Modular Lube® Lubrication Systems

Divider Valves

UV Divider
Valves

UV Divider Valves are designed to meter oil or grease in automatic or manual systems installed on all types of industrial
machinery. Segmented baseplate assembly contains all inlet and outlet connections. Alternate outlet ports are located on
the face of the divider valve which may be used for installation of performance indicators.

Specifications:
Max. Inlet Section Intermediate Section
Max. Oper.
Lube Performance Material of Seal
press.
Points/ Model Thread Model Thread Indicator Port* Construction Construction
psig / bar
Assembly
Yellow chromate
16 3500 / 240 87918 ¼" NPSF(F) 87919 ⅛" NPSF(F) ⅛" NPSF(F) Flouroelastomer
plated steel
* Can also be used as an alternate outlet port.

UV Baseplate and Tie Rod Specifications:

Dimensions
Max. No. of No. of Divider End Tie
Outlets Valves Section Rod* A A B B
in. mm in. mm
6 3 250290 3.58 90.9 4.52 114.8
8 4 250291 4.5 114.3 5.44 138.2
10 5 250292 5.42 137.7 6.36 161.5
87920
12 6 250293 6.34 161.0 7.28 184.9
14 7 250294 7.27 184.6 8.20 208.3
16 8 250295 8.19 208.0 9.13 231.9
* Each tie rod model number includes three tie rods and three fastening nuts.
Note: Use 68645 closure plug (⅛" NPT) to plug non-working outlets.

UV Divider Valve Specifications:

Single Outlet Twin Outlet
Lubricant Output Lubricant output
Model Number Model Number
per Outlet per Outlet
Designation W/Right Designation W/Right
Standard Standard
Side Cycle cu. in. cc Side Cycle cu. in. cc
Model Model
Indicator Indicator
05S 882051 — .010 .164 05T 882052 — .005 .082
10S 882101 — .020 .328 10T 882102 — .010 .164
15S 882151 — .030 .492 15T 882152 — .015 .246
20S 882201 882203 .040 .656 20T 882202 882204 .020 .328
25S 882251 882253 .050 .820 25T 882252 882254 .025 .410
30S 882301 882303 .060 .983 30T 882302 882304 .030 .492
35S 882351 882353 .070 1.147 35T 882352 882354 .035 .574
40S 882401 882403 .080 1.311 40T 882402 882404 .040 .656
Model 882000 UV Bypass Block Optional by-pass block permits addition or deletion of lubrication points without disturbing existing installations. Includes mounting
screws and Buna-N seals.

4
Modular Lube® Lubrication Systems
Divider Valves
1.87"
48mm 3.38"
MC²-HP Divider 86mm

Valves

1.87"
48mm

MC²-HP High Pressure Divider Valves are designed to dispense either petroleum-based or synthetic lubricants in gas engine
and compressor lubrication systems.
Segmented baseplate assembly contains all inlet and outlet connections. Alternate outlet ports are located on the face of the
divider valve which may be used for installation of performance indicators.

Specifications:
Maximum Maximum
Lube Lube Performance Material of Seal
Lube Points/ Operating Press.
Inlet Outlet Indicator Port Construction Construction
Assembly psig / bar
Black chromate
16 7500 / 512 ¹⁄₄" NPTF(F) ¹⁄₈" NPSF(F) ⁵⁄₁₆" - 24 UNF Flouroelastomer
plated steel
* Can also be used as an alternate outlet port.

MC²-HP Baseplate and Tie Rod Specifications:

Intermediate Dimensions
Maximum Number Number of Inlet End Tie Rod*
Section A
of Outlets Divider Valves Section Section (Qty Req'd)
(Qty Req'd) in. mm
6 3 236640 (3) 87957 (3) 5.09 129
8 4 236641 (3) 87957 (4) 6.00 152
10 5 236642 (3) 87957 (5) 6.91 176
87955 87956
12 6 236643 (3) 87957 (6) 7.81 198
14 7 236644 (3) 87957 (7) 8.72 221
16 8 236645 (3) 87957 (8) 9.63 245
* Each tie rod model number includes three tie rods.
Note: Use 68645 closure plug (⅛" NPT) to plug non-working outlets. Each 87956 end section contains three tie rod nuts

MC²-HP Divider Valve Specifications:

Single Outlet Twin Outlet
Lubricant Output Lubricant Output
Model Number Model Number
per Outlet per Outlet
Designation W/Right Designation W/Right
Standard
Side Cycle cu. in. cc Standard Side Cycle cu. in. cc
Model
Indicator Indicator
06S 876061 - .012 .196 06T 876062 - .006 .098
09S 876091 - .018 .295 09T 876092 - .009 .147
12S 876121 876123 .024 .393 12T 876122 876124 .012 .197
18S 876181 876183 .036 .590 18T 876182 876184 .018 .295
24S 876241 876243 .048 .787 24T 876242 876244 .024 .393
Model 874000 MC²-HP Bypass Block Optional by-pass block permits addition or deletion of lubrication points without disturbing existing installations. Includes
mounting screws and flouroelastomer gasket plate.

