K.

Kadlec: Measurement and Control

LEVEL MEASUREMENT SYSTEMS

• Level measurements is an integral part of process control,
and may be used in a variety of industries
• Level measurement may be divided into two categories:
¾ point level measurement
¾ continuous level measurement
• Point level sensors are used to mark a single discrete
liquid height, a preset level condition (as a high alarm or a
low alarm condition)
• Continuous level sensors provide an analog output that
directly correlates to the level within the containing vessel.
This analog signal may be directly linked to a visual indicator
or to a process control loop, forming a level management
system.

The material to be measured

• Liquid
– from pure, clean water to viscous, sticky, and
corrosive and abrasive fluids
• Bulk material
– from free-flowing, dry crystals to moist, lumpy solids

The processing environments for level sensors extend

from vacuum to high-pressure service, and from subzero
to elevated temperatures.

Level sensors
• Mechanical sensors
– Float methods
– Buoyancy method
– Vibrating level systems
• Hydrostatic pressure methods
– Differential pressure level detectors
– Bubbler systems
• Electrical methods
– Conductivity probes
– Capacitance probes
– Optical level switches
– Ultrasonic level detectors
– Microwave level systems
– Nuclear level systems
3

7-M&C08_Level.doc 28.3.2008 1 Level measurement

K. Kadlec: Measurement and Control

Floats
• The basic float arm indicator comprises very simply a float
connected to a pivoted arm that drives pointer or a switch.
• The unit can be made for either side- or top- entry.
• Moving parts present a very definite disadvantage, since they are
situated in the liquid and are thus prone to corrosion and seizing
• Methods of the providing indication other then by linkage to a
pointer include the use of a potentiometer, or of magnetic or
inductive coupling

Magnetic
Switch Float switch

Float

Design of floats
Floats with transmission linkage:

Floats with magnetic switches:

Float

Non-magnetic
guide bar
5

Buoyancy method
• These devices use Archimede's principle
• The mechanical level indicator consists of the immersion body with
calibrated measuring spring which transmits the change of level to the
mechanical or electrical indicator
π r2 (Δ h - Δ l ) ρ g = k . Δ l
Mechanical
indicator
Spring or electronic
transmitter

Δl Spring
Immersion
body
φd

Immersion
body
ρ Δh
Δl

7-M&C08_Level.doc 28.3.2008 2 Level measurement

K. Kadlec: Measurement and Control

Vibrating level switches

Principle: A vibrating fork or blade
• An electronic circuit excites the blade of probe to its resonant frequency,
and when material comes into contact with the blade, vibration is
damped causing switching of the relay
• This device is suitable for control maximum levels of solids and liquids in
many types of applications (e.g. foods, grains, granules, pellets, cement,
powder)

Principle: Design:

Vibrating element

Hydrostatic pressure methods

• The hydrostatic pressure at the bottom of a container is directly
proportional to the liquid height
Measurement in an open vessel: Measurement in an enclosed vessel:
p1

h h

P Pd
p=hρg
Δp=hρg
Diaphragm system for
hydrostatic pressure
measurement
8

Bubbler systems
• Clean air from a compressor is forced through a restriction into a tube
that leads to the bottom of the tank
• The air pressure after the restriction is equal to the hydrostatic
pressure at the bottom of the tank
Measurement in an open tank: Measurement in an enclosed tank:
p=hρg
Pd
P

p1
Pressure Pressure
controller controller

h h

Compressed air pn > hmax ρ g Compressed air 9

7-M&C08_Level.doc 28.3.2008 3 Level measurement

K. Kadlec: Measurement and Control

Conductivity level probes

– only for electrically conductive liquids
Continuous level sensing:
Metal wall

h
h

Discrete level
Tank from non-conducting indications:
material (plastic)

Advantages: hmax
– low costs
– simple electronic circuits hmin
– no moving parts 10

Capacitance level probes

for nonconductive liquids:
ε0 - permittivity of free space
Principle: C =ε0ε r S/d εr - relative permittivity
S - area of electrodes
d - electrode distance
CB hmax
CA h Reference capacitor for
compensation relative
permittivity changes:
Cylindrical type
C = CA + CB sensor:

CB
CB
h CA
CA h h
CR
11

Capacitance level probes

for conductive liquids:
• An insulated electrode is used (e.g. an insulated rod)
• The insulator may be polytetrafluorethylene or polyethylene
• The conductive liquid forms the second electrode
• With increasing liquid level increases the area of the second
electrode as well as capacitance
• An electronic transducer converted capacitance changes into a
voltage or current signal

Insulated
electrode

h Electrically
conductive liquid

12

7-M&C08_Level.doc 28.3.2008 4 Level measurement

K. Kadlec: Measurement and Control

Capacitance level probes design

Measuring unit Sensor for discrete indication:

Probe

Capacitance probe Transducer

Applications:
• Suitable for measuring of liquids and bulk (loose) materials
• Suitable for wide temperature ranges (from -40 to +200) °C and
high pressures
• Unsuitable for measuring foaming liquids
13

Optical level switches

• Light must be transmitted and then received
• Optical level sensors consist of:
– Light source (bulb, LED)
– Photoelectric detector (photodiode, phototransistor, photoresistor)
• Devices works with infrared or visible radiation

Design of level switches:

