AN6001-G16 Optical Line Terminal Equipment Product Overview Version A

AN6001-G16
Optical Line Terminal Equipment
Product Overview
Version: A
Code: MN000003548
FiberHome Telecommunication Technologies Co., Ltd.
June 2018
Thank you for choosing our products.
We appreciate your business. Your satisfaction is our goal.

We will provide you with comprehensive technical support
and after-sales service. Please contact your local sales
representative, service representative or distributor for any
help needed at the contact information shown below.
Fiberhome Telecommunication Technologies Co., Ltd.
Address: No. 67, Guanggu Chuangye Jie, Wuhan, Hubei, China

Zip code: 430073
Tel: +6 03 7960 0860/0884 (for Malaysia)
+91 98 9985 5448 (for South Asia)
+593 4 501 4529 (for South America)
Fax: +86 27 8717 8521
Website: http://www.fiberhomegroup.com
Legal Notice
are trademarks of FiberHome Telecommunication Technologies Co., Ltd.

(Hereinafter referred to as FiberHome)
All brand names and product names used in this document are used for
identification purposes only and are trademarks or registered trademarks
of their respective holders.
All rights reserved
No part of this document (including the electronic version) may be

reproduced or transmitted in any form or by any means without prior
written permission from FiberHome.
Information in this document is subject to change without notice.
Contents
1 Documentation Guide .....................................................................................1
2 Product Introduction........................................................................................3
2.1 Product Appearance .........................................................................4
2.2 Product Positioning...........................................................................5
2.3 Power Supply Mode..........................................................................5
3 Product Highlights...........................................................................................7
4 Product Application.........................................................................................9
5 Product Specification .................................................................................... 11
5.1 List of Functions and Features ........................................................12
5.2 Major Technical Specifications ........................................................14
5.3 Interface Specifications...................................................................15
6 Product Structure..........................................................................................17
6.1 Logical Architecture ........................................................................18
6.2 Hardware Structure.........................................................................19
6.2.1 Subrack Structure .............................................................19

6.2.2 Functional Modules and Indicators ....................................20
6.2.3 Air Cooling Mode ..............................................................22
6.3 Software Architecture......................................................................22
7 Matching Cables...........................................................................................25
7.1 Cable Overview ..............................................................................26
7.2 Power Cable...................................................................................27
7.2.1 Cabinet Power Cable ........................................................27

7.2.2 Subrack DC Power Cable .................................................28
7.2.3 Subrack AC Power Cable .................................................29
7.3 Protection Earth Ground Cable .......................................................30
7.3.1 Cabinet Protection Earth Ground Cable.............................30

7.3.2 Subrack Protection Earth Ground Cable ............................31
7.3.3 PDP Protection Earth Ground Cable .................................33
7.4 Fiber Jumper ..................................................................................34
7.5 Network Cable ................................................................................35
7.6 Environment Monitoring Unit Connection Cable...............................37
7.7 Serial Port Line ...............................................................................38
7.8 Dry Contact Cable ..........................................................................40
8 Indoor Cabinets ............................................................................................41
8.1 Overview of Cabinets......................................................................42
8.2 Detailed Dimensions of the Cabinets...............................................43
8.2.1 Detailed Parameters of the 19-inch Cabinets .....................44

8.2.2 Detailed Dimensions of the 21-inch Cabinets.....................45
Appendix A Detailed Technical Specifications...............................................46
A.1 Requirements for Operating Environment........................................46
A.2 Card Dimensions ............................................................................46
A.3 GPON Performance........................................................................47
A.4 Reliability........................................................................................47
Appendix B Standards and Protocols ...........................................................48
B.1 Environment Standards ..................................................................48
B.2 EMC Standards ..............................................................................49
B.3 Safety Standards ............................................................................51
B.4 GPON Access Standard .................................................................52
B.5 Standards and Protocols for Services..............................................52
B.6 Standards for Network Protection....................................................55
B.7 Standards for Layer 3 Functions......................................................56
B.8 Other Standards .............................................................................56
Appendix C Panel and Terminals of the PDP ................................................57
Appendix D Abbreviations............................................................................62
1 Documentation Guide
Document Orientation
Product Overview gives a general introduction to the orientation, features, functions,

application, structure and hardware composition of the AN6001-G16 to help users
get an overall knowledge about the product.
Intended Readers
u Marketing personnel
u Commissioning engineers
u Operation and maintenance engineers
Version Information
Version Version Information
A Initial version, corresponding to the equipment version V1R1.
Content
Chapter Content
u Product appearance
Product Introduction u Product positioning
u Power supply mode
Product Highlights Product highlights
Product Application Product application
u List of functions and features

Product Specification u Major technical specifications
u Interface specifications
u Logical architecture
Product Structure u Hardware structure
u Software architecture
Functions, model numbers, structures, connections and
Matching Cables
parameters of wires and cables
Overview, appearance and dimensions of the indoor

Indoor Cabinets
cabinets
Version: A 1
AN6001-G16 Optical Line Terminal Equipment Product Overview
Chapter Content
u Requirements for operating environment
Detailed Technical u Card dimensions
Specifications u GPON performance
u Reliability
Standards and Protocols Standards and protocols that the equipment complies with
Panel and Terminals of the PDP Model numbers, panels and terminals of the PDPs
Related Documentation
Document Applied to
AN6001-G16 Optical Line Terminal Equipment

Network planning phase
Product Overview
AN6001-G16 Optical Line Terminal Equipment Quick Network deployment phase / network
Installation Guide maintenance phase
AN6001-G16 Optical Line Terminal Equipment Network deployment phase / network

UNM2000 Configuration Guide maintenance phase
AN6001-G16 Optical Line Terminal Equipment CLI Network deployment phase / network
Configuration Guide maintenance phase
2 Version: A
2 Product Introduction
Product Appearance
Product Positioning
Power Supply Mode
Version: A 3
2.1 Product Appearance
The AN6001-G16 is a small-sized cassette-shaped optical line access equipment

developed by FiberHome. It is designed with pluggable modularized power cards,
fan unit, core switch service cards and optical modules for easy installation,
deployment and maintenance. It provides GPON access, carrier-class reliability,
sound security mechanism and selective QinQ functions. The UNM2000 is used as
the network management system to enable centralized management, maintenance
and monitoring of the equipment.
The AN6001-G16 supports three power supply schemes: DC-AC, dual-DC, and
dual-AC. The figures below show the appearance of the equipment.
Figure 2-1 AC-DC Power Supply Scheme
Figure 2-2 Dual-DC Power Supply Scheme
Figure 2-3 Dual-AC Power Supply Scheme
4 Version: A
2 Product Introduction
2.2 Product Positioning
The AN6001-G16 mainly serves for telecommunications, radio and television

operators, and provides the last-mile fiber access solution. The small-sized (1U)
cassette-shaped OLT can be deployed in outdoor cabinets and applied to sparsely-
populated villages, towns, and urban villages which have insufficient equipment
rooms and harsh outdoor environment. It caters to the demand of multiple service
scenarios including home access, enterprise access and mobile backhauling.
Generally, the equipment is located at the edge of the access network and
connected to the terminal equipment directly. That is, it lies between the user
equipment and the distribution layer equipment.
2.3 Power Supply Mode
The AN6001-G16 provides three power supply schemes: dual-DC, dual-AC and
DC-AC hybrid schemes. All these schemes support 1+1 redundancy backup.
AC Power Supply
The AN6001-G16 supports 110 V / 220 V active-standby AC power supply featuring

lightning protection, filtering, lightning protection failure alarm and input voltage
detection.
Version: A 5
DC Power Supply
The AN6001-G16 supports -48 V active-standby DC power supply featuring voltage

monitoring, failure alarm reporting and protection switching.
The table below describes the model numbers, appearance and input / output
specifications of the PDPs for the DC power supply scheme of the AN6001-G16.
Item PDP260B PDP296B

3000063-1FA 3000068-1FA
Model number
3000063-2FA 3000068-2FA
Appearance
Range of input
-38 V to -60 V -38 V to -60 V
voltage
Two channels of power (one active Two channels of power (one active
Input channels
and one standby) and one standby)
The maximum current of a single The maximum current of a single

Input current
channel is 96 A. channel is 96 A.
Range of
-38 V to -60 V -38 V to -60 V
output voltage
Output
Six channels of output power Six channels of output power
channels
The maximum current of a single The maximum current of a single
Output current
channel is 32 A. channel is 32 A.
Note:
The AN6001-G16 is equipped with the PDP260B (3000063) by default.

