Experiment 1: Calibration of Analytical Balance Group Members: Cruz, Danielle

DANIELLE V.
CRUZ
MD 1Y2-3
EXPERIMENT 1: CALIBRATION OF ANALYTICAL BALANCE
GROUP MEMBERS:
*CRUZ, DANIELLE*
VEROY, TARAH DENISE T.
GAROL, DANNICA
SALVADOR, NOY VILLARUEL
VILLAMORAN, ANN LOREIN
FIGUEROA, SHIN
ALINGASA, LUIGI
GARRUCHO, YZEL
Date performed: November 18, 2019

Date submitted: December 29, 2019
ABSTRACT
The formal lab report consists of analyzed data with respect to the first experiment performed
regarding the calibration of the analytical balance using the weight by taring method.
Consequently, the formal report will also discuss the significance of each data presented that is
concluded from the said experiment.
INTRODUCTION
There are different types of laboratory balance, it includes; toploading balances, portable
balances, analytical balances, semimicrobalances, and microbalances. A balance is a crucial and
fundamental piece of equipment for any laboratory. The one mainly used by the class MD 1y2-3
of Our Lady of Fatima University is the analytical balance type.
According to adamequipment.com (2018) Analytical balances are highly sensitive lab

instruments designed to accurately measure mass. Their readability has a range between 0.1mg
1
DANIELLE V. CRUZ
MD 1Y2-3
- 0.01mg. Analytical balances have a draft shield or weighing chamber to prevent the very small
samples from being affected by air currents. They're meant to detect very fine increments, so
the slightest vibrations or breeze can impact the results. In other words, analytical balances are
very sensitive materials which is why they are needed to be checked and calibrated frequently.
Calibration is a process of ensuring and maintaining the accuracy of a weighing instrument in

alignment with a standard or accepted range of results. Therefore, calibration is considered the
process of correcting, determining and checking the analytical balance is meeting its known or
assigned accuracy.
MATERIAL USED
 Analytical Balance  10 pieces of 25 centavo peso coins
METHODOLOGY
In order to do the calibration of the analytical balance. First, the analytical balance was turned
on. The analytical balance was then tested to see if it is working and functional, if there are any
poorly functioning balance it is reported to the instructor immediately. subsequently, the
balance was tared before placing anything. Then, the beaker has its pre-weigh recorded and the
ten 25-centavo coins was placed constantly and had its mass recorded each time the mass
changes. Each measurement was estimated in the nearest ± 0.0001g. Thereupon, after placing
all 10 coins, the slope, Y-intercept, R2 was calculated with conjunction to the calculation of the
mean, standard deviation and %RSD.
2
DANIELLE V. CRUZ
MD 1Y2-3
RESULTS AND DISCUSSION
Number of 25- Mass of beaker Mass of Mass of Precision by Percent by

centavo peso + mass of beaker, g sample, g sampling, g difference, %
coin sample, g
1 37.894g 34.318g 3.576 g 3.576 g 0.00%
2 41.540g 34.318g 7.222 g 3.646 g 1.96%
3 45.150g 34.318g 10.832 g 3.610 g .987%
4 48.680g 34.318g 14.362 g 3.530 g 2.22%
5 52.303g 34.318g 17.985 g 3.623 g 2.63%
6 55.878g 34.318g 21.560 g 3.575 g 1.32%
7 59.516g 34.318g 25.198 g 3.638 g 1.76%
8 63.120g 34.318g 28.802 g 3.604 g .935%
9 66.707g 34.318g 32.389 g 3.587 g .472%
10 70.307g 34.318g 35.989 g 3.600 g .362%
Table1. Results for Calibration test of analytical balance using 25¢ coins
Table1 shows the number of 25¢ coins, the mass of the tare weighed coins, the mass of the
beaker, Mass of beaker added with mass of the coins, the precision by sampling, and the
percent by difference of the experiment done. All formulas used in the computation can be
cited at the appendix. In the graph presented below the Number of 25¢ coins is in the X-axis
since it is the independent variable. And the mass of the tare weighed coins are at the y-axis
due to its dependency to the Number of 25¢ coins, since the mass cannot go higher unless
another coin is added.
Slope y-intercept R2
3.60g -2.47 0.9999955255
3
DANIELLE V. CRUZ
MD 1Y2-3
Table2. Computation for Linear Regression
The linear regressions which are: the slope, Y-intercept and R 2 are calculated and are presented
above which is the table 2. The slope was calculated and had a result of 3.60, then the y-
intercept which intersected the y-axis at (0,-2.47) and R 2 which is 0.9999955255 that is
acceptable based on the standard value of the R2 which is 0.9995.
Mean Standard Deviation %RSD

