347

METHOD 4 - DETERMINATION OF MOISTURE CONTENT

IN STACK GASES

NOTE: This method does not include all the

specifications (e.g., equipment and supplies) and procedures

(e.g., sampling) essential to its performance. Some

material is incorporated by reference from other methods in

this part. Therefore, to obtain reliable results, persons

using this method should have a thorough knowledge of at

least the following additional test methods: Method 1,

Method 5, and Method 6.

1.0 Scope and Application.

1.1 Analytes.

Analyte CAS No. Sensitivity

Water vapor (H2O) 7732-18-5 N/A

1.2 Applicability. This method is applicable for the

determination of the moisture content of stack gas.

1.3 Data Quality Objectives. Adherence to the

requirements of this method will enhance the quality of the

data obtained from air pollutant sampling methods.

2.0 Summary of Method.

2.1 A gas sample is extracted at a constant rate from

the source; moisture is removed from the sample stream and

determined either volumetrically or gravimetrically.

 348

2.2 The method contains two possible procedures: a

reference method and an approximation method.

2.2.1 The reference method is used for accurate

determinations of moisture content (such as are needed to

calculate emission data). The approximation method,

provides estimates of percent moisture to aid in setting

isokinetic sampling rates prior to a pollutant emission

measurement run. The approximation method described herein

is only a suggested approach; alternative means for

approximating the moisture content (e.g., drying tubes, wet

bulb-dry bulb techniques, condensation techniques,

stoichiometric calculations, previous experience, etc.) are

also acceptable.

2.2.2 The reference method is often conducted

simultaneously with a pollutant emission measurement run.

When it is, calculation of percent isokinetic, pollutant

emission rate, etc., for the run shall be based upon the

results of the reference method or its equivalent. These

calculations shall not be based upon the results of the

approximation method, unless the approximation method is

shown, to the satisfaction of the Administrator, to be

capable of yielding results within one percent H2O of the

reference method.

3.0 Definitions. [Reserved]

 349

4.0 Interferences.

4.1 The moisture content of saturated gas streams or

streams that contain water droplets, as measured by the

reference method, may be positively biased. Therefore, when

these conditions exist or are suspected, a second

determination of the moisture content shall be made

simultaneously with the reference method, as follows:

Assume that the gas stream is saturated. Attach a

temperature sensor [capable of measuring to ±1 EC (2 EF)] to

the reference method probe. Measure the stack gas

temperature at each traverse point (see Section 8.1.1.1)

during the reference method traverse, and calculate the

average stack gas temperature. Next, determine the moisture

percentage, either by: (1) using a psychrometric chart and

making appropriate corrections if the stack pressure is

different from that of the chart, or (2) using saturation

vapor pressure tables. In cases where the psychrometric

chart or the saturation vapor pressure tables are not

applicable (based on evaluation of the process), alternative

methods, subject to the approval of the Administrator, shall

be used.

5.0 Safety.

5.1 Disclaimer. This method may involve hazardous

materials, operations, and equipment. This test method may

 350

not address all of the safety problems associated with its

use. It is the responsibility of the user of this test

method to establish appropriate safety and health practices

and determine the applicability of regulatory limitations

prior to performing this test method.

6.0 Equipment and Supplies.

6.1 Reference Method. A schematic of the sampling

train used in this reference method is shown in Figure 4-1.

6.1.1 Probe. Stainless steel or glass tubing,

sufficiently heated to prevent water condensation, and

equipped with a filter, either in-stack (e.g., a plug of

glass wool inserted into the end of the probe) or heated

out-of-stack (e.g., as described in Method 5), to remove

particulate matter. When stack conditions permit, other

metals or plastic tubing may be used for the probe, subject

to the approval of the Administrator.

6.1.2 Condenser. Same as Method 5, Section 6.1.1.8.

6.1.3 Cooling System. An ice bath container, crushed

ice, and water (or equivalent), to aid in condensing

moisture.

6.1.4 Metering System. Same as in Method 5, Section

6.1.1.9, except do not use sampling systems designed for

flow rates higher than 0.0283 m3/min (1.0 cfm). Other

metering systems, capable of maintaining a constant sampling

 351

rate to within 10 percent and determining sample gas volume

to within 2 percent, may be used, subject to the approval of

the Administrator.

