Pipistrel Sinus 503 Operating Manual

Service and Repair Manual
applies to Sinus 503, Sinus 582 and Sinus 912

equipped with Rotax 503, Rotax 582
and Rotax 912 engines
(all TW and NW versions)
and
Virus 912 equipped with Rotax 912 engine
(all TW in NW versions)
Revision 1
updated 18th June, 2012
This is the original manual of Pipistrel d.o.o. Ajdovščina

Should third-party translations to other languages contain any inconsistencies,
Pipistrel d.o.o. Ajdovščina denies all responsibility.
Downloaded from www.Manualslib.com manuals search engine

2 Service manual pipistrel.si
Index of revisions
Enter and sign the list of revised pages in the manual into the spaces provided below. All revised pages
should be clearly designated in the upper right corner of the page, also, any changes in page content
should be clearly visible (e.g. marked with a bold vertical line)
Name of Revision no.

Signature, date Description
revision date
1, 18th June Tomazic, Coates Checked all spelling in document
Revision 1
2012 18th June 2012 US English

pipistrel.si Service manual 3
List of valid pages

This manual contains 74 original and revised pages listed below.
Pages State
Cover 1 Original
Index of revised pages 2 Original
List of valid pages 3 Original
Table of contents 5 Original
General 7-9 Original
Servicing the aircraft 11 - 27 Original
Schematics 29 - 52 Original
Repairs 53 - 70 Original
Caution:
This manual is valid only if it contains all of the original and revised pages listed above.
Each page to be revised must be removed, shredded and later replaced with the new, revised page in
the exact same place in the manual.

This page is intentionally left blank.

Table of contents
General
Servicing the aircraft
Schematics


General
General
Introduction
Notes and remarks
Materials used
in manufacturing process

General
Introduction
This manual contains all information needed for appropriate and safe servicing of Sinus ultralight
motorglider models 503, 582, 912 and Virus 912.
In case of aircraft damage or people injury resulting form disobeying instructions in the manual
PIPISTREL d.o.o. denies any responsibility.
All text, design, layout and graphics are owned by PIPISTREL d.o.o. Therefore this manual and any of
its contents may not be copied or distributed in any manner (electronic, web or printed) without the
prior consent of PIPISTREL d.o.o.
IT IS MANDATORY TO CAREFULLY STUDY THIS MANUAL PRIOR TO USE

OF AIRCRAFT
Notes and remarks

Safety definitions used in the manual:
WARNING! DISREGARDING THE FOLLOWING INSTRUCTIONS LEADS TO SEVERE

DETERIORATION OF FLIGHT SAFETY AND HAZARDOUS SITUATIONS, INCLUDING SUCH
RESULTING IN INJURY AND LOSS OF LIFE.
CAUTION! DISREGARDING THE FOLLOWING INSTRUCTIONS LEADS TO SERIOUS

DETERIORATION OF FLIGHT SAFETY.

General
Materials used in manufacturing process
Composite parts are made of:

fabric: GG160, GG200, 90070, 92110, 92120, 91125, 92140, 92145, KHW200
roving: NF24
foam: 75 kg/m3 PVC 3mm, PVC 5 mm, PVC 8mm
GFK: 3 mm, 5 mm, 7 mm of thickness
paint: gelcoat
heat resistant protection glass-aluminium sandwich
Metal parts used are:

tubes: materials: Fe0146, Fe 0147, Fe0545, Fe1430, AC 100, CR41 in LN9369
sheet metal: materials: Fe0147 in Al 3571
rods: materials: Fe 1221, Fe 4732, Č4130, Al 6082, CR41 in Al 6362
cable: AISI 316
bolts and nuts: 8/8 steel
All composite parts are made of glass, carbon and kevlar fiber manufactured by Interglas GmbH.
All parts have been tested at safety factor 1.8, meaning stressed to 7,2 G
All parts are made in moulds, therefore no shape or structural differences

can occur.
All designing, manufacturing and testing complies with following regulations:

• Bauvorschriften für Ultraleichtflugzeuge des Deutschen Aero Club e.V. Beauftragter des
Bundes-ministeriums für Verkehr
• JAR-1 microlight definition
• EASA CS-22 - certain sections
• EASA CS-VLA -certain sections
for Slovenian market also: Pravilnik o ultralahkih napravah Republike Slovenije.
All parts and materials presented in all versions of Sinus ultralight motorglider and
Virus 912 are also being used in glider and general aviation industry and all comply
with aviation standards.
WARNING! WHEN SERVICING OR REPLACING PARTS ALWAYS USE THE SAME

MATERIAL AS USED ORIGINALLY (SEE ABOVE).