When lightning protection is required, use the PDP296B (3000068)
instead.
6 Version: A
3 Product Highlights
High-density Modularized Integration
u 1U high, designed with modularized core switch service card, fan card and
power card for easy installation and replacement.
u Supports 16 GPON ports, two 10GE uplink ports (SFP+), two GE uplink optical
ports (SFP) and two GE uplink electrical ports to allow access of 1024 ONUs.
Flexible Deployment
Supports mounting in 19-inch / 21-inch cabinets or outdoor cabinets and mounting

on the wall. Suitable for long-haul broadband access applications in villages, towns
and factories. Provides users with access to multiple services such as broadband,
voice and IPTV services; caters to various access demands of telecommunications,
radio and television operators as well as the customer premises network; and saves
the backbone optical fiber resources.
Carrier-class Reliability
u Supports 1+1 redundancy protection for PON ports, uplink ports and power
interfaces. All the slots meet the requirement of fault tolerance.
u Supports Type B PON protection, detection of rogue ONUs and detection of

optical links.
u Supports service switching with the WTR time less than 50 ms.
Abundant Ethernet Functions
u Provides versatile VLAN processing functions, including selective QinQ, VLAN

translation and VLAN aggregation.
u Provides overall QoS functions, including dynamic bandwidth allocation, priority

control, multiple traffic classification mechanisms, and queue scheduling to
meet the QoS demand of different services such as VoIP, IPTV and Internet
access.
u Provides sound ACL functions, including L2, L3 and user-defined ACLs.
Version: A 7
u Supports IGMP Snooping and Proxy, IGMPv3 and MLDv2 source address
filtering, and rate control for multicast packets.
u Supports STP/MSTP, link aggregation, DHCP and port isolation.
u Supports both IPv4 and IPv6 to enable smooth migration to the next-generation
IP network.
Remote Management and Easy Maintenance
u Provides visualized management based on GUI EMS, which covers

configuration, alarm and performance monitoring, data statistics, user
management and so on.
u Supports management based on command lines with downward compatibility.
u Supports remote software upgrade, which simplifies operation and saves man
power.
8 Version: A
4 Product Application
The AN6001-G16 can be deployed on the wall in the hallway of a building or in an

outdoor cabinet to provide the Last Mile fiber access and cater to the broadband
access demand in sparsely-populated areas.
In this scenario, the AN6001-G16, used together with various ONUs, provides
integrated user interfaces and abundant service functions to aggregate, merge, and
forward user data to meet various service access demands of telecommunications,
radio and television operators as well as the customer premises network.
Through uplink ports, the AN6001-G16s can be cascaded to make up an MSTP ring,
so as to provide redundancy protection and enhance network reliability
Version: A 9
10 Version: A
5 Product Specification
List of Functions and Features
Major Technical Specifications
Interface Specifications
Version: A 11
5.1 List of Functions and Features

Classification Function
Access features GPON access
Supports 802.1Q VLAN.
Supports selective QinQ (VLAN Stacking).
Supports independent learning of MAC addresses.
Supports shared learning of MAC addresses.
Clears Layer 2 forwarding table globally.

Layer 2 switching functions
Allows the OLT to forward data based on the MAC
address.
Supports configuring the MAC address aging time for the
OLT and ONU.
Supports Layer 2 port dynamic aggregation and
implements the LACP.
Supports ingress and egress mirroring.

Port mirroring
Supports flow mirroring.
Supports the IEEE 802.3ad protocol.

Port aggregation
Supports static or LACP dynamic port aggregation.
Supports isolation of GPON ports.

Port isolation
Supports isolation of uplink ports.
Supports 4-level HQoS functions.

QoS functions
Supports IPv4 / IPv6 QoS.
Supports IGMP Proxy / Snooping and MLD Proxy.
Supports the IGMP V1 / V2 / V3 and MLD V1 / V2

protocols.
Supports multicast VLAN.

Multicast functions
Supports multicast copy broadcast.
Supports multicast information statistics.
Supports multicast user management.
Supports multicast program management.
Supports VoIP voice service.
Supports H.248 and SIP protocols.
Supports PPPoE configuration.

Voice functions
Supports DHCP configuration.
Supports query of NGN statistics information.
Supports query of NGN resource status.
12 Version: A
Supports voice intercommunication inside the PON.
Supports VLAN Layer 3 interface.
Supports ARP proxy.
Supports DHCP Relay, DHCP Snooping or DHCP Server.

Layer 3 functions
Isolates illegal DHCP Server.
Supports dynamic routing based on OSPF.
Supports static routing.
Supports relay agent Option18 / Option37 function of

Line identification function DHCPv6.
Supports DHCP option82 and PPPoE+.
Supports cascading over Ethernet networks.
Supports bidirectional forwarding detection (BFD).

Network features Supports the STP protocol (IEEE802.1D), RSTP protocol
(IEEE 802.1w) and MSTP protocol (IEEE 802.1s).
Supports the ERPS function.
Supports remote operation and user management.
Supports operation authority classification.
Supports exception handling for the equipment.
Supports version and data management.
Supports saving and querying the performance statistics

Operation and maintenance and historical data.
Supports remote upgrade of the software.
Supports automatic rollback during software upgrade.
Synchronizes equipment configuration with EMS

configuration.
Supports the License function.
Clock in the system
1588v2 clock
Clocks
Adaptive clock recovery
Synchronous Ethernet clock
Supports 1+1 protection for PON ports.
System redundancy Supports 1+1 protection for uplink ports.
Supports 1+1 protection for DC or AC power interfaces.
Each uplink port supports up to 120 ACL rules.

Security features Authenticates ONU terminals and reports illegal ONU
registration events.
Version: A 13
Supports limit on maximum number of MAC addresses
learned to prevent attacks by users' MAC addresses.
Supports filtering MAC addresses.
Supports filtering packets and binding ports based on the

source MAC address, destination MAC address, Ethernet
type, VLAN, CoS, source IP address, destination IP
address, IP port and protocol type.
Prevents DoS attacks.
5.2 Major Technical Specifications

Item Description
Dimensions of the subrack without mounting ears (H

44.4 mm × 443 mm × 220 mm (1U)
× W × D)
Dimensions of the subrack with mounting ears for 19-

44.4 mm × 480 mm × 225 mm
inch cabinet (H × W × D)
Dimensions of the subrack with mounting ears for 21-

44.4 mm × 530 mm × 233 mm
inch cabinet (H × W × D)
Overall weight 4.5 kg
DC voltage range: -38.4 VDC to -57.6 VDC

Power
AC voltage range: 90 VAC to 290 VAC
Maximum power consumption: 90 W

Overall power consumptionNote 1
Static power consumption: 57 W
System switching capability 44 G

Slot bandwidth 20 G
CONSOLE/ESC: RS232 local debugging serial port / RS485
environment monitoring port
Management and monitoring interface 1PPS/TOD: clock interface

ETH: out-of-band network management interface
DC1-7: dry contact interface
PON port 16 GPON ports
10GE1/10GE2: 10GE uplink port (SFP+)
Uplink interface GE3/GE4: GE uplink optical port (SFP)
GE5/GE6: GE uplink electrical port
Long-term operating temperature: 0°C to 45°C

Working temperatureNote 2
Short-term operating temperature: -10°C to 55°C
14 Version: A
Item Description
Long-term operating humidity: 5％ to 85％ (no condensation)

Working humidity
Short-term operating humidity: 5％ to 90% (no condensation)
Note 1: The overall power consumption is measured under the following conditions:
u Maximum power consumption: all the ports are 100% loaded.
u Static power consumption: all the ports are unloaded, and the optical ports are not plugged with optical modules.
Note 2: The working temperature is measured within an altitude of 1800 m. The ambient temperature of the
equipment will reduce by 1°C for each altitude rise of 220 m.
5.3 Interface Specifications
The pluggable optical modules applied to the AN6001-G16 have two encapsulation
formats: SFP and SFP+.
There are two types of module interfaces: LC and SC, as shown in the figure below.
The table below describes the mappings between the modules and the equipment
interfaces.
Equipment
Module Type Application Code Module Code
Interface
GPON optical CLASS C+ 2.5/1.25G-20km-GPON OLT-SFP (CLASS C+)

1 to 16
module CLASS C++ 2.5/1.25G-20km-GPON OLT-SFP (CLASS C++)
10GBASE-LR 10G-10km-TDM-SFP+ (10GBASE-LR)

10GE optical
10GE1/10GE2 10GBASE-ER 10G-40km-TDM-SFP+ (10GBASE-ER)
module
10GBASE-ZR 10G-80km-TDM-SFP+ (10GBASE-ZR)
1000BASE-LX 1.25G-10km-TDM-SFP (1000BASE-LX)

GE optical
GE3/GE4 1000BASE-EX 1.25G-40km-TDM-SFP (1000BASE-EX)
module
1000BASE-ZX1 1.25G-80km-TDM-SFP (1000BASE-ZX1)
Version: A 15
The AN6001-G16 also provides four network ports for RJ-45 connectors. The table
below describes the mapping between the ports and the cables connected.
Equipment
Interface Description Cable Connected
Interface
u RS232 local debugging serial port u Serial Port Line
(CONSOLE) u Environment
CONSOLE/ESC
u RS485 environment monitoring Monitoring Unit
interface (ESC) Connection Cable
1PPS/TOD External clock device interface Network Cable
Out-of-band network management
ETH Network Cable
interface
DC1-7 Dry contact interface Dry Contact Cable
16 Version: A
6 Product Structure
Logical Architecture
Hardware Structure
Software Architecture
Version: A 17
6.1 Logical Architecture
The figure below shows the logical architecture of the AN6001-G16.
The AN6001-G16 implements the switching based on IP packet core. The core
switch service card communicates via the backplane buses (combination of the data
bus and management bus) interconnected at high speed to exchange service data
or management information.
The table below describes the interfaces of the AN6001-G16.
Classification Interface Description
10GE1/10GE2 10GE uplink port, using SFP+ encapsulation
Uplink interface GE3/GE4 GE uplink optical port, using SFP encapsulation
GE5/GE6 GE uplink electrical port
RS232 local debugging serial port and RS485 environment