6.1.5 Barometer and Graduated Cylinder and/or

Balance. Same as Method 5, Sections 6.1.2 and 6.2.5,

respectively.

6.2. Approximation Method. A schematic of the

sampling train used in this approximation method is shown in

Figure 4-2.

6.2.1 Probe. Same as Section 6.1.1.

6.2.2 Condenser. Two midget impingers, each with 30-

ml capacity, or equivalent.

6.2.3 Cooling System. Ice bath container, crushed

ice, and water, to aid in condensing moisture in impingers.

6.2.4 Drying Tube. Tube packed with new or

regenerated 6- to 16-mesh indicating-type silica gel (or

equivalent desiccant), to dry the sample gas and to protect

the meter and pump.

6.2.5 Valve. Needle valve, to regulate the sample

gas flow rate.

6.2.6 Pump. Leak-free, diaphragm type, or

equivalent, to pull the gas sample through the train.

6.2.7 Volume Meter. Dry gas meter, sufficiently

accurate to measure the sample volume to within 2 percent,

 352

and calibrated over the range of flow rates and conditions

actually encountered during sampling.

6.2.8 Rate Meter. Rotameter, or equivalent, to

measure the flow range from 0 to 3 liters/min (0 to 0.11

cfm).

6.2.9 Graduated Cylinder. 25-ml.

6.2.10 Barometer. Same as Method 5, Section 6.1.2.

6.2.11 Vacuum Gauge. At least 760-mm (30-in.) Hg

gauge, to be used for the sampling leak check.

7.0 Reagents and Standards. [Reserved]

8.0 Sample Collection, Preservation, Transport, and

Storage.

8.1 Reference Method. The following procedure is

intended for a condenser system (such as the impinger system

described in Section 6.1.1.8 of Method 5) incorporating

volumetric analysis to measure the condensed moisture, and

silica gel and gravimetric analysis to measure the moisture

leaving the condenser.

8.1.1 Preliminary Determinations.

8.1.1.1 Unless otherwise specified by the

Administrator, a minimum of eight traverse points shall be

used for circular stacks having diameters less than 0.61 m

(24 in.), a minimum of nine points shall be used for

rectangular stacks having equivalent diameters less than

 353

0.61 m (24 in.), and a minimum of twelve traverse points

shall be used in all other cases. The traverse points shall

be located according to Method 1. The use of fewer points

is subject to the approval of the Administrator. Select a

suitable probe and probe length such that all traverse

points can be sampled. Consider sampling from opposite

sides of the stack (four total sampling ports) for large

stacks, to permit use of shorter probe lengths. Mark the

probe with heat resistant tape or by some other method to

denote the proper distance into the stack or duct for each

sampling point.

8.1.1.2 Select a total sampling time such that a

minimum total gas volume of 0.60 scm (21 scf) will be

collected, at a rate no greater than 0.021 m3/min

(0.75 cfm). When both moisture content and pollutant

emission rate are to be determined, the moisture

determination shall be simultaneous with, and for the same

total length of time as, the pollutant emission rate run,

unless otherwise specified in an applicable subpart of the

standards.

8.1.2 Preparation of Sampling Train.

8.1.2.1 Place known volumes of water in the first two

impingers; alternatively, transfer water into the first two

impingers and record the weight of each impinger (plus

water) to the nearest 0.5 g. Weigh and record the weight of

 354

the silica gel to the nearest 0.5 g, and transfer the silica

gel to the fourth impinger; alternatively, the silica gel

may first be transferred to the impinger, and the weight of

the silica gel plus impinger recorded.

8.1.2.2 Set up the sampling train as shown in Figure

4-1. Turn on the probe heater and (if applicable) the

filter heating system to temperatures of approximately

120 EC (248 EF), to prevent water condensation ahead of the

condenser. Allow time for the temperatures to stabilize.

Place crushed ice and water in the ice bath container.

8.1.3 Leak Check Procedures. It is recommended, but

not required, that the volume metering system and sampling

train be leak-checked as follows:

8.1.3.1 Metering System. Same as Method 5, Section

8.4.1.

