Fact File Compilation of SDI Technical D PDF

Fact File
Compilation of SDI Technical Documents and

ANSI/SDI Standards and Test Methods
Updated August 2016
Please visit www.steeldoor.org for the

latest version of the Fact File.
____________________________________________________________________________________
Steel Door Institute
30200 Detroit Road · Westlake, OH · 44145 · TEL 440-899-0010 · FAX 440-892-1404 · [email protected]
Steel Door Institute Publications
Summary of Documents Provides a description of each technical document
ANSI/SDI-100-91 See ANSI A250.8-03 (R2008)
SDI-105-98 See ANSI A250.11-2012

SDI-107-84 See ANSI A250.6-2003 (R2009)
SDI-108-10 (R14) Recommended Selection and Usage Guide for Standard Steel Doors
SDI-110-09 Standard Steel Doors and Frames for Modular Masonry Construction
Recommended Details for Standard Steel Doors, Frames, Accessories
SDI-111-09
and Related Components
111-A Recommended Standard Steel Door Details
111-B Recommended Standard Details for Dutch Doors
111-C Recommended Louver Details for Standard Steel Doors

Recommended Door, Frame and Hardware Schedule for Standard Steel
111-D
Doors and Frames
111-E Recommended Weatherstripping for Standard Steel Doors and Frames
Recommended Existing Wall Anchors for Standard Steel Doors and
111-F
Frames
Recommended Standard Preparation for Double Type (Interconnected)
111-G
Locks on Standard Steel Doors and Frames
111-H High Frequency Hinge Preparations for Frames
Zinc-Coated (Galvanized/Galvannealed) Standard Steel Doors and
SDI-112-08 (R14)*
Frames
Standard Practice for Determining the Steady� State Thermal
SDI-113-13
Transmittance of Steel Door and Frame Assemblies
SDI-117-13 Manufacturing Tolerances for Standard Steel Doors and Frames
Basic Fire Door, Fire Door Frame, Transom/Sidelight Frame, and Window
SDI-118-12
Frame Requirements
SDI-122-15 Installation Troubleshooting Guide for Standard Steel Doors and Frames
SDI-124-16 Maintenance of Standard Steel Doors and Frames
SDI-127 Series - Industry Alerts (A through L)
SDI-127-A-06 (R14)* End Closure

SDI-127-B-06 (R14)* Door Edge Cutouts
SDI-127-C-06 (R14)* Frame Cutout Limits
SDI-127-D-06 Electric Strikes in Stud Walls
SDI-127-E-06 (R14)* Prime Painted Materials Alert

SDI-127-F-02 (R14)* Butted Frames Rough Opening Sizes
Environmental Considerations Relating to Factory Painted Steel Doors
SDI-127-G-06 (R14)*
and Frames
SDI-127-H-02 (R14)* Water Penetration
SDI-127-I-04 (R14)* Grouting Frames in Drywall
SDI-127-J-04 Back-Coating of Frames
SDI-127-K-09 (R14)* Improper Wedges as Hold-Opens
SDI-127-L-09 (R14)* Buyer Beware: Steel Doors with Lead-Based Primer

Guidelines for Acoustical Performance of Standard Steel Doors and
SDI-128-16 (R14)*
Frames
SDI-129-14 Hinge and Strike Spacing
SDI-130-15 Electrified Hinge Preparations
SDI-131-15 Accelerated Physical Endurance Test Procedure for Steel Doors

SDI-133-16 Guideline for Specifying Steel Doors and Frames for Blast Resistance
SDI-134-14 Glossary of Terms for Hollow Metal Doors and Frames

ANSI/SDI A250.3-2007 Test Procedure and Acceptance Criteria for Factory Applied Finish
(R2011) Coatings for Steel Doors and Frames
Test Procedure and Acceptance Criteria for Physical Endurance for Steel
ANSI/SDI A250.4-2011 Doors, Frames and Frame Anchors
ANSI/SDI A250.6-2003 Recommended Practice for Hardware Reinforcing on Standard Steel

(R2009) Doors and Frames
ANSI/SDI A250.8-2014 Specifications for Standard Steel Doors and Frames (SDI-100)
Test Procedure and Acceptance Criteria for Prime Painted Steel Surfaces
ANSI/SDI A250.10-2011
for Steel Doors and Frames
ANSI/SDI A250.11-2012 Recommended Erection Instructions for Steel Frames
Testing and Rating of Severe Windstorm Resistant Components for
ANSI/SDI A250.13-2014
Swinging Door Assemblies for Protection of Building Envelopes
*Document was reviewed by the Steel Door Institute Technical Committee and approved for
reaffirmation; ie., no revision was necessary to previously published document.
Summary of Documents
SDI-108 Recommended Selection and Usage Guide for Standard Steel Doors
This document was developed to establish guide criteria for the selection and usage of 1-3/4" and 1-
3/8" standard steel doors in such building types as apartment, dormitory, hotel/motel, hospital/nursing
home, industrial, office and school.
SDI-110 Standard Steel Doors and Frames for Modular Masonry Construction
This document contains information in respect to, as the title indicates, the installation of standard steel
doors and frames in modular masonry construction. The basic module covered in the document as
developed by the industry is 4".
SDI-111 Recommended Details for Standard Steel Doors, Frames, Accessories and
Related Components
This document is divided into seven sections, each dealing with a specific area as follows:
111-A covers recommended steel door frame details as they are affected by common wall conditions.
111-B is a document detailing standard dimensions for Dutch doors.
111-C is a document that discusses, explains, and details a variety of louver designs and size available
for standard steel doors.
111-D is a document that contains a suggested door, frame, and hardware schedule form and defines
"handing".
111-E contains details which represent the recommendations of the SDI in respect to weather-stripping
of standard steel doors and frames.
111-F is a guide for architects to aid them in recognizing available options to the traditional sub buck
detail that has been widely used in the past. It illustrates anchoring systems which are available in
regular and labeled frames.
111-G detailed dimensions for standard door and frame preparation for double type (interconnected)
locks.
111-H contains details of how extremely high frequency or high use areas which need to be supplied
with additional reinforcing to eliminate potential door sag.
SDI-112 Zinc-Coated (Galvanized/Galvannealed) Standard Steel Doors and Frames

This document provides information regarding the galvanized sheet used in standard steel door and
frame construction when a requirement for galvanized doors and frames is specified.
SDI-113 Standard Practice for Determining the Steady State Thermal Transmittance of
Steel Door and Frame Assemblies
This document establishes a minimum standard and a method of test for thermal effectiveness of steel
door and frame assemblies under circumstances that might reasonably be considered normal field
applications and conditions.
SDI-117 Manufacturing Tolerances for Standard Steel Doors and Frames

This document is intended to furnish users and prospective users of standard steel doors and frames
with practical information regarding mortise and manufacturing tolerances for both doors and frames.
SDI-118 Basic Fire Door, Fire Door Frame, Transom/Sidelight Frame, and Window Frame
Requirements
This document contains rules and other information in a condensed simplified manner in respect to
code requirements for the design and use of fire doors.
SDI-122 Installation Troubleshooting Guide for Standard Steel Doors and Frames
This document covers field installation problems most commonly experienced with standard steel door
and frame installations. Most problems encountered are because of inappropriate application of the
products and/or improper installation.
SDI-124 Maintenance of Standard Steel Doors and Frames

This document is intended to serve as a general outline of maintenance activities needed for hollow
metal doors and frames. It should be noted that the door and frame are virtually maintenance free.
Maintenance will be, for the most part, associated with accessories and hardware attached to the door
and frame.
SDI-127 Series - Industry Alerts (A through L)
127-A End Closure

127-B Door Edge Cutouts
127-C Frame Cutout Limits
127-D Electric Strikes in Stud Walls
127-E Prime Painted Materials Alert
127-F Butted Frames Rough Opening Sizes
127-G Environmental Considerations Relating to Factory Painted Steel Doors and Frames
127-H Water Penetration
127-I Grouting Frames in Drywall
127-J Back-Coating of Frames
127-K Improper Wedges as Hold-Opens
127-L Buyer Beware: Steel Doors with Lead-Based Primer
SDI-128 Guidelines for Acoustical Performance of Standard Steel Doors and Frames
This document shall provide guidelines for the specifying, designing, installing, and adjusting of standard
steel doors and frames in Sound Control applications.
SDI-129 Hinge and Strike Spacing

A reference of standard locations used in the manufacture of steel door and frames by SDI member
companies for a variety of door sizes.
SDI-130 Electrified Hinge Preparations

Practical information regarding an acceptable method for preparing frames for 4-1/2" electric hinges.
This document will allow frame manufacturers to provide frames prior to having knowledge of the
specific electric hinge being used.
SDI-131 Accelerated Physical Endurance Test Procedure for Steel Doors

This test procedure provides manufacturers with a method of quickly testing the performance of doors.
SDI-133 Guideline for Specifying Steel Doors and Frames for Blast Resistance
Serves as a guide on the specification of blast resistant door assemblies.
SDI-134 Glossary of Terms for Hollow Metal Doors and Frames
A250.3 Test Procedure and Acceptance Criteria for Factory Applied Finish for and
Frames
Prescribes the procedure to be followed in the selection of material, chemical preparation, painting,
testing, and evaluation of factory applied finish painted steel surfaces for steel doors and frames.
A250.4 Test Procedure and Acceptance Criteria for Physical Endurance for Steel Doors
A standard method of testing the performance of a steel door mounted in a pressed steel or channel
iron frame under condition that might be considered an accelerated field operating conditions.
A250.6 Recommended Practice for Hardware Reinforcing on Standard Steel Doors and
Frames
Provides users of standard steel doors and frames with practical information regarding accepted design
methods for reinforcing, and recommended practices for proper field preparation and installation of
builders’ hardware.
A250.8 Specifications for Standard Steel Doors and Frames (SDI-100)

The basic standard of the industry covers specifications for swinging steel doors and frames. It offers a
number of choices in both regular and fire rated door and frame construction design. The specification
covers sizes, types, materials, general construction requirements, and finishing of 1-3/4 ” and 1-3/8”
steel doors together with frames and accessories.
A250.10 Test Procedure and Acceptance Criteria for Prime Painted Steel Surfaces for
Steel Doors and Frames
Procedures for the selection of material, chemical preparation, painting, testing and evaluation of prime
painted steel surfaces for steel doors and frames.
A250.11 Recommended Erection Instructions for Steel Frames

This document includes information in respect to storage of frames on the jobsite, grouting and back
painting of frames and assembly of frames. It contains instructions in respect to bracing frames before
wall construction and the installation of frames in masonry, steel stud wall construction, wood stud wall
construction and drywall construction.
A250.13 Testing and Rating of Severe Windstorm Resistant Components for Swinging
Door Assemblies for Protection of Building Envelopes
This standard provides procedures for testing and establishing load ratings (design load in pounds per
square foot or pounds force) for components of exterior swinging door assemblies. It is the intent of this
document to test the protection of openings during severe windstorm conditions, such as a hurricane,
that produces sustained wind speeds or gusts in a range of 110 to 150 miles per hour as defined by ASCE
7-02. It is not intended to simulate wind forces generated by tornadoes.
SDI
TECHNICAL DATA SERIES
108 - 10
(Reaffirmed 2014)
Recommended
Selection and Usage Guide
for
Standard Steel Doors
STEEL DOOR INSTITUTE

30200 DETROIT ROAD • CLEVELAND, OHIO 44145
© 2015 Steel Door Institute
SDI-108
Recommended
Selection and Usage Guide
for Standard Steel Doors
Purpose Usage
To establish guide criteria for the selection and usage Selection of standard steel doors for general usage is
of 1-3/4" and 1-3/8" standard steel doors. made by analyzing criteria such as frequency of use,
including subjection to and degree of possible abuse.
Other criteria to be considered in door selection are:
Selection
conformance to local building codes and fire code
Standard steel doors are classified in four levels: regulations; sound attenuation and/or insulation re-
Level 1 – 1-3/4" and 1-3/8" standard duty, Level 2 – 1-3/4" quirements; and architectural design and appearance.
heavy duty, Level 3 – 1-3/4" extra heavy duty and
Table 2 is a reference aid matching standard duty,
Level 4 – 1-3/4" maximum duty.
heavy duty, extra heavy duty and maximum duty doors
Each of the four levels noted above offer a range of with general usage requirements within the classifica-
construction models and designs to meet architectural tion of buildings. Where optional door levels and models
requirements for preference and appearance. The are indicated, further analysis on an individual job basis
standard steel door construction models are full flush, is recommended.
seamless and, stile and rail.
When unusual or special door usage conditions are
Recommended minimum gauge requirements for the encountered, contact a representative member of the
various levels and models of standard steel doors are Steel Door Institute for consultation and guidance.
indicated in table 1.
Table 1 – Standard steel door grades and models

Full Flush or Seamless
Level Model Construction
MSG No. IP in SI mm
Standard 1 Full Flush
1 20 0.032 0.8
Duty 2 Seamless
Heavy 1 Full Flush
2 18 0.042 1
Duty 2 Seamless
1 Full Flush
Extra
3 Heavy 2 16 0.053 1.3 Seamless
Duty
3 *Stile & Rail
Maximum 1 Full Flush
4 14 0.067 1.6
Duty 2 Seamless
*Stiles and rails are 16 gauge; flush panels, when specified, are 18 gauge.
For complete standard steel door construction specifications and available sizes, refer to ANSI/SDI A250.8-2014,
Specifications for Standard Steel Doors and Frames (SDI-100) and ANSI/SDI A250.4-2011 Test Procedure and
Acceptance Criteria for Physical Endurance for Steel Doors, Frames and Frame Anchors.
Table 2 – Suggested door levels and applications
Standard Steel Door Levels Door Design Nomenclature

Level 1 Level 2 Level 3 Level 4
Building Standard Heavy Extra Maximum
Types Duty Duty Heavy Duty
1-3/8" Duty
1-3/4" 1-3/4" only 1-3/4" only 1-3/4" only F G V FG N L
Apartment
Main Entrance • • • • • •
Unit Entrance • • • •
Bedroom • •
Bathroom • • •
Closet • • •
Stairwell • • • •
Dormitory
Main Entrance • • • • • •
Unit Entrance • • •
Bedroom • • •
Bathroom • • • •
Closet • • • •
Hotel – Motel
Unit Entrance • • •
Bathroom • •
Closet • • •
Storage & Utility • • • •
Hospital – Nursing Home
Main Entrance • • • •
Patient Room • •
Operating & Exam. • • •
Bathroom • • • •
Closet • • • •
Recreation • • •
Kitchen • • •
Industrial
Entrance & Exit • • • • •
Office • • • •
Production • •
Toilet • • • •
Tool • • •
Trucking • • •
Monorail • • • •
Office
Entrance • • • •
Individual Office • • •
Closet • • •
Toilet • • •
Equipment • • •
Boiler • • • •
School
Entrance & Exit • • • • •
Classroom • • •
Toilet • • • •
Gymnasium • • • • •
Cafeteria • • •
Closet • • • • • •
Note: Table 2 is only a guide. Please consult ANSI A250.8 and applicable building codes for additional requirements. For ad-
ditional designs refer to SDI 134-2014, Nomenclature for Standard Steel Doors and Steel Frames.
Steel Door Institute Standard Steel Door Design Nomenclature
F T WG E2 E4 E6 E8 EWG D
L LL V VL* N NL* G EG GL*
G2 G2L* G3 G3L* G4 G6 FG FG3 FL
* Note: Design combination is indicated by light followed by louver.

Consult SDI/ANSI A250.7 for further information on standard design nomenclature for Standard Steel Doors.
Nomenclature Letter Symbols
F – Flush EWG – 6 Panel Embossed and Wood NL – Narrow Light and Louvered
T – Textured Grain G – Half Glass (options G2, G3,
WG – Wood Grain D – Dutch Door G4 and G6)
E2 – 2 Panel Embossed L – Louvered (top or bottom) EG – Embossed and Half Glass
E4 – 4 Panel Embossed LL – Louvered (top and bottom) GL – Half Glass and Louvered
E6 – 6 Panel Embossed V – Vision Light FG – Full Glass (option FG3)
E8 – 8 Panel Embossed VL – Vision Light and Louvered FL – Full Louver
N – Narrow Light
Louvered door designs are further specified as inserted louver (I), pierced (P), or air condition grille (A).
When ordering, specify design, louver size and/or free area requirements.
For the complete SDI Technical Data Series, contact the Steel Door Institute.

440/899-0010 • FAX 440/892-1404
www.steeldoor.org
SDI
110 - 09

and Frames
for
Modular Masonry Construction

SDI 110-09
Standard Steel Doors and Frames

for Modular Masonry Construction
The Module
Definition:
The size of any individual part, taken as a unit of measure for regular proportion. A basic unit of measure adopted
by the Building Industry as 4 inches.
Concept:
The use of a standard modular dimension common to building products such as masonry improves finished
structure by the following:
• Increased accuracy, legibility, and simplicity of working drawings and contract documents.
• Added aesthetic flexibility induced by small unit standardization, allowing freedom of architectural design.
Modular masonry construction meets the architectural need for blending and continuity of components.
Non-modular units interrupt a geometric pattern, or flow, by virtue of the discontinuity of line. As a specific
case, the use of a butted frame (Modular) is extremely important in stack bonded masonry unit construc-
tion. Any interruptions, such as cut units, unit lintels, wrap-arounds, etc, destroy the strong linear function
of such details.
• Increased flexibility of finished structure through lower modification, addition, and renovation costs.
• Reduced overall material and labor costs by facilitating the use of standard practices and definable operat-
ing procedures.
• Interchangeability of materials is facilitated by the ability to substitute modular components.
• Estimating and takeoff simplified.
• Detailing and drawing coordination between trades and specialties simplified by small size standard grid.
Dimensions:
Concrete masonry units (CMU) have been standardized to an 8" high and 16" long module. Also available are
“half blocks” standardized to a 4" high and 16" long module commonly used as a “starter course” shown on
page 4. The availability of loose “TEE” or wire masonry anchors can be an advantage over “fixed” masonry
anchors since they field adjust to masonry joints.
Modular bricks have been standardized to a 2 " high and 8" long module, therefore 6 bricks correspond to the
modular size of CMU. This relationship is clearly shown on pages 3 and 4.
Adjustments have been made in actual sizes to allow for common size mortar joints
2
SDI 110-09
Wrap Around Frame

6' 8" Door or 8' 0" Door
CL Joint CL Joint
/PUF
5IFNBTPOSZPQFOJOHGPSBOw
NPEVMBSEJNFOTJPOPQFOJOHBOEEPPS
PQFOJOHIFJHIUSFRVJSFTDPVSTFTPG
CMPDLPSDPVSTFTPGCSJDL Modular Modular Modular
Dimension Opening “X” Dimension
"WBJMBCMFJO
"$,1
.PEVMBS 4UBOEBSE
0QFOJOH GPS %PPS
i9w 8JEUI
4JOHMF4XJOH
w w
w w
w w
Opening & Door Opening Height 6' 8"

w w !
%PVCMF4XJOH
Modular Dimension
w w
w w "
w w
w w
w w
w w
w w
.BZ7BSZ
5ISPBUPQFOJOHCMPDL
XJEUIoww
Throat &INISH&LOOR'RID
Opening **
#, Joint #, Joint
3 ", 5 "
7 ", 11 " 2"* Modular Masonry
2"*
Opening “X”
$ETAIL,INTEL
ASREQUIRED
7 ", 11 "
Opening **
3 ", 5 "
6ARIES
Throat
$,1"
2"*
6ARIES #, *OINT
/PENING
-ODULAR
$,1" $,1"
Notch masonry for
hardware provisions
if required.
3%#4)/.n! 3%#4)/.n"
3
SDI 110-09
Wrap Around Frame

7' 0" Door
CL Joint CL Joint
Modular Modular Modular

"WBJMBCMFJO
"$,1
.PEVMBS 4UBOEBSE
0QFOJOH GPS %PPS
i9w 8JEUI
4JOHMF4XJOH
w w
w w
w w !
Opening & Door Opening Height 7' 0"
w w
%PVCMF4XJOH
w w
"
Modular Dimension
w w
w w
w w
w w
w w
w w
.BZ7BSZ
5ISPBUPQFOJOHCMPDL
XJEUIoww
Throat 3TARTER#OURSE &INISH&LOOR'RID

Opening **
#, Joint #, Joint
3 ", 5 "
7 ", 11 " 2"* Modular Masonry
2"*
Opening “X”
$ETAIL,INTEL
ASREQUIRED
7 ", 11 "
Opening **
3 ", 5 "
6ARIES
Throat
$,1"
2"*
6ARIES #, *OINT
/PENING
-ODULAR
$,1" $,1"
Notch masonry for
hardware provisions
if required.
3%#4)/.n! 3%#4)/.n"
4
SDI 110-09
Butt Type Frame

7' 2" and 7' 10" Doors or 7' 0" Door (X) 4" Header
CL Joint CL Joint
Modular Modular Modular

"WBJMBCMFJO
.PEVMBS 4UBOEBSE
0QFOJOH GPS %PPS
i9w 8JEUI
-ASONRY/PENING-ODULAR$IMENSIONgANDg
4JOHMF4XJOH
!g w w !
-ASONRY/PENING-ODULAR$IMENSIONg
w w
$OOR/PENING(EIGHTg ANDg
w w
%PVCMF4XJOH
$OOR/PENING(EIGHTg
w w
w w
" "
&INISH&LOOR'RID
-ODULAR-ASONRY
#, *OINT #, *OINT
3 ", 5 " /PENINGh8v
7 ", 11 "
$,1 $,1
$,13EC!h
Block
$,13EC!
$ETAIL,INTEL
ASREQUIRED
7 ", 11 "
3 ", 5 "
6ARIES
#, *OINT

-ODULAR/PENING
6ARIES
gANDg
g

3INGLE2ABBETED&RAME!CCEPTABLE
3%#4)/.n! 3%#4)/.n"
5
MEMBERS OF THE
AVAILABLE PUBLICATIONS STEEL DOOR INSTITUTE
Ceco Door
Specifications 9159 Telecom Drive
Milan, TN 38358
ANSI/SDI A250.6 Recommended Practice for Hardware Reinforcings on Standard (731) 686-8345
Steel Doors and Frames www.cecodoor.com
ANSI/SDI A250.8 SDI 100 Specifications for Standard Steel Doors & Frames
Curries
SDI-108 Recommended Selection & Usage Guide for Standard Steel Doors P.O. Box 1648
Mason City, IA 50402-1648
SDI-118 Basic Fire Door, Fire Door Frame, Transom/Sidelight Frame, and (641) 423-1334
Window Frame Requirements www.curries.com
SDI-128 Guidelines for Acoustical Performance of Standard Steel Doors & Deansteel Manufacturing Co.
Frames 931 S. Flores Street
San Antonio, TX 78204-1406
SDI-129 Hinge & Strike Spacing (210) 226-8271
www.deansteel.com
Test Procedures
DOOR COMPONENTS INC.
ANSI/SDI A250.3 Test Procedure & Acceptance Criteria for Factory Applied Finish 7980 Redwood Avenue
Coatings for Steel Doors & Frames Fontana, CA 92336-1638
(909) 770-5700
ANSI/SDI A250.4 Test Procedure & Acceptance Criteria for Physical Endurance for www.doorcomponents.com
Steel Doors, Frames and Frame Anchors
HOLLOW METAL XPRESS
ANSI/SDI A250.10 Test Procedure & Acceptance Criteria for Prime Painted Steel 602 S. 65th Avenue
Surfaces for Steel Doors & Frames Phoenix, AZ 85043
623-936-7000
ANSI/SDI A250.13 Testing and Rating of Severe Windstorm Resistant Components www.HMXpress.com
for Swinging Door Assemblies for Protection of Building Envelopes
(Not applicable for FEMA 320/361 or ICC-500 Shelters) Mesker Door, Inc.
3440 Stanwood Boulevard
SDI-113 Standard Practice for Determining the Steady State Thermal Huntsville, AL 35811-9021
Transmittance of Steel Door & Frame Assemblies (256) 851-6670
www.meskerdoor.com
SDI-131 Accelerated Physical Endurance Test Procedure for Steel Doors,
Frames and Frame Anchors MPI
319 North Hills Road
Corbin, KY 40701
Construction Details (606) 523-0173
ANSI/SDI A250.11 Recommended Erection Instructions for Steel Frames www.metalproductsinc.com
SDI-110 Standard Steel Doors & Frames for Modular Masonry Construction Pioneer Industries, Inc.
171 South Newman Street
SDI-111 Recommended Details for Standard Details Steel Doors, Frames, Hackensack, NJ 07601
Accessories and Related Components (201) 933-1900
www.pioneerindustries.com
SDI-122 Installation Troubleshooting Guide for Standard Steel Doors &
Frames Republic Doors & Frames
155 Republic Drive
McKenzie, TN 38201-0580
Miscellaneous Documents (731) 352-3383
SDI-112 Zinc-Coated (Galvanized/Galvannealed) Standard Steel Doors & www.republicdoor.com
Frames Security Metal Products
SDI-117 Manufacturing Tolerances for Standard Steel Doors & Frames 5700 Hannum Avenue, Suite 250
Culver City, CA 90230
SDI-124 Maintenance of Standard Steel Doors & Frames (310) 641-6690
www.secmet.com
SDI-127 Industry Alert Series (A-L)
SDI-130 Electrified Hinge Preparations Steelcraft
9017 Blue Ash Road
SDI-134 Nomenclature for Standard Steel Doors & Steel Frames Cincinnati, OH 45242
(513) 745-6400
AUDIO-VISUAL PROGRAMS ALSO AVAILABLE www.steelcraft.com

440.899.0010 • FAX 440.892.1404
12/4/2014
www.steeldoor.org
:+0
;,*/50*(3+(;(:,90,:
111-09
Recommended Details for

Standard Steel Doors,
Frames, Accessories
The information that follows represents the Standard Steel Door and Frame
Industry's considered views on a number of details normally encountered in
building plans and specifications.
The Steel Door Institute recommends that they be followed except when very
unusual details necessitate special drawings. The enclosed may be used as a
reference document or added directly to the job drawings.
:;,,3+66905:;0;<;,
+,;960;96(+*3,=,3(5+6/06
:[LLS+VVY0UZ[P[\[L
SDI 111-2009
Recommended Selection and Usage Guide
for Standard Steel Doors, Frames and Accessories
Table of Contents:
111-A Recommended Standard Steel Door Frame Details
111-B Recommended Standard Details for Dutch Doors
111-C Recommended Louver Details for Standard Steel Doors
111-D Recommended Door, Frame and Hardware Schedule for Standard Steel
Doors and Frames
111-E Recommended Guidelines for the Use of Gasketing and Thresholds for
111-F Recommended Existing Wall Anchors for Standard Steel Doors and Frames
111-G Recommended Standard Preparation for Double Type (Interconnected)
Locks on Standard Steel Doors and Frames
111-H High Frequency Hinge Preparations for Frames
Definition of “STANDARD”
We call our products Standard for three reasons:
FIRST, because our products are made to conform to published standards and
established dimensions.
SECOND, our products are manufactured to meet established performance
requirements.
THIRD, the fabrication of our products is controlled by standard manufacturing
procedures which ensure uniform high quality.
SDI
111-A
Recommended
Standard Steel Door
Frame Details

SDI 111-A
Hardware Locations
Door Opening Width
Up to 11 ¾"
(298.4 mm)
Center-Line
Equal Deadlock Strike
Door Opening
Height
48"
Equal (1219 mm)
38 - 42"
(965 - 1067 mm)
Up to 13"
(330.2 mm)
Center-Line Hinges Center-Line Lock Strike

& Panic Exit Device Strike
Note: Center Hinge Omitted on 6' 8" (2032mm), 1 ⅜" (34.5mm) Doors, Unless Specified.
Handing Chart
Inside Inside
KS KS KS KS
R.H. Outside L.H. L.H. Outside R.H.
ACTIVE ACTIVE
LHRB RHRB
RHRB Inside LHRB Inside
ACTIVE ACTIVE
Outside Outside
KS KS KS KS
KS indicates keyed side of lockset.
2
SDI 111-A
Standard Frame Details

Standard Profiles
2"
(50.8mm) Backbend Rabbet
Minimum 1/4" (6.3mm) Face
5/8" (15.8mm) min. Stop
Maximum 3/4" (19.0mm) Backbend
Return
Dimension
"A" Throat Jamb Single
Opening Depth Hardware
Throat Rabbet Throat Jamb
Jamb Rabbet
Opening Double Opening Depth
Depth
Rabbet
Stop May
Cased Soffit be applied
Opening
Minimum 1/4" (6.3mm)
Maximum 3/4" (19.0mm) Double Rabbet Single Rabbet Slip-On Drywall Double Egress
Door Thk. Dim. "A"
1-⅜" (34.9mm) 1-9⁄16" (39.6mm)
1-¾" (44.4mm) 1-15⁄16" (49.2mm)
Drywall
Corners
1" Gypsum Core 1-5/8" Steel or Wood

with 5/8" Gypsum Stud with 1/2 or 5/8"
Knocked Down Board with 1/2" or 5/8" Gypsum Board
Knocked Down (Butted) (Mitered) Gypsum Board
May be Horizontal or Vertical
Set Up Arc Welded
and Ground Smooth
2-1/2" or 3-5/8" Steel Stud

Slip-on Drywall (frame is 2-1/2" or 3-5/8" Steel or
with Two Layers of 5/8"
installed after the wall has Wood Stud with 1/2" or
Set Up Spot Welded Gypsum Board Each Side
been erected). Corner may 5/8" Gypsum Board
Mitered and Welded be screwed together, snap
Inside or Outside locked, or a slip fit design.
Common Wall Conditions
2" Solid Plaster with 1/2"

Gypsum Board Core
3" (78.2 mm) Precast

Stucco — 2 x 4 Wood Gypsum Tile with 5/8"
Butted Masonry, Brick 4" Block and Brick Stud with 3/4" Gypsum
Tile or Concrete Block (15.8 mm) Plaster
Combination Board & Plaster
Butted Masonry, Tile or

Concrete Block
2 x 4 Wood Stud with 3/4"

4" Block with 1/2" Plaster 2 x 4 Wood Stud with 3/4" Plaster on Metal Lath 2" Corner Tile and 4"
Plaster on Metal Lath Block Combination
Existing Masonry or Concrete
3
SDI 111-A
Special Frame Construction Details and Typical Hardware Preparations

Anchor Details
Masonry Wire Anchor Masonry Tee Anchor Wood Stud Anchor Steel Stud Anchor Existing Wall Anchor
Adjustable Base Anchor Standard Base Anchor Typical Mullion Sections Plaster Partition Anchor
with Base Anchor (Ceiling Strut Optional)
Special
Frame Details Hardware Preparations
Surface Hardware Reinforcement.

