Micom General Catalogue PDF

Automation & Information Systems
Protection
Relays Guide 2012
2012
www.schneider-energy.pl
[ Protection Relays Guide ] List of ANSI Codes Applied in the Guide 2
List of ANSI codes applied in the Guide

ANSI Code Main Protection Function
50/51 Non-directional phase overcurrent
50N/51N Non-directional earth fault
67 Directional phase overcurrent
67N Directional earth fault
67YN Admitance earth fault
37 Phase undercurrent / Loss of load
49/51 Thermal overload
46 Negative phase sequence thermal_I2 / Unbalance load
46BC Broken conductor detection
50BF Circuit breaker failure
79 Multi-shot autoreclose
32N/67W Wattmetric earth fault
27 Phase undervoltage
59 Phase overvoltage
47 Negative sequence overvoltage _ U2
27D Positive sequence undervoltage _ U1
59N Residual overvoltage / Neutral displacement _ Uo
27TN // 59TN 100% stator earth fault ( 3 harm. )_neutral // terminal
87 Differential
32R // 32F Reverse power_R // Directional power _ F (3 ph measure)
32O Overpower
32L Low forward power
81O Overfrequency
81U Underfrequency
81R Rate of change of frequency _ df/dt / ROCOF /
81AB Turbine abnormal frequency
VVS* Voltage vector shift _ dU >
40 Loss of field
24 Overfuxing_U/Hz
51V Voltage dependent overcurrent
21 Underimpedance / Impedance / Distance
64N // 87N Restricted earth fault (differential)
50DT Interturn (Split Phase)
64R Rotor earth fault
50 / 27 Unintentional energisation at standstill // Dead machine
78 / 68 Pole slipping_Power swings
26 / 38 Temperature detectors
48 Excess long start
51LR // 50S Locked rotor at start // Satalled rotor
66 Start number
ABS* Anti Back Spin
55 Out of step
25 Check synchronising
74TCS Trip Circuit Supervision
FL* Fault locator
50HS Switch On To Fault
VTS/CTS Measure circuit supervision
Function symbols in accordance with ANSI / IEEE Std C37.2 - 1996 Standards
* - the symbol does not appear in the Standard
[ Protection Relays Guide ] Contents 3
CONTENTS:
System Products..............................................................................................................................4
Overcurrent Protections...............................................................................................................6
MV Bay Protections.........................................................................................................................12
Motor Protections............................................................................................................................16
Generator Protections...................................................................................................................20
Line Distance Protections.............................................................................................................24
Line Differential Protections........................................................................................................29
Differential Protections for Transformers, Generators and Motors..............................32
Voltage Protections........................................................................................................................34
Busbar Protections.........................................................................................................................36
MV Changeover Automation.......................................................................................................38
Accessories........................................................................................................................................39
Services...............................................................................................................................................41
MV Network Automation / Easergy Range of Products.....................................................42
Network Analysers / Metering and Control Devices............................................................44
SEPAM Range of Protections.......................................................................................................46
Product Catalogue (DVD) / MiCOM S1 Studio Software..................................................48
Product Tables..................................................................................................................................49
Contact Details / Service Info-Line
Make the most of your energy

[ Protection Relays Guide ] System Products 4
PACiS
Protection, Automation & Control integrated Solution
CONTROL AND SUPERVISION SYSTEM FOR ELECTRICAL POWER SUBSTATIONS
• Signalling and remote control

• Execution of substation schemes
• Measurement processing
• Distributed Architecture
• Flexible topology
• IEC61850 100MBit/s STP6 system bus or
optical fibre, Client-Server relation, GOOSE
events, integration of equipment produced
by various manufacturers
• Conversion of data format between
a digital device and SCADA
• Possibility to test equipment operations
by means of software simulators
• Diverse interfaces of data transmissions
• Control and supervision over all types
of substations
MiCOM C264 C / MiCOM C264 P

MODULAR SUBSTATION COMPUTER AND SYSTEM BAY MODULE,
COMMUNICATION CONCENTRATOR, PROTOCOL CONVERTER
Control and signalling circuits Application

• Possibility to count impulses on inputs • Bay unit with synchro-check
• Direct inputs for CTs and VTs • Transformer voltage regulator
• Transducer measurements 0 - 20 mA • Protocol concentrator (gateway)
• Configurable schemes in accordance with IEC • Back-up protection
61131-3 standard, switchgear interlocking • Modular substation computer - execution of
• Integrated schemes of synchro-check and control sequences, regulator schemes, interbay
transformer voltage regulator interlocks
• Record of up to 2000 events • Mini HMI - visualisation of a substation layout on
• Routing of: Modbus, IEC 60870-5-101, IEC a LCD display
60870-5-103, IEC 60870-5-104, DNP 3.0, • Various combinations of the above
UCA-2, IEC 61850 protocols
• Electrical and optical interfaces
• Used as a stand-alone device or as a part of
PACiS system
• Co-operation with external SCADA systems
(WindEX, SYNDIS, DYSTER, PRINCE etc.)
• Capacity to perform basic protection functions
Documents • Analogue outputs
• Catalogue card
[ Protection Relays Guide ] System Products 5
PACiS Gateway
ACCESS GATEWAY
Application
• 4 doubled communication ports
• Interface between PACiS system bus and a
• Time synchronisation
dispatching centre
• Possibility of parallel operations (redundancy)
• Supervision of modes: remote/local,
Protection and Logic Control
„maintenance”
• Data acquisition, processing and transmission
• Computer without rotating components, power
• Self-diagnosis and monitoring of data transfers
supply within thresholds of safe voltage
• Communication in V.24 and 802.3 standards:
• Windows Embedded software
Slave DNP3, Modbus RTU, IEC 60870-5-101,
IEC 60870-5-104, GI74, OPC, Server/Client
IEC61850
SUI (System User Interface)

HUMAN-MACHINE INTERFACE
Application & Functions Advanced Graphic Features

• Used in HV and SV substations and in other areas of • Graphic libraries in compliance with power engine-
commercial power industry as a local or remote OI ering standards
• Possibility to create multiple Operator Interfaces in • Real-time charts (bar graphs, XY)
systems of distributed architecture • Adjustable level of details - zooming / cluttering,
• Cyber-security compatible with NERC CIP standard, result scaling
certified by US-CERT (authorised login, antivirus • Multilayer images and applications
system, management of access rights, 4 levels of • Simulation tools
password-based protections) • Possibility to create individual software scripts
• Compatible with many platforms, e.g.: XP/Server/
Seven/32bits Other Functionalities
• Designed from scratch using OPC architecture • Data automatic processing (Access/Excel/SQL)
• Report processing • Calculation of measurements
• Configurable filtering of alarms and events • Complexity of characteristics (real-time mode - X/Y -
• Configurable on-line graphic interface bar graphs / log-log plots / pie charts
• Multilingual, with variety of licenses • SNMP configurator, integrated schedule
• Web Server interface
Enhanced Efficiency
• Object including more than 50,000 pieces of data
• „Hot Redundancy” mode - takeover of supervision
functions (without data loss) by a backup computer
• Acquisition and archiving of 5,000 pieces of data per
second in real-time
• Acquisition and archiving of 1,000 measurements
per second in real-time
• Up to 12 data servers (redundant)
• Up to 64 graphic interfaces on the data servers
[ Protection Relays Guide ] Overcurrent Protections 6
MiCOM P120 / MiCOM P121

OVERCURRENT PROTECTION RELAY
Functions: 50/51, 50N/51N
Application Measurements
• Phase and earth fault overcurrent protections • Phase currents
applicable in HV and MV substations and to • Earth current
protect MV and LV transformers
Other Functions
Protections • 2 setting group
• P120: • Circuit breaker control
• Single-phase or earth fault overcurrent, 3-stage • CB status monitoring
DT or IDMT, co-operation with core balanced CT • Protection blocking logic
or in Holmgreen arrangement • Output contact latching
• P121: • Programmable binary inputs, outputs relays and
• 3-phase overcurrent, phase-to-phase, 3-stage, LEDs, 2 inputs / 4 outputs
DT or IDMT • Communication in RS485/RS232 standard
• Earth fault, 3-stage DT or IDMT, co-operation • Transmission protocols: Courier, Modbus,
with core balanced CT or in Holmgreen IEC60870-5-103 and DNP 3.0
Documents
arrangement • Recording of:
• Catalogue card
• Events - 250
• User manual
• Faults - 25 (1600 Hz, 3s window)
• Triggers - 25
• Trips - 5 (display)

OVERCURRENT PROTECTION RELAY (3-phase)
Functions: 50/51, 50N/51N, 37, 49, 46, 46BC, 50BF, 79, 74TCS, 50HS
Application Other Functions
• Phase and earth fault overcurrent protections • 2 setting group
applicable in HV and MV substations and to • Circuit breaker control
protect MV and LV transformers • CB status monitoring
• Protection blocking logic
Protections • Output contact latching
• 3-phase overcurrent, phase-to-phase, 3-stage, • Programmable binary inputs, outputs relays and
DT or IDMT LEDs:
• Earth fault, 3-stage, DT or IDMT • P122 3 inputs / 6 outputs
• Thermal overload with 1 thermal time constant • P123 5 inputs / 8 outputs
• Undercurrent, single stage • Communication in RS485/RS232 standard
• Negative phase sequence overcurrent, IDMT and • Transmission protocols: Courier, Modbus,
DT IEC60870-5-103 and DNP 3.0
• Recording of:
Measurements • Events - 250
• Phase currents • Faults - 25 (1600 Hz, 3s window)
• Earth current • Triggers - 25
• Thermal state • Trips - 5 (display)
Documents
• Catalogue card
• User manual
MiCOM P122C
COMPACT OVERCURRENT PROTECTION RELAY
Functions: 50/51, 50N/51N, 37, 49, 46, 46BC, 50BF, 79, 74TCS, 50HS, CTS
Application
• Circuit breaker failure detection
• Utilities
• Blocking logic for reverse interlocking
• Industrial electrical networks
• Circuit breaker status monitoring
• HV and MV substations
• Trip circuit supervision
• MV and LV transformers
• Switch on to fault
• Cold load pick-up
Protection and Logic Control
• Output contacts testing mode
• 3 independent non-directional phase and earth
overcurrent thresholds
Measurements & Recording
• DT and IDMT curves
• IA, IB, IC, IN, Is1, Is2, Is2/Is1, f, Θ
• Thermal overload
• Rolling and peak phase current values
• Unbalance / Loss of phase
• Recording of events, disturbances and fault
• Loss of load
parameters
• Output contacts latching
• Broken conductor detection Documents
• Catalogue card
• User manual
MiCOM P116
OVERCURRENT PROTECTION RELAY DUAL-POWERED WITH CTs / AUXILIARY SUPPLY VOLTAGE
Functions: 50/51, 50N/51N, 37, 49, 46, 46BC, 50BF, 79, 74TCS

