Manual XMR401HDS

User manual for XMR401HDS
User Manual
For
;05+'6
Mobile Digital Video Recorder
1 - 73
Notice
The information in this manual was current when published. The manufacturer reserves the right to
revise and improve its products. All specifications are therefore subject to change without any notice.
The purpose of this manual is to kindly aid the user for the operation for our MDVR. The user should
have a basic understanding of computer operation and basic knowledge of how to connect peripherals
and make some settings.
Copyright
Under copyright laws, the content of this manual may not be copied, photocopied, reproduced,
translated or reduced to any electronic medium or machine- readable form, in whole or in part, without
prior written consent of Streamax Technology Co., Ltd. Copyright (2013-2015)
2 -73
Guarantee & Warnings

1) Electrical Apparatus Safety
All installation and operation should comply with local electrical safety norms.
2) Transportation
In the process of transportation, storage and installation, please avoid heavy stress, violent vibration,
impact and water splashing.
3) Installation
Install the equipment in accordance with the requirements, handle carefully. Do not heavily press the
equipment before the MDVR installation is finished.
4) Requirements on Engineers & Technicians
All the work of checking and maintenance should be done by qualified technicians and engineers.
We do not undertake any responsibility caused by unauthorized modifications.
5) Requirements on Environment
The equipment should be installed and stored in a cool and dry place, away from direct sunlight,
flammable or explosive substances, etc. Keep gaps not less than 3cm around the device to facilitate
ventilation for cooling.
6) Accessories
Make sure to use accessories from the manufacturer recommended in the attachment.
Insulate circuit ground and metal shell for all the peripherals.
Before installation, please open the package and ensure that all parts are included.
If there are any problems, please contact us as soon as possible.
3-73
Contents
1. PRODUCT CHARACTERISTICS................................................................................................................... 6
1.1. OVERVIEW.........................................................................................................................................6
1.2. SPECIFICATIONS............................................................................................................................. 6
1.3. SYSTEM DIAGRAM..........................................................................................................................8
1.4. EXTERNAL INTERFACE................................................................................................................. 8
1.5. HARD DISK INSTALLATION......................................................................................................... 11
1.6. SIM CARD INSTALLATION........................................................................................................... 12
1.7. DEFINITION AND PICTURES OF EXTERNAL CABLES........................................................ 13
2. LOCAL MANAGEMENT................................................................................................................................. 14
2.1. LOGIN INTERFACE........................................................................................................................ 14
2.2. RECORD SEARCH:........................................................................................................................17
2.3. LOG SEARCH.................................................................................................................................. 20
2.4. SYSTEM STATUS........................................................................................................................... 22
2.5. BASIC SETUP..................................................................................................................................24
2.5.1. REGISTER INFOMATION (SETUP VEHICLE INFORMATION).....................................24
2.5.2. TIME SETUP............................................................................................................................ 26
2.5.3. START UP.................................................................................................................................28
2.5.4. USER SETUP...........................................................................................................................29
2.5.5. NETWORK................................................................................................................................30
2.5.6. APPLICATION..........................................................................................................................34
2.6. SURVEILLANCE..............................................................................................................................34
2.6.1. LIVE VIEW................................................................................................................................ 35
2.6.2. RECORD...................................................................................................................................36
2.6.3. IPC SETUP............................................................................................................................... 40
2.6.4. PTZ.............................................................................................................................................42
2.7. DATA COLLECTION........................................................................................................................42
2.7.1. GENERAL................................................................................................................................. 42
2.7.2. SNAP SETTING.......................................................................................................................44
2.7.3. ECO-DRIVING ....................................................................................................................... 46
2.8. ALARM.............................................................................................................................................. 47
2.8.1. BASE..........................................................................................................................................47
2.8.2. VIDEO........................................................................................................................................54
2.8.3. ADVANCE................................................................................................................................. 57
2.9. MAINTENANCE............................................................................................................................... 58
2.9.1. CONFIGURATION...................................................................................................................59
2.9.2. DATA EXPORT.........................................................................................................................59
2.9.3. UPGRADE................................................................................................................................ 60
2.9.4. STORAGE.................................................................................................................................61
2.9.5. DEFAULT.................................................................................................................................. 62
3. WEB MANAGEMENT..................................................................................................................................... 62
3.1. LOGIN INTERFACE........................................................................................................................ 62
3.2. MAIN INTERFACE...........................................................................................................................63
4-73
3.3. PLAYBACK....................................................................................................................................... 64
3.4. MAINTENANCE............................................................................................................................... 66
3.4.1. BASIC INFORMATION........................................................................................................... 67
3.4.2. DEVICE MODULE...................................................................................................................67
3.4.3. STORAGE DEVICE................................................................................................................ 68
3.4.4. VERSION INFORMATION..................................................................................................... 69
3.5. CONFIGURATION...........................................................................................................................69
4. STORAGE CAPACITY CALCULATION.......................................................................................................71
5. FREQUENTLY ASKED QUESTIONS.......................................................................................................... 72
5-73
1. PRODUCT CHARACTERISTICS
1.1. OVERVIEW
Streamax X1-H0401 is a functional Mobile Digital Video Recorder specially designed for vehicle
video surveillance and remote monitoring. It has a high-speed processor and embedded operating
system, combining with the most advanced H.264 video compression / decompression technology,
3G/4G network, GPS positioning technology, as well as WIFI. It supports not only video recording in
720P, WD1, WHD1, WCIF, D1, HD1 and CIF formats, but also vehicle travel information recording and
wireless data upload. With center software it also achieves alarm linkage central monitoring, remote
management and playback analysis. It is easy to use with simple design, multi-functions, superior
anti-vibration, flexible installation and high reliability.
1.2. SPECIFICATIONS
Function Overview Preview, Recording, Playback, Network, Locating
OS Linux 3.0.8
System
Control Mode Easy Check, network, CP4, mouse (3G/4G/WIFI)
Input 4 channels WD1+1 channel 720P
Output 1 channel
(4x25)FPS WD1 @ PAL / (4x30)FPS WD1 @ NTSC
Video Total Resource
+30FPS 720P
Electrical level: 1Vpp Impedance: 75Ω NTSC/PAL
Video Signal Standard
Optional
Input 5channels (1 channel IPC audio input)
Audio Output 1channel
Audio Signal Standard Electrical level: 2Vpp Input impedance: 4.7kΩ
Display Split 1/4
GPS information, alarm, vehicle No., speed,
Display OSD
date/time
Operation Interface Semi-transparent GUI
Video: H.264
Video/Audio Compression
Audio: ADPCM, G.711A , G.711U
Analog:
PAL:WD1(928X576),WHD1(928X288),
WCIF(464X288),D1(704X576),HD1(704x288),
Recording CIF(352x288);
Image Resolution NTSC:WD1(928X480),WHD1(928X240),
WCIF(464X240),D1(704x480),HD1(704x240),
CIF(352x240);
Digital:
720P(1280X720);
6-73
Image Quality 1-8 levels adjustable (1 is the best)