CONSOLE/ESC
monitoring port
Management and
1PPS/TOD Clock interface
monitoring interface
ETH Out-of-band network management interface
DC1-7 Seven dry contact ports
GPON port 1 to 16 16 GPON ports
AC power input interface; 110 V / 220 V; supporting 1+1

Power interface PWRA
protection switching
18 Version: A
6 Product Structure
Classification Interface Description
DC power input interface; -48 V; supporting 1+1 protection

PWRD
switching
6.2 Hardware Structure
This section introduces the subrack structure, functional modules, indicator LEDs
and air cooling mode for the AN6001-G16.
6.2.1 Subrack Structure
The figure below shows the components of the AN6001-G16 subrack using the AC-
DC hybrid power supply scheme as an example.
No. Name Function

① Mounting ear Secures the subrack in the cabinet.
ESD protection earth ground
② Connects to the ESD protection device.
fastener
Facilitates routing and arranging of fibers and
③ Fiber passage unit
cables.
④ Fan card Facilitates air cooling for the equipment.
Provides access to GPON services; provides GE /

⑤ Core switch service card 10GE uplink ports, and interfaces for
management, monitoring and debugging.
Inducts 110 V / 220 V AC power supply. Here it

⑥ AC power card can be replaced by a DC power card to provide 1
+1 DC power protection.
Version: A 19
No. Name Function

Inducts -48 V DC power supply. Here it can be
⑦ DC power card replaced by an AC power card to provide 1+1 AC
power protection.
⑧ Subrack earth ground point Connects with the subrack earth ground cable.
6.2.2 Functional Modules and Indicators
Module Allocation
Three module allocation schemes are available to the AN6001-G16, corresponding

to the power supply modes used.
Figure 6-1 AC-DC Power Supply Scheme
Figure 6-2 Dual-DC Power Supply Scheme
Figure 6-3 Dual-AC Power Supply Scheme
20 Version: A
6 Product Structure
Virtual Card
The AN6001-G16 implements the upper-layer management in the virtual card mode.
The core switch service card (HSOA) integrates three virtual cards: GPOP, HSCP
and HU2P. The virtual cards are integrated with the subrack and cannot be plugged
/ unplugged or replaced.
The figure below illustrates the allocation of virtual slots in the AN6001-G16 subrack.
Indicator LEDs
The table below describes the indicator LEDs of the AN6001-G16.
Identifier Meaning Color Status Description
ON The card is working normally.
Blinking
The card is being initialized.
ACTNote 1 Working indicator LED Green slowly
The card is not powered on or is not

OFF
working normally.
ON The card has alarms.

ALM Alarm indicator LED Red
OFF The card has no alarms.
The port is connected to an ONU at the

ON far end, and the ONU has been
authorized.
LINK: link status
GPON port Green
indicatorNote 2
The port is not connected to an ONU at
OFF the far end, or the far-end ONU is not
authorized.
Version: A 21
Identifier Meaning Color Status Description
The port is connected with the upper-

ON
layer device.
Uplink The port is transmitting data to or

LINK: link status
optical Green Blinking receiving data from the upper-layer
indicatorNote 3
interface device.
The port is not connected with the
OFF
upper-layer device.
The port is connected to the upper-layer

ON device without data transmission
LINK: link status
Green between them.
Uplink indicator
electrical The port is not connected with the
OFF
interface upper-layer device.
ACT: data status Blinking The port has data flow.

Yellow
indicator OFF The port has no data flow.
Note 1: The ACT indicators of the power card and fan card do not have the Blinking Slowly status.
Note 2: The left and right LINK indicators correspond to the upper and lower GPON ports respectively.
Note 3: The left and right LINK indicators correspond to the upper and lower uplink optical ports respectively.
6.2.3 Air Cooling Mode
The AN6001-G16 is designed with forced air cooling. The fan card is located at the
right side of the subrack (front view). The cool air is drawn from the left side to the
right side of the subrack to take away the heat, as illustrated in the figure below.
6.3 Software Architecture

Software Architecture of the Core Switch Module
The figure below illustrates the core switch software architecture of the AN6001-
G16.
22 Version: A
6 Product Structure
u Support plane: Serves the entire system, available for all the layers and
modules in the system; provides universal operating system and supports
hardware transplantation; provides complete software tool set, session
management, and IPC encapsulation.
u Management plane: Manages equipment based on Telnet, WEB, SSH, SNMP,

RMON and so on; intervenes in the operation of the control plane when
necessary.
u Control plane: Controls the operation of all network protocols; supports flexible
configuration of functional modules to cater to various application scenarios.
u Data plane: Manages the configuration data, status data, alarm time data and
operation data of functional modules and protocol modules in the system
collectively.
Software Architecture of the Service Module
The figure below illustrates the service software architecture of the AN6001-G16.
Version: A 23
u Operating system layer: Works based on the Linux operating system.
u System support layer: Provides system support and fault diagnosis functions
such as the operating system abstract layer (OSAL), command lines, logs and
hot patches.
u Driver layer: Provides the PON MAC and SW chip driver.
u PON driver isolation layer: Defines the universal PON_API interface and
shields the difference in underlying hardware schemes so that the upper-layer
software can make use of the OLT underlying hardware functions.
u Infrastructure layer: Provides the infrastructure module to set up the service

card architecture.
u Service logic layer: Defines the service model and the service modules based
on it.
24 Version: A
7 Matching Cables
Cable Overview
Power Cable
Protection Earth Ground Cable
Fiber Jumper
Network Cable
Environment Monitoring Unit Connection Cable
Serial Port Line
Dry Contact Cable
Version: A 25
7.1 Cable Overview

Cable Model Applied to
-48 V power cable: 3696234 (16 mm2) / 3696231

(25 mm2)
PDP260B (3000063)
0 V power cable: 3696235 (16 mm2) / 3696232 (25
mm2)
Cabinet Power Cable
-48 V power cable: 408000076 (16 mm2) /
408000021 (25 mm2)
PDP296B (3000068)
0 V power cable: 408000075 (16 mm2) / 408000020
(25 mm2)
Subrack DC Power
408000062 The PWRD card of the equipment
Cable
Subrack AC Power
WX00219 The PWRA card of the equipment
Cable
Connecting the earth ground point
Cabinet Protection Earth on the top of the cabinet and the
408000041 (16 mm2), 408000019 (25 mm2)
Ground Cable ground busbar in the equipment
room
Subrack Protection Earth
3696084 The equipment subrack
Ground Cable
PDP Protection Earth 3696239 PDP260B (3000063)

Ground Cable 408000018 PDP296B (3000068)
LC/PC-type optical fiber jumper: OFC-LC/PC- The 10GE1 / 10GE2 port or GE3 /
LC/PC-S-20 GE4 port of the HSOA card
Fiber Jumper
SC/PC-type optical fiber jumper: OFC-SC/PC-
Ports 1 to 16 of the HSOA card
SC/PC-S-20
The GE5 / GE6 port, 1PPS/TOD
Network Cable 3695095 interface or ETH interface of the
HSOA card
Environment Monitoring The CONSOLE/ESC interface of
409000159
Unit Connection Cable the HSOA card
The CONSOLE/ESC interface of
Serial Port Line 3695341
the HSOA card
The DC1-7 interface of the HSOA
Dry Contact Cable 3695452
card
26 Version: A
7 Matching Cables
7.2 Power Cable
The power cables supply electric energy to loads so that the loads can work
normally.
7.2.1 Cabinet Power Cable
Function
The cabinet power cables, including the -48 V power cable and the 0 V power cable,
are used to induct the power source for the equipment room to the PDP inside the
cabinet.
Model
The AN6001-G16 can use the PDP260B (3000063) or PDP296B (3000068). The
cabinet power cables vary with the PDP used. Table 7-1 describes the mappings
between the cabinet power cables and the PDPs. Please refer to this table and
select appropriate cabinet power cables for the PDP.
Table 7-1 Model Numbers of Cabinet Power Cables
PDP Model Cable Type Cable Model Cable Color

3696234 (16 mm2)
-48 V power cable Blue
3696231 (25 mm2)
PDP260B (3000063)
3696235 (16 mm2)
0 V power cable Black
3696232 (25 mm2)
408000076 (16 mm2)

-48 V power cable Blue
408000021 (25 mm2)
PDP296B (3000068)
408000075 (16 mm2)
0 V power cable Black
408000020 (25 mm2)
Structure
Cable Model Description Illustration

3696231, 3696232, M10 uninsulated ring
3696234 and 3696235 terminal + bare wire
408000020, 408000021, M6 uninsulated ring
408000075 and 408000076 terminal + bare wire
Version: A 27
Connection
PDP Model Cable Type Internal Connector External Connector