• Phase and earth fault dual-powered overcurrent • Autonomous operation: dual-powered supply
protection applicable in HV and MV substations from current circuits or/and auxiliary voltage
and to protect MV and LV transformers • 4-pole multishot autoreclose
• Applicable in systems where auxiliary supply • 2 setting groups
voltage may be interrupted or lost • Circuit breaker diagnosing
• Circuit breaker control
Protections • Circuit breaker state monitoring
• Overcurrent, against phase-to-phase faults, • Circuit breaker failure detection with
3-stage, DT or IDMT undercurrent criterion
• Earth fault, 3-stage, DT or IDMT • Broken conductor detection
• Thermal overload with 1 thermal time constant • Cold load pick-up logic
• Undercurrent, single stage • Protection blocking logic
• Negative phase sequence overcurrent, IDMT and • Auxiliary output latching
DT • 5 x electromagnetic flag indicator
• Tripping the circuit breaker at a loss of auxiliary
Measurements supply voltage by means of:
• Phase currents • an internal energy tripping output, cooperating
• Earth current with the sensitive voltage coil of the circuit
breaker (CB ordering option): 24VDC or 12VDC
• MiCOM E124 - an external microprocessor
capacitor unit designed for cooperation with
traditional CB trip coils
• Programmable digital inputs, output relays and
LEDs, 6 inputs / 7 outputs
Documents
• Communication standards: USB, RS485
• Catalogue card
• Transmission protocols: Modbus, IEC60870-5-103 • User manual
• Recording of:
• Events - 200
• Faults – 20
• Disturbance – dynamic (1600 Hz, 7 s)
MiCOM P115
AUTONOMOUS OVERCURRENT PROTECTION RELAY
Functions: 50/51, 50N/51N, 37, 49, 46, 46BC, 50BF, 79, 74TCS
• Phase and earth fault dual-powered overcurrent • Measurements accessible via communication
protection applicable in MV substations link (no display):
• Applicable in systems where auxiliary supply • Phase currents
voltage may be interrupted or lost • Earth current
• Auxiliary protection of HV/MV transformers
Other Functions
Interaction with Circuit Breaker • Autonomous operation: dual-powered supply
• Tripping a CB when powered by current from current circuits or/and Vx auxiliary voltage
transformers only, achieved by: • 2 setting groups
• cooperation with a current coil of the circuit • Circuit breaker failure detection
breaker, an optional piece of equipment for (undercurrent criterion)
modern CB’s, • Circuit breaker control from P115 front panel
• an energy output in P115 (24VDC 0,1J) to trigger or/and via RS485
a highly sensitive trip coil, an optional piece of • Circuit breaker state monitoring
equipment for modern CB’s, • Protection blocking logic from binary inputs
• cooperation with E124 capacitor trip unit, being (decentralised bus bar protection)
a separate product by Schneider Electric (an • Programmable digital inputs (2 inputs), output
application for CB’s of older types), relays (up to 4 outputs) and LEDs (6 LCD’s)
• an energy output in P115 (12VDC 0,02mJ) to • Communication standards: USB (local),
trigger an external striker coil (Striker K1 type RS 485 (remote)
- mechanical coupling with the CB), being a • Transmission protocols: Modbus, IEC60870-5-103
E124 separate product by Schneider Electric (an • Special current output for CB tripping coil
capacitor
trip unit
application for CB’s of older types). • Recording of:
• Events - 200 with time stamping
Protections • Faults - 20
• Overcurrent, against phase-to-phase faults,
2-stage, DT or IDMT
• Earth fault, 2-stage, DT or IDMT
• Overcurrent, against asymmetry, IDMT
• Auxiliary (AUX1 and AUX2), IDMT
Documents
• Catalogue card
• User manual
MiCOM P114D
AUTONOMOUS OVERCURRENT PROTECTION RELAY
Functions: 50/51, 50N/51N
• Phase and earth fault dual-powered overcurrent • Measurements accessible via communication
protection applicable in MV substations link (no display):
• Applicable in systems where auxiliary supply • Phase currents
voltage may be interrupted or lost • Earth current
• Auxiliary protection of HV/MV transformers
Other Functions
Interaction with Circuit Breaker • Autonomous operation: dual-powered supply
• Tripping a CB when powered by current from current circuits or/and Vx auxiliary voltage
transformers only, achieved by: • Protection criteria set with DIP-switches
• cooperation with a current coil of the circuit • I/O configuration with DIP-switch
breaker, an optional piece of equipment for or MiCOM S1 software
modern CB’s, • Circuit breaker control via RS485
• an energy output in P114D (24VDC 0,1J) to • Circuit breaker state monitoring
trigger a highly sensitive trip coil, an optional • Protection blocking logic from binary inputs
piece of equipment for modern CB’s, (decentralised bus bar protection)
• cooperation with E124 capacitor trip unit, being • Programmable digital inputs (2 inputs) and
a separate product by Schneider Electric output relays (up to 4 outputs)
(an application for CB’s of older types), • Communication standards: USB (local),
• an energy output in P114D (12VDC 0,02mJ) RS 485 (remote)
to trigger an external striker coil (Striker K1 type • Transmission protocols: Modbus, IEC60870-5-103
E124
- mechanical coupling with the CB), being a • Special current output to the CB tripping coil capacitor
separate product by Schneider Electric • Recording of: trip unit
(an application for CB’s of older types). • Events - 200 with time stamping via USB
• Faults – 20 via USB
Protections
• Overcurrent, against phase-to-phase faults,
2-stage, DT or IDMT
• Earth fault, 2-stage, DT or IDMT
Documents
• Catalogue card
• User manual
MiCOM P125
DIRECTIONAL EARTH FAULT PROTECTION RELAY
Functions: 50N/51N, 67N, 32N, 59N
• Phase and earth overcurrent protection • Earth current
applicable in MV and HV stations and to protect • Residual voltage
LV and MV transformers
Protections Other Functions

• Earth fault, 3-stage, DT or IDMT • Circuit breaker control
• Earth fault, 2-stage (for Petersen coil earthed • Protection blocking logic
system) • Auxiliary output latching
• Residual overvoltage • Programmable digital inputs, output relays and
LEDs, 4 inputs, 6 outputs
• Communication standards: RS232, RS485
• Transmission protocols: Modbus, Courier,
Documents
IEC60870-5-103, DNP 3.0
• Catalogue card
• User manual

MULTIFUNCTION DIRECTIONAL LINE PROTECTION RELAY
Functions: 50/51, 50N/51N, 67, 67N, 37, 49, 46, 46BC, 50BF, 79, 32N, 27, 59, 59N, 74TCS, 81, 81R, 32F, 51V, VTS

• Universal 3-phase directional overcurrent • Four-shot autoreclose
protection, applicable in MV substations for • 8 setting groups
both incoming and outgoing feeders, as well as • Switchgear monitoring
auxiliary protection for HV • Remote and local CB control
• CB state monitoring
Protections • CB failure protection
• Overcurrent, against phase-to-phase faults, • Broken conductor detection
3-stage, DT or IDMT (P127 - directional) • Cold load pick-up logic
• Earth fault, directional, 5-stage, DT or IDMT ( 3 • Second harmonic blocking
measured and 2 derived ) • Protection blocking logic
• Wattmetric earth fault, 2-stage (for Petersen coil • Selective logic
earthed system) • Output relay testing
• Undercurrent - single stage • Output contacts latching
• Residual overvoltage (P127) • Programmable binary inputs and outputs:
• Negative phase sequence overcurrent, IDMT and • 7 x I / 8 x O
DT • extra 5 opto-insulated inputs - option
• Thermal overload with 1 thermal time constant • Extensive logic equations: 8 equations with 16
• Undervoltage, 2 thresholds (P127) operators each, of AND, OR, AN NOT, OR NOT
• Overvoltage, 2 thresholds (P127) types
• Under- and overfrequency (P127) • Measuring transformers, 0.5 class - option
• Power directional (P127) • Another RS485 port with Modbus protocol -
• Frequency rate of chance (P127) option
• Time synchronisation via IRIG-B - option
Measurements • Communication standards RS232 (local) and
• Currents and voltages RS485 (system)
Documents • Current and voltage sequences • Transmission protocols: Modbus, IEC60870-5-
• Catalogue card • Peak, average and rolling demand 103 and DNP3.0
• User manual • Thermal state in % • Recording of:
• PC simulator! • THD i TDD for measure CTs • Events - 250
• Faults - 25 (1600 Hz, window 3 s)
• Triggers - 25
MiCOM P111
UNIVERSAL OVERCURRENT PROTECTION RELAY
Functions: 50N/51N, 50/51, 67N/67YN, 26/38, 79
Application Features
• Thanks to its favourable „price vs technical • Operation in 1, 2, or 3-phase arrangement in
features” ratio, P111 may be used both in various types of networks
medium voltage and in low voltage applications • True RMS phase current value measurement
(specifically where communication facilities are within a frequency range from 10Hz to 250Hz
required). Detailed technical specifications and • Protections (see the Table below)
setting procedures for P111 are included in the • Possibility to configure protections: trip or signal
product’s user manual. • RS485 communication facility via Modbus Flush mounted version
The P111 series includes the following models: RTU protocol (option)
A, B, E, D, G, H, R. • Local or remote control of a contactor or circuit
Their features are enumerated in the Table below. breaker
• Independent programmable output relays (2 in
basic version + optionally 2 extra)
• Programmable NO output relays (P2, P3)
• Programmable binary inputs (S1-S2 and T1-T2
in basic version + optionally V1-C, V2-C, V3-C,
V4-C 35 mm DIN rail version
• LEDs to indicate protection triggering or tripping
• 4-digit LED display
• 5-button keypad to input settings and to Documents
configure protections • Catalogue card
• 2 types of case: flush or 35 mm DIN rail mounted • User manual
(R model is available in the flush version only)
MiCOM P111 Universal Overcurrent Protection Relay

Model Model
Functions Functions
A B R D E G H A B R D E G H
Time counters AUX1 and AUX2
Overcurrent I>> (DT) X X X X X X
(external protection)
Overcurrent I> (DT or IDMT) X X X X X Output relays P1 (no) and P2 (no) X X X X X X X
Overcurrent Ip> (DT or IDMT) (Overload) X X X X X Output relays P3 (no) and P4 (c/o) X X X X X
Earth fault Io> (DT or IDMT) X X X X X X 2 binary inputs: S1-S2 and T1-T2 X X X X X X X
Earth fault Io>> (DT lub IDMT) X X X X X X 2 binary inputs: V1-C and V2-C X X X X X X
Earth fault directional Ifi (0-90) X X 2 binary inputs: V3-C and V4-C X
Earth fault admittance Go> X X 2 setting groups X X X X X X X
Earth fault admittance Bo> X X RS485 communication port X X X X X X
CB/contactor control (opto-insulated

Earth fault admittance Yo> X X X X X
binary input and/or RS485)
CB failure scheme X Recording of last 3 fault trips X X X X X X X
External protection Recording of 25 events with time

X X X X X X X X X
(opto-insulated binary input) stamping feature (available via RS485)
[ Protection Relays Guide ] MV Bay Protections 12
MiCOM P132
TIME-OVERCURRENT PROTECTION RELAY
Functions: 50/51, 50N/51N, 67, 67N, ADMIT, 37, 49, 46, 50BF, 79 (3), 32N, 27, 59, 47, 27D, 59N, 32R/32(F), 81O, 81U, 81R,
51V, 26/38 (R), 48, 50S/51LR, 66, 74TCS
• Phase and earth overcurrent protections • Phase currents
applicable in MV and HV substations for both • Earth current
incoming and outgoing feeders and transformer • Phase and phase-to-phase voltages
applications • Power P, Q
• Auxiliary earth fault directional protection for HV • Energy: active, reactive
lines
Other Functions
Protections • Auto-reclosing control
• Overcurrent protection: • Circuit breaker failure detection
• DT, three-stage, separate circuits for phase • Switch on to fault protection
and residual currents, • Limit values monitoring
• IDMT, separate circuits for phase and residual • Interlocking
currents • 4 setting groups
• Thermal overload protection (thermal image) • Measuring circuit monitoring (voltage and current)
• Motor protection • Cold load pick-up logic
• Unbalance protection (negative sequence • Programmable scheme logic
current) • Freely configurable inputs / outputs / LEDs
• Under- and overvoltage • max 16 x I / 30 x O
• Short-circuit direction determination • 3 communication ports (optional)
• Ground fault direction determination - wattmetric • Communication protocols: IEC60870-103 / -101 /
and admittance Modbus / DNP 3.0 / IEC61850 (KEMA certified)
• Frequency: f, df/dt, Δf/Δt • Recording of:
• Faults – 8x200 events
Control Functions • Overload loads – 8x200 events
• Control and supervision of 3 switches • Ground faults – 8x200 events
• 6 configurable buttons • Disturbances – 8 waveforms (1kHz)
• Monitoring of extra signals and measurements • Circuit breaker monitoring
• Interlocking logic
• Over 80 pre-defined bay types
REMARK:
Voltage -dependent functions
(U>, U<, f<, f>, directionality
for I> and IN> ...) are available
for a version with measuring
voltage inputs
Documents
• Catalogue card
MiCOM P139
FEEDER MANAGEMENT AND BAY CONTROL
Functions: 50/51, 50N/51N, 50BF, 67, 67N, ADMIT, 37, 49, 79 (3), 32N, 27, 59, 47, 27D, 59N, 32R/32F (F), 81O, 81U, 81R, 51V,
26/38 (R), 48, 50S/51LR, 66, 25, 74TCS
• One-box solution in MV and HV systems - a main • Phase currents
element of dissipated change-over automatics • Earth current
• Voltages
Protections • Power P, Q, S
• Short-circuit directional against phase-to-phase • Energy: active, reactive
faults, overcurrent, 3-stage DT and 1-stage IDMT • Thermal load
• Earth fault, directional
• Under- and overfrequency f, df/dt, Δf/Δt Other Functions
• Directional power motor protection with true • Autoreclose scheme
RMS value measurement • 4 setting groups
• Unbalance, checking of negative sequence • CB failure scheme
current • Programmable inputs/outputs /LEDs
• Thermal overload with 1 thermal time constant • max. 70 x I / 23 x O or
• Motor protection features (excessive start time, • 3 communication ports (option)
limitation of number of starts etc.) • Communication protocols: IEC 60870-103 /
• Admittance earth fault -101 / Modbus / DNP 3.0 / IEC 61850 (KEMA
• Under- and overvoltage certified)
• Switch onto fault protection • Recording of:
• Synchro-check (option) • Faults – 8 x 200 events
• Overload faults – 8 x 200 events
Control Functions • Ground faults – 8 x 200 events
• Control of 6 switches • Disturbances – 8 waveforms (1kHz)
• Monitoring of 10 switches • Circuit breaker monitoring
• Monitoring of extra signals and measurements
• Mimic diagram
• More than 290 pre-defined bay types
REMARK:
Voltage -dependent functions
(U>, U<, f<, f>, directionality
for I> and IN> ...) are available
for a version with measuring
voltage inputs
Documents
• Catalogue card
• User manual
MiCOM P141 / MiCOM P142 / MiCOM P143