Recording Mode Boot up/Manual/Schedule/Alarm
Pre-recording 0-60minutes
Post-recording 0-30 minutes
Playback Channel 1 channel by local playback
Playback
Search Mode Date/time, channel, event
3G/4G EVDO/WCDMA/TDD-LTE/FDD-LTE
WIFI 802.11b/g/n
Network
Network connection WIFI/3G/4G optional
IPC Ethernet 6-pin M12( 10/100M x 1, PON power supply)
Locating GPS Location tracking, speed detection and time sync
Storage Hard Disk 2.5" SATA hard disk x 1
USB USB2.0 x 1
SIM SIM slot x 1
RS232 RS232 x 1 3pin
Interface Sensor 8 inputs, 2 outputs
Speed 1 channel pulse speed detection
Control panel CP4 optional
Intercommunication I mic interface
Input DC8-36V,Ignition signal
Output 5V@1A
Power
Max Power Consumption 32W
Standby Power Consumption ≈0W
Physical Dimension (L × W × H)(mm) 206.0 x 170.0 x 70.4
Characteristic Weight (with hard disk) 1.24Kg
Operating Temperature -40℃- +70℃(With heater) or -10℃- +70℃
Environment
Operating Relative Humidity 8%-90%（No Condense）
7-73
1.3. SYSTEM DIAGRAM
1.4. EXTERNAL INTERFACE

DIMENSION (Unit: mm)
8-73
9-73
FRONT PANEL
Serial No. Description

1 Hard disk module
2 Lock
3 Status LED
4 USB interface
REAR PANEL
Serial No. Print Description

1 Power DC 8-36 V Power Input
2 Sensor & Serial The Interfaces of Serial Port and Switch
3 A/V IN1~4 Audio & Video Input 1-4
4 A/V OUT Audio & Video Output
5 IPC The Interface of PON Power Supply
6 GPS Antenna Interface
7 3G/4G/WIFI Antenna Interface
10-73
1.5. HARD DISK INSTALLATION
11-73
1.6. SIM CARD INSTALLATION
12-73
1.7. DEFINITION AND PICTURES OF EXTERNAL CABLES

ALARM CABLE DEFINITION
Alarm and Serial Cables A/V OUT Cable
13-73
2. LOCAL MANAGEMENT
N9M supports 3 kinds of local setting methods:
1) Connect monitor to mobile DVR and make sure it can play real time output image. Then connect
mouse to USB interface at the front panel to have MDVR parameter setting.
2) Connect the touch panel CP4 to mobile DVR to have MDVR parameter setting. (RS232 serial port is
needed when they are model X1 and M1, while model X3, X5 and X7 can connect to the panel
interface directly.)
3) Model X5 supports MDVR parameter setting via remote controller.
2.1. LOGIN INTERFACE

