±
    
SLLS410I − JANUARY 2000 − REVISED JANUARY 2004

D RS-232 Bus-Pin ESD Protection Exceeds D, DB, DW, OR PW PACKAGE

±15 kV Using Human-Body Model (HBM) (TOP VIEW)

D Meets or Exceeds the Requirements of

C1+ 1 16 VCC
TIA/EIA-232-F and ITU v.28 Standards
V+ 2 15 GND
D Operates With 3-V to 5.5-V VCC Supply C1− 3 14 DOUT1
D Operates Up To 250 kbit/s C2+ 4 13 RIN1
D Two Drivers and Two Receivers C2− 5 12 ROUT1
D Low Supply Current . . . 300 µA Typical V− 6 11 DIN1
DOUT2 7 10 DIN2
D External Capacitors . . . 4 × 0.1 µF 8 9
RIN2 ROUT2
D Accepts 5-V Logic Input With 3.3-V Supply
D Alternative High-Speed Pin-Compatible
Device (1 Mbit/s)
− SNx5C3232
D Applications
− Battery-Powered Systems, PDAs,
Notebooks, Laptops, Palmtop PCs, and
Hand-Held Equipment

description/ordering information

ORDERING INFORMATION
ORDERABLE TOP-SIDE
TA PACKAGE†
PART NUMBER MARKING
Tube of 40 MAX3232CD
SOIC (D) MAX3232C
Reel of 2500 MAX3232CDR
Tube of 40 MAX3232CDW
SOIC (DW) MAX3232C
Reel of 2000 MAX3232CDWR
−0°C to 70°C
Tube of 80 MAX3232CDB
SSOP (DB) MA3232C
Reel of 2000 MAX3232CDBR
Tube of 90 MAX3232CPW
TSSOP (PW) MA3232C
Reel of 2000 MAX3232CPWR
Tube of 40 MAX3232ID
SOIC (D) MAX3232I
Reel of 2500 MAX3232IDR
Tube of 40 MAX3232IDW
SOIC (DW) MAX3232I
Reel of 2000 MAX3232IDWR
−40°C to 85°C
Tube of 80 MAX3232IDB
SSOP (DB) MB3232I
Reel of 2000 MAX3232IDBR
Tube of 90 MAX3232IPW
TSSOP (PW) MB3232I
Reel of 2000 MAX3232IPWR
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are
available at www.ti.com/sc/package.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

    !"# $ %&'# "$  (&)*%"# +"#' Copyright  2004, Texas Instruments Incorporated
+&%#$ %! # $('%%"#$ (' #,' #'!$  '-"$ $#&!'#$
$#"+"+ .""#/ +&%# (%'$$0 +'$ # '%'$$"*/ %*&+'
#'$#0  "** (""!'#'$

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1



 


    
 ±
    
SLLS410I − JANUARY 2000 − REVISED JANUARY 2004

description/ordering information (continued)

The MAX3232 device consists of two line drivers, two line receivers, and a dual charge-pump circuit with
±15-kV ESD protection pin to pin (serial-port connection pins, including GND). The device meets the
requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous communication
controller and the serial-port connector. The charge pump and four small external capacitors allow operation
from a single 3-V to 5.5-V supply. The devices operate at data signaling rates up to 250 kbit/s and a maximum
of 30-V/µs driver output slew rate.
Function Tables

EACH DRIVER
INPUT OUTPUT
DIN DOUT
L H
H L
H = high level, L = low
level

EACH RECEIVER
INPUT OUTPUT
RIN ROUT
L H
H L
Open H
H = high level, L = low
level, Open = input
disconnected or
connected driver off

logic diagram (positive logic)

11 14
DIN1 DOUT1

10 7
DIN2 DOUT2

12 13
ROUT1 RIN1

9 8
ROUT2 RIN2

2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265



 


    
 ±
    
SLLS410I − JANUARY 2000 − REVISED JANUARY 2004

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 6 V
Positive output supply voltage range, V+ (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 7 V
Negative output supply voltage range, V− (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.3 V to −7 V
Supply voltage difference, V+ − V− (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 V
Input voltage range, VI: Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 6 V
Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −25 V to 25 V
Output voltage range, VO: Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −13.2 V to 13.2 V
Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to VCC + 0.3 V
Package thermal impedance, θJA (see Notes 2 and 3): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73°C/W
DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . 82°C/W
DW package . . . . . . . . . . . . . . . . . . . . . . . . . . 57°C/W
PW package . . . . . . . . . . . . . . . . . . . . . . . . . 108°C/W
Operating virtual junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltages are with respect to network GND.
2. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable
ambient temperature is PD = (TJ(max) − TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
3. The package thermal impedance is calculated in accordance with JESD 51-7.