-48V1 connector (active)
-48 V power cable External -48 V
-48V2 connector
(blue) connector
PDP260B (standby)
(3000063) GND1 connector (active)
0 V power cable External 0 V
GND2 connector
(black) connector
(standby)
-48V_A connector
-48 V power cable (active) External -48 V
(blue) -48V_B connector connector
PDP296B
(standby)
(3000068)
0V_A connector (active)
0 V power cable External 0 V
0V_B connector
(black) connector
(standby)
Technical Specifications
Item Specification
Double-sheathed, heat-resistant (withstanding a

Cable type
temperature up to 105℃), and single-core soft cable
u 16 mm2 power cable: 80 A

Maximum rated current
u 25 mm2 power cable: 100 A
7.2.2 Subrack DC Power Cable
Function
The subrack DC power cable connects the PDP and the equipment's DC power
card (PWRD) to induct a set of redundant branch power rails from the PDP to the
subrack.
Model
The model number of the subrack DC power cable for the AN6001-G16 is
408000062.
28 Version: A
7 Matching Cables
Structure
The subrack DC power cable has a two-conductor power plug on one end and two
cord end terminals on the other end, as illustrated in the figure below.
(1) Two-conductor power plug (2) -48 V cord end terminal (3) 0 V cord end terminal
Connection
Connection Description
No. Cable Connector
PDP260B (3000063) PDP296B (3000068)
Two-conductor Connected to the power input interface of the DC power card

(1)
power plug (PWRD).
Connected to the -48V_A_1 to

Cord end terminal Connected to the -48 V
(2) -48V_A_3 / -48V_B_1 to -48V_B_
(-48 V, blue) connector on the PDP.
3 connectors on the PDP.
Connected to the 0V_A_1 to 0V_
Cord end terminal Connected to the 0 V
(3) A_3 / 0V_B_1 to 0V_B_3
(0 V, black) connector on the PDP.
connectors on the PDP.
Item Specification
Cable type Sheathed two-conductor cable
Color Blue (-48 V), black (0 V)
Maximum current 16 A
Cross-sectional area of the conductor 2 × 1.5 mm2
7.2.3 Subrack AC Power Cable
Function
The subrack AC power cable is used to connect the external AC power supply and
the AC power card (PWRA) of the equipment, inducting the external AC power into
the subrack.
Version: A 29
Model
The model number of the AN6001-G16 subrack AC power cable is WX00219.
Structure
As shown in the figure below, the subrack AC power cable has a three-conductor
power plug on one end and a three-conductor power jack on the other end.
Connection
Cable Cable Connector Connection Description
Tree-conductor
Connected to the external power supply unit.
Subrack AC power plug
cable Tree-conductor Connected to the power input interface of the AC
jack power card (PWRA).
7.3 Protection Earth Ground Cable
The protection earth ground cables (including the cabinet protection earth ground
cable and the subrack protection earth ground cable) protect the equipment from
lightning and interference.
7.3.1 Cabinet Protection Earth Ground Cable
Function
The cabinet protection earth ground cable is used to connect the earth ground point
on the top of the cabinet and the ground busbar in the equipment room.
30 Version: A
7 Matching Cables
Model
The AN6001-G16 can use the cabinet protection earth ground cables with the
model numbers 408000041 (16 mm2) and 408000019 (25 mm2).
Structure
As shown in the figure below, the yellow- / green cable has an M6 uninsulated ring
terminal on one end for connection with the cabinet. You need to make a grounding
terminal on the other end of the cable for connection with the busbar.
Connection
Cable Connector Description
M6 uninsulated ring
Connected to the earth ground point on the top of the cabinet.
terminal
Bare wire terminal Prepared according to the earth ground point on the busbar.
Item Specification
Cable type Single core soft cable
Color Yellow- / green
u 16 mm2 protection earth ground cable: 80 A

Maximum rated current
u 25 mm2 protection earth ground cable: 100 A
7.3.2 Subrack Protection Earth Ground Cable
Function
The subrack protection earth ground cable is used to connect the subrack and the
protection earth ground terminal of the cabinet to provide ground protection for the
subrack.
Version: A 31
Model
The model number of the subrack protection earth ground cable used by the
AN6001-G16 is 3696084.
Structure
The figure below shows the subrack protection earth ground cable. Both ends of the
cable are M6 pre-insulation terminals, and between them is a yellow- / green cable.
Connection
Cable Connector Connection Description
M6 pre-insulation ring terminal Connects to the cabinet earth ground point.
M6 pre-insulation ring terminal Connects to the subrack earth ground point.
Item Specification
Single-sheathed heat-resistant (withstanding a

Cable type
temperature up to 90℃) single-core soft cable
Color Yellow- / green
Maximum current 32 A
Cross-sectional area of the conductor 4 mm2
32 Version: A
7 Matching Cables
7.3.3 PDP Protection Earth Ground Cable
Function
The PDP protection earth ground cable is used to connect the protection ground of
the PDP and the earth ground point on the top of the cabinet. Before delivery, this
cable has been connected to the PE terminal of the PDP.
Model
The AN6001-G16 can be equipped with PDP260B (3000063) or PDP296B

(3000068). The protection earth ground cables used on the two PDPs are different.
See Table 7-2 for the mappings between the PDPs and their protection earth
ground cables.
Table 7-2 Protection Earth Ground Cables for the PDPs
PDP Model Cable Model

PDP260B (3000063) 3696239
PDP296B (3000068) 408000018
Structure
Cable Model Description Appearance
Comprises an M10
uninsulated ring terminal at
the PDP side and an M6
3696239 uninsulated ring terminal at
the cabinet side, with a
yellow- / green cable between
them.
Comprises an M6 uninsulated
copper cord end terminal at
the PDP side and an M6 pre-
408000018
insulation ring terminal at the
cabinet side, with a yellow- /
green cable between them.
Version: A 33
Connection
PDP Model Cable Model Cable Connector Description
Connected to the PE terminal

M10 uninsulated ring terminal
of the PDP.
PDP260B
3696239 Connected to the earth
(3000063)
M6 uninsulated ring terminal ground point on the top of the
cabinet.
M6 uninsulated copper cord Connected to the PE terminal
end terminal of the PDP.
PDP296B
408000018 Connected to the earth
(3000068) M6 pre-insulation ring
ground point on the top of the
terminal
cabinet.
Note:
The PDP protection earth ground cable has been connected to the inner
PE connector of the PDP before delivery; therefore, you only need to
connect the cable to the earth ground point on the top of cabinet on site.
Maximum Cross-sectional Area of

Cable Model Cable Type Color
Current Conductor
3696239 Single core Yellow- / 63 A 10 mm2
408000018 soft cable green 40 A 6 mm2
7.4 Fiber Jumper

Function
Serving as the transmission carrier of optical signals, the fiber jumper is applied to
the short-distance transmission of optical signals. It connects an optical interface of
the equipment's card and the ODF.
Model
Classification Model
LC/PC-type optical fiber jumper OFC-LC/PC-LC/PC-S-20
SC/PC-type optical fiber jumper OFC-SC/PC-SC/PC-S-20
34 Version: A
7 Matching Cables
Structure
Classification Connector
LC/PC-type fiber connector
SC/PC-type fiber connector
Connection
Cable Connector Card Interface Connected Connection on the ODF Side
Connected to the remote ONU to
SC/PC connector Ports 1 to 16 of the HSOA card
provide the GPON downlink channel.
The 10GE1 / 10GE2 port of the

Fiber jumper
HSOA card Connected to the IP network to provide
LC/PC connector
The GE3 / GE4 interface of the the GE and 10 GE optical channels.
HSOA card
Reference for Choosing Fiber Jumpers
Parameter Basis for Choice

Length On-site investigation
Single-mode / multi-mode Type of the optical module
Fiber connector type Type of the optical module
7.5 Network Cable

Function
The network cable is used to connect the local equipment to the uplink equipment,
out-of-band network management system or time synchronization device.
Model
The model number of the network cable (including straight-through network cable
and cross-over network cable) is 3695095.
Version: A 35
Structure
Both ends of the network cable are equipped with the RJ-45 connectors (also
known as crystal heads), as shown in the figure below.
Table 7-3 lists the pin definitions for the straight-through network cable.
Table 7-3 Pin Definitions for the Straight-through Network Cable
Pin of the Local End Wire Color Pin of the Opposite End
1 White- / orange 1
2 Orange 2
3 White- / green 3
4 Blue 4
5 White- / blue 5
6 Green 6
7 White- / brown 7
8 Brown 8
Table 7-4 lists the pin definitions for the cross-over network cable.
Table 7-4 Pin Definitions for the Cross-over Network Cable
1 White- / orange 3
2 Orange 6
3 White- / green 1
4 Blue 4
5 White- / blue 5
36 Version: A
7 Matching Cables
Table 7-4 Pin Definitions for the Cross-over Network Cable (Continued)
6 Green 2
7 White- / brown 7
8 Brown 8
Connection
Cable Card Interface Connected Connection at the Opposite End
The GE5 / GE6 port, ETH Connected to the uplink equipment, out-
Network cable interface or 1PPS/TOD interface of-band network management system
of the HSOA card or time synchronization device.
Item Specification
Cable type CAT-5 twisted pair
Connector type RJ-45