When operate the device, user needs to have permission certified.
1) Press the remote control 【LOGIN / LOCK】or【SETUP】, the login screen will pop up.
2) Right click the mouse, the shortcut menu will pop up, left click login picture, login screen will pop up.
3) Left click on the login button to login and right click to log out.
14-73
Login Notice:
1) Software is automatically assigned by user name and password, it can be divided into user and
administrator privileges.
2) Password options cannot be closed, but it can be set to null; when it is empty, user do not need to
enter the password to login。
Login interface Introduction:
 User name：
1) Select users from the drop-down box. There are admin and user as defaults.
2) Currently, it can show two users and one admin.
 Password：
1) User can enter the operation interface if entering the right password;
2) User must enter the right password again if entering the wrong ones;
3) Click cancel to exit the login interface;
 Language：
1) It supports language switch. "language" (Lang) means the current interface adopts Chinese;
2) It will automatically switch once selecting the language.
3) Currently, it supports Chinese and English;
4) After switching languages, it will not restore language option when user restores the factory
Settings;
Default password and permission table is as follows:

Default Password Related User Related Authority
admin admin All Authorities
User user Search and playback
The password input Instruction:

1) User can set password with remote controller (only applicable to model X5), mouse or touch panel
CP4. Move cursor to password, click Enter and enter the right number.
15-73
2) Move the cursor to the number position, press 【 Enter 】 or left click mouse button to select the
corresponding number.
3) Move the cursor to 【123】, press 【Enter】or mouse to choose input type, such as numbers, letters,
or special characters.
4) 【ab】means lower case letters,【123】means numbers,【AB】means capital letters; the highlighted
place of background refers to the current cursor position.
5) Move Cursor to , Press【Enter】or left click mouse to move between the contents that have
entered.
6) Move Cursor to , Press 【Enter】or left click mouse to delete the previous input contents.
7) Move Cursor to , Press 【Enter】or the left click mouse to exit the keypad, the entered
contents will be written to the edit box.
8) Move Cursor to【Esc】 position, Press【Enter】or the left click mouse to exit the keypad, the entered
contents will not be written to the edit box.
16-73
Main interface
2.2. RECORD SEARCH:

Video search interface contains video file search, video data backup and video playback function.
When there is a hard disk or SD card, enter the video search interface. Following is the REC Search
interface:
In the calendar, the color below the dates means:

a. No color means no video.
b. Green means common video.
c. Red means alarm video.
d. Yellow means there are alarms and the video files are automatically lock (lock video).
Source: select the source of the video, there are main video, sub video and mirror video.
The main record means HDD record while sub record and mirror record are dual-stream records.
17-73
Select the date with record, click next, and then enter the following interface:
Following are the search options and search result interface:
Video type: User can choose all record, alarm record or normal record.
Channel: The channel is optional and mark with color that has record. The channel with gray cannot be
chosen if there is no record. As to different record type, it will show different relates.
Click search button in the record search detail page, user can enter then record search result page.
Time Bar: Time bar shows three time points, 0 o'clock, 12 o'clock, 24 o'clock. It shows what type of
videos during the time according to the marked channel.
Channel No: According to the situation of video for each channel video the day, the video will be
displayed on the time line. Tick the channel if user wants to playback the video.
Note: channel number is displayed from 1~20, please up page up/page down button to change channel
Button description
Video playback: Choose the channel No., select start time to play < default start from 0 >, click the
playback button to playback the video.
18-73
In playback interface, user can choose fast forward or fast backward to play the video, the button in the
middle of screen can switch the channels. The image stops and it will not exit automatically when
playing to the last video of the day.
Time period settings: Click the time setting button, select start time and end time, it will back up or
playback the video in the selected time period. Click clip to export the video, the file format can
be.264< comprehensive file >, also can be.avi format.
Video export: Select the channel that has the video files, click this button, all the video files in the
effective time period will be exported to the external USB peripherals, file format can
be.264<comprehensive file >, also can be avi format.
User can also get out the hard drive or SD card, export and playback the video by professional software.
19-73
2.3. LOG SEARCH

In the log search interface, it records and displays all alarm events and login operation log. Enter the
"log query”, the interface will be shown as following:
Log Search interface instruction:

Calendar: the date with log will be marked on the calendar with green color.
Remark: There is no color classification in the “log mark”, and all are green ones.
20-73
Log search interface instruction:

Start time: the start time for searching log files
End time: the end time for searching log files
Log types: classification of log search, including the operation log and alarm log and locking log
Operation log search interface instruction
Log includes the following information:
Log time: the time when event is triggered
Log name: event content
Supports page up/page down and export all log files of the specified date.
Do not support link to video file.
Log search
Alarm type: It includes all alarms, IO alarm , panic alarm and over speed alarm.
21-73
Log time: the time when event is triggered

Supports page up/page down and export all log files of the specified date.
Supports link to video file, click on button to playback video files
Lock log search

Log time: the time of when event triggered.
Log will be recorded according to channel number, each channel will have a lock log file.
Support page up and page down.
Can’t export all log files of the specified date.
Can link to video file, click on button to playback video files.