Weld-in Reinforcement Shown,
Loose Reinforcing Sleeve Available
Hospital Stop Rubber Silencers Mortise Hinge Strike for Field Installation.
For more information on steel doors and frames, contact any of the following members of the Steel Door Institute:
Black Mountain Door Deansteel Manufacturing Co. Mesker Door, Inc. Republic Doors & Frames
310 Flint Drive 931 S. Flores Street 3440 Stanwood Boulevard 155 Republic Drive
Mt. Sterling, KY 40353 San Antonio, TX 78204-1406 Huntsville, AL 35811-9021 McKenzie, TN 38201-0580
(859) 274-0411 (210) 226-8271 (256) 851-6670 (731) 352-3383
www.blackmountaindoor.com www.deansteel.com www.meskerdoor.com www.republicdoor.com
Ceco Door DOOR COMPONENTS INC. MPI Security Metal Products

9159 Telecom Drive 7980 Redwood Avenue 319 North Hills Road 5700 Hannum Avenue, Suite 250
Milan, TN 38358 Fontana, CA 92336-1638 Corbin, KY 40701 Culver City, CA 90230
(731) 686-8345 (909) 770-5700 (606) 523-0173 (310) 641-6690
www.cecodoor.com www.doorcomponents.com www.metalproductsinc.com www.secmet.com
Curries HOLLOW METAL XPRESS Pioneer Industries, Inc. Steelcraft

P.O. Box 1648 602 S. 65th Avenue 171 South Newman Street 9017 Blue Ash Road
Mason City, IA 50402-1648 Phoenix, AZ 85043 Hackensack, NJ 07601 Cincinnati, OH 45242
(641) 423-1334 623-936-7000 (201) 933-1900 (513) 745-6400
www.curries.com www.HMXpress.com www.pioneerindustries.com www.steelcraft.com

440.899.0010 • FAX 440.892.1404 • www.steeldoor.org
4
SDI
111-B
Recommended
Standard Details for Dutch Doors
“A”
6'-8" (2032mm), 7'-0" (2134mm), 7'-2" (2184mm),

Steel door Steel door frame
Mortise or 7'-10" (2388mm) & 8'-0" (2438mm)

surface dutch 1 ¾" (44mm)
door bolt Steel door
Steel Shelf
(optional)
L Strike
C
(254mm)
10" Max.
39" Min.
*(991mm)
Lock set
28 ½" Min.
(724mm)
Optional steel
shelf – Fasten
*Location is generally 40˝
but may vary as indicated
w/ S.M.S. in field
by specifier to suit local
*
accessibility codes.
Steel bracket
“A” 39" Min.
*(991mm)
ELEVATION Shelf may be
field installed
NON-FIRE RATED either side
Finished
floor
5 ½" Max. 5 ½" Max.
(140mm) (140mm)
¾" Max.
PLAN (19mm)
SECTION “A” - “A”

SDI 111-B
Top door latches

into top of bottom door
Flat astragal Flat astragal
Single point
Shelf latches Shelf
(optional) (optional)
Bottom door latches

into frame strike jamb
ELEVATION ELEVATION
FIRE RATED FIRE RATED
For more information on steel doors and frames, contact any of the following members of the Steel Door Institute
(859) 274-0411 (210) 226-8271 (256) 851-6670 (731) 352-3383

(731) 686-8345 (909) 770-5700 (606) 523-0173 (310) 641-6690

(641) 423-1334 623-936-7000 (201) 933-1900 (513) 745-6400

440/899-0010 • FAX 440/892-1404
www.steeldoor.org
SDI
111-C
Recommended
Louver Details
for
Standard steel doors can be provided with a variety of louver designs and
sizes. This publication contains explanations and details of louver designs
that are most commonly available within the standard door industry.
When specified, doors shall be provided with louvers at the bottom and/or top.
The choice of which to use must be determined by the architect on aesthetic,
functional, and economic grounds.

30200 DETROIT ROAD - CLEVELAND, OHIO 44145
SDI 111-C
Recommended Louver Details

for Standard Steel Doors
Function – Louvers permit free air passage, controlling Fusible link louvers are used in fire doors where flames
the volume by their size or design. They diffuse or control and intense heat passage must be controlled. The link
direction of air flow by blade design. release temperature recommended is 135°F (57°C). These
louvers must be labeled and may not exceed 24˝ x 24˝.
Insert louvers – Louvers commonly used in standard steel
Fusible link louvers are allowed only at the bottom of fire
doors are of the “insert” type designed to be mounted into
doors. Since closing is heat activated, these louvers are
a cutout in the door and an overlapping frame. Inverted
not to be used on smoke control doors.
“V” blade, “Z” blade, inverted “Y” or chevron-type blade,
lightproof, adjustable blade, grille type, and fusible link Pierced louvers, available from some steel door manufac-
self-closing fire door types are available in a wide range of turers, offer a flush condition and may be furnished with
sizes. Also available from some steel door manufacturers is internal insect screens. Louvers are formed by embossing
a pierced louver design. Insert louvers intended for exterior the door face sheets.
doors or other doors where security is a consideration
Louver size determinations – As a guide, the following
should have fasteners or materials specified accordingly.
approximate percentages of louver size may be used to
Note: If a louver door is required to provide security, the determine the free area in a given size louver:
steel door manufacturer should be consulted. • Pierced louver 20%
Bird or insect screens are available with many of the stan- • Inverted “V” inserted louver 50 – 60%
dard design louvers. Where specified, consult steel door • Inverted “Y” (chevron) inserted louver 40 – 60%
manufacturer for availability. • “Z” type inserted louver 40 – 45%
• Adjustable inserted louver 40 – 50%
Weatherproof louvers – True weatherproof designs do • Lightproof inserted louver 20%
not exist. Some louvers are manufactured to provide a • Fusible link inserted louver 45%
certain degree of rain protection.
The above percentages assume there is no air pressure
Louver construction – Standard louver frames are a mini- drop from one side of the door to the other. On air condition
mum 20 gauge steel with louver blades of a minimum 24 grilles an air pressure drop is normal. An average 70% of
gauge steel. The louver blades can be welded or tenoned the grille size can be used in computing free area on doors
to the frame and the entire assembly is generally fastened with air condition grilles.
to the door with moldings. Generally, one molding will be
The percentages noted above are approximates. Consult
an integral part of the louver, while the other molding will
the individual manufacturer’s literature for the specific sizes
be detachable. When louvers are installed, the detachable
and ratings normal to their program.
moldings should be located on the room or non-security
side of the door. Where doors are manufactured as non- Coordination – A combination of glass lights and louvers
handed, louvers may require reversing during door instal- is common in steel door work. Care should be taken to
lation to suit actual handing. avoid specifying too long a narrow light when a louver or
grille occurs in the bottom of the same unit. In addition,
Application:
handicap codes may dictate the location of the louver
Inverted “V” or “Z” blade types allow maximum free air relative to the bottom of the door.
flow with minimum static pressure differential.
Full louver doors – A minimum 5˝ (127.0mm) rail occurs
Inverted “Y” or chevron blade types, while offering less at the top and at the vertical stiles and an 8˝ (203.2mm)
free air flow, offer a higher strength factor for schools and minimum rail occurs at the bottom of these doors (Consult
other areas where vandalism or hard usage may occur. door manufacturer for exact stile/rail dimensions). Stile and
top rail sizes must be coordinated with closer dimensions,
Lightproof louvers are used where light transmission must
lock preparations, and lever handles. Pierced louvers are
be avoided, but provide minimal free air flow.
not available on full louvered doors.
Adjustable blade louvers are used where air flow is varied
Finish – The finish is to be prime painted, except when the
in velocity and control of flow is needed.
louver is used in a factory prefinished door, in which case
Grille type louvers are normally associated with air condi- the louver will be finish painted with a color to match the
tioning, where air must be diffused in random flow, avoiding door. For exterior doors, zinc coated louvers are available
higher velocity air flow patterns. where specified.
SDI 111-C
Cross Section Details
Operating
lever
Inverted “V” Blade Inverted “Y” Blade Chevron or Hood-Type Fusible Link
Blade
Insect screen
(optional)
Grille Pierced “Z” Blade Lightproof

SDI
111-D
Recommended
Door, Frame and
Hardware Schedule for
Standard Steel
Doors and Frames
The purpose of this publication is to establish a guide for architects and those responsible for scheduling doors,
frames, and hardware requirements.
Although primarily designed for steel doors and frames, this suggested schedule is flexible enough to list total
door and frame requirements of a complete job.
Items not specifically covered in the schedule may be listed in the “Remarks” and extra columns near the end.
Typical handing of doors and hardware is to be based on the format below:
Handing Chart
Inside Inside
KS KS KS KS
R.H. Outside L.H. L.H. Outside R.H.
ACTIVE ACTIVE
LHRB RHRB
RHRB Inside LHRB Inside
ACTIVE ACTIVE
Outside Outside
KS KS KS KS
KS indicates keyed side of lockset.

SDI 111-D
Door, Frame and Hardware Schedule
LOCATION FRAMES DOORS HARDWARE
DETAILS DOOR OPENING REMARKS

(3) (7)
(2)
HEAD JAMB SILL WIDTH HEIGHT
ITEM NO.
ARCH. NO
FROM
TO
QTY.
HAND
LABEL (1)
GAUGE (4)
ELEV. (6)
DEPTH
ANCHOR/
WALL TYPE
GAUGE (4)
TYPE (5)
HDWE.
GROUP NO.
HINGES
LOCK
CLOSER
General Notes:
(1) If a fire door is required, it is to be designated in the “Label” column of schedule with appropriate hourly rating. Also, note in the “Remarks” column whether
door is to have an Underwriters’ Laboratories (UL) Factory Mutual (FM), or Warnock Hersey (WHI) label.
(2) Thresholds, when required, are to be noted in “Hardware” column of schedule.
(3) Any special item not listed in schedule for doors, frames, or hardware is to be shown in the “Remarks” column.
(4) Indicate gauge of material for steel. When materials other than steel are used, indicate AL for aluminum or WD for wood.
(5) Refer to SDI-106 for Recommended Standard Door Design Nomenclature.
(6) When frame elevations are indicated, supplemental drawings must be attached.
(7) Doors provided with 3/4" undercut unless otherwise specified.
SDI
111-E
Recommended
Guidelines for the Use of
Gasketing and Thresholds
for Standard Steel
Doors and Frames
The following details represent the recommendation of The Steel Door Institute in this important corollary
area. This document should in no way be considered an endorsement of any manufacturer nor does it imply
that any materials not shown should be considered inferior weatherstripping.
The criteria employed in the selection of these details included:
1. The experience of the Institute with the details shown.
2. The adaptability of the material shown to standard steel doors and frames.
3. The ability to maintain gasketing at the door and frame during periods of
normal thermal movement to the balance of the building structure.
4. The availability of the material from normal commercial sources.
5. Ease of maintenance.
Disclaimer/Source Reference
Since the members of the STEEL DOOR INSTITUTE do not manufacture gasketing, it is strongly suggest
that the BHMA Members’ catalogs and BHMA documents be consulted to establish “fit and function” criteria
for specifying of any gasketing. BHMA Documents are available from:
Builders Hardware Manufacturers Association
355 Lexington Avenue, 15th Floor
New York, NY 10017
Phone: (212) 297-2122
Fax: (212) 370-9047
www.buildershardware.com

SDI 111-E
Recommended Guidelines for the

Use of Gasketing and Threholds
for Standard Steel Doors and Frames
General
Gasketing and thresholds are used to control the flow of air, smoke, heat or cold, water, sound or other environ-
mental factors through the door opening. The location or intended use of the door assembly, the environment to
which it is exposed, and the performance expected will dictate the selection of gasketing and threshold products.
The variety of materials, their composition, profiles, and performance are virtually limitless. These are described
in ANSI/BHMA A156.21 or A156.22. Generally, gasket materials are sponge neoprene, rubber, vinyl, brushes, or
magnets. Retainers are generally steel, aluminum, brass, bronze, vinyl, or other non-ferrous materials. Informa-
tion in catalogs published by BHMA members aid in the selection of perimeter sealing “ systems” to meet the
applicable performance criteria of the door assembly.
Perimeter Seals
Sealing of gaps between door edges and the header or jambs generally has the greatest effect on performance
of the door opening. The available options are as varied as their applications and their mounting surfaces e.g.
steel, structural steel, or wood. Care should be taken to select materials that will assure performance under
specific job requirements as well as meeting the mounting surface criteria.
brush
HEAD & Gasketing products should never impede the opera-

LATCH SIDE
tion, opening or closing of the door assembly. Simple
contact is all that is required for some products. Other
JAMB DOOR products for more severe installations require a slight
compression. A simple test for gasket compression
may be conducted by inserting a sheet of letterhead
paper into the gap and closing the door. The paper
JAMB DOOR should be held in place by the gasketing.
Gasketing or weather-stripping, of any kind, should be
furnished and installed in accordance with manufactur-
HINGE SIDE
ers instructions.
SDI 111-E
Door Bottom Seals

In most instances, sealing of gaps between the bottom of doors and flooring or thresholds is accomplished with
door bottoms or overlapping strips in metal retainers. These may be of a design that extends beyond the bottom
of the door mechanically, or of a fixed protruding or overlapping design.
Door bottom gaskets must compress against a solid object to affect a proper seal. Carpeting by its pliant nature
does not provide a proper seal.
brush
Automatic Door Bottom

Astragal Seals
Sealing of door edges at meeting stiles, in lieu of or in addition to factory mounted astragals is accomplished
by supplemental gasketing. This gasketing may be closely abutting fixed members or by overlapping strips in
metal retainers.
Overlapping gasketing is normally used to avoid interference with edge mounted hardware such as locksets
or flush bolts. Closely abutting gasketing is commonly used where both doors must operate simultaneously or
independently as in egress doors.
brush
Thresholds
Thresholds may be used in addition to or in lieu of door bottom seals. They may incorporate gaskets or other
formed profiles to allow for exit device latching or may be prepared for flush bolt latching. Thresholds should be
provided under the door and between the frame to allow for a smooth transition between floor coverings of dif-
ferent heights or materials. Special consideration should be given to threshold designs used in means of egress
or in handicap accessible situations. The latter limitations are covered in ANSI/ICC A117.1.
bumper insert available

*
bumper insert available

*
SDI 111-E
Fire Door Considerations

When supplying products to be used on fire rated openings, care should be taken to maintain the proper
clearances around the perimeter of the door assembly in accordance with NFPA 80. Gasketing materials
must be investigated or “Listed” to determine that their installation does not adversely affect the fire resis-
tance performance of the assembly. For example, the performance of gasketing is observed during the fire
test to ensure that flaming does not occur on the exposed surface of door assemblies. It is important to
note, however, that the ANSI/UL 10B, ANSI/UL 10C and ANSI/NFPA 252 standard fire tests do not include
evaluation of the door assembly relative to preventing the passing of smoke or other products of combus-
tion through or around the assembly. Openings that require a smoke seal must be tested in accordance
with NFPA 105, UL 1784 or UBC 7-2 Part 11, 1997. In fire door applications it is VITAL that gasketing does
not inhibit the ability of the door assembly to close and latch.
Performance Testing Criteria

Gasketing products are covered under ANSI/BHMA A156.22.
Included in that standard are:
• Closing Force test
• Heat Test
• Cold Test
• Air Infiltration Test
Thresholds are covered under ANSI/BHMA A156.21.
Included in that standard are:
• Weight bearing test
(859) 274-0411 (210) 226-8271 (256) 851-6670 (731) 352-3383

(731) 686-8345 (909) 770-5700 (606) 523-0173 (310) 641-6690

(641) 423-1334 623-936-7000 (201) 933-1900 (513) 745-6400

30200 DETROIT ROAD • CLEVELAND, OHIO 44145-1967
440.899.0010 • FAX 440.892.1404
www.steeldoor.org
SDI
111-F
Recommended
Existing Wall Anchors
for
and Frames

SDI 111-F
Recommended Existing Wall Anchors

This standard is a guide for architects to help them

recognize available options to the traditional sub
buck detail widely used in the past. The anchoring
systems shown are available in regular and labeled
frames.
NOTE A
The details shown are typical of those employed
Drill and form
by members of the Steel Door Institute, but all of countersink at
the details are not made by all of the members of center of frame
the Institute. A general reference to this document soffit for ¼˝ x 4 ¾˝
in your specifications should result in all of the FHMS or RHMS*
members of the SDI and most of the non-members
being able to bid on the job without a multitude of
exceptions.
In order to make the installation successful, care-
ful consideration shall be given to all tolerances
involved and that sufficient clearance is figured to
allow for them.
It has been “customary” to allow 1⁄4˝ clearance
around the frame perimeter when establishing
rough opening sizes or when figuring non-standard Adjustable Anchor
overall frame sizes. Although this dimensional re-
quirement does not appear in Industry publications,
it is based on the following:
NOTE B
• Both SDI 117-00 and ANSI/NAAMM HMMA Either bolt type
861-00 recognize a + tolerance in opening is available for
width and height. all anchors.
• Both of these documents recognize a ± toler-

ance in frame face dimensions.
• Both ANSI/NAAMM HMMA 861-00 and
SDI 117-00 recognize a ± installation tolerance
See note “A”
for vertical plumb.
Frames will “fit and function” if made to these dimen-
sional tolerances and installed within tolerances.
There is, however, relatively no assurance that the
substrate (walls) will be of suitable size or align-
ment.
We therefore recommend that the rough openings
for these cases be no less than 3/16˝ larger on all 3
sides than the “intended” overall frame size. (Exam-
ple: 3070 standard frame = 3´-4 3⁄8˝ x 7´-2 3/16˝). The
installer carries the responsibility for shimming and
aligning as necessary. Gaps are normally sealed as Lock-in "A" Anchor
part of the installation or caulking/painting process.
Architectural Specifications are to be consulted to
determine the appropriate sealant material to be
used at fire door or smoke control frames.
Weld to frame return SDI 111-F
See note “A”
Weld to frame return
See note “A”
Hat Anchor
Pipe Anchor
Hole plug
Lock-in "B" Anchor
Weld to frame soffit
See note “A”

NOTE C
The head of the bolt may be filled in field
with appropriate filler.
NOTE D
Up to 7´6˝ (2286 mm) height minimum
four (4) anchor required per jamb
* Fire rated frames require 3/8˝ (9.5 mm)

diameter bolts. Steel expansion shields
must be used instead of lead shields.
"C" Anchor
SDI
111-G
Recommended
Standard Preparation for
Double Type (Interconnected) Locks on
1" (25.4mm)
Sq. or Dia.
Clear Hole #8-32 Tap CL Door
2 ⅛" Dia.
(53.9mm) CL Door 2 Holes
5⁄32"
(3.9mm)
2 ⅛"
Lock 1 ⅝" (53.9mm)
CL (41.2mm) CL 1" 1 ⅜"
Strike (25.4mm) (34.9mm)
2 ¼" 2 ¾"
(57.1mm) (69.8mm)
Recommended Dimension
5⁄16"
(23.8mm) 1 ⅛" 5⁄16"
5 ½" (139.7mm)
(28.5mm) (23.8mm)
2 ¾" Backset 1" 1 ⅜" Door
(69.8mm) (25.4mm) (34.9mm)
2 ⅛" Dia. 1 ⅛" 1 ¾" Door
(53.9mm) (28.5mm) (44.4mm) ⅝" 1 ⅛"
(28.5mm)
(15.8mm)
2 ⅛"
Lock 1 ⅝" (53.9mm)
CL (41.2mm) 1 ⅜"
CL (34.9mm) 1" 1 ⅜"
Strike (25.4mm) (34.9mm)
2 ¼" 2 ¾"
40 5⁄16" (57.1mm) (69.8mm)
(1023.9mm)
Above Floor
5⁄32" CL Door 5⁄16"
(3.9mm) (23.8mm)
CL Door
5⁄16"
(23.8mm)
1" (25.4mm)
Sq. or Dia. #8-32 Tap
Clear Hole 2 Holes
DOOR FACE DOOR EDGE FRAME RABBET
Note: Minimum size of cutout as noted is subject to manufacturer’s standard clearance tolerances.

SDI
111-H
High Frequency Hinge Preparations for Frames
Door Door
frame frame
Weld (3) places

as shown
16 gage min.
auxiliary
reinforcement
Hinge
Reinforcement Weld (3) places
as shown
12 gage min.
auxiliary
reinforcement
Hinge
Reinforcement
Example “A”* Example “B”*
Background:
There are occasions where steel frames used in extremely high frequency or high use areas need to be supplied with
additional reinforcing to eliminate potential door sag. These types of openings would include: main entrances to schools,
rear exits where severe wind abuse could be a factor, auditoriums, gymnasiums, and the like. When these types of in-
stallations are required, there is a method in which this can be handled, efficiently and economically, through providing
auxiliary reinforcing to standard door frames. The specification for this is as follows:
Specification:
When a high frequency preparation is required, the top hinge of the door frame shall be provided with an auxiliary rein-
forcement as shown in example ‘A’ or ‘B.’ For additional strength, the center and bottom hinge reinforcement may also be
provided with additional reinforcements.
* High frequency hinge preparations may vary between manufacturers.

MEMBERS OF THE
Ceco Door
Milan, TN 38358
Curries
www.deansteel.com
Test Procedures
(909) 770-5700
HOLLOW METAL XPRESS
623-936-7000
www.meskerdoor.com
Corbin, KY 40701
155 Republic Drive
www.secmet.com
9017 Blue Ash Road
(513) 745-6400

440.899.0010 • FAX 440.892.1404
12/4/2014
www.steeldoor.org
SDI
112 - 08(Reaffirmed 2014)
Zinc-Coated
(Galvanized/Galvannealed)

SDI 112-2008
Zinc-Coated (Galvanized/Galvannealed) Steel Doors and Frames
Purpose Galvannealed steel doors and frames are fabricated

from carbon steel sheet that has been coated by
It is the intent of this document to provide information
the continuous hot-dip process and further treated
regarding the zinc-coated sheet used in steel door and
to convert the zinc coating into a zinc-iron alloy. The
frame construction when a requirement for zinc-coated
zinc coated sheet receives an in-line heat treatment
doors and frames is specified. It should be noted that
immediately as the strip exits the molten zinc bath to
doors and frames of cold rolled or hot rolled steel are
convert the entire coating layer to a zinc-iron alloy by
normally protected with a satisfactorily applied coat of
diffusion of iron from the sheet into the zinc coating.
rust inhibiting paint, and that zinc-coated doors and
The galvannealed surface has a non-spangled matte
frames need only be specified when they are to be
finish with a nominal composition of 90% zinc and
exposed to corrosive atmospheric conditions.
10% iron. This type of coating is referred to with an “A”
designation (or “ZF” in SI Units).
Applicable standards The galvannealed coating has several advantages
compared to the galvanized coating: 1) improved paint
ASTM A 924 / A 924M – Standard Specification for Gen- adhesion; 2) the coated surface accepts paint very
eral Requirements For Steel Sheet, Metallic-Coated by readily without a pretreatment (a pretreatment will en-
the Hot-Dip Process. hance the performance); 3) the zinc-iron alloy coating
ASTM A 653 / A 653M – Standard Specifications for can be welded more easily; and 4) the coating is harder
Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron and more resistant to manufacturing processes.
Alloy-Coated (Galvannealed) by the Hot-Dip Process.
Coating designations
Types of zinc coatings Coating designations are written to represent the coat-
Galvanized steel doors and frames are fabricated from ing type, either G or A (Z or ZF in SI Units), and the
carbon steel sheet that has been coated with zinc on coating weight. The coating weight is the amount of
two sides by the continuous hot-dip process. The pro- zinc on the steel surface and is expressed to represent
cess results in a layer of zinc on each side of the steel the ounces per square foot of zinc as the total weight
sheet that is tightly adhered to the steel sheet through on both surfaces of the steel sheet.
the formation of an iron-zinc alloy bonding layer that
is formed by a diffusion process while the heated steel
strip is in contact with the molten zinc. The relatively Minimum coating weights
pure zinc coating exhibits a bright metallic color with
There are two coating weights used to specify zinc-
a pronounced “spangled” appearance. These coatings
coated steel doors and frames. In a coating weight
have a free zinc spangled surface and may be pro-
of 40 there are 0.4 ounces of zinc per square foot of
cessed in a manner that reduces spangle and results in
steel, and in 60 there are 0.6 ounces of zinc per square
a smooth dull-gray appearance. This type of coating is
foot of steel.
referenced with a “G” designation (or “Z” in SI Units).
2
SDI 112-2008
Average coating thickness Painting

The average coating thickness specified in table 1 is Painting zinc-coated steel is recommended. In the fac-
based on the conversion factor of one ounce of zinc tory, steel is first chemically treated to ensure proper
coating per square foot of surface corresponding to an paint adhesion; then a factory applied coating of rust
average coating thickness of 0.0017" (0.043 mm). inhibiting primer is applied to the fabricated doors and
frames. When additional priming is required, care must
This coating thickness is not significant enough to make
be taken to ensure compatibility with the factory-applied
an appreciable difference in the measurable thickness
zinc surface.
of coated or uncoated steel of the same gage.
Refer to table 1 showing the coating designations,
minimum coating weights, and average coating thick- NOTES:
ness.
• Zinc-coating after fabrication is not available due
Corrosion resistance is directly proportionate to coating to thermal distortion of the product.
weight. The heavier the coating weight the more zinc is
• Although sometimes specified, the G Type zinc-
present and the more corrosion protection it will provide.
coating designation is not recommended for door
Therefore, under normal atmospheric conditions a 60
and frame construction.
designation will provide 50% more corrosion protection
than a 40 designation coating.
Table 1 – Coating designations, minimum coating weights, and average coating thickness
Coating Weight
Coating Average Coating
Designation Minimum Check Minimum Check Thickness / Side
Type
Limit Triple Spot Test Limit Single Spot Test
in-lb SI oz/ft2 * g/m2 * oz/ft2 * g/m2 * inches mm

G60 Z180 0.60 180 0.50 150 .0005 .013
Galvanized
G40 Z120 0.40 120 0.30 90 .0003 .009
A60 ZF180 0.60 180 0.50 150 .0005 .013

Galvannealed
A40 ZF120 0.40 120 0.30 90 .0003 .009
* NOTE: The weight of coating refers to the total coating on both surfaces.
3
MEMBERS OF THE
Ceco Door
Milan, TN 38358
Curries
www.deansteel.com
Test Procedures
(909) 770-5700
HOLLOW METAL XPRESS
623-936-7000
www.meskerdoor.com
Corbin, KY 40701
155 Republic Drive
www.secmet.com
9017 Blue Ash Road
(513) 745-6400

440.899.0010 • FAX 440.892.1404
12/4/2014
www.steeldoor.org
SDI
5&$)/*$"-%"5"4&3*&4
INDUSTRY ALERT -
4UBOEBSE1SBDUJDF
GPS
%FUFSNJOJOHUIF
4UFBEZ4UBUF5IFSNBM
Transmittance
of
Steel Door
and Frame Assemblies

%&530*530"%r$-&7&-"/% 0)*0
¥4UFFM%PPS*OTUJUVUF
SDI 113-13
:[HUKHYK7YHJ[PJLMVY+L[LYTPUPUN[OL:[LHK`:[H[L
;OLYTHSTransmittance of Steel Door and Frame Assemblies
1VSQPTF 1FSGPSNBODF 3BUJOHT

The purpose of this practice is to establish a
Table 1
standard test specimen size, test conditions
and a rating system for determining the thermal 67BMVF < ½ -JHIU > ½ -JHIU 3BUJOH
transmittance of operable steel door and frame
assemblies. > 0.46 >0.52 > 0.57 0
This practice refers to the standardized thermal ≤ 0.45 ≤ 0.51 ≤ 0.56 1
transmittance; Ust of an operable steel door and ≤ 0.43 ≤ 0.49 ≤ 0.54 2
frame assembly installed vertically in the absence
of solar and air leakage effects. ≤ 0.41 ≤ 0.47 ≤ 0.52 3
This practice employs the use of ASTM C1363-05, ≤ 0.39 ≤ 0.45 ≤ 0.50 4
Standard Test Method for Thermal Performance ≤ 0.37 ≤ 0.43 ≤ 0.48 5
of Building Materials and Envelope Assemblies
by Means of a Hot Box Apparatus, ASTM C1199- ≤ 0.35 ≤ 0.41 ≤ 0.46 6
09e1, Standard Test Method for Measuring the ≤ 0.33 ≤ 0.39 ≤ 0.44 7
Steady-State Thermal Transmittance of Fenestra-
tion Systems Using Hot Box Methods and ASTM ≤ 0.31 ≤ 0.37 ≤ 0.42 8
E1423-06 Practice for Determining Steady State ≤ 0.29 ≤ 0.35 ≤ 0.40 9
Thermal Transmittance of Fenestration Systems.
≤ 0.27 ≤ 0.33 ≤ 0.38 10
5FTU 4QFDJNFO
Single doors and pairs of doors shall be tested as 3FQPSU
nominal 3ƍ0Ǝ (914mm) wide x 7ƍ0Ǝ (2134mm) high The report shall contain the following information:
and 6ƍ0Ǝ (1828mm) wide x 7ƍ0Ǝ (2134mm) high
openings, respectively. A detailed description of the test specimen com-
ponents, i.e. Door, frame, hardware, glazing and
The test specimens shall consist of door, frame, weather-strip that includes model or series num-
weather-stripping system, glazing (if included) and bers.
hardware and be fully operable prior to the sealing
of the assembly. If the test specimen is of a size other than that
specified in Section 2.1, the reason for the devia-
/PUF ASTM E1423 requires sealing of the test
tion should be noted.
specimen to prevent air leakage.
All of the information specified in Section 9 of test
&YQFSJNFOUBM 1SPDFEVSF method ASTM C1199.
The specimen shall be tested in accordance with A statement affirming that the test was conducted
ASTM C1199, C1363 and E1423. in accordance with this standardized procedure.
$BMDVMBUJPO A rating as defined in Table 1.
The standardized Thermal Transmittance (Ust)
shall be calculated per the CTS method described
in ASTM C1199.