3.60 9.47x10-03 2.6306%
Table3. Determination of Mean, Standard Deviation and %RSD
Table 3 is about the mean, standard deviation and %RSD. The mean was calculated and had a
results of 3.60, a standard deviation of 9.47x10 -03, and a %RSD of .947%. The Mean is calculated
in order to find out the average of the samples. After that is the standard deviation in which the
variability of the results can be determined. And lastly, the %RSD is 2.6306%.
4
DANIELLE V. CRUZ
MD 1Y2-3
The graph shows the results linear regression on which the line is represented to indicate the
slope, and the R2 which is used to determine the curvature of the line, hence the lines curvature
is .9999 it is hard to tell on where the curve is, since the R 2 had a reliable result.
CONCLUSION
The experimentation conducted concluded that analytical balances does not always show a
perfectly accurate and precise result due to errors that might occur in the midst of the
experiment. Nonetheless even though the results was not perfect, it still had a low %RSD of
2.6306% meaning that even though the data isn’t perfect it is still precise due to the low %RSD
and that the analytical balance is properly calibrated.
APPENDICES
Appendix A
Mass of sample = (Mass of beaker + Mass of sample) – Mass of Beaker
Precision by sampling = New Value (mass of sample) – Old Value (mass of sample)
5
DANIELLE V. CRUZ
MD 1Y2-3
Percent by difference = [New Value (Precision by sampling) – Old Value (Precision by

sampling)] x100 Old Value (Precision by
sampling)
Appendix B
Slope = ((y2-y1)) ((x2-x1))
=3.60g
y- Intercept = mx + b
= -2.47g
R2 = [n(Σxy)-( Σx)( Σy)] ÷ √{[nΣx2-(Σx)2][ nΣy2-(Σy)2]
= 0.9999955255
Appendix C
Mean = Σn ÷ #n
= 3.60g
Standard Deviation = √[(Σx-x ̅ )2/(n-1 )]
= 9.47x10-03
%RSD= (σ)/x ̅) x 100
= 2.6306%
REFERENCES
Admin, I. (2019, September 20). Internal or External Calibration for Weighing Scales: Which is
Right for You? Retrieved from https://www.inscale-scales.co.uk/blog/internal-or-external-
calibration.
Equipment, A. (2019, June 19). Adam Equipment. Retrieved from

https://www.adamequipment.com/aeblog/what-are-analytical-balances.
6
DANIELLE V. CRUZ
MD 1Y2-3

Experiment 1: Calibration of Analytical Balance Group Members: Cruz, Danielle

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Experiment 1: Calibration of Analytical Balance Group Members: Cruz, Danielle

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Experiment 1: Calibration of Analytical Balance Group Members: Cruz, Danielle

Uploaded by

Copyright:

Available Formats

DANIELLE V.

EXPERIMENT 1: CALIBRATION OF ANALYTICAL BALANCE

Date performed: November 18, 2019

According to adamequipment.com (2018) Analytical balances are highly sensitive lab

Calibration is a process of ensuring and maintaining the accuracy of a weighing instrument in

RESULTS AND DISCUSSION

Number of 25- Mass of beaker Mass of Mass of Precision by Percent by

Table2. Computation for Linear Regression

Mean Standard Deviation %RSD

Table3. Determination of Mean, Standard Deviation and %RSD

Percent by difference = [New Value (Precision by sampling) – Old Value (Precision by

Equipment, A. (2019, June 19). Adam Equipment. Retrieved from

You might also like