Unlock: Select log, and unlock it. Then the alarm log of lock will be cleared.
Remark:
When lock the video file, system will record alarm log and lock log. The locked video file can only be
unlocked from alarm log.
2.4. SYSTEM STATUS

User can login the interface with no access restrictions.
 System- Version information
 System- Modules
22-73
 System-Server status
 System - Environment
23-73
 System-Storage:
2.5. BASIC SETUP

Click setup button and enter the following interfaces:
2.5.1. REGISTER INFOMATION (SETUP VEHICLE INFORMATION)
 Register information-Device info:
24-73
Device ID: Currently, it is not useful.

 Register information- Vehicle info
Vehicle Number：When connected with PAD, the vehicle number is needed.

Vehicle plate：Input manually.
Line number：Input manually.
 Register information—Driver info:
25-73
Driver number: Input manually.

Driver name: Input manually.
2.5.2. TIME SETUP
 Time setup-General
Date format: Setup the date format of device
Time format: 24 hours or 12 hours
Time zone: Range from -12th district ~ +13th district
 Time-Time Sync
26-73
Date/Time: Device time, from 2000-01-01 to 2036-12-31

Satellite: Synchronize time with GPS satellite. Once GPS signal changes to valid, device will
synchronize time
Center Server: synchronize time with center server
NTP sync: synchronize time with NTP server
Remark:
1) Synchronize time according to time zone
2) Multi-mode can be selected for time synchronization. If one works, the others take no affect.
Otherwise, it switches to another sync mode every 5 minutes.
 Time setup-DST
Enable: Select to enable

Offset: After enabling DST, adjust the hour manually
27-73
Mode: Setup DST according to week or date

Start: Time to start DST
End: Time to end DST
2.5.3. START UP
 Startup-ON/OFF
ON/OFF mode: 3 modes, including ignition, timer and ignition or timer.

Ignition: Input ignition delay time for shutdown delay function
Timer: When setup the start mode as Timer, please setup the start time and end time
Under this mode, MDVR’s start up or shut down time will not affect the ignition.
Remark:
If use setup as Ignition or Timer Mode, Ignition ON or Timer start time can trigger MDVR start up.
And only when Ignition off and Timer end time, MDVR will shut down.
 Start-Sleep
28-73
Sleep Mode: Currently, there is only no consumption standby mode available.

Low Volta protect: Enabling the low voltage shutdown protection mode selected.
Battery low voltage: Protect the vehicle battery. When consistently below the standard value, it will
countdown shutdown. As for a 12V vehicle, the default is 9V, while a 24V vehicle is 21V.
Voltage start up: low-voltage protection, when the battery voltage is consistently greater than the
standard value, it will automatically boot. As for a 12V vehicle, the default is 12.5V, while a 24V
vehicle is 24.5V.
Low volt upload: The low-voltage protection will be reported to the platform after it is ticked.
2.5.4. USER SETUP
In the basic settings, click user settings, enter the following interface, user can enter setting menu.
29-73
User name: The default ones are admin and user.

User Group: It is divided into administrator and ordinary user.
It supports delete user function. Select the user and click "Delete User" button. Please be noted that the
administrator cannot be deleted.
It supports add user function. Click "Add User" button, then enter the following interface.
Remark:
1) Only administrators can add users.
2) Users can add up to two.
3) User name cannot be empty, not the same with the existed user name while the user password can
be empty.
User name and password can be modified. Select a user, click the "Edit User" button, enter the following
interface:
Modify the user name and password to confirm the operation temporarily. There is no need to verify the
old password, Administrator user name cannot be modified.
2.5.5. NETWORK
In the basic settings, click Network Settings, enter the following interface, user can set network
parameters.
 Network - Local
30-73
Automatically obtain IP: Dynamic acquisition, DNS can also be statically configured to dynamically
obtain.
Use the following IP: Static IP, need to use a static DNS.
Remark:
Switch from static IP to automatically obtain IP mode, it can display dynamic IP, but the static IP
parameters will not be covered, to restore the last saved static IP after switching back.
 Network Settings - Ports:
WEB port No.: The default is 80.

 Network- WIFI
31-73
Enable: Select to enable WIFI

ESSID: Manually input the address of AP
Encryption: It supports NONE, WEP and WPA
Password: Manually input
Static IP: Select to use static IP, or MDVR will get dynamic IP
 Network-Communication:
Dialing wireless network, user needs to choose the module type and setup dialing parameters
When entering the dialing setup interface, it searches the wireless module type automatically. It shows
No Service when there is no module.
Network type: The default one is Mix, 2G/3G and 2G/3G/4G optional.
Dialing parameter：It includes access point, user name, password, data service number, and enter SIM
32-73
parameters provided by the manufacturer. The default is empty, the program comes with empty
arguments by dialing.
Certification：Supports PAP or CHAP.
Remark:
When there is SIM and normal 3G/4G signal, it will dial automatically.
 Network- Server
Center server: It supports 6 servers at most, and server 1 cannot be deleted manually.
ON: Enable the current server.
Protocol type: The default one is N9M.
Enable network: There is local, WIFI and module optional
Register server address: To run the registration server address.
Registration server port: To run the registration server port.
Media server address: To run the media server address.
Media server port: To run the media server port.
33-73
2.5.6. APPLICATION
 Application-FTP Client
FTP Enable: Enable FTP.

