Introduction 1

Installation notes 2
Installation/License key/
Uninstallation 3

Tips for use 4

Support Request 5

Readme

02/2020
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.

DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION
indicates that minor personal injury can result if proper precautions are not taken.

NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:

WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this
publication is reviewed regularly and any necessary corrections are included in subsequent editions.

Siemens AG Copyright © Siemens AG 2019.

Smart Infrastructure Ⓟ 02/2020 Subject to change All rights reserved
Control Products
Werner-von-Siemens-Str. 48-50
92224 AMBERG
GERMANY
Table of contents

1 Introduction...................................................................................................................................................5
1.1 Installation and use ..................................................................................................................5
1.2 Security information .................................................................................................................5
1.3 Information on data protection .................................................................................................5
2 Installation notes...........................................................................................................................................7
2.1 Scope of supply........................................................................................................................7
2.2 Hardware requirements............................................................................................................8
2.3 Software requirements .............................................................................................................8
3 Installation/License key/Uninstallation........................................................................................................11
3.1 Installation ..............................................................................................................................11
3.2 License key ............................................................................................................................12
3.3 Uninstallation..........................................................................................................................14
3.4 Advanced installation notes ...................................................................................................14
3.4.1 Using a wheel mouse.............................................................................................................14
3.4.2 Notes concerning the use of communications cards in PCs/programming devices...............14
3.4.3 S7 Teleservice .......................................................................................................................16
4 Tips for use.................................................................................................................................................17
4.1 Upgrading a SIMOCODE pro project .....................................................................................17
4.2 Release notes ........................................................................................................................17
4.3 Information on the documentation..........................................................................................17
5 Support Request.........................................................................................................................................19
Index...........................................................................................................................................................21

Readme, 02/2020 3
Table of contents

4 Readme, 02/2020
Introduction 1
1.1 Installation and use
These notes take precedence over statements made in other documents.
Read the notes carefully because they contain important information for installation and use of
the software SIMOCODE ES V16 for you.

1.2 Security information

Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected
to an enterprise network or the internet if and to the extent such a connection is necessary and
only when appropriate security measures (e.g. firewalls and/or network segmentation) are in
place.
For additional information on industrial security measures that may be implemented, please
visit
https://www.siemens.com/industrialsecurity.
Siemens’ products and solutions undergo continuous development to make them more secure.
Siemens strongly recommends that product updates are applied as soon as they are available
and that the latest product versions are used. Use of product versions that are no longer
supported, and failure to apply the latest updates may increase customer’s exposure to cyber
threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under
https://www.siemens.com/industrialsecurity.

1.3 Information on data protection

Siemens observes standard data protection principles, in particular the principle of privacy by
design.
For SIMOCODE ES this means:
SIMOCODE ES does not process or store any personal data, only technical function data (e.g.
time stamps). If you link this data with other data (e.g. shift schedules) or store personal data
on the same storage medium (e.g. hard disk), and thus establish a link to a person or persons,
then you are responsible for ensuring compliance with the relevant data protection regulations.

Readme, 02/2020 5
Introduction
1.3 Information on data protection

6 Readme, 02/2020
Installation notes 2
The installation notes contain important information that you require to install
the SIMOCODE ES V16 software.
Read these notes before you start installation.

2.1 Scope of supply

This version is provided in six languages and runs under any operating system listed in
section Software requirements (Page 8).

Package Article number Scope

Professional
Floating license 3ZS1 322-6CC14-0YA5 ● 1 setup DVD
● 1 license key on USB flash drive
● 1 certificate of license
License download 3ZS1 322-6CE14-0YB5 ● 1 license key per download
● 1 certificate of license by download
Software update service 3ZS1 322-6CC00-0YL5 Software update service for 1 year with
automatic extension.
Requires the current software version.
Basic (free of charge)
Software download (Siemens Indus‐ Software download (https:// 1 software download; basic functional
try Online Support) support.industry.siemens.com/cs/ww/e scope and Premium trial license inclu‐
n/view/109771523) ded

Note
License key
● The existing standard and premium licenses will be integrated into Professional as of
version V16.
● Existing standard licenses can be used like Professional in version V16.
● Earlier versions can still be used.