General


Introduction
Repairs and
spare part replacements
Inspection periods
Special check-ups
Fibre reinforced plastic

repairs
Example of flaperon FRP

repair
Example of wing FRP

repair
Weight and Balance

Introduction
This chapter determines handling and (preventative) maintenance terms. Also, recommended
ground handling is presented.
Repairs, spare part replacements and

preventative maintenance
All major repairs and spare part replacements MUST be done by
authorised service personnel.
However, you are encouraged to take care of preventative maintenance yourself. This includes:
tire and wheel bearings replacements, safety wire replacements, door and safety harness
replacement, light bulb replacements, fuel hose replacements, battery servicing and
replacement, sparks and spark plugs replacements and air filter replacements.
The table below indicates recommended maintenance periods (see Service manual for detailed in-
formation).
Table legend:
C Check-up - visual only, check for free play and whether everything is in position - DO IT YOURSELF
CL Cleaning - DO IT YOURSELF
LO Lubricating, oiling - lubricate all designated parts and spots using proper lubricant -
DO IT YOURSELF
R Replacement - replace designated parts regardless of state and condition.
You are encouraged to DO undemanding replacements YOURSELF, otherwise have replacements
done by AUTHORISED SERVICE PERSONNEL
SC Special check-up - measuring, verifying tolerances and functionality - DONE BY AUTHORISED
SERVICE PERSONNEL ONLY
O Overhaul
first 5 50 100 200 500 1.000 10.000

daily
hours hours hours hours hours hours hours
WING AND TAIL SURFACES SC O
surface and structure condition C SC
deflections without free play C SC
bearings - moving parts’ bushings C SC
lights C
self-adhesive sealing tape C C SC
horizontal tail mount C C SC
drain holes CL

fist 5 50 100 200 500 1.000 10.000

daily
FUSELAGE SC O
surface and structure condition C SC
elevator control tube bearing C SC
undercarriage struts attaching points C C SC
doors, hinges C C SC LO
rudder control wires and hinges C C SC
CABIN SC O
control levers, instr. panel, seats C SC
control levers’ free play C C SC
instruments and pitot-static C check yearly
glass surfaces: clean, attached C C SC
rivet condition C SC
safety harnesses and attach. points C SC
parachute rescue sys. activation handle C SC
wing connectors: fuel, electrical C C SC
bolts and spar pins C C SC
wing main bushings, control connectors SC
UNDERCARRIAGE O
tires C replace on condition or every 5 years
main strut, tail /nose wh. strut condition C C SC
wheel axis and wheels C
hyd. brake lines C SC R
brake fluid C SC R (500 hrs or 5 years)
brake discs SC (R on condition)
wheel bearings C SC R
tail wheel main bolt C R
wheel fairings C C C
tail wheel mounting bolt C SC
CONTROLS (LO every 200 hrs or yearly) R

general free play C C SC
control stick C LO SC
rudder pedals (damage, centered, paral.) C C C
rudder wire rope C SC
bolts, visible bearings (tail, fuselage) SC
difficult-to-reach bearings (wings, under cabin floor) LO+SC
aileron, elevator and rudder hinges SC
equal spoiler extension, undistributed m. C SC LO+SC
spoiler plate springs stiffness C LO
flap handle C SC
elevator trim C R cable every 500 hrs
springs: flaps, rudder, el. trim, stabilizer main fastening bolt LO C R
spoilers’ (airbrakes’) drive fine adjustment see page 15 for detailed description

first 5 50 100 200 500 1.000 10.000
daily
ENGINE
see enclosed Rotax engine manual for detailed engine maintenance information.
In addition to Rotax manual:
two-stroke engines (overhaul every 300 hours) C
four-stroke engines (overhaul every 1,500 hours) from engine serial number 4404718
engine cover screws C C C
engine mount C C SC
engine mount dumpers and other R every 500 hrs
C SC
rubber parts or every 5 years
air filters C C CL SC
elect. terminals, joints and
C C SC
connectors, hoses, radiator mount
exhaust muffler C C SC SC
exhaust pipe springs and fire protect. C C SC R
throttle, choke, propeller wire drive SC R
ENGINE CONTROL O
choke and throttle lever wire ropes C C SC R
levers C SC
PROPELLER AND SPINNER SC O

