VM-7 VM-741B LOCAL COMMUNICATION &

MONITORING SYSTEM
PHASE MARKER MODULE
SPECIFICATIONS Page 1 of 4

No entry if additional
Model Code / Additional Spec. Code ( spec. code is not specified. )

【When "Security function" is not selected】

VM-741B /MEM /NB1 /CSU /TRP /TB

EVENT HISTORY BACKUP Non-incendive Custom setup Tropical spec. I/O terminal block for:
1 Class I Division 2 CSA 1 VM-761B instrument rack
2 VM-762B instrument rack

【When "Security function" is selected】

VM-741B2 /MEM /NB1 /CSU /TRP /TB

Security Function*1 EVENT HISTORY BACKUP Non-incendive Custom setup Tropical spec. I/O terminal block for:
Available 1 Class I Division 2 CSA 1 VM-761B instrument rack
2
(Achilles Certificate Level2) 2 VM-762B instrument rack

Specification

PHASE MARKER INPUT OUTPUT

Input points (tachometer) : 4 points Monitor output : Input signal is output via a buffer amplifier
Location : BNC (Front) and connector (Back)
Input Impedance : 50kΩ
Output Impedance : Approx. 100Ω
Input voltage range : Less than 50Vp-p Output current : Max. 5mA
Hysteresis : 1V, 2V, 5V Pulse output : Shaped pulse signal is output via a buffer amplifier.
Maximum rotation speed : 60,000rpm Location : BNC (Front)
Signal waveform : 0V (VOL), 5V (VOH)
PHASE MARKER INPUT TRANSDUCER Output Impedance : Approx. 100Ω
Proximity transducer : FK-202F, RD-05A Output current : Max. 5mA

OPERATION CONTACT INPUT Transducer power supply

: proximity transducer
RES : Outside reset signal -24VDC±10% / 25mA Max.
SEQ : Sequence signal Contact output : SYS-OK
FIL : Filter enable signal Output points : 1
Contact type : Dry contact (SPDT)
OUTPUT Enagization method
Indicators : DAN LED (Red) : Normally de-energized or
On : When DANGER alarm occurs Normally energized field changeable
(This indicator lights up when DANGER alarm is output Contact capacity : 250VAC/5A, 30VDC/5A
from at least one of the modules stored in the instrument ALARM
rack .)
Alarm reset : AUTO-RESET or SELF-HOLD field changeable.
Off : During normal status
ALT LED (Yellow)
On : When ALERT Alarm occur PROGRAMMABLE INDICATOR COMMUNICATION
(This indicator lights up when ALERT alarm is output
Network : RS-485
from at least one of the modules stored in the instrument
rack .) Protocol : Modbus/RTU
Off : During normal status Connector : 5-pin connector (Back side of rack)
SYS-OK LED (Green)
On : During normal status MCL VIEW (VM-771B) COMMUNICATION
Flash : When OK alarm occurs Network : Ethernet 100Base-TX
(This indicator flashes when an input abnormality of the Protocol : TCP/IP
phase marker signal is output or an OK alarm is output
within the rack.) Connector : RJ-45 (Back side of rack)
D-BYP LED (Red) DEVICE CONFIG (VM-772B) COMMUNICATION
On : While the DANGER bypass is set
Off : During normal status Network : USB 2.0/1.1
COMM LED (Green) Connector : Type-B (Front side of rack)
On : Communication is connected
Flash : Communication data is being passed
Off : Communication is disconnected
TRG LED (Yellow)
On : A phase marker pulse is not detected
Flash : A phase marker pulse is detected

6H14-106 Rev.4
Issued Feb. 2015
Revised Mar. 2019
 VM-7 VM-741B LOCAL COMMUNICATION &
MONITORING SYSTEM
PHASE MARKER MODULE
SPECIFICATIONS Page 2 of 4

Specification

SECURITY FUNCTION*
1 MATERIAL and FINISH
Network : Ethernet 100Base-TX Face plate : ABS (Black)
Protocol : TCP/IP Sheet : Polyester tough top (Gray)