Note
Combo licenses
All available license keys are combo licenses, which can also be used with SIMOCODE ES
2007.

Readme, 02/2020 7
Installation notes
2.3 Software requirements

2.2 Hardware requirements

SIMOCODE ES V16 supports all common Windows standard PCs and SIMATIC programming
devices.
Working with SIMOCODE ES V16 sets minimum requirements for the hardware. In order to
work efficiently with SIMOCODE ES V16, use the recommended values.

Minimum hardware requirements:

Hardware Requirements
Processor Intel ® Core™ i3-6100U, 2.30 GHz
RAM 8 GB
Hard disk S-ATA with at least 8 GB of free storage space
Screen resolution 1024 x 768

Recommended PC hardware:

Hardware Requirements
Computer As of SIMATIC FIELD PG M5 Advanced (or comparable PC)
Processor Intel ® Core™ i5-6440EQ (up to 3.4 GHz)
RAM 16 GB or more (32 GB for large projects)
Hard disk SSD with at least 50 GB of free storage space
Monitor 15.6" full HD display (1920 x 1080 or higher)

Note
SIEMENS communications processor required
To use SIMOCODE ES V16 with PROFIBUS (Professional version only), you also need a
SIEMENS communications processor for a PROFIBUS network.

2.3 Software requirements

Runtime environment

Operating systems
SIMOCODE ES V16 is released for the following operating systems:

Windows 7 (64 bit)

● Windows 7 Professional SP1
● Windows 7 Enterprise SP1
● Windows 7 Ultimate SP1

8 Readme, 02/2020
 Installation notes
2.3 Software requirements

Windows 10 (64 bit)

● Windows 10 Professional Version 1809
● Windows 10 Professional Version 1903
● Windows 10 Enterprise version 1809
● Windows 10 Enterprise version 1903
● Windows 10 Enterprise 2015 LTSB
● Windows 10 (IoT) Enterprise 2016 LTSB
● Windows 10 Enterprise 2019 LTSC

Windows Server (64 bit)

● Windows Server 2012 R2 StdE (full installation)
● Windows Server 2016 Standard (full installation)
● Windows Server 2019 Standard (full installation)

Note
End of the extended support for Windows 7
Please note the end of the extended support for Windows 7. Microsoft will no longer provide
security updates or support for PCs running Windows 7 after the end of extended support for
Windows 7. However, you can still install the software.

Supported virtualization software:

● VMware vSphere Hypervisor (ESXi) 6.5 (or higher)
● VMware Workstation 15.0.2 (or higher)
● VMware Player 15.0.2 (or higher)
● Microsoft Hyper-V Server 2016 (or higher)

NOTICE
Encrypting File System (EFS)
Never encrypt the installation folder (e.g. C:\Program Files\Siemens) with the EFS.
Otherwise, important services such as the Automation License Manager will no longer
function.

Readme, 02/2020 9
Installation notes
2.3 Software requirements

Supported security programs

The following security programs are compatible with SIMOCODE ES V16:
● Virus scanners:
– Symantec Endpoint Protection 14.0
– McAfee Endpoint Security (ENS) 10.5
– Trend Micro Office Scan 12.0
– Kaspersky Endpoint Security 11.1
– Windows Defender (as part of the Windows operating system)
– Qihoo 360 "Safe Guard 11.5" + "Virus Scanner"

Note
Ensure that your virus scanner and its databases are always up-to-date.
The most recent update of the virus patterns was on February 7, 2020.

● Encryption software:
– Microsoft Bitlocker
● Host-based Intrusion Detection System:
– McAfee Application Control 8.0

User rights
Restricted user rights are sufficient for working with SIMOCODE ES V16.
However, you must have administration rights to install SIMOCODE ES V16. All users working
on this PC with SIMOCODE ES V16 require authorization to write to the installation folder of TIA
Portal V16.

Compatibility with STEP 7

You need to install STEP7 V16 to integrate SIMOCODE ES V16 in STEP 7.

