STEVAL-ISA102V2: 80 W High Performance Transition Mode PFC Evaluation Board Based On L6562A
STEVAL-ISA102V2: 80 W High Performance Transition Mode PFC Evaluation Board Based On L6562A
Description
The L6562A is a current-mode PFC controller
operating in transition mode (TM). With the same
pinout as its L6562 predecessor, the L6562A
offers improved performance mainly in terms of
efficiency and noise immunity.
The STEVAL-ISA102V2 implements an 80 W,
wide-range mains input and a PFC pre-
conditioner suitable for lighting, adapters,
consumer smps, etc.
Features
Line voltage range: 88 to 265 VAC
Minimum line frequency (fL): 47 Hz
Regulated output voltage: 400 V
Rated output power: 80 W
Maximum 2fL output voltage ripple: 10 V pk-
pk
Hold-up time: 20 ms (VDROP after hold-up
time: 300 V)
Minimum switching frequency: 35 kHz
Minimum estimated efficiency: 92% (VIN =
90 VAC, POUT = 80 W)
Maximum ambient temperature: 50 °C
PCB type and size: single-side, 35 μm,
CEM-1, 108 x 57 mm
RoHS compliant
2/4
Schematic diagram
Vo=400V
D1 NTC
STTH1L06 2.5 Ω Po=80W
T1
R4 R5 D8 C5 R14
270 kΩ 270 kΩ 1N4148 10 nF 100Ω R11
1M Ω
D2 R50 - 22 kΩ
R1 R12
1 MΩ 1N5248B
R6 1M Ω
C3 - 2200 nF
Schematic diagram
47 kΩ
C1
P1 C23
0.22
0 22 µF
F ZCD COMP 150 nF INV
F1 + W08
630V C6
4A/250V R2 VCC
1 MΩ 8 5 2 1 R7 47 µF
33 Ω 450V
MULT 3 GD Q1
Vac - L6562A 7
STF7N60M2
88V
DocID029799 Rev 1
to 6 4 R8
264V 47k Ω
C2 GND CS R15
10nF C29
R3 C4 SHORTED
22 µF R9 R10
15 kΩ 100 nF R13 R13B
25V 0.68 Ω 0.68 Ω 15 kΩ 82 kΩ
0.25W 0.25W
Figure 1: STEVAL-ISA102V2 circuit schematic
GSPG2809161015SG
STEVAL-ISA102V2
STEVAL-ISA102V2 Revision history
2 Revision history
Table 1: Document revision history
Date Version Changes
29-Sep-2016 1 Initial release.
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST
products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the
design of Purchasers’ products.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.