Mono-Component, Robotically Applied, Foam-In-Place PUR Material

FOAM-IN-PLACE
GASKETING
Mono-Component, Robotically Applied,
Foam-In-Place PUR Material
Saint-Gobain® Dynafoam® (member of the Norseal® product
range) is a mono-component foam in place gasketing and
cushioning material. It is foamed by mixing with Nitrogen
(less than 5ppm humidity) and cures by reacting with moisture,
creating low density thermoset, elastomeric, foamed gaskets.
This product range has been developed to seal out water, air
or dust as well as decouple the noise vibrations. Thanks to its APPLICATIONS
semi-closed cell structure, Dynafoam creates efficient water
seal with only 30% compression. This cell structure generates • Automotive:
soft and conformable gaskets avoiding thin walled plastic – HVAC filter housing
parts to distort when compressing the gasket. It shows a low
– Stop lights
water absorption and extremely tough skin, which prevent
the gasket from being torn under rough assembly conditions. – Door modules and door locks
– Timing belt covers
Thanks to its engineered viscosity and its mechanical – Plenum chambers
foaming, Dynafoam exhibits excellent thixotropic behavior • Home appliances
allowing 3-dimensional and upside-down applications.
• Electrical/Electronic
The desired gasket height can be achieved with or without a components
groove, allowing the maximum design flexibility for engineers.
• Audio speakers
Packaging
• Construction elements
Dynafoam products are packed in a multilayer aluminum bag
to prevent any leakage during transport and manipulation, as
well as protecting the material from the humidity:
• Dynafoam 512 in drums of 185 kg
• Dynafoam 7440 range in drums of 180 kg

Dynafoam Gasketing www.tapesolutions.saint-gobain.com
Dynafoam Range — Properties

Performance tests are run using standard test procedures. The values presented are typical values and should not be used for specification purposes.
Property Test Method Unit 512 7440 7440 Black 7440 FC

Density ASTM D1056 kg/m3 300 - 400 220 - 280 220 - 280 220 - 280
Hardness ASTM D2240 Shore OO 30 - 45 35 - 55 35 - 55 30 - 50
Force to compress (30%) ASTM D1667 N/cm 1.3 - 2.0 1.7 - 3.5 1.7 - 3.5 1.5 - 3.5
Deflection force
ASTM D1667 N/cm 1.0 - 1.5 1.5 - 2.5 1.5 - 3.0 1.2 - 2.5
(30% after 1 minute)
Strength at break DIN 53571 N/cm2 20 - 35 > 20 > 20 > 20
Elongation at break DIN 53571 % > 100 > 100 > 100 > 100
Water absorption ASTM D1056 % < 15 < 10 < 10 < 10
Compression set
ASTM D1667 % < 20 < 15 < 15 < 15
(25% - 70°C)
Height : Width ratio - - 0.9 0.7 0.7 0.7
Maximum height - mm 10 7 7 7
Color* - - Dark Grey Grey Black Light Grey
Temperature range - °C Continuous: -40 to 70 / Intermittent: +120
*Color may slightly vary from lot to lot, without affecting product performance.
Important Instructions
Because Saint-Gobain cannot anticipate or control every potential application, we strongly recommend testing of
this product under individual application conditions prior to commercial use. Our labs can support in prototyping.
Shelf Life
Dynafoam 7440 and 7440 Black have a shelf life of 12 months from date of production, under the following storage
conditions: room temperature ≤ 25°C, under shelter (i.e. without direct exposure to sunshine & light).
Dynafoam 512 and 7440 FC have a shelf life of 6 months from date of production, under the following storage
conditions: room temperature ≤ 25°C, under shelter (i.e. without direct exposure to sunshine & light).
Dynafoam 512 and 7440 FC have a shelf life of 12 months from date of production, under the following storage
conditions: transported in refrigerated containers and refrigerated land transport, storage temperature of ≤ 15°C,
under shelter (i.e. without any direct exposure to sunshine & light).
Before use it is recommended to condition the Dynafoam drum for at least 24 hours at room temperature, to
optimize the viscosity for pumping.
IMPORTANT: It is the user’s responsibility to ensure the suitability and safety of Saint-Gobain products for all intended uses
and that the materials to be used comply with all applicable regulatory requirements. Saint-Gobain assumes no responsibility
for any product failures that occur due to misuse of the materials it provides arising out of the design, fabrication or
application of the products into which the materials are incorporated.
Saint-Gobain Tape Solutions WARRANTY: For a period of 6 months, Saint-Gobain warrants this product(s) to be free from defects in manufacturing.
The only obligation under any applicable product warranty will be to replace any portion proving defective, or at our
North America | South America | Europe | Asia option, to refund the purchase price thereof. SAINT-GOBAIN DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY
For a full list of locations, please visit AND FITNESS FOR A PARTICULAR PURPOSE.
tapesolutions.saint-gobain.com/contact-us Form #1002 | © Saint-Gobain March 2019 | Dynafoam, Norseal and Saint-Gobain are trademarks of Saint-Gobain.

Mono-Component, Robotically Applied, Foam-In-Place PUR Material

Uploaded by

Copyright:

Available Formats

Mono-Component, Robotically Applied, Foam-In-Place PUR Material

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Mono-Component, Robotically Applied, Foam-In-Place PUR Material

Uploaded by

Copyright:

Available Formats

FOAM-IN-PLACE

• Dynafoam 512 in drums of 185 kg

• Dynafoam 7440 range in drums of 180 kg

Dynafoam Range — Properties

Property Test Method Unit 512 7440 7440 Black 7440 FC

You might also like