Online documentation
For information about the immediate operating and functional context, refer to the standard
Windows Help. For more details about the structure of the documentation, see
section Information on the documentation (Page 17).

10 Readme, 02/2020
Installation/License key/Uninstallation 3
3.1 Installation
Installation of SIMOCODE ES V16

Note
Side-by-side installation of SIMOCODE ES V15.1 and SIMOCODE ES V16
A parallel installation of SIMOCODE ES V15.1 and SIMOCODE ES V16 is possible on your
computer.

Close all applications (Microsoft Word, etc.) and the "Control Panel" window before starting the
setup program. After installing SIMOCODE ES V16, you might have to restart Windows in order
to activate all system variables.
Insert the SIMOCODE ES V16 DVD into the drive. A menu-prompted setup program guides
you through the installation procedure for SIMOCODE ES V16. The installation program starts
automatically when you insert the SIMOCODE ES V16 DVD. If you have deactivated this
function on your computer, you can start setup in the MS Windows Explorer by double-clicking
the "SETUP.EXE" program on the DVD. The setup guides you step by step through the
installation procedure.
When setup is complete and you have (if necessary) restarted your computer, you can start
SIMOCODE ES V16 by double-clicking on the desktop icon "TIA Portal V16" or, for example,
under Microsoft Windows via the entry under "Start → SIEMENS Automation → TIA Portal V16."

NOTICE
TIA Portal V16 registers itself in Microsoft Windows system files
You must not move or rename any TIA Portal V16 files or folders using Microsoft Windows
tools such as Explorer, nor should you modify any TIA Portal V16 data in the Windows registry.
Making such modifications can affect program execution.

Readme, 02/2020 11
Installation/License key/Uninstallation
3.2 License key

3.2 License key

Before you can start working with SIMOCODE ES V16, you must transfer the license key (user
authorization) to the computer. There are two ways of doing this:
● During installation of SIMOCODE ES V16, you will receive a prompt from the setup program
if your computer does not have a suitable license key. You can then either have the setup
program install the license key or you can install the license at a later time using the
"Automation License Manager" program.
● If the license key cannot be installed during setup, continue the setup program without
installing the license key. Then restart the computer and install the license key with the Start
menu item "Siemens Automation\Automation License Manager".

Note
License key
The license key of previous versions can be used for version V16.

Automation License Manager

NOTICE
Automation License Manager as a requirement for operating SIMOCODE ES V16
To operate SIMOCODE ES V16, you must make sure that the Automation License Manager
is installed.

NOTICE
Installation of the Automation License Manager
The Automation License Manager prevents the authorizations and license keys from being
installed on invalid drives or media, such as RAM drives, diskettes or compressed drives (e.g.
DBLSPACE).
If the hard disk of a device with a removable drive bay is registered as "Exchangeable memory
medium" and not as "hard disk", it will be treated like a DVD and cannot be used for installation
of license keys.
In the case of compressed drives, you can install on the associated host drive.
Be sure to observe the notes on the Automation License Manager in the Readme file on the
SIMOCODE ES V16 installation DVD under "InstData\ALM32_64\Media\ALM64\".

12 Readme, 02/2020
 Installation/License key/Uninstallation
3.2 License key

Notes regarding fault-free operation of the license key

NOTICE
The USB flash drive must not be write-protected.
Without write-protection of the USB flash drive, there is a danger that viruses could be
transferred from the hard disk to the USB flash drive.
You should therefore run a virus check on your programming device / PC before you install/
uninstall a license key.

NOTICE
Using an optimizing program
If you use an optimizing program that enables you to move fixed blocks of memory, only use
this option once you have transferred the license key from the hard disk back to the USB flash
drive.

NOTICE
Cluster on the target drive
The license key will create a cluster with a special identification on the target drive. Some
inspection programs will identify this cluster as "defective."
Do not attempt to restore it.

NOTICE
Transferring the license key to the USB flash drive
Remember to copy the license key to the USB flash drive before formatting, compressing or
restoring your hard disk or before installing a new operating system.