Number of conductors 8
Conductor diameter AWG24
Breakdown voltage 2000 V
7.6 Environment Monitoring Unit Connection

Cable
Function
The environment monitoring unit connection cable is used to connect the

CONSOLE/ESC interface of the equipment to the external environment monitoring
device.
Model
The model number of the environment monitoring unit connection cable is

409000159.
Version: A 37
Structure
The table below defines the pins of the environment monitoring unit connection
cable.
1 White- / orange 7
2 Orange 8
7 White- / brown 5
8 Brown 6
7.7 Serial Port Line

Function
The serial port line is used for debugging or local maintenance. It connects the local
debugging serial port of the HSOA card and the serial port of the network
management computer.
Model
The model number of the serial port line is 3695341.
38 Version: A
7 Matching Cables
Structure
Table 7-5 lists the terminal definitions for the serial port line.
Table 7-5 Terminal Definitions for the Serial Port Line
Connected Signal RJ-45 Connector Pin DE-9S Connector Pin
Signal transmitted by the

3 2
equipment
GND 4/5 5
Signal received by the
6 3
equipment
Connection
Connected to the CONSOLE/ESC interface of the

RJ-45 connector
HSOA card.
Serial port line
Connected to the serial port of the network
DE-9S connector
management computer.
Item Specification
Cable outside diameter 5.2±0.3 mm

Maximum DC resistance of conductor 93.8Ω/km
Characteristic impedance 100±15Ω
Version: A 39
7.8 Dry Contact Cable

Function
The dry contact cable is used to connect the dry contact interface on a card to an
external dry contact device to enable monitoring of infrared detection, smoke, mains
supply, humidity, temperature, fans, shake, door access control, etc.
Model
The model number of the dry contact cable is 3695452.
Structure
Connection
Connected to the DC1-7 interface of

RJ-45 connector
Dry contact cable the HSOA card.
Bare wire end Connected to the dry contact device.
Item Specification
Cable type CAT-5 twisted pair
Connector type RJ-45

Conductor diameter AWG24
40 Version: A
8 Indoor Cabinets
Overview of Cabinets
Detailed Dimensions of the Cabinets
Version: A 41
8.1 Overview of Cabinets

Table 8-1 Overview of Cabinet Models
Cabinet 404000068 to 404000337 to

4102596 to 4102599 4102589 to 4102592
Model 404000071 404000340
19-inch 600 mm-deep 21-inch 300 mm-deep 21-inch 300 mm-deep 21-inch 340 mm-deep
Descrip-
cabinet with anti-dust cabinet without anti- cabinet with anti-dust cabinet without anti-
tion Note 1 Note 1
screen dust screen screen dust screen
Appear-
ance
Note 1:
u Among the SC/PC optical fiber connectors, the 55 mm long and 39 mm long ones are
most commonly used. The 55 mm ones are called long connectors, and the 39 mm ones
are called short connectors. When the equipment is mounted in a 300 mm-deep cabinet, it
Remarks is advisable to use the 39 mm optical fiber connectors (short connectors).
u Among the LC/PC optical fiber connectors, the 48 mm long and 31 mm long ones are
most commonly used. The 48 mm ones are called long connectors, and the 31 mm ones
are called short connectors. When the equipment is mounted in a 300 mm-deep cabinet, it
is advisable to use the 31 mm optical fiber connectors (short connectors).
42 Version: A
8 Indoor Cabinets
Table 8-2 Dimensions and Weight of the Cabinets
Cabinet Type Cabinet Model Dimensions (H × W × D) (mm) Weight (kg)
4102596 1600 × 600 × 600 94

19-inch 600 mm-deep
4102597 2000 × 600 × 600 109
cabinet with anti-dust
4102598 2200 × 600 × 600 117
screen
4102599 2600 × 600 × 600 134
4102589 1600 × 600 × 300 56
21-inch 300 mm-deep
4102590 2000 × 600 × 300 61
cabinet without anti-dust
4102591 2200 × 600 × 300 66
screen
4102592 2600 × 600 × 300 76
404000068 1600 × 600 × 300 58
21-inch 300 mm-deep
404000069 2000 × 600 × 300 69
cabinet with anti-dust
404000070 2200 × 600 × 300 74
screen
404000071 2600 × 600 × 300 85
404000337 1600 × 600 × 340 57.5
21-inch 340 mm-deep
404000338 2000 × 600 × 340 62.5
cabinet without anti-dust
404000339 2200 × 600 × 340 67.5
screen
404000340 2600 × 600 × 340 77.5
8.2 Detailed Dimensions of the Cabinets
The following introduces the detailed dimensions of the 19-inch and 21-inch
cabinets.
Version: A 43
8.2.1 Detailed Parameters of the 19-inch Cabinets
Figure 8-1 Detailed Dimensions of the 19-inch Cabinet
Table 8-3 Detailed Parameters of the 19-inch Cabinet
Item Specification
Distance between holes on the mounting flange 1 U = 44.45 mm

Angle opening width 450 mm
Fixing centres 465 mm
44 Version: A
8 Indoor Cabinets
8.2.2 Detailed Dimensions of the 21-inch Cabinets
Figure 8-2 Detailed Dimensions of the 21-inch Cabinet
Table 8-4 Detailed Dimensions of the 21-inch Cabinet
Item Specification
Distance between holes on the mounting flange 1 SU = 25 mm

Angle opening width 500 mm
Fixing centres 515 mm
Version: A 45
Appendix A Detailed Technical
Specifications
A.1 Requirements for Operating Environment

Item Requirement
Bearing capacity of the floor in the

＞ 600 kg/m2
equipment room
Grounding resistance ＜ 10Ω

Atmospheric pressure 70 kPa to 106 kPa
Altitude -60 m to 4000 m
Temperature change rate ≤ 0.5℃/min
No corrosive and solvent gas, and no dust; no strong
Ambient air quality
electromagnetic fields nearby.
Solar radiation ≤ 700 W/m2

Thermal radiation ≤ 600 W/m2
Concentration of mechanical active Suspended dust: ≤ 0.4 mg/m3
substances Deposited dust: ≤ 15 mg/(m3·h)
Gravel: ≤ 300 mg/m3
SO2 ≤ 0.30 mg/m3
H2S ≤ 0.10 mg/m3
NOx ≤ 0.50 mg/m3
Concentration of chemical NH3 ≤ 1.00 mg/m3

substances Cl2 ≤ 0.10 mg/m3
HCl ≤ 0.10 mg/m3
HF ≤ 0.01 mg/m3
O3 ≤ 0.05mg/m3
Noise standard ≤ 63 dBA (measured at a temperature of 23±2℃)
A.2 Card Dimensions
The AN6001-G16 contains the HSOA, PWRA/PWRD and FAN cards. The table
below lists the dimensions of the cards.
46 Version: A
Appendix A Detailed Technical Specifications
Card Type Dimensions (H × W × D)
Core switch service card (HSOA) 40.8 mm × 277 mm × 207.5 mm

AC power card (PWRA) 39.6 mm × 64 mm × 205.5 mm
DC power card (PWRD) 39.6 mm × 64 mm × 205.5 mm
Fan card (FAN) 44.2 mm × 30.8 mm × 209.5 mm
A.3 GPON Performance

Item Description
Provides 16 GPON ports.
Supports access of 1024 ONUs.
Uplink rate: 1.24416 Gbps; downlink rate: 2.48832 Gbps
Supports Type B protection switching.

GPON performance Supports downlink GEM frame encryption.
Maximum transmission distance: 60 km

Maximum differential fiber distance: 40 km
TCONT:1000
Throughput: 88 Gbps
A.4 Reliability
Equipment Model Basic Reliability Task Reliability
AN6001-G16 30 000 h 50 000 h

Note 1: The mean time to repair (MTTR) for the entire system is 0.5 hour.
Version: A 47
Appendix B Standards and
Protocols
B.1 Environment Standards

Standard Number Title
Environmental Engineering (EE)
Environmental conditions and environmental tests for
telecommunications equipment
Part 1-1: Classification of environmental conditions: Storage
ETSI EN 300 019-1-1
Class 1.1: Weather-protected, partly temperature-controlled
storage locations
Class 1.2: Weather-protected, not temperature-controlled storage
locations
ETSI EN 300 019-1-2 Part 1-2: Classification of environmental conditions:
Transportation
Class 2.1: Very careful transportation
Class 2.2: Careful transportation

ETSI EN 300 019-1-3 Part 1-3: Classification of environmental conditions: Stationary
use at weather-protected locations
Class 3.1: Temperature-controlled locations
Class 3.2: Partly temperature-controlled location

ETSI EN 300 753 telecommunications equipment
October 1997: Acoustic noise emitted by telecommunications
equipment
IEC 60068-2 Basic Environmental Testing Procedures
Environmental conditions appearing in nature - Earthquake