%&530*530"%r$-&7&-"/% 0)*0
r'"9
XXXTUFFMEPPSPSH
SDI
117 - 13
Manufacturing Tolerances
for
and Frames

+,;960;96(+*3,=,3(5+6/06
:[LLS+VVY0UZ[P[\[L
SDI 117-2013
Manufacturing Tolerances for Standard Steel Doors and Frames
1 Introduction NFPA 80, Standard for Fire Doors and Other Open-
It is the intent of this publication to provide users of ing Protectives, 2007 Edition (National Fire Protection
standard steel doors and frames with definitive infor- Association, 1 Batterymarch Park, Quincy, MA 02269;
mation regarding manufacturing tolerances. It is also www.nfpa.org)
intended to provide installation contractor(s) of the SDI 122, Installation and Troubleshooting Guide for
tolerances to be considered to assure proper operation Standard Steel Doors and Frames
of the complete opening. This document is intended for
in-plant inspections. It may be used for on-site inspec-
tions where there is no evidence of damage to material 3 Materials and Finishes
or improper installation.
The information contained herein pertains to doors 3.1 Steel Thickness
and frames manufactured in accordance with ANSI Manufacturers no longer order sheet and coil to a
A250.8, Recommended Specifications for Standard specific gage, but rather to a minimum decimal thick-
Steel Doors and Frames. It is not intended to reference ness. This thickness is the lowest of the range for a
to special or unusual door and frame conditions. specific gage. The steel supplier is therefore permitted
to exceed, but not be less than the specified decimal
thickness. These minimum values meet the stringent
2 Reference Documents: requirements of both Underwriters Laboratories Inc.
ANSI/SDI A250.8 SDI 100 Recommended Specifica- and ITS/Warnock Hersey. Examples of minimum al-
tions for Standard Steel Doors & Frames lowable steel thickness:
ANSI/SDI A250.6 Recommended Practice for Hard- Gage (MSG) Minimum
ware Reinforcings on Standard Steel Doors and
20 0.032˝
Frames
18 0.042˝
ANSI/SDI A250.7 Nomenclature for Standard Steel
16 0.053˝
Doors & Steel Frames
14 0.067˝
ANSI/SDI A250.3 Test Procedure & Acceptance 12 0.093˝
Criteria for Factory Applied Finish Coatings for Steel
10 0.123˝
Doors & Frames
7 0.167˝
ANSI/SDI A250.10 Test Procedure & Acceptance Cri-
Gage (MSG) are for reference purposes only.
teria for Prime Painted Steel Surfaces for Steel Doors
& Frames
ANSI/SDI A250.11 Recommended Erection Instruc- 3.2 Steel Coatings
tions for Steel Frames
Thickness of metallic coatings (generally zinc) are
ANSI/BHMA A115 Specifications for Steel Door and defined by ASTM A924, Standard Specification for
Frame Preparation for Hardware (A115.1 – A115.18) General Requirements for Steel Sheet, Metallic-Coated
by the Hot-Dip Process and A653, Standard Specifi-
ASTM A568 Standard Specification for Steel, Sheet,
cation for Steel Sheet, Zinc-Coated (Galvanized) or
Carbon, Structural, and High-Strength, Low-Alloy, Hot-
Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip
Rolled and Cold-Rolled, General Requirements for
Process. The two most commonly used designations
ASTM A653 Standard Specification for Steel Sheet, are A40 and A60. Minimum requirements for these
Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated designations are:
(Galvannealed) by the Hot-Dip Process
A40 = 0.40 oz/ft2 total both sides.
ASTM A924 Standard Specification for General Re- A60 = 0.60 oz/ft2 total both sides.
quirements for Steel Sheet, Metallic-Coated by the
For reference, 1 oz/ft2 = 1.7 mils thickness.
Hot-Dip Process
1
SDI 117-2013
3.3 Factory Applied Coatings 4.2 Frame Opening & Vertical Locations
Since factory applied coatings (primer, finish paint, etc.)
are subject to performance standards rather than thick-
ness, the dry film thickness is irrelevant. Such coatings
must comply with performance criteria of: ±-˝
ANSI/SDI A250.3 – Test Procedure and Acceptance C
L Hinge
Criteria for Factory Applied Finished Painted Steel
Surfaces for Steel Doors and Frames
±/˝
OR Opening
Height
ANSI/SDI A250.10 – Test Procedure and Acceptance +",1˝ –-˝
Criteria for Prime Painted Steel Surfaces for Steel ±/˝
Doors and Frames. CL
Strike
4 Frame Tolerances
±-˝
4.1 Frame Cross Section Profile

Permissible tolerances in frame profile surfaces are
as shown below:
Opening Width
+",1˝ –-˝
Face
±-˝
Stop Figure B – Opening Tolerances
±-˝
Rabbet
±-˝ 4.3 Bow or Twist of Jambs or Header
Realizing that frames are somewhat “pliable”, and
Throat
Frame require bracing and alignment during installation,
Depth Opening
±$.-˝ allowable deformation (bow, twist, etc.) of jambs or
±",1˝
header of frame prior to installation shall not result
in a reduction of opening sizes more than 1⁄16˝ beyond
those shown in Figure “B” when measured at any point.
Figure A – Profile Tolerances
2
SDI 117-2013
4.4 Horizontal Alignment of Door Within 5 Door Tolerances

Rabbet
Hinge and strike backsets shall allow the horizontal 5.1 Door Size, Thickness, and Vertical
centerline of the door to be in line with the horizontal Locations
centerline of the frame rabbet ± ⅓2˝ prior to installa-
tion. Figure “C” is an example based on a 1 ¾˝ door
in a 1 15⁄16˝ rabbet. Door Width
±$1/˝ Door
Thickness
±-˝
±",1˝
C
L Hinge
±/˝
Door
1˝ or $-˝ ± -˝ Height
±$1/˝
±/˝ C
L Lock
Centerline of door
Lock
Height
±-˝
1 ˝ door
Figure C – Horizontal Alignment

Figure E – Doors
4.5 Frames with Lights or Panels

Opening sizes (width or height) for side or transom
lights or panels and for borrowed light frames shall be
subject to a tolerance of ± 1⁄16˝ for each individual light or
5.2 Door Squareness
panel. These tolerances shall be non-accumulative so
that the overall frame opening sizes are not increased When measured diagonally from corner to corner along
by more than ⅛˝. the same face, the measurements shall be within 1⁄16˝
of each other.
± ˝
± ",1˝ ± ",1˝ ± ",1˝
± ",1˝
± ˝
± ",1˝ Figure F – Squareness
Figure D – Frames with Lights or Panels
3
SDI 117-2013
5.3 Door Perimeter Flatness

When a suitable straightedge is laid against the door
face at or within ¼˝ of the top, bottom, hinge edge,
and lock edge on both faces any deviation between
the face and the straightedge shall not allow a 0.0625˝
rod or block to pass.
Note: The straightedge shall be allowed to “rest” natu-
rally on the door surface, not pulled down at one end to
meet the door.
Straightedge
⅛˝ max
Straightedge
Door
Figure H – Flatness
",1˝ max
5.5 Door Twist

The door is laid onto a suitable, flat fixture or surface
",1˝ max that is free of any warp, bow, or twist. Support blocks of
identical heights shall be inserted between the fixture
and the door face at all four corners of the door. Any
deviation between the face and the support blocks shall
Straightedge
not allow a 0.0625˝ rod or block to pass.
Note: The door shall be allowed to “rest” naturally on
Figure G – Flatness the support blocks, not pulled down at any corner to
meet the blocks.
5.4 Door Face Bow or Crown

When a suitable straightedge is laid diagonally against
the door face at least ½˝ from corners any deviation
between the face and the straightedge shall not allow Flat
a 0.125˝ rod or block to pass. Surface
Door Surface
Note: The straightedge shall be allowed to “rest” natu-
rally on the door surface, not pulled down at one end to
meet the door.
",1˝ max.
Figure I – Door Twist
4
SDI 117-2013
5.6 Doors with Lights or Panels 7 Frame Installation and Door Adjustments
Opening sizes (width or height) for lights or panels cut
into doors shall be subject to a tolerance of ± 1⁄16˝ for 7.1 Adjusting Pivot Point by Shimming
each individual light or panel. Providing extra depth along door or frame faces allows
for hinge knuckles to be offset, thus changing the pivot
6 Hardware Preparations point of the opening. Shims are usually thin strips of ¼˝
wide material approximately equal to the hinge height.
6.1 Vertical Locations 7.1.1 Figure “J” shows how to relocate the pivot point
Tolerances for vertical locations are as noted in Para- toward the jamb.
graphs 4.2 and 5.1.
C
L Hinge
6.2 Horizontal Alignment Barrel Shim B
Hinge
Tolerances for horizontal alignment of door and rabbet Jamb Hinge
are as noted in Paragraph 4.4. Reinf.
6.3 Mortise Depth

The depth of hardware items mortised into edges of
doors (such as hinges, strikes, lock fronts, flushbolts)
shall be as defined on manufacturer’s templates and/ Door Shim A
or ANSI A156.115 documents subject to an additional “X”
tolerance of ± ⅙4˝.
6.3.1 Cutout Depth at Frame or Door Faces

In order to allow for field adjustment, usually ac-
complished by shimming, hardware cutouts (such as
r Using shim "A" only, door will be relocated in the direc-
hinges) that extend from door edges around to faces
tion of arrow "X".
or from frame rabbet around to faces are allowed to
exceed mortise depth by 1⁄16˝. See Paragraph 7 for r Using shim "B" only, will move both door and centerline
examples of common hinge shimming procedures. of hinge barrel in direction of Arrow "X".
r Using both shims "A" and "B" will relocate the door
in direction of Arrow "E" by a greater amount than by
6.3.2 Depth for Recessed or Concealed using shim "B" alone.
Hardware
The depth for hardware items recessed into top or bot- Figure J – Hinge Bind, Shims A and B
tom of doors or edges of doors (such as pocket pivots,
floor closers, top pivots, concealed closers or holders,
etc) shall be as defined on manufacturer’s templates
subject to an additional tolerance of +1⁄16˝ –0˝. Notches
in door faces shall have similar tolerances.
5
SDI 117-2013
7.1.2 Figure “K” shows how to relocate the pivot point 7.2 Frame Installation Tolerances
away from the jamb. While this document is mainly concerned with toler-
ances relating to the manufacturing process, openings
will not function properly if the frame is not installed
C
L Hinge within recognized tolerances.
Barrel Hinge Figures “L-M-N-O” show examples of the accuracy to
Jamb Shim D Hinge
Reinf.
be maintained while setting frames. Instructions for
installation may be found in ANSI A250.11.
",1˝ (1.58 mm)
Shim C
Door Strike
Hinge Jamb
“Y”
Jamb
",1˝ (1.58 mm)

r Using shim "C" only, door will be relocated in direction
of Arrow "Y".
r Using "D" only, both door and centerline of hinge barrel Strike
Hinge Jamb
will move in the direction of Arrow "F".
Jamb
r Using both shims "C" and "D" will relocate the door
in direction of Arrow "F" by a greater amount than by
using either "C" or "D" alone. The centerline of hinge
barrel will be relocated the same as by using shim Maximum 1/16” allowable tolerance on total opening.
"D" alone.
Figure K – Hinge Bind, Shims C and D Figure L – Squareness
Head Level Head Level

",1˝
(1.58 mm)
Hinge or Hinge or
Strike Jamb Strike Jamb
Bottom Bottom
",1˝
(1.58 mm)
Figure M – Plumbness
6
SDI 117-2013
",1˝ (1.58 mm)
Figure N – Alignment
",1˝ (1.58 mm)
Figure O – Twist
7.3 Troubleshooting
Further information regarding corrective actions for
door & frame openings may be found in SDI-122.
7
MEMBERS OF THE
Ceco Door
Milan, TN 38358
Curries
www.deansteel.com
Test Procedures
(909) 770-5700
HOLLOW METAL XPRESS
623-936-7000
www.meskerdoor.com
Corbin, KY 40701
155 Republic Drive
www.secmet.com
9017 Blue Ash Road
(513) 745-6400

440.899.0010 • FAX 440.892.1404
12/4/2014
www.steeldoor.org
SDI
-
)HZPJ-PYL+VVY
-PYL+VVY-YHTL
;YHUZVT:PKLSPNO[-YHTL
HUK>PUKV^-YHTL
9LX\PYLTLU[Z

+,;960;96(+*3,=,3(5+6/06
:[LLS+VVY0UZ[P[\[L
Technical Data Series SDI 118-2012
Basic Fire Door, Fire Door Frame, Transom/Sidelight

Frame, and Window Frame Requirements
1 Introduction 2.1 Hourly ratings
Fire testing of doors, door frames, transom/ Steel fire doors are “rated” by time (in minutes
sidelight frames, window frames, glazing, and or hours) that a door can withstand exposure
hardware and the resulting labeling programs to fire test conditions. Hourly ratings include
1-½-hours, 1-hour, ¾-hour, and ⅓-hour, with
granted by third-party testing agencies are
the maximum rating required of any swinging
complex subjects better understood when basic
type fire door being three hours.
rules and guidelines are applied.
2.2 Three-hour (180-minute) doors
2 Doors A door with a three-hour fire protection rating is
The fire rating classification of the wall into usually required in walls that separate buildings
or that divide a large building into smaller fire
which the door is installed dictates the required
areas. The wall rating is four hours.
fire rating of the door. The location of the wall
in the building and prevailing building codes 2.3 1-½-hour (90-minute) doors
establish the fire rating requirements for the Doors rated for 1-½ hours are required in 2-hour
wall. The associated door ratings are shown rated walls. These doors are commonly located
in Table 1 below. in stairwells, or other enclosures of vertical
Table 1 – Fire door openings
Wall Door and

Opening Description and Use
Rating Frame Rating
3 Hour These openings are in walls that separate buildings or

4 Hour
(180 minutes) divide a single building into designated fire areas.
Openings of this type are used in enclosures of vertical

1-½ Hour communication or egress through buildings. Examples
2 Hour
(90 minute) of these types of openings include stairwells and eleva-
tor shafts.
1 Hour These door and frame assemblies divide occupancies

1 Hour
(60 minute) in a building.
1 Hour
¾ Hour For use where there are openings in corridors or room
(45 minute) partitions.
1-½ Hour This opening is in a wall where there is the potential for
2 Hour
(90 minute) severe fire exposure from the exterior of the building.
This opening is in an exterior wall that has the potential

1 Hour
¾ Hour to be exposed to moderate to light fire from the exterior
(45 minute) of the building.
1 Hour
⅓ Hour These openings are in corridors where smoke and draft
(20 minute) control is required. The minimum wall rating is ½ hour.
1
SDI 118-2012
passage through a building. They also occur used in a 1-½- hour opening. All requirements
in boiler rooms and in exterior walls that have for the 3-hour rating, such as maximum glazing
the potential for severe fire exposure from the materials size, door size, and other restrictions
outside of the building. for the higher rated door must be met.
2.4 One-hour (60 minute) doors
3 Glazing Materials
One-hour rated doors are used in occupancy
separation walls, which are also one-hour rated. A wide variety of glazing materials and glazing
compounds are available for use in fire doors
2.5 ¾-hour (45 minute) doors and frames. Wired glass that is ¼Ǝ thick and
Doors with ¾-hour fire protection ratings are ceramic glass are the most common types of
used in one-hour walls. A ¾-hour rated door glazing used in fire rated doors. The hourly rat-
is required in walls of corridors and room ing of the door dictates the number and maxi-
partitions. A door with this rating may also be mum size of the vision lights used in the door.
located in the exterior wall of a building subject
For ¼Ǝ thick wired glass, the maximum ex-
to moderate fire exposure from the outside of
posed area for a transom light shall not ex-
the building.
ceed 1296 square inches with no dimension of
2.6 ⅓-hour (20 minute) doors exposed wired glass greater than 54Ǝ in width
or 48Ǝ in height, unless otherwise indicated in
One-third-hour or 20 minute doors are used in
one-hour walls. These doors are used for corri- the individual glazing manufacturer’s published
dor applications and in other applications where listings. Wired glass, ¼Ǝ thick is rated for ¾-
smoke and draft control is a primary concern. hour for an exposed area not exceeding 1296
square inches.
2.7 Twenty-minute doors tested without
hose stream For glazing materials other than ¼Ǝ thick wired
glass and for ¼Ǝ thick wired glass in sizes larger
Doors and frames may also be rated as 20 than those described above, the maximum ex-
minutes without a hose stream. These doors posed area per individual light, the minimum
have successfully passed a 20-minute fire test, groove depth, glazing compound and the rating
with the omission of the hose stream test, and
shall be as indicated in the individual glazing
bear a label that specifically states “Twenty-
manufacturer’s published listings. Consult with
Minute-Rating Tested Without Hose Stream.”
the door and glazing manufacturers for the
These doors may be provided with vision lights
limitations of size, area and number of vision
only limited in size by the door manufacturer’s
lights in a door. The approved listings for fire
fire labeling procedure authority.
door, transom/sidelight frame, window frame,
Assemblies identified as “Twenty-Minute-Rating and glazing manufacturers may be obtained
Tested Without Hose Stream” should not be through the listing agencies as follows:
confused with ⅓-hour fire rated doors, which
have been tested in accordance with the stan- Underwriters Laboratories
dard fire test procedure that includes the hose Use the following hyperlink to access the Under-
stream test. writers Laboratories “Online Certifications Direc-
2.8 Summary tory”. Enter the “UL Category Code” indicated
below for a listing of approved manufacturers.
Doors are rated for three-fourths of the rating
of the surrounding wall: A 3-hour door is used http://database.ul.com/cgi-bin/XYV/template/
LISEXT/1FRAME/index.htm (link valid as of
in a 4-hour rated wall; a 1-½-hour fire door is 9/30/2013)
used in a 2-hour rated wall; and a ¾-hour door
is used in a one-hour rated wall. The notable
Fire Door Manufacturers – GSYX or GSZN
exception is that ⅓-hour rated doors are also
used with one-hour rated walls.
Fire Door and Window Frame Manufactur-
However, a door with a higher fire rating than ers – GVTV
the opening requires may also be specified.
For example, a door rated for 3 hours may be Glazing Manufacturers – KCMZ or CCET
2
SDI 118-2012
Intertek Testing Services (Warnock Hersey) designed to restrict the transmission of heat
and are referred to as temperature rise doors.
Use the following link to access the Intertek
“Listed Product Directories”. Enter keywords In addition to the hourly rating, the fire door
such as glass, glazing, fire door, fire door label will also state the temperature rise rating
frame, fire window, or transom frame for a list of the door. Temperature rise ratings are 250°F,
of approved manufacturers. 450°F, and 650°F, and indicate the maximum
https://whdirectory.intertek.com/Pages/DLP_ rise in temperature above ambient temperature
Search.aspx (link valid as of 9/30/2013) measured on the unexposed surface (non-fire
Vision lights are not allowed in 3-hour rated side) of the door during the first 30 minutes of
fire doors, unless allowed by the local author- the standard fire test. The 250°F temperature
ity having jurisdiction. The vision light kit or rise designation is the most stringent rating of
window frame must be approved for use in a the three, since it requires the most limiting rise
fire rated door. in temperature. A 250°F temperature rise door
meets the requirements of specifications calling
Two categories of glazing used in doors, door
for a 450°F or 650°F temperature rise rating.
frames, transom/sidelight frames, and borrowed
light frames are available as follows:
5 Louvers
Fire-Protection-Rated Glazing – This glaz- Listed louvers are permitted in 1-½-hour and ¾-
ing is evaluated for fire protection ratings hour fire doors and the louver must be installed
measured in minutes or hours in doors in in accordance with the manufacturer’s listing.
accordance with UL 10c and NFPA 252 Louvers may not be used in ⅓-hour (20-minute)
and frames in accordance with UL 9 and rated doors, or doors of other hourly ratings that
NFPA 257. may be part of a smoke and draft assembly.
Doors with glass lights, or doors equipped with
Fire-Resistance-Rated Glazing – Fire-re-
fire exit devices may not have louvers unless
sistance-rated glazing is designed to limit
permitted by local building codes.
the temperature rise on the unexposed
surface in accordance with UL 263 and
6 Fire door frames
ASTM E119. Performance is rated in terms
of temperature rise on the unexposed face Fire door frames are not affected by the expo-
at increments of time (minutes or hours). sure ratings and opening classifications that
This glazing may be used in Temperature apply to doors. There are no hourly ratings for
Rise Doors which are explained in the a basic fire door frame unless the labeling on
next section. the frame specifically states that the frame is
Fire protection and fire resistance glazing in- rated less than 3 hours. Some state and local
stalled in fire doors and fire windows that are building codes require hourly ratings up to
subject to human impact shall meet applicable and including 3 hours for a door frame. If a
impact safety standards (e.g. – 16 CFR 1201, frame bears a recognized label qualifying it as
U.S. Consumer Product Safety Commission, a fire door frame, it may support a 3-hour, a
“Standard for Architectural Glazing”). 1-½-hour, a ¾-hour, or a ⅓-hour door. Frames
used in masonry walls may be used with a
4 Temperature rise doors maximum 3-hour fire door, while frames used
In certain applications, fire doors are required in drywall stud walls are intended to be used
to minimize the transmission of heat from one with a maximum 1-½-hour fire door. Consult
side of the door to the other, as in the stairwell with individual fire door frame manufacturers
of a high-rise building or in horizontal exits. If listings for fire door frames that can be used
the door can limit the transmission of heat for a in drywall stud walls with a maximum 3-hour
period of time, people can safely pass below the rating. Grout is not required for fire rated frames
floor of fire origin in a burning building. These installed in either drywall or masonry walls at
doors are built with a core that is specifically any hourly rating.
3
SDI 118-2012
7 Transom and sidelight assemblies 9 Fire doors with Builders Hardware

Labeled door frames are available with tran- Fire doors with Builder’s Hardware serve four
som areas, sidelight areas, or a combination main purposes:
of both. The transom and sidelight areas can 1) To function as a door at all times; 2) to provide
be assembled with listed panel assemblies or ready egress; 3) to keep fire from spreading
listed glazing material. Frames with solid tran- throughout the building; and 4) to protect life
som panel and/or side panels may be used in and property.
openings rated up to and including 3 hours.
To adequately perform these functions, a fire
Transom and sidelight frames with labeled glaz-
door must be equipped with labeled hardware
ing material may be used in openings rated up
for dependable operation. Proper hardware
to 1-½ hours. The maximum hourly rating, overall
selections can be verified by consulting the
frame size, panel construction, and individual current editions of the “Fire Resistance Direc-
glazing material exposed areas for frame and tory” published by Underwriters Laboratories
glazing manufacturers may be obtained through Inc. and “Directory of Listed Products” published
the listing agencies as indicated in Section 3. by Intertek Testing. These directories identify
The overall size of transom and sidelight hardware and other products that may be used
frames is limited to the maximum size that a in fire-rated assemblies. The information can
manufacturer has successfully fire tested. Since also be accessed at the following links:
the size may vary, it is important to consult the Underwriters Laboratories
manufacturer when writing specifications. http://database.ul.com/cgi-bin/XYV/template/
LISEXT/1FRAME/index.htm (link valid as of
Some testing agencies require that the label 9/30/2013)
applied to transom or sidelight assemblies shall
state whether panels or glazing materials are Use UL Category Codes GXHX or GYJT.
to be used in the frame. If the frame contains
both panels and glazing materials, the label Intertek Testing Services (Warnock Hersey)
for the glazing materials is used since it is the https://whdirectory.intertek.com/Pages/DLP_
Search.aspx (link valid as of 9/30/2013)
most limiting rating.
NFPA 80 provides guidance for installing fire
8 Fire window frames (borrowed light) doors, frames, and hardware in the building
openings.
Fire window frames are labeled hollow metal
glass light frames that are not attached to a 9.1 Hinges
door frame and are tested in accordance with A labeled fire door must be hung on steel ball-
NFPA 257 or UL 9 and shall be provided in bearing-type or listed hinges. NFPA 80 allows
accordance with the manufacturer’s listing. the use of steel hinges with steel ball-bearings
Individual glazing material exposed areas are without a listing. Steel hinges that meet the
not to exceed 1296 square inches and the di- criteria of NFPA 80 have been proven to be
mension for width or height shall not exceed 54 adequate during a fire. There are certain hinge
inches unless otherwise tested. The maximum designs made of non-ferrous metals which may
hourly rating, overall window size, and individual be used on fire doors in accordance with the
glazing material exposed areas for frame and listing information for the particular hinge but
glazing manufacturers may be obtained through may result in a lower fire rating.
the listing agencies as indicated in Section 3. Hinges with ball bearings are required in order
Fire window frames are typically used in cor- to provide smooth operation and to minimize
ridor walls and may be provided for masonry or wear throughout the lifetime of the opening.
drywall construction. Consult the frame manu- Remember, a fire door must close in the event
facturer as to the ability to supply fire window of a fire. Worn hinges will cause the door to
frames for drywall walls. Grout is not required sag, effectively preventing the door from closing.
for fire rated frames installed in either drywall Exception: Some manufacturers may provide
or masonry walls at any hourly rating. doors with hinges that use other antifriction
4
SDI 118-2012
bearing surfaces if they meet the requirements capability of the door to allow the hardware to
of ANSI/BHMA A156.1. operate in a panic situation.
NFPA 80 allows the use of standard weight Care must be taken when selecting exit devices
(0.134 inch leaf thickness) 4-½Ǝ steel hinges for use on fire-rated doors, as some devices
as a minimum on 1-¾Ǝ doors up to 4ƍ-0Ǝ in have been tested for panic loading only, and
width and 8ƍ-0Ǝ in height. Doors over 8ƍ-0Ǝ in not fire tested. In addition, exit devices have
height shall have heavy weight (.180 inch leaf size and hourly rating restrictions, and must
thickness) 4-½Ǝ hinges as a minimum. Some
be properly labeled and identified as fire exit
manufacturers have the capability of providing
hardware.
lighter weight hinges on doors over 8ƍ-0Ǝ in
height as part of a listed assembly. (Consid- 9.4 Closing devices
eration should be given to larger hinge sizes
A properly sized closing device is the last of the
for frequently used or heavy doors.)
“basic” fire door hardware requirements. A fire
9.2 Latching devices door must be in a closed and latched position
Every swinging fire door must have a labeled to serve as a protective barrier in the event
self-latching device. Dead bolts may be provided of a fire. For this reason, either listed spring
in addition to the latch bolt, except on doors hinges or a listed door closer is required to
in a means of egress, in which case intercon- ensure that the door will close properly.
nected locks may be used which retract the
Note: Per NFPA 80, the authority having juris-
dead bolt with the latch bolt. Dead bolts may diction may allow the closer to be omitted from
not be used in place of latch bolts. the inactive leaf of a pair of doors for equipment
rooms to allow the movement of equipment.
When selecting latching devices, it is impor-
tant to use the correct length of latch bolt, a 9.5 Hold open devices
requirement that can vary with the door con-
struction and the manufacturer’s fire testing Tests and investigations have proven that smoke
program. It is common for a pair of doors to and toxic gases are the main cause of death in
require a longer latch bolt throw than a single fires. Listed closers with closer arms that are
door. The minimum latch bolt length that must equipped with a fusible link or a listed combi-
be used for any given door is indicated on the nation closer/holder shall be used. Mechanical
fire door label. hold-open only devices and hold-open only
arms are not permitted on self-closing doors.
An exception to latching for fire rated open-
Doors with surface closers equipped with a
ings is allowed by the IBC for double egress
doors in corridors that are in a smoke barrier. listed hold open device (e.g. electromagnetic
The omission of positive latching devices must release) also prevent the passage of the toxic
be included in the door manufacturer’s listing. gases and smoke. These devices are activated
State and local building code authorities may by electronic detectors that sense smoke and/
also allow latching to be omitted in certain or the products of combustion.
openings. Consult individual manufacturers for
labeling capabilities. 10 Hardware – pairs of doors
9.3 Fire exit hardware Pairs of doors for rated openings have some
unique hardware requirements.
Fire exit hardware devices may be used on
labeled doors provided the door labeling spe- 10.1 Hinges and closing devices
cifically states “Fire Door To Be Equipped With
Fire Exit Hardware.” This label indicates that the Pairs of doors for labeled openings require steel,
door has been properly reinforced for fire exit ball-bearing-type hinges or a listed continuous
devices. Fire exit hardware used on doors that hinge. Closing devices are required on both
bear this label must pass a panic loading test leaves of a pair of doors except on mechanical
in accordance with UL 305 and ANSI/BHMA equipment rooms where the closing device may
A156.3 in addition to the standard fire test. be omitted from the inactive leaf, if acceptable
The panic load test measures the structural with the authority having jurisdiction.
5
SDI 118-2012
10.2 Latching hardware 11 Product labeling