NOTICE
Risk of losing a license key
If a backup copy of your hard disk contains copies of license keys, there is a risk that these
copies can overwrite the valid installed license keys and thus destroy them when you restore
your backup data to the hard disk.
To prevent a valid license key from being overwritten by a backup copy, you are strongly
advised to remove all license keys or exclude them from the backup process before you start
with the backup.

Trial license
If no valid license key is installed for SIMOCODE ES V16, a trial license key is used. This is
supplied and installed by default together with SIMOCODE ES V16. However,
SIMOCODE ES V16 can only be used for 21 days with this license key. When
SIMOCODE ES V16 is started for the first time without a valid license key, activation of the
trial license key is offered.

Readme, 02/2020 13
Installation/License key/Uninstallation
3.4 Advanced installation notes

3.3 Uninstallation

NOTICE
Uninstallling SIMOCODE ES V16
Uninstallation must be performed in the usual MS Windows way.
Uninstall your software package (e.g. "Siemens Totally Integrated Automation Portal V16") via
the Windows application "Software" (e.g. under MS Windows via "Control Panel → Programs
and Features").

3.4 Advanced installation notes

3.4.1 Using a wheel mouse

NOTICE
Manufacturer's driver
If you use a wheel mouse, make sure that the drivers supplied by the wheel mouse
manufacturer have been installed. If they are not, you can find that the functions of the wheel
mouse wheel are not always supported by SIMOCODE ES V16.

3.4.2 Notes concerning the use of communications cards in PCs/programming devices

CP5611 (SIMATIC NET PROFIBUS interface via PCI bus)
You require a PC or a programming device with PCI bus to use the CP5611 card. You can then
address SIMATIC stations via MPI or PROFIBUS (9.6 Kbps to 12 Mbps).
If you install SIMOCODE ES V16 after the CP has been inserted in the computer, the plug-and-
play mechanism enters the CP5611 in the Device Manager of the Control Panel\System in
"Other Devices". Therefore the CP is sometimes not recognized when installing
SIMOCODE ES V16.
In such cases, remove the CP5611 in the Device Manager after installing SIMOCODE ES V16
and reboot your computer.
Observe the notes in the online help under "Setting the PG/PC interface."
CP5512 (SIMATIC NET PROFIBUS interface via PC card)
A PC or a programming device with a PC card slot is required to use the CP 5512. You can then
address SIMATIC stations via MPI or PROFIBUS (9.6 Kbps to 12 Mbps).
CP5711 (SIMATIC NET PROFIBUS interface via USB 2.0)

14 Readme, 02/2020
 Installation/License key/Uninstallation
3.4 Advanced installation notes

A PC or a programming device with a USB slot is required to use the CP5711. You can then
address SIMATIC stations via MPI or PROFIBUS (9.6 Kbps to 12 Mbps).

Programming device/PC settings

To start up the plug-and-play-enabled modules (e.g. CP5512, CP5611 or CP5711), the
following procedure is recommended under MS Windows:
1. Install SIMOCODE ES V16.
2. Close MS Windows, switch off the PC and insert the card.
Note
The CP5512 can also be plugged in during operation.

3. The communications card is automatically installed after switching on again (or plugging in
the CP5512).
4. The hardware assistant appears under MS Windows. In the first dialog box that opens,
select the option "No, not this time." Confirm all further dialog boxes (not with Cancel!).
5. Start TIA Portal V16 in the project view, and in the project navigation open folder "Online
Access."
6. Right-click the interface adapter whose settings you would like to change. Select
"Properties" in the shortcut menu. In this dialog box, change the properties of module.

Note
Observe the notes in the online help under "Setting the PG/PC interface."

Note
Installing the communications drivers
When SIMOCODE ES V16 is installed on programming devices, the communication drivers
are installed automatically and the default settings are accepted.

Interrupt and address under MS Windows 7

The settings for interrupt and address cannot be changed in MS Windows 7.
The set values can be viewed as follows: For example, under "Start → Settings → Control
Panel → Administrative Tools" open Computer Management and then "System." Under "Device
Manager," you can view the values of the individual modules and under "System
Information → Hardware Resources," the overview of the assigned resources.