IEC 60721-2-6
vibration
48 Version: A
Appendix B Standards and Protocols

Amendment 1 - Modular order for the development of mechanical
IEC 60721-3-1 structures for electronic equipment practices - Part 1: Generic
standard
Classification of environmental conditions - Part 3: Classification
IEC 60721-3-3 of groups of environmental parameters and their severities -
Section 3: Stationary use at weather-protected locations
Equipment Engineering (EE)

ETSI EN 300 753
Acoustic noise emitted by telecommunications equipment
Network Equipment-Building System (NEBS) Requirements:

NEBS GR-63-CORE
Physical Protection
Restriction of the use of certain hazardous substance in electrical

ROHS
and electronic equipment.
Information technology equipment - Safety - Part 22: Equipment

IEC 60950-22-2005
to be installed outdoors
Mechanical structures for electronic equipment - Tests for IEC
IEC 61587-1-2007 60917 and IEC 60297 - Part 1: Climatic, mechanical tests and
safety aspects for cabinets, racks, subracks and chassis

IEC 61587-2-2000 60917 and IEC 60297 - Part 2: Seismic tests for cabinets and
racks
IEC 61587-3-2006 60917 and IEC 60297 - Part 3: Electromagnetic shielding
performance tests for cabinets, racks and subracks
UL Standard for Safety Test for Flammability of Plastic Materials

UL 94-1996
for Parts in Devices and Appliances Fifth Edition
B.2 EMC Standards

Information technology equipment – Radio disturbance
CISPR 22
characteristics – Limits and methods of measurement
Information technology equipment – Immunity characteristics –
CISPR 24
Limits and methods of measurement
Electromagnetic compatibility and Radio spectrum Matters
EN 300 386 (ERM); Telecommunication network equipment; Electromagnetic
Compatibility (EMC) requirements
Information technology equipment – Radio disturbance

EN 55022
characteristics - Limits and methods of measurement
Version: A 49

Information technology equipment – Immunity characteristics –
EN 55024
Electromagnetic compatibility (EMC) – Part 4 – 2: Electrostatic
EN 61000-4-2
discharge immunity test
Electromagnetic compatibility (EMC) – Part 4 – 3: Testing and

EN 61000-4-3 measurement techniques-Radiated, radio-frequency,
electromagnetic field immunity test

EN 61000-4-4 measurement techniques-Electrical fast transient/burst immunity
test
Electromagnetic compatibility (EMC) – Part4 – 5: Testing and
EN 61000-4-5
measurement techniques-Surge immunity test

EN 61000-4-6 measurement techniques-Immunity to conducted disturbances,
induced by radio-frequency fields
Power supply interface at the input telecommunications

ETSI EN 300132-2
equipment; Part 2: Operated by direct current (DC)
Electromagnetic compatibility and Radio spectrum Matters

ETSI EN 300386 V 1.4.1 (ERM); Telecommunication network equipment; Electromagnetic
Compatibility (EMC) requirements
Electromagnetic compatibility - Limits - Limits for harmonic current

IEC 61000-3-2
emissions (equipment input current k 16 A per phase)
Electromagnetic compatibility- Limits - Limitation of voltage

changes, voltage fluctuation and flicker in public low-voltage
IEC 61000-3-3
supply systems, for equipment with rated current ≤16A per phase
and not subject to conditional connection
Electromagnetic compatibility (EMC) – Part 4 – 2:Testing and

IEC 61000-4-2
measurement techniques-Electrostatic discharge immunity test

IEC 61000-4-3 measurement techniques-Radiated, radio-frequency,
electromagnetic field immunity test
Electromagnetic compatibility (EMC) - Part 4 - 4: Testing and

IEC 61000-4-4 measurement techniques-Electrical fast transient/burst immunity
test
IEC 61000-4-5
measurement techniques-Surge immunity test

IEC 61000-4-6 measurement techniques-Immunity to conducted disturbances,
induced by radio-frequency fields
50 Version: A

Electromagnetic compatibility - Testing and measurement
IEC 61000-4-8
techniques - Power frequency magnetic field immunity test
Electromagnetic compatibility - Testing and measurement

IEC 61000-4-11 techniques - Voltage dips, short interruption and voltage variations
immunity tests
Resistibility of telecommunication equipment installed in a

ITU-T K.20
telecommunications centre to overvoltages and overcurrents
ITU-T K.43 Immunity requirements for telecommunication equipment
EMC requirements for telecommunication equipment - Product

ITU-T K.48
family Recommendation
Electromagnetic compatibility requirement for telecommunication

EN 300 386
network equipment
Information technology equipment - Radio disturbance

CISPR 22 (EN55022)
characteristics - Limits and methods of measurement
Information technology equipment - Immunity characteristics -
CISPR 24 (EN55024)
B.3 Safety Standards

Safety of laser products - Part 1: Equipment classification and
EN 60825-1
requirements
Safety of laser products - Part 2: Safety of optical fibre

EN 60825-2
communication
Information technology equipment -Safety - Part 1: General
EN 60950-1
Requirements
Safety of Information Technology Equipment. Including Electrical

IEC 60950-1
Business Equipment
Safety of laser products - Part 1: Equipment classification and

IEC 60825-1
requirements
Safety of laser products - Part 2: Safety of optical fibre

IEC 60825-2
communication
Safety of Information technology equipment including Electrical
IEC 60950-2001
Business Equipment
Information Technology Equipment - Safety - Part 1: General

UL 60950-1:2003
Requirements
CAN/CSA-C22.2 No Safety of Information Technology Equipment Including Electrical

60950-1 Business Equipment
Version: A 51

Safety of Information Technology Equipment Including Electrical
UL 60950-1
Business Equipment (3rd edition)
IEC Publication 479-1 Guide on the effects of current passing through the human body
IS 8437 {1993} Guide on the effects of current passing through the human body
Safety of information technology equipment including electrical

IS 13252 {1993}
business equipment
B.4 GPON Access Standard

Gigabit-capable passive optical networks (GPON): General
ITU-T G.984.1
characteristics
Gigabit-capable Passive Optical Networks (GPON): Physical
ITU-T G.984.2
Media Dependent (PMD) layer specification
Gigabit-capable Passive Optical Networks (G-PON): Transmission

ITU-T G.984.3
convergence layer specification
ITU-T G.Imp984.3 Implementers' Guide for ITU-T Rec. G.984.3 (02/2004)
Gigabit-capable passive optical networks (G-PON): ONT

ITU-T G.984.4
management and control interface specification
ITU-T G.Imp.984.4 Implementor's Guide for ITU-T Rec. G.984.4
ITU-T G.984.5 Enhancement band for gigabit capable optical access networks
Gigabit-capable passive optical networks (GPON): Reach

ITU-T G.984.6
extension
ITU-T G.988 ONU management and control interface (OMCI) specification
B.5 Standards and Protocols for Services

Protocols for NGN Voice Service
ITU-T G.711 Pulse code modulation (PCM) of voice frequencies
ITU-T G.711.1 Wideband embedded extension for G.711 pulse code modulation
Dual rate speech coder for multimedia communications

ITU-T G.723.1
transmitting at 5.3 and 6.3 kbit/s
Coding of speech at 8 kbit/s using conjugate-structure algebraic-

ITU-T G.729
code-excited linear prediction (CS-ACELP)
52 Version: A

G.729 based Embedded Variable bit-rate coder: An 8-32 kbit/s
ITU-T G.729.1
scalable wideband coder bitstream interoperable with G.729
Implementers' Guide for G.729 Annexes B, F, G, I and C+ (Coding

ITU-T G.Imp 729
of speech at 8 kbit/s using CS-ACELP)
RFC3261 SIP: Session Initiation Protocol

RFC3261 SIP: Session Initiation Protocol
RFC2327 SDP: Session Description Protocol
Reliability of Provisional Responses in the Session Initiation

RFC3262
Protocol (SIP)
RFC4028 Session Timers in the Session Initiation Protocol (SIP)
RFC3525 Gateway Control Protocol Version 1
RFC3015 Megaco Protocol Version 1.0
ITU-TH.248.1 Gateway control protocol: Version 3
Real-time Transport Protocol (RTP) Payload for Comfort Noise

RFC3389
(CN)
Procedures for document facsimile transmission in the general

ITU-TT.30
switched telephone network
Procedures for real-time Group 3 facsimile communication over IP

ITU-TT.38
networks
RFC3550 A Transport Protocol for Real-Time Applications
RFC3611 RTP Control Protocol Extended Reports (RTCPXR)
ITU-TQ.23 Technical features of push-button telephone sets
ITU-TQ.24 Multifrequency push-button signal reception
ITU-TE.180 Technical characteristics of tones for the telephone service
RIP Payload for DTMF Digits, Telephony Tones and Telephony

RFC2833
Signals
RFC2198 RTP Payload for Redundant Audio Data
ITU-TG.168 Digital network echo cancellers
Protocols for Multicast Service

