0% found this document useful (0 votes)
46 views2 pages

G RC/RL Step-by-Step Procedure: TH Eq Eq TH

This document outlines a 7-step procedure for solving RC and RL circuits: 1) Express voltages and currents using a general exponential form involving the time constant tau, equivalent capacitance or inductance, and initial and final values. 2) Remove the C or L and find the Thevenin resistance RTh. 3) At t=0-, assume zero derivatives and model C as open and L as wire. 4) Find the initial energy variable value, vC(t=0-) or iL(t=0-). 5) Set the initial value as the C voltage or L current at t=0+. 6) Use the t=0+ model to find

Uploaded by

Dileep G
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
46 views2 pages

G RC/RL Step-by-Step Procedure: TH Eq Eq TH

This document outlines a 7-step procedure for solving RC and RL circuits: 1) Express voltages and currents using a general exponential form involving the time constant tau, equivalent capacitance or inductance, and initial and final values. 2) Remove the C or L and find the Thevenin resistance RTh. 3) At t=0-, assume zero derivatives and model C as open and L as wire. 4) Find the initial energy variable value, vC(t=0-) or iL(t=0-). 5) Set the initial value as the C voltage or L current at t=0+. 6) Use the t=0+ model to find

Uploaded by

Dileep G
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

By: Neil E.

Cotter RLC CIRCUITS


GENERAL RC/RL SOLUTION
Step-by-Step Procedure

TOOL: The following step-by-step procedure may be used to solve RC or RL circuit


problems.
i) Every voltage or current in an RC or RL circuit after time t = 0 may be
expressed in the following general form:
v(t) = [v(t = 0+ ) − v(t → ∞)]e−t / τ + v(t → ∞)
or
i(t) = [i(t = 0+ ) − i(t → ∞)]e−t / τ + i(t → ∞)
where τ ≡ RTh Ceq or τ ≡ Leq /RTh as appropriate, and
RTh ≡ Thevenin equivalent resistant for circuit (after t = 0) seen from
terminals where C or L is connected (without the C or L present)
Ceq ≡ equivalent capacitance of capacitors in series or parallel
Leq ≡ equivalent inductance of inductors in series or parallel

ii) To find RTh, remove the C or L from the circuit and find the Thevenin resistance
of the circuit seen looking into the circuit from the terminals where the C or L
was attached. Use the circuit for t > 0.
iii) At time t = 0–, assume the circuit has been stable for a long time, causing
derivative values to become zero:
dvC (t) diL (t)
= 0 and =0
dt dt
This means that iC (t = 0− ) = 0 A and v L (t = 0− ) = 0 V , which in turn means
that a C looks like an open circuit and an L looks like a wire. Thus, the circuit
model for t = 0 has C's replaced with open circuits and L's replaced with wires.
iv) Find vC (t = 0− ) or iL (t = 0− ) . These are the energy variables that will not
change as a switch or source changes state at time t = 0, and they must be
known in order to determine initial conditions for the general solution of the
circuit. No other values in the circuit are guaranteed to stay the same at time
t = 0+, so find only the value of vC (t = 0− ) or iL (t = 0− ) at time t = 0–.
v) Set vC (t = 0+ ) = vC (t = 0− ) or iL (t = 0+ ) = iL (t = 0− ) . At t = 0+, model a
capacitor as a voltage source with value vC (t = 0− ) , and model an inductor as a
current source with value iL (t = 0− ) .
CONC EPTUAL TOOLS
By: Neil E. Cotter RLC CIRCUITS
GENERAL RC/RL SOLUTION
Step by Step Procedure (cont.)

vi) Using the circuit model for t = 0+ with the C or L modeled as described in (iii),
find the value of v(t = 0+ ) or i(t = 0+ ) .
vii) For t→∞, assume the circuit has been stable for a long time, as in (iii), and
replace C's with open circuits and L's with wires. Find vC (t → ∞) or
iL (t → ∞) .

You might also like