recommended operating conditions (see Note 4 and Figure 4)

MIN NOM MAX UNIT
VCC = 3.3 V 3 3.3 3.6
Supply voltage V
VCC = 5 V 4.5 5 5.5
VCC = 3.3 V 2
VIH Driver high-level input voltage DIN V
VCC = 5 V 2.4
VIL Driver low-level input voltage DIN 0.8 V
Driver input voltage DIN 0 5.5
VI V
Receiver input voltage −25 25
MAX3232C 0 70
TA Operating free-air temperature °C
MAX3232I −40 85
NOTE 4: Test conditions are C1−C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2−C4 = 0.33 µF at VCC = 5 V ± 0.5 V.

electrical characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (see Note 4 and Figure 4)
PARAMETER TEST CONDITIONS MIN TYP‡ MAX UNIT
ICC Supply current No load, VCC = 3.3 V or 5 V 0.3 1 mA
‡ All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
NOTE 4: Test conditions are C1−C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2−C4 = 0.33 µF at VCC = 5 V ± 0.5 V.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3



 


    
 ±
    
SLLS410I − JANUARY 2000 − REVISED JANUARY 2004

DRIVER SECTION

electrical characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (see Note 4 and Figure 4)
PARAMETER TEST CONDITIONS MIN TYP† MAX UNIT
VOH High-level output voltage DOUT at RL = 3 kΩ to GND, DIN = GND 5 5.4 V
VOL Low-level output voltage DOUT at RL = 3 kΩ to GND, DIN = VCC −5 −5.4 V
IIH High-level input current VI = VCC ±0.01 ±1 µA
IIL Low-level input current VI at GND ±0.01 ±1 µA
VCC = 3.6 V, VO = 0 V
IOS‡ Short-circuit output current ±35 ±60 mA
VCC = 5.5 V, VO = 0 V
ro Output resistance VCC, V+, and V− = 0 V, VO = ±2 V 300 10M W
† All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
‡ Short-circuit durations should be controlled to prevent exceeding the device absolute power dissipation ratings, and not more than one output
should be shorted at a time.
NOTE 4: Test conditions are C1−C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2−C4 = 0.33 µF at VCC = 5 V ± 0.5 V.

switching characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (see Note 4 and Figure 4)
PARAMETER TEST CONDITIONS MIN TYP† MAX UNIT
CL = 1000 pF, RL = 3 kΩ,
Maximum data rate 150 250 kbit/s
One DOUT switching, See Figure 1
RL = 3 kΩ to 7 kΩ,
tsk(p) Pulse skew§ CL = 150 pF to 2500 pF 300 ns
See Figure 2
Slew rate, transition region RL = 3 kΩ to 7 kΩ, CL = 150 pF to 1000 pF 6 30
SR(tr) V/µs
(see Figure 1) VCC = 3.3 V CL = 150 pF to 2500 pF 4 30
† All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
§ Pulse skew is defined as |tPLH − tPHL| of each channel of the same device.
NOTE 4: Test conditions are C1−C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2−C4 = 0.33 µF at VCC = 5 V ± 0.5 V.

4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265



 


    
 ±
    
SLLS410I − JANUARY 2000 − REVISED JANUARY 2004

RECEIVER SECTION

electrical characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (see Note 4 and Figure 4)
PARAMETER TEST CONDITIONS MIN TYP† MAX UNIT
VOH High-level output voltage IOH = −1 mA VCC−0.6 V VCC−0.1 V V
VOL Low-level output voltage IOL = 1.6 mA 0.4 V
VCC = 3.3 V 1.5 2.4
VIT+ Positive-going input threshold voltage V
VCC = 5 V 1.8 2.4
VCC = 3.3 V 0.6 1.2
VIT− Negative-going input threshold voltage V
VCC = 5 V 0.8 1.5
Vhys Input hysteresis (VIT+ − VIT−) 0.3 V
ri Input resistance VI = ±3 V to ±25 V 3 5 7 kW
† All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
NOTE 4: Test conditions are C1−C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2−C4 = 0.33 µF at VCC = 5 V ± 0.5 V.