surface condition C
fastening bolts R
propeller bushings R
propeller pitch C SC
propeller balance C SC
FUEL SYSTEM O every 1000 hrs or 5 years

general leakage C C SC
water inside gascolator C
dirt and gascolator filter CL CL CL R
wing fuel tank caps C
fuel tank caps o-ring R every 500 hrs or 5 years
fuel valves and leakage C
ELECTRICAL WIRING SC R
battery C C SC
battery fluids C C SC
instr.panel wires and connectors C C
NAV, AC and LDG lights C C
fuses C C

first 5 50 100 200 500 1.000 10.000
daily
OIL AND WATER LINES O every 500 hrs or 5 years
oil and cooling fluids level C C
oil and cooling fluids leakage C C
four stroke engine oil (and engine
refer to engine manual
filter) first 25 hours +
cooling fluid (level) refer to engine manual
hoses C C R
radiators C C
water radiator pressure cap refer to engine manual
PITOT-STATIC LINING SC O
instrument to pitot tube lining C C
instrument setting C C
pitot tube condition (clean, firmly att.) C C
whole pitot-static lining C C
Spoilers’ (airbrakes’) drive fine adjustment

CAUTION! Perform this operation only once after first 50 flight hours! Check spoilers
thoroughly for unobstructed, smooth and even extension every 200 flight hours!
Schematic of spoilers’ (airbrakes’) drive fine adjustment

(see next page for detailed description)
5 4
3 4

Perform the adjustment as follows:
1 Unscrew and remove the inner horizontal bolt of the airbrake’s plate. Do not lose any parts!
2 Lift the airbrake in order to make room for further operation.
3 Unscrew and remove the bolt attaching the rod-end bearing to the airbrake’s plate lever.
Do not lose any parts!
4 Rotate the rod-end bearing fine-setting nut 360° so that the rod end moves towards the
other end of the airbrake’s box (length of rod increases). Make sure you secure this nut
after turning it for 360°!
5 Grease the drive around the rubber sleeve inside the airbrake’s box using rubber-non-
agressive lubricant spray.
Once you have accomplished this, repeat steps 1-3 in opposite order (3,2,1). Make sure you apply ad-
hesive (e.g. Loctite) on all screws when reattaching!
Perform the procedure at the other airbrake as well. In the end verify airbrakes for equal extension.
WARNING! Should the airbrakes not retract evenly, apply step action 4 again for the air-
brake, which remains higher when retracting.
Vital stages of spoilers’ (airbrakes’) drive fine adjustment in pictures
Spoiler’s (Airbrake’s) plate Horizontal bolt of the AB’s plate
1 1
Rod-end bearing
3
4

Clicking noise overhead

The wings are factory fitted to the fuselage to make a tight fit at approximately 20° Celsius. When ex-
posed to low temperatures, materials shrink. Therefore, flying in the winter or in cold temperatures,
you may encounter “click-clack” like noises above your head. The remedy for this unpleasant noises
is to add washers, typically of 0,5 mm thickness in-between wing and fuselage. Washers must be
added both at rear and front bushings at one side of the fuselage only!
WARNING! It is mandatory to consult the manufacturer or authorised service personnel

before applying washers!
Adjustment of tail wheel steering clutch stiffness

To adjust the stiffness of tail wheel steering clutch you need two allen keys (a.k.a. hex-wrench, inbus-
key). On top of the wheel fork you will notice a ring with two tubes welded to each side with hex-
bolts inside. First disconnect the springs at the tubes, then stick an allen key into each of these tubes
and tighten or loosen the screw inside. Make sure, tightening or loosing, you apply equal number of
screw rotations at both sides. To check if the steering clutch is stiff enough, lift the tail and rotate the
fork left and right. At the end, reattach both springs to the tubes again.
(see Service manual for photos)
Venting the hydraulic brakes’ lining

In case you notice poor braking action even when hydraulic brake levers are depressed fully, it is
most definitely necessary to vent the hydraulic lining. To do so, first unscrew the caps of small fluid
reservoirs (behind rudder pedals on one side of the cockpit) and remove the inner seal cap.
At the side where there are no fluid reservoirs grab the whole rudder pedal and deflect it back fully,
so that it becomes level with the cockpit’s floor beneath. Now, at the side where there are fluid res-
ervoirs, jerk brake levers back and forth a couple of times - this will push air bubbles towards the
reservoir and out of the lining. When convinced air bubbles are no more, put seal caps back onto the
reservoirs and screw the caps on as well. Repeat the procedure for the other brake lever.
WARNING! Should you encounter any difficulties during this procedure or the air bubbles
would not vent, please consult the manufacturer or authorised service personnel for further
instructions.