5
Modular Lube® Lubrication Systems
Divider Valves

XL Divider Valves

XL Divider Valves are designed to meter large volumes of oil or grease in manual or automatic lubrication systems for all types
of industrial machinery. These units can be used in complete XL systems or integrated as a primary divider valve assembly in
systems using UV divider valves as secondaries.
Solid one piece baseplate contains all inlet and outlet connections. Convenient front located ports on the divider valve are
provided for installation of any desired performance indicators.

Specifications:
Maximum Maximum
Lube Lube Performance Material of Seal
Lube Points/ Operating Press.
Inlet Outlet Indicator Port* Construction Construction
Assembly psig / bar
12 2500 / 172 ³⁄₈" NPTF(F) ¹⁄₄" NPTF(F) ¹⁄₈" NPTF(F) Zinc plated steel Buna-N
* Can also be used as an alternate outlet port.

XL Baseplate Specifications:
Dimensions
Maximum Number of No. of Divider
Model No. A
Outlets Valves*
in. mm
87030-3 6 3 5.34 136
87030-4 8 4 6.69 170
87030-6 12 6 9.38 238
* Use No.67359 closure plug (¼” NPT) to plug non-working outlets.

XL Divider Valve Specifications:

Single Outlet Twin Outlet
W/Right Total Lubricant Total
Standard Output W/Right Lubricant
Designation Side Cycle Standard
Model Designation Side Cycle Output
Indicator cu. in. cc Model
Indicator
30S 87026-03S - .060 .983 cu. in. cc
50S 87026-05S - .100 1.64 30T 87026-03T - .030 .492
80S 87026-08S - .160 2.62 50T 87026-05T - .050 .820
100S 87026-10S - .200 3.28 80T 87026-08T - .080 1.31
120S 87026-12S - .240 3.93 100T 87026-10T - .100 1.64
150S 87026-15S - .300 4.92 120T 87026-12T - .120 1.97
150T 87026-15T - .150 2.46

Model 87028 XL Bypass Block Optional by-pass block permits addition or deletion of lubrication points without disturbing existing installations. Includes mounting
screws and flouroelastomer o-ring seals.

6
Modular Lube® Lubrication Systems
UV, XL & MC Divider Valve Accessories

UV, XL Divider Valve Accessories

Atmospheric Safety Relief Indicators
High pressure ruptures disc, pressure and lubricant vents to the atmosphere.
Pressure Rating Replacement
UV, XL Disc
Disc Model Connector
Model psig bar Color
(10/pkg)
87934 1450 100 Yellow 69813-10
87935 1750 120 Red 69813-12
⅛" NPTF(M)
87936 3250 224 Purple 250312
87937 3700 255 Yel/Nat 250313

Reset-Type Performance Indicators

High pressure extends indicator. Reset the indicator after pressure is relieved.
Pressure Rating
UV, XL Model Connector
psig bar
87938 500 34
87939 1000 69
87940 1500 103 ⅛" NPTF(M)
87941 2000 138
87942 3000 207
Note: O-rings are flouroelastomer

Adapter
Adapter connects UV, XL style performance indicators to MC2 style divider valves
and old style ML. Includes flouroelastomer O-ring.
Model Thread
87915 ⁵⁄₁₆" -24 Male x ⅛" NPTF(F)

MC2 Divider Valve Accessories

Pin Type Performance Indicators
High pressure ruptures internal disc and extends indicator.
Pressure Rating Replacement
MC Disc
Disc Model Connector
Model psig bar Color
(10/pkg)
87895 1450 109 Yellow 69813-10
87896 1750 120 Red 69813-12 ⁵⁄₁₆"-24 Male
87897 2050 141 Orange 69813-14
Note: O-rings are flouroelastomer
Reset-Type Performance Indicators
High pressure extends indicator. Reset the indicator after pressure is relieved.
Pressure Rating Spring/Tag
Model Connector
psig bar Color
87885 1000 69 Green
87886 1500 103 Yellow
87887 2000 138 Red ⁵⁄₁₆"-24 Male
87888 2500 172 Orange
87889 3000 207 Blue
Note: O-rings are flouroelastomer

7
Modular Lube® Lubrication Systems
Divider Valve Accessories

Cycle Switch for Natural Gas Compressors

Designed to work with Lincoln MC, MC² HP valves as wel as with other brands. Simple
installation reduces labor costs. Features captured magnet assembly and hall effect switch.
Cycle Switch with Shutdown Feature
• Lower-cost, stand-alone solution
• Shut down protection for “no flow” conditions is factory set at two minutes
• Operates from 5-30 VDC for increased reliability
Maximum Temperature
Part Power EX
Description Working Material
No. Req. Range Rating
Pressure
Hall Effect/Cycle
Switch with
249123 Shutdown for Approval
Lincoln MC²-HP pending
Aluminum
series block for Class
Housing,
-40°C to 85°C I, Groups
Hall Effect/Cycle 5 to 30 VDC, Stainless
7500 psi (-40°F to A, B, C &
Switch with 100 UA max. Steel
185°F) D, Div. 1
Shutdown for Magnet & 2 CE,
249124 Lincoln UV and Assembly II 3G Ex
Graco Lubriquip®- Na IIA
Manzel MHP series
style block

