1 GENER Tag No.

xxxxxx (To be Clarification)

2 AL Service
3 Line No.
7 Line Size 10 In To be Clarification
8 Pipe Material Carbon Steel
PIPE

9 Pipe Insulation None

10 Design Pressure 300 Psig To be Clarification
11 Design Temperature 90 °F
12 Process Fluid Process Gas
13 Units @Maximum @Normal Flow @Minimum Flow
PROCESS CONDITION

14 Flow Rate Msft3/d 20 10 5

15 Inlet Pressure psig 300 150 150
16 Pressure Drop psig 5 10 10
17 Inlet Temperature °F 90,00 80 80
19 Inlet Density lb/ft3 1.135 0.58976 0.59171
22 Inlet Specific Heat Ratio 1.2669 1.2726 1.2699
24 Critical pressure Psia 673.48 676.95 673.48
26
27
28 Calculated Cv Note 1
CALCULATE
D RESULTS

29 Travel Note 1
30 Sound Pressure Lavel dBa
31
32
33 MFR Model Fisher or Equal Note 1 66 MFR Model N/A N/A

SOLENOID VALVE
34 Body Type Material Globe Carbon Steel 67 Quantity N/A
35 Body Size 6 in Note 1 68 Local Manufacture Reset
36 End Connection & Rating RF 300# 69 Area Classification N/A
37 Bonnet Type Material Standard Carbon Steel 70 Material / Trim Body N/A
38 Flow Direction Flow to Open Note 1 71 Body Size / No. of Part N/A
BODY AND TRIM

39 Bolt & Nut Material ASTM A194 2H 72 Cable Entry / Coil Installation N/A
40 Packing Material PTFE 73 Tag. No N/A
Extension Bonnet Note 1 MFR N/A

SWITCHES
41 74 Model N/A
42 Trim Type Single Seated 75 Type Quantity N/A N/A
43 Trim Size Note 1 76 Contact / Rating N/A
44 Rated Cv Note 1 77
45 Characteristic Quick Opening 78 MFR Model Note 1 Note 1
46 Rated Travel Note 1 79 Air Set Yes
Plug / Ball / Disc Material 316 SS Filter
REGULATOR

47 80 Gauge Yes Yes

AIR FILTER

48 Seat Material 316 SS 81 End Connection 1/4" NPTF

49 Case Material Stem Material 316 SS 316 SS 82 Body Alumunium
50 MFR Model Note 1 Note 1 83 Trim 316 SS
51 Type Size Diaphragm Note 1 84 Packing PTFE
52 Close At Open At MTR STD MTR STD 85
ACTUATOR

53 On-Off Modulating N/A Yes 86

54 Req'd Air Supply Press 80 - 272 Psig 87 Handwheel No
OTHER ACC

55 Failure Position Closed 88 Lubricator Fitting No

56 Act.Orientation Vertical Up 89 Lock-up System
57 Stroke Speed Travel Indicator Note 1 Yes 90 Quick Exhaust Valve No
58 Flow Action To Open 91 Speed Control No
59 MFR Model Note 1 Note 1 92 Marking & Identification No
POTENSIONER

60 Potensioner Type Smart E/P Potensioner 93 Body Paint & Color Note 1
PAINT

61 Signal Input Output 4 - 20 mA dc Note 1 94 Actuator Paint & Color Note 1

62 Air Supply Min/Norm/Max 80/100/272 Psig 95
63 Enclosure / Area Classification NEMA 7 and NEMAA 4X 96
TESTS

64 Filter Reg / Gauge / Bypass Yes / Yes 97

65 Electrical/ Phenumatic Conn 1/2" NPT /1/4" NPT 98
Note :
1. To be clarification

A 28-Aug-20 AGL
Rev Description DATE PREPARED CHECKED APPROVED
CLIENT : Pertamina EP
DATA SHEET
PROJECT Upgrading Metering
PT. DWI TUNGGAL JAYA AGUNG
DATA SHEET No.
PRESSURE CONTROL VALVE
PROJECT No. REVISION A
 Control Valve - Gas or Steam flow 25/08/2020

Calculation Control Valve

Project CV-101. Upgrading Meter system Fajar Wisesa.

Tag number CV-101 By FRM
Input data App AGL
Valve
Data : 6 in Globe : Quick Open. Ports : Two. Flow to : Between
Rated Cv : 550.8. Rated xT : .68. Style Fd : .7

Pipe sizes
Inlet : in. Outlet : in. Outlet pipe wall : .365 in

Fluid data
Gas mixture components Gas property factor: 1,2 dbA
4,55% Carbon Dioxide, 3,91% Nitrogen, 82,7% Methane, 3,44% Ethane, 3,17% Propane,
0,81% Butane-n, 0,71% Butane-Iso, 0,16% Pentane-n, 0,23% Pentane-Iso, 0,32% Hexane-n,
Maximum Normal Minimum Units
Percent of nominal flow 100 50 25
Gas flow 20 10 5 Msft3/d
Pressure drop 5 10 10 psi
Flow temperature 90 80 80 degF
Inlet pressure 300 150 150 psig
Cp/Cv Sp heat ratio 1.2669 1.2726 1.2699
Molecular weight 20.238 20.174 20.238
Density @ FTP 1.135 .58976 .59171 lb/ft3
Critical pressure 673.48 676.95 673.48 psia
Critical temperature 375.435 375.435 375.435 degR
Accoustic efficiency

Output data
Required Cv 297.9 149.3 74.77
Percent of valve lift 54 27 14
Noise level: dbA
Status Normal Normal Normal
Sonic minimum size 1.243 1.237 .8754 in
User saved volume units, data for all calculations, calculate size
Source - ANSI/ISA-75.01.01-2012 Flow Equations for sizing control valves
Accuracy - Within the limits of ANSI/ISA 75.01
InstruCalc Ver.9.0.3.

Notes
Preliminary Calculation