottom of the dialog to make the line numbers visible.
“Object variable or With block variable not set” Error:
If you open ArcMap and immediately see the error dialog appear with one or more
error messages stating that “Object variable or With block variable not set”, then
90% of the time it is because ArcGIS was running when you installed the extension.
The “Object” variable being referred to is the “Extension” object, and ArcGIS only
sets that variable when it is initially turned on.
The solution is usually to simply close ArcGIS and restart it. If that does not work,
then:
1) Close ArcGIS
2) Reinstall the extension
3) Turn ArcGIS back on.
RICHTX32.OCX Error (also comct332.ocx, comdlg32.ocx, mscomct2.ocx,
mscomctl.ocx, msstdfmt.dll errors):
If you see a line in the error dialog stating:
Component 'RICHTX32.OCX' or one of its dependencies not correctly registered: a file is
missing or invalid

Or if you see a similar error stating that one or more of the files comct332.ocx,
comdlg32.ocx, mscomct2.ocx, mscomctl.ocx or msstdfmt.dll are missing or invalid,
then simply follow the instructions for RICHTX32.OCX below, but substitute the
appropriate file for RICHTX32.OCX.
This error is almost always due to the fact that new installations of Windows 7 and
Windows Vista do not include a file that the extension expects to find. For
example, the file “richtx32.ocx” is actually the “Rich Text Box” control that appears
on some of the extension dialogs. The other files refer to other common controls
that might appear on the various extension dialogs.
The solution is to manually install the missing file (richtx32.ocx) yourself. Here is
how to do it:
1) Open Windows Explorer and locate the file richtx32.ocx in your extension
installation file.
2) If you are running a 32-bit version of Windows, then copy richtx32.ocx to
the directory
C:\Windows\System32\
If you are running a 64-bit version of Windows, then copy richtx32.ocx to
the directory
C:\Windows\SysWOW64\
3) Open an “Elevated Command Prompt” window. This is the standard
Windows Command Prompt window, but with administrative privileges
enabled. You need these privileges enabled in order to register the OCX
with Windows. Note: The Elevated Command Prompt opens up in the

12
“..\windows\system32” directory, not the “..\Users\[User Name]” directory.
The window title will also begin with the word “Administrator:”

a. Method 1: Click the “Start” button, then “All Programs”, then

“Accessories” and then right-click on “Command Prompt” and select
Run as Administrator.
b. Method 2: Click the “Start” button, and then click on the “Search
Programs and Files” box. Type “cmd” and then click
CONTROL+SHIFT+ENTER to open the Command window with
Administrator privileges.

For more help on opening an Elevated Command Prompt, please refer to:
http://www.sevenforums.com/tutorials/783-elevated-command-
prompt.html
http://www.winhelponline.com/articles/158/1/How-to-open-an-elevated-
Command-Prompt-in-Windows-Vista.html
Or simply do a search for “Elevated Command Prompt”.

13
 4) Register the file richtx32.ocx using the Windows RegSvr function:
a. If using a 32-bit version of Windows, type the line
regsvr32.exe c:\windows\system32\richtx32.ocx

b. If using a 64-bit version of Windows, type the line

regsvr32.exe %windir%\syswow64\richtx32.ocx

c. Click [ENTER] and you should see a message that the registration
succeeded.

--------------------------------------------

14
Tool updated December 2, 2010 (Ver. 1.0.133) to allow for distance by centroids.

Tool updated June 9, 2011 (Ver. 1.0.150) to update error-checking code.

Tool updated June 27, 2011 (Ver. 1.0.162) to:

 Fix an error in which operations done by Spheroid and Spherical Centroid were using the
centroids from only one of the features, and the edges to the other feature.

 Wrote a workaround for an ArcGIS bug that triggers a crash in rare instances, producing an
“Automation Error” message at line 456.
 Modified some functions to increase processing speed.
Tool updated November 18, 2012 (Ver. 1.0.217) to add option to save connection lines.

Tool updated April 9, 2016 (Ver. 1.0.218) to give information and instructions if it finds the extension is
not registered properly.

15