10.2.1 Active leaf of pairs of doors There are several materials and attachment
methods for fire labels that are approved by
An active leaf of a pair of doors may require
recognized labeling agencies. These include
labeled fire-exit hardware, or any labeled latch
steel, brass, aluminum, and non-metallic ma-
that shall be opened by one obvious operation
terials such as foil and mylar. Metal labels are
from the egress side.
attached with welds, rivets, drive screws, or
10.2.2 Inactive leaf of pairs of doors adhesive. Non-metallic labels are either die-slit
or tamper proof with an adhesive back. Once
Local codes may allow manual flush or surface
applied, if any attempt is made to remove the
mounted bolts to be used to secure the inactive
label it will tear apart indicating tampering. Em-
leaf of pairs of doors being used as entrances
bossed metal labels and embossments directly
to equipment rooms or similar situations. The applied to doors and frames may be painted as
IBC requires that the inactive leaf have no knob long as the listing agency mark and all listing
or other visible hardware that implies means information is legible.
of egress.
The mark of a labeling agency shall be provided
Labeled fire exit devices are mandatory for exits on all labels applied to fire-rated doors and
unless local authorities give specific approval for frames. The agency mark or manufacturer isn’t
the use of labeled self-unlatching and latching required to be the same on the door, frame, and
devices, such as automatic flush bolts on the hardware. Labels are located on the edge of a
inactive leaf. The self-unlatching feature must door between the top and middle hinges. Labels
work only when the active leaf is opened. are located on the frame rabbet between the
10.3 Double egress pairs top and middle hinges. Labels may be located
on the top of the door or head of the frame if
Double egress pairs of doors should only be there is interference with hardware (e.g. electric
provided with vertical rod fire-exit hardware power transfer, continuous hinge, smoke seals)
devices on both leaves. The vertical rod devices that would obscure the label.
may be either surface mounted or concealed.
Fire labels on doors and frames are not intended
10.4 Astragals to survive a fire. The label is there to indicate
that the opening is protected by a properly
The application of astragals on pairs of doors
constructed steel door and frame.
depend upon the individual door manufac-
turer’s published listings. Pairs of doors that
12 Fire test methods
do require an astragal shall have at least one
that projects a minimum of ¾-inch beyond the There are two primary fire test methods that
edge of the door to which the astragal is at- are used to establish the fire ratings of doors.
tached. Pairs of doors that are in a required The first is ANSI/UL 10B and is referred to as
means of egress may not be equipped with an neutral pressure; the second is ANSI/UL 10C,
astragal that inhibits the free use of either leaf. and is referred to as positive pressure.
An overlapping astragal may not be used on The difference between the two test methods
pairs of doors swinging in the same direction concerns the location of a neutral pressure
with vertical rod exit devices on both leaves plane in the test furnace. In the late 1990’s, the
of the pair. test method required in building codes changed
In some situations a coordinator may be needed to a positive pressure test method. This change
to allow the inactive leaf to close before the was adopted by the International Building Code
active leaf. This ensures proper latching of pairs (IBC) for swinging-type fire doors.
of doors. Some manufacturers are able to sup- Fire doors required to be tested to either method
ply labeled pairs of doors with an open-back may be specified by calling out the test method
strike without an astragal, which eliminates the or by indicating that the product must meet a
need for a coordinator. specific section of a model building code.
6
SDI 118-2012
13 Smoke and draft control to inspect all components of the opening and
Doors that open into corridors that are used for document the results. Adjustments and compo-
a means of egress may be required to have a nent replacement are required if the opening
smoke and draft control rating. Smoke and draft does not comply with the code requirements.
control assemblies are tested for air leakage
per UL 1784 and NFPA 105 and fire protection 17 References
ratings as previously discussed.
ANSI/BHMA A156.1-2006 “American National
13.1 Gaskets
Standard for Butts and Hinges”
Gaskets are required for doors to pass a smoke
and draft control test. The requirement for a ANSI/BHMA A156.3-2008, “American National
gasket also includes the meeting edges of a Standard for Exit Devices”
pair of doors. The gaskets used in a smoke and
draft control assembly must be fire rated and ASTM E119-11 “Standard Test Methods for Fire
be listed for use in a smoke and draft control Tests of Building Construction and Materials”
assembly. A bottom seal is not required for
smoke and draft control assemblies. NFPA 80-2010 “Standard for Fire Doors and
Other Opening Protectives”
13.2 Marking
The IBC requires smoke and draft control as- NFPA 105-2010, “Standard for the Installation
semblies to have an identification mark of “S” of Smoke Door Assemblies and Other Opening
which appears on the door label following the Protectives”
hourly rating. The frame doesn’t require the
“S” mark. NFPA 252-2008 “Standard Methods of Fire
Tests of Door Assemblies”
14 Smoke barrier doors
NFPA 257-2007 “Standard Methods of Fire Tests
The IBC includes a requirement for smoke bar-
of Window Assemblies”
rier doors. These doors need to provide smoke
and fire protection as previously described in Underwriters Laboratories Standard for Safety
this document. The IBC includes an exception
ANSI/UL 9 “Fire Tests of Window Assemblies”
for double egress doors that require that these
doors have the same characteristics of a fire Underwriters Laboratories Standard for Safety
door except a fire protection rating and self
ANSI/UL 10B “Fire Tests of Door Assemblies”
latching are not required. Double egress doors
used in a smoke barrier are used in cross cor- Underwriters Laboratories Standard for Safety
ridor applications. ANSI/UL 10C “Positive Pressure Fire Tests of
15 Field modifications Door Assemblies”
Clarifications for field modifications were added Underwriters Laboratories Standard for Safety
to NFPA 80 in 2007. If the product or compo- ANSI/UL 263, “Fire Tests of Building Construc-
nent requires a field modification, the agency tion and Materials”, 13th Edition, April 4, 2003,
that the product or component was listed with
revisions up to and including October 24, 2007
shall be provided with the description of the
modification. The agency will not have to con- Underwriters Laboratories Standard for Safety
duct a field inspection if they determine that ANSI/UL 305, “Standard for Panic Hardware”,
the modification does not affect the integrity
and fire protection capabilities of the opening. 2007
Underwriters Laboratories Standard for Safety

16 Fire door inspections
ANSI/UL 1784, “Air Leakage Tests of Door As-
NFPA 80 incorporated a requirement for an- semblies”, 2001
nual fire door inspections in the 2007 version
of the standard. Building owners are required International Building Code 2009
7
MEMBERS OF THE
Ceco Door
Milan, TN 38358
Curries
www.deansteel.com
Test Procedures
(909) 770-5700
HOLLOW METAL XPRESS
623-936-7000
www.meskerdoor.com
Corbin, KY 40701
155 Republic Drive
www.secmet.com
9017 Blue Ash Road
(513) 745-6400

440.899.0010 • FAX 440.892.1404
12/4/2014
www.steeldoor.org
S D I
122 - 15
Installation
Troubleshooting Guide
for
Standard

30200 DETROIT ROAD · CLEVELAND, OHIO 44145
This page left intentionally blank.
Contents
Improper Door / Frame Clearance................................................................................. 1
Hinge Bind Against Rabbet............................................................................................ 6
Hinge Bind Against Stops.............................................................................................. 7
Twisted Door.................................................................................................................. 8
Twisted Door Adjustments............................................................................................. 9
Twisted Frame..............................................................................................................11
Frame Set out of Square............................................................................................. 12
Frame with Rabbets Toed In or Out............................................................................. 16
Silencers...................................................................................................................... 18
Lock Fits Loose on Strike............................................................................................ 19
Lock Fits Too Tight in Strike......................................................................................... 20
Lockset Off Location on Door or Strike Off Location in Frame in Wall......................... 21
Miter Not Closed on Frame.......................................................................................... 22
Clearance at Bottom of Door Too Small....................................................................... 23
Frame and Door Hinge Misalignment.......................................................................... 24
Frame Loose on Drywall.............................................................................................. 26
Glazed Window Units.................................................................................................. 30
Label Missing from Fire-Rated Frame......................................................................... 31
Label Missing from Fire-Rated Door............................................................................ 32
Paint Problems............................................................................................................. 33
Water Stain Damage................................................................................................... 34
Thermal Bow............................................................................................................... 35
Foreword
The material contained in this document has been developed under the auspices of the Technical
Committee of the Steel Door Institute.
The Steel Door Institute does not condone or encourage repair methods which would adversely affect
product performance or violate and/or void product warranties.
The user of this document assumes all responsibility associated with but not limited to product
performance and violation of product warranties for any product associated with the installation and
suggested repair methods in this document.
Purpose
The intent of this document is to cover field installation problems most commonly experienced with
standard steel door and frame installations. It should be understood that most problems encountered are
because of inappropriate application of the products and/or improper installation.
The suggested method of repairs requires only basic hand tools and relatively little time. It should be
understood that more complex problems or compound problems could exist which warrant extensive field
repairs and modification to products. These types of field installation problems are not intended to be
covered in this document and should not be made without first consulting the manufacturer.
Modifications made to fire-rated-labeled doors and frames shall be made in compliance
with NFPA 80.
SDI-122
Installation Troubleshooting Guide
Improper Door / Frame Clearance

To ensure proper door and frame function, the clearance between the door and frame must be properly
maintained. All standard steel door and frame manufacturers closely hold tolerances that result in
a nominal clearance between the door and frame of 1/8 inch. If this clearance is not maintained,
interference and hardware misalignment may occur.
Proper installation is extremely important in establishing clearances and preventing a multitude of potential
problems.
The Steel Door Institute has many publications which were developed to establish industry standards
and assist in specifying as well as installing standard steel doors and frames. One publication, ANSI/SDI
250.11, Recommended Erection Instructions for Steel Frames, will be of assistance regarding the erection
and installation of standard steel frames.
Even clearance
EVEN between door and UNEVEN
1/8 1/8
frame – all around –
nominal 1/8″
1/8 between edge of
door and rabbet
UNEVEN
EVEN
UNEVEN
EVEN
CONSISTENT CLEARANCE INCONSISTENT CLEARANCE
Even Clearances Uneven Clearances
1
SDI 122-2015
Improper Door / Frame Clearance (continued)
Is door sagging?
Uneven clearances frequently result from improper
installation of frames and frame anchors. The
condition, characterized by lock edge clearances
narrow at the top and wide at the bottom, is called
“door sag”. The following suggested adjustments
may correct the condition
Are hinges loose?

If hinge screw does not remain tight, the screw can
be held in place by the use of a “locktite” type product
which prevents the screw from loosening. Additionally,
“Nyloc” type fasteners can be used to replace the
normal machine screws.
Are hinges worn?

If excessive wear has occurred on hinge knuckles, the
door will not be held tightly. Replace hinges.
Are hinges properly swaged?

The hinge manufacturer’s specifications
should be checked to determine what the
proper hinge swage should be.
Standard swaging of
Swaging is a slight offset of the hinge leaf standard-weight and
at the barrel which permits the leaves to heavy-weight full mortise
come together. hinges, when closed to the
parallel position, provides
a 1⁄16″ clearance between
leaves.
2
SDI 122-2015
Remove top hinge filler for non-

handed doors
The improper clearance condition may be
improved by removing the top hinge leaf
attached to the door and taking out the filler
(hinge filler) from behind the leaf. Once
completed, reattach hinge leaf to door. A hinge
filler is used on all non-handed doors.
Add shims to bottom and/or middle

hinge
On handed or non-handed doors, the lower half
of the door can be shifted upward and toward
the strike jamb. Remove the screws which
attach the middle and/or bottom hinge(s) to the
door. Insert shims between the hinge leaf and
door. Reattach hinge leaf to door.
Standard-weight to heavy-weight hinge modifications

Although styles and types vary, many manufacturers offer built-in features that allow hinge pockets
on doors and frames to be modified from standard-weight to heavy-weight. Examples of the different
methods are: grinding or flattening down raised embossments in shim plates or reinforcements; removing
or breaking off hinge filler shim plates; adjusting set screws; and removing wire shims. These options
all involve removing material from the pocket to allow for heavy-weight depth to be achieved. As always,
check with individual manufacturers to determine the type of modifications offered.
3
SDI 122-2015
HEADER
Reswaging hinges
The following example shows how a hinge leaf
can be reswaged to correct minor improper door/
frame clearances. This particular method allows
HINGE the reswaging to be accomplished while the door
PIN remains in the opening and the hinge leaves
remain on the door and frame. The example
shows a top hinge reswaged to correct a sag-
HINGE JAMB type condition. However, any of the hinges can
be reswaged in this manner to compensate for
conditions opposite to that of a sag condition.
1. Remove top hinge pin.

DOOR LOCK
EDGE
STRIKE JAMB
CLEARANCE
2. Use a screwdriver to set the clearance between

the lock edge of the door and strike jamb.
HINGE LEAF
KNUCKLE ON FRAME
HINGE LEAF
KNUCKLE ON DOOR
3. Hinge knuckle will now be misaligned.
4
SDI 122-2015
Reswaging hinges (continued)

As shown, the hinge leaf knuckles on the door move
to a new location once the clearance at the strike
jamb is set. The hinge leaf knuckles on the frame
must now be reswaged (bent) to align with the new
location of the hinge leaf knuckles on the door. The
simplest way to do this is to use a 5/8″ – 11/16″ tube
wrench (a crescent wrench will do as a second 5/8
choice). Simply slip the tube wrench down around the

1st knuckle and align it with the new location. Once the 1ST
first knuckle has been aligned, the wrench will now 2ND
slip down to the 2nd knuckle for alignment. Repeat the 3RD
process on the third knuckle.
4. Reswage and align hinge knuckles.
HINGE PIN
NOTE: As always, caution should be

exercised when the hinge leaves are
not removed. Excessive pressure
could damage doors/frames. As an
alternate reswaging method, the hinge
can be removed and clamped in a vise
for reswaging.
5. Re-insert the hinge pin and remove the screwdriver.
Is the door binding?

Frames which are out of plumb will likely cause
improper operation of locksets and binding of bolts
in the strike. Check carefully the installation of the
frame prior to making hardware adjustments.
5
SDI 122-2015
Hinge Bind Against Rabbet

Normally, hinge bind is found between the door and rabbet. There are several ways of shimming which will
move the door in different directions. The following guidelines should be used in shim applications.
INCREASED GAP
CL HINGE
HINGE SHIM
BARREL
JAMB HINGE REINF.
1. A shim can be placed between the frame

hinge reinforcement and the hinge leaf. This
will move the door towards the strike jamb. NOT FLUSH
However, the hinge notch face gap will be
DOOR
increased and the hinge leaf surface will not
be flush with the rabbet surface. DETAIL #1
MOVES DOOR
TOWARDS
STRIKE JAMB
CL HINGE
BARREL HINGE JAMB
HINGE REINF.
NOT FLUSH
2. A shim can be placed between the door

DOOR
and the hinge leaf. This will also move the
INCREASED
GAP DETAIL #2 SHIM door towards the strike jamb. However, an
increased gap will be created by the shim
MOVES DOOR
and the hinge leaf surface will not be flush
TOWARDS with the backset surface on the door.
STRIKE JAMB
INCREASED GAP
CL HINGE SHIM
BARREL HINGE
JAMB
HINGE REINF.
NOT FLUSH
3. To minimize the gaps and the allow the
hinge leaf surfaces to remain flush with NOT FLUSH
the rabbet and backset surfaces, two
shims, each half the thickness of those DOOR
INCREASED GAP
used above, could be used. SHIM
DETAIL #3
6
SDI 122-2015
Hinge Bind Against Stops

Hinge bind against the frame stops is possible field condition. There are several ways of shimming which
will move the door in the desired direction. The following guideline should be used in shim application.
CL HINGE
BARREL HINGE SHIM B
JAMB
HINGE REINF.
Adjustment of Clearance Between NOT FLUSH

the Door and the Frame May be NOT FLUSH
Accomplished by the Following:
1. Using Shim “A” only, door will be relocated

in direction of Arrow “X”. DOOR SHIM A
“X”
2. Using Shim “B” only, will move both door
Shims A and B
and centerline of hinge barrel in direction
of Arrow “X”.
3. Using both Shims “A” and “B” will relocate

the door in direction of Arrow “X” by a
greater amount than by using Shim “B”
alone. INCREASED GAP
4. Using Shim “C” only, door will be CL HINGE

SHIM D
BARREL HINGE
relocated in direction of Arrow “Y”. JAMB
HINGE
REINF.
5. Using Shim “D” only, both door and
centerline of hinge barrel will move in
direction of Arrow “Y”.
6. Using both Shims “C” and “D” will relocate

the door in direction of Arrow “Y” by a INCREASED GAP
DOOR SHIM C
greater amount than by using either “C”
or “D” alone. The centerline of hinge
barrel will be relocated the same as by
using Shim “D” alone. Shims C and D
“Y”
7
SDI 122-2015
Twisted Door
Normal installation results in the plane of the door face being parallel
with the plane of the frame face. If the frame is square and plumb, all
face surfaces of the frame will be in the same plane. A twisted door
will “break through” the frame’s face plane surface. BE SURE the
frame is square and plumb. If it is not, the problem is probably with
the frame installation and NOT the door. DOOR
JAMB
FACE OF DOOR
SHOULD BE
PARALLEL WITH
IMAGINARY
PLANE ACROSS
FACES OF FRAME
JAMB
IMAGINARY PLANE
ACROSS FACES
OF FRAMES
Door “Break-Through” or “Twist” can be found

in different locations on different doors. Usually
it is found diagonally between opposite lower
and upper corners.
8
SDI 122-2015
Twisted Door Adjustments

When required, it is possible to “spring” the door back to (or much closer to) its ideal position of being
parallel with the plane across the faces of the frame. This can usually be done with the door remaining in
the frame. A piece of wood blocking must be placed between the door and frame. Pressure is then applied
at the twisted area to “spring” the door. However, caution should be exercised on drywall installations
since the frame could possibly work lose from the wall, particularly with slip-on drywall type frames.
Twisted at Top
When the top lock area of a door is “breaking-
through” the plane, place a wood block on floor,
between door and frame as shown. Apply pressure
to the top lock area as shown to “spring” door back
into position. Remove wood block, close door and
check condition. Repeat if necessary.
WOOD
BLOCK
WOOD
BLOCK
Twisted at Bottom
When the bottom lock area of door is “breaking-
through” the plane, place a wood block between
frame head and door as shown. Apply pressure to
the bottom lock area as shown to “spring” door back
into position. Remove wood, close door and check
condition. Repeat if necessary.
9
SDI 122-2015
Twisted Door Adjustments (continued)

An alternate method can also be used which will allow the door to remain in the opening. This method
might be appropriate in drywall installations as previously mentioned. Although the example shown
deflects the top half of the door, this method could be used on the bottom half of the door as well.
SOLID WOOD
SPACER ¾″
PULL DOWN
TOWARD TUBING
CLAMP WITH CLAMP
LOCATE CLAMP
CLAMP JUST BELOW
POINT OF "BOW"
SOLID WOOD
CLAMP SPACER ¾″
TUBING SUCH AS
2″ × 2″ × ¼″
WALL STRUCTURE
DOOR
10
SDI 122-2015
Twisted Frame
Wall conditions and anchoring methods can cause the frame to be “twisted” in the opening. The two jamb
(hinge and strike) faces are not in the same plane as discussed in the twisted door section. This can be
checked by using a level and/or plumb bob. Frames do not have adjustments when it comes to “twist”.
The “twist” condition is generally caused by the wall conditions. The frame jamb faces are prevented from
being set in the same plane because the walls are out of plane to begin with.
The options available to correct this problem depend, to a large extent, on the wall construction.
LEVEL
JAMB
90°
90°
CHECK WITH
LEVEL
This jamb is not level. Using a

level or plumb bob will show
which way the bottom of the
frame must move.
PLUMB BOB
11
SDI 122-2015
Frame Set out of Square

Proper frame installation cannot be overemphasized. In the
majority of wall constructions, (“slip-on” drywall type frames
being the major exception) “quick” or “easy” field fixes are limited.
Improperly set frames that are drastically out of square will cause
severe door and hardware problems. These types of situations
would require extensive field repair and may result in having to
remove frames from walls.
If the “out of square” condition is slight, some adjustment can be
made by shimming and/or adjusting anchors, particularly if the
frame being worked on is a slip-on drywall type.
The most versatile frame to work with in correcting these types Corner Clip
of conditions is the “slip-on” drywall frame. The manufacturers’
instructions should be referenced, but generally most “slip-on” Header to jamb connection
drywall frames have a sill anchor at the bottom of the jamb and a
compression anchor between the top hinge and the header. Also,
most jambs have corner clips that have a hole to accept a screw.
The corner clip and hole align with a hole in the header. The
adjustment of slip-on drywall frames can be made using these
anchors or corner clips.
90° 90°
Compression Anchor
(Cut-away view)
PROPERLY SET FRAME

All corners are 90º. The dimension taken
at Point “A” is equal to the dimension
checked at Point “B”. Both hinge and strike
jambs are plumb and level.
Sill Anchors
Snap-in type or screw type
12
SDI 122-2015
Frame Set out of Square (continued)

The following examples illustrate how a frame can be set out of square.
85° 95° IMPROPERLY SET FRAME (A)

One corner is greater than 90º and one corner is less than 90º.
The miters do not properly align with one another and “gaps” are
created in the miters which are opposites of one another. The
A dimension taken at point “A” would remain the same when checked
at point “B” if the 90º corners are out of square an equal number of
degrees.
This condition can be corrected by adjusting the compression
anchors in and/or out of each jamb as required. Loosen the corner
clip screws if the frame is so equipped before making adjustments;
B retighten when finished. The compression anchors must be
adjusted (turned) in opposite directions to allow the jambs to move.
For the illustration shown, the strike jamb compression anchor
screw must be turned counterclockwise to retract the compression
anchor and give room for the frame to be adjusted back into
position using the hinge jamb compression anchor. The hinge jamb
compression anchor screw is then turned clockwise to advance
the anchor and push the frame towards the room made at the
strike jamb. The frame should be brought into square with
the header and the hinge jamb compression anchor. Once
this is done, the strike jamb compression anchor screw can
be turned clockwise, advancing the anchor snug against the
stud. The corner slip screws should then be retightened.
13
SDI 122-2015
IMPROPERLY SET FRAME (B)

85° 85°
The corners are both greater than or less than 90º. The
miters do not properly align with one another. When the
corner is less than 90º the miter will have a gap which
increases as it goes towards the return. When the corner
is greater than 90º the miter will have a gap, which
A increases as it goes towards the rabbet. Dimensions taken
at point “A” and “B” will not be equal. This condition will
always result in dimension “B” being either greater than or
less than the nominal opening dimension which would be
obtained if checked between jambs along the header.
95° 95°
Jambs Toed In at Sill

A
To correct this condition, the sill anchors must be

loosened to allow the bottom of each jamb to be
moved in and/or out. In the case of the snap-in
type sill anchor, the baseboard trim might have to B
be removed to gain access to the anchors. This
type of anchor is generally used because it can be
hidden by covering it with the baseboard trim.
If the jambs are toed in at the sills, the
compression anchors might have to be retracted
slightly so the sill (base) of the jambs can be
pushed out. The jambs should be plumbed,
squared with the header and leveled as they are
pushed out into their proper position. The sill
Jambs Toed Out at Sill
anchors should be reset, the compression anchors
adjusted and retightened. The baseboard trim should be reattached to the
wall if it had been removed.
A similar procedure should be used if the jambs are toed out at the sills.
The sill (base) of the jambs should be pushed in towards the opening.
The jambs should be plumbed, squared with the header and leveled as
they are pushed into their proper position. The sill anchors should be
reset, the compression anchors adjusted (extended) and retightened. The
baseboard trim should be reattached to the wall if it had been removed.
14
SDI 122-2015
IMPROPERLY SET FRAME (C) 90° 95°

One corner is properly set at 90º while the other
corner is greater or less than 90º. The dimension
taken at point “A” will constantly change when
checked at various points going towards point “B.”
The corner miter will not properly align between A
the header and jamb which is not set at 90º

The jamb which is not 90º to the header must be
moved. To correct this condition, the sill anchor
must be loosened to allow the bottom of the jamb
B
to be moved in or out as required. In the case of
the snap-in type sill anchor, the baseboard trim
may have to be removed to gain access to the
anchor. This type of anchor is generally used
because it can be hidden by covering it with the
baseboard trim.
One Jamb Toed Out
85° 90°
If the jamb is toed in at the sill, the compression

A anchor may have to be retracted slightly so the sill
(base) of the jamb can be pushed out. The jamb
should be plumbed, squared with the header and
leveled as it is being pushed out into its proper
position. The sill anchor should be reset, the
compression anchor adjusted and retightened.
The baseboard trim should be reattached to the
wall if it had been removed.
B
A similar procedure should be used when the
jamb is toed out at the sill. The sill (base) of the
jamb should be pushed in towards the opening.
The jamb should be plumbed, squared with
the header and leveled as it is pushed into its
proper position. The sill anchor should be reset,
the compression anchor adjusted (fastened)
One Jamb Toed In and retightened. The baseboard trim should be
reattached to the wall if it had been removed.
15
SDI 122-2015
Frame with Rabbets Toed In or Out

The importance of proper initial frame installation is evident in this condition. In the majority of wall
constructions, except for the “slip-on” drywall type frames, “quick,” “easy” field fixes are limited. Improperly
set frames which have the rabbets drastically toed in or out would require extensive field repair and in
most cases require that the wall be entered to gain access to frame anchoring.
The toed in or out condition is worse near the floor. The header prevents the upper portion of the jambs
from toeing in or out but as you move away from the header towards the floor, the jambs have greater
potential to be toed in our out during installation.
The only frame with this condition which can be corrected with little difficulty is the “slip-on” drywall frame.
Since the “slip-on” drywall frame uses only compression anchors near the head and sill anchors near the
bottom of the jambs, this condition is easily corrected.
AMOUNT OF PLANE OF WALL

TOE OUT 90°
Note that the rabbet surfaces are
not 90° to the plane of the wall. This
can be checked by placing a straight
edge across the face of both jambs.
The straight edge should set flat
across both faces at the same time.
90° If the jambs are twisted, a “gap” will
AMOUNT OF PLANE OF WALL
TOE OUT be created as shown in the figure to
PARALLEL TO PLANE OF WALL the left.
Typical toed-in or out condition
The figures to the right show the two typical

types of sill anchors used on the “slip-on”
drywall frame. A
“A” shows an anchor which will be covered
up by the baseboard trim. To gain access to
this anchor the baseboard trim must first be
removed. Next, the nails or screws holding
the anchors to the wall must be removed.
This will loosen the jamb and allow it to be
squared in the opening.
“B” illustrates a screw going through the
face of the frame into the wall. This holds
the sill of the frame in position. This screw
is exposed and is readily accessible.
Removing the screw will loosen the jamb B
and allow it to be “squared-up” in the
opening. If both jambs are toed in/out, they
both should be “squared-up.” This can be
checked by taking measurements as shown
below. Both the “A” and “B” dimensions will be the same when the frames are properly set. However, the
frame jambs must be plumb, level, and square with the head of the frame.
16
SDI 122-2015
Frame with Rabbets Toed In or Out (continued)
DIM. “A”
DIM. “B”
If both jambs are toed in/out, they both should be “squared-up.” This can be checked by taking
measurements as shown above. Both the “A” and “B” dimensions will be the same when the frames are
properly set.
The below figure shows a condition which can give the impression that the frame is properly installed.
Both dimensions “A” and “B” will be equal but the frame will not be square in the opening. Both jambs can
be twisted to create a parallelogram. This can be checked by placing a straight edge across the face of
both jambs (the straight edge is represented by the dotted line shown below. The straight edge should set
flat across both faces at the same time. If the jambs are twisted, a “gap” will be created as shown in the
illustration. The “gaps” will be to the same side if a parallelogram was created. The gaps could also be to
opposite sides as shown in the Typical Toed In or Out Condition figure on the previous page.
This condition can be corrected as outlined for the other “toe out” or “toe in” examples.
DIM. “A”
GAP
GAP
90°
90°
DIM. “B”
PARALLEL TO
PLANE OF WALL
17
SDI 122-2015
Silencers
Some manufacturers provide a silencer hole in the frame stop to accept a push-in silencer. A “stick-on”
silencer is also available for application to frames without the silencer hole. The silencer acts as a “rubber
bumper” which evenly holds the door off the stop at a constant distance. If the door is held off of the stop
rather than being allowed to move slightly towards the stop, the latch tube will fit tighter into the strike.
Three silencers are placed on the strike jamb, one toward the top of the jamb (nearer the header) and one
toward the bottom of the jamb (nearer the sill) and the third near the strike preparation.
18
SDI 122-2015
Lock Fits Loose on Strike

This condition cannot be caused by an improperly set door and/or frame. If the lockset on the door was
not properly aligned with the strike on the frame, interference would occur or the latch bolt would bind in
the strike. Since this is not the case; the cause is something other than improper installation. The following
should be checked:
PROPER STRIKE
Is the proper strike plate attached to the frame?
RIM EXIT DEVICES

An adjustable strike plate is provided. Is the strike
plate properly adjusted to prove positive and secure
latching?
19
SDI 122-2015
Lock Fits Too Tight in Strike

Proper installation of the door and frame are essential. If the door and frame are not properly aligned, the
latch bolt could bind in the strike. The following items should be checked:
IMPROPER CLEARANCE/DOOR SAG

For various conditions, refer to page 2.
HINGE BIND
For various conditions of hinge bind, refer to page 6.
TWISTED DOOR
For various conditions of twisted doors, refer to page 8.
TWISTED FRAMES
For various conditions of twisted frames, refer to page 11.
FRAME SET OUT OF SQUARE

For various conditions of frames set out of square,
refer to page 12.
PROPER STRIKE
Is the proper strike plate attached to the frame?
The previously mentioned items

should be checked and any problems
corrected. If the latch continues to
LE
FI tightly engage the strike, additional
clearance can be created by filing the
strike or bending the latch bolt lip as
shown. However, this should only be
done as a final option.
D
BEN
20
SDI 122-2015
Lockset Off Location on Door or

Strike Off Location in Frame in Wall
Minor location adjustments usually can be accomplished by altering the strike plate. The strike plate
alteration would “extend” the opening to allow the latch tube to properly engage the strike. This is similar
to the section “Lock Fits Too Tight in Strike” except that the amount of material removed from the strike is
greater. This could compensate for minor mislocation of the strike plate on the frame and/or location of the
lockset on the door. These general steps should be followed for modifying the strike plate.
MARK AREA
TO BE REMOVED
• Mark the area on the strike plate which

must be removed.
• Remove strike plate from frame.
• Center punch corners of area to be re-
moved and drill a 1/8″ diameter hole in
each corner.
• Use a saber saw and cut from the exist-
ing opening up to the 1/8″ diameter holes.
The remaining material between the two
1/8″ holes should be filed away.
• Dress off all rough edges and corners
with a file. This must be done since any
irregular edges or edges with burrs could
cause the latch tube to “drag” or “hang up” DRILL HOLES
in the strike plate.
• Reassemble strike plate to frame and
check alignment with lockset on door as
well as latch tube function in and out of
strike plate.
CUT
21
SDI 122-2015
Miter Not Closed on Frame

The major cause of miters not properly lining up and “closing” is incorrect installation. The effects of
improper installation on miter seams are covered under the previous section of “Frame Set Out of Square.”
This section should be referenced for detailed explanations of conditions which could occur, and solutions
for correcting the problems.
This condition could also be caused by conditions as explained in the “Frame Loose on Drywall” section—
figures on page 28.
22
SDI 122-2015
Clearance at Bottom of Door Too Small

The available options for correcting this problem are limited. Frames which are permanently anchored to
the wall construction (such as masonry or steel stud) leave few alternatives. The only available “fix” is to
trim the bottom of the door, if the door’s construction will permit trimming. As shown in the figure below,
the nominal “sill clearance” should be ¾ of an inch. The sill clearance is the dimension from the bottom of
the door to the bottom of the frame jambs, and ¾″ is a standard industry dimension.
The frame jambs should be set at
floor level which then results in ¾
of an inch between the bottom of
the door and floor.
The 3/4″ also provides enough
room to allow the installation of
a “raised sill” which is a type of
flat threshold. If a raised sill is
used, the ¾ inch clearance is
decreased.
Before any alterations are made DIM. “B” DIM. “A”
the door height dimensions
should be checked.
The door height is determined
by taking a measurement
represented by dimension “A” in
the figure. If the door height is
“oversize” the clearance at the
bottom will be too small.
¾″ FLOOR
The frame jamb height (which LINE
is the same as the opening
height) is determined by taking
a measurement represented by
dimension “B”. If the jamb height is
“undersize,” the clearance at the bottom will be too small.
The bottom of the frame jambs should be set “on” the floor not “in” the floor. In some special cases the
jambs can be set “in” the floor but this requires special design consideration and adjustments in door
height and jamb heights. If this was not compensated for in the designed heights, the clearance at the
bottom could be too small.
By taking these basic dimensions, you can confirm what element of the opening is in error. If trimming the
bottom of the door is considered, you must make sure that the door’s design will allow such a modification
to be made. It is best to contact the distributor or the manufacturer to determine if and how much the
door can be trimmed. These types of trimming modifications can be relatively simple or more extensive
depending on door design.
23
SDI 122-2015
Frame and Door Hinge Misalignment

Frame and door hinge misalignment can cause a variety of problems. When misalignment occurs, either
the door’s hinge locations or frame’s hinge locations are slightly off. This can apply to retrofitting existing
openings where either the door or frame is being replaced, but not both. When new doors and frames are
provided from a single manufacturer, this problem does not exist.
The example shown on the following page reflects the dropping of the hinge leaf which attaches to the
door from its relationship to the hinge leaf on the frame. However, by removing material from the opposite
end of the knuckles, the door hinge leaf could be raised as well. The frame hinge leaf can also be
relocated in similar fashion.
HINGE LEAF ON FRAME
MISALIGNMENT
HINGE LEAF ON DOOR – MUST MOVE DOWN
PROPER
CLEARANCE
24
SDI 122-2015
Frame and Door Hinge Misalignment (continued)

Hinge leaf Hinge leaf on door
on frame (must move down)
Since the hinge leaf on the door

must move down, material must be
taken off of the knuckles as shown.
Mark the amount to be removed
equal to the misalignment.
Hinge pin
Hinge leaf on frame Hinge leaf on door
Disassemble hinge.
Remove material on
knuckles equal to the
misalignment.
Hinge leaf Hinge leaf

on frame on door
Reassemble hinge leaves and insert hinge pin.

