Scribd Logo
Upload

Welcome to Scribd!

  • 71 views

    Surface Vehicle Standard: 400 Commonwealth Drive, Warrendale, PA 15096-0001

    Uploaded by

    anupthatta

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Surface Vehicle Standard: 400 Commonwealth Drive, Warrendale, PA 15096-0001

    Uploaded by

    anupthatta
    71 views3 pages

    Original Title

    SAEJ96v001.pdf

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    71 views3 pages

    Surface Vehicle Standard: 400 Commonwealth Drive, Warrendale, PA 15096-0001

    Uploaded by

    anupthatta

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    SURFACE J96

    REAF.
    MAR86
    VEHICLE
    400 Commonwealth Drive, Warrendale, PA 15096-0001
    STANDARD Issued 1973-05
    Reaffirmed 1986-03

    Superseding J96
    Submitted for recognition as an American National Standard

    FLASHING WARNING LAMP FOR INDUSTRIAL EQUIPMENT

    Foreword—This Document has not changed other than to put it into the new SAE Technical Standards Board
    Format.

    1. Scope—This SAE Standard covers the general requirements and the test requirements for a flashing warning
    lamp for industrial wheeled equipment.

    2. References

    2.1 Applicable Publications—The following publications form a part of this specification to the extent specified
    herein. Unless otherwise specified, the latest issue of SAE publications shall apply.

    2.1.1 SAE PUBLICATIONS—Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001.

    SAE J567—Lamp Bulb Retention System


    SAE J575—Tests for Motor Vehicle Lighting Devices and Components
    SAE J578—Color Specification for Electric Signal Lighting Devices
    SAE J588—Turn Signal Lamps for Use on Motor Vehicles Less Than 2032 mm in Overall Width

    3. Definitions

    3.1 Industrial Wheeled Equipment—That class of tractors and associated equipment used in operations such as
    landscaping, construction services, loading, digging, grounds keeping, and highway maintenance.

    3.2 Flashing Warning Lamp—A lighted device to indicate both forward and rearward the presence of industrial
    equipment which normally travel at rates of speed below that of other traffic.

    4. General Requirements

    4.1 The lamp shall comply in both the forward and rearward direction with the candela requirements of a turn
    signal lamp, SAE J588, Table 1. In addition, the lamp shall project at least 4 cd on both sides at 90 deg to the
    lamp axis.

    4.2 The color of the light from the warning lamp shall be amber in accordance with SAE J578.

    4.3 The lamp shall be flashed at least 60 fpm (flashes per minute) but not more than 120 fpm when it is operating.

    SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely
    voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.”

    SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.

    QUESTIONS REGARDING THIS DOCUMENT: (724) 772-8512 FAX: (724) 776-0243


    TO PLACE A DOCUMENT ORDER; (724) 776-4970 FAX: (724) 776-0790
    SAE WEB ADDRESS http://www.sae.org

    Copyright 1986 Society of Automotive Engineers, Inc.


    All rights reserved. Printed in U.S.A.
    SAE J96 Reaffirmed MAR86

    4.4 The effective projected illuminated area measured on a plane at right angles to the axis of the lamp shall not be
    less than 12 in2 (77.5 mm2).

    4.5 The bulb sockets shall comply with SAE J567.

    5. Test Requirements—The flashing warning lamp shall be tested according to the following sections of SAE
    J575:

    Section B - Samples for Test


    Section C - Lamp Bulbs
    Section D - Laboratory Facilities
    Section E - Vibration Test
    Section F - Moisture Test
    Section G - Dust Test
    Section H - Corrosion Test
    Section J - Photometric Test - All beam candela measurements shall be made with the filament of the
    signal lamp at least 10 ft (3 m) from the photometer screen. The lamp axis is the horizontal line
    through the filament parallel to what would be the longitudinal axis of the vehicle if the lamp were
    mounted in its normal position on the vehicle.
    Section L - Warpage Test on Devices with Plastic Lenses

    PREPARED BY THE SAE OFF-ROAD MACHINERY TECHNICAL COMMITTEE SC5—


    ELECTRICAL EQUIPMENT

    -2-
    SAE J96 Reaffirmed MAR86

    Rationale—Not applicable.

    Relationship of SAE Standard to ISO Standard—Not applicable.

    Application—This SAE Standard covers the general requirements and the test requirements for a flashing
    warning lamp for industrial wheeled equipment.

    Reference Section

    SAE J567—Lamp Bulb Retention System

    SAE J575—Tests for Motor Vehicle Lighting Devices and Components

    SAE J588—Turn Signal Lamps for Use on Motor Vehicles Less Than 2032 mm in Overall Width

    SAE J578—Color Specification for Electric Signal Lighting Devices

    Developed by the SAE Off-Road Machinery Technical Committee SC5—Electrical Equipment

    Sponsored by the SAE Off-Road Machinery Technical Committee

    You might also like