Schematic of hydraulic brakes’ lining
Poor braking action

In case you notice poor braking action even when hydraulic brake levers are depressed fully, it is not
necessary the air bubbles in the hydraulic lining, which is causing the problem.
The main wheel’s main axis’ nut (especially after a wheel and/or axis replacement nut) may be tight-
ened incorrectly so that the brake shims do not make contact with the brake plate. Please consult
the manufacturer or authorised service personnel for further information.
Schematic of wheel and wheel brakes

Connecting Auxiliary power supplies

Should you be unable to start the engine due to a weak battery, auxiliary power supplies can be con-
nected to help starting the engine.
Battery’s & Relay’s location Battery (black) & Relay (top-right)
Top-left nipple (c. positive (+) wire here) Exhaust (connect negative (-) wire here)
To connect an auxiliary power supply use battery connector cables with clamps at either ends.
Connect the negative (-) wire to aircraft’s exhaust (sticking out below the engine cowlings).
The positive (+) wire leads inside the cockpit to the relay mounted top-right of the aircraft’s battery
on the firewall. This relay has 3 nipples; the positive (+) wire must be connected to the upper-left
nipple, the only one to which 2 cables are connected to.
After you have connected the wires correctly, start the engine normally by pressing the starter but-
ton in the cockpit.
WARNING! The pilot must be in cockpit when starting the engine. The person who will
disconnect the cables after the engine has started must be aware of the danger of spinning
propeller nearby.

Fibre reinforced plastic repairs

WARNING! Do not, under any circumstances attempt to repair damages greater than 50 mm
in size (on wing) and/or 20 mm in size on any control circumstances. These require a treatment by
a FRP professional!
Definition of minor damage

Only the damage listed below can be considered as minor damage repairable by oneself.
Any damage limited to gelcoat or filler.

Holes in the fuselage underside where the average diameter does not exceed:
Forward fuselage: 50 mm
Rear fuselage: 50 mm
Cracks in fuselage underside max.
Forward fuselage: 50 mm
Rear fuselage: 50 mm
The fuselage glued joint (rear fuselage) should not be damaged.
Holes, cracks and tears, bubbles etc. in the wings, horizontal stabilizer and control surfaces skins
where the damage does not exceed (average diameter crack length):
Wings: 50 mm (50 mm)

Horizontal stabilizer: 20 mm (20 mm)
Rudder: 20 mm (20 mm)
Flaperon, Elevator: 20 mm (20 mm)
The above parts should not be damaged in the spar area.

Damaged fittings should not be repaired but replaced.
Facilities
To insure proper curing, the room temperature during repair work and at least 12 hours afterwards
should be maintained at 21°C (70° F). After that the repaired parts are to be tempered. Therefore you
may construct a tempering tent, using plastic film or Styrofoam plates.
Filler
For gluing, the resin-hardener mix should be thickened with chopped cotton fibres FL l f. (add
enough so that the resin no longer flows). The surfaces to be glued should be wetted with non-thick-
ened resin & hardener before.
To glue foam pieces into place when repairing sandwich sections and to fill in irregularities and
gaps etc. around the repair, Microballoons BJO - 0930 can be used mixed with the resin-hardener.
Application and mixing is the same as for the cotton flocks.
WARNING! Only materials listed on page 9 should be used. Only damage defined above
should be repaired.

Repair method for FRP

Cut out damaged area, roughen the surrounding area for the overlap required. Repairs should be
made such that bonding is wet over dry. Specific details concerning handling and using fibre rein-
forced plastics can be obtained from various publications ie. “Petite Plane Patch Primer.”
The use of Carbon fibre is the same as for glassfibre, except that the carbon fibres should not be
kinked and only the specified resins are used.
WARNING! All repairs should be tempered for 20 hours at 54°C before the next take off.
Repairs of the FRP shell

Prepare the repair area as specified above. Scarf the shell so that the individual layers of fabric can be
seen like plywood layers. Remove the gelcoat for at least 20 mm around the damaged area.
Repairing the outer skin of a sandwich panel