Light is reflected back to the detector by
Light Photoelectric the conical tip of a quartz light conductor
source detector

S
S D
D
glass
prism

S
D

14

Ultrasonic level measurement

The measuring equipment consists:
• A transmitter that periodically sends a sound pulse to the surface of
the liquid
• A receiver that amplifies the returning pulse
• A time interval counter that measures the time elapsing between the
transmission of a pulse and receipt of the corresponding pulse echo

t t
L=c⋅ h = Lmax − c ⋅
T R 2 2
c - sonar pulse velocity [m.s-1]
L t - time [s]
L - distance [m]
Lmax
Influencing, interaction:
h • gas density
• temperature
• mixing device
• foaming liquid
15

7-M&C08_Level.doc 28.3.2008 5 Level measurement

K. Kadlec: Measurement and Control

Ultrasonic level-meter with compensation

• Compensation of the influence of the gas density changes
• Cyclical measurement of the sonar pulse velocity in the environment
• Automatic compensation

L2 L3
Transmitter/Receiver Electronic
circuits

Reference
L1 element h = L3 - L2

L3 L2
The sonar pulse velocity is calculated:
c = 2 L1 / t1
t1 - time for the reference element distance
h

16

Ultrasonic level-meter design

Smart sensor for level measurement
• Ultrasonic transmitter and receiver Electronic
(piezoelectric principle) circuits
• Microprocessor controlled electronic
circuits
• Analog and digital output signal
Smart transducer Ultrasonic
transmitter
and receiver

Sensor on the tank cover

Ultrasonic transmitter
and receiver 17

Microwave level systems

• They are parallels in the operating principles of ultrasonic systems with
microwave radar level systems
• Much higher frequencies (around 10 GHz) are used in radar system
• The radar beam is not affected by density changes

Pulse method:
• Microwave pulses are transmitted in
Radar short cycles
antenna • The time is measured (ps)
A
• Demanding at the time measuring
accuracy

L L =c⋅
t
h = Lmax − c ⋅
t
Lmax 2 2
c - microwave velocity [m.s-1]
h t - time [s]
L - distance [m]
18

7-M&C08_Level.doc 28.3.2008 6 Level measurement

K. Kadlec: Measurement and Control

Frequency Modulated Continuous Wave method

frequency
fmax • The antenna
transmits a A
microwave signal
f1 with continuously
varying frequency f1 f0
towards the liquid
f0 surface.

fmin
t0 t1 čas
• When the reflected signal f0 returns to the receiver, it is mixed with the
outgoing signal f1.
• There will be a difference in frequency between the transmitted and the
reflected signals Δ f = f1 − f0
• The difference in frequency is proportional to the time difference Δ t = t1 − t0
and also to the distance to the liquid surface.
• The frequency difference can be measured very accurately. 20

Radar level gauge design

Radar antennas: Radar sensors on the tank cover:

Display
Smart level sensor
• uses Fast Fourier Transformation
Antenna • microprocessor controlled circuits
• analog and digital output signal
• high accuracy (± 5 mm)
21

Nuclear level systems

• Nuclear radiation from a selected source can be related to liquid or solids
levels in a vessel
• Cobalt-60, cesium-137 or radium-226 is used as the gamma radiation source
• The radioactive source is capable of transmitting through the container wall
• As a detector for converting nuclear gamma ray radiation into electrical
quantities related to level, some systems use Geiger counters

Discrete level indication: Continuous level measurement:

Intensity of radiation depends
D on the liquid level
S D Applications:
• liquid and solids
level
Source Detector • liquid/liquid
interface
• high temperature
and pressure
S D • high viscosity
• aggressive medias
S
Source 22

7-M&C08_Level.doc 28.3.2008 7 Level measurement

K. Kadlec: Measurement and Control

Some guidelines for selecting instruments

to be used for the indication or control of level
• The material to be measured must be looked at to determine its
compatibility with the instrumentation. For instance: Is the liquid hot, cold,
under pressure, viscous, corrosive, abrasive, hygienic ?
• Is the area hazardous, requiring intrinsically safe or flameproof products ?
• Can the sensor contact the material being measured ?
• Can the sensor be inserted into an existing entry or does it require new
"hole" ?
• Does the instrument have to be top-enter or can be mounted in the side ?
• Is point or continuous measurement desirable ?
• Is remote control or indication desirable ?
• Are there objection to the mechanical moving parts ?
• The question must be asked whether or not the equipment need be
compatible with data loggers microprocessor or computers.
• What is the required accuracy of the measurement ?
• What are costs ?

23

References
• Anderson A.A.: Instrumentation for Process Measurement and
Control. CRC Press, Boca Raton, 1998
• Altmann W.: Practical Process Control for Engineers and technicians.
Elsevier, Amsterdam, 2005
• Bentley J.P.: Principles of Measurement Systems.
Pearson Education Limited, 2005
• Dyer A.S.: Survey of Instrumentation and Measurement.
John Wiley, Inc. New York, 2001
• McMillan G.K., Considine D.M.: Process/Industrial Instruments and
Controls Handbook. McGraw/Hill, New York, 1999

All texts for lectures Measurement technique are on web-sides:

http://www.vscht.cz/ufmt/kadleck.html

23

7-M&C08_Level.doc 28.3.2008 8 Level measurement