FEEDER MANAGEMENT RELAY
Functions: 50/51, 50N/51N, 67, 67N, ADMIT, 49, 46, 46BC, 50BF, 79, 32N, 27, 59, 47, 81O, 81U, 81R, 51V, 64N/87N, 25, 60/VTS

• Phase and earth overcurrent protections • Three-shot autoreclose – P142 i P143
applicable in MV and HV substations for both • Synchro-check – P143
incoming and outgoing feeders and transformer • 4 setting groups
applications • Switchgear monitoring
• Trip statistics
Protections • CB control
• Overcurrent, directional against phase-to-phase • CB failure protection
faults, 4-stage, DT or IDMT • Broken conductor detection
• Earth fault, two directional overcurrent • Current and voltage circuits supervision
characteristics, DT or IDMT • Cold load pick-up logic
• Admittance earth fault • Programmable inputs (256 AND/OR gates and
• Restricted earth fault (co-operation with timers), outputs and LEDs
transformer) • P141 and P142 – 8 x I / 7 x O
• Wattmetric earth fault (for Petersen Coil earthed • P143 – 16 x I / 14 x O
system) • Communication standards: RS232, RS485
• Residual overvoltage • Transmission protocols: Courier, Modbus,
• Negative sequence overvoltage IEC60870-5-103, DNP 3.0, IEC 61850
• Unbalance, directional; check of negative (KEMA certified)
sequence current • Recording of:
• Thermal overload with 1 or 2 thermal time • Events – 512
constants • Faults – 20 (window 10.5 s)
• Two stage under- and overvoltage • Quick access HOTKEY key
• Two stage under- and overfrequency
Measurements
• Phase currents
• Earth current
• Voltages
• Power P, Q, S
• Energy: active, reactive
• Thermal load
MiCOM P145
FEEDER MANAGEMENT RELAY WITH CONTROL FUNCTIONS
Functions: 50/51/67, 50N/51N/67N, YN/ADMIT, 49, 46, 46BC, 50BF, 32N, 27, 59, 59N, 74CTS, 81U/O, 81R, 32F, 51V,
64N/87N, VTS/CTS, 79, 25

• MV overhead or cable lines • Autoreclose scheme
• Auxiliary earth fault directional protection for HV • Two measuring inputs for Io
lines • Synchro-check, 2 stages
• HV / MV transformer overcurrent protection • 4 setting groups
• Switchgear monitoring
Protections • CB control
• Overcurrent, directional against phase-to-phase • CB failure protection
faults, 4-stage, DT or IDMT • Broken conductor detection
• Earth fault, directional, 4-stages, DT or IDMT • Cold load pick-up logic
• Sensitive earth fault in co-operation with core • Testing functions (DDB signals)
balanced CT, 4-stage • Measurement circuits supervision
• Restricted earth fault (differential characteristic) • Quick access HOTKEY keys
• Wattmetric earth fault (for Petersen coil earthed • Tricolour LEDs
system) • Communication standards: RS232 and RS485
• Residual overvoltage (standard), F/O (option)
• Negative sequence overvoltage • Second port for remote communication
• Directional negative sequence overcurrent, • Optional protocols: Courier,
4-stage (Is2) Modbus,IEC60870-5-103, DNP3.0, IEC61850
• Thermal overload (KEMA certified)
• Under- and overvoltage • Programmable operating scheme logic through
• Under- and overfrequency PSL Editor:
• Rate of change of frequency df/dt • P145 - max 24 x I / 32 x O
• Admittance Yo/Go/Bo • Recording of:
• Fault locator
• Events - 512
• Faults - 15
• Disturbances – 20 (max window 10.5 s, COM-
TRADE format)
Documents
• Catalogue card
• User manual
[ Protection Relays Guide ] Motor Protections 16
MiCOM P211
THREE-PHASE LV MOTOR PROTECTION RELAY
Functions: 50/51, 50N/51N, 37, 49, 46, 26/38 (P), 48, 50S/51LR
• Comprehensive protection of LV motors. • Phase currents
• Replacement for RIz, RIzc, RIzx relays. • Thermal load
• Available models: A, B, C, U - see details in the • Earth current
catalogue card
Other Functions
Protections • Easy connection of motor feeders
• Overload - thermal image: • Pre-fault indication of overload
Flush mounted version • measurement of true RMS from 10 to 250Hz • Up to 4 programmable output relays
• nominal motor current setting from 0.37 do • Up to 4 programmable binary inputs
80A (direct wiring) • RS 485 with Modbus RTU protocol
• time constants specified through tripping time
setting at 6xIn current value
• Unbalance, loss of supply and loss-of-phase
condition
• Excessive starting time
• Locked rotor
• Over temperature (with PTC sensors)
35 mm DIN rail version • Underload with time delay setting
• Short circuit
• Earth fault protection
• Self motor restart after a voltage loss
on a substation busbar
• Limitation of the number of start-ups
Documents
• Catalogue card
• User manual
MiCOM P220
INTEGRATED PROTECTION & CONTROL SOLUTION FOR MOTOR MANAGEMENT
Functions: 50/51, 50N/51N, 37, 49, 46, 26/38 (RP), 48, 50S/51LR, 66
• Comprehensive protection of LV/MV motors • Phase currents (up to 10th harmonic)
• Earth current
Protections • Thermal load
• Thermal overload with thermal image (logarithmic • Temperature
characteristic). Configuration of 3 thermal time
constants (starting, overload, cooling), 3 stages Other Functions
of thermal loading: alarm, trip and inhibition of • 2 setting groups
CB closing. • Switchgear monitoring
• Three-phase overcurrent against phase-to-phase • Trip statistics
faults; 1-stage • Analogue output
• Earth fault, 2-stage. Co-operation with core • Emergency start-up
balanced CT or three-phase CTs (Holmgreen • CB control
arrangement). • Programmable binary inputs, output relays and
• Excessive starting time. Overcurrent criteria. LEDs
Detection of the motor’s starting on the basis of • Communication standards: RS232, RS485
the starting current value or of a change in CB • Transmission protocols: Courier, Modbus,
status IEC60870-5-103
• Locked rotor while running or starting. • Recording of:
Overcurrent criteria • Events – 75
• Unbalance, loss of phase and single phasing. • Faults – 5 (1600 Hz, window 3s)
2-stage protection based on the negative • Starting current (40s)
sequence component of the current
• Loss of load. 1-stage. Undercurrent criteria.
Deactivated during start-up
• Temperature supervision. Co-operation with
6 RTD sensors (Pt, Ni, Cu) or 2 thermistors.
2-stage settings for each channel.
• Limitation of the number of successive start-ups.
Inhibition of CB closing after last unsuccessful
start-up. Separate settings for cold and hot start-
ups.
Documents
• Catalogue card
• User manual
MiCOM 225
INTEGRATED PROTECTION & CONTROL SOLUTION FOR MOTOR MANAGEMENT
Functions: 50/51, 50N/51N, 37, 49, 46, 50BF, 27, 59, 26/38 (P), 48, 50S/51LR, 66, ABS, 74TCS
• Comprehensive MV motors protection with • Phase currents (up to 10th harmonic)
power and energy measurement • Earth current
• Voltages
Protections • Power P, Q, S
• Thermal overload with thermal image. • Energy: active, reactive
Configuration of 3 thermal time constants • Thermal load
(starting, overload, cooling), 3 stages of thermal • Temperature
loading: alarm, trip and inhibition of CB closing
• Three-phase overcurrent against phase-to-phase Other Functions
faults, 1-stage • CB failure
• Earth fault, 2-stage • 2 setting groups
• Excessive starting time. Overcurrent criteria • Switchgear monitoring
• Locked rotor while running or starting. • Trip statistics
Overcurrent criteria • 2 analogue output
• Unbalance, loss of phase and single phasing. • Emergency starting
2-stage protection based on negative sequence • CB control
component of the current • Programmable inputs, outputs and LEDs
• Loss of load. 1-stage. Undercurrent criteria • Communication standards: RS232, RS485
• Temperature supervision. Co-operation with 10 • Transmission protocols: Courier, Modbus,
RTD sensors (Pt, Ni, Cu) or 3 thermistors. IEC60870-5-103
• 2-stage setting for each channel. • Recording of:
• Limitation of the number of successive start-ups. • Events – 250
Separate settings for cold and • Fault – 25
Documents
• hot start-ups. Inhibition of CB closing after last • Disturbance – 5 (1600 Hz, window 2.5s)
• Catalogue card
unsuccessful start-up. Separate settings for cold • Starting current (200s)
• User manual
and hot start-ups • Starting voltage (200s)
• Undervoltage
• Anti-backspin protection
MiCOM P241 / MiCOM P242 / MiCOM P243 (Z funkcją zab. różnicowego)

ASYNCHRONOUS & SYNCHRONOUS MOTOR MANAGEMENT RELAY
Functions: 50/51, 50N/51N, 67N, 37, 49, 46, 50BF, 32N, 27 59, 59N, 32R/32F, 81U, 26/38, 48, 50S/51LR, 66, 55, 60/VTS, 87M, 40
Protections Measurements
• Motor differential (P243) • Phase currents (up to 10th harmonic)
• Thermal overload with thermal image. 3 thermal • Earth current, voltages
time constants (starting, overload, cooling) • Power P, Q, S
• Three-phase overcurrent against phase-to-phase • Energy: active, reactive
faults, 2-stage • Thermal load
• Earth fault, directional, 2-stage, overcurrent, DT • Temperature
or IDMT Other Functions
• Residual overvoltage • 2 setting groups
• Wattmetric earth fault (for Petersen coil earthed • Switchgear monitoring
system) • Trip statistics
• Excessive starting time. Overcurrent criteria • Emergency starting
• Locked rotor while running or starting. • CB control
Overcurrent criteria • Programmable inputs (256 AND/OR gates and
• Unbalance, loss of phase and single phasing, timers), output relays and LEDs
2-stage protection based on negative sequence • 8 x I / 7 x O (P241)
component of the current • 16 x I / 14 x O (P242, P243)
• Loss of load; 2-stage, underload criteria • Communication standards: RS232/RS485
• Temperature supervision. Co-operation with 10 • Transmission protocols: Courier, Modbus,
RTD sensors (Pt, Ni, Cu); 2-stage setting for each IEC 60870-5-103, DNP3.0, IEC61850
channel (KEMA certified)
• Limitation of the number of successive start-ups. • Dual redundant Ethernet: RSTP, DHP, SHP
Separate settings for cold and • Recording of:
• hot start-ups. Inhibition of CB closing after last • Events – 512
unsuccessful start-up. Separate settings for cold • Faults – 20 (1200Hz, window 10.5s)
and hot start-ups
• Under- / overvoltage
• Anti-Backspin protection
• Out of step (monitoring of cos ϕ)
• Reverse power
• Underfrequency
• Loss of field
Documents
• Catalogue card
• User manual
[ Protection Relays Guide ] Generator Protections 20
MiCOM P341
INTERCONNECTION PROTECTION FOR EMBEDDED GENERATOR
Functions: 50/51, 50N/51N, 67, 67N, 49, 46, 50BF, 27, 59, 59N, 32R/32F, 32O, 32L, 81O, 81U, 81R, VVS, 64N/87N, 60/VTS, 25, DLR

• Small generators for LV and MV systems. Back- • 4 alternative setting groups
up protection for bigger units • Supervision of voltage and current transformer
• Interconnection line circuits
• Optional IRIG-B input for time stamp
Protections synchronisation
• Rate of frequency change (df/dt) ROCOF • Diagnostics and continuous self-monitoring
• Voltage vector shift monitoring • CB status and condition monitoring
• Directional / non-directional phase overcurrent • Communication standards: RS232, RS485
• Directional / non-directional earth fault • Optional transmission protocols: Courier,
• Sensitive directional / non-directional earth fault Modbus, IEC60870-5-103, DNP3.0
• Neutral displacement / residual overvoltage • IEC61850 (KEMA certified)
• Restricted earth fault • Optional dual redundant Ethernet: RSTP, DHP,
• Under- / overvoltage SHP
• Under- / overfrequency • Programmable scheme logic through PSL Editor
• Reverse load, overload, low forward load (MiCOM S1)
• Check synchronism • Programmable inputs (logic 256 AND/OR gates
• DLR – Dynamic Line Rating and timers, output relays and LEDs),
• 8 inputs / 7 outputs (standard)
• CLIO module
Measurements
• Extra I/O cards – option
• Phase currents
• Recording of:
• Phase and line voltage
• Events – 250
• Sequence current and voltage, neutral current
and voltage • Faults – 5
• Power P, Q, S; energy Ec, Eb • Disturbance waveforms – 20
• Peak, mean and rolling demand (window 10.5s each)
• Single and three-phase power factor
Documents
• Catalogue card
• User manual
MiCOM P342 / MiCOM P343 / MiCOM P344 / MiCOM P345