Server: To run FTP server address.
Port: To run FTP server port. (The default one is 21.)
User name/password: The accounts distributed by FTP server.
2.6. SURVEILLANCE
34-73
2.6.1. LIVE VIEW
 Live view-->Preview
Real-time Setting Interface:
Preview audio: Enable the audio when live view the video.
Image setup: Set the live-view parameters, including brightness, contrast, etc.
Startup Screen: Set the live-view screen, it can be single-screen or quad screen or nine screen
Channel: Set the channel when live-view
 Live view-Auto Loop:
Screen: Totally 32 screens can be added.

Mode: 1x1, 2x2, 3x3 optional.
Channel: Included channel number.
35-73
Duration: Duration for each screen.

Edit: Delete or Edit.
Add screen: Add polling screen
Auto polling: Enable the auto pulling
 Live view-Live OSD :
It displays the information on screen, such as time, speed, license plate, GPS...
The default is only the time, and the position cannot be set.
2.6.2. RECORD
 Record-->General
Video type: Default is PAL, NTSC optional
36-73
Overwrite: The earliest recording file will be deleted while the HDD or SD card is full to realize loop
recording.
Lock duration: Protect the record file to be deleted by fault, default is 7 days.
Pre-recording: Pre-record before the alarm happens. Default is 15min, 0-60min optional.
 Record-->Main Stream:
37-73
Channel: The total channel numbers of the device, including analog and digital channels.
Channel name: Change the name manually.
Enable: Enable the main stream record function
Resolution: The analog channel supports D1/HD1/CIF/WD1/WHD1/WCIF while the digital one supports
720P.
Frame Rate: Frame Rate of the recording.
Quality: Picture Quality of the recording.
Record mode: Ignition, Time, Event optional. Each channel can be set separately. The sub-stream and
mirror record are the same
Audio: Enable the audio. Note: Audio cannot be record separately
I frame: Enable to let the frame rate invalid, record file that does not have alarm is I frame only.
Alarm quality: The alarm image is different from the normal recording image.
Encode mode: It supports VBR and CBR modes.
 Record- Dual stream
38-73
Storage: The storage type for sub stream, internal SD and external SD optional.
Record mode: Mirror record, alarm back-up record and sub stream.
 Mirror record: Channel is selectable. Video resolution and frame rate are the same with main
stream.
 Alarm backup: Channel is selectable. The parameters are the same with main stream
 Sub stream: Channel is selectable. Recording parameters are configurable
Sub stream includes channel number, enable or not, audio, resolution, frame rate and image quality.
Sub stream channel: It is selectable according to recording mode.
 Record-->OSD
39-73
Embedded key information to video file for easily check when playback.
2.6.3. IPC SETUP
 IPC setup:
40-73
Channel: It includes the analog channels and IPC channels. Analog channel will not be shown if it
connects to network camera.
Enable: Enable to operate IPC.
IP and port: Display channel details after searching.
Setup: Search and edit IP camera recording parameters
Fast setup: Search all the IP cameras in LAN network, and auto assign IP address to IP camera.
IPC local address: To search network camera of local area network at Intranet. The default one is
10.100.100.1.
41-73
2.6.4. PTZ
Channel: It includes analog channels and IPC channels.

Enable: Enable PTZ.
Operate: It includes serial, N9M and ONVIF. It supports Pelco-D and Pelco-P PTZ protocols with serial
mode.
Address: It is valid with serial mode.
Test: It is to test PTZ is available or not. Click it to pop up PTZ control panel.
2.7. DATA COLLECTION
2.7.1. GENERAL
 General-->Sensor
42-73
Sensor number: The total alarm input numbers of MDVR.

Sensor name: IO sensor name, it can set manually. The sensor name of alarm setting interface will
update synchronously after setting.
OSD name: The information embedded to video image.
Copy: Copy the configuration and use it for other sensors.
 General-->Serial port:
RS232-1 and RS232-2, with the following features: three axis sensor, expansion, 485 bus and GPS
data.
RS485-1 and RS485-2, with the following features: PTZ, control panel, 485 bus and GPS data.
Baud Rate: 2400-115200, 9 classes optional.
Remarks:
43-73
For more information, please visit our website www.en.streamax.com
Model X3, X5 and X7 equip 4 serial ports, while model M1 and X1 equip only one RS232 port, but it
can realize the following features: expansion, control panel, 485 bus, GPS data, three axis sensor, PTZ
and integrated printer.
 General-->speed
Unit: KM/H and MPH selectable.

Source: GPS, pulse or both optional.
Calibration mode: No need to calibrate if setup as satellite mode.
2.7.2. SNAP SETTING
 Snap Setting-->Time snap
44-73
Start time: Start to snap.