Cut out the damaged area, remove the gelcoat over the overlap area and 10 mm around the dam-
aged area. Fill the damaged foam area with resin thickened with microballoons (microballoons-res-
in), let harden. Sand down. With a round headed hammer tap the outer skin around the hole so that
the foam is somewhat compressed, therefore heat this area to ca. 60°C (140°F). Apply the new cloth.
Repair of outer and inner skin of a sandwich panel

Additionally remove as much foam as is needed so that the entire damage to the inner skin can be
seen plus enough undamaged inner skin as is required for overlapping. If the inner skin still holds
together, sand properly and lay up the new cloth over it. Insert a suitable cut piece of foam, 1-2 mm
thinner than the original, glued in with microballoons-resin. Should the inner skin be so damaged
that the above process cannot be use the inner skin fabric should be applied to the foam first and
left to harden before inserting into the repair area. Microballoons-resin should once again be used.
For lay up of the fabric to the foam, a layer of microballoons-resin should be applied first to eliminate
the formation of air bubbles. Apply outer layers
Special hints for processing aramid fibres

The difficulties processing aramid fibre starts already when cutting the fabric. Only with very sharp
tools (toothed scissors) cutting the material is possible. Sanding the fibres is not possible without
formation of fluff or fuzz. Only wet sanding is feasible. After sanding, the area must be dried with a
fan heater.
Aramid fibre has the tendency to take up humidity. Therefore dry storage and drying the fibres prior
to processing is necessary. Aramid must be protected against UV-rays before and after processing.
An aramid repaired area must be protected by a paint with UV-protection. Thin aramid layers can’t
be scarfed. Only overlapping is possible.
Repair of the carbon fibre - aramid fibre – hybrid fuselage shell

With this construction the repair method see mentioned above is not applicable. Contact the manu-
facturer.

Repairing small dents in a sandwich panel skin

(no cracks in the gelcoat)
Small dents can usually be removed by heating up to 60° to 70° C (140° -158°F). Use a hot air blower
to heat the area of the dent. The crushed foam will then spring back to its original form, so that the
dent will hardly be seen. Final sanding with wet sandpaper grade 600 should finish the job. In more
severe cases, one coat of gelcoat will remove all trace of the dent.
Outer skin finish

Repairs should be such that the area is exactly level or only slightly higher than the surrounding skin
surfaces. Sand the hardened repair surface with dry grade 80 sandpaper. Fill with Polyester filler, let
dry and sand with dry sandpaper. When the surface is smooth, sand the repair area and at least 5 cm
(2 in.) of the surrounding gelcoat with wet sandpaper grade 400. Spray the repair area with 5 coats of
gelcoat.
After the gelcoat has hardened, sand with grade 400, 600 and 800 wet sandpaper until the surface is
smooth. Polish with a power buffer (electric drill or similar with cloth polishing wheel). Apply a block
of wax onto the rotating polishing wheel and then polish the repaired area. Do not polish in only
one direction, and do not polish one spot for too long to prevent material overheating.
WARNING! After repairing control surfaces, the mass balance weights MUST be checked
again with the values given in the maintenance manual. Should the maximum values be exceed-
ed, then the parts have to be replaced.

Example of flaperon FRP repair

a FRP professional!
Phase I
Carefully cut and remove the damaged foam (Herex 3
mm) in width of at least 20 mm around the damaged
area.
Clean the area, paying special attention that the inner
fabric is immaculate. This is of vital importance. After
you have cleaned and rinsed everything, laminate the
20 mm area according to the laminate-plan shown on
the drawing below.
Laminate plan for flaperon
WARNING! if the damage area is located on the flap hinge (the fabric used there is carbon
fibre - black color) you must laminate using one ply of GG160 fabric, oriented diagonally to the
flight direction. Also, you must apply Peel Ply on top of GG160.

Phase II
Remove the Peel Ply and adapt a new piece of foam (Herex 3 mm) as accurately as you possibly can
and glue it with microballoons.
WARNING! Do not apply too much pressure anywhere!
Phase III
Grind the foam if its level is too high. Also grind the external laminate around the cut-out for about
25 mm in a conical-shape (see next drawing). When done, laminate as follows:
- Place one (1) piece of GG160 diagonally and
- One (1) piece of 90070 perpendicular to the flight direction.
Phase IV
Grind only the outer edge of the new fabric. When done, the new surface is ready to be painted.