8.1.3.2 Sampling Train. Disconnect the probe from

the first impinger or (if applicable) from the filter

holder. Plug the inlet to the first impinger (or filter

holder), and pull a 380 mm (15 in.) Hg vacuum. A lower

vacuum may be used, provided that it is not exceeded during

the test. A leakage rate in excess of 4 percent of the

average sampling rate or 0.00057 m3/min (0.020 cfm),

whichever is less, is unacceptable. Following the leak

check, reconnect the probe to the sampling train.

 355

8.1.4 Sampling Train Operation. During the sampling

run, maintain a sampling rate within 10 percent of constant

rate, or as specified by the Administrator. For each run,

record the data required on a data sheet similar to that

shown in Figure 4-3. Be sure to record the dry gas meter

reading at the beginning and end of each sampling time

increment and whenever sampling is halted. Take other

appropriate readings at each sample point at least once

during each time increment.

NOTE: When Method 4 is used concurrently with an

isokinetic method (e.g., Method 5) the sampling rate should

be maintained at isokinetic conditions rather than 10

percent of constant rate.

8.1.4.1 To begin sampling, position the probe tip at

the first traverse point. Immediately start the pump, and

adjust the flow to the desired rate. Traverse the cross

section, sampling at each traverse point for an equal length

of time. Add more ice and, if necessary, salt to maintain a

temperature of less than 20 EC (68 EF) at the silica gel

outlet.

8.1.4.2 After collecting the sample, disconnect the

probe from the first impinger (or from the filter holder),

and conduct a leak check (mandatory) of the sampling train

as described in Section 8.1.3.2. Record the leak rate. If

 356

the leakage rate exceeds the allowable rate, either reject

the test results or correct the sample volume as in Section

12.3 of Method 5.

8.2 Approximation Method.

NOTE: The approximation method described below is

presented only as a suggested method (see Section 2.0).

8.2.1 Place exactly 5 ml water in each impinger.

Leak check the sampling train as follows: Temporarily

insert a vacuum gauge at or near the probe inlet. Then,

plug the probe inlet and pull a vacuum of at least 250 mm

(10 in.) Hg. Note the time rate of change of the dry gas

meter dial; alternatively, a rotameter (0 to 40 ml/min) may

be temporarily attached to the dry gas meter outlet to

determine the leakage rate. A leak rate not in excess of 2

percent of the average sampling rate is acceptable.

NOTE: Release the probe inlet plug slowly before

turning off the pump.

8.2.2 Connect the probe, insert it into the stack,

and sample at a constant rate of 2 liters/min (0.071 cfm).

Continue sampling until the dry gas meter registers about 30

liters (1.1 ft3) or until visible liquid droplets are

carried over from the first impinger to the second. Record

temperature, pressure, and dry gas meter readings as

indicated by Figure 4-4.

357
 358

9.0 Quality Control.

9.1 Miscellaneous Quality Control Measures.

Section Quality Control Effect

Measure
Section 8.1.1.4 Leak rate of the Ensures the
sampling system accuracy of the
cannot exceed four volume of gas
percent of the sampled.
average sampling (Reference Method)
rate or 0.00057
m3/min (0.20 cfm).
Section 8.2.1 Leak rate of the Ensures the
sampling system accuracy of the
cannot exceed two volume of gas
percent of the sampled.
average sampling (Approximation
rate. Method)

9.2 Volume Metering System Checks. Same as Method 5,

Section 9.2.

10.0 Calibration and Standardization.

NOTE: Maintain a laboratory log of all calibrations.

10.1 Reference Method. Calibrate the metering

system, temperature sensors, and barometer according to

Method 5, Sections 10.3, 10.5, and 10.6, respectively.

10.2 Approximation Method. Calibrate the metering

system and the barometer according to Method 6, Section 10.1

and Method 5, Section 10.6, respectively.

11.0 Analytical Procedure.

11.1 Reference Method. Measure the volume of the

moisture condensed in each of the impingers to the nearest

 359

ml. Alternatively, if the impingers were weighed prior to

sampling, weigh the impingers after sampling and record the

difference in weight to the nearest 0.5 g. Determine the

increase in weight of the silica gel (or silica gel plus

impinger) to the nearest 0.5 g. Record this information (see

example data sheet, Figure 4-5), and calculate the moisture

content, as described in Section 12.0.