End time: Stop snapping.
Setup: Delete and set.
Time snap: Enable to snap at the setting time.
Add: To add snap period, and it supports 8 pieces at most.
 Snap Setting--> Trigger snap
45-73
Trigger snap: It snaps when alarm is trigger.
2.7.3. ECO-DRIVING (It is still developing.)
46-73
2.8. ALARM
2.8.1. BASE
 Base-->Speed alarm
47-73
Name: The current name is over speed

Enable：Enable or disable, tick to enable
Alarm type: It includes the following types, important and general.
Trigger:
Over speed pre alarm difference: To set the pre alarm data. For example, if speed is 60 km/hour, and
over speed pre alarm difference is 10 km/hour, TSS sends over speed alarm broadcast and records
when it reaches 50 km/h.
Speed: It is the alarm speed.
Alarm duration: Alarm output duration
Linkage: When alarm triggered, link to other business operation.
48-73
Channel: Link to recording channel, optional.

Post recording: It means the recording duration after the alarm has been removed.
Lock: Enable to link recording lock when there is alarm.
3G network: When it is set as sensor trigger dial mode, it enables 3G network as it triggers alarm.
Linkage IO output: Enable to link alarm output when alarm is triggered.
Output delay time: It means the alarm output duration after alarm is removed.
Alarm upload: Enable to upload to platform.
Linkage screen: Enable to link the channel to show full image when there is alarm. ( Depends on the
MDVR model, display split 1/4/9 optional.)
PB alarm duration: It means the available alarm duration after urgent alarm is removed.
Alarm snap: Enable to link snap.
 Base- Panic alarm:
49-73
Name: The current name is panic.

Enable：Enable to panic button.
Alarm type: Important type and general type optional.
Trigger: Click any button to delay the time till it reaches the setting time to alarm.
Linkage: When alarm is triggered, link to business operation.
50-73

Linkage screen: Enable to link the channel to show full image when there is alarm. (Depends on the
51-73
 Base – IO alarm interface:
Name: From Sensor1 to Sensor8 (It includes all the alarm input numbers.)
Enable: Enable the sensor alarm.
Trigger: Low and high optional. It triggers alarm when it is low as default.
52-73

53-73
2.8.2. VIDEO
 Video-Video loss
Name: The default name is video loss.

Enable: Enable the video loss.
Trigger:
54-73
Video loss set: It includes all video channels that can be selected.
Set period: Set the checking period when video loss alarm is triggered.
55-73

56-73
2.8.3. ADVANCE
Name: The default name is ACC alarm.

Enable: Enable the ACC alarm.
Trigger: Set the threshold value of X/Y/Z.
57-73

X:0.0, Y:0.0, Z:0.0: The real time acceleration information.
2.9. MAINTENANCE
58-73
After login, click setup>Maintenance, and then enter into the page as follow.
2.9.1. CONFIGURATION
In the configuration page, user can export and import the configuration file.
Insert flash drive to export the configuration file to the root folder, the file name is ConfigFile
Insert flash drive to import configuration file into MDVR, and it will display the notice when import
successfully.
Remark:
It won’t import the register info and speed adaption info.
2.9.2. DATA EXPORT
User can export any file.

File type: GPS data file, vehicle info file, ACC info file, Can info file, Dial info file and Captured pic.
59-73
2.9.3. UPGRADE
In the page of upgrade, user can upgrade software.
Put the upgrade file in flash drive. Currently, device firmware, microcontrollers firmware,
CP4 firmware and IPC firmware can be put inside.
Insert flash drive and enter the upgrade interface, click software upgrade and it will indicate
that upgrade file is importing.
MDVR reboot up and enter into upgrade interface after importing successfully.
60-73
Remark:
1) Make sure don’t power off during upgrading.
2) Put the upgrade file into the folder “upgrade”, which is at the root directory if the USB drive
3) It support upgrade firmware, LOGO, MCU, and MCU for CP4.
4) Firmware and MCU will package in one file, and it will upgrade MCU first, and then firmware.
5) The name of the LOGO are: logo_update(10.12.15).jpg and logo_cvbs(11.12.15).jpg
6) Please don’t put many files in the same folder when it is upgrading, otherwise, it will
upgrade one randomly.
2.9.4. STORAGE
In this page, user can format all the storage.
Storage type: HDD, SD card (Internal), SD card (External), USB drive
Free/Total
 Not exist: Didn’t find the HDD (not install or broken)
 Unformatted: Means the HDD has been detected, but unformatted.(New HDD)
 Capacity info: Display the correct info means HDD working fine
Format:
Click format and it will refresh the current formatted volume information after formatting successfully.
It can record after formatting successfully and no need to reboot up.
61-73
2.9.5. DEFAULT
In this page, you can click the default button to reset the parameters to factory settings.
Click reset to restore the original data.