Connector : RJ-45(Back side of rack) Base plate : Alminium alloy (Silver)

Filter function : None(non-compliant Security Function) MASS

Off(Filter OFF : Maintenance only) Body : Max. 1.0 kg (2.2 lb)
On(Filter ON : In Operation)
ACCESSORY SPECIFICATION CODE / IDENTIFIED BY TB□
Client MAC Address : MAC Address of PC for MCL View
Client IP Address : IP Address of PC for MCL View Quantity
Code Accessory
(Part Code)
*1 About the Security Function /TB1 Phase Marker input terminal block plug (15pin) 1piece
・When selecting the presence of "security function", other networks FRONT-MC-1.5/15-STF-3.81(PHOENIX CONTACT) (7072NAB)
(VM-742B: Fieldbus(Modbus / TCP), Analysis software communication Phase Marker input terminal block plug (6pin) 1piece
(TCP / IP)) to unify security policies are also " Please select the presence of FRONT-MC-1.5/6-STF-3.81(PHOENIX CONTACT) (7072NAC)
security function ". SYSTEM-OK output terminal block plug (6pin) 1piece
・Custom setup of "Security function" can’t be order. FRONT-MC-1.5/6-STF-3.81(PHOENIX CONTACT) (7072NAC)
・Select "Security Function", you can meet a global certification program Contact input terminal block plug (6pin) 1piece
(Achilles Certification Level 2) that proves to have a certain network FRONT-MC-1.5/6-STF-3.81(PHOENIX CONTACT) (7072NAC)
robustness. /TB2 SYSTEM-OK output terminal block plug (6pin) 1piece
・Achilles is a registered trademark of GE Digital. FRONT-MC-1.5/6-STF-3.81(PHOENIX CONTACT) (7072NAC)

ENVIRONMENTAL CONDITION Contact input terminal block plug (6pin) 1piece

FRONT-MC-1.5/6-STF-3.81(PHOENIX CONTACT) (7072NAC)
Operating temperature : 0 to +65°C
Note) *1 D-sub plugs and hoods are not included in this code. Please make
Storage temperature : -30 to +85°C necessary arrangement separately, if required.
Relative humidity : 20 to 95%RH (non-condensing) *2 When individually ordering specify the parts code, it is require
to arrange for a necessary amount.
POWER CONSUMPTION
Module alone : Less than 15W ! WARNING
Some functions may not be available with old version.
For details, please refer to "infiSYS Family Improvement
Information" (6H16-011).

Default Value

INPUT (PHASE MARKER) SECURITY FUNCTION(Case of None)

Not used Filter : None

SYSTEM-OK ALARM Client MAC Address : FF-FF-FF-FF-FF-FF

Alarm reset : Auto Reset Client IP Address :192.168.8.100

Enagization method : NORMALLY DE-ENERGIZED SECURITY FUNCTION(Case of Available)

Relay logic : “OR” of all OK alarm Filter : Off

COMMUNICATION Client MAC Address : FF-FF-FF-FF-FF-FF

IP Adress : 192.168.8.8 Client IP Address :192.168.8.100

Subnet mask : 255.255.255.0 OTHERS

IP Port No. : 8888

Alarm Contact Operation

Power ON
Contact type Enagization method Power OFF
Normal state Alarm state
NORMALLY DE-ENERGIZED OPEN OPEN CLOSE
N.O. contact
NORMALLY ENERGIZED OPEN CLOSE OPEN
NORMALLY DE-ENERGIZED CLOSE CLOSE OPEN
N.C. contact
NORMALLY ENERGIZED CLOSE OPEN CLOSE

6H14-106 Rev.4
Issued Feb. 2015
Revised Mar. 2019
 VM-7 VM-741B LOCAL COMMUNICATION &
MONITORING SYSTEM
PHASE MARKER MODULE
SPECIFICATIONS Page 3 of 4