INTEGRATED NUMERICAL GENERATOR PROTECTION
Functions: 50/51, 50N/51N, 67N, 49, 46, 50BF, 27, 59, 59N, 27TN/59TN, 87 (G/T), 32R/32F, 32O, 32L, 81O, 81U, 40, 24, 51V,
21, 64N/87N, 50/27, 78, 26/38, 60/VTS, 47, 81AB, 64S (100% - Gen), CLIO, 64R, 81R, 25
• Medium and high power generators • Phase currents and voltages
• Unit protections for high-power turbine • Sequence current and voltage, neutral
generators current and voltage
• Protections for pumped-storage water power • Differential and bias currents
plants • 3rd harmonic neutral voltage
• Power: P, Q, S; energies: Ec, Eb
Protections • Temperature in °C
• Generator/Transformer differential - only
P343/4/5 models Other Functions
• Rotor earth fault protection (P391 auxiliary unit) • Frequency tracking: from 5 Hz to 70 Hz
• Interturn protection • Supervision of voltage and current
• 100% stator earth fault, 3 harmonic analysis - transformer circuits
only P343/4/5 models and 20Hz generator (P345) • Diagnostics and continuous self-monitoring
• Non-directional phase overcurrent • Communication standards: RS232, RS485
• Non-directional earth fault • Optional transmission protocols: Courier,
• Neutral displacement Modbus, IEC60870-5-103, DNP 3.0,
• Sensitive directional earth fault IEC61850 (KEMA certified)
• Restricted earth fault • Dual redundant Ethernet: RSTP, DHP, SHP
• Voltage dependent overcurrent or under- • Programmable inputs (logic - 256 AND/OR
impedance gates and timers), output relays and LEDs
• Under- / overvoltage • P342 - 8 x I / 7 x O
• Under- / overfrequency • P343 - 16 x I / 14 x O
• Reverse power, low forward load and overload • P344 - 16 x I / 14 x O
• Loss of field • P345 - 24 x I / 24 x O
• Unbalance load • Extra I/O card - option
• Overfuxing • Recording of:
• Accidental energisation at standstill - only • Events – 512
P343/4/5 models • Faults – 5
• Resistance temperature devices 10 RTDs - • Disturbance waveforms – 20
option (max. window 10.5 s)
• CLIO analogue measurements
• Frequency rate of change
• Check synchronism
Documents
• Catalogue card
• User manual
MX3EG1A
NUMERICAL MODULE FOR AUTOMATIC GENERATOR SYNCHRONISING
Functions: 25

• Frequency and voltage regulation of a • 2 setting groups
generator, permit for execution of automatic • Testing functions: LEDs, output relays
paralleling with a live or dead busbar • 5 binary inputs, 6 output relays (5 freely
• Transmitting control signal on turbine and configurable to the device functions,
generator operation (monitoring of paralleling 1 for relay diagnostics)
conditions) • 12 LEDs (8 freely configurable to perform
• CB circuit monitoring protection functions)
• Configuring binary inputs to operate on • Countes for each tripping threshold
receiving: synchronisation signals, paralleling • Local communication via PC to the front serial
requests (with live-bus Start_LB or Dead- port (with a EOC12 fibre-optic cable)
bus Start_DB), pause control, circuit breaker • Enclosure protection: IP52 for front panel
status, or other discrepancies (optional IP66)
• Application of generator and busbar phase- • Remote communication to network: via rear
to-phase voltage to 2 inputs serial port, with Lonwork™ (1.25 Mb/s) or
MODBUS (RS485)
Measurements • Recording of:
• Voltage and frequency on busbar side • Events – 32 status changes
• Voltage and frequency on generator side • Faults – 8
• Phase displacement • Disturbance waveforms: 1
• Primary voltage values (600 Hz, window 2.5s)
MX3PG2A
INTEGRATED NUMERICAL GENERATOR PROTECTION (ROTOR PROTECTION)
Functions: 64R, 27DC, 59DC, 50/51

• Rotor earth fault protection • Dedicated input for a wide range of DC voltage
measurements
Protections • Instantaneous or delayed signalling output
• Rotor earth fault detection based on injection of (alarm)
AC low voltage (50Hz) between rotor windings of • 2 setting groups to be selected from HMI,
the protected synchronous machine and ground via digital input or communication port
• Monitoring of the injected voltage • 3 binary inputs, 6 output relays
• 2 independent time thresholds to monitor the • 12 LEDs (8 freely configurable to perform
resistance of the earth fault protection functions)
• Independent time overcurrent protections • Remote communication to network: via rear
• 2 independent time delayed DC undervoltage serial port, with Lonwork™ (1.25 Mb/s)
protections • Alternative MODBUS protocol (RS485)
• 2 independent time delayed DC overvoltage • Recording of:
protections • Events – 32 status changes
• Faults – 8
Measurements • Disturbance waveforms - 1
• „Injected” voltage • Counters and LEDs
• Circulating current
• Earth fault resistance
• DC voltage
[ Protection Relays Guide ] Line Distance Protections 24

UNIVERSAL DISTANCE PROTECTION AND CONTROL UNIT (110 KV)
Functions: 50/51, 50N/51N, 67N, 49, 50BF, 79, 27, 59, 59N, 32R/32F (F), 81O, 81U, 81R, 21, 78, 26/38 (R), 25, 74TCS
• HV line protection • Phase currents
• Earth current
Protections • Phase and phase-to-phase voltages
• Distance protection: • Power: P, Q
• circular or polygonal curve • Energy: active, reactive
• 6 distance stages
• 7 direction stages Other Functions
• 8 timer stages • Auto-reclosing control:
• start-ups: overcurrent, undervoltage and unde- • (3-phase) – P433
rimpedance • (1/3-phase) – P435
• directional voltage memory • Circuit breaker failure protection
• Time-overcurrent protection: • Switch on to fault protection
• backup (active when measuring circuit failure • Limit values monitoring
is detected) • Interlocking
• DT, 4-stage, separate for phase and residual • 4 setting groups
currents • Measuring circuit monitoring (voltage and
• IDMT, separate for phase and residual currents current)
• Under- / overvoltage protection • Programmable scheme logic
• Earth fault, wattmetric protections • Programmable inputs / outputs / LEDs
• Frequency protection: f /df/dt / Δf/Δt • max 16 x I / 30 x O (P433/P435-40TE)
• Power-directional protection • max 28 x I / 46 x O (P435-84TE)
• Thermal overload protection • Analogue I/O module (option)
• Directional earth fault • 3 communication ports (option)
• PSB Power Swing Blocking • Communication protocols:
IEC 60870-103 / -101 / Modbus / DNP3.0 /
Control Functions IEC61850 (KEMA certified)
• 6 configurable buttons • Recording of:
• Faults – 8x200 signals
• Overload faults – 8x200 signals
• Earth faults – 8x200 signals
• Disturbances – 8 waveforms (1kHz)
• Circuit breaker monitoring
• Synchro-check (option)
• Power swing blocking
Documents
• Catalogue card
• User manual
MiCOM P437
NUMERICAL DISTANCE PROTECTION
Functions: 50/51, 50N/51N, 67N, 49 ,50BF, 79, 27, 59, 59N, 32R/32F (F), 81O, 81U, 81R, 21, 78, 26/38 (R), 25, 74TCS
Application • Power: P, Q
• Line protection for HV systems
Other Functions
Protections • Auto-reclosing control (1/3-phase)
• Distance protection: • Synchro-check (option)
• circular or polygonal curve • Power swing blocking
• 6 distance stages • Mutual compensation (option)
• 7 direction stages • Circuit breaker failure
• 8 timer stages • Switch on to fault protection
• start-ups: overcurrent, undervoltage and unde- • Limit values monitoring
rimpedance • Intertripping for distance protection
• directional voltage memory • Intertripping for earth fault protection
• Time-overcurrent protections: • 4 setting groups
• backup (active when measuring circuit failure • Measuring circuit monitoring (voltage
is detected) and current)
• DT, 4-stage, separate for phase and residual • Programmable scheme logic
currents • Programmable inputs / outputs / LEDs
• IDMT, separate for phase and residual currents • max 28 x I / 46 x O
• Under- / overvoltage • Analogue I/O module (option)
• Frequency protection: f, df/dt, Δf/Δt • 3 communication ports (option)
• Thermal overload protection • Communication protocols: IEC60870-
• Earth fault protection 103 / -101 / Modbus / DNP 3.0 /
IEC61850 (KEMA certified)
Control Functions • Recording of:
• 6 configurable buttons • Faults – 8x200 signals
• Overload faults – 8x200 signals
Measurements • Earth faults – 8x200 signals
• Phase currents • Disturbances – 8 waveforms (1kHz)
• Earth current • CB monitoring
• Phase and phase-to-phase voltages
Documents
• Catalogue card
• User manual
MiCOM P432
DISTANCE PROTECTION AND BAY CONTROL
Functions: 21P, 50/51, 50N/51N, 67, 67N, 46, 46BC, 50BF, 79 (3) (1), 27, 59, 51V, 78, 25, 60/VTS
• HV line protection • Phase currents
• Earth current
Protections • Phase and phase-to-phase voltages
• Distance protection: • Power P, Q
• circular or polygonal curve
• 6 distance stages Other Functions
• 7 direction stages • Auto-reclosing control (1/3-phase)
• 8 timer stages • Synchro-check (option)
• start-ups: overcurrent, undervoltage and unde- • Power swing blocking
rimpedance • Mutual compensation (option)
• directional voltage memory • Circuit breaker failure
• Time-overcurrent protections: • Switch on to fault protection
• backup (active when measuring circuit failure • Limit values monitoring
is detected) • Intertripping for distance protection
• DT, 4-stage, separate for phase and residual • ntertripping for earth fault protection
currents • 4 setting groups
• IDMT, separate for phase and residual currents • Measuring circuit monitoring (voltage and
• Under- / overvoltage current)
• Frequency protection: f, df/dt, Δf/Δt • Programmable scheme logic
• Thermal overload protection • Programmable inputs / outputs / LEDs
• Earth fault protection • max 28 x I / 46 x O
• Analogue I/O module (option)
Control Functions • 3 communication ports (option)
• Control of 6 switches • Communication protocols: IEC60870-103 / -101
• Monitoring of 10 switches / Modbus / DNP 3.0
• Monitoring of extra signals and measurements • Recording of:
• Mimic diagram • Faults – 8x200 signals (1 kHz)
• Interlocking logic • Overload faults – 8x200 signals
• More than 290 configurable bay types • Earth faults – 8x200 signals
• Disturbances – 8 waveforms (1kHz)
• Circuit breaker monitoring
Documents
• Catalogue card
MiCOMho P443 With sub-cycle technology !!!

FAST MULTIFUNCTION DISTANCE PROTECTION
Functions: 21P/21N, 50/27, ΔI/ΔV, 68, 78, 85, 50/51/67, 79, 25, 46, 46BC, 50N/51N/67N,
67SEF, 49, 27, 59, 59N, 50BF, CTS/VTS, 81U/O/R, FL

• Fast distance protection for HV / LV overhead or • Broken conductor detection
cable lines • Measuring circuit monitoring (voltage and
current)
Protections • Parallel line compensation
• Single- (P443) and/or 3-phase tripping logic • Zone 1 extension
• Single- and/or 3-phase autorecloser with • Load blinder characteristics
optional synchro-check • Stub bus protection
• 5 zones of protection • Thermal overload
• Delta directional comparison ΔI/ΔU • Circuit breaker failure
• Mho or quadrilateral (polygon) characteristics • Breaker condition monitoring
• Loss of load protection • 4 setting groups
• Power swing alarm or blocking • High break contacts (10A/220V DC)
• Directional / non-directional phase overcurrent as option (max 8)
• Directional / non-directional earth fault • InterMiCOM64 teleprotection - option
• Directional / non-directional negative sequence • Direct transmission of binary signals
overcurrent (max 8 per channel)
• Residual voltage protection • Support for 3-terminal applications
• Under- / overvoltage • 1 or 2 FO channels (ST standard)
• Switch on to fault and zone-selectable trip on • Quick access HOTKEY keys
reclose protection • Optional transmission protocols: Courier,
• Out of step IEC60870-5-103, DNP 3.0, IEC61850 + RS485
(Courier / IEC-103)
Measurements • Dual redundant Ethernet: RSTP, DHP, SHP
• Comprehensive measurements • 2nd port for remote communication
• Instantaneous, I, U, P, Q, ... • Programmable scheme logic through PSL Editor
• Time integrated, demands (MiCOM S1)
• Diagnostics of connections for teleprotections • P443 A: 16 x I / 24 x O - A
• P443 B: 24 x I / 32 x O - B
• Extra I/O cards - option
• Recording of:
• Fault location
• Events - 512
• Faults - 15
• Disturbance waveforms - 20
(max window 10.5 s)
Documents
• Catalogue card
• User manual
MiCOMho P446 Interoperates with 2 circuit breakers