11.2 Approximation Method. Combine the contents of

the two impingers, and measure the volume to the nearest 0.5

ml.

12.0 Data Analysis and Calculations.

Carry out the following calculations, retaining at

least one extra significant figure beyond that of the

acquired data. Round off figures after final calculation.

12.1 Reference Method

12.1.1 Nomenclature.

Bws = Proportion of water vapor, by volume, in the

gas stream.

Mw = Molecular weight of water, 18.0 g/g-mole

(18.0 lb/lb-mole).

Pm = Absolute pressure (for this method, same as

barometric pressure) at the dry gas meter,

mm Hg (in. Hg).

Pstd = Standard absolute pressure, 760 mm Hg

 360

(29.92 in. Hg).

R = Ideal gas constant,

0.06236 (mm Hg)(m3)/(g-mole)(EK) for metric

units and 21.85 (in. Hg)(ft3)/(lb-mole)(ER)

for English units.

Tm = Absolute temperature at meter, EK (ER).

Tstd = Standard absolute temperature, 293 EK

(528 ER).

Vf = Final volume of condenser water, ml.

Vi = Initial volume, if any, of condenser water,

ml.

Vm = Dry gas volume measured by dry gas meter, dcm

(dcf).

Vm(std) = Dry gas volume measured by the dry gas meter,

corrected to standard conditions, dscm (dscf).

Vwc(std) = Volume of water vapor condensed, corrected to

standard conditions, scm (scf).

Vwsg(std) = Volume of water vapor collected in silica gel,

corrected to standard conditions, scm (scf).

Wf = Final weight of silica gel or silica gel plus

impinger, g.

Wi = Initial weight of silica gel or silica gel

plus impinger, g.

Y = Dry gas meter calibration factor.

)Vm = Incremental dry gas volume measured by dry gas

 361

meter at each traverse point, dcm (dcf).

Dw = Density of water, 0.9982 g/ml

(0.002201 lb/ml).

12.1.2 Volume of Water Vapor Condensed.

(V f & V i)Dw R Tstd

Vwc(std) '
Pstd M w
Eq. 4-1
' K1 (V f & V i)

where:

K1 = 0.001333 m3/ml for metric units,

= 0.04706 ft3/ml for English units.

12.1.3 Volume of Water Collected in Silica Gel.

(W f & W i) R Tstd
Vwsg(std) '
Pstd M w K2
Eq. 4-2
' K3 (W f & W i)

where:

K2 = 1.0 g/g for metric units

= 453.6 g/lb for English units

K3 = 0.001335 m3/g for metric units,

= 0.04715 ft3/g for English units.

12.1.4 Sample Gas Volume.

 362

V m Y P m Tstd
Vm(std) '
Pstd T m
Eq. 4-3
Vm Pm
' K4 Y
Tm

where:

K4 = 0.3855 EK/mm Hg for metric units,

= 17.64 ER/in. Hg for English units.

NOTE: If the post-test leak rate (Section 8.1.4.2)

exceeds the allowable rate, correct the value of Vm in

Equation 4-3, as described in Section 12.3 of Method 5.

12.1.5 Moisture Content.

Vwc(std) % Vwsg(std)
Bws ' Eq. 4-4
Vwc(std) % Vwsg(std) % Vm(std)

12.1.6 Verification of Constant Sampling Rate. For

each time increment, determine the )Vm. Calculate the

average. If the value for any time increment differs from

the average by more than 10 percent, reject the results, and

repeat the run.

12.1.7 In saturated or moisture droplet-laden gas

streams, two calculations of the moisture content of the

stack gas shall be made, one using a value based upon the
 363

saturated conditions (see Section 4.1), and another based

upon the results of the impinger analysis. The lower of

these two values of Bws shall be considered correct.

12.2 Approximation Method. The approximation method

presented is designed to estimate the moisture in the stack

gas; therefore, other data, which are only necessary for

accurate moisture determinations, are not collected. The

following equations adequately estimate the moisture content

for the purpose of determining isokinetic sampling rate

settings.

12.2.1 Nomenclature.

Bwm = Approximate proportion by volume of water

vapor in the gas stream leaving the second

impinger, 0.025.