Note: Gaps will now exist between the
knuckles in the areas shown. Proper thickness
and diameter flat washers can be placed in
these areas during hinge assembly.
25
SDI 122-2015
Frame Loose on Drywall

Frame manufacturers closely control the dimensions to which their frames are manufactured. Since
automated equipment is used these dimensions are easily repeated from piece to piece. The majority of
cases where frames are loose on drywall will reveal that the overall wall thickness has not been properly
maintained. Wall thickness conditions can vary from undersize to oversize. The thickness should be
checked, if possible, to verify the wall’s compliance with the job specification.
Frames installed in drywall walls can use two different anchoring methods:
WELDED/SNAP-IN STEEL, OR WOOD STUD ANCHORS

Some frames use welded or snapped-in steel or wood stud anchors. These frames are installed prior to
the drywall material being attached to the studs. The drywall can either be “butted-up” against the return
of the frame or be “tucked in” behind the return of the frame. Only in the installation where the drywall is
“tucked in” behind the return can there be a condition where the frame is loose on the drywall. This gap
could be uniform along the entire length (height) of the jamb or could be only in certain areas. Since the
frame cannot be removed, the only available options are to caulk the gap or cover it with trim.
Drywall “tucked in”

behind frame return.
Caulking
or trim
GAP
26
SDI 122-2015
Frame Loose on Drywall (continued)
DRYWALL FRAMES WITH COMPRESSION ANCHORS

These frames are intended to be installed after the wall construction is complete. The anchoring methods
that this type of frame uses allows the removal of the frame if so desired. The manufacturers’ installation
instructions should be followed anytime the frame is removed and reinstalled. Three conditions could exist
for drywall slip-on frames which are “loose on the wall.”
1) The first condition is a uniform gap along the entire length (height) of the frame jambs. The frame
should be removed from the opening and the wall thickness checked at numerous places around the
opening. These measurements should be compared to the job specifications. If the wall thickness is
undersize, two options are available.
a) If the gap is relatively small, the use of caulking or trim can be considered to cover the gap when
the frame is installed.
b) If the gap is larger, the use of “spacers” can offset the lacking wall thickness. The use of spacers
requires that the frame be removed from the opening, the spacer(s) attached, and the frame
reinstalled. The spacers can be used on either one or both of the frame returns which would
result in spacers on either one side or both sides of the wall. Spacers are available from the frame
manufacturer.
SPACERS ARE NOT TO BE USED ON LABELED FIRE DOOR FRAMES.
Use spacer on Use spacer on

one return both returns
Spacer
Check wall thickness
27
SDI 122-2015
Frame Loose On Drywall (continued)
2) The second condition would be a gap

that changes along the length (height)
of the jamb. This condition is generally
found in steel stud construction and
results in “over thick” walls in the upper
corners of the opening, refer to Figure
5. This is usually a direct result of how
the steel stud headers were attached
to the vertical steel studs to form the
opening. When the wall is oversize
(in this area) it will force the header
and jamb miters to spread apart and
actually open up the throat dimensions
to accept the oversize wall. This will
cause the corners of the frame to be
extremely tight on the wall and as you
progress down the jamb, a gap will
begin to develop and then gradually
disappear closer to the floor, see figure Areas where wall thickness
on following page. may be over-thick in steel-
stud construction.
IZE
E RS
V
LLO
WA
HEAD
JAMB
Frame spreads apart with oversize wall.
28
SDI 122-2015
Frame Loose on Drywall (continued)

HEAD
This condition should be reported to the
appropriate jobsite personnel. The condition
can be corrected by putting a bearing plate on
each side of the corner and compressing the
internal steel studs with a clamp. However, the
responsibility for correcting this condition belongs HT
TIG
to the sub-contractor responsible for the actual wall JAMB
construction. AS
E
C RE
P IN
GA
E
AS
C RE
P IN
GA
SE
EA
E CR
PD
GA
E
AS
C RE
P DE
GA
CLAMP
FIT
ER
OP
PR
Gap produced by oversized wall.
Correct oversized wall

condition by compressing
internal steel studs.
3) The third condition is different from the first two which address the “fit” of the frame over the wall
thickness. The cause of this condition is compression anchors which have not been tightened. The
drywall frame would then be loose across the width of the opening and move from side to side against
the rough opening.
The frame should be plumbed, squared and secured in the opening by properly adjusting the
compression anchors following the manufacturers’ instructions.
29
SDI 122-2015
Glazed Window Units

Hollow metal borrowed light, transom, and combination sidelight frames are an excellent choice for
exterior openings due to their design flexibility, thermal performance, and security. These types of frames
are not factory sealed to prevent water infiltration; the contractor/installer must seal all joints that are
exposed to the elements after the frame assembly is installed.
Whenever possible it is strongly recommended that the glass and glazing be installed on the exterior
rabbet of the frame. This will act as a deterrent to water penetration.
Manufacturers cannot control the workmanship associated with the installation of these types of frames,
therefore, this work must be specified in the installation/glazing/caulking section of specifications.
30
SDI 122-2015
Label Missing from Fire-Rated Frame

Like doors, fire-rated frames are an important element of compliance with building codes and fire
protection standards. Consequently, proper control of the labels which are attached to the frame is top
priority for the manufacturer, code official and labeling agency. Once the product is in the field, whether it
is installed or not, no one, including the manufacturer is permitted to attach labels unless a representative
of the manufacturer’s labeling agency has inspected the product for compliance with the manufacturer’s
procedures. Only authorized individuals can be in possession of and attach labels to fire rated products in
the field.
All labels on fire rated frames are located on the hinge jamb between the top and middle hinge (see figure
below). It should be noted that some frames have an embossed label, rather than a surface-attached
label. The embossed label is stamped into the frame rabbet and can be painted over.
If the label or embossment is not present, the frame distributor should be contacted.
TOP HINGE
LABEL
Special Notes:
• Borrowed light frames may have MIDDLE HINGE
labels applied to soffit of frame
due to glass and glazing bead
location.
• Frames incorporating continu-
ous hinges may have labels
applied to soffit or frame head.
• See manufacturer’s procedures.
31
SDI 122-2015
Label Missing from Fire-Rated Door

Fire-rated doors are an important element of compliance with building codes and fire protection standards.
Consequently, proper control of the labels is top priority for the manufacturer, code official and labeling
agency. (The manufacturer must account for every label used and the label can only be applied at the
manufacturer’s facility or at an authorized labeling distributor of the manufacturer.) Once the product is
in the field, whether it’s installed or not, no one, including the manufacturer is permitted to attach labels
unless a representative of the manufacturer’s labeling agency has inspected the product for compliance
with the manufacturer’s labeling procedures. Only authorized individuals may be in possession of and
attach labels to fire rated products in the field.
Labels on fire-rated doors are located in one of two places, either between the top and middle hinge, or on
the top channel (see figure). Be sure you are looking for the label in the correct location.
If the label is not present, the door distributor should be contacted.
TOP CHANNEL
Special Notes:
TOP HINGE
• Labeled doors incorporating con-
tinuous hinges may have labels
placed on the top channel of the
door. Check with the individual
LABEL manufacturer to determine location
of label.
• Labeled hollow metal transom
panels may need to be removed to
verify labeling if fully enclosed by
a fixed hollow metal frame.
MIDDLE HINGE • See manufacturer’s procedures.
BOTTOM HINGE
32
SDI 122-2015
Paint Problems
PAINT PEELING TO BARE METAL

Two conditions exist that must be considered when evaluating paint peeling to bare metal.
1. Prime Paint Only

If the product is only prime painted, and peeling has occurred, then poor adhesion between the primer
and bare metal has occurred. This can usually be attributed to inadequate surface preparation before
prime painting. The bare metal must be adequately prepared to ensure good prime paint adhesion.
The door should be completely sanded, washed with solvent and re-primed. The sanding and washing
operations provide an adequate surface to assure good primer adhesion.
2. Prime Paint and Top (Finish) Coat

The failure could be caused by either poor surface preparation before prime painting or the use of a non-
compatible finish paint that has reacted with the primer and lifted all paint from bare metal. In either case
the corrective measure would be the same. The door should be completely sanded and washed with an
appropriate solvent. The door should then be re-primed. Lightly sand the prime coat, wipe and finish-paint
with a compatible top coat.
Whenever the door is being prepared for top or finish-coat painting the surface should be cleaned. Use the
same solvent that will be used to thin the topcoat paint and thoroughly clean all surfaces to be painted.
PAINT IN TAPPED HOLES

Both hollow metal doors and frames have various holes that are drilled and tapped. These holes are in
various components such as reinforcements. All of the components are brought together as an assembly
prior to the painting operation.
There are a variety of painting methods manufacturers can use. Some of these methods can result in
paint build-up in the tapped holes of the reinforcements. This build-up can make installation of screws
difficult. The build-up should be removed to make screw installation easier and assure that the screws are
properly seated.
The best method of cleaning the tapped holes is to use an actual thread tap which matches the screw
thread. The tap will easily cut though and clean paint build-up and by running it in and out of the hole. If
the build-up is not as great and extra screws are available (or can be obtained) a screw can be run in and
out of the hole to clean minor build-up prior to final screw installation.
33
SDI 122-2015
Water Stain Damage

Water stain damage is a direct result of improper storage. If the product is still in prime paint (no finish
coat has been applied) the condition is easily detectable as follows:
• Initially, the water stain appears as a discoloration or variance in sheen or
gloss in the primer. Damaged areas will look and possibly feel different from
the rest of the product.
• If the water stain has existed for a considerable length of time and was caused
by large amounts of water, rust will start to appear through the discolored areas.
If the product has had a finish coat of paint applied, water stain damage can cause failure of the finish
coat as well:
• Water stain damage can be detected by random areas of finish paint failure
on the door as well as the appearance of uniform rust development on those
areas. In some cases the finish paint will show good adhesion in water dam-
aged areas but will also show a uniform layer of rust developing through the
finish paint.
To correct water stain damage, use the following guidelines:

• For products that are prime painted only, the affected areas should be ad-
equately sanded. If necessary, the area should be sanded to bare metal. The
entire door/frame surface should then be lightly sanded and “feathered” into
any heavily sanded areas. The entire surface should then be re-prime painted.
• For products that are finish painted, the affected areas should be adequately
sanded. If necessary the area should be sanded to bare metal. The entire
remaining finish-painted area should then be lightly sanded and “feathered”
into any heavily sanded areas. If bare metal is showing, these areas should
be re-prime painted and lightly sanded to “feather” into the lightly sanded
finish-painted areas. The product should then be re-finish painted.
• When the door is being prepared for top or finish coat painting, the surface
should first be cleaned. Use the same solvent that will be used to thin the
topcoat paint and thoroughly clean all surfaces to be painted.
34
SDI 122-2015
Thermal Bow
Installers need to be aware of a condition known as Thermal Bow. Thermal Bow is a temporary condition
which may occur in metal doors due to the inside-outside temperature differential. This is more common
when the direct rays of the sun are on a door surface. This condition is temporary, and to a great extent
depends on the door color, door construction, length of exposure, temperature, etc. This condition can
often be alleviated by painting the exposed surface a light color. Thermal bow can occur in reverse under
extremely cold conditions. Typical symptoms of thermal bow are hardware latching difficulty and door
clearance issues.
35
MEMBERS OF THE
Ceco
Specifications An ASSA ABLOY Door Group Company
9159 Telecom Drive
ANSI/SDI A250.6 Recommended Practice for Hardware Reinforcings on Standard Milan, TN 38358-3425
Steel Doors and Frames (731) 686-8345
www.cecodoor.com
Curries
SDI-108 Recommended Selection & Usage Guide for Standard Steel Doors An ASSA ABLOY Door Group Company
1502 12th Street
SDI-118 Basic Fire Door, Fire Door Frame, Transom/Sidelight Frame, and P.O. Box 1648
Window Frame Requirements Mason City, IA 50402-1648
SDI-128 Guidelines for Acoustical Performance of Standard Steel Doors & (641) 423-1334
www.curries.com
Frames
Deansteel Manufacturing Co.
SDI-129 Hinge & Strike Spacing 931 S. Flores Street
Test Procedures (210) 226-8271
www.deansteel.com
ANSI/SDI A250.3 Test Procedure & Acceptance Criteria for Factory Applied Finish
Coatings for Steel Doors & Frames 7980 Redwood Avenue
ANSI/SDI A250.4 Test Procedure & Acceptance Criteria for Physical Endurance for Fontana, CA 92336-1638
Steel Doors, Frames and Frame Anchors (909) 770-5700
www.doorcomponents.com
ANSI/SDI A250.10 Test Procedure & Acceptance Criteria for Prime Painted Steel HOLLOW METAL XPRESS
Surfaces for Steel Doors & Frames 602 S. 65th Avenue
ANSI/SDI A250.13 Testing and Rating of Severe Windstorm Resistant Components Phoenix, AZ 85043
(623) 936-7000
www.HMXpress.com
(Not applicable for FEMA 320/361 or ICC-500 Shelters)
Mesker Door, LLc
SDI-113 Standard Practice for Determining the Steady State Thermal 3440 Stanwood Boulevard
Transmittance of Steel Door & Frame Assemblies Huntsville, AL 35811-9021
(256) 851-6670
SDI-131 Accelerated Physical Endurance Test Procedure for Steel Doors, www.meskerdoor.com
Frames and Frame Anchors
MPI
Construction Details Corbin, KY 40701
(606) 523-0173
SDI-111 Recommended Details for Standard Details Steel Doors, Frames, 111 Kero Road
Carlstadt, NJ 07072
Accessories and Related Components
(201) 933-1900
SDI-122 Installation Troubleshooting Guide for Standard Steel Doors & www.pioneerindustries.com
155 Republic Drive
Miscellaneous Documents McKenzie, TN 38201-0580
(731) 352-3383
Frames SMP
An ASSA ABLOY Door Group Company
SDI-117 Manufacturing Tolerances for Standard Steel Doors & Frames
6089 Bristol Parkway, Suite 200
SDI-124 Maintenance of Standard Steel Doors & Frames Culver City, CA 90230
(310) 641-6690
SDI-127 Industry Alert Series (A-L) www.secmet.com
9017 Blue Ash Road
SDI-134 Nomenclature for Standard Steel Doors & Steel Frames
Cincinnati, OH 45242
(513) 745-6400

440.899.0010 • FAX 440.892.1404
7/7/2015
www.steeldoor.org
SDI
124 - 16
Maintenance
of
and Frames

SDI 124-16
Maintenance of
1 Introduction freely and smoothly without obstruction. Self latching

devices should always function freely and smoothly
This document is intended to serve as a general outline as the door swings into the closed position. Additional
of maintenance activities needed for standard steel force should not be needed to achieve latching. Silenc-
doors and frames. However, it should be noted that ers (mutes) should be replaced when latch operation
the door and frame are virtually maintenance free. is compromised by wear.
Maintenance will be, for the most part, associated
with the accessories and hardware attached to the Strike plate
door and frame.
The strike plate should be firmly attached to the frame
Maintenance of any product is important and necessary or inactive leaf of a pair of doors. Check for loose
to obtain the maximum benefits of product service and screws and/or other notable defects. Service or remove
longevity. Steel door and frame assemblies are not dif- and replace per the manufacturer’s instructions.
ferent. In fact, in some cases where the door and frame
assembly is used as a “fire rated” barrier or a “leakage Closing devices
rated” smoke barrier, proper maintenance is crucial.
Basic maintenance to ensure the proper functioning Check all closing devices for loose attaching screws,
of the assembly is imperative and well worth the effort linkage arm and pin wear, fluid leakage or other
to provide for human life safety. notable defects. Service the device or remove defec-
tive parts and replace following the manufacturer’s
2 Areas to be inspected recommendations. The primary and secondary closing
speed adjustments should also be set and maintained
The following items should be periodically checked. in accordance with the manufacturer’s recommenda-
The frequency with which these checks are performed tions. The device should allow the door to operate
must be established at the discretion of the building freely and smoothly throughout its entire swing range
owner, insurance company, labeling authority (as ap- and positively latch (if so equipped) or remain in the
plicable), and maintenance service. Since doors in closed position.
different areas of a building access service different
traffic, the frequency of periodic inspections would Flush bolts
occur respectively.
Check all flush bolts for loose attaching screws, rod
bolt adjustment and strike plate (on both door and
Hinges
frame if so equipped) attachment. Service the devices
Check all hinges for loose attaching screws, hinge or remove defective parts and replace following the
pin wear or other notable defects. Service the hinges manufacturer’s recommendations. The rod bolts should
or remove defective parts and replace per the manu- retract, extend and engage the strike or keeper hole
facturer’s recommendations. The door should always freely and smoothly for both manual and/or automatic
swing freely and smoothly without obstruction from flush bolts.
the opened to latched (when latching device is used)
position. Glass lights
The glazing material should be checked for cracks and/
Locksets, panic devices, fire exit hardware
or missing pieces of glazing. The glazing mounting
Check all locksets for loose attaching screws, latch frame should be checked to assure all attaching screws
wear or other notable defects. Service the lockset or (if used) are tight and the unit is securely attached to
remove defective parts and replace per the manufac- the door. Service the glass light or remove defective
turer’s recommendations. The door should always latch parts and replace by following the manufacturer’s rec-
1
SDI 124-16
ommendations. Also be sure to use approved safety codes. These doors must not be obstructed in any
glass in appropriate applications/locations, or fire rated fashion preventing them from functioning as intended.
glass and glazing in fire doors, windows or lights.
Gasketing/weatherstripping
Door and frame finish
A visual and operational inspection is periodically
A general visual inspection of the door and frame finish necessary for gasketed or weatherstripped areas such
should be periodically conducted. Any excessive finish as perimeter seals, threshold seals, door bottoms,
defects should be repaired and repainted. Adequate etc. Inspect for signs of deterioration such as splitting,
protection is needed to help prevent the product from
cracking or deforming of flexible components. Install
rusting prematurely and shortening its service life.
replacement components as needed.
Unobstructed operation
Inspect operational integrity by the following
Fire rated and/or smoke control assemblies are speci- method:
fied and installed to meet “safety to life code require-
Gasketing should be positioned to create proper
ments.” It is imperative that these assemblies receive
regularly scheduled maintenance checks for all of the contact along the door’s entire perimeter. The test for
above items. Additionally, for the assembly to serve its proper contact is usually done with common paper.
purpose of stopping fire and/or smoke propagation it The paper should be firmly held in place by inserting
must function freely with the ability to positively latch it between the door and gasket and then closing the
in the closed position. Therefore, propping or block- door. If the paper is not firmly held in place, the seal is
ing these doors in an open position is in violation of inadequate. The paper test should be conducted along
intended use and purpose as established in building the entire perimeter.
Related Documents:
— NFPA 80 Standard for Fire Doors and Other Opening Protectives, Chapter 5
— SDI-122 Installation and Troubleshooting Guide for Standard Steel Doors and Frames
2
MEMBERS OF THE
Ceco
9159 Telecom Drive
www.cecodoor.com
Curries
1502 12th Street
www.curries.com
Frames
www.deansteel.com
(623) 936-7000
www.HMXpress.com
Mesker Door, LLc
(256) 851-6670
MPI
(606) 523-0173
Carlstadt, NJ 07072
(201) 933-1900
155 Republic Drive
(731) 352-3383
Frames SMP
(310) 641-6690
9017 Blue Ash Road
(513) 745-6400

440.899.0010 • FAX 440.892.1404
7/7/2015
www.steeldoor.org
SDI
Industry Alert 127A - 06 (Reaffirmed 2014)
End Closure Location

The steel door industry utilizes a variety of end closure designs in standard doors. The most common are flush type
end closures or inverted end closures. The inverted (legs upward) end closures in many cases may create a necessity
to reposition the mounting holes for regular arm closures or surface overhead stops/holders. To avoid interference
with the “web” of the top end closure channel, mounting screws must be slightly repositioned.
A similar (but less serious) situation could occur when channel-shaped closer reinforcements are inserted into flush
type end closures. The additional layers of material or the joint itself could cause "creeping" of the drill bit or tap.
Illustrated below is the consensus of the Steel Door Institute members showing the location of these channel condi-
tions on standard steel doors.
It is suggested that the hardware manufacturer and/or hardware consultant be contacted for resolution of such a conflict.
Top of Door Top of Door Top of Door Top of Door
⅝" to 13⁄16" ⅝" to 13⁄16" ⅝" to 13⁄16" ⅝" to 13⁄16"

End Closure End Closure End Closure End Closure
Reinf.
Plate
Flush End Closure Flush End Closure Inverted End Closure with Inverted End Closure with
With Insert Channel with Offset Channel Reinforcement Plate Reinforcement Channel
Refer to ANSI A250.8 for Material Thickness

SDI
Industry Alert 127B - 06 (Reaffirmed 2014)
Door Edge Cutouts

The ability to form a crisp aesthetic cutout in the edge of a steel door, especially in the vicinity of a bend line is directly
influenced by the steel thickness and the proximity of the cutout to the bend line. A cutout too close to the bend line
will result in a flare‑out of the cutout area due to unevenly distributed stress along the brake die or rollform rollers.
The following illustrations are intended to convey dimensional limitations of the hardware items to be mortised into
the edge of 1 3/4" thick standard steel doors.
Certain lock fronts, concealed hinges, strikes, or electrical devices do not comply with these limitations. The resulting
potential for inaccuracy or lack of asthetics is inherent in the manufacturing processes and is not to be considered
a defect.
Edge seam system

varies by manufacturer
(not shown).
Variable
Variable
Minimum distance Dimension is to

to hardware item is hardware item, not
nominally ¼" " to cutout in door.
minimum. 1 ¼ x.
m a
Minimum distance " " Minimum distance to

nominally 1.5x face 1¾ 1¾ cutout is nominally 3x
sheet thickness face sheet thickness
or 3⁄16" minimum.
Cutout Limits Cutout Limits
Cutout Around Corner Cutout On Edge

SDI
Industry Alert 127C - 06 (Reaffirmed 2014)
Frame Cutout Limits

The ability to form a crisp aesthetic cutout in steel frames, especially in the vicinity of a bend line is directly influenced
by the steel thickness and the proximity of the cutout to the bend line. A cutout too close to the bend line will result
in a flare‑out of the cutout area due to unevenly distributed stress along the brake die or rollform rollers.
The following illustration is intended to convey dimensional limitations of the hardware items to be mortised into the
face, rabbet or stop of steel frames. Certain concealed hinges, strikes, or electrical devices do not comply with these
limitations. The resulting potential for inaccuracy or lace of aesthetics is inherent in the manufacturing processes
and is not to be considered a defect.
Inside Outside
Backset
Bends Bends
Min. A B C D
Gage
Thickness Min. Min. Min. Min.
D 18 0.042" 5/64" 7/32" 5/64" 7/32"
A A
C 16 0.053" 3/32" 7/32" 3/32" 7/32"
14 0.067" 7/64" 7/32" 7/64" 7/32"

SDI
Industry Alert 127D - 06
Electric Strikes in Stud Walls
Steel or wood stud and drywall construction methods and frame anchorage could result in interference between the
stud and electric strike. Notching of the stud could result in compromising the stability of the frame.
Dependent on the dimensions of the strike, the cutouts may extend beyond the frame face or the returns, thus leav-
ing critical strike parts or wiring exposed.
Consideration should be given to specifying a strike suitably sized to fit the confines of a standard frame or specifying
alternate frame profiles to accommodate the strike.
2" 2"
Common Common
Standard Standard
Wallboard Wallboard
Wall Thickness
Wall Thickness
Area commonly Area commonly

required for strike required for strike
Door Door
Wallboard Wallboard
Commonly
Commonly ⅜" to ⅝"
⅜" to ⅝" Commonly 5⁄16" to ½"
Minimum per ½"
NFPA–80 Minimum per ½"
Varies with NFPA–80 Varies with manufacturer
manufacturer commonly 1" to 1-½"
Typical Frame Profile Slip-on Drywall Frame

SDI
Industry Alert 127E - 06 (Reaffirmed 2014)
Prime Painted Materials Alert

Prime Painted Doors, Frames, and Accessories (where applicable) shall comply with the acceptance criteria specified
in ANSI A250.10-1998 (R 2004). Doors and frames are cleaned and treated prior to painting to ensure maximum paint
adhesion. All exposed surfaces are then given a factory-applied coat of rust inhibiting “direct to metal” type primer.
The primer is then baked, air dried, or otherwise cured as appropriate for the primer.
This process is intended to protect the steel surfaces for a period of time under reasonable weather exposure condi-
tions. Factory applied primer coatings may be somewhat porous in order to accept finish coatings. The primer coating
may therefore be susceptible to the action of moisture or ambient moisture condensation during shipping or storage.
For example, transportation of materials in unprotected “open” trucks during inclement weather (rain or snow) or on
roadways where salt or other snow melting agents are used will deteriorate the primer. Extended exposure to such
conditions may result in rusted or water stained areas. ANSI A250.8-2003 (SDI-100) paragraph 4.1 presents Industry
recommended jobsite storage requirements.
Should the primer become scratched, abraded, rusted or stained, the affected areas may rust unless sanded and
reprimed with a suitable “direct to metal” primer containing rust inhibitors.
Prior to application of finish coats, the substrate shall be inspected by the Painting Contractor. All Architectural Specifica-
tion requirements along with all requirements of the paint manufacturer shall be followed. These will generally include
scuff sanding of the substrate to remove foreign materials, scratches or abrasions from construction processes, along
with any special or mandatory requirements for primer touch-up or additional primers required by the paint system.
MOST IMPORTANTLY, the field applied primer and finish paint “systems” must be designed for direct to metal ap-
plications and contain rust inhibiting properties.
IF COATING COMPATIBILITY IS AN ISSUE, contact the SDI Manufacturers or their local distributors who can provide
information or “sample” materials for the painting contractor’s use.

SDI
Industry Alert 127F - 10 (Reaffirmed 2014)
Butted Frames
Rough Opening Sizes
The variety of existing wall anchors available from SDI Members allow Standard Steel Door Frames to be a reliable
option for existing wall, structural steel wall framing or retrofit installations utilizing a butted to wall application. In order
to make the installation successful, careful consideration shall be given to all tolerances involved and that sufficient
clearance is figured to allow for them.
It has been “customary” to allow clearance around the frame perimeter when establishing rough opening sizes or
when figuring non-standard overall frame sizes. This clearance is necessary to compensate for any allowable manu-
facturing tolerances, installation tolerances, or substrate conditions. Tolerances and clearances are referenced both
pictorially and verbally in a number of Industry documents such as:
• SDI-110-09 (butted frames)
• SDI-111F-09 (existing wall anchors)
• SDI-117-09
• ANSI A250.8-2003 (R2008)
• ANSI/SDI A250.11-2001
• ANSI/NAAMM HMMA 840-07
• ANSI/NAAMM HMMA 841-07
Frames will “fit and function” if made to these dimensional tolerances and installed within tolerances. There is, how-
ever, relatively no assurance that the substrate (walls) will be of suitable size or alignment.
We therefore recommend that the rough openings for these cases be no less than 3/16″ larger on all 3 sides than the
“intended” overall frame size. (Example: 3070 standard frame = 3′-4 3/8″ x 7′-2 3/16″). The installer carries the responsibil-
ity for shimming and aligning as necessary. Gaps are normally sealed as part of the installation or caulking/painting
process. Architectural Specifications are to be consulted to determine the appropriate sealant material to be used at
fire door or smoke control frames.

SDI
Industry Alert 127G - 06 (Reaffirmed 2014)
Environmental Considerations
Relating to Factory Painted
There is an Industry need for a comprehensive revision of specifications, practices and procedures that will allow
compliance with existing and future regulations. The Member Companies of the Steel Door Institute have taken the
steps needed to eliminate from their primers, those elements identified by Regulatory Authorities as hazardous to
human health and the environment. This is not only a moral responsibility toward society, but also a survival respon-
sibility toward the business. The SDI encourages specification writers to look at these issues very carefully when
they specify coating requirements.
Federal and State Laws have regulated the management of hazardous waste so as to not pose a threat to the
environment or human health. Environmental Protection Agencies are very strict in regulations that affect coating
applications, by limiting the emission to the atmosphere of the amount of VOC (Volatile Organic Compound), which
has curtailed the use of solvent base paints.
Section 313 of the Emergency Planning and Community Right-to-Know Act (Title III) sets up the reporting require-
ments in the metal fabricating industry for all wastes containing any listed toxic chemical, which affects the use of
heavy metals (such as Zinc-Chromates) as rust inhibitors.

SDI
Industry Alert 127H - 10 (Reaffirmed 2014)
Water Penetration
Borrowed light assemblies, transom, sidelight, and combination transom sidelight frames are not factory sealed to
prevent water penetration. In situations where water penetration is a concern, the contractor must seal all joints that
are exposed to the elements after the frame assembly is installed.
Whenever possible, it is strongly recommended that glass and glazing be installed on the exterior rabbet of the frame
assembly. This will help act as a deterrent to water penetration.
The member companies of the hollow metal industry can not control the workmanship associated with the frame
installation; therefore, it is the responsibility of the installer to assure all steps are taken to prevent water penetration.
Exterior Rabbet Mounted Glazing (Recommended)
Vertical / Horizontal Mullion

Glazing Tape
Joint Sealant
Glass Stop Glass Stop
Setting Bead Exterior Setting Bead Exterior

Side Side
Caulk Screw Holes Caulk Screw Holes
Spacer Block
Sealant
Interior Rabbet Mounted Glazing

Vertical / Horizontal Mullion
Perimeter Bead
Glazing Glazing Perimeter Bead
Tape Tape
Exterior Exterior
Spacer Block Side Spacer Blocks Side
Joint Sealant
Glazing
Tape Perimeter Bead

SDI
Industry Alert 127 I - 10 (Reaffirmed 2014)
Grouting Frames in Drywall
Some Architectural Specifications require frames in stud and drywall partitions to be filled with grout for
sound deadening or to enhance structural integrity.
The STEEL DOOR INSTITUTE is opposed to this practice for the following reasons:
• In drywall construction, this moisture has two places to go. It can soak into the drywall, potentially
destroying its cohesive integrity and thus the ability to retain anchors or frame integrity, or it can
leach downward where it will cause premature rusting of anchors, screws, stud connections, bottom
of frames, etc.
• Grouting does not appreciably afford any additional structural rigidity to the frame. As an example,
slip-on drywall frames have passed fire and hose stream tests, cycle tests, and in some cases impact
tests without being grouted.
• If the intention is for sound deadening, SDI 128-97 (Section 3) should be consulted. In addition, the
same insulation as used between wall studs (generally lightly packed fiberglass) will serve as a sound
deadener without the potential for damage to the frame or wallboard.
It is therefore the opinion of the STEEL DOOR INSTITUTE that grouting should never be specified or
used for drywall construction.