Drawing of skin final repair

Example of wing FRP repair

a FRP professional!
Phase I
Preparing the surface. Carefully clean the damaged foam and check if there is also a damage on the
inner fabric.
If the inner fabric in not damaged fill the hole with microballoons as you can see on the drawing be-
low. In case the hole is through the inner fabric as well, you have to repair the inner fabric, too.
The new patch must be at least 20mm bigger than the damaged area. You also have to replace (glue)
the missing foam with a new one.
Gap filling drawing

Phase II
Laminating. Grind the outer fabric in a shape of a cone at least 25mm around the damaged area (see
drawing below) and laminate only the ground surface with fabrics as follows:
- Two (2) pieces of 92110 and
- One (1) piece of 90070
When laminating be careful about the orientation of the fibres. The fibres of 92110 must be put di-
agonally to the flight direction, the fibres of 90070 must be put perpendicular to this direction. The
directions are also shown in the drawing below.
Phase III
Grinding. You can grind only the surface (ring) around the damaged area. This surface is shawn in
previous drawing. When done the surface is ready for painting.

Weight and balance
Weight and Balance

This chapter provides information on aircraft’s weight and balance, which is essential for safe flying
activity.
Procedure
How to weigh the aircraft and later determine the CG correctly:
Make sure all listed aircraft parts and appliances are installed and in position.
Remove all other objects (e.g. tools, mops ...).
Empty fuel tanks except for the unusable fuel.
Fill up engine oil to the top marking.
Retract flaps and spoilers, leave control surfaces centred.
Support fuselage at the rear and level the aircraft inside a closed space.
To do this, use the provided airfoil template at lower side of the wing close to the wing root
and make sure its straight edge is level (horizontal).
Once leveled, read the scale readings and subtract eventual tare weight.
Now measure and record all readings and fill out the bottom schematic.
Datum is wing’s leading edge at wing root.
CG lever arm formula for Tail-wheel aircraft (Sinus TW, Virus TW, any model):
Lever arm of CG (X) = ((G2 / G) x b) + a
CG lever arm formula for Nose-wheel aircraft (Sinus NW, Virus NW, any model):
Lever arm of CG (X) = ((G1 / G) x c) - a
Weighing form (TAILWHEEL)

Weighing point and symbol Scale reading Tare Nett
right main wheel (GD)
left main wheel (GL)
tail wheel (G2)
total (G = GD + GL +G2)

Weight and balance
Determination of CG
Weight’s lever
Weight (kg) Torque (kg/cm) Remarks
arm (cm)
Basic cfg. empty weight
CAUTION! Each newly installed part or appliance must be registered in the upper table. Also,
new total weight and lever arm of CG values must be entered and position of CG re-determined.
Furthermore, the momentum must be recalculated. This is rather easy to do. First multiply the
new part’s weight by it’s lever arm measured from the reference point (wing’s trailing edge). Then
sum up all moments and divide the sum by the new total weight.
WARNING! Regard to the Flight manual and Maintenance manual for allowable C.G. limita-
tions!

Sample c.g. calculation
Guidelines
Gtotal is the total mass of empty aircraft. All calculations can be performed with aircraft empty
weight and empty weight centre of gravity (c.g.), as the pilots sits directly below the centre of gravity
and do not cause the c.g. to be shifted. The amount of fuel quantity also has no impact on the c.g..
WARNING! Both pilots’ weight and weight of fuel do not influence c.g. or their influence is
insignificant. However, baggage can influence the c.g. severely and may cause the aircraft to
become uncontrollable!
Basic CG formulas and calculation

The below instructions are valid for Virus Tail Wheel and Nose Wheel editions. Read thoroughly. Note
also that the basic c.g. at 287 mm will be used purely as an example.
First, weigh the aircraft according to the procedure described in this chapter and write down values
of G1 (sum of scale readings at main wheels) and G2 (scale reading at tail/front wheel). Then calcu-
late the position of c.g. in millimeters (mm) from the datum (wing’s leading edge at wing root).
For Tail wheel edition of Virus use the following formula:
G2 tail x b G2tail x 4300 mm

CGmm = +a= + 110mm = 287mm
Gtotal Gtotal
where:
G2tail is the scale reading at the tail wheel,
Gtotal is the sum of G1 and G2tail (G1+G2tail), a.k.a. aircraft empty weight
a is the distance from main wheel axis to wing’s leading edge,
b is the distance between main and tail wheel axis.
For Nose wheel edition of Virus use the following formula:
G1back x c G1back x 1525 mm