Remark:
For, language, MAC address, register info, CMS server info, speed adaption parameter will not change
during default settings.
3. WEB MANAGEMENT
3.1. LOGIN INTERFACE

1) Connect MDVR into local area network, set relevant information to make sure the computer can
visit the MDVR.
2) Open browser and input http:// IP address of MDVR. It will go to the WEB login interface
of MDVR. And the default IP address is 192.168.1.100
3) Interface will pop up a window to install N9M activex, click install.
4) Refresh the web page, enter default user name admin/admin to log in.
62-73
3.2. MAIN INTERFACE
63-73
Icons: quad, 9-split, preview, next page, sound, capture and video parameters.
Stream switch: main stream, sub-stream and network transmission sub stream.
Log out: log out and come to the log in interface
3.3. PLAYBACK
64-73
If the date is marked as color green, it means there is recording.
65-73
Recording playback window: Video window, play time-line, play control button, window switch...
Record list: It displays all the record. Click backup download video file to local computer hard disk.
3.4. MAINTENANCE
66-73
3.4.1. BASIC INFORMATION
Basic information: It contains the current state & history state of channel video and storage.
3.4.2. DEVICE MODULE
Device module: It is about the current state of module, WIFI module and satellite location module.
67-73
3.4.3. STORAGE DEVICE
Storage device: There are the volume information & format operation of storage (hard disk/flash
drive/SD card), and the path of snap & record backup.
68-73
3.4.4. VERSION INFORMATION
Version information: There are device type, name, firmware version, MCU version, CP3/4 version,
upgrade, configuration file export and configuration file import.
 Log
Log: There is Log type (operation log, alarm log and locked log), operation type (IO alarm, panel alarm,
speed alarm, video loss and ACC alarm) date, and log export.
3.5. CONFIGURATION
69-73
The parameter setting is the same as the local setting. User can view the operation at the local setting.
70-73
4.STORAGE CAPACITY CALCULATION

1) Image Quality & Streams
Resolution Image 1 2 3 4 5 6 7 8
quality
720P 6144 4800 4128 3456 2784 2112 1440 768
WD1 2662 1997 1599 1331 1170 1040 936 832
WHD1 1664 1248 998 832 728 650 585 520
Stream
WCIF 1040 780 624 520 455 405 364 325
Kbps
D1 2048 1536 1230 1024 900 800 720 640
HD1 1280 960 768 640 560 500 450 400
CIF 800 600 480 400 350 312 280 250
2) Record File Size Calculation
Rec. file size for each channel is:
Recording time (s) x Stream (Kbps) / 8 / 1024 = File Size (MB)
e.g. The file size of the Image 1 with D1 resolution within 1 hour:
3600 x 2048 Kbps / 8 / 1024 = 900 MB
3) Image Quality & Resolution

Image
Resolution 1 2 3 4 5 6 7 8
quality
720P 2700 2109 1814 1518 1223 928 632 337
WD1 1170 878 702 585 514 456 411 365
WHD1 731 549 438 365 320 285 257 229
Record
WCIF 456 343 274 229 199 178 160 143
(MB)
D1 900 675 540 450 395 351 316 281
HD1 562 422 337 281 246 219 198 176
CIF 351 264 211 176 153 137 123 110
71-73
5.FREQUENTLY ASKED QUESTIONS

1) The system can’t start?
Usually this problem results from the incorrect power connection. Please follow below steps to
check the power connection:
1. Check the input power, whether the power wire is connected correctly, whether the ground wire is
connected back to the battery, and whether the fuse on the power wire is in good condition.
2. Check whether the ACC signal wire input to the power is with voltage higher than 7 V.
3. Check whether the device key is closed.
2) The MDVR restarts uninterruptedly?
Please follow below steps to check it:
1. Check whether the voltage of MDVR is insufficient. If the voltage is less than the start-up voltage of
the device, the device would always restart.
2. The problem in hard disk/SD card may cause the failure to start. Take off the storage part and check
whether it is broken down.
3) The device can’t record?
Usually this problem results from the storage disk or camera. Please follow below steps to check it:
1. Check whether the storage disk is installed, whether it is in good contact, and whether the disk can
be read normally in computer.
2. Check whether the storage disk is formatted. The storage disk should be formatted before normally
storing record files.
3. Check whether there is video signal input into the device from camera, and whether there is
video/image on the screen.
4) There is no voice in record file?
1. Check whether there is an external pickup, or whether the camera features with the function of
audio collection.
2. Access to Video Channel Settings, check if Audio is set on.
3. There must be video input into the channel for recording and it must record normally.
5) The GPS works abnormally?
1. Check whether the GPS antenna is installed correctly. There is a silk print logo on the GPS antenna
holder behind the host device.
2. Check whether the antenna receiver is sheltered. It should not be covered by any stuff, which may
cause it not to receive signals.
3. Environmental influence such as tree shades, being inside tunnel, driving near tall building or
elevated roads, thunderstorms or other weather influence, etc. can also cause signal loss or
receiving wrong signals.
6) The device can’t shutdown in ignition switch mode?
1. Check if the ACC line connection mode is correct; and check whether there is voltage on ACC
yellow line when the key is turned off.
2. If the device has been set with schedule recording, it can’t shutdown if it is still during recording time
72-73
of the task table.

