Scribd
Upload
1K views7 pages

System 6000 Rfid Encoder pk3695 PDF

Uploaded by

Innocent Elongo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views7 pages

System 6000 Rfid Encoder pk3695 PDF

Uploaded by

Innocent Elongo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

dormakaba RFID Encoder

System 6000

Installation Instructions
PK3695 - 2019 - 03

EN
Table of Contents

1. System 6000 Encoder Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2. Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3. Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Parts List
- dormakaba RFID Encoder (P/N: CE74750)

- Ethernet Cable (Optional) (P/N: 71590-10)

- USB A to Micro B USB cable (P/N: 71680)

Prerequisites
Hardware: dormakaba RFID encoder version 1.012 or greater.

Software: System 6000 version 5.6.8 or greater.

Setup: You can use the power over Ethernet (POE) to apply power on your device or use the USB cable
connected to a 5V adapter.

The encoder communicates with a TCP/IP communication protocol.

The following ports must be open in the firewall:


TCP Port 28000 (Server Inbound)
TCP Port 9090 (Server Inbound)

© 2018 dormakaba USA, Inc. All trademarks and registered trademarks are the property of their respective owners.

2 dormakaba RFID Encoder PK3695 03-19


System 6000 Encoder Setup

1- Connect the USB cable to the computer and to the encoder.

2 - Open the CRS program and log in. Choose the “Add” option under Settings.

3 - Choose the “Kaba RFID” option under Network Encoder Type and press “Configure Kaba RFID”.

dormakaba RFID Encoder PK3695 03-19 3


System 6000 Encoder Setup

4 - Press the drop-down menu and select the encoder you would like to configure.
(The encoders MAC address should appear).

Enter in a Station ID.

Choose either the TCP/IP configuration or the USB configuration.

Select “Obtain an IP address automatically” for DHCP Configuration.

OR

Enter specific IP configuration for Static IP.

4 dormakaba RFID Encoder PK3695 03-19


Testing

1 - Log into Client, choose the System tab, and choose the Terminal Settings option.
Set the Encoder Station to the new Encoder Station ID.

2 - Attempt a key interrogation to test the encoder connection.

dormakaba RFID Encoder PK3695 03-19 5


Troubleshooting

USB cable must be attached whenever you are configuring the encoder.

After Configuration: Connect a USB Cable for USB communication or an Ethernet cable with POE for
TCP/IP communication.

**Do not connect USB cable to PC when configured for TCP/IP communication**
**If ethernet connection is not POE, use the included USB power adapter for power**

Connection Issues:

• Ensure the encoder’s Station ID is selected in the Client Terminal Settings

• Ensure that Kaba Encoder USB Bridge Service is running

• Ensure that Kaba IP Encoder Service is running (KIPES)

• Ensure the CRS is running

• Ensure you are using the correct cable (USB or Ethernet)

• Confirm that the minimum prerequisite software (System 6000 5.6.8.0) and firmware (Encoder
V.1.012) is installed

• Remove the power from the encoder, wait five seconds and power it back up (Repeat as
necessary)

• Restart KIPES and Kaba Encoder USB Bridge Service

• Restart PC

Configuration Issues:

• Make sure that the encoder is not already assigned in the CRS

• Make sure that the USB cable (P/N 71680) is attached. (Third party cables may not function
properly)

• Ensure station ID entered was less than 16 characters

• If server not correctly assigned on workstation, do the following:


Edit the Saflok.ini file located in the SaflokV4 folder to enter the server IP address under the
database section. Save the file and test encoder function.

Example:
[Database]
LinkPath=\\xx.xxx.xxx.xx\SaflokData\
MsgLinkPath=\\xx.xxx.xxx.xx\SaflokData\

6 dormakaba RFID Encoder PK3695 03-19


dormakaba USA Inc.
Customer Services & Support
Saflok: 1.800.999.6213 / + 1.248.837.3700

General Information:
dormakaba.us
Online Consumable Orders:
www.saflokstore.com
To access all of our easy steps, please
visit our Support Website:
www.kabalodgingsupport.com

Subject to change without notice


PK3695 03-19

www.dormakaba.com

You might also like