HIGH PERFORMANCE DISTANCE PROTECTION
Functions: 21P/21N, 50/27, ΔI/ΔV, 68, 78, 85, 50/51/67, 79, 25, 46, 46BC, 50N/51N/67N, 67SEF, 49, 27, 59, 59N, 50BF, CTS/
VTS, 81U/O/R, FL
Application • Broken conductor detection

• Fast distance protection for HV / LV overhead or • Measuring circuit monitoring (voltage and
cable lines interacting with2 circuit breakers current)
• 1.5- and 2-CB systems • Parallel line compensation
• Zone 1 extension
Protections • Load blinder characteristics
• Single- (P443) and/or 3-phase tripping logic • Stub bus protection
• Single- and/or 3-phase autorecloser • Thermal overload
• 5 zones of protection • Circuit breaker failure
• Delta directional comparison ΔI/ΔU • Breaker condition monitoring
• Mho or quadrilateral (polygon) characteristics • 4 setting groups
• Loss of load protection • High break contacts (10A/220V DC) as option
• Power swing alarm or blocking (max 8)
• Directional / non-directional phase overcurrent • InterMiCOM64 teleprotection - option
• Directional / non-directional earth fault • Direct transmission of binary signals (max 8
• Directional / non-directional negative sequence per channel)
overcurrent • Support for 3-terminal applications
• Residual voltage protection • 1 or 2 FO channels (ST standard)
• Under- / overvoltage • Quick access HOTKEY keys
• Switch on to fault and zone-selectable trip on • Optional transmission protocols: Courier,
reclose protection IEC60870-5-103, DNP 3.0, IEC61850 + RS485
• Out of step (Courier / IEC-103)
• Dual redundant Ethernet: RSTP, DHP, SHP
Measurements • 2nd port for remote communication
• Comprehensive measurements • Programmable scheme logic through PSL Editor
• Instantaneous, I, U, P, Q, ... (MiCOM S1)
• Time integrated, demands • P446 - 32 x I / 32 x O
• Diagnostics of connections for teleprotections • Recording of:
• Fault location
Other Functions • Events - 512
• Faults - 15
• Disturbance waveforms - 20 (max window 10.5 s)
[ Protection Relays Guide ] Line Differential Protections 29
MiCOM P521
CURRENT DIFFERENTIAL PROTECTION
Functions: 87L, 87T, 50/51, 50N/51N, 46, 46BC, 50BF, 37, 74TCS

• Current differential protection for MV/HV • Direct optical fibre links
overhead or cable lines • 850nm – Multi-mode
• Line - transformer application • 1300nm – Multi-mode
• 1300nm – Multi-mode
Protections • Suitable for interface to multiplexed systems
• Biased Differential Protection • Adjustment to electrical standard with P590
• Low impedance modules
• 3-phase tripping • EAI232 modems
• Intertripping both Direct and Permissive • Standard telephone lines
• Immune to line charging inrush currents • EAI485 / EAI422 / EAI 530 modems
• Selectable inrush restrain • TD32 type - leased lines
• Time delayed overcurrent protection • mDSL type
• 4-stage phase overcurrent • Wire connection with fast Campus Baseband
• 4-stage earth fault modems (56/64kbit/s max up to 18 km)
• Thermal overload • CB failure
• Broken conductor detection • Trip circuit supervision
• Negative sequence overcurrent • CB condition monitoring
• Undercurrent • Optional remote transmission protocols:
Modbus, IEC60870-5-103
Measurements • Local communication: RS232
• True RMS measured values • Commissioning tests
• Phase currents • Recording of:
• Neutral currents • Events – 250
• Sequence currents • Faults – 25
• Bias and differential currents • Disturbance waveforms – 5 (1600Hz, window
• Remote currents 3s, COMTRADE record format)
• Peak and rolling demand values
• Communication statistics
Documents
• Catalogue card
• User manual

HIGH-SPEED CURRENT DIFFERENTIAL UNIT PROTECTION
Functions: 87L, 50, 51, 50N, 51N, 46, 46BC, 49, 50BF

• Differential protection of HV / LV overhead • Dual redundant communications
or cable lines • Propagation delay compensation
• Protection of 2- or 3-terminal overhead • Setting of a transformer connection group
or cable lines • Direct and permissive intertripping via a
• Line - transformer application communication channel
• Binary signal transfers for intertripping • Circuit breaker failure
of distance protections • Autoreclose function for P542
MiCOM P541_J
• 4 setting groups
Protections • Communication with optical fibre (point - point)
• Current differential: phase current compensation, or with multiplexed systems
CT ratio correction, vector compensation, • InterMiCOM64 teleprotections
transformer inrush restraint (2nd harmonic) • Binary signal transfers - max 8 signals per
• Directional / non-directional phase and earth channel (max 16 signals per 2 channels)
fault overcurrent • Optional transmission protocols: Courier,
• Thermal overload Modbus, IEC60870-5-103, DNP 3.0
• Broken conductor detection • Programmable scheme logic through PSL Editor
(MiCOM S1)
Measurements • P541 - 8 x I / 7 x O
MiCOM P542_J • Local and remote currents • P542 - 16 x I / 14 x O
• Sequence currents • Recording of:
• Bias and differential currents • Fault location
• Thermal state • CB diagnostics
• Propagation delay • Error statistics for active channels
• Events – 512
• Trips – 5
• Disturbance waveforms – 20 max window 10.5s,
COMTRADE record format
Documents
• Catalogue card
• User manual

HIGH-SPEED CURRENT DIFFERENTIAL UNIT PROTECTION
Functions: 50/51, 50N/51N, 67, 67N, 49, 46BC, 50BF, 79, 87L, 21P/21N, 27, 68, 78, 85, 59, 59N, CTS/VTS, 25, 81O/U, 81R, FL

• Differential protection of HV / LV overhead or • Dual redundant communications
cable lines with optional distance protection • Propagation delay compensation
functions • Capacitive current compensation
• Protection of 2- or 3-terminal overhead or cable • Setting of a transformer connection group
lines • Direct and permissive intertripping via a
• Line - transformer application communication channel
• Applicable in SDH/SONET synchronous • Circuit breaker failure MiCOM P543/4/5/6_K
networks • Autoreclose with synchro-check
• Teleprotection functions - 2 groups
Protections • Supervision of current and voltage measuring
• Two CB’s configuration (P544, P546) circuits
• Current differential: phase current compensation, • 4 setting groups
CT ratio correction, vector compensation, • High break outputs (10A / 220V DC) as option
transformer inrush restraint (2nd harmonic) (max 8 otputs) - P543/4/5/6
• Directional / non-directional phase and earth • Communication with optical fibre (point - point)
fault overcurrent or with multiplexed systems
• Directional wattmetric earth fault • InterMiCOM64 teleprotections
• Thermal overload • Binary signal transfers - max 8 signals per
• Sensitive earth fault channel (max 16 signals per 2 channels)
• 5-zone distance protection - option • Optional transmission protocols: Courier,
• Power swing blocking Modbus, IEC60870-5-103, DNP 3.0,
• Out of step protection IEC 61850 + RS485 (KEMA certified)
• Broken conductor detection • Dual redundant Ethernet: RSTP, DHP, SHP
• Programmable scheme logic through PSL Editor
Measurements (MiCOM S1)
• Local and remote currents • P543/4/5/6 - min. 16 x I / 14 x O
• Sequence currents • Extra I/O modules
• Power and energy • Recording of:
• Bias and differential currents • Fault location
• Thermal state • Error statistics for active channels
• Propagation delay • Events – 512
• Faults – 15
• Disturbance waveforms – 20 max window
10.5s, COMTRADE record format
Documents
• Catalogue card
• User manual
[ Protection Relays Guide ] Differential Protections for Transformers, Generators and Motors 32
MiCOM P532
LINE DIFFERENTIAL PROTECTION AND CONTROL DEVICE
Functions: 87L, 50/51, 50N/51N, 50BF, 67, 67N, ADMIT, 49, 79 (3), 32N, 27, 59, 47, 27D, 59N, 32R/32F (F), 51V, 26/38 (R), 46, 25, 74TCS, CTS/VTS, FL
• Selective and sensitive protection of overhead • Differential and restraining current
and cable lines • Angles between local and remote currents
• One-box solution with optional bay controller (separate for each of the 3 phases)
in MV systems • Local and remote phase currents
• Earth current
Protections • Voltages
• Line current differential • Power P, Q, S
Option with graphic HMI • Directional phase-phase overcurrent, 3-stage • Energy: active, reactive
IDMT and 1-stage DT • Thermal state
• Directional earth fault
• Directional, active and reactive power Other Functions
• Unbalance, check of the negative sequence • Autoreclose function
current • 4 setting groups
• Thermal overload with 1 thermal time constant • CB failure scheme
• Admittance earth fault • Circuit breaker monitoring
• Under- / overvoltage • Programmable inputs / outputs / LEDs
• Switch onto fault protection • Max of 46 x I / 30 x O
• Synchro-check (option) • 3 communication ports (option)
• Communication ports: IEC 60870-103 / -101/
Control Functions (IED with graphic HMI) Modbus / DNP 3.0 / IEC 61850 (KEMA certified)
• Control of 6 switches (IED with graphic HMI) • Recording of:
• Monitoring of 10 switches (IED with graphic HMI) • Faults – 8x200 events
Option with text HMI • Control and monitoring of 3 switches (IED with • Overload faults – 8x200 events
text HMI – 6I6O module required) • Ground faults – 8x200 events
• More than 290 pre-defined bay types • Disturbances – 8 waveforms (1kHz)
• Check of extra signals and measurements
• Mimic diagram
[ Protection Relays Guide ] Differential Protections for Transformers, Generators and Motors 33

UNIVERSAL DIFFERENTIAL RELAY
Functions: 50/51, 50N/51N, 49, 87 (T), 81O, 81U, 81R, 24, 64N/87N, 26/38 (R), 74TCS, 50BF
• Differential protection with supplementary • Differential and restraining currents
functions for transformers, motors and • Phase currents (separate for each phase and
generators each end of the protected unit)
• Earth current (separate for each end of the
Protections protected unit)
• Differential: • Phase shifts between phases
• amplitude and vector group matching • Phase shifts between the same phases of
• zero-sequence current filtering for user-selec- different ends in the protected unit
ted winding(s) • Voltages (P632/3/4)
• inrush restraint (2nd harmonic)
• overfluxing restraint (5th harmonic) Other Functions
• saturation discriminator • Limit values monitoring
• MiCOM P631: 2 ends • 4 setting groups
• MiCOM P632: 2 ends • Programmable scheme logic
• MiCOM P633: 3 ends • Programmable inputs / outputs / LEDs
• MiCOM P634: 4 ends • Analogue I/O module (option)
• Restricted earth-fault, separate for each end of • 3 communication ports
the protected unit (P632/3/4) • Communication protocols: IEC60870-103 / -101
• Overcurrent: DT or IDMT, 3-stage, separate for / Modbus / Courier / DNP 3.0 / IEC61850
phase and residual currents (KEMA certified)
• Io calculated or measured (P632/3/4) • Recording of:
• Thermal overload (for 2 ends) • Disturbances – 8 waveforms (1kHz)
• Frequency: f, df/dt, Δf/Δt (P632/3/4) • Overload faults – 8x200 signals
• Overfluxing U/f • Faults – 8 x 200 signals
Control Functions
• Control and monitoring of 3 switches
• 6 configurable function keys
• Check of extra signals and measurements
• More than 80 pre-defined bay types
•
Documents
• Catalogue card
• User manual
[ Protection Relays Guide ] Voltage Protections 34
MiCOM P132
VOLTAGE PROTECTION WITH LOAD SHEDDING SCHEME
Functions: 27, 59, 47, 27D, 59, 59N, 81O, 81U, 81R, Δf/Δt

• Voltage and frequency protection for applications • Limit values monitoring
in voltage measurement bays of a MV substation • 4 setting groups
• Measuring circuit supervision
Protections • Programmable scheme logic
• Phase under- / overvoltage • Programmable inputs / outputs / LEDs
• Under- / overvoltage for positive sequence (U1) • (4 x I / 8 x O) or (4 x I / 14 x O) or (10 x I / 11 x O)
• Under- / overvoltage for negative sequence • 3 communication ports (option)
voltage (U2) • Communication protocols: IEC 60870-5-103 /
• Overvoltage for zero-sequence (Uo) -101 / Modbus / DNP 3.0 / IEC 61850 (KEMA
• Monitoring of phase-to-phase and/or phase certified)
voltages • Recording of:
• Frequency (4-stage) • Disturbances - 8 waveforms (1kHZ)
• with change of frequency rate df/dt
• with supervision of mean rate of frequency
change (Δf/Δt)
Measurements
Documents • Phase voltages
• Catalogue card • Phase-to-phase voltages
• User manual • Positive, negative and zero-sequence voltages
MiCOM P921
VOLTAGE PROTECTION RELAY
Functions: 27, 59, 59N