switching characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (see Note 4 and Figure 3)
PARAMETER TEST CONDITIONS MIN TYP† MAX UNIT
tPLH Propagation delay time, low- to high-level output 300 ns
CL= 150 pF
tPHL Propagation delay time, high- to low-level output 300 ns
tsk(p) Pulse skew‡ 300 ns
† All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
‡ Pulse skew is defined as |tPLH − tPHL| of each channel of the same device.
NOTE 4: Test conditions are C1−C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2−C4 = 0.33 µF at VCC = 5 V ± 0.5 V.

PARAMETER MEASUREMENT INFORMATION

3V
Input 1.5 V 1.5 V
RS-232
Output 0V
Generator
(see Note B) 50 Ω
CL tTHL tTLH
RL (see Note A)
VOH
3V 3V
Output
−3 V −3 V
VOL

TEST CIRCUIT 6V VOLTAGE WAVEFORMS

SR(tr) +
t or t
THL TLH

NOTES: A. CL includes probe and jig capacitance.

B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.

Figure 1. Driver Slew Rate

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5



 


    
 ±
    
SLLS410I − JANUARY 2000 − REVISED JANUARY 2004

PARAMETER MEASUREMENT INFORMATION

3V
RS-232 Input 1.5 V 1.5 V
Generator Output 0V
(see Note B) 50 Ω
CL tPHL tPLH
RL (see Note A)
VOH
Output 50% 50%
VOL
TEST CIRCUIT VOLTAGE WAVEFORMS

NOTES: A. CL includes probe and jig capacitance.

B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.

Figure 2. Driver Pulse Skew

3V
Input 1.5 V
1.5 V
Output −3 V
Generator
(see Note B) 50 Ω tPHL tPLH
CL
(see Note A)
VOH
Output 50% 50%
VOL
TEST CIRCUIT VOLTAGE WAVEFORMS
NOTES: A. CL includes probe and jig capacitance.
B. The pulse generator has the following characteristics: ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns.

Figure 3. Receiver Propagation Delay Times

6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265



 


    
 ±
    
SLLS410I − JANUARY 2000 − REVISED JANUARY 2004

APPLICATION INFORMATION

1 VCC 16
C1+
+ CBYPASS
− = 0.1µF
+ 2 15
C1 V+ GND
− †+
C3
−
14
3 DOUT1
C1−

13
4 RIN1
C2+
+
C2 5 kΩ
−
5 C2−

12
ROUT1
6
V− 11
−
C4 DIN1
+
7 10
DOUT2 DIN2

8 9
RIN2 ROUT2

5 kΩ

† C3 can be connected to VCC or GND.

NOTES: A. Resistor values shown are nominal.
B. Nonpolarized ceramic capacitors are acceptable. If polarized tantalum or electrolytic capacitors are used, they should be
connected as shown.