IETF RFC 1112 Host Extensions for IP Multicasting
IETF RFC 2236 Internet Group Management Protocol, Version 2
IETF RFC 3376 Internet Group Management Protocol, Version 3
IETF RFC 2710 Multicast Listener Discovery (MLD) for IPv6
IETF RFC 3810 Multicast Listener Discovery Version 2 (MLDv2) for IPv6
Version: A 53
Time Standards
IEEE Standard for a Precision Clock Synchronization Protocol for
IEEE 1588-2008
Networked Measurement and Control Systems
Network Time Protocol (Version 3) Specification, Implementation

IETF RFC 1305
and Analysis
Simple Network Time Protocol (SNTP) Version 4 for IPv4, IPv6

IETF RFC 2030
and OSI
Time-of-day distribution and maintenance updates and
G.984.3-Amendment 2
clarifications
Ethernet Protocols
IEEE Standard for Local and Metropolitan Area Networks:
IEEE 802-2001
Overview and Architecture
IEEE Standard for Local and Metropolitan Area Networks - Virtual
IEEE 802.1ad
Bridged Local Area Networks - Amendment 4: Provider Bridges
IEEE Standard for Local and Metropolitan Area Networks Virtual

IEEE 802.1ag-2007 Bridged Local Area Networks Amendment 5: Connectivity Fault
Management
Local and metropolitan area networks - Common specifications -

IEEE 802.1w-2001 Part 3: Media access control (MAC) bridges; Amendment 2: Rapid
reconfiguration
IEEE Standard for Local and Metropolitan Area Networks Port-

IEEE 802.1x-2004
Based Network Access Control
IEEE Standard for Local and metropolitan area networks: Media
IEEE 802.1D-2004
Access Control (MAC) Bridges
IEEE Standard for Local and Metropolitan Area Networks - Virtual

IEEE 802.1Q-2005
Bridged Local Area Networks - Amendment 4: Provider Bridges
IEEE Standard for Information technology- Telecommunications

and information exchange between systems - Local and
metropolitan area networks - Specific requirements Part 3: Carrier
IEEE 802.3ah Sense Multiple Access with Collision Detection (CSMA/CD)
Access Method and Physical Layer Specifications Amendment:
Media Access Control Parameters, Physical Layers, and
Management Parameters for Subscriber Access Networks
IEEE Standards for Local and metropolitan area networks - Virtual

IEEE 802.1s-2002 Bridged Local Area Networks - Amendment 3: Multiple Spanning
Trees
54 Version: A

An architectural framework for support of Quality of Service in
ITU-T Y.1291
packet networks
Requirements for OAM functions in Ethernet-based networks and

ITU-T Y.1730
Ethernet services
TR-101 Migration to Ethernet-Based DSL Aggregation
ITU-T Y.1731 OAM functions and mechanisms for Ethernet-based networks

Connectivity Fault Management, IEEE Standard for Local and
IEEE 802.1ag Metropolitan Area Networks Virtual Bridged Local Area Networks
Amendment 5
B.6 Standards for Network Protection

Reference Standard for Ethernet Link Aggregation

IEEE Standard for Local and metropolitan area networks - Link
IEEE 802.1AX-2008
Aggregation
Reference Standard for MSTP

IEEE Std 802.1d 1998 Edition, Spanning Tree Protocol
IEEE Std 802.1w-2001 Rapid Spanning Tree Protocol
IEEE Std 802.1s-2002 Multiple Spanning Tree Protocol
Reference Standard for ERPS

Ethernet ring protection switching. The Edition 1 supports the
ITU-T G.8032 V1
single ring protection, single instance, and revertive mode.
Ethernet ring protection switching. In Edition 2, multi-ring

protection, multi-instance, and non-revertive mode are developed,
ITU-T G.8032 V2 the FDB (Forwarding Database) flush mechanism is optimized,
and forced switch, manual switch and the Clear command are
supported.
Version: A 55
B.7 Standards for Layer 3 Functions

Reference Standard for ARP
An Ethernet Address Resolution Protocol or Converting Network
IETF RFC 826 Protocol Addresses to 48.bit Ethernet Address for Transmission
on Ethernet Hardware
Reference Standard for ARP Proxy

IETF RFC1027 Using ARP to Implement Transparent Subnet Gateways
Reference Standard for DHCP Relay

RFC 2131 Dynamic Host Configuration Protocol
Reference Standard for DHCP Proxy

dsl2006[1].127.00 Proposals of DHCP relay improvements
B.8 Other Standards

IETF RFC 2284 PPP Extensible Authentication Protocol (EAP)
Specification for Diagnostic Monitoring Interface for Optical

SFF-8472
Transceivers (Rev 10.3 Dec.1, 2007)
Optical fibre outside plant maintenance support, monitoring and

ITU-T Rec L.40
testing system
ITU-T Rec L.53 Optical fibre maintenance criteria for access networks
IETF RFC 2362 Protocol Independent Multicast-Sparse Mode
IETF RFC 1723 RIP Version 2 Carrying Additional Information
IETF RFC 2453 RIP Version 2
56 Version: A
Appendix C Panel and Terminals of
the PDP
The following introduces the terminal board and power connectors of the PDP260B
(3000063).
Terminal Board
(1) Branch power rail output (2) External power -48 V (3) External power 0 V input
connector 1 input connector connector
(4) Protection earth ground (5) Branch power rail output (6) Automatic circuit breaker
cable connector connector 2
(7) Branch power rail 0 V (8) Branch power rail 0 V
output connector 1 output connector 2
Power Connectors
Connector Type No. Connector Description
-48 V external power input connectors.

(2) -48V1, -48V2
The two connectors back up each other.
External power input (2 × 0 V external power input connectors. The

(3) GND1, GND2
1 channels) two connectors back up each other.
Connected to the earth ground point on

(4) PE
the top of the cabinet.
Version: A 57
Power automatic circuit breakers. The

outer connectors act as the -48 V branch
(1) -48V1 to -48V3 (on P1)
power output connectors, corresponding
to P1.
Power automatic circuit breakers. The
Branch power rail output outer connectors act as the -48 V branch
(5) -48V1 to -48V3 (on P2)
(2 × 3 channels) power output connectors, corresponding
to P2.
0 V branch power output connector,
(7) 0V (on P1)
corresponding to P1.
0 V branch power output connector,

(8) 0V (on P2 )
corresponding to P2.
The following introduces the front panel, terminal board, power / alarm connectors,
jumper pins and lightning protection module of the PDP296B (3000068).
Front Panel
The PDP296B (3000068) has six air automatic circuit breakers on its front panel to
control the power supply outputs. Among which:
u The ACBs SW1-1 to SW1-3 control the branch power rails -48V_A_1 to
-48V_A_3 respectively .
u The ACBs SW2-1 to SW2-3 control the branch power rails -48V_B_1 to
-48V_B_3 respectively .
58 Version: A
Appendix C Panel and Terminals of the PDP
Terminal Board
(1) Branch power rail -48V (2) Alarm connector for the (3) Cabinet top indicator LED
output connector A head of row cabinet alarm connector
(4) External power -48V input (5) External power 0V input (6) Protection earth ground
connector connector cable connector
(7) Branch power rail -48V (8) Branch power rail 0V (9) Lightning protection module
output connector B output connector B
(10) Jumper pin for selecting (11) Branch power rail 0V (12) Subrack alarm
the working status indicator output connector A convergence connector
LED of the PDP
(13) Buzzer
Power Connectors
-48 V external power input connectors. The

(4) -48V_A, -48V_B -48V_A and -48V_B connectors back up each
other.
External power input (2 ×
0 V external power input connectors. The 0V_
1 channels) (5) 0V_A, 0V_B
A and 0V_B connectors back up each other.
Connected to the earth ground point on the

(6) PE
top of the cabinet.
Automatic circuit breakers (ACBs). The outer

-48V_A_1 to -48V_A_
(1) connectors are -48 V branch power rail output
3
connectors corresponding to -48V_A.
Branch power rail output Automatic circuit breakers (ACBs). The outer
-48V_B_1 to -48V_B_
(2 × 3 channels) (7) connectors are -48 V branch power rail output
3
connectors corresponding to -48V_B.
0V_A_1 to 0V_A_3 0 V branch power rail output connectors,

(11)
(XS1) corresponding to 0V_A.
Version: A 59
0V_B_1 to 0V_B_3 0 V branch power rail output connectors,

(8)
(XS2) corresponding to 0V_B.
Alarm Connector
Subrack alarm RJ-45 sockets receiving the alarm information