Bws = Water vapor in the gas stream, proportion by

volume.

Mw = Molecular weight of water, 18.0 g/g-mole

(18.0 lb/lb-mole).

Pm = Absolute pressure (for this method, same as

barometric pressure) at the dry gas meter,

mm Hg (in. Hg).

Pstd = Standard absolute pressure, 760 mm Hg

(29.92 in. Hg).

R = Ideal gas constant,

0.06236 [(mm Hg)(m3)]/[(g-mole)(K)]

 364

for metric units and

21.85 [(in. Hg)(ft3)]/[(lb-mole)(ER)] for

English units.

Tm = Absolute temperature at meter, EK (ER).

Tstd = Standard absolute temperature, 293 EK

(528 ER).

Vf = Final volume of impinger contents, ml.

Vi = Initial volume of impinger contents, ml.

Vm = Dry gas volume measured by dry gas meter,

dcm (dcf).

Vm(std) = Dry gas volume measured by dry gas meter,

corrected to standard conditions, dscm (dscf).

Vwc(std) = Volume of water vapor condensed, corrected to

standard conditions, scm (scf).

Y = Dry gas meter calibration factor.

Dw = Density of water, 0.09982 g/ml

(0.002201 lb/ml).

12.2.2 Volume of Water Vapor Collected.

(V f & V i)Dw R Tstd

Vwc(std) '
Pstd M w
Eq. 4-5
' K5 (V f & V i)

where:

K5 = 0.001333 m3/ml for metric units,

= 0.04706 ft3/ml for English units.

 365

12.2.3 Sample Gas Volume.

V m Y P m Tstd
Vm(std) '
Pstd T m
Eq. 4-6
Vm Pm
' K6 Y
Tm

where:

K6 = 0.3855 EK/mm Hg for metric units,

= 17.64 ER/in. Hg for English units.

12.2.4 Approximate Moisture Content.

Vwc(std)
Bws ' % Bwm
Vwc(std) % Vm(std)
Eq. 4-7
Vwc(std)
' % (0.025)
Vwc(std) % Vm(std)

13.0 Method Performance. [Reserved]

14.0 Pollution Prevention. [Reserved]

15.0 Waste Management. [Reserved]

16.0 Alternative Procedures.

The procedure described in Method 5 for determining

moisture content is acceptable as a reference method.

17.0 References.

1. Air Pollution Engineering Manual (Second Edition).

Danielson, J.A. (ed.). U.S. Environmental Protection

 366

Agency, Office of Air Quality Planning and Standards.

Research Triangle Park, NC. Publication No. AP-40. 1973.

2. Devorkin, Howard, et al. Air Pollution Source

Testing Manual. Air Pollution Control District, Los

Angeles, CA. November 1963.

3. Methods for Determination of Velocity, Volume, Dust

and Mist Content of Gases. Western Precipitation Division

of Joy Manufacturing Co. Los Angeles, CA. Bulletin WP-50.

1968.

18.0 Tables, Diagrams, Flowcharts, and Validation Data.

 367

Figure 4-1. Moisture Sampling Train-Reference Method

 368

Figure 4-2. Moisture Sampling Train - Approximation

Method.
 369

Plant
Location
Operator
Date
Run No.
Ambient temperature
Barometric pressure
Probe Length
SCHEMATIC OF STACK CROSS SECTION
Traverse Sampling Stack Pressure Meter )Vm Gas sample Temperature
Pt. No. Time Temperature differential Reading gas m3 temperature at of gas
(1), min EC (EF) across orifice sample (ft3) dry gas meter leaving
meter )H volume condenser
mm (in.) H2O m3 (ft3) Inlet Outlet or last
Tmin Tmout impinger
EC(EF) EC(EF) EC(EF)

Average
Figure 4-3. Moisture Determination. - Reference Method
 370

Location Comments:
Test
Date
Operator
Barometric pressure

Clock Time Gas volume Rate meter Meter

through setting temperature
meter, (Vm), m3/min E C (E F)
m3 (ft3) (ft3/min)

Figure 4-4. Example Moisture Determination Field Data

Sheet - Approximation Method.

Impinger Silica gel

volume, ml weight, g

Final
Initial
Difference

Figure 4-5. Analytical Data - Reference Method.