• Comprehensive voltage protection • Available configurations:
• 3 (phase-neutral)
Protections • 2 (phase-phase + residual)
• Undervoltage, 3-stage, IDMT and DT • 2 (phase-neutral + residual)
• Overvoltage, 3-stage, IDMT and DT • 1 (phase-phase + residual)
• Residual overvoltage, 3-stage, IDMT and DT • 1 setting group
• CB state monitoring
Measurements • Blocking logic
• Voltages • Programmable 2 binary inputs, 4 output relays
• Frequencies and LED diodes
• Output contact latching
• Communication standards: RS232, RS485
• Transmission protocols: Courier, Modbus,
IEC60870-5-103
Documents
• Catalogue card
• User manual
[ Protection Relays Guide ] Voltage Protections 35

VOLTAGE PROTECTION WITH LOAD SHEDDING SCHEME
Functions: 27, 59, 47, 27D, 59, 59N, 81O, 81U, 81R, ΔU/Δt

• Comprehensive voltage protection with Load • Available configurations:
Shedding Scheme • 3 (phase-neutral)
• 2 (phase-phase + residual)
Protections • 2 (phase-neutral + residual)
• Undervoltage, 3-stage, DT and IDMT • 1 (phase-phase + residual)
• Overvoltage, 3-stage, DT and IDMT • 2 setting groups
• Zero-sequence overvoltage, 3-stage, DT and • CB state monitoring
IDMT • CB supervision
• Negative sequence overvoltage, 2-stage, DT and • Blocking logic
IDMT • Programmable 5 binary inputs, 8 output relays
• Positive sequence undervoltage, 2-stage, DT and LED diodes
and IDMT • Output contact latching
• Under- / overfrequency, 6-stage • Communication standards: RS232, RS485
• 6-stage df/dt (P923 only) • Transmission protocols: Courier, Modbus,
• ΔU/Δt (P923 only) IEC60870-5-103
• Recording of:
Measurements • Events – 250
• Voltages • Faults – 250 (1600 Hz, window 2.5s)
• basic harmonic
• average values
• peak values
• Frequencies
Documents
• Catalogue card
• User manual

VOLTAGE & FREQUENCY PROTECTION RELAY
Functions: 27, 59, 81O, 81U, 81R, 60/VTS, 81AB
• All application where accurate frequency • Voltages
monitoring is required for system stability • Frequencies
• Load shedding scheme and autoreclose
functionality afterwards Other Functions
Protections • Load shedding scheme, 6-stage
• Under- / overfrequency • Trip statistics
• 6-stage, 4 measuring criteria: • Programmable inputs (logic 250 AND/OR gates
• check of frequency, time-delayed and timers), output relays and LED diodes
• change of frequency rate df/dt, time-delayed • P941: 8 x I / 7 x O
• frequency supervision vs. change of frequency • P943: 16 x I / 14 x O
rate f+df/dt, instantaneous • Communication standards: RS232, RS485
• frequency supervision vs. mean rate of frequ- • Another RS232/RS485 port as an option
ency change f+Δf/Δt, instantaneous • Transmission protocols: Courier, Modbus,
• Abnormal operation of a generator; check of IEC60870-5-103, DNP 3.0
frequency changes within a timeframe, in 4 • Recording of:
bands • Events – 512
• Under- / overvoltage, 2-stage. IDMT and DT. • Faults – 20 (1200Hz, window 10.5s)
• Extra I/O modules Documents
• 6-stage autoreclose after load shedding scheme • Catalogue card
• User manual
[ Protection Relays Guide ] Busbar Protections 36
MiCOM P741 (CU) / MiCOM P742 (PU) / MiCOM P743 (PU)

NUMERICAL BUSBAR PROTECTION RELAYS WITH CB FAILURE PROTECTION - DISSIPATED
Functions: 87BB/P, 87BB/N, 87CZ, 50/51, 50N/51N, CTS, 50BF

• Busbar and CB failure protections applicable • Possibility to configure up to 8 zones and 28
in 110/220/400 kV power transmission and Peripheral Units per a single Central Unit (P741)
distribution network substations • Distributed and centralised architecture in cubicles
• Suitable for industrial network and power plant • Fast fault clearance (a typical tripping time of 13 ms)
substations (including reversible generators) • Dynamic adjustments to changes in substation
MiCOM P741
Central Unit • Substation topologies: 1 ½ and 2 CBs, mesh topology
corner • Innovative algorithms for CT saturation detection
• Possibility to accommodate different CT classes,
Protections with CT differentiating up to 40 times
• Busbar bias differential - P741 (CU) • Available testing functions
• Check zone protection - P741 (CZ) • Optional transmission protocols: Courier, IEC 60870-
• Circuit breaker failure protection (general 3-pole 5-103, IEC 61850 (P741, P743)
trip) - P741 (CU) • Dual redundant Ethernet: RSTP, DHP, SHP
MiCOM P742 • Dead zone protection (a short zone between CB • Another RS232/RS485 port (Courier only) for P741,
Peripheral Unit
and CT) P743
• Non-directional overcurrent protection: • Programmable scheme logic through PSL Editor
• P742/P743 (MiCOM S1)
• phase fault (2-stage) • P741 - 8 x I / 8 x O
• earth fault (2-stage) • P742 - 16 x I / 8 x O
• Circuit breaker failure protection (single- and • P743 - 24 x I / 21 x O
3-pole retrip) - P742/3 • Recording of:
MiCOM P743 Events – 512
Peripheral Unit Measurements Faults – 5
• Central Unit (P741) Disturbance waveforms – 20
• differential current: Idiff/phase/zone • 10.5s for P742/P743
• bias current: Ibias/phase/zone • 1.2s for P741
• zone check: Idiff/zone
• Peripheral Units (P742/P743)
• phase currents: IL1, IL2, IL3
• earth current: Io
• frequency
Documents
• Catalogue card
• User manual
[ Protection Relays Guide ] Busbar Protections 37
MiCOM P746
NUMERICAL BUSBAR PROTECTION RELAYS WITH CB FAILURE PROTECTION - CENTRALISED
Functions: 87BB/P, 87BB/N, 87CZ, 50/51, 50N/51N, CTS, VTS, 50BF

• Busbar and CB failure protections applicable • Possibility to configure up to 2 systems
in 110/220/400 kV power transmission and • P746 in 1-box mode solution can accommodate
distribution network substations up to 6 CTs, 6 breakers, 12 isolators
• Suitable for industrial and railway networks as • P746 in 3-box mode solution can accommodate
well as for power stations up to 18 CTs, 18 breakers, 36 isolators 1-box mode
• H3 - H5 substations (110kV) • Fast fault clearance (a typical tripping time
of 12 ms HBC or 17 ms SC)
Protections • Dynamic adjustments to changes in substation
• Busbar bias differential topology
• Check zone protection (CZ) • Innovative algorithms for CT saturation detection
• Circuit breaker failure protection (general 3-pole • Optional voltage criteria
trip) • Tricolour LED diodes, function keys x 10 and
• Dead zone protection (a short zone between CB HOT KEY x 2
and CT) • Available testing functions
• Non-directional overcurrent protection: phase • Software for switch status monitoring and real-
fault (2-stage) and earth fault (2-stage) time measurements (Remote HMI)
• Unbalance load (2-stage) • Optional transmission protocols:
• Supervision of voltage and current circuits Courier, IEC60870-5-103, DNP 3.0,
IEC 61850 (KEMA certified)
Measurements • Dual redundant Ethernet: RSTP, DHP, SHP 3-box mode
• Differential and bias current per phase and per • Cyber Security on the NERC norm (one per phase)
zone/system • Another independent RS232/RS485 port

• Differential current per phase for check zone (Courier only)
• Phase currents: L1, L2, L3 • Programmable scheme logic through PSL Editor
• Sequence current (MiCOM S1)
• Voltages • P746 - max 40 x I / 32 x O
• Frequency • Recording of:
• Events - 512
• Faults - 5
• Disturbance waveforms - max 10.5s, single
disturbance (min. 50 records, 1.5s - memory
of 75s)
Documents
• Catalogue card
[ Protection Relays Guide ] MV Changeover Automation 38

MV CHANGEOVER DEVICES
Hardware
• Changeover scheme utilises programmable logic On the basis of the state of a bus coupler CB,
of MiCOM P132 (or MiCOM P139) relay. For the the P13x selects a type of back-up supply con-
relays description see page 12 and 13 of this figuration. Accordingly, a changeover scheme
Guide. mode and a sequence of control operations are
chosen automatically. The device may be pro-
Principles of Operation grammed to operate both in 1-shot changeover
Two scheme configurations are possible: scheme and in return changeover scheme.
• Information on primary voltage interruption is The scheme can be blocked by:
sent from voltage relays (e.g. MiCOM P921) • external signals, sent to binary inputs from
located in measuring bays to binary inputs of other controllers or functional relays, located in
a P13x relay, which initiates the course of the other bays
changeover scheme. During the course of the • internal signals, sent from an integrated facility
scheme the P13x performs several control which monitors the switching state, or after a
operations (opening and closing CBs), using successfully completed scheme
its auxiliary output relays and binary inputs. A • a system of higher level.
manner to initiate the scheme can be selected by • If no protection relay is required in a bus
a user out of the following options: coupler bay, the P13x utilises its binary inputs
• on energising of a binary input of the device, and output relays only, whereas its protection
assigned to an output relay of undervoltage facilities are disabled.
facility in the measuring bay • There are 2 MiCOM P13x devices installed in
• on tripping of a protection relay in a transfor- parallel in 2 feeder bays. In such a case the
mer bay, having confirmed a change of CB relays perform several protection functions for
Documents state in the primary supply bay feeder lines, apart from the changeover scheme
• Catalogue card • remotely, on sending a system command. features described above.
• User manual
MiCOM P841 Interoperates with 1 or 2 circuit breakers

MULTIFUNCTION LV LINE TERMINAL PROTECTION AND CONTROL IED
Functions: 79, 25, 50/51/67, 50N/51N/67N, 51N/67N/SEF, 67/46, 46BC, 49, 27, 59, 59N, 50BF, CTS/VTS, 81U/O/R, FL
• Back-up protection for HV / LV overhead and • Broken phase conductor detection
cable lines • Voltage and current transformer supervision
• Independent single- / 3-pole auto-reclosing unit • Thermal overload
dedicated to single breaker applications (P841A) • Circuit breaker failure protection
or to 2 breaker applications (P841B) • Breaker condition monitoring
Protections • High speed, high break contacts (10A/220V
• Single- / 3-pole auto-reclosing scheme DC) available as an option (max 8)
• Directional earth fault • InterMiCOM64 teleprotection - option
• Sensitive directional earth fault SEF • Direct transmission of binary signals
• Loss of load • Support for 3-terminal applications
• Directional / non-directional overcurrent • 1 or 2 FO channels (ST standard)
• Directional / non-directional negative sequence • Quick access HOTKEY keys
overcurrent • Optional transmission protocols: Courier,
• Residual voltage protection IEC60870-5-103, DNP 3.0,
• Under- / overvoltage IEC61850 + RS485 (Courier / IEC-103)
• Switch-on-to-fault and trip-on-reclose protection • Dual redundant Ethernet: RSTP, DHP, SHP
• Out of step • 2nd port for remote communication
• Programmable scheme logic through PSL Editor
Measurements (MiCOM S1)
• Comprehensive measurements • P841 - 24 x I / 32 x O
Documents
• Instantaneous, I, U, P, Q ... • Recording of:
• Catalogue card
• Time integrated, demands • Fault location
• User manual
• Energy • Events - 512
• Faults - 15
• Disturbance waveforms - 20
(max window 10.5s)
[ Protection Relays Guide ] Accessories 39
MiCOM E124
CAPACITOR TRIP UNIT
Application Other Features

• Suitable for interaction with automatic relays of • Internal monitoring of current
P115 and P124 types • Possibility to operate with trip coils at 24V, 110V
• Back-up for auxiliary supply voltage for digital and 230V levels
protection relays in case of a short-term loss of • Test button switches allow discharge of each of
voltage supply capacitor banks
• Applicable for trip coils in 110kV bays • Case of 10TE Midos type
(e.g. 110/MV transformer bays) • Flush mounting, available adapters for wall
mounting
Key Features • Operating temperature range: -25°C to +55°C
• The cumulated energy (max 300V / 118J)
remains over 8 days without recharge
• Possibility to energize 2 different tripping circuits
(max 2 x 59 J)
• Load status indicators
Documents
• Catalogue card
MiCOM P891
CIRCUIT BREAKER TRIP / CLOSE MODULE

