0% found this document useful (0 votes)
1K views5 pages

Assignment - Ch#23 Springs Example Problems

The document provides details and calculations for four examples involving helical coil springs. In the first example, the maximum shear stress in a spring subjected to an axial load of 500 N is calculated to be 534.7 MPa. The second example calculates that a spring can carry an axial load of 412.7 N or 383.4 N depending on whether curvature is considered, with a deflection per turn of 9.96 mm or 9.26 mm respectively. The third example details the design of a spring for a 1000 N scale with an 80 mm deflection, using a 4 mm wire and resulting in a maximum shear stress of 1018.2 MPa. The final example calculates the

Uploaded by

Faris Ahmad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
1K views5 pages

Assignment - Ch#23 Springs Example Problems

The document provides details and calculations for four examples involving helical coil springs. In the first example, the maximum shear stress in a spring subjected to an axial load of 500 N is calculated to be 534.7 MPa. The second example calculates that a spring can carry an axial load of 412.7 N or 383.4 N depending on whether curvature is considered, with a deflection per turn of 9.96 mm or 9.26 mm respectively. The third example details the design of a spring for a 1000 N scale with an 80 mm deflection, using a 4 mm wire and resulting in a maximum shear stress of 1018.2 MPa. The final example calculates the

Uploaded by

Faris Ahmad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Example 23.1.

A compression coil spring made of an alloy steel is having the following


specifications:

Mean diameter of coil = 50 mm ; Wire diameter = 5 mm ; Number of active coils = 20. If this
spring is subjected to an axial load of 500 N ; calculate the maximum shear stress (neglect the
curvature effect) to which the spring material is subjected.

Solution:

Given : D = 50 mm ; d = 5 mm ; n = 20 ; W = 500 N

We know that the spring index,

D 50
C= = =10
d 5

∴ Shear stress factor,

1 1
K s =1+ =1+ =1.05
2C 2 ×10

and maximum shear stress (neglecting the effect of wire curvature),

8W .D 8 ×500 × 50
τ =K s × 3
=1.05 × 3
=534.7 N /mm2=534.7 MPa
πd π×5

Example 23.2. A helical spring is made from a wire of 6 mm diameter and has outside
diameter of 75 mm. If the permissible shear stress is 350 MPa and modulus of rigidity 84
kN/mm2, find the axial load which the spring can carry and the deflection per active turn.

Solution:

Given: d = 6 mm ; Do = 75 mm ; τ = 350 MPa = 350 N/mm2 ; G = 84 kN/mm2 = 84 × 103


N/mm2

We know that mean diameter of the spring,

D=D o−d =75−6=69 mm

∴ Spring index,

D 69
C= = =11.5
d 6

Let, W = Axial Load, and


δ / n = Deflection per active turn.

1. Neglecting the effect of curvature

We know that the shear stress factor,

1 1
K s =1+ =1+ =1.0 43
2C 2 ×1 1.5

and maximum shear stress induced in the wire (τ),

8W .D 8 ×W × 69
350=K s × 3
=1.0 43 × =0.848 W
πd π ×6 3

350
∴W = =412.7 N
0.848

We know that deflection of the spring,

8 W . D3 n
δ=
G . d4

∴ Deflection per active turn,

3
δ 8 W . D3 n 8 × 412.7 ( 69 )
= = =9.96 mm
n G . d4 84 × 103 ×6 4

2. Considering the effect of curvature

We know that Wahl’s stress factor,

4 C−1 0.615
K= + =1.123
4 C−4 C

We also know that the maximum shear stress induced in the wire (τ),

8W .C 8× W ×11.5
350=K × 2
=1. 12 3× =0.913 W
πd π ×6 2

350
∴W = =383 . 4 N
0.913

and deflection of the spring,

8 W . D3 n
δ=
G . d4
∴ Deflection per active turn,

3
δ 8 W . D3 n 8 ×383 . 4 ( 69 )
= = =9. 26 mm
n G . d4 84 × 103 × 64

Example 23.3. Design a spring for a balance to measure 0 to 1000 N over a scale of length
80 mm. The spring is to be enclosed in a casing of 25 mm diameter. The approximate number
of turns is 30. The modulus of rigidity is 85 kN/mm 2. Also calculate the maximum shear
stress induced.

Solution.

Given : W = 1000 N ; δ = 80 mm ; n = 30 ; G = 85 kN/mm2 = 85 × 103 N/mm2

Design of spring

Let D = Mean diameter of the spring coil,

d = Diameter of the spring wire, and

C = Spring index = D/d.

Since the spring is to be enclosed in a casing of 25 mm diameter, therefore the outer diameter
of the spring coil (Do = D + d ) should be less than 25 mm.

We know that deflection of the spring (δ),

8W . C 3 . n 8 ×1000 ×C 3 × 30 240 C 3
80= = =
G. d 85 ×103 × d 85 d

C3 80 ×85
= =28.3
d 240

Let us assume that d = 4 mm. Therefore

C3 = 28.3 d = 28.3 × 4 = 113.2 or C = 4.84

and D = C.d = 4.84 × 4 = 19.36 mm

We know that outer diameter of the spring coil,

Do = D + d = 19.36 + 4 = 23.36 mm

Since the value of Do = 23.36 mm is less than the casing diameter of 25 mm, therefore the
assumed dimension, d = 4 mm is correct.
Maximum shear stress induced

We know that Wahl’s stress factor,

4 C−1 0.615
K= + =1. 322
4 C−4 C

∴ Maximum shear stress induced,

8 W .C 8 ×1000 × 4.84 N
τ =K × 2
=1.322 × 2
=1018.2 =1018.2 MPa
πd π×4 mm 2

Example 23.4. A mechanism used in printing machinery consists of a tension spring


assembled with a preload of 30 N. The wire diameter of spring is 2 mm with a spring index of
6. The spring has 18 active coils. The spring wire is hard-drawn, and oil tempered having the
following material properties: Design shear stress = 680 MPa, Modulus of rigidity = 80
kN/mm2

Determine: 1. the initial torsional shear stress in the wire; 2. spring rate; and 3. the force to
cause the body of the spring to its yield strength.

Solution.

Given : Wi = 30 N; d = 2 mm; C = D/d = 6; n = 18; τ = 680 MPa = 680 N/mm 2 ; G = 80


kN/mm2 = 80 × 103 N/mm2

1. Initial torsional shear stress in the wire

We know that Wahl’s stress factor,

4 C−1 0.615
K= + =1. 2525
4 C−4 C

∴ Initial torsional shear stress in the wire,

8W i . C 8 ×30 ×6 N
τ i =K × 2
=1. 2525 × 2
=143 .5 =143 .5 MPa
πd π×2 mm2

2. Spring Rate

We know that spring rate (or stiffness of the spring),

G.d 80 × 103 × 2
¿ = =5.144 N /mm
8C 3 . n 8 ×6 3 × 18
3. Force to cause the body of the spring to its yield strength

Let W = Force to cause the body of the spring to its yield strength.

We know that design or maximum shear stress (τ),

8W . C 8 ×W × 6
680=K × 2
=1.2525 × =4.78 W
πd π ×22

680
W= =142.25 N
4.78

You might also like