SDI
Industry Alert 127J - 10
Back-Coating of Frames
Some Architectural Specifications require steel frames to be back-coated for corrosion protection or sound control.
A more modern back-coating material is automotive undercoating.
It is the recommendation of the STEEL DOOR INSTITUTE that this coating SHALL NOT be applied at the factory
or any location other than the jobsite. The coating never fully dries; leaving a dark residue that can be transferred to
the frame during transportation, storage, or handling prior to final installation.
ANSI A250.8-2003 (R2008) limits factory applied coatings to either factory prime finish (2.1.3) or factory-applied
finish paint (2.1.4).
For corrosion protection, ANSI A250.11-2001 paragraph 2.2 clearly states that “the contractor responsible for instal-
lation” applies corrosion resistant coatings only where specified for anti-freezing agents in plaster or mortar.
For sound control purposes, it is less damaging to the frame finish and more expedient for “the contractor responsible
for installation” to extend the insulation material used in the adjoining wall into the frame. This creates an unbroken
barrier to the passage of sound.

SDI
Industry Alert 127K - 09 (Reaffirmed 2014)
Improper Wedges
as Hold-Opens
It has come to the attention of the Steel Door Institute (SDI) that cleaning or maintenance personnel have been in-
correctly wedging doors to hold them open. This has been reported mainly in health care or hotel-motel installations
at patient rooms, utility rooms, sleeping rooms, and even stairways.
Instead of using rubber wedges at the bottom of doors or suitable hold-open mechanisms, wedges of various ma-
terials have been inserted between the hinge edge of the door and the hinge jamb. This practice puts an abnormal
stress on the hinge reinforcements, hinge knuckles, and attachment screws causing potential damage to any or all
of these components.
Damage, loosening, or failure resulting from this practice shall not be construed as a door, frame, or hardware
defect or warranty issue. The SDI strongly discourages the use of wedges in this manner or any methods for
holding doors open that will compromise the fire or life safety integrity of the openings.
The importance of unrestricted closing and latching of door openings in fire situations is further discussed in Sections
9 through 9.5 of SDI-118 “Basic Fire Door Requirements”.

SDI
Industry Alert 127L - 09 (Reaffirmed 2014)
Buyer Beware
Steel Doors with
Lead-Based Primer
Excessive lead paint in toys has been in the news a great deal lately. Just ask the toy industry about the far reaching
impact of selling products that don’t comply with federal regulations. U.S. manufacturers, contractors, and end us-
ers are aware of the regulations concerning the limitations of lead in paint. Although the toy industry may not have
knowingly violated these regulations, it is embroiled in this issue because it didn’t closely regulate the production of
these toys in a country where lead in paint is an accepted practice. United States industries need to comply with ap-
plicable regulations for all products that they produce, including all components and assemblies that are outsourced
to foreign manufacturers.
In light of the issues raised by the toy industry example and others, the Steel Door Institute felt it worthwhile to in-
vestigate the lead content of paint contained on steel doors imported into the United States. The investigations were
conducted by independent laboratories on randomly selected doors taken from various regions throughout the United
States. The results showed that all the doors tested exceed the allowable lead content for paint used in residential
and other consumer products. To ensure consumer safety and, to protect the interests of its membership as well as
the industry as a whole, SDI believes it is important to bring attention to this issue.
Risks of Using Lead-Based Paint

In addition to the issues associated with non-compliance with the federal statutes and regulations, there are more
serious risks associated with manufacturing, importing, buying or selling products that contain lead-based paint.
There are significant physical risks associated with ingesting lead by breathing or swallowing lead dust, which can
affect workers during construction and installation as well as the ultimate consumers who may come into contact
with the surfaces. For example, standard practice for top coat painting steel doors and frames is to rough up the
primer on the face of the door with abrasive sheets to improve adhesion to the primer. This practice will release lead

dust that could be potentially inhaled by the painter or other workers in the general vicinity. In addition, painting
over lead-based paint with non-lead paint is not a long-term solution. Even though the lead-based paint may be
covered by non-lead paint, the lead-based paint may continue to loosen from the surface below and create lead
dust. The new paint may also partially mix with the lead-based paint, and lead dust will be released when the new
paint begins to deteriorate.
Restrictions on the Use of Lead-Based Paint

There are a number of statutory restrictions on the use of lead-based or lead containing paint in the United States.
The Residential Lead-Based Paint Hazard Reduction Act of 1992 (P.L. 102-550, October 28, 1992) incorporates the
definition of lead-based paint contained in Section 302(C) of the Lead-Based Paint Poisoning Prevention Act (42
U.S.C. 4831), which characterizes any paint that contains more than .5% by weight of lead as “lead-based paint.”
Together, these two statutes prohibit the use of any paint with excessive lead content in new residential structures,
and mandate strict disclosure requirements with respect to the lead content of paint in existing dwellings.
The lead content restrictions are even more stringent under the Consumer Product Safety Act, which reduces the
threshold for characterization as lead-containing paint to .06% by weight of the total non-volatile content of the
paint or the weight of the dried paint film, and prohibits the use of such paint in residences and consumer products.
This prohibition extends to any products that may be used by consumers following an initial sale, including those
contained in apartment buildings, schools, hospitals, hotels, parks and any other public places or areas where
consumers may have access to the painted surfaces. (Consumer Product Safety Act, 15 U.S.C. 2057, 2058; 16
C.F.R. 1303.)
Due to the significant potential risks and costs associated with those risks of importing and/or distributing doors
containing lead-based paint, the Steel Door Institute feels obligated to alert the industry to the issue and to urge
the general public to be aware of the products that they are associated with, so that they can monitor compliance
with all applicable laws.
The Steel Door Institute does not make any assertions or conclusions other than those specifically contained
herein, which are limited in scope and used for illustrative purposes only.
Black Mountain Door DOOR COMPONENTS INC. Pioneer Industries, Inc.

310 Flint Drive 7980 Redwood Avenue 171 South Newman Street
Mt. Sterling, KY 40353 Fontana, CA 92336-1638 Hackensack, NJ 07601
(859) 274-0411 (909) 770-5700 (201) 933-1900
www.blackmountaindoor.com www.doorcomponents.com www.pioneerindustries.com
Ceco Door HOLLOW METAL XPRESS Republic Doors & Frames

9159 Telecom Drive 602 S. 65th Avenue 155 Republic Drive
Milan, TN 38358 Phoenix, AZ 85043 McKenzie, TN 38201-0580
(731) 686-8345 623-936-7000 (731) 352-3383
www.cecodoor.com www.HMXpress.com www.republicdoor.com
Curries Mesker Door, Inc. Security Metal Products

P.O. Box 1648 3440 Stanwood Boulevard 5700 Hannum Avenue, Suite 250
Mason City, IA 50402-1648 Huntsville, AL 35811-9021 Culver City, CA 90230
(641) 423-1334 (256) 851-6670 (310) 641-6690
www.curries.com www.meskerdoor.com www.secmet.com
Deansteel Manufacturing Co. MPI Steelcraft

931 S. Flores Street 319 North Hills Road 9017 Blue Ash Road
San Antonio, TX 78204-1406 Corbin, KY 40701 Cincinnati, OH 45242
(210) 226-8271 (606) 523-0173 (513) 745-6400
www.deansteel.com www.metalproductsinc.com www.steelcraft.com

440/899-0010 • FAX 440/892-1404
www.steeldoor.org
MEMBERS OF THE
Ceco Door
Milan, TN 38358
Curries
www.deansteel.com
Test Procedures
(909) 770-5700
HOLLOW METAL XPRESS
623-936-7000
www.meskerdoor.com
Corbin, KY 40701
155 Republic Drive
www.secmet.com
9017 Blue Ash Road
(513) 745-6400

440.899.0010 • FAX 440.892.1404
12/4/2014
www.steeldoor.org
SDI
128 - 16
Guidelines for
Acoustical Performance
of Standard Steel Doors
and Frames

SDI 128-09
Guidelines for Acoustical Performance of

1 General 2 Testing
1.1 Scope 2.1 Test Specimen

This document shall provide guidelines for the speci- Unless otherwise specified, the test specimen shall
fying, installing, and adjusting of standard steel doors be a nominal 36" (914 mm) wide, by 84" (2133 mm)
and frames in applications where sound control is a high for single doors and 72" (1,829 mm wide, by
consideration. 84" (2133 mm) high for pairs of doors. All doors shall
be 1 3/4" (44 mm) in thickness. All doors shall be fully
1.2 Definitions
operable. A detailed description of the test assembly
1.2.1 Sound Transmission Class shall be included in the test report.
A single number rating that indicates the sound trans- Ratings derived from non-operable assemblies shall
mission loss over a defined range of frequencies of a only be used for experimental purposes and are not
door assembly between adjacent closed rooms, ab- part of this document.
breviated STC. Higher values equate to better sound
reduction performance. 2.2 Test Method
1.2.2 Outdoor-Indoor Transmission Class The door assemblies shall be tested in accordance
with ASTM E 90. The STC and OITC ratings shall
A single number rating used to compare door as-
be calculated in accordance with ASTM E 413 and
semblies when subjected to exterior sounds, such
E 1332, respectively. The latest editions of the stan-
as ground or air transportation noise, is abbreviated
dards shall be used in determining the STC and OITC
OITC.
ratings. Testing shall be performed at laboratories that
1.2.3 Sound transmission loss – TL are accredited under the National Voluntary Labora-
tory Accreditation Program (NVLAP)
The reduction in sound level at specific frequency lev-
els when sound passes through a door assembly. 2.3 Test Results and Report
1.2.4 Frequency The test report shall be prepared by the test laborato-
ry and shall contain the information identified in Sec-
The number of cycles per second of a sound wave,
tion 13 of ASTM E 90 or Section 8 of ASTM E 1425.
measured in units of Hertz and abbreviated Hz.
1.2.5 Decibel – dB
3 Design Criteria
A unit used to express the intensity of a sound wave,
equal to 20 times the common logarithm of the ratio of
3.1 Performance Considerations
the pressure produced by the sound wave to a refer-
ence pressure, usually 0.0002 microbar. The proper function of acoustical doors relies on a
combination of factors that are under the control of
1.2.6 Sound Control Door Assembly various firms, trades, specifiers, suppliers, and de-
An assembly consisting of a door, frame, hardware, signers. Without the cooperation of all concerned, the
threshold, and gasketing, capable of reducing the installed opening may not function as intended. Prop-
transmission of sound. er seal installation and adjustment are critical to the
2
SDI 128-09
performance of the opening. The installation guide- doors. A wall that moves or flexes each time the door
lines shall be provided by the manufacturer. is operated cannot ensure that the gasket alignment
will be maintained.
Consideration must be given to correctly specifying
the door capability for the project condition. Some The manufacturer’s literature should be consulted to
doors, although rated higher in overall STC or OITC determine the weight of acoustical doors; especially,
ratings may not perform as well as lower rated doors
those that have higher acoustical ratings.
at certain frequencies. The test reports should be re-
viewed to establish the best TL values at the frequen- 3.2 Field Testing
cies under consideration for a given project.
Results obtained from field-testing may vary from
Room design should create a full enclosure equal to those obtained under laboratory conditions. Atmo-
or greater than the door’s TL capabilities. For exam- spheric conditions, room volumes, wall type and de-
ple, walls that do not run full height to a similar rated
sign, sound diffusion, test equipment, etc. may affect
overhead structure will allow sound leakage through
the results obtained when testing in the field.
ceilings, louvers, pipe chases, access doors, etc.
Carpeting, although considered a good source of 3.3 Hardware Considerations

sound absorption, should not be used underneath Hardware should be specified giving special consid-
acoustical doors. Door bottom gaskets must com- eration to the fact that it will be used on acoustical
press against a solid object to affect a proper seal. doors. Any type of hardware that may be the source
Carpeting by its nature does not provide that type of
of sound leakage should be avoided. Since all acous-
surface.
tical doors depend on a tight perimeter seal, some
Walls, in addition to their STC rating, should be de- types of hardware will become difficult to operate due
signed to support the additional weight of acoustical to the compression required to seal the opening.
3
MEMBERS OF THE
Ceco
9159 Telecom Drive
www.cecodoor.com
Curries
1502 12th Street
www.curries.com
Frames
www.deansteel.com
(623) 936-7000
www.HMXpress.com
Mesker Door, LLc
(256) 851-6670
MPI
(606) 523-0173
Carlstadt, NJ 07072
(201) 933-1900
155 Republic Drive
(731) 352-3383
Frames SMP
(310) 641-6690
9017 Blue Ash Road
(513) 745-6400

440.899.0010 • FAX 440.892.1404
7/7/2015
www.steeldoor.org
SDI
129 - 14
Hinge and Strike

Spacing

SDI 129-14
Cautionary Statement
The hinge and strike spacings presented in this brochure are intended as a reference to inform the reader of the
standard locations used in the manufacture of steel doors and frames by SDI member companies for the opening
sizes shown.
The user must be aware that these spacings shall not be relied upon when retrofitting doors or frames to an exist-
ing installation. Field verification of hinge and strike spacings in this situation is necessary.
Dimensions listed are valid at the time of publication. However, manufacturers do periodically revise their hinge
and strike spacing, therefore, the SDI strongly recommends that individual manufacturers be contacted to verify
dimensions.
The Steel Door Institute and its member companies shall not be held liable for products manufactured using the
information published here.
1
SDI 129-14
Ceco Door
EC
L Note: Dimensions listed are valid at time of publication. However, manufacturers do
A periodically revise their hinge and strike spacing, therefore, the SDI strongly
Opening
Height D
recommends that individual manufacturers be contacted to verify dimensions.
Hinge
CL Spacing
Note: On 3 1/2″ hinge preparation for 1 3/8″ doors, the standard for 6′-8″ non-fire
rated frames is two (2) hinges.
B
Strike
CL
C
3 1/2″ x 3 1/2″
Hinge
Frame
3-1/2″ Hinge & Strike Comparison for 1-3/8″ Thick Doors
F A B C D E F G
6′-8″ 2 @ 29-15/16″
1/8
1/16
7′-0″ 40-5/16″ 10-3/8″ 2 @ 31-15/16″ 9-3/4″ 5/16″ 1/4″
G
7′-2″ 2 @ 32-15/16″
1 3/8
Door

A B C D E F G H J
6′-8″ 2 @ 31″
6′-10″ 2 @ 32″
4 1/2″ x 4 1/2″ 7′-0″ 2 @ 33″
Hinge Frame 7′-2″ 2 @ 34″
F 7′-4″ 2 @ 35″
7′-6″ 41-13/16″ 9″ 2 @ 36″ 9″ 5/16″ 1/4″ 1/8″ 1/16″
H
J
G
7′-8″ 3 @ 24-21/32″
7′-10″ 3 @ 25-21/64″
1 3/4
Door 8′-0″ 3 @ 26″
9′-0″ 3 @ 30″
10′-0″ 3 @ 34″
5″ Hinge & Strike Comparison for 1-3/4″ Thick Doors

A B C D E F G H J
6′-8″ 2 @ 31″
6′-10″ 2 @ 32″
5" x 4 1/2" 7′-0″ 2 @ 33″
or
5" x 5" Hinge Frame 7′-2″ 2 @ 34″
F 7′-4″ 2 @ 35″
7′-6″ 41-13/16″ 9″ 2 @ 36″ 9″ 5/16″ 1/4″ 1/8″ 1/16″
H
J 7′-8″ 3 @ 24-21/32″
G
7′-10″ 3 @ 25-21/64″
1 3/4
Door 8′-0″ 3 @ 26″
9′-0″ 3 @ 30″
10′-0″ 3 @ 34″
2
SDI 129-14
Curries
EC
Opening
Height D
Hinge
CL Spacing
Note: On 3 1/2″ hinge preparation for 1 3/8″ doors, the standard for non-fire rated
frames is two (2) hinges.
B
Strike
CL
C
3 1/2″ x 3 1/2″
Hinge
Frame
F A B C D E F G
6′-8″ 10-3/8″ 2 @ 29-15/16″
1/8
1/16
7′-0″ 40-5/16″ 10-3/8″ 2 @ 31-15/16″ 9-3/4″ 5/16″ 1/4″
G
7′-2″ 10-3/8″ 2 @ 32-15/16″
1 3/8
Door

A B C D E F G H J
6′-8″ 12-1/4″ 2 @ 30-1/4″
6′-10″ 12-1/4″ 2 @ 31-1/4″
4 1/2″ x 4 1/2″ 7′-0″ 12-1/4″ 2 @ 32-1/4″
Hinge Frame 7′-2″ 12-1/4″ 2 @ 33-1/4″
F 7′-4″ 12-1/4″ 2 @ 34-1/4″
7′-6″ 40″ 12-1/4″ 2 @ 35-1/4″ 7-1/4″ 5/16″ 1/4″ 1/8″ 1/16″
H
J
G
7′-8″ 12-3/8″ 3 @ 24-1/8″
7′-10″ 12-1/8″ 3 @ 24-7/8″
1 3/4
Door 8′-0″ 12-1/4″ 3 @ 25-1/2″
9′-0″ 12-1/4″ 3 @ 29-1/2″
10′-0″ 12-1/4″ 3 @ 33-1/2″

A B C D E F G H J
6′-8″ 12-1/4″ 2 @ 30-1/4″
6′-10″ 12-1/4″ 2 @ 31-1/4″
5" x 4 1/2" 7′-0″ 12-1/4″ 2 @ 32-1/4″
or
5" x 5" Hinge Frame 7′-2″ 12-1/4″ 2 @ 33-1/4″
F 7′-4″ 12-1/4″ 2 @ 34-1/4″
7′-6″ 40″ 12-1/4″ 2 @ 35-1/4″ 7-1/4″ 5/16″ 1/4″ 1/8″ 1/16″
H
J 7′-8″ 12-3/8″ 3 @ 24-1/8″
G
7′-10″ 12-1/8″ 3 @ 24-7/8″
1 3/4
Door 8′-0″ 12-1/4″ 3 @ 25-1/2″
9′-0″ 12-1/4″ 3 @ 29-1/2″
10′-0″ 12-1/4″ 3 @ 33-1/2″
3
SDI 129-14
EC
Opening
Height D
Hinge
CL Spacing
B
Strike
CL
C
3 1/2″ x 3 1/2″
Hinge
Frame
F A B C D E F G
6′-8″ 61-1/2″
1/8
1/16
7′-0″ 40-5/16″ 11-3/4″ 2 @ 32-3/4″ 6-3/4″ 5/16″ 1/4″
G
7′-2″ 2 @ 33-3/4″
1 3/8
Door

A B C D E F G H J
6′-8″ 2 @ 30-1/4″
6′-10″ 2 @ 31-1/4″
4 1/2″ x 4 1/2″ 7′-0″ 2 @ 32-1/4″
Hinge Frame 7′-2″ 2 @ 33-1/4″
F 7′-4″ 2 @ 34-1/4″
7′-6″ 40-5/16″ 12-1/4″ 2 @ 35-1/4″ 7-1/4″ 5/16″ 1/4″ 1/8″ 1/16″
H
J
G
7′-8″ 24-1/8″, 24-1/4″, 24-1/8″
7′-10″ 24-7/8″, 24-3/4″, 24-7/8″
1 3/4
Door 8′-0″ 3 @ 25-1/2″
9′-0″ 3 @ 29-1/2″
10′-0″ 3 @ 33-1/2″

A B C D E F G H J
6′-8″ 12-1/2″ 2 @ 30″
6′-10″ 12-1/2″ 2 @ 31″
5" x 4 1/2" 7′-0″ 12-1/2″ 2 @ 32″
or
5" x 5" Hinge Frame 7′-2″ 12-1/2″ 2 @ 33″
F 7′-4″ 12-1/2″ 2 @ 34″
7′-6″ 40-5/16″ 12-1/2″ 2 @ 35″ 7-1/2″ 5/16″ 1/4″ 1/8″ 1/16″
H
J 7′-8″ 12-1/2″ 3 @ 24″
G
7′-10″ 12-1/2″ 24-5/8″, 24-3/4″, 24-5/8″
1 3/4
Door 8′-0″ 12-1/2″ 25-3/8″, 25-1/4″, 25-3/8″
9′-0″ 12-9/16″ 3 @ 29-5/16″
10′-0″ 12-9/16″ 3 @ 33-5/16″
4
SDI 129-14
Door Components Inc.
EC
Opening
Height D
Hinge
CL Spacing
B
Strike
CL
C
3 1/2″ x 3 1/2″
Hinge
Frame
F A B C D E F G
6′-8″ 2 @ 29-15/16″
1/8
1/16
7′-0″ 40-5/16″ 10-3/8″ 2 @ 31-15/16″ 9-3/4″ 5/16″ 1/4″
G
7′-2″ 2 @ 32-15/16″
1 3/8
Door

A B C D E F G H J
6′-8″ 2 @ 29-15/16″
6′-10″ 2 @ 30-15/16″
4 1/2″ x 4 1/2″ 7′-0″ 2 @ 31-15/16″
Hinge Frame 7′-2″ 2 @ 32-15/16″
F 7′-4″ 2 @ 33-15/16″
7′-6″ 40-5/16″ 10-3/8″ 2 @ 34-15/16″ 9-3/4″ 5/16″ 1/4″ 1/8″ 1/16″
H
J
G
7′-8″ 23-15/16″, 24″, 23-15/16″
7′-10″ 3 @ 24-5/8″
1 3/4
Door 8′-0″ 25-5/16″, 25-1/4″, 25-5/16″
9′-0″ 29-5/16″, 29-1/4″, 29-5/16″
10′-0″ 33-5/16″, 33-1/4″, 33-5/16″

A B C D E F G H J
6′-8″ 2 @ 29-15/16″
6′-10″ 2 @ 30-15/16″
5" x 4 1/2" 7′-0″ 2 @ 31-15/16″
or
5" x 5" Hinge Frame 7′-2″ 2 @ 32-15/16″
F 7′-4″ 2 @ 33-15/16″
7′-6″ 40-5/16″ 10-3/8″ 2 @ 34-15/16″ 9-3/4″ 5/16″ 1/4″ 1/8″ 1/16″
H
J 7′-8″ 23-15/16″, 24″, 23-15/16″
G
7′-10″ 3 @ 24-5/8″
1 3/4
Door 8′-0″ 25-5/16″, 25-1/4″, 25-5/16″
9′-0″ 29-5/16″, 29-1/4″, 29-5/16″
10′-0″ 33-5/16″, 33-1/4″, 33-5/16″
5
SDI 129-14
Hollow Metal Xpress
EC
Opening
Height D
Hinge
CL Spacing
B
Strike
CL
C
3 1/2″ x 3 1/2″
Hinge
Frame
F A B C D E F G
1/8
1/16
— — — — — — —
G
1 3/8
Door

A B C D E F G H J
6′-8″ 2 @ 29-15/16″
6′-10″ 2 @ 30-15/16″
4 1/2″ x 4 1/2″ 7′-0″ 2 @ 31-15/16″
Hinge Frame 7′-2″ 2 @ 32-15/16″
F 7′-4″ 2 @ 33-15/16″
7′-6″ 40-5/16″ 10-3/8″ 2 @ 34-15/16″ 9-3/4″ 3/8″ 1/4″ 1/16″ 1/8″
H
J
G
7′-8″ 3 @ 23-61/64″
7′-10″ 3 @ 24-5/8″
1 3/4
Door 8′-0″ 3 @ 25-19/64″
9′-0″ 3 @ 29-19/64″
10′-0″ 3 @ 33-19/64″

A B C D E F G H J
6′-8″ 2 @ 29-15/16″
6′-10″ 2 @ 30-15/16″
5" x 4 1/2" 7′-0″ 2 @ 31-15/16″
or
5" x 5" Hinge Frame 7′-2″ 2 @ 32-15/16″
F 7′-4″ 2 @ 33-15/16″
7′-6″ 40-5/16″ 10-3/8″ 2 @ 34-15/16″ 9-3/4″ 3/8″ 1/4″ 1/16″ 1/8″
H
J 7′-8″ 3 @ 23-61/64″
G
7′-10″ 3 @ 24-5/8″
1 3/4
Door 8′-0″ 3 @ 25-19/64″
9′-0″ 3 @ 29-19/64″
10′-0″ 3 @ 33-19/64″
6
SDI 129-14
Mesker Door, Inc.
EC
Opening
Height D
Hinge
CL Spacing
B
Strike
CL
C
3 1/2″ x 3 1/2″
Hinge
Frame
F A B C D E F G
6′-8″ 61-1/2″
1/8
1/16
7′-0″ 40-5/16″ 11-3/4″ 2 @ 32-3/4″ 6-3/4″ 1/4″ 3/16″
G
7′-2″ 2 @ 33-3/4″
1 3/8
Door

A B C D E F G H J
6′-8″ 12-1/4″ 2 @ 30-1/4″
6′-10″ 12-1/4″ 2 @ 31-1/4″
4 1/2″ x 4 1/2″ 7′-0″ 12-1/4″ 2 @ 32-1/4″
Hinge Frame 7′-2″ 12-1/4″ 2 @ 33-1/4″
F 7′-4″ 12-1/4″ 2 @ 34-1/4″
7′-6″ 40-5/16″ 12-1/4″ 2 @ 35-1/4″ 7-1/4″ 5/16″ 1/4″ 1/8″ 1/16″
H
J
G
7′-8″ 11-1/4″ 3 @ 24-1/2″
7′-10″ 10-1/4″ 3 @ 25-1/2″
1 3/4
Door 8′-0″ 12-1/4″ 3 @ 25-1/2″
9′-0″ 12-1/4″ 3 @ 29-1/2″
10′-0″ 12-1/4″ 4 @ 25-1/8″

A B C D E F G H J
6′-8″ 12-1/4″ 2 @ 30-1/4″
6′-10″ 12-1/4″ 2 @ 31-1/4″
5" x 4 1/2" 7′-0″ 12-1/4″ 2 @ 32-1/4″
or
5" x 5" Hinge Frame 7′-2″ 12-1/4″ 2 @ 33-1/4″
F 7′-4″ 12-1/4″ 2 @ 34-1/4″
7′-6″ 40-5/16″ 12-1/4″ 2 @ 35-1/4″ 7-1/4″ 5/16″ 1/4″ 1/8″ 1/16″
H
J 7′-8″ 11-1/4″ 3 @ 24-1/2″
G
7′-10″ 10-1/4″ 3 @ 25-1/2″
1 3/4
Door 8′-0″ 12-1/4″ 3 @ 25-1/2″
9′-0″ 12-1/4″ 3 @ 29-1/2″
10′-0″ 12-1/4″ 4 @ 25-1/8″
7
SDI 129-14
MPI
EC
Opening
Height D
Hinge
CL Spacing
B
Strike
CL
C
3 1/2″ x 3 1/2″
Hinge
Frame
F A B C D E F G
6′-8″ 2 @ 30-3/4″
1/8
1/16
7′-0″ 40-5/16″ 11-3/4″ 2 @ 32-3/4″ 6-3/4″ 5/16″ 1/4″
G
7′-2″ 2 @ 33-3/4″
1 3/8
Door

A B C D E F G H J
6′-8″ 2 @ 30-1/4″
6′-10″ 2 @ 31-1/4″
4 1/2″ x 4 1/2″ 7′-0″ 2 @ 32-1/4″
Hinge Frame 7′-2″ 2 @ 33-1/4″
F 7′-4″ 2 @ 34-1/4″
7′-6″ 40-5/16″ 12-1/4″ 2 @ 35-1/4″ 7-1/4″ 5/16″ 1/4″ 1/8″ 1/16″
H
J
G
7′-8″ 2 @ 24-3/16″, 1 @ 24-1/8″
7′-10″ 2 @ 24-13/16″, 1 @ 24-7/8″
1 3/4
Door 8′-0″ 3 @ 25-1/2″
9′-0″ 3 @ 29-1/2″
10′-0″ 3 @ 33-1/2″

A B C D E F G H J
6′-8″ 2 @ 30
6′-10″ 2 @ 31
5" x 4 1/2" 7′-0″ 2 @ 32
or
5" x 5" Hinge Frame 7′-2″ 2 @ 33
F 7′-4″ 2 @ 34
7′-6″ 40-5/16″ 12-1/2″ 2 @ 35 7-1/2″ 5/16″ 1/4″ 1/8″ 1/16″
H
J 7′-8″ 3 @ 24
G
7′-10″ 2 @ 24-11/16″, 1 @ 24-5/8″
1 3/4
Door 8′-0″ 2 @ 25-5/16″, 1 @ 25-3/8″
9′-0″ 2 @ 29-5/16″, 1 @ 29-3/8″
10′-0″ 2 @ 33-5/16″, 1 @ 33-3/8″
8
SDI 129-14
Pioneer Industries, Inc. – Standard
EC
Opening
Height D
Hinge
CL Spacing
B
Strike
CL
C
3 1/2″ x 3 1/2″
Hinge
Frame
F A B C D E F G
6′-8″ 2 @ 30-3/4″
1/8
1/16
7′-0″ 38″ 11-3/4″ 2 @ 32-3/4″ 6-3/4″ 5/16″ 7/32″
G
7′-2″ 2 @ 33-3/4″
1 3/8
Door

A B C D E F G H J
6′-8″ 12-1/4″ 2 @ 30-1/4″
6′-10″ 12-1/4″ 2 @ 31-1/4″
4 1/2″ x 4 1/2″ 7′-0″ 12-1/4″ 2 @ 32-1/4″
Hinge Frame 7′-2″ 12-1/4″ 2 @ 33-1/4″
F 7′-4″ 12-1/4″ 2 @ 34-1/4″
7′-6″ 38″ 12-1/4″ 3 @ 23-1/2″ 7-1/4″ 5/16″ 7/32″ 3/32″ 3/32″
H
J
G
7′-8″ 12-3/16″ 3 @ 24-3/16″
7′-10″ 12-5/16″ 3 @ 24-13/16″
1 3/4
Door 8′-0″ 12-1/4″ 3 @ 25-1/2″
9′-0″ 12-1/4″ 3 @ 29-1/2″
10′-0″ 12-1/4″ 3 @ 33-1/2″