• Direct control of CB tripping and closing • Suitable for synchro-check modules and auto-
• Co-operation with MiCOM relays and P991 test reclosing facility
blocks • Available for ring- and pin-terminals
• Pushbutton covers are provided to prevent
Key Features inadvertent operation of pushbutton switches
• Pushbutton switches • Case of 10TE Midos type
• LED indicators for device open and close
indication
• Universal power supply for LED indication circuit
• Dedicated output contacts per pushbutton,
direct wiring with tripping, controlling and
indicating circuits
Documents
• Catalogue card
[ Protection Relays Guide ] Accessories 40

TEST BLOCKS

• Direct access to protective automation • Customer’s configuration defined at the ordering
equipment and measuring relays stage
• Breaking of measuring and tripping circuits • Screw terminals (pod M4)
• Mechanical polarisation of the plug
Key Features • Case of 10TE Midos type
• Factory configurable to the customer’s • Flush mounting, available adapters for wall
requirements (available 14 circuits) mounting
P991
• Sequential shorting / breaking of circuits • Operating temperature range: -25°C to +55°C
• Automatic shorting of current circuits
• One test plug applicable for all possible
configurations of the socket
• Available single-finger (P993) or multi-finger
(P992) test plugs
P992
P993
Documents
• Catalogue card

COMMUNICATION INTERFACE UNITS FOR MULTIPLEXERS
Applications Other Features

• Conversion of fibre-optic to electrical standard • Diagnostic and testing functions configurable
for multiplex devices (MUX) with microswitches
• Communication interface for current differential • Maximum distance between a protection relay
line protections (MiCOM P54x and P52x) and the P59x communication interface up to
1km with the use of 850nm MM fibre-optic cable
Key Features • P59x interfaces should by installed as close to
• MiCOM P591 - converts fibre-optic 850 nm MM PCM multiplexers as possible
standard to electrical standard of G.703.1 type • Fibre-optic links through BFOC 2.5 (ST)
(64kbit/s) connectors
• MiCOM P592 - converts fibre-optic 850 nm MM • MiCOM 10TE case suitable for flush mounting
standard to electrical standard of V.35 type
• MiCOM P593 - converts fibre-optic 850 nm MM
standard to electrical standard of X.21 type
• Zero-sequence overvoltage
[ Protection Relays Guide ] Accessories / Services 41
MiCOM P594
GPS SYNCHRONIZING UNIT

• Real time synchronisation in IRIG-B standard • Parameter settings input by means of LCD front
(in modulated or un-modulated mode) for panel
protections, recorders or RTUs within a whole • Available 8 LED indicator diodes
substation / switchyard • Available 2 „watchdog” contacts
• Real time synchronisation for protections, • 4 fibre-optic outputs (for P543/4/5/6 )
recorders or RTUs within a whole substation / • 1 IRIG-B input (modulated), BNC type
switchyard through opto input (e.g. Px20 Phase2 • 1 IRIG-B input (non-modulated), RS422 type
V11, Px30, Px40 series) • 4 output relays (configurable)
• Sampling synchronisation for current-differential • Pulse-per-minute (PPM) or Pulse-per-hour (PPH)
protection relays of P543/4/5/6 type installed functionality
in synchronous optical networks SDH/SONET • Module supplied with antenna and cable (25m
(fibre-optic link) or 50m)
• Sampling synchronisation for CVCOM Merging • Universal auxiliary voltage supply Vx AC/DC
Units linked with non-conventional instrument • Flush unit casing in MiCOM 20TE standard
transformers (NCITs) via IEC61850-9-2 protocol.
• Sampling synchronisation for Phasor
Measurement Units
Documents
• Catalogue card
Services
• The services offered constitute a substantial Repairs
part of business activities run by Schneider • Equipment reparations
Electric Energy Poland Sp. z o.o. in the area of • Lending of replacement products for the repair
Protections and Systems. Being a global player period
in the sectors of energy generation, transmission • Efficient troubleshooting
and distribution for power industry and industrial • Modernisation of legacy solutions
power plants, we are offering a servicing scheme
customised to meet individual customers’ Installation Retrofit
requirements. • Maximum efficiency at minimum costs
• Maintenance and Technical Support
Consulting and Expertise • Technical aid and assistance on a customer’s
• Technical support site
• Application counselling • Spare parts stock
• Assistance in selection, input and modification of • Maintenance of equipment
settings
Spare Parts
Installation and Commissioning • Offer of supplies of necessary parts and
• A team of professionals trained in handling our components
products installed on sites
Training Sessions
• Related to products
• Related to commissioning operations
• As per customer’s requests
[ Protection Relays Guide ] MV Network Automation / Easergy Range of Products 42
Easergy T200I
MV AND MV/LV SUBSTATION CONTROL UNIT WITH TELECONTROL INTERFACE TO SCADA SYSTEMS

• 4 to 36kV cable networks • Remote control and parameter setting with a
• MV network management built-in Web server
• Collaboration with standard MV switchgears (e.g. • Remote access to data in parallel to the control
RM6 etc. ) system by means of GSM, GPRS, Ethernet,
• Remote monitoring of network parameters PSTN transmission links
• Monitoring of external IEDs via Modbus protocol • Cooperation with L500 system for Easergy
• Cooperation with external, directional fault equipment
passage indicators • Monitoring of battery availability
• Supervision and control over the equipment • Power supply self-check
installed in a substation • Transmission of alarms to SCADA system
• Power supply switchover automation (internal • Selection of local and remote mode of operation
logic schemes) • 6 binary inputs for general utilisation
• 1 binary input for internal FPI reset
Functions & Measurements • 1 output relay for external FPI reset
• Measurements of work currents on cable lines • 1 output relay for launching an external flashing
• Measurements and indication of fault currents on indicator (visibility 50m, a flash every 1s )
cable lines • Automatic selectioniser
• Measurements and control of voltages on MV or • Automatic changeover switch with generator
LV side start-up function
• Paralleling
Communication • Archives of events and measurements
• Available 3 communication ports: 2 remote as • 5 types of counters
per options and 1 of Ethernet type • In-built fault current detector
• Remote network: radio, PSTN, GSM/GPRS, • Control of 4, 8 or 16 switches at a substation
Ethernet • Dedicated CTs
• Local network: RS485 Modbus. Communication • Unified connector for measuring circuit
protocols: IEC870-5-101 and IEC870-5-104, connections
DNP3. The angles between local and remote
currents (separately for each of the 3 phases)
• Local and remote phase currents
• Earth current
• Voltages
• Power P, Q, S
• Energy: active, reactive
• Thermal load
[ Protection Relays Guide ] MV Network Automation / Easergy Range of Products 43
Flair200C
DIRECTIONAL INDICATOR OF FAULT PASSAGE WITH RTU FUNCTIONALITY
AND REMOTE COMMUNICATION FOR CABLE NETWORKS

• Detection of earth fault current passages in • Resetting of fault indications in MV networks:
networks with resistor-earthed, directly earthed automatic after time delay, automatic upon
or isolated neutral and compensated system voltage return and manual by a push button
• Remote monitoring of MV substation status • Suitable for connection to power supply wiring
• Remote monitoring of network parameters: load, from LV switchgear
current, power • Suitable for connection with external indicator
• Recordings terminals, wall-mounted on a transformer station
• Monitoring of external IEDs via Modbus protocol • 1 or 2 measuring channels
• Monitoring of substation conditions: • Inrush filtering function
temperature, smokiness, door opening, fuse • Time synchronisation through SCADA, local PC,
tripping etc. Ethernet
• Available 6 binary inputs and 3 output relays
Functions • Memory capacity to store:
• Directional functionality to detect earth faults • - 10000 events
selectively in a standard and emergency mode • - 2000 alarms
of substation operations (optional ICC algorithm • - 6000 system
to detect faults, with „Insensitive to Capacitive • - 30000 measurements
Currents”, a patented solution ) • Variable recording and time-stamping
• Possibility to monitor external IEDs via Modbus • Local and remote operations and maintenance
protocol (substation RTU) performed via a built-in Web server
• Password-protected access to data
Communication • 3 access levels can be defined: Administrator,
• IP standards: Operator, Monitoring.
• IEC870-5-101 and -103 • Cooperation with L500 supervision and control
• DNP3 level 3, serial and TCP/IP system for Easergy range
• Modbus , serial and TCP/IP
• Interfaces:
• GSM/GPRS, radio (FSK/FFSK), PSTN V32,
Ethernet
• RS232/RS485 (external modem)
• Ethernet (extra port)
[ Protection Relays Guide ] Metering and Control Devices / Network Analysers 44
Power Logic ION7550 / ION7650

HIGH PERFORMANCE METER OF NETWORK PARAMETERS - A Class Accuracy
Application • Archives of events and measurements

• Analysis of electrical energy quality and • 5 types of counters
efficiency • In-built fault current detector
• Supervision over reliability of power • Control of 4, 8 or 16 switches at a
supply substation
• Cooperation with ION Enterprise - • Dedicated CTs
power management system • Unified connector for measuring circuit
connections
Measurements
• Accurate and fast measurements of true Other Parameters
RMS values (½ cycle) for 3-phase and • Power and energy metering in
individual phases (voltages, currents, accordance with PN-EN 62053-22 Class
active and reactive power, power factor, 0.2S
frequency and voltage and current • Parameters of electrical energy quality -
asymmetry) recording compliant with PN-EN 61000-
• Setting of mean, minimal and peak 4-30 Class A (confirmed by KEMA and
values (power, current and voltage) PSL laboratories)
• Metering of voltage and current
Technical Parameters harmonics and interharmonics in
• 16 binary inputs accordance with PN-EN 61000-4-7
• 4 output relays • Individual analysis of voltage and current
• 8 analogue outputs - option harmonics (ION7650 for H511 and
ION8800A for H63)
Communication • Assessment of quality of supply voltage
• Ethernet 10/100Base-T/TX/FX, Modbus in accordance with PN-EN 50160
TCP, ION, IEC61850 protocols • Voltage sagging and swelling detection,
• RS232/RS485 with support for Modbus accuracy of ½ cycle (10ms)
RTU master/slave, ION, DNP3 protocol • Capture of ultra-fast transients (up to 20
• Optical port on front panel μs)
• Web Server/e-mail/SNMP/XML • Oscillograph recorder function -
• 1 binary input for internal FPI reset resolution of 1024 samples per a cycle
• 1 output relay for external FPI reset (51kHz)
• 1 output relay for launching an external • GPS time synchronisation
flashing indicator (visibility 50m, a flash • Internal memory of up to 10MB for data
every 1s ) and alarms
• Automatic selectioniser • Built-in LCD display - access to real-
• Automatic changeover switch with time measurements, spectral analysis of
generator start-up function harmonics, vector diagram of voltages
• Paralleling and currents and user-defined screens
[ Protection Relays Guide ] Metering and Control Devices / Network Analysers 45
Power Logic Seria PM800

NETWORK PARAMETER ANALYSER WITH FAULT DETECTION AND OSCILLOGRAPH RECORDING

• Sub-billing, cost allocation, and utility bill • Direct connect voltage inputs. No need for
verification potential transformers (PTs) up to 600 VAC
• Remote monitoring of electrical installations • Intuitive navigation with self-guided, language-
• Mid-range power quality and energy selectable menus
management analysis • Large, anti-glare display with white back-light
• Utility contract optimisation and load provides summary screens with multiple values
preservation • Custom alarming with time-stamping
• Individual harmonic magnitudes and angles and
Features waveform capture (PM850 and PM870)
• Measurement of parameters up to 63rd harmonic • Voltage and current disturbance (sag and swells)
(PM850/870 ) detection and configurable waveform capture
• Binary inputs: 1/8 - option (PM870)
• Binary outputs: 1/4 - option • ANSI C12.20 and IEC 62053-22 Class 0.5S for
• Analogue inputs: 0/4 - option active energy. Accurate energy measurements
• Analogue outputs: 0/4 - option for sub-billing and cost allocation
• Trend curves and short-term forecasting (PM850
Communication i PM870)
• 16 binary inputs • 5 channels to calculate the consumption of
• 4 output relays water, air, gas, electricity and steam in all
• 8 analogue outputs - option models. Each channel can gather impulses from
several inputs.
Communication • Optional remote display unit (distance of up to
• Modbus RTU / RS485 10m from the analyser)
• Optional Ethernet communication port provides
communication via Modbus TCP/IP protocol,
-mail on alarm, web server and Ethernet-to-serial
gateway. Transparent Ready - compliant with
Level 1
[ Protection Relays Guide] SEPAM Range of Protections 46
SEPAM
SEPAM Range of Protections
Series 10: Simple applications for MV lines and distribution transformers

• Series 10 incorporates 3 types of SEPAM relays:
• series 10 N with phase or earth fault overcurrent protection
• series 10 B with overload, 3f short-circuit and earth fault protection
• series 10 A has the same functions as SEPAM series 10 B, with opto-insulated inputs
and extra output relays i
Series 10
Series 20: Overcurrent or voltage protections for typical configurations