VCC vs CAPACITOR VALUES

VCC C1 C2, C3, C4

3.3 V ± 0.3 V 0.1 µF 0.1 µF

5 V ± 0.5 V 0.047 µF 0.33 µF
3 V to 5.5 V 0.1 µF 0.47 µF

Figure 4. Typical Operating Circuit and Capacitor Values

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7

 PACKAGE OPTION ADDENDUM
www.ti.com 4-Mar-2005

PACKAGING INFORMATION

Orderable Device Status (1) Package Package Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Type Drawing Qty
MAX3232CD ACTIVE SOIC D 16 40 Pb-Free CU NIPDAU Level-2-260C-1 YEAR/
(RoHS) Level-1-235C-UNLIM
MAX3232CDB ACTIVE SSOP DB 16 80 Pb-Free CU NIPDAU Level-2-260C-1 YEAR/
(RoHS) Level-1-235C-UNLIM
MAX3232CDBR ACTIVE SSOP DB 16 2000 Pb-Free CU NIPDAU Level-2-260C-1 YEAR/
(RoHS) Level-1-235C-UNLIM
MAX3232CDR ACTIVE SOIC D 16 2500 Pb-Free CU NIPDAU Level-2-260C-1 YEAR/
(RoHS) Level-1-235C-UNLIM
MAX3232CDW ACTIVE SOIC DW 16 40 Pb-Free CU NIPDAU Level-2-250C-1 YEAR/
(RoHS) Level-1-235C-UNLIM
MAX3232CDWR ACTIVE SOIC DW 16 2000 Pb-Free CU NIPDAU Level-2-250C-1 YEAR/
(RoHS) Level-1-235C-UNLIM
MAX3232CPW ACTIVE TSSOP PW 16 90 Pb-Free CU NIPDAU Level-1-250C-UNLIM
(RoHS)
MAX3232CPWR ACTIVE TSSOP PW 16 2000 Pb-Free CU NIPDAU Level-1-250C-UNLIM
(RoHS)
MAX3232ID ACTIVE SOIC D 16 40 Pb-Free CU NIPDAU Level-2-260C-1 YEAR/
(RoHS) Level-1-235C-UNLIM
MAX3232IDB ACTIVE SSOP DB 16 80 Pb-Free CU NIPDAU Level-2-260C-1 YEAR/
(RoHS) Level-1-235C-UNLIM
MAX3232IDBR ACTIVE SSOP DB 16 2000 Pb-Free CU NIPDAU Level-2-260C-1 YEAR/
(RoHS) Level-1-235C-UNLIM
MAX3232IDR ACTIVE SOIC D 16 2500 Pb-Free CU NIPDAU Level-2-260C-1 YEAR/
(RoHS) Level-1-235C-UNLIM
MAX3232IDW ACTIVE SOIC DW 16 40 Pb-Free CU NIPDAU Level-2-250C-1 YEAR/
(RoHS) Level-1-235C-UNLIM
MAX3232IDWR ACTIVE SOIC DW 16 2000 Pb-Free CU NIPDAU Level-2-250C-1 YEAR/
(RoHS) Level-1-235C-UNLIM
MAX3232IPW ACTIVE TSSOP PW 16 90 Pb-Free CU NIPDAU Level-1-250C-UNLIM
(RoHS)
MAX3232IPWR ACTIVE TSSOP PW 16 2000 Pb-Free CU NIPDAU Level-1-250C-UNLIM
(RoHS)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.

(2)
Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional
product content details.
None: Not yet available Lead (Pb-Free).
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens,
including bromine (Br) or antimony (Sb) above 0.1% of total product weight.

(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder
temperature.

Addendum-Page 1
 PACKAGE OPTION ADDENDUM
www.ti.com 4-Mar-2005

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.

Addendum-Page 2
 MECHANICAL DATA

MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001

DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE

28 PINS SHOWN

0,38
0,65 0,15 M
0,22
28 15

0,25
0,09
5,60 8,20
5,00 7,40

Gage Plane

1 14 0,25

A 0°–ā8° 0,95
0,55

Seating Plane

2,00 MAX 0,05 MIN 0,10

PINS **
14 16 20 24 28 30 38
DIM

A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90

A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30

4040065 /E 12/01

NOTES: A. All linear dimensions are in millimeters.

B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-150

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

 MECHANICAL DATA

MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999

PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE

14 PINS SHOWN

0,30
0,65 0,10 M
0,19
14 8

0,15 NOM
4,50 6,60
4,30 6,20

Gage Plane

0,25
1 7
0°– 8°
A 0,75
0,50

Seating Plane

1,20 MAX 0,15 0,10

0,05

PINS **
8 14 16 20 24 28
DIM

A MAX 3,10 5,10 5,10 6,60 7,90 9,80

A MIN 2,90 4,90 4,90 6,40 7,70 9,60

4040064/F 01/97

NOTES: A. All linear dimensions are in millimeters.

B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

 IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.

Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:

Products Applications
Amplifiers amplifier.ti.com Audio www.ti.com/audio
Data Converters dataconverter.ti.com Automotive www.ti.com/automotive
DSP dsp.ti.com Broadband www.ti.com/broadband
Interface interface.ti.com Digital Control www.ti.com/digitalcontrol
Logic logic.ti.com Military www.ti.com/military
Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork
Microcontrollers microcontroller.ti.com Security www.ti.com/security
Telephony www.ti.com/telephony
Video & Imaging www.ti.com/video
Wireless www.ti.com/wireless

Mailing Address: Texas Instruments

Post Office Box 655303 Dallas, Texas 75265

Copyright  2005, Texas Instruments Incorporated