Note
Reserving an interrupt and address range for PCI components
In the BIOS of the PC, under certain conditions a specific interrupt and address range can be
reserved for PCI components.
Consult your PC or BIOS vendor.

Readme, 02/2020 15
Installation/License key/Uninstallation
3.4 Advanced installation notes

Operating networks exclusively with passive nodes (slaves)

Before you start working with your programming device/PC on a network to which only slaves
(passive nodes) are currently connected, you must activate the option "Only master on the
bus". Otherwise, your programming device/PC will remain inactive.
To do this, proceed as follows:
1. In the project navigation in the "Online Access" folder, right-click on the programming device/
PC interface and select command "Properties" from the shortcut menu.
2. Display the properties of the module parameters used.
3. Activate the option "Only master on the bus."
4. Close the dialog box again.
Once you have finished working on this network, you should deactivate the option. In this way,
you will protect the network from possible interruptions caused by plugging in the PROFIBUS/
MPI cable while the interface on your programming device/PC is active.

3.4.3 S7 Teleservice
For SIMOCODE ES V16, the "S7-Teleservice" function is only available via MPI when used
with TS adapter I or II.

16 Readme, 02/2020
Tips for use 4
4.1 Upgrading a SIMOCODE pro project
If you open a project created in a previous version of SIMOCODE ES it will be upgraded with
user guidance.
You must then
● close any previously opened editors (device configuration, parameters, commissioning)
● update the module description for every module. Updating the module description means
upgrading devices to the latest version while keeping the current parameterization and
device configuration.
– In the device configuration, select the module for which you would like to change the
module description
– In the Inspector window select the "General" tab
– Click on the button "Update module description"
You will also find general information about this topic in the Online Help in the information
system under "Editing devices and networks → Configuring devices and
networks → Configuring devices → Update module description". See Information on the
documentation (Page 17).

4.2 Release notes

The information contained in the release notes is more up to date than the information in the
online help and therefore takes precedence over it.

4.3 Information on the documentation

The SIMOCODE ES V16 documentation is available via the online help. You can open the
online help from the menu item "Help → Show Help." The "information system" contains all the
essential information that you need for working with the SIMOCODE ES V16 software.

Readme, 02/2020 17
Tips for use
4.3 Information on the documentation

18 Readme, 02/2020
Support Request 5
Using the Support Request form in Online Support you can send your query directly to our
Technical Support. After describing your query in a few guided steps, you will immediately be
provided with possible suggestions for solving the problem.

Support Request: https://support.industry.siemens.com/my/ww/documents/requests (https://

support.industry.siemens.com/My/ww/en/requests)

Readme, 02/2020 19
Support Request

20 Readme, 02/2020
Index

A N
Automation License Manager, 12 Notes regarding fault-free operation of the license
key, 13

B
Basic, 7
O
Online documentation, 10
Online help, 17
C Operating networks exclusively with passive nodes
(slaves), 16
Combo licenses, 7
Operating systems, 8
Communication drivers, 15
CP5512 (SIMATIC NET PROFIBUS interface via PC
card), 14
CP5611 (SIMATIC NET PROFIBUS interface via PCI
P
bus), 14 Professional, 7
CP5711 (SIMATIC NET PROFIBUS interface via Programming device/PC settings, 15
USB 2.0), 14

R
E Reserving an interrupt and address range for PCI
Encrypting File System (EFS), 9 components, 15

H S
Hardware requirements, 8 S7 Teleservice, 16
Security programs, 10
Side-by-side installation, 11
I SIEMENS communications processor, 8
Support Request, 19
Information system, 17
Installation of SIMOCODE ES V16, 11
Installation of the Automation License Manager, 12
Interrupt and address under MS Windows 7, 15
T
Trial license, 13

L
License key, 7, 12
U
Uninstallling SIMOCODE ES V16, 14
Updating the module description, 17
M Upgrading a SIMOCODE pro project., 17
User rights, 10
Manufacturer's driver, 14

Readme, 02/2020 21
Index

22 Readme, 02/2020