CX H81-M1 Series

Referencia de diseño de Motherboard

Conectores internos

1 FRONT PANEL 2 SPDIF_OUT 3 INTERNAL PARAELLE

AUDIO CONNECTOR CONNECTOR PORT CONNECTOR

Contenidos

F_AUDIO_DET#

LINE*_RTU
MIC*_RTU

SLCT
PE
BUSY
ACK#
SPD7
SPD6
SPD5
SPD4
SPD3
SPD2
SPD2
SPD1
SPD0
STB#
• Especificaciones • Selectores de función

SPDIF Out
GND

Ground

+5V
• Diseño de Motherboard • Conectores internos

NC
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
SLIN#
PINIT#
ERROR#
AFD#
MIC*_L
MIC*_R
LINE*_R
GND
LINE*_L
• Conectores del panel trasero
F_AUDIO SPDIF_OUT PARAELLE

Especificaciones Diseño de Motherboard 4 INTERNAL SERIAL 5 TPM (Trusted Platform 6 INTRUDER

PORT CONNECTOR Module) CONNECTOR
Intel socket 1150 ATX CPU power
CPU Socket connector CPU fan connector

CK_33M_TPM
DDSR*#
DDTR*#
TDP: 95W

CCTS*#
RRXD*
13 12

LFRAME#
LDREQ0#
+3P3VSB
Chipset Intel H81

PLTRST#
LPCPD#

+3P3V
LAD0

LAD3
Dual-channel, 2 Slots, Non-ECC, Unbuffered, 240 pin DDR3, Max. up to 16GB for all.

GND

INTRUDER#
Memory PS/2 KB/MS ports
Types: 1066/PC3-8500, 1333/PC3-10600, 1600/PC3-12800

Ground
11
Graphics Integrated Graphics ROM Recovery

DDCD*#
TTXD*
Ground
RRTS*#
RRI*#
1 x PCI Express slot (x16)

NC
SMB_CLK_MAIN
GND
SERIRQ
NC
GND
LAD1
LAD2

GND
BUZZER
Expansion slots 1 x PCI Express slot (x1) Serial Port/ Memory
2 x PCI slots Display (DVI) port sockets

Audio Realtek ALC662

LAN Gigabit : Realtek RTL8111G
COM TPM INTRUDER
2x SATA III connectors
Storage 10
Display (VGA)/
2x SATA II Connectors
HDMI ports ATX power 7 FRONT PANEL 8 SATA3.0/2.0 9 USB CONNECTORS
8 x USB 2.0 ports, 12/480Mbps connector
USB CONNECTOR CONNECTORS
2 x USB 3.0 ports, 5Gbps
1x PS/2 Mouse/Keyboard RESET HDLED
+SBV +SBV

SATA_RX(+)
SATA_RX(-)

SATA_TX(+)
SATA_TX(-)
USB 2.0 ports USB*(-) USB*(-)
1x Display (VGA) port

Ground

Ground

Ground
HDLED( - )
HDLED(+)
USB*(+) USB*(+)

Ground
1x Display (DVI) port Ground Ground

Reset
Rear Panel I/O NC

NC
ports 1x HDMI port LAN (RJ-45) port SATA4
(Depending on 4x USB2.0 ports & USB3.0 ports
Model) SATA3
1x LAN (RJ-45) port + 2x USB2.0 ports

Ground
PWR
PLED( - )
PLED(+)
3x Audio jacks (5.1 CH) 9
Audio jacks
USB2.0 SATA2
1x ATX CPU power connector
System FAN 14 connector PWRBTN PLED
1x ATX power connector
SATA1 F_USB3
PCI Express slot (x16)
1x CPU fan connector FRONT PANEL F_USB2
1x System fan connector
4x SATA connectors PCI Express slot (x1)
Internal
connectors 1x Front panel audio connector 10 ATX POWER 11 ROM RECOVERY 12 CPU FAN
1x Front panel connector
CONNECTOR CONNECTOR CONNECTOR
1x Internal serial port connectors 8
SATA3.0/2.0
1x TPM (Trusted Platform Module) connector PCI slots connectors +3 Volts Ground
1x Chassis intrusion connector +12 Volts +5 Volts
+12 Volts +5 Volts
2 x USB 2.0 connectors +5V Standby +5 Volts
1x Clear CMOS selector & 1x Clear password selector ATX_PWRGD -5 Volts

CPU FAN PWM

CPU FAN TACH
CPU FAN PWR
Ground
Internal Selectors 7 Ground Ground
SPI_CS# SPI_CS
SPI_MOSI
1x ME Update Front panel +5 Volts Ground SPI_MISO +3P3VSB
connector Ground Ground SPI_CLK GND
BIOS SPI 64Mb (AMI) +5 Volts PSON#
Ground Ground
Form factor uATX, 9.6inches x 7.5 inches 1 2 3 4 5 B 6 A +3 Volts -12 Volts
Front panel SPDIF_OUT LPT header Serial port TPM header FLASH INTRUDER Clear CMOS +3 Volts +3 Volts
audio connector header OVERRIDE

ATXPOWER UEFI CPU_FAN

Conectores del panel trasero Selectores de función
13 ATX CPU POWER 14 SYSTEM FAN
Mouse (PS/2) Port SERIAL Port Display (VGA) port LAN (RJ-45) port A Clear CMOS B FLASH OVERRIDE CONNECTOR CONNECTOR
(Intel Management Engine) SELECTOR

+12V_CPU
Ground
Blue: Line Input
CLEAR CMOS FLASH_OVERRIDE
Ground
Lime: Front L/R Output 1 1 SYS FAN PWR
3 2 1 3 2 1 2 2 SYS FAN TACH
SYS FAN PWM
Pink: Mic Input Normal Clear Enable Disable

+12V_CPU
Ground
(Default) CMOS (Default)

Keyboard Display (DVI-D) HDMI ports USB2.0 USB3.0

(PS/2) Port port
ATX_CPU SYS_FAN

Indicadores LED del puerto LAN

Para borrar los ajustes de usuario CMOS RTC RAM:
1. Apague el ordenador y desconecte el cable de alimentación.
2. Mueva el jumper para borrar el BIOS por 5 a 10 segundos,
Left (ACTIVITY) Right (LINK) luego mueva jumper por defecto.
Soporte técnico: 0810 - 7777 - 247
Green: Activity Orange: 1G Link 3. Conecte el cable de alimentación y encienda el equipo.
Green: 100M Link 4. Durante el proceso de arranque, entrar en la configuración del BIOS www.redcx.com
Off: No activity
para volver a entrar en la configuración del usuario. [email protected]
LAN port Off: 10M Link
Las imágenes son sólo ilustrativas.