CGmm = -a= - 1020mm = 287mm
Gtotal Gtotal
where:
G2back is the sum of scale readings at both main (back) wheels,
Gtotal is the sum of G1 and G2back (G1+G2back), a.k.a. aircraft empty weight
a is the distance from nose wheel axis to wing’s leading edge,
b is the distance from main wheel axis to wing’s leading edge,
c = (a+b) is the sum of both distances above.
Second, determine the c.g. position in percentage (%) of Mean Aerodynamic Chord (MAC) with fol-
lowing the formula:
CGmm - R 287mm - 29mm

CG%MAC = x 100 = x 100 = 28.4%
MAC 908mm
where:
CGmm is the position of CG in millimeters (mm),
R is the difference between wing’s leading edge and MAC’s leading edge (29 mm),
MAC is the Mean Aerodynamic Chord (908 mm, for Sinus it is 869 mm).

Schematics
Control levers
Wings
Tail surfaces
Undercarriage
Brakes
Fuel system
Engine cooling system
Engine lubrication system
Throttle and choke drive
Electrical system

Schematics
INSPECTION PERIODS SYMBOLS

Control levers glue
50 100 250 500 1000
grease
ABBEREVIATIONS
UVM multi-purpuse grease oil

Flap handle, 1 243 Loctite 243
648 Loctite 648 hand insp.

Schematics
Flap handle, 2
glue
50 100 250 500 1000
grease
ABBEREVIATIONS

243 Loctite 243

Schematics

Control stick glue
50 100 250 500 1000
grease
ABBEREVIATIONS

243 Loctite 243

Schematics

Rudder pedals 100 250 500 1000
glue
50
grease
ABBEREVIATIONS

243 Loctite 243

Schematics

Flap levers glue
50 100 250 500 1000
grease
ABBEREVIATIONS

243 Loctite 243

Schematics

glue
Wings 50 100 250 500 1000
grease
ABBEREVIATIONS

wing’s exterior 243 Loctite 243

Schematics

wing’s interior glue
50 100 250 500 1000
grease
ABBEREVIATIONS

243 Loctite 243

Schematics

Airbrake - spoiler 100 250 500 1000
glue
50
grease
ABBEREVIATIONS

243 Loctite 243

Schematics

glue
Tail surfaces 50 100 250 500 1000
grease
ABBEREVIATIONS

horizontal tail surfaces 243 Loctite 243

Schematics

vertical tail surfaces 100 250 500 1000
glue
50
grease
ABBEREVIATIONS

243 Loctite 243

Schematics

glue
100 250 500 1000
Undercarriage 50
grease
ABBEREVIATIONS

tail wheel (Sinus, all models) 243 Loctite 243

Schematics

glue
Brakes 50 100 250 500 1000
grease
ABBEREVIATIONS

hydraulic brakes’ drive 243 Loctite 243

Schematics
Fuel system
Rotax 912 (no fuel return circuit)

Schematics
Fuel system
Rotax 912 (fuel return circuit)

pipistrel.si
Rotax 582
46 Service manual
Schematics

Schematics
Engine cooling system

Rotax 912

pipistrel.si
Rotax 582
48 Service manual
Schematics

Schematics
Engine lubrication system

Rotax 912

Schematics
Throttle and choke drive

Rotax 912

Service manual 51
Schematics
Rotax 582
pipistrel.si

Schematics
Electrical system
NAV lights & strobes

Schematics
electrical circuit


Schematics
Repairs
Elevator vertical pushrod replacement
VARIO Propeller Assembly
VARIO Propeller Drive Replacement
VARIO Propeller Bearing Replacement
3-Bladed Fixed Pitch Propeller
Airbrake Control’s Drive Reinforcement (1)
Airbrake Control’s Drive Reinforcement (2)
Flaperon Hinge Replacement
Flaperon Lateral Drive Assembly
Flaperon Mass Balance Weights Installation
Wheel Brake (cockpit side) Assembly
Hydraulic Fluid Lines Assembly (wheel side)
Airbrake Handle Assembly
Airbrake Guidance Installation
Venting the Hydraulic Brake Lines
Wheel Brake Repair
Nose Wheel Strut Assembly