Plug/ Terminal Block (Connector) Pin Assignment

VM-761B Instrument Rack

(Back)
1 Monitor Output Connector

2 Phase Marker Input Terminal Block

3 Phase Marker Input Terminal Block

4 SYSTEM-OK Output Terminal Block

5 Contact Input Terminal Block

Back of Instrument Rack Plug/ Terminal Block (Connector) Pin Assignment Fitting Plug Part Code

1 CH1 MON 6 CH3 MON

Plug
1 2 CH1 COM 7 CH3 COM
7072NAD
3 CH2 MON 8 CH4 MON
Hood
4 CH2 COM 9 CH4 COM
5 N/A
7072NAG

2 A1 CH1 SIG
A2 CH1 COM
A3 N/A
A
A4 CH1 POW
A5 CH1 SHIELD
A6 CH2 SIG
A7 CH2 COM
A8 N/A 7072NAB
A9 CH2 POW
A10 CH2 SHIELD
A11 CH3 SIG
A12 CH3 COM
A13 N/A
A14 CH3 POW
A15 CH3 SHIELD

3 B B1 CH4 SIG
B2 CH4 COM
B3 N/A
7072NAC
B4 CH4 POW
B5 CH4 SHIELD
B6 N/A

4 C C1 N/A
C2 N/A
C3 N/A
7072NAC
C4 N.O.
C5 SYSTEM-OK
C6 N.C.

5 D D1 RES1
D2 RES2
D3 SEQ1
7072NAC
D4 SEQ2
D5 FILT1
D6 FILT2

Note) For the accessory specification code “/TB1”, the fitting terminal block plugs 2 3 4 5 are included.
For the accessory specification code “/TB1”, the D-sub plug and hood 1 are not included. If required,
please make necessary arrangement separately referring to the part code above.

6H14-106 Rev.4
Issued Feb. 2015
Revised Mar. 2019
 VM-7 VM-741B LOCAL COMMUNICATION &
MONITORING SYSTEM
PHASE MARKER MODULE
SPECIFICATIONS Page 4 of 4

Plug/ Terminal Block (Connector) Pin Assignment

VM-762B Instrument Rack

(Back) 1 Monitor Output Connector

2 Phase Marker Input Connector

3 SYSTEM-OK Output Terminal Block

4 Contact Input Terminal Block

Back of Instrument Rack Plug/ Terminal Block (Connector) Pin Assignment Fitting Plug Part Code

1 1 CH1 MON 6 CH3 MON

Plug
2 CH1 COM 7 CH3 COM
7072NAD
3 CH2 MON 8 CH4 MON
Hood
4 CH2 COM 9 CH4 COM
5 N/A
7072NAG

2 A1 CH1 IN A20 CH4 IN

A2 CH1 COM A21 CH4 COM
A3 N/A A22 N/A
A
A4 CH1 POW A23 CH4 POW
A5 CH1 SLD A24 CH4 SLD
A6 CH2 IN A25 N/A
A7 CH2 COM A26 N/A
A8 N/A A27 N/A
Plug
A9 CH2 POW A28 N/A
7072NAF
A10 CH2 SLD A29 N/A
Hood
A11 CH3 IN A30 N/A
A12 CH3 COM A31 N/A
7072NAJ
A13 N/A A32 N/A
A14 CH3 POW A33 N/A
A15 CH3 SLD A34 N/A
A16 N/A A35 N/A
A17 N/A A36 N/A
A18 N/A A37 N/A
A19 N/A

3 C C1 N/A
C2 N/A
C3 N/A
7072NAC
C4 N.O.
C5 SYSTEM-OK
C6 N.C.

4 D D1 RES1
D2 RES2
D3 SEQ1
7072NAC
D4 SEQ2
D5 FILT1
D6 FILT2

Note) For the accessory specification code “/TB2”, the fitting terminal block plugs 3 4 are included.
For the accessory specification code “/TB2”, the D-sub plugs and hoods 1 2 are not included. If
required, please make necessary arrangement separately referring to the part code above.

6H14-106 Rev.4
Issued Feb. 2015
Revised Mar. 2019