• Series 20 incorporates 7 types of SEPAM relays.
• Features:
• 3 types of UMI display types
• 4 current inputs OR 4 voltage inputs
• 10 opto-insulated binary inputs
• 8 output relays
• 1 Modbus communication port
• 1 analogue output (MST module)
Series 20 • 8 RTD temperature measurement inputs (MSA module)
Series 40: Overcurrent or voltage protections for complex configurations

• Series 40 incorporates 13 types of SEPAM protections dedicated for various types of
MV bays.
• Features:
• 4 current inputs
• 3 voltage inputs
• 10 binary inputs
• 8 output relays
• Connection to Ethernet TCP/IP network with Web Server
• Logical equation editor
Series 40
• 1 Modbus communication port
• 16 RTD temperature measurement inputs (MET module)
[ Protection Relays Guide] SEPAM Range of Protections 47
SEPAM
SEPAM Range of Protections
Series 60: Advanced overcurrent and voltage protections

• Series 60 incorporates 8 types of SEPAM protections dedicated for various types of MV
bays.
• Features:
• 4 4 current inputs
Series 60
• 3 voltage inputs
• 16 output relays
• Logical equation editor
• Integrated IEC 61850 and Modbus TCP/IP via RSTP
• Available protocols: Modbus, Modbus TCP/IP, IEC60870-5-103, DNP3 (RS485 or FO)
• 4 communication ports plus 1 local
• 1 analogue output (MSA module)
• External cartridge memory to save settings and configuration
Series 80: Multifunctional overcurrent and voltage protections

• Series 80 incorporates 16 types of SEPAM protections dedicated for various types of MV
bays.
• Features:
• 12 analogue inputs:
- 8 current inputs and 4 voltage inputs Series 80
- 4 current inputs and 8 voltage inputs
• 23 output relays
• 4 communication ports plus 2 local Modbus
• Integrated IEC 61850 and Modbus TCP/IP via RSTP
• Available protocols: Modbus, Modbus TCP/IP, IEC60870-5-103, DNP3 (RS485 or FO)
• External cartridge memory to save settings and configuration
• Logipam - software to program specific logical functions
[ Protection Relays Guide] Product Catalogue (DVD) / MiCOM S1 Studio Software 48
Product Catalogue - DVD Version MiCOM S1 Studio Software Suite
Content Application
• The CD Catalogue covers information • MiCOM S1 Studio is a universal
regarding products made by Schneider protection relay support software which
Electric Energy Poland Sp. z o.o. and enables global access to all data stored
offered in Poland by the Automation & in the relays. The program provides
Information Systems Unit in Swiebodzice. easy access to MiCOM protections of
• A complete offer of MiCOM protection Px20, Px30 and Px40 series, as well as
relays, as well as of time, measuring and to other types of devices.
insulation monitoring relays.
• Possibility to search by product or by a Main Functions
range of operating voltage • One, common program for MiCOM
• Special publications for designers present Px20, Px30 and Px40 relays to
potential uses of the relays, application configure devices and record data
models and possibilities of replacement of • The devices and files can be arranged
legacy products with modern solutions. in accordance with a topology system
- Substation / Voltage Level / Bay. A
Documentation graphical representation of the system
• The CD contains digital documents is displayed in the Explorer’s separate
related to the protections. Those can be window and helps a user to navigate
a catalogue card and/or user manual, the system.
depending on a selected device. • Configuration files upload and
download
• Acquisition of events and disturbances
and analysis of the recorded data
• Real-time visualisation of measurements
• PSL Editor to edit programmable
scheme logics
• Menu text editor
• Bay type configurator
• Configurator of IEC 61850 transmission
in the relays
• Possibility to export configuration files
in CSV format (comma-separated
values) to a spreadsheet or an
application such as CAPE
Page No. 11 9 8 7 6 6 6 7 6 10 10 10 17 18 29 34 35 35
Revision A_2011
Function symbols in accordance with
ANSI / IEEE Std C37.2 - 1996 Standards
MiCOM P111
MiCOM P114
MiCOM P115
MiCOM P116
MiCOM P211
MiCOM P121
MiCOM P122
MiCOM P123
MiCOM P126
MiCOM P127
MiCOM P220
MiCOM P225
MiCOM P521
MiCOM P821
MiCOM P921
MiCOM P922
MiCOM P923
MiCOM P124S
MiCOM P122C
MiCOM P124D
MiCOM P120_1p
MiCOM P125_1p
Main Protection Functions ANSI Code P10 P20
Non-directional phase overcurrent 50/51
Non-directional earth fault 50N/51N
Directional phase overcurrent 67
Directional earth fault 67N
Admittance earth fault 67YN
Phase undercurrent / Loss of load 37
Thermal overload 49/51
Negative phase sequence thermal_I2 / Unbalance load 46
Broken conductor detection 46BC
[ Protection Relays Guide] Product Tables
Circuit breaker failure 50BF

Multi-shot autoreclose (3 – 3 phase trip, 1 - 1 & 3
79
phase trip)
Wattmetric earth fault 32N // 67W
Phase undervoltage 27
Phase overvoltage 59
Negative sequence overvoltage _ U2 47
Positive sequence undervoltage _ U1 27D
Residual overvoltage / Neutral displacement _ Uo 59N
100% stator earth fault (3 harm.)_neutral // terminal 27TN // 59TN
Differential _ current 87
Reverse power_R // Directional power _ F (3 ph
32R // 32F
measure)
Overpower 32O
Low forward power 32L
Overfrequency 81O
Underfrequency 81U
Rate of change of frequency _ df/dt / ROCOF / 81R
Voltage dependent overcurrent 51V
Restricted earth fault (differential) 64N // 87N
Temperature (detectors RTD_R / PTC_P) 26 / 38
Excess long start 48
Locked rotor at start // Satalled rotor 51LR // 50S
Start number 66
Out of step 55
Anti Back Spin ABS *
Check synchronising 25
Trip Circuit Supervision 74TCS
Fault locator FL*
Switch On To Fault 50HS
Measure circuit supervision VTS / CTS
49
12, 34,
Page No. 13,38 24 24 25 32 33 33 33 33
38
Revision A_2011
MiCOM P132
MiCOM P139
MiCOM P433
MiCOM P435
MiCOM P437
MiCOM P439
MiCOM P532
MiCOM P631
MiCOM P632
MiCOM P633
MiCOM P634
MiCOM P130C
MiCOM P430C
MiCOM P530C
MiCOM P630C
Main Protection Functions ANSI Code P30

Admittance earth fault 67YN
Thermal overload 49
Negative phase sequence thermal_I2 / Unbalance load 46
Multi-shot autoreclose (3 – 3 phase trip, 1 - 1 & 3 phase trip) 79 3 3 3 1 1 3

100% stator earth fault (3 harm.)_neutral // terminal 27TN // 59TN
Differential _ current_ G / L / M / T_ phase_PC 87 L L T T T T T
Reverse power_R // Directional power _ F (3 ph measure) 32R // 32F F F F F F F F
Overpower 32O
Overfrequency 81O
Underfrequency 81U
Overfuxing_U/Hz 24
Underimpedance / Impedance / Distance 21
Restricted earth fault (differential) 64 // 87N
Rotor earth fault 64R
Pole slipping_Power swings 78 / 68 P P
Temperature (detectors RTD_R / PTC_P) 26 / 38 R R R R R R R R R
Start number 66
Out of step 55
Anti Back Spin ABS*
Check synchronising 25
Trip Circuit Supervision 74TCS
Fault locator FL*
50
Switch On To Fault 50HS

Measure circuit supervision VTS / CTS
Page No. 14 14 14 15 19 19 19 20 21 21 22 21 27 28 30 30 31 31 31 31 36 37 38 35 35
Revision A_2011
MiCOM
MiCOM
P741/2/3
P443Mho
MiCOM P141
MiCOM P142
MiCOM P143
MiCOM P145
MiCOM P241
MiCOM P242
MiCOM P243
MiCOM P341
MiCOM P342
MiCOM P343
MiCOM P344
MiCOM P345
MiCOM P441
MiCOM P442
MiCOM P444
MiCOM P446
MiCOM P445
MiCOM P541
MiCOM P542
MiCOM P543
MiCOM P544
MiCOM P545
MiCOM P546
MiCOM P547
MiCOM P746
MiCOM P841
MiCOM P941
MiCOM P943
Główna funkcje zabezpieczeniowe ANSI Code P40
One sensitive earth fault admittance stage 67YN
Thermal overload 49
Negative phase sequence thermal_I2 / Unbalance
46
load
Multi-shot autoreclose (3 – 3 phase trip, 1 - 1 &
79 3 3 3 1 1 1 1 3 1
3 phase trip)
100% stator earth fault (3 harm.)_neutral //
27TN // 59TN
terminal
100% stator earth fault (20 Hz generator) 64S
Differential _ current_ G / L / M / T_ phase_PC 87 M G G G L L L L L L L SZ SZ
Reverse power_R // Directional power _ F (3 ph
32R
measure)
Overpower 32O
Overfrequency 81O
Underfrequency 81U
Turbine abnormal frequency 81AB
Voltage vector shift _ dU > VVS *
Loss of field 40
Overfuxing_U/Hz 24
Underimpedance / Impedance / Distance 21
Restricted earth fault (differential) 64 // 87N
Interturn (Split Phase) 50DT
Rotor earth fault 64R
Unintentional energisation at standstill // Dead
50 / 27
machine
Pole slipping_Power swings 78 / 68
Temperature detectors 26 / 38
Start number 66
Out of step 55
Anti Back Spin 25
Check synchronising 74CTS
Trip Circuit Supervision FL*
Fault locator 50HS
51
Switch On To Fault VTS/CTS

Measure circuit supervision
New factory
in STONE!
Manufacturing of
MiCOM Px30, Px40 series.
Schneider Electric Energy Poland Sp. z o.o.

REFA Zakład Automatyki i Systemów Elektroenergetycznych As standards, specyfications and designs change from
58-160 Świebodzice time to time, please ask for confirmation of the information
give in this publication.
ul. Strzegomska 23/27
tel. 74 854 84 10
Publishing: Schneider Electric Energy Poland Sp. z o.o.
fax 74 854 86 98
Design: Schneider Electric Energy Poland Sp. z o.o.
[email protected]
Printing: Schneider Electric Energy Poland Sp. z o.o.
www.schneider-energy.pl

Micom General Catalogue PDF

Uploaded by

Copyright:

Available Formats

Micom General Catalogue PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Micom General Catalogue PDF

Uploaded by

Copyright:

Available Formats

Automation & Information Systems

List of ANSI codes applied in the Guide

Make the most of your energy

• Signalling and remote control

MiCOM C264 C / MiCOM C264 P

Control and signalling circuits Application

SUI (System User Interface)

Application & Functions Advanced Graphic Features

MiCOM P120 / MiCOM P121

MiCOM P122 / MiCOM P123

Application Other Functions

Protections Other Functions

MiCOM P126 / MiCOM P127

Application Other Functions

MiCOM P111 Universal Overcurrent Protection Relay

Overcurrent I> (DT or IDMT) X X X X X Output relays P1 (no) and P2 (no) X X X X X X X

Earth fault admittance Go> X X 2 setting groups X X X X X X X

Earth fault admittance Bo> X X RS485 communication port X X X X X X

CB/contactor control (opto-insulated

CB failure scheme X Recording of last 3 fault trips X X X X X X X

External protection Recording of 25 events with time

MiCOM P141 / MiCOM P142 / MiCOM P143

Application Other Functions

Application Other Functions

MiCOM P241 / MiCOM P242 / MiCOM P243 (Z funkcją zab. różnicowego)

Application Other Functions

MiCOM P342 / MiCOM P343 / MiCOM P344 / MiCOM P345

Application Other Functions

Application Other Functions

MiCOM P433 / MiCOM P435

MiCOMho P443 With sub-cycle technology !!!

Application Other Functions

MiCOMho P446 Interoperates with 2 circuit breakers

Application • Broken conductor detection

Application Other Functions

MiCOM P541 / MiCOM P542

Application Other Functions

MiCOM P543 / MiCOM P544 / MiCOM P545 / MiCOM P546

Application Other Functions

MiCOM P631 / MiCOM P632 / MiCOM P633 / MiCOM P634

Application Other Functions

Application Other Functions

MiCOM P922 / MiCOM P923

Application Other Functions

MiCOM P941 / MiCOM P943

MiCOM P741 (CU) / MiCOM P742 (PU) / MiCOM P743 (PU)

Application Other Functions

Application Other Functions

zone/system • Another independent RS232/RS485 port

MiCOM P132 / MiCOM P139

MiCOM P841 Interoperates with 1 or 2 circuit breakers

Application Other Features

Application Other Features

MiCOM P991 / MiCOM P992 / MiCOM P993

Application Other Features

MiCOM P591 / MiCOM P592 / MiCOM P593

Applications Other Features

Application Other Functions

Application Other Functions