Repairs
Elevator Vertical Pushrod Replacement

Repairs
VARIO Propeller Assembly

Repairs
VARIO Propeller Drive Replacement

Repairs
VARIO Propeller Bearing Replacement

Repairs
3-Bladed Fixed Pitch Propeller Assembly

Repairs
Airbrake Control’s Drive Reinforcement (part 1)

pipistrel.si
Wing Control’s Drive Reinforcement (part 2)
62 Service manual
Repairs

Repairs
Flaperon Hinge Reinforcement

Repairs
Flaperon Lateral Drive Assembly

Repairs
Flaperon Mass Balance Weights Installation

Repairs
Wheel Brake (cockpit side) Assembly

Service manual 67
Repairs Hydraulic Fluid Lines Assembly (wheel side)
pipistrel.si

Repairs
Airbrake Handle Assembly

Repairs
Airbrake Guidance Installation

Repairs
Venting the Hydraulic Brake Lines

Service manual 71
Repairs
Wheel Brake Repair

pipistrel.si

pipistrel.si
Nose Wheel Strut Assembly
72 Service manual
Repairs

Pipistrel d.o.o. Ajdovščina
podjetje za alternativno letalstvo
Goriška cesta 50a
5270 Ajdovščina
Slovenija
tel: +386 (0)5 3663 873

fax: +386 (0)5 3661 263
e-mail: info@pipistrel.si
www.pipistrel.si

Pipistrel Sinus 503 Operating Manual

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Pipistrel Sinus 503 Operating Manual

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Pipistrel Sinus 503 Operating Manual

Uploaded by

Copyright:

Available Formats

Service and Repair Manual

applies to Sinus 503, Sinus 582 and Sinus 912

This is the original manual of Pipistrel d.o.o. Ajdovščina

Downloaded from www.Manualslib.com manuals search engine

Name of Revision no.

Downloaded from www.Manualslib.com manuals search engine

List of valid pages

Downloaded from www.Manualslib.com manuals search engine

This page is intentionally left blank.

Downloaded from www.Manualslib.com manuals search engine

Servicing the aircraft

Downloaded from www.Manualslib.com manuals search engine

This page is intentionally left blank.

Downloaded from www.Manualslib.com manuals search engine

Notes and remarks

Downloaded from www.Manualslib.com manuals search engine

IT IS MANDATORY TO CAREFULLY STUDY THIS MANUAL PRIOR TO USE

Notes and remarks

WARNING! DISREGARDING THE FOLLOWING INSTRUCTIONS LEADS TO SEVERE

CAUTION! DISREGARDING THE FOLLOWING INSTRUCTIONS LEADS TO SERIOUS

Downloaded from www.Manualslib.com manuals search engine

Materials used in manufacturing process

Composite parts are made of:

Metal parts used are:

All parts are made in moulds, therefore no shape or structural differences

All designing, manufacturing and testing complies with following regulations:

WARNING! WHEN SERVICING OR REPLACING PARTS ALWAYS USE THE SAME

Downloaded from www.Manualslib.com manuals search engine

This page is intentionally left blank.

Downloaded from www.Manualslib.com manuals search engine

Servicing the aircraft

Fibre reinforced plastic

Example of flaperon FRP

Example of wing FRP

Weight and Balance

Downloaded from www.Manualslib.com manuals search engine

Repairs, spare part replacements and

first 5 50 100 200 500 1.000 10.000

Downloaded from www.Manualslib.com manuals search engine

fist 5 50 100 200 500 1.000 10.000

CONTROLS (LO every 200 hrs or yearly) R

Downloaded from www.Manualslib.com manuals search engine

PROPELLER AND SPINNER SC O

FUEL SYSTEM O every 1000 hrs or 5 years

Downloaded from www.Manualslib.com manuals search engine

Spoilers’ (airbrakes’) drive fine adjustment

Schematic of spoilers’ (airbrakes’) drive fine adjustment

Downloaded from www.Manualslib.com manuals search engine

Perform the adjustment as follows:

2 Lift the airbrake in order to make room for further operation.

Vital stages of spoilers’ (airbrakes’) drive fine adjustment in pictures

Spoiler’s (Airbrake’s) plate Horizontal bolt of the AB’s plate

Downloaded from www.Manualslib.com manuals search engine

Clicking noise overhead

WARNING! It is mandatory to consult the manufacturer or authorised service personnel

Adjustment of tail wheel steering clutch stiffness

Venting the hydraulic brakes’ lining