A B C D E F G H J
6′-8″ 12-1/2″ 2 @ 30″
6′-10″ 12-1/2″ 2 @ 31″
5" x 4 1/2" 7′-0″ 12-1/2″ 2 @ 32″
or
5" x 5" Hinge Frame 7′-2″ 12-1/2″ 2 @ 33″
F 7′-4″ 12-1/2″ 2 @ 34″
7′-6″ 38″ 12-9/16″ 3 @ 23-5/16″ 7-1/2″ 5/16″ 7/32″ 3/32″ 3/32″
H
J 7′-8″ 12-1/2″ 3 @ 24″
G
7′-10″ 12-5/8″ 3 @ 24-5/8″
1 3/4
Door 8′-0″ 12-9/16″ 3 @ 25-5/16″
9′-0″ 12-9/16″ 3 @ 29-5/16″
10′-0″ 12-9/16″ 3 @ 33-5/16″
9
SDI 129-14
Pioneer Industries, Inc. – S-Series
EC
Opening
Height D recommends that individual manufacturers be contacted to verify dimensions.
Hinge
CL Spacing
B
Strike
CL
C
3 1/2″ x 3 1/2″
Hinge
Frame 3-1/2″ Hinge & Strike Comparison for 1-3/8″ Thick Doors
F A B C D E F G
6′-8″ 2 @ 29-15/16″
1/8
1/16
G
7′-0″ 40-5/16″ 10-3/8″ 2 @ 31-15/16″ 9-3/4″ 5/16″ 7/32″
7′-2″ 2 @ 32-15/16″
1 3/8
Door

A B C D E F G H J
6′-8″ 2 @ 29-15/16″
6′-10″ 2 @ 30-15/16″
4 1/2″ x 4 1/2″ 7′-0″ 2 @ 31-15/16″
Hinge Frame 7′-2″ 2 @ 32-15/16″
F 7′-4″ 2 @ 33-15/16″
H
7′-6″ 40-5/16″ 10-3/8″ 2 @ 34-15/16″ 9-3/4″ 5/16″ 7/32″ 3/32″ 3/32″
J
G 7′-8″ 3 @ 23-61/64″
7′-10″ 3 @ 24-5/8″
1 3/4
Door 8′-0″ 3 @ 25-19/64″
9′-0″ 3 @ 29-19/64″
10′-0″ 3 @ 33-19/64″

A B C D E F G H J
6′-8″ 2 @ 29-15/16″
6′-10″ 2 @ 30-15/16″
5" x 4 1/2" 7′-0″ 2 @ 31-15/16″
or
5" x 5" Hinge Frame 7′-2″ 2 @ 32-15/16″
F 7′-4″ 2 @ 33-15/16″
7′-6″ 40-5/16″ 10-3/8″ 2 @ 34-15/16″ 9-3/4″ 5/16″ 7/32″ 3/32″ 3/32″
H
J 7′-8″ 3 @ 23-61/64″
G
7′-10″ 3 @ 24-5/8″
1 3/4
Door 8′-0″ 3 @ 25-19/64″
9′-0″ 3 @ 29-19/64″
10′-0″ 3 @ 33-19/64″
10
SDI 129-14
Republic Doors & Frames
EC
Opening
Height D
Hinge
CL Spacing
B
Strike
CL
C
3 1/2″ x 3 1/2″
Hinge
Frame
F A B C D E F G
6′-8″ 61-1/2″
1/8
1/16
6′-8″ 2 @ 30-3/4″
G 40-5/16″ 11-3/4″ 6-3/4″ 5/16″ 1/4″
7′-0″ 2 @ 32-3/4″
1 3/8
Door 7′-2″ 2 @ 33-3/4″

A B C D E F G H J
6′-8″ 10-3/8″ 2 @ 29-15/16″ 9-3/4″
6′-10″ 12-1/4″ 2 @ 31-1/4″ 7-1/4″
4 1/2″ x 4 1/2″ 7′-0″ 12-3/8″ 2 @ 29-15/16″ 11-3/4″
Hinge Frame 7′-2″ 12-1/4″ 2 @ 33-1/4″ 7-1/4″
F 7′-4″ 12-1/4″ 2 @ 34-1/4″ 7-1/4″
7′-6″ 40-5/16″ 12-1/4″ 2 @ 35-1/4″ 7-1/4″ 5/16″ 1/4″ 1/8″ 1/16″
H
J
G
7′-8″ 12-1/4″ 3 @ 24-11/64″ 7-1/4″
7′-10″ 12-1/4″ 3 @ 24-53/64″ 7-1/4″
1 3/4
Door 8′-0″ 12-1/4″ 3 @ 25-1/2″ 7-1/4″
9′-0″ 12-1/4″ 3 @ 29-1/2″ 7-1/4″
10′-0″ 12-1/4″ 3 @ 33-1/2″ 7-1/4″

A B C D E F G H J
6′-8″ 2 @ 30″
6′-10″ 2 @ 31″
5" x 4 1/2" 7′-0″ 2 @ 32″
or
5" x 5" Hinge Frame 7′-2″ 2 @ 33″
F 7′-4″ 2 @ 34″
7′-6″ 40-5/16″ 12-1/2″ 2 @ 35″ 7-1/2″ 5/16″ 1/4″ 1/8″ 1/16″
H
J 7′-8″ 3 @ 24″
G
7′-10″ 3 @ 24-43/64″
1 3/4
Door 8′-0″ 3 @ 25-21/64″
9′-0″ 3 @ 29-21/64″
10′-0″ 3 @ 33-21/64″
11
SDI 129-14
Security Metal Products
EC
Opening
Height D
CL
Hinge
Spacing
Note: Does not manufacture 1 3/8″ thick doors. Frames for 1 3/8″ doors are manu-
factured by special arrangement only.
B
Strike
CL
C
3 1/2″ x 3 1/2″
Hinge
Frame
F A B C D E F G
1/8
1/16
— — — — — — —
G
1 3/8
Door

A B C D E F G H J
6′-8″ 12-1/4″ 2 @ 30-1/4″
6′-10″ 12-1/4″ 2 @ 31-1/4″
4 1/2″ x 4 1/2″ 7′-0″ 12-1/4″ 2 @ 32-1/4″
Hinge Frame 7′-2″ 12-1/4″ 2 @ 33-1/4″
F 7′-4″ 12-1/4″ 2 @ 34-1/4″
7′-6″ 40-5/16″ 10-1/4″ 2 @ 36-1/4″ 7-1/4″ 3/8″ 1/4″ 1/16″ 1/8″
H
J
G
7′-8″ 12-1/4″ 3 @ 24-11/64″
7′-10″ 12-1/4″ 3 @ 24-53/64″
1 3/4
Door 8′-0″ 12-1/4″ 3 @ 25-1/2″
9′-0″ 10-1/4″ 3 @ 30-5/32″
10′-0″ 12-1/4″ 3 @ 33-1/2″

A B C D E F G H J
6′-8″ 12-1/2″ 2 @ 30″
6′-10″ 12-1/2″ 2 @ 31″
5" x 4 1/2" 7′-0″ 12-1/2″ 2 @ 32″
or
5" x 5" Hinge Frame 7′-2″ 12-1/2″ 2 @ 33″
F 7′-4″ 12-1/2″ 2 @ 34″
7′-6″ 40-5/16″ 10-1/2″ 2 @ 36″ 7-1/2″ 3/8″ 1/4″ 1/16″ 1/8″
H
J 7′-8″ 12-1/2″ 3 @ 24″
G
7′-10″ 12-1/2″ 3 @ 24-43/64″
1 3/4
Door 8′-0″ 12-1/2″ 3 @ 25-21/64″
9′-0″ 10-1/2″ 3 @ 30″
10′-0″ 12-1/2″ 3 @ 33-21/64″
12
SDI 129-14
Steelcraft
EC
Opening
Height D
Hinge
CL Spacing
B
Strike
CL
C
3 1/2″ x 3 1/2″
Hinge
Frame
F A B C D E F G
6′-8″ 59-7/8″
1/8
1/16
7′-0″ 40-5/16″ 10-3/8″ 2 @ 31-15/16″ 9-3/4″ 5/16″ 1/4″
G
7′-2″ 2 @ 32-15/16″
1 3/8
Door

A B C D E F G H J
6′-8″ 2 @ 29-15/16″
6′-10″ 2 @ 30-15/16″
4 1/2″ x 4 1/2″ 7′-0″ 2 @ 31-15/16″
Hinge Frame 7′-2″ 2 @ 32-15/16″
F 7′-4″ 2 @ 33-15/16″
7′-6″ 40-5/16″ 10-3/8″ 2 @ 34-15/16″ 9-3/4″ 5/16″ 1/4″ 1/8″ 1/16″
H
J
G
7′-8″ 3 @ 23-61/64″
7′-10″ 3 @ 24-5/8″
1 3/4
Door 8′-0″ 3 @ 25-19/64″
9′-0″ 3 @ 29-19/64″
10′-0″ 3 @ 33-19/64″

A B C D E F G H J
6′-8″ 2 @ 29-15/16″
6′-10″ 2 @ 30-15/16″
5" x 4 1/2" 7′-0″ 2 @ 31-15/16″
or
5" x 5" Hinge Frame 7′-2″ 2 @ 32-15/16″
F 7′-4″ 2 @ 33-15/16″
7′-6″ 40-5/16″ 10-3/8″ 2 @ 34-15/16″ 9-3/4″ 5/16″ 1/4″ 1/8″ 1/16″
H
J 7′-8″ 3 @ 23-61/64″
G
7′-10″ 3 @ 24-5/8″
1 3/4
Door 8′-0″ 3 @ 25-19/64″
9′-0″ 3 @ 29-19/64″
10′-0″ 3 @ 33-19/64″
13
SDI 129-14
The following companies are included for historical purposes only.

The validity of their hinge and strike spacing data cannot be confirmed.
14
SDI 129-14
Benchmark
EC
L Note: Benchmark is no longer a member of the Steel Door Institute. Its hinge and
A strike spacing are included for legacy purposes; the validity of the data cannot
Opening
Height D
be confirmed
Hinge
CL Spacing
B
Strike
CL
C
3 1/2″ x 3 1/2″
Hinge
Frame
F A B C D E F G
— — — — — — —
1/8
1/16
G
1 3/8
Door

A B C D E F G H J
6′-8″ 12-1/4″ 2 @ 30-1/4″
6′-10″ 14-1/4″ 2 @ 30-1/4″
4 1/2″ x 4 1/2″
7′-0″ 12-1/4″ 2 @ 32-1/4″
Hinge Frame 7′-2″ 14-1/4″ 2 @ 32-1/4″
F 7′-4″ 40-5/16″ 12-1/4″ 2 @ 34-1/4″ 7-1/4″ 11/32″ 1/4″ 1/8″ 3/32″
7′-6″ 14-1/4″ 2 @ 34-1/4″
H
J 7′-8″ 8-1/4″ 3 @ 25-1/2″
G
7′-10″ 10-1/4″ 3 @ 25-1/2″
1 3/4
Door 8′-0″ 12-1/4″ 3 @ 25-1/2″

A B C D E F G H J
— — — — — — — — —
5" x 4 1/2"
or
5" x 5" Hinge Frame
F
H
J
G
1 3/4
Door
15
SDI 129-14
Black Mountain Door
EC
Opening
Height D
Hinge
CL Spacing
B
Strike
CL
C
3 1/2″ x 3 1/2″
Hinge
Frame
F A B C D E F G
6′-8″ 10-3/8″
1/8
1/16 7′-0″ 40-5/16″ 14-3/8″ 59-7/8″ 9-3/4″ 5/16″ 3/16″
G
7′-2″ 16-3/8″
1 3/8
Door

A B C D E F G H J
6′-8″ 10-3/8″ 2 @ 29-15/16″
6′-10″ 8-3/8″ 2 @ 31-15/16″
4 1/2″ x 4 1/2″ 7′-0″ 10-3/8″ 2 @ 31-15/16″
Hinge Frame 7′-2″ 12-3/8″ 2 @ 31-15/16″
F 7′-4″ 10-3/8″ 2 @ 33-15/16″
7′-6″ 40-5/16″ 12-3/8″ 2 @ 33-15/16″ 9-3/4″ 5/16″ 3/16″ 1/16″ 1/8″
H
J
G
7′-8″ 10-7/16″ 3 @ 23-15/16″
7′-10″ 8-5/16″ 3 @ 25-5/16″
1 3/4
Door 8′-0″ 10-5/16″ 3 @ 25-5/16″
9′-0″ 8-7/16″ 3 @ 29-15/16″
10′-0″ 11-7/16″ 3 @ 32-15/16″

A B C D E F G H J
6′-8″ 10-3/8″ 2 @ 29-15/16″
6′-10″ 8-3/8″ 2 @ 31-15/16″
5" x 4 1/2" 7′-0″ 10-3/8″ 2 @ 31-15/16″
or
5" x 5" Hinge Frame 7′-2″ 12-3/8″ 2 @ 31-15/16″
F 7′-4″ 10-3/8″ 2 @ 33-15/16″
7′-6″ 40-5/16″ 12-3/8″ 2 @ 33-15/16″ 9-3/4″ 5/16″ 3/16″ 1/16″ 1/8″
H
J 7′-8″ 10-7/16″ 3 @ 23-15/16″
G
7′-10″ 8-5/16″ 3 @ 25-5/16″
1 3/4
Door 8′-0″ 10-5/16″ 3 @ 25-5/16″
9′-0″ 8-7/16″ 3 @ 29-15/16″
10′-0″ 11-7/16″ 3 @ 32-15/16″
16
SDI 129-14
Copco
EC
L Note: Copco is no longer a member of the Steel Door Institute. Its hinge and strike
A spacing are included for legacy purposes; the validity of the data cannot be
Opening
Height D
confirmed
Hinge
CL Spacing
B
Strike
CL
C
3 1/2″ x 3 1/2″
Hinge
Frame
F A B C D E F G
6′-8″ 2 @ 29-15/16″
1/8
1/16
G
7′-0″ 40-5/16″ 10-3/8″ 2 @ 31-15/16″ 9-3/4″ 5/16″ 7/32″
7′-2″ 2 @ 32-15/16″
1 3/8
Door

A B C D E F G H J
6′-8″ 2 @ 29-15/16″
6′-10″ 2 @ 30-15/16″
4 1/2″ x 4 1/2″ 7′-0″ 2 @ 31-15/16″
Hinge Frame 7′-2″ 2 @ 32-15/16″
F 7′-4″ 40-5/16″ 10-3/8″ 2 @ 33-15/16″ 9-3/4″ 5/16″ 7/32″ 1/32″ 3/32″
7′-6″ 2 @ 34-15/16″
H
J
G
7′-8″ 3 @ 23-19/64″
7′-10″ 3 @ 24-19/64″
1 3/4
Door 8′-0″ 3 @ 25-19/64″

A B C D E F G H J
6′-8″ 2 @ 29-15/16″
6′-10″ 2 @ 30-15/16″
5" x 4 1/2" 7′-0″ 2 @ 31-15/16″
or
5" x 5" Hinge Frame 7′-2″ 2 @ 32-15/16″
F
7′-4″ 40-5/16″ 10-3/8″ 2 @ 33-15/16″ 9-3/4″ 5/16″ 7/32″ 1/32″ 3/32″
H 7′-6″ 2 @ 34-15/16″
J
G 7′-8″ 3 @ 23-19/64″
1 3/4 7′-10″ 3 @ 24-19/64″
Door
8′-0″ 3 @ 25-19/64″
17
SDI 129-14
Kewanee
EC
L Note: Kewanee is no longer a member of the Steel Door Institute. Its hinge and
A strike spacing are included for legacy purposes; the validity of the data cannot
Opening
Height D
be confirmed
Hinge
CL Spacing
B
Strike
CL
C
3 1/2″ x 3 1/2″
Hinge
Frame
F A B C D E F G
6′-8″ 60-1/8″
1/8
1/16
G
7′-0″ 40-5/16″ 11-3/4″ 2 @ 32-1/16″ 9-5/8″ 1/4″ 3/16″
7′-2″ 2 @ 33-1/16″
1 3/8
Door

A B C D E F G H J
6′-8″ 2 @ 30-1/16″
6′-10″ 2 @ 31-1/16″
4 1/2″ x 4 1/2″ 7′-0″ 2 @ 32-1/16″
Hinge Frame 7′-2″ 2 @ 33-1/16″
F 7′-4″ 40-5/16″ 10-1/4″ 2 @ 34-1/16″ 9-5/8″ 3/8″ 1/4″ 1/16″ 1/8″
7′-6″ 2 @ 35-1/16″
H
J
G
7′-8″ 24-1/16″, 24″, 24-1/16″
7′-10″ 24-11/16″, 24-3/4″, 24-11/16″
1 3/4
Door 8′-0″ 3 @ 25-3/8″

A B C D E F G H J
6′-8″ 2 @ 30-1/16″
6′-10″ 2 @ 31-1/16″
5" x 4 1/2" 7′-0″ 2 @ 32-1/16″
or
5" x 5" Hinge Frame 7′-2″ 2 @ 33-1/16″
F 7′-4″ 40-5/16″ 10-1/4″ 2 @ 34-1/16″ 9-5/8″ 3/8″ 1/4″ 1/16″ 1/8″
7′-6″ 2 @ 35-1/16″
H
J 7′-8″ 24-1/16″, 24″, 24-1/16″
G
7′-10″ 24-11/16″, 24-3/4″, 24-11/16″
1 3/4
Door 8′-0″ 3 @ 25-3/8″
18
MEMBERS OF THE
Ceco Door
Milan, TN 38358
Curries
www.deansteel.com
Test Procedures
(909) 770-5700
HOLLOW METAL XPRESS
623-936-7000
www.meskerdoor.com
Corbin, KY 40701
155 Republic Drive
www.secmet.com
9017 Blue Ash Road
(513) 745-6400

440.899.0010 • FAX 440.892.1404
12/4/2014
www.steeldoor.org
SDI
130 - 15
Electronic Hinge
Preparations

SDI 130-15
Electronic Hinge Preparations
1 Purpose
It is the intention of this document to furnish users of standard steel frames with practical information regarding an
acceptable method for preparing frames for 4-1/2″, 5″ or continuous electric hinges. This document will allow frame
manufacturers to provide frames prior to having knowledge of the specific electric hinge being used.
2 Scope
The information contained herein pertains to frames manufactured in accordance with ANSI/SDI A250.8. The
preparation as defined herein will accommodate the majority of electric hinges sold. It is the responsibility of the
hardware specifier to assure compatible hinges are used.
3 Reference Documents
ANSI/SDI A250.6 Recommended Practice for Hardware Reinforcings on Standard Steel Doors and Frames
ANSI/BHMA A156.7 Template Hinge Dimensions
ANSI/BHMA A156.115 Hardware Preparation in Steel Doors and Steel Frames
4 Location
The preparation for electric hinges is intended to be non-load bearing. Therefore it shall be located in the center
hinge preparation on frames with 1-1/2 pair of hinges, and on the second hinge from the bottom on frames with 2
pair of hinges.
5 Hinge Reinforcement
The hinge reinforcement shall comply with ANSI/SDI A250.6 and ANSI/SDI A250.8, and shall incorporate cutouts
as shown in Figures 1, 2, 3 and 4.
6 Junction Box
A junction box may be provided to facilitate wiring and connector installation. In addition, a hole shall be provided
at the top and bottom of the junction box to facilitate conduit (see Figure 4). It is the responsibility of the electrical
contractor to plug any unused holes.
1
SDI 130-15
Note 1: The hinge backset on the door varies by hollow metal door manufactures from 3/16″ to 1/4″
Note 2: The hinge backset on the frame varies by hollow metal frame manufactures from 5/16″ to 3/8″
Note 3: Extra holes may occur in the reinforcement for tooling and installation fixturing.
Note 4: Some manufacturers offer a removable feature (e.g. - wire, shim, standoff projection) to allow conver-
sion of a standard weight preparation for use with heavy weight hinge butt.
Note 5: The most common mortise depths are in accordance with ANSI/BHMA A156.1 as follows:
Standard Weight butt 0.146″
Heavy weight butt 0.190″
Figure 1 – Preparation of 1 3/4″ Steel Doors & Frames for 5″ Full Mortise Electric Hinge
2
SDI 130-15
Note 1: The hinge backset on the door varies by hollow metal door manufactures from 3/16″ to 1/4″
Figure 2 – Preparation of 1 3/4″ Steel Doors & Frames for 4 1/2″ Full Mortise Electric Hinge
3
SDI 130-15
Note 1: The hinge backset on the door varies by hollow metal door manufactures from 3/16″ to 1/4″ when hinge
filler is in place.
Figure 3 – Preparation of 1 3/4″ Steel Doors & Frames for 4 1/2″ Full Mortise Electric Hinge Non-handed
4
SDI 130-15
Figure 4 – Electrified Continuous Hinge Preparation on Standard Steel Frame
5
MEMBERS OF THE
Ceco
9159 Telecom Drive
www.cecodoor.com
Curries
1502 12th Street
www.curries.com
Frames
www.deansteel.com
(623) 936-7000
www.HMXpress.com
Mesker Door, LLc
(256) 851-6670
MPI
(606) 523-0173
Carlstadt, NJ 07072
(201) 933-1900
155 Republic Drive
(731) 352-3383
Frames SMP
(310) 641-6690
9017 Blue Ash Road
(513) 745-6400

440.899.0010 • FAX 440.892.1404
7/7/2015
www.steeldoor.org
SDI
131 - 15
Accelerated Physical Endurance

Test Procedure for Steel Doors

SDI 131-15
Accelerated Physical Endurance Test Procedure for Steel Doors
1 Purpose Care shall be taken to ensure the hinges are

properly applied to the door and frame, and
The purpose of this test procedure is to provide any required hinge fillers are in place. The initial
manufacturers with an accelerated method of clearances between the door and frame shall be
testing the performance of doors. recorded as part of the performance test report.
This test procedure will provide performance data Silencers, weather strip or gasketing shall be
for comparative purposes and is not intended installed on the frame, and the stop face of the
to simulate field operating conditions. This test door shall contact them.
will subject the product to more severe condi-
tions than those experienced in normal field 4 Test Specimen
operation. The test shall be performed on a 3'0" wide x
7'0" high nominal size door; although, other sizes
2 Apparatus and Equipment are permitted to be evaluated at the discretion
The main testing structure shall be constructed of the sponsor.
as shown in Figures 1 and 2. The structure shall A detailed description of the door construction
conform to the parts shown, except the opening shall be recorded as part of the test report.
width and height are permitted to vary, allowing This information shall cover all components as
the testing of various door sizes. well as applicable processes (such as welding,
The cycling mechanism shall be positioned so that bonding, etc.) used for attaching and connecting
the connecting arm is perpendicular to the stop components.
face of the door. It shall have a threaded swivel
connector that is attached to the door through 5 Cycle Test
the lock preparation or by means of a bracket The duration of the test shall be 250,000 cycles
mounted directly to the door face at the vertical for Level C; 500,000 cycles for Level B; 1,000,000
and horizontal location of the lock preparation. cycles for Level A; or longer, if specified by the
The cycling mechanism shall have an operating test sponsor. A general inspection of the door
stroke so that the door lock edge will be opened shall be made at 25,000 cycle intervals for the
not less than 4 inches from the frame stop and first 100,000 cycles and at 50,000 cycles there-
then returned to the closed position. The mini- after until the completion of the required number
mum cycle rate shall be one cycle per second. of cycles. The general inspection shall cover all
A mechanical or electronic counter shall be used components readily accessible, such as face
to record the cycles. skins, exposed hinge and/or lock edges, head
and sill closures, flush-closing channels, hinge
3 Preparation for Test reinforcements, etc. Additionally, the inspection
shall cover the welding, bonding, staking, me-
The door shall be hung in the frame on hinges
chanical interlocking, etc., used to connect the
conforming to the most current edition of ANSI
various door components.
A156.7-2009, “Template Hinge Dimensions”. The
hinges and their locations shall be noted on Form The results shall be recorded on a standard per-
1 of the report. formance report “Door Test Form 1.”
1
SDI 131-15

Figure 1 – Cycle Test Detail
When an independent organization is employed as described in Figure 2. The deflection noted

to certify the overall performance of the door on the dial indicator shall be plotted against
design, they shall validate the initial, mid-point, the load applied to the corner. A maximum 300
and final observations. pounds pressure shall be applied. The pressure
shall then be reduced in 30-pound increments
6 Twist Test and the deflection recorded on the report form.
Any deterioration of the door construction as a A smooth curve drawn through the points shall
result of the cycle testing shall be determined graphically demonstrate the reaction of the door.
through a series of twist tests. These tests shall Use “Performance Report – Door Test Form 2”
occur prior to the onset of the cycle test and at to graphically represent the deflections.
the end of the cycle test. Measurements for deflections shall be taken
During the twist test, the hinge pins shall be one minute or less after the force has been
removed and the door moved to the twist test stabilized.
fixture (if a separate fixture is used) and clamped At the completion of each twist test, and prior
in place as shown in Figure 2. to the continuance of the cycle test, the hinges
If the same fixture is used for both the cycle shall be inspected and lubricated or replaced,
test and twist test, the hinge pins shall be re- if necessary.
moved and the door clamped in place as shown
in Figure 2. 7 Acceptance Criteria
Pressures in 30-pound increments shall be applied 7.1 Doors shall not show any visible signs of
at the upper lock corner through the screw jack, metal fatigue cracking, or deformation on the
or equivalent device, and force gage in an area edges or the door face.
2
SDI 131-15
7.2 Doors of either laminated or welded construc- 7.6 As a result of the twist test, the maximum
tion shall not delaminate or have weld breakage deflection shall not exceed 2- 1/2 " when loaded
in excess of 10% of total bonded or welded to 300 lb for Level C doors. For Level B and A
surface. doors, the maximum deflection shall not exceed
1- 1/4 " when loaded to 300 lb.
7.3 Top, bottom, or edge channels must remain
securely in place, with no signs of weld or bond 7.7 Permanent deflection measured within 5-
breakage. minutes after the force is removed shall not
exceed 1/8 ".
7.4 Doors of stile and panel or stile and rail
construction shall not be misaligned.
7.5 Where visible seams are inherent in the door
design, no opening or spreading shall occur.
Note: Twist test to be made at beginning

and at end of cycle test.
Figure 2 – Twist Test Detail
3
4
Performance Report – Cycle Test Form No. 1
Door Manufacturer: Door Model: Hinge Manufacturer:

SDI 131-15
Weight of Door: Door Size: Hinge Model:

Test No.: Start Test Date: Finish Test Date:
Inspection Intervals – (000)
25 50 75 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000
Edge Condition
Top
Intermediate
Hinge
Preparations
Bottom
Top Closer Condition
Bottom Closer Condition
Condition of Core
Condition of Panels
“S” indicates satisfactory performance. Use footnotes under remarks for any further explanations.
Remarks:
Performance Report — Twist Test Form No. 2
Test No: Date:

Door Manufacturer: Door Model:
Door Size: Weight of Door:
3.0
2.5
2.0
1.5
Deflection – Inches
1.0
0.5
0.0
0 30 60 90 120 150 180 210 240 270 300 270 240 210 180 150 120 90 60 30 0
Applied Load – LBF
5
SDI 131-15
MEMBERS OF THE
CECO DOOR
Milan, TN 38358
CURRIES
SDI-128 Guidelines for Acoustical Performance of Standard Steel Doors & DEANSTEEL MANUFACTURING CO.
www.deansteel.com
Test Procedures
(909) 770-5700
HOLLOW METAL XPRESS
623-936-7000
(Not applicable for FEMA 320/361 or ICC-500 Shelters) MESKER DOOR, INC.
www.meskerdoor.com
Corbin, KY 40701
SDI-110 Standard Steel Doors & Frames for Modular Masonry Construction PIONEER INDUSTRIES, INC.
Frames REPUBLIC DOORS & FRAMES
155 Republic Drive
Frames SECURITY METAL PRODUCTS
www.secmet.com
SDI-130 Electrified Hinge Preparations STEELCRAFT
9017 Blue Ash Road
(513) 745-6400

440.899.0010 • FAX 440.892.1404
12/4/2014
www.steeldoor.org
SDI
133 - 16
Guideline for Specifying

for Blast Resistance

SDI 133-16
Guideline for Specifying Steel Doors and Frames for Blast Resistance
1 Introduction 2.4 Charge Weight: The equivalent explosive

weight (lbs. or kg) of TNT in the blast event.
Blast-resistant hardening, or the structural
Different agencies have specific requirements for
strengthening of buildings, is one measure an
owner may employ to minimize the risk to people charge weight to be used. See agency specific
and equipment from the hazards of accidental or criteria for DoD, VA, GSA, and DOS to determine
intentional explosions. Many architects are finding required charge weight and in some cases, the
it necessary to include blast-resistant products in required standoff distance.
new and existing construction. These products do 2.5 Duration: The amount of time it takes the peak
not fall under any building code, but are required
pressure to decay to ambient conditions (or zero).
by a number of government agencies such as
the Department of Defense (DoD), Veterans Af- 2.6 Rebound: Load acting in the opposite
fairs (VA), Department of State (DOS), and the direction of the initial blast load that may be a
General Services Administration (GSA). They are result of negative phase pressure loading and
backed by analysis or 3 rd party test data (from an system response, and is typically expressed as
accredited lab) to show their performance level a percentage of the initial peak blast pressure.
under blast load conditions. This document will
serve as a guide to identify the proper criteria, 2.7 Stand-off Distance: The distance from the
and to give brief explanations of each criterion. centroid of the explosive device to the specified
Additional requirements, fire rating, swing, etc. opening or structure.
are not covered.
2.8 Seated/Unseated: The orientation of the door
in the frame, in relation to the blast origin.
2 Definitions
2.1 Blast Resistant Product: Assembly comprised
of a door (or pair of doors) and a frame with
hardware, or a glazing system that is rated to resist
a specified blast peak pressure and impulse to a
required performance level. Higher level doors and
frames are typically sold and shipped as one unit
in order to be certified by the manufacturer that Seated Unseated
it will meet the projected blast and performance
requirements. 2.9 Blast Product Response & Damage Category
(Also referred to as Level of Protection in
2.2 Blast Pressure: The maximum pressure to the UFC): The amount of structural damage
be exerted on the assembly by the blast event.
(permanent deformation) present after the blast
2.3 Positive Phase Impulse: The area under the event. With respect to a door and frame unit, the
curve formed by the integral of blast pressure operability of the door, and whether or not the
(Pmax) vs. time (Td). door and/or frame become detached and present
a debris hazard. With respect to a glazing system,
whether or not the glazing fractures, and if it
presents a flying debris hazard. There are multiple
max
p
standard test methods written that outline test

Impulse procedures to follow to show how a blast-resistant
Pressure
unit will react in a blast event.