Cycle Switch
Cycle Switch attaches to valve with cycle indicator pin, sends electrical signal to
controller.
Conduit
Model Switch Type Switch Capacity Connector
15 Amps @ 125/250 VAC
87070 SPDT ¹⁄₂" - 14 NPSM
0.5 Amps @ 125 VDC

Cycle Counter
Cycle Counter attaches to valve with cycle indicator pin, counts and records cycles.
Model Maximum Counts
87828 99,999

Proximity Switch
Cycle Switch for Natural Gas Compressors
Block Style Switch Switch Conduit
Model CSA Certification
Type Capacity Connector
85651 UV
10 Watts Class l, Group A, B, C & D
87617* MC
SPST 200 VDC / Class ll, Group E, F & G ¹⁄₂" NPT(F)
XL Size 03 0.5 Amp Hazardous Locations
87618
thru12
*Can be used with Model 87630 Datalogger Lubrication Monitor

External Singling/Cross Port Kit

External Cross Port Kit connects alternate outlet ports to combine the volume of two
divider valves through a single outlet.
Model Block Type Application/Usage
87905 MC Single and Crossport
87823 XL Crossport
87824 XL Singling
87825 UV Crossport

Balancing Valve
Model 87865 Balancing Valve is used when back pressure differential between divider
valve outlets exceeds 1000 psi (69 bar).
Pressure Adjustment
Inlet/
Model Min Max Seal Material
Outlet
psig bar psig bar
87865 250 17 6000 414 ¹⁄₈" NPTF(F) Flouroelastomer

8
Modular Lube® Lubrication Systems
Divider Valve Accessories

Mounting Bracket
Model 250286 (UV) and Model 360675 (MC2) Mounting Brackets—
Mount divider valve assembly off the face of vertical surfaces. Use two brackets per
divider valve assembly.

Check Valves
Check valves maintain prime in feed lines and check back pressure from pressurized
lubrication points.

Double Ball, Straight

Pressure Hex Hex Hex Length
Model Inlet Outlet
Max Opening Material Inlet-in. Outlet-in. in./mm
Carbon
880511 ¹⁄₄" ¹⁄₄" 3.72/94.5
Steel
NPTF(F) NPTF(M)
880518-9 8000 psig 145 psig 316 S.S. 3.75/95.3
¹³⁄₁₆"
552 bar 10 bar Carbon
880517 ¹⁄₈" ¹⁄₈" ¾" 3.31 /
Steel
NPTF(F) NPTF(M) 84.1
880519-9 316 S.S.
5000 psig 80 psig ⁹⁄₁₆-18 ⁷⁄₁₆-20 Stainless
880015-9 ¾" 2.75/70
345 bar 6 bar UNF (M) UNF (M) Steel

Ball & Poppet, Straight

Pressure Hex Hex Hex Length
Model Inlet Outlet
Max Opening Material Inlet-in. Outlet-in. in./mm
¹⁄₈" ¹⁄₈" 2.75
880513
2000 psig 50 psig NPTF(F) NPTF(M) Carbon 70.0
¾" ¹³⁄₁₆"
138 bar 3.5 bar ¹⁄₄" ¹⁄₄" Steel 3.06
880514
NPTF(F) NPTF(M) 77.7

Ball Type, Straight

Pressure Hex Hex Length
Model Inlet Outlet
Max Opening Material in. in./mm
87817 7500 psig 20-70 psig ¹⁄₄" NPTF(M) ¹⁄₄" NPSF(F) ¹¹⁄₁₆" 1.38/35.1
87818 517 bar 1.5-5 bar ¹⁄₈" NPTF(M) ¹⁄₈" NPTF(F) Carbon ⁹⁄₁₆" 1.19/30.2
6000 psig 31-70 psig Steel
130021-3 ¹⁄₈" NPTF(F) ¹⁄₈" NPTF(M) ½" 1.06/27.0
414 bar 2-5 bar

Ball & Poppet, 90°

Pressure Hex Hex Dimensions
Hex in. / mm
Model Inlet Outlet Inlet- Outlet-
Material
Max Opening in. in. A B
2000 psig 50 psig ¹⁄₈" ¹⁄₈" Carbon 3.38 1.25
880515 ¾" ¹³⁄₁₆"
138 bar 3.5 bar NPTF(F) NPTF(M) Steel 86 31.8