(12) AlmIn1 to AlmIn3
convergence connector from the equipment inside the cabinet
Alarm output connector XP6 is a three-conductor D-type socket,

for the head of row (2) XP1 which can output the alarm information to the
cabinet head of row cabinet.
XP7 is a six-conductor D-type socket, which
Alarm output connector
(3) XS4 can output the alarm indicator triggering signal
for indicator LEDs
to the cabinet-top indicator LEDs.
Jumper Pin
JP1 is the jumper pin for selecting the operating status indicator LED of the PDP. It
is located as indicated by (10) in the figure, and can be set in either of the following
two ways:
u Short pin1 and pin2 of JP1, and the green indicator LED on the top of the
cabinet will indicate the working status of the PDP.
u Short pin2 and pin3 of JP1, and the green indicator LED on the top of the
cabinet will be controlled by the CALL (order wire call) signal.
Note:
Pin2 and pin3 of JP1 have been shorted by default before delivery of the
PDP.
Lightning Protection Module
The lightning protection module is plugged into the base of XS3, as indicated by (9)
in the figure.
60 Version: A
Appendix C Panel and Terminals of the PDP
The lightning protection module, using the standard DB-25 plug, can withstand the
surge of 2 kV (1.2/50 us - 8/20 us combination wave) in the common mode and the
surge of 1 kV (1.2/50 us - 8/20 us combination wave) in the differential mode, so as
to guarantee the normal operation of the equipment.
Version: A 61
Appendix D Abbreviations
Authentication, Authorization and

AAA
Accounting
ACL Access Control List

ARP Address Resolution Protocol
BFD Bidirectional Forwarding Detection
BLV Basics Level Vectoring
BRAS Broadband Remote Access Server

BSS Base Station Subsystem
BSC Base Station Controller

Buf Buffer
CoS Class of Service
DHCP Dynamic Host Configuration Protocol
DoS Denial of Service

FMC Fixed Mobile Convergence
FTTB Fiber To The Building
FTTC Fiber To The Curb

FTTH Fiber To The Home
FTTO Fiber To The Office
FTP File Transfer Protocol
GEM GPON Encapsulation Mode
Gigabit-capable Passive Optical

GPON
Network
HASH HASH
HQoS Hierarchical Quality of Service
Internet Group Management

IGMP
Protocol
IMS IP Multimedia Subsystem
IP Internet Protocol
IPTV Internet Protocol Television
IPv4 Internet Protocol version 4
IPv6 Internet Protocol version 6
LACP Link Aggregation Control Protocol
MAC Medium Access Control

MDU Multi-Dwelling Unit
62 Version: A
Appendix D Abbreviations
MGC Media Gateway Controller
MGCP Media Gateway Control Protocol
MIB Management Information Base
MLD Multicast Listener Discover

MOS Mean Opinion Score
MSAN MultiService Access Node

MSC Media Server Controller
MSTP Multiple Spanning Tree Protocol
MTBF Mean Time Between Failure

MTTR Mean Time To Repair
NGN Next Generation Network

Operation, Administration And
OAM
Maintenance
ODN Optical Distribution Network
ONU Optical Network Unit
OSAL Operating System Abstraction Layer
OSPF Open Shortest Path First
OSS Operations Support System
OLT Optical Line Termination
PDP Power Distribution Panel

PON Passive Optical Network
POTS Plain Old Telephone Service

ppm parts per million
PPPoE Point to Point Protocol over Ethernet

PSTN Public Switched Telephone Network
PTN Public Telecommunications Network

QinQ 802.1Q-in-802.1Q
QoS Quality of Service
Remote Authentication Dial In User

RADIUS
Service
RMON Remote Network Monitoring
RSTP Rapid Spanning Tree Protocol
RTP Real-time Transport Protocol
SBU Single Business Unit
Small Form-factor Pluggable

SFP
transceiver
SFU Single Family Unit
Version: A 63
Symmetric High bit rate Digital

SHDSL
Subscriber Line
SIP Session Initiation Protocol
SLV System Level Vectoring
SNI Service Node Interface

Simple Network Management
SNMP
Protocol
SSH Secure Shell
STB Set Top Box
STP Straight-Through Processing
TCP Transmission Control Protocol

VLAN Virtual Local Area Network
VoIP Voice over Internet Protocol
64 Version: A
Product Documentation Customer Satisfaction Survey
Thank you for reading and using the product documentation provided by FiberHome. Please take a moment to
complete this survey. Your answers will help us to improve the documentation and better suit your needs. Your
responses will be confidential and given serious consideration. The personal information requested is used for
no other purposes than to respond to your feedback.
Name
Phone Number
Email Address
Company
To help us better understand your needs, please focus your answers on a single documentation or a complete
documentation set.
Documentation Name
Code and Version
Usage of the product documentation:

1. How often do you use the documentation?
□ Frequently □ Rarely □ Never □ Other (please specify)
2. When do you use the documentation?
□ in starting up a project □ in installing the product □ in daily maintenance □ in trouble
shooting □ Other (please specify)
3. What is the percentage of the operations on the product for which you can get instruction from the
documentation?
□ 100% □ 80% □ 50% □ 0% □ Other (please specify)
4. Are you satisfied with the promptness with which we update the documentation?
□ Satisfied □ Unsatisfied (your advice)
5. Which documentation form do you prefer?
□ Print edition □ Electronic edition □ Other (please specify)
Quality of the product documentation:
1. Is the information organized and presented clearly?
□ Very □ Somewhat □ Not at all (your advice)
2. How do you like the language style of the documentation?
□ Good □ Normal □ Poor (please specify)
3. Are any contents in the documentation inconsistent with the product?
4. Is the information complete in the documentation?
□ Yes
□ No (Please specify)
5. Are the product working principles and the relevant technologies covered in the documentation sufficient for
you to get known and use the product?
□ Yes
□ No (Please specify)
6. Can you successfully implement a task following the operation steps given in the documentation?
□ Yes (Please give an example)
□ No (Please specify the reason)
7. Which parts of the documentation are you satisfied with?
8. Which parts of the documentation are you unsatisfied with?Why?
9. What is your opinion on the Figures in the documentation?
□ Beautiful □ Unbeautiful (your advice)
□ Practical □ Unpractical (your advice)
10. What is your opinion on the layout of the documentation?

□ Beautiful □ Unbeautiful (your advice)
11. Thinking of the documentations you have ever read offered by other companies, how would you compare
our documentation to them?
Product documentations from other companies:
Satisfied (please specify)
Unsatisfied (please specify)
12. Additional comments about our documentation or suggestions on how we can improve:
Thank you for your assistance. Please fax or send the completed survey to us at the contact information
included in the documentation. If you have any questions or concerns about this survey please email at
[email protected]

AN6001-G16 Optical Line Terminal Equipment Product Overview Version A

Uploaded by

Copyright:

Available Formats

AN6001-G16 Optical Line Terminal Equipment Product Overview Version A

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

AN6001-G16 Optical Line Terminal Equipment Product Overview Version A

Uploaded by

Copyright:

Available Formats

AN6001-G16

Optical Line Terminal Equipment

FiberHome Telecommunication Technologies Co., Ltd.

We appreciate your business. Your satisfaction is our goal.

Fiberhome Telecommunication Technologies Co., Ltd.

Address: No. 67, Guanggu Chuangye Jie, Wuhan, Hubei, China

are trademarks of FiberHome Telecommunication Technologies Co., Ltd.

All rights reserved

No part of this document (including the electronic version) may be

1 Documentation Guide .....................................................................................1

2.1 Product Appearance .........................................................................4

2.2 Product Positioning...........................................................................5

2.3 Power Supply Mode..........................................................................5

5 Product Specification .................................................................................... 11

5.1 List of Functions and Features ........................................................12

5.2 Major Technical Specifications ........................................................14

5.3 Interface Specifications...................................................................15

6.1 Logical Architecture ........................................................................18

6.2 Hardware Structure.........................................................................19

6.2.1 Subrack Structure .............................................................19

6.3 Software Architecture......................................................................22

7.1 Cable Overview ..............................................................................26

7.2 Power Cable...................................................................................27

7.2.1 Cabinet Power Cable ........................................................27

7.3 Protection Earth Ground Cable .......................................................30

7.3.1 Cabinet Protection Earth Ground Cable.............................30

7.4 Fiber Jumper ..................................................................................34

7.5 Network Cable ................................................................................35

7.6 Environment Monitoring Unit Connection Cable...............................37

7.7 Serial Port Line ...............................................................................38

7.8 Dry Contact Cable ..........................................................................40

8 Indoor Cabinets ............................................................................................41

8.1 Overview of Cabinets......................................................................42

8.2 Detailed Dimensions of the Cabinets...............................................43

8.2.1 Detailed Parameters of the 19-inch Cabinets .....................44

Appendix A Detailed Technical Specifications...............................................46

A.1 Requirements for Operating Environment........................................46

A.2 Card Dimensions ............................................................................46

A.3 GPON Performance........................................................................47

Appendix B Standards and Protocols ...........................................................48

B.1 Environment Standards ..................................................................48

B.2 EMC Standards ..............................................................................49

B.3 Safety Standards ............................................................................51

B.4 GPON Access Standard .................................................................52

B.5 Standards and Protocols for Services..............................................52

B.6 Standards for Network Protection....................................................55

B.7 Standards for Layer 3 Functions......................................................56

B.8 Other Standards .............................................................................56

Appendix C Panel and Terminals of the PDP ................................................57

Product Overview gives a general introduction to the orientation, features, functions,

u Operation and maintenance engineers

Product Highlights Product highlights

Product Application Product application

u List of functions and features

Overview, appearance and dimensions of the indoor

AN6001-G16 Optical Line Terminal Equipment

AN6001-G16 Optical Line Terminal Equipment Network deployment phase / network

Power Supply Mode