7) Which IP waterproof level does Streamax device support?
Currently, X7 and X5-E0804 support waterproof IP 54.
8) How to install the WIFI antenna?
The antenna must be installed on unobstructed place of the roof, and be fixed with glue.
9) The device cannot be shut down when in ignition ON/OFF mode.
Check if the ACC signal wiring is correct and if there is voltage for ACC signal line after the key is
turned off .
If you have set timing recording, and at the current time it is still in task recording, the device may be
impossible to be shut down.
10) GPS anomaly.
Check if the GPS antenna is properly installed. There is silkscreen GPS identification on the GPS
antenna pedestal on the back of the MDVR device. Check if the antenna connector is blocked and
make sure the antenna connector not be covered by other things.
Trees block, being inside the tunnel, driving near tall buildings or viaduct, thunderstorms and other
environmental effects may also cause to receive no GPS signal or error signal.
11) No voice in video files.
See if there is an external microphone, or if the camera cannot capture audio;
Enter into the video channel settings, then check if the audio is open;
Ensure video input and normal recording, on which the audio recording channels must be based.
12) The device doesn’t record.
Make sure the storage part is installed and of fine contact, the data can be read on PC, and the
storage device is not formatted.
Check if there are video signal input to the main device, and whether there are video images in the
channel pictures.
13) Why has the MDVR device always been in a state of restart?
Check whether the MDVR device voltage is insufficient. If the device voltage does not reach the
start voltage, the device will restart.
Hard disk or SD card may cause the MDVR device unable to start. You need to remove the storage
device and then boot up to verify whether it is caused by the storage device.
14) Why the MDVR device cannot start?
Check the device input power to see if the power wiring is correct, if there is ground wire connected
back to the battery, and if the fuse of the power wire is n good condition;
Check whether there is voltage(more than 7V) on power input ACC signal wire;
Check whether the hard disk key is turned off.
15) What is the log in user name and password for new device?
The default user name and password are both “admin”. The device password can be set as empty.
16) How to update the firmware?
Change the previous file folder name “dvrupgrade” to “upgrade”. Change the file name
FWX15-0401-05-01-V01V01V01V491087 to RMMDVR_X5_III_T2014111005_convert
17) In the ON/OFF of basic settings, the low voltage protection is 8V, why?
After testing, when the battery is lower than 8V, the voltage will lower down quickly. Therefore the
lowest voltage is set to be 8V. When it is lower than 8V, the MDVR device will recognize it as
external power-off and then enter into shutdown state.
73-73

Manual XMR401HDS

Uploaded by

Copyright:

Available Formats

Manual XMR401HDS

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manual XMR401HDS

Uploaded by

Copyright:

Available Formats

User manual for XMR401HDS

Mobile Digital Video Recorder

Guarantee & Warnings

Image Quality 1-8 levels adjustable (1 is the best)

1.3. SYSTEM DIAGRAM

1.4. EXTERNAL INTERFACE

Serial No. Description

Serial No. Print Description

1.5. HARD DISK INSTALLATION

1.6. SIM CARD INSTALLATION

1.7. DEFINITION AND PICTURES OF EXTERNAL CABLES

Alarm and Serial Cables A/V OUT Cable

2.1. LOGIN INTERFACE

Default password and permission table is as follows:

The password input Instruction:

2.2. RECORD SEARCH:

In the calendar, the color below the dates means:

2.3. LOG SEARCH

Log Search interface instruction:

Log search interface instruction:

Log time: the time when event is triggered

Supports link to video file, click on button to playback video files

Lock log search

Can link to video file, click on button to playback video files.

2.4. SYSTEM STATUS

2.5. BASIC SETUP

2.5.1. REGISTER INFOMATION (SETUP VEHICLE INFORMATION)

 Register information-Device info:

Device ID: Currently, it is not useful.

Vehicle Number：When connected with PAD, the vehicle number is needed.

Driver number: Input manually.

2.5.2. TIME SETUP

Date/Time: Device time, from 2000-01-01 to 2036-12-31

Enable: Select to enable

Mode: Setup DST according to week or date

ON/OFF mode: 3 modes, including ignition, timer and ignition or timer.

Sleep Mode: Currently, there is only no consumption standby mode available.

2.5.4. USER SETUP

User name: The default ones are admin and user.

WEB port No.: The default is 80.

Enable: Select to enable WIFI

FTP Enable: Enable FTP.

2.6.1. LIVE VIEW

Screen: Totally 32 screens can be added.

Duration: Duration for each screen.

Video type: Default is PAL, NTSC optional

2.6.3. IPC SETUP

Channel: It includes analog channels and IPC channels.

2.7. DATA COLLECTION

Sensor number: The total alarm input numbers of MDVR.

Unit: KM/H and MPH selectable.

2.7.2. SNAP SETTING

 Snap Setting-->Time snap

Start time: Start to snap.

Trigger snap: It snaps when alarm is trigger.

2.7.3. ECO-DRIVING (It is still developing.)

Name: The current name is over speed

Channel: Link to recording channel, optional.

 Base- Panic alarm:

Name: The current name is panic.