2 . 9 . 1 Pa ra p h ra s e d re s p o n s e a n d d a m a g e
t
d
categories are given on page 2 to highlight the
Time differences in test methods and design criteria. For
the full verbiage, please reference the specified
Blast Wave (Idealized) test methods and standards organization.
1
SDI 133-16
Blast Product Response & Damage Categories
UFC 4-010-01 – Levels of Protection

Below AT Standards Severe damage and/or collapse of structure
Very Low Heavy structural damage
Low Moderate damage, unable to be repaired economically
Medium Minor damage, able to be repaired economically
High Minimal damage, no permanent deformation
ASTM F2247-11 – Response Categories

Category I No permanent deformation to the specimen is present, and the door is fully
operable.
Category II Measurable permanent deformation is present, but the door is operable.
Category III Non-catastrophic failure, however the unit is inoperable.
Category IV The unit is severely deformed; however the door will not become a flying
debris hazard.
ASTM F2912-11 – Hazard Ratings

No Break (H1) No fractures are present in the glazing, and no damage is visible to the
unit.
No Hazard (H1) The glazing has fractured, but no breakage has occurred (no debris).
Minimal Hazard (H2) The glazing has fractured, and minimal fragments are present on the floor
near the interior face of the glazing system (between 0 and 40 inches).
Very Low Hazard The glazing has fractured and noticeable fragments are present on the
(H3) floor near the interior face of the glazing system (between 40 and 120
inches).
Low Hazard (H4) The glazing has fractured and fragments have fallen up to 120 inches
away from the interior face of the glazing system, but lower than 20 inches
above the floor.
High Hazard The glazing has fractured and fragments have fallen up to 120 inches away
from the interior face of the glazing system, and higher than 20 inches
above the floor.
ASTM F2927-12 – Door Response Damage Categories

Category I The door specimen is unchanged and fully operable.
Category II The unit has acceptable permanent deformation but it still operable.
Category III The unit has permanent deformation that may cause it to be lodged in the
frame, or to swing open in rebound. The door and frame stay together as
one unit.
Category IV The door can become separated from the frame and cause a flying debris
hazard, or the door and frame unit may separate from the wall and cause a
debris hazard. The flying debris will not go further than 3 meters.
Category V The door or the door and frame unit together become dislodged and cause
a flying debris hazard that will go further than 3 meters.
2
SDI 133-16
3 Blast Standard Test Methods and De- 3.5 GSA-TS01-2003 – Standard Test Method for
sign Criteria Glazing and Window Systems Subject to Dy-
namic Overpressure Loadings – The sole test
3.1 ASTM F2247 – Standard Test Method for
protocol by which blast resistant windows and
Metal Doors Used in Blast Resistant Applica-
related hazard mitigation technology and products
tions (Equivalent Static Load Method) – Deter-
shall be evaluated for facilities under the control
mines ultimate static capacity. Requires further
and responsibility of the US General Services
evaluation to relate to explosive charges or other
Administration.
dynamic loads
3.6 ASCE 2010, 2 nd edition – Design of Blast
3.2 ASTM F2927 – Standard Test Method for Door
Resistant Buildings in Petrochemical and Off-
Systems Subject to Airblast Loadings – Used to
shore Facilities
determine blast capacity for a shock wave created
by live explosives or a shock tube. 3.7 PIP STC01018 – Blast Resistant Building
Design Criteria for Petrochemical and Offshore
3.3 ASTM F2912 – Standard Specification for
Facilities
Glazing and Glazing Systems Subject to Airblast
Loadings – Used to determine blast capacity from 3.8 UFC 4-010-01 – Department of Defense Mini-
a shock wave or explosion mum Antiterrorism Standards for Buildings – The
intent is to minimize mass casualties in buildings
3.4 ASTM F1642 – Standard Test Method for
or portions of buildings owned, leased, privatized,
Glazing and Glazing Systems Subject to Airblast
or otherwise occupied, managed, or controlled
Loadings – The data obtained from this test
by or for DoD in the event of a terrorist attack.
method is used in ASTM F2912 to determine a
hazard rating.
Blast Requirements to be provided Sample Criteria Sample Criteria

(Except DoD Projects) (Door) (Window)
Product Size (Scheduled Opening) 3´-0˝ x 7´-0˝ Door & Frame 4´-0˝ x 4´-0˝ Window
Assy
Peak Pressure, Duration, & Rebound 4psi, 100ms, 50% Rebound 2psi, 200ms, 50% Rebound
Door Configuration (Seated/Unseated) Seated in Frame —
Wall Conditions Welded to Steel Subframe Anchored to Wall
Category Response II Very Low Hazard (H3)
per ASTM F2912-11
Applicable Blast Test Standard ASTM F2927-12 ASTM F1642-12
Glazing Requirements/Thickness No Vision Light Required TBD by Manufacturer
Blast Requirements to be provided Sample Criteria

(DoD Projects) (Door)
Product Size 3´-0˝ x 7´-0˝
Charge Weight II
Stand-off Distance 250 ft
Level of Protection Medium
UFC Revision, Revision Date, and Change Date UFC 4-010-01, 9 Feb 2012
(If Applicable) Change 1, 1 Oct 2013
3
4
Sample Blast Quote Request Form
Blast Resistant Door – Request for Quote
Door
SDI 133-16
Blast Requirements ➍ Frame ➎ Hwr ➏

Opening ➊ Door Fire Seated or Load Impulse Duration % Rebound Response Jamb Wall Lock
Qty Swing Width Height Material Type ➋ Rating ➌ Unseated (psi) (psi-ms) (ms) Response Category Width Thickness Type
1
2
3
4
5
Interior – Secure Area Material:
The doors material type (SS-Stainless Steel,
CR-Cold Rolled, GV-Galvanized)
➊ RH LH RHR LHR Width Height Hinges:
Exterior – Public Area (Key side of door) Heavy Duty S.S. Hinges 32D
Door Swing
Glass type will be specified as required to meet the blast
requirement
➋ Glass by Manufacturer
(F) Flush (V) Vision (N) Narrow Light (G) Half Glass (FG) Full Glass Glass provided by customer
➌ Fire Rating – Opening is required to withstand a fire for 1/3, 3/4, 1-1/2 or 3-hour rating.
Load – Expected loading Rebound Response – Represents the expected psi Category:
resistance as capacity the door will be required to withstand in the op- I No visible damage
generated by a blast posite direction of the blast in percent form. II Visible damage to the panel, but the
psi 0% No rebound response required. door remains operable
➍ Seated Unseated Duration – Blast duration in 50% Rebound response is ca- III Panel is damaged & inoperable, but the
Seated or Unseated is whether msec. pable of 50% of the specified door remains as a barrier
door will blast towards the door Impulse – The amount of blast load (psi) IV Door panel is severely deformed with
stop or away from the door stop, psi-msec the door will 100% Rebound response capacity openings between the door and frame,
please choose one. be exposed to. is equal to blast load. but the door remains affixed to the frame.
Jamb width – Overall width of the frame section profile Contact Person:
➎ Wall type – Wall condition the frame will be anchored to (Masonry or Challel or Tube steel) Title:
Lock Type – Panic Device, Single Point Mortise Lock or 3-Point Mortise Lock – S.S. Finish Company:
➏
Test Method: Project Name: Phone:
Revision: Project Location: E-mail:
Project Mgr: Fax:
Contact Phone: Date:
MEMBERS OF THE
Ceco
9159 Telecom Drive
ANSI/SDI A250.6 Recommended Practice for Hardware Reinforcing on Standard Steel Milan, TN 38358-3425
Doors and Frames (731) 686-8345
www.cecodoor.com
ANSI/SDI A250.8 Specifications for Standard Steel Doors and Frames (SDI-100)
Curries
1502 12th Street
SDI-128 Guidelines for Acoustical Performance of Standard Steel Doors and (641) 423-1334
www.curries.com
Frames
SDI-129 Hinge and Strike Spacing 931 S. Flores Street
SDI-133 Guideline for Specifying Steel Doors & Frames for Blast Resistance San Antonio, TX 78204-1406
(210) 226-8271
www.deansteel.com
Test Procedures
Coatings for Steel Doors and Frames Fontana, CA 92336-1638
(909) 770-5700
HOLLOW METAL XPRESS
Surfaces for Steel Doors and Frames Phoenix, AZ 85043
(623) 936-7000
ANSI/SDI A250.13 Testing and Rating of Severe Windstorm Resistant Components for www.HMXpress.com
Mesker Door, LLc
(Not applicable for FEMA 320/361 or ICC-500 Shelters) 3440 Stanwood Boulevard
SDI-113 Standard Practice for Determining the Steady-State Thermal Huntsville, AL 35811-9021
Transmittance of Steel Door and Frame Assemblies (256) 851-6670
www.meskerdoor.com
MPI
(606) 523-0173
Carlstadt, NJ 07072
(201) 933-1900
SDI-122 Installation Troubleshooting Guide for Standard Steel Doors and www.pioneerindustries.com
155 Republic Drive
(731) 352-3383
SDI-112 Zinc-Coated (Galvanized/Galvannealed) Standard Steel Doors and www.republicdoor.com
Frames
SMP
SDI-117 Manufacturing Tolerances for Standard Steel Doors and Frames An ASSA ABLOY Door Group Company
5678 Concours Street
SDI-124 Maintenance of Standard Steel Doors & Frames Ontario, CA 91764
SDI-127 Industry Alert Series (A-L) (909) 593-2100
www.secmet.com
SDI-130 Electronic Hinge Preparations
Steelcraft
SDI-134 Glossary of Terms for Hollow Metal Doors and Frames 9017 Blue Ash Road
AUDIO-VISUAL PROGRAMS ALSO AVAILABLE (513) 745-6400
www.steelcraft.com

440.899.0010 • FAX 440.892.1404
8/11/2016 www.steeldoor.org
SDI
Industry Alert 134 - 14
GLOSSARY OF TERMS
FOR HOLLOW METAL
DOORS AND FRAMES

Glossary of Terms
for Hollow Metal Doors and Frames
Definitions of terms commonly used in connection with Hollow Metal Work, defined as they apply
specifically to hollow metal, may be defined differently by other industries.
The following glossary is reprinted with permission from the Hollow Metal Manufacturers Associa-
tion’s HMMA 801-12.
ACTIVE DOOR (ACTIVE LEAF): In a pair of doors, the door or doors in

which the latching device is installed.
ACTUAL DOOR SIZE: The largest measured width by height of the

door leaf as manufactured. Equal to the nominal door size minus design
clearance. Also referred to as Net Door Size.
ADJUSTABLE BASE ANCHOR: See ADJUSTABLE FLOOR ANCHOR.
ADJUSTABLE FRAME: A frame with profile in two or more pieces to

accommodate various wall thickness. Also referred to as an expandable
frame or split frame.
ANCHOR: A metal device provided inside of a jamb, head, sill or mullion

used to secure the frame to the adjacent structure, such as wall, ceiling
or floor. Also referred to as jamb anchor, wall anchor, floor anchor, etc.
See listing;
ADJUSTABLE FLOOR: A metal device used to secure a frame

to floor at base which allows the jamb to be positioned at a
location in height above floor. Typically used at a depressed slab
or unlevel floor condition. Also referred to as Adjustable Base
Anchor.
STEEL STUD WOOD STUD
COMPRESSION: An adjustable metal device, used to secure,

adjust and square a slip on frame.
1
SDI 134-2014
EXISTING WALL: A hole preparation, generally in the soffit of

a frame member, with internal reinforcing and/or guide for an
expansion bolt, machine bolt, or screw. Used to secure the frame
to an existing opening.
FIXED FLOOR: A metal device attached to the bottom of the

frame to secure a frame to the floor. Also referred to as Base
Anchor or Sill Anchor.
MASONRY STRAP & STIRRUP: A fixed metal device

used to secure the frame to new masonry walls.
MASONRY “T”-SHAPED: A loose metal device used to secure

the frame to new masonry walls.
MASONRY WIRE: A loose metal device used to

secure the frame to new masonry walls.
MULLION: A metal clip or angle in either 1 or 2 pieces, secured

to the floor in which mullion is then positioned over.
POURED IN PLACE: A metal device used to secure a frame to

new concrete pour in place wall.
2
SDI 134-2014
SILL: A metal channel secured to the floor in which the sill

section of a hollow metal frame is positioned over.
STEEL STUD: A metal device secured in

a frame to be used for attachment to a wall
built with steel studs.
WOOD STUD: A metal device secured in a frame to be used for

attachment in a wall built with wood studs.
APPLIED STOP: A separate surface mounted channel, typically used on

a cased opening section. Creates a rabbeted frame profile.
APPLIED TRIM: A decorative piece mounted to the face of a frame or

door.
ARMOR PLATE: A plate that can be of various materials and

thicknesses applied to a door and /or frame externally, and can extend
to the full height and width of the door. Not to be confused with ballistic
resistance armor.
3
SDI 134-2014
ASTRAGAL: A component or combination of components applied to;

(a) a single door; (b) one or both doors of a pair at their meeting stiles
to cover the door edge clearance; (c) the bottom edge of the flush
transom panel; or ( d) the bottom of the top leaf of a dutch door. The
Astragal closes the clearance gap for the purpose of ensuring privacy;
minimizes the passage of light; retard the passage of air, sound, smoke
or flame; and provides additional security. Provided by the hollow metal
manufacturer, or the hardware supplier.
FLAT SURFACE: A one-piece steel strip attached to one door

and overlapping the other door when in the closed position.
INTEGRAL: Either face of a door in a pair, formed at its lock

edge to overlap the adjacent leaf.
WRAP AROUND: A formed piece of steel attached to one leaf

of a pair, and overlapping the other door when in the closed
position.
RETURN
BACKBEND: The element of the frame profile which extends from the
return and is formed parallel to the wall, inside the throat. Also referred BACKBEND
to as second return, double return or drywall return. See FRAME

ELEMENTS for additional details.
BACKSET: The distance from a cutout or datum line for a hardware

preparation from a defined datumn a door or frame.
CL
FLUSH BOLT: The distance from the centerline of the lock edge
of a door to the centerline of the bolt. Shown on beveled edge
door. CL
HINGE: On a door, the distance from the push side face sheet
to the edge of the hinge cutout. On a frame rabbet, the distance
from the stop to the edge of the hinge cutout.
4
SDI 134-2014
LOCK: The distance from the centerline of the lock edge of a

door to the centerline of the lock face prep. Shown on beveled
edge door.
STRIKE: On a frame rabbet, the distance from the stop to the

edge of the strike cutout. On the door edge, the distance from
the push side face sheet to the edge of the strike cutout.
BASE: See SILL.
BASE ANCHOR: See ANCHOR.
BASE ANCHOR EXTENSION: See FLOOR ANCHOR EXTENSION.
BELOW FLOOR: Below the top of the concrete or structural slab. See
also Jamb Extension.
BEVELED EDGE: See EDGE, BEVELED.
BLANK JAMB: See JAMB.
BLAST RESISTANT: Refers to a hollow metal assembly designed

and manufactured to resist a specified series of impulse pressures of
designated magnitude in pounds-force (Newtons).
BORROWED LIGHT: A glazed opening frame installed in an interior

partition prepared for field installation of stationary (fixed) glazing.
Mullions may be used to divide individual glazed areas. Similar to
WINDOW.
BOTTOM CHANNEL: The horizontal stiffener channel secured into the

bottom of a door. Also referred to as end channel.
5
SDI 134-2014
BULL-NOSE: See EDGE, BULL-NOSE.
BULL-NOSE TRIM: A radius shaped component applied to the vertical

door edge. A typical application would be on double acting doors.
BULLET RESISTANT: A hollow metal assembly designed and

manufactured to resist penetration by fire arms projectiles.
BUTT JOINT: Intersection of members, which are not mitered.
BUTTED FRAME: A frame which fits against a wall rather than wrap
around it.
CAMLIFT HINGE: A hinge designed and manufactured to provide lifting

of the door to a specific height as it is opened through a specific degree
of opening. Commonly used on sound retardant door.
CASED OPENING FRAME: A frame without a stop and soffit. See

FRAME PROFILE for detail.
CEILING STRUT: An adjustable member extending vertically from frame

to a rigid support above to hold the frame in place.
CENTER RAIL: See RAIL. ALT. PIPE SLEEVE
CLASSIFIED: “Products or material of a specific group category that

are constructed, inspected, tested and subsequently reinspected in
accordance with an established set of requirements.” (Taken directly from
NFPA 80.)
CLEARANCE: A term used to define a distance between two items.
FLOOR: The distance between the bottom of the door and

the top of the material directly below the door. This varies with
applications, such as concrete, any floor covering and/or a
threshold. (For additional information, see HMMA TechNote
HMMA 810-TN01-03,“Defining Undercuts”.)
6
SDI 134-2014
DESIGN: The distance around a door established by the

manufacturer, used to determine the Actual Door Size.
DOOR EDGE: The distance between either the edge of

the door and frame rabbet, or the edges of two doors of a
pair.
FRAME INSTALLATION, BUTTING WALL: The distance

between a frame and the wall construction where the frames
butts against the wall.
FRAME INSTALLATION, OVERLAPPING WALL: The distance

between the frame return or backbend to accommodate
irregularities in the thickness in the wall, when the frame is
capping the wall.
STOP: The distance between the frame stop and the face of the
door when the door is in the closed position. Typically equal to
the thickness of the silencer.
CLOSED SECTION: A frame member without a throat opening such as a

mullion or transom bar.
CLOSER REINFORCEMENT: A metal plate or channel in a door or

frame to provide additional strength for the attachment of a door closer.
Sized and located to accommodate hardware requirements.
PARALLEL ARM: Reinforcing in soffit of frame header or

transom mullion.
7
SDI 134-2014
TOP JAMB MOUNT: Reinforcing in push side face of

frame header, transom mullion, or panel.
REGULAR ARM: Reinforcing in pull side face of frame header,

transom mullion, or panel.
SLEEVE: Reinforcing inside frame header conforming to soffit,

rabbet, stop, and face.
CLOSURE CHANNEL: An additional channel section fitted between the

flanges of the top or bottom channel of a door, with its flanges projecting
inward and its web in line with the door edge.
COMMERCIAL HOLLOW METAL: Steel door and frame products

manufactured for use in office buildings, schools, hospitals, stores and
other applications. (See ANSI/NAAMM HMMA 861 Guide Specification.)
COMMERCIAL SECURITY HOLLOW METAL: Steel door and frame

products designed, tested and manufactured to resist intrusion or forced
entry in commercial applications. (See ANSI/NAAMM HMMA 862 Guide
Specification.)
COMMUNICATING FRAME: Hollow metal frame fabricated such that a

door is installed in each rabbet of a double rabbetted frame (2 doors total)
to facilitate dual access and control of the opening, i.e. hotel/motel suites,
and acoustical applications.
COMPOSITE DOOR: A door consisting of a nonmetal core bonded to a

metal facing.
CONTINUOUS WELD: See WELD.
CONTINUOUSLY WELDED: See WELDED.
CONTRA-SWING FRAME: A frame with two doors swinging in

opposite direction incorporating a fixed or removable hollow metal
mullion between the doors.
8
SDI 134-2014
CORE: The material(s) of a hollow metal door or panel.
CORNER CLIP: See REINFORCING GUSSET.
CORNER JOINT: The intersection of either the perimeter members of a

metal frame product or glass stops.
CORNER GUSSET: See REINFORCING GUSSET.
90°
CORNER POST, (CORNER MULLION): A closed section, which

facilitates a turn in the hollow metal frame assembly. The angle of the turn
may vary, although 45 degree and 90 degree turns are common.
COVER PLATE: A removable piece of metal used to cover the hardware

preparation or provide access to the interior of door or frame.
CUT-OFF STOP: The stops and soffit on a jamb or mullion at a door

opening that are terminated at a specified distance above the floor, and
are closed square or at an angle. To facilitate cleaning the floor. Also
referred to as Hospital Stops, Sanitary Base or Terminated Stop.
CUTOUT: A hole in the hollow metal door or frame to accommodate

hardware, light kits, louvers or other options.
DESIGN CLEARANCE: See CLEARANCE.
DETENTION SECURITY HOLLOW METAL: A steel door and frame

assembly designed, tested, and manufactured for the containment of
individuals to designated areas within detention or correctional facilities.
(See also ANSI/NAAMM HMMA 863 Guide Specifications.)
DOOR CLEARANCE: See CLEARANCE.
DOOR EDGE: The vertical surfaces of the door.
HINGE: The vertical edge of a door to which hinges or pivots are

attached.
LOCK: The vertical edge of a door in which locking or latching

hardware may be installed.
9
SDI 134-2014
Channel or
angle may be
DOOR EDGE SEAM: The connection of face used in place
of plate
sheets at the vertical edge.
LOCK SEAM PAN & SKIN CENTER SEAM
DOOR FACE: The exposed surface of the door not including the vertical
edges and top and bottom.
DOOR FRAME: An assembly of members surrounding and supporting a

door, or doors.
DOOR LIGHT: The provision for glazing material in a door.
DOOR OPENING: The area in a frame product into which a door or

doors are installed.
DOOR OPENING HEIGHT: The distance measured vertically between

door rabbet and the top of floor or bottom of frame minus jamb
extensions. Also referred to as nominal door height. (For additional
information, See HMMA TechNote HMMA-810 TN01-03 “Defining
Undercuts”)
DOOR OPENING WIDTH: The distance measured horizontally between

door rabbets. Also referred to as nominal door width.
DOOR RABBET: See RABBET.
DOOR REVEAL: The distance from the face of the door to the face of the
frame on the pull side.
DOOR SCHEDULE: The listing of all door openings on the project by the
Architect’s/Designer’ s mark number, including a description of each door
opening. The schedule is normally found in the drawings or specifications.
DOOR STOP: That part of a frame profile against which the door closes.
DOUBLE-ACTING DOOR: A door that swings in both directions. May

incorporate bull-nose edge[s].
DOUBLE-ACTING FRAME: A frame for double-acting doors.
10
SDI 134-2014
DOUBLE EGRESS DOORS: A pair of doors swinging in opposite

directions, located in the same plane within the frame.
DOUBLE EGRESS FRAME: A frame prepared to receive double egress.
DOUBLE RABBET: A frame provided with two rabbets. See FRAME

PROFILE for detail.
DOUBLE RETURN: See BACKBEND.
DOUBLE SWING FRAME: See PAIR FRAME.
DRIP: A head mounted molding designed to reduce rainwater infiltration

at top of door.
DRYWALL FRAME: A frame designed for installation in a wall

constructed with studs and gypsum wallboard or other dry sheet facing
material.
DRYWALL PROFILE: Description of a frame with backbends. Slip-on

frames utilize this type of profile.
DRYWALL RETURN: See BACKBEND.
DUST COVER BOX: See GROUT GUARD.
DUTCH DOOR: A door consisting of two separate leaves, one above the
other. May be provide with shelf at its top edge of the bottom leave.
DUTCH DOOR FRAME: A frame prepared for a dutch door.
11
SDI 134-2014
EDGE PROFILE: Description of the vertical door edge; beveled, bull

nosed, rabbeted, or squared, Available on lock and/or hinge edge.
⅛"
BEVELED: The vertical door edge has a 1/8˝ in 2˝ (3.1 mm in, 2"
50.8 mm) slope from a plane perpendicular to the door pull side
face.
BULL-NOSED: The vertical door edge simulates a 2-1/8˝ (54

mm) radius.
RABBETED: The vertical door edge which overlaps another

door or frame.
SQUARED: The vertical door edge that is formed 90 degree to 90°

the face of the door.
EDGE SEAM: The connection of the face sheet at the vertical edge.
ELEVATION: An orthographic projection of the vertical side of a hollow

metal assembly (doors, frames, etc.) usually shown on the architectural
plans in conjunction with the vertical side view of a building wall.
EMBOSSED: Having a raised and/or indented pattern impressed on a

surface by means of patterned rolls or stamping dies.
END CHANNEL: See TOP CHANNEL and BOTTOM CHANNEL.
EXISTING WALL ANCHORS: See ANCHORS
EXPANDABLE FRAME: See ADJUSTABLE FRAME.
FACE WELDED: See WELDED.
FIELD SPLICE: A connection of hollow metal frame components

accomplished in the field. Also referred to as Shipping Splice.
FILLER PLATE: A metal plate used to fill unused mortise cutouts in a

door or frame.
12
SDI 134-2014
FINISHED FLOOR: See FLOOR.
FIRE ENDURANCE RATING: See FIRE RATING.
FIRE PROTECTION RATING: See FIRE RATING.
FIRE-RATED: A product which has successfully met all conditions of

acceptance of the fire test standard specified in the governing model
or building code, is “Listed” or “Classified” and eligible for labeling by a
recognized testing agency having a factory inspection service.
FIRE RATING: A numeric designation indicating the duration of fire test

exposure to which a product has been exposed, and successfully met
all acceptance criteria of the standard to which it is tested. For swinging
doors and frame products, typical fire ratings include 3, 1-1/2, 1, 3/4, and
1/3 hour. Also called Fire Protection Rating.
FIXED STOP: See STOP
FLOOR: The top of the concrete or structural slab. Also referred to as

finished floor. (For additional information, see HMMA TechNote HMMA-
810 TN01-03 “Defining Undercut.”)
FLOOR ANCHOR: See ANCHOR
FLOOR CLEARANCE: See CLEARANCE.
FLOOR COVERING: Any material applied on top of the floor. (For

additional information, see HMMA TechNote HMMA-810 TN01-03,
“Defining Undercuts”)
FLOOR STILT: A metal device attached to the jamb of a door frame to

hold the frame above the finished floor. ABOVE
FLOOR
FLUSH DOOR: A door having no glass lights, panels, louvers or grilles.
FRAME: See DOOR FRAME.
FRAME CLEARANCE: See CLEARANCE.

13
SDI 134-2014
FRAME FACE: The elements of a frame profile which is visual on the

vertical side of a hollow metal assembly. See FRAME ELEMENTS for
details.
STOP
RETURN
RABBET
FRAME ELEMENTS: Within a Frame profile, a specific part such as;
soffit, stop, rabbets, faces and returns. (For additional information, see BACKBEND
HMMA TechNote HMMA-820 TN 02-03,“Continuously Welded Frame”.) SOFFIT
RABBET
FRAME GASKET: See GASKETING. FACE
FRAME JOINT: The intersection of two or more frame members.
HEAD
JAMB
FRAME MEMBER: A component in a frame product such as a jamb,

MULLIONS
head, mullion or sill. (For additional information, see HMMA TechNote
JAMB
HMMA-820 TN 02-03, “Continuously Welded Frame”.)
SILL
FRAME PROFILE: Visual description of a frame member. Typically

referred to as cased opening, single rabbet, double rabbet, and double
egress. Refer to individual description for detail.
RABBET
RABBET
RABBET
RABBET
CASED OPENING SINGLE RABBET DOUBLE EGRESS DOUBLE RABBET
FRAME PRODUCTS: Used to describe, as a group, “Frames”, “Transom

Frames”, “Sidelight Frames” and “Window Frames”.
FRAME SECTION: Cross cut of a frame member. See FRAME

PROFILE.
FRAME SILL: The bottom horizontal member of a sidelight or borrowed

light frame. Also referred to as Base.
14
SDI 134-2014
FULL PROFILE WELDED: See WELDED
FULL (FULLY) WELDED: See WELDED.
FULL (FULLY) WELDED FRAME: See WELDED.
FULLY WELDED SEAMLESS DOOR: See WELDED.
GAGE (GAUGE): An numeric value used to define the nominal thickness

of material. (See NAAMM/HMMA 803-08 “STEEL TABLES”.)
GASKETING: Material applied around the door or frame to close the

clearance opening and minimize or restrict the passage of smoke, light,
sound or weather.
GLAZING: The process of installing glazing materials.
GLAZING (GLASS) BEAD: A removable formed metal section used to

secure glazing or panel in a door or frame.
GLAZED, (GLASS) LIGHT: In a frame, the light is formed by the

assembly of jamb, head, sill and mullion members into a rectangular or
shaped opening. The light is equipped with factory installed glazing bead
used to retain the glazing that is installed by the glazing contractor. In a
door, the light is formed by providing a rectangular or shaped cutout in
the door and equipping it with molding and removable bead to receive the
glazing.
GLAZING, (GLASS) MOLDING: The portion of the assembly retaining

glazing materials or in-fill panels in a hollow metal door which contain the
integral stop, and to which a glazing bead is attached. Also referred to as
Glazing Stop.
GLAZING MATERIAL: A transparent or translucent material used in door

assemblies and windows.
GLAZING STOP: See GLAZING, (GLASS) MOLDING
GROUT: A substance used to fill up voids in hollow metal frame cavities.

(For additional information SeeNAAMM/HMMA 820 TN1-03 Technical
Note “Grouting”.)
15
SDI 134-2014
GROUT GUARD: A metal cover attached to a frame behind

reinforcement for mortised or recessed hardware items, to prevent grout
from entering the mounting holes. Also referred to as Dust Cover Guard,
Masonry Guard, Mortar Guard, or Plaster Guard.
GROUTED FRAME: Frame filled with grout.
HANDING: A term used to designate the direction of door swing.
HARDWARE SCHEDULE: Complete listing of all hardware specified

for a project, organized by opening numbers including Door Headings,
manufacturers names, template numbers, and special hardware
locations. Prepared in accordance with industry standards for or by the
Architect/Designer and issued for bid. Once contract is awarded and
Hardware Schedule is approved, it becomes part of construction contract.
HARDWARE TEMPLATE: A detailed drawing of the hardware

preparation provided by hardware manufacturing for providing preparation
of hardware.
HEAD, (HEADER): The horizontal member which forms the top of a

frame.
HEAD STIFFENER: A metal angle or channel attached inside the head

of a door. Not to be used as a load-carrying member.
HINGE JAMB: See JAMB.
HINGE REINFORCEMENT: A metal plate or angle attached to a door or

frame to which a hinge is attached.
HINGE SIDE: See PULL SIDE:
HOLLOW METAL: A term used to reference to doors, frames, partitions,

enclosures and other items, fabricated from metal sheet.
HOSPITAL PROFILE: See SPLADE STOP.
HOSPITAL STOP: See CUT-OFF STOP.
INACTIVE DOOR or LEAF: The leaf of a pair of doors which does not
contain a lock but is secured, when closed, by top and/or bottom bolts
and contains a strike to receive the latch or bolt of the active leaf.
16
SDI 134-2014
INFILL PANEL: See PANEL, INFILL.
INTEGRAL ASTRAGAL: See ASTRAGAL.
INTEGRAL STOP: See STOP, INTEGRAL.
INTERGAL TAB and SLOT: Formed as part of the frame profile used
to align machined mitered frame comer joints in mechanical alignment
construction.
INTERLOCKING SEAM: See LOCK SEAM DOOR.
JAMB: The vertical frame member forming the perimeter of a frame.
BLANK: A jamb without mortised hardware preparation.
HINGE: A jamb of a frame prepared for hinges or pivots.
STRIKE: A jamb prepared for a strike.
JAMB ANCHOR: See ANCHOR.
JAMB DEPTH
JAMB DEPTH / JAMB WIDTH: The dimension of a frame member OR
JAMB WIDTH
measured perpendicular to the face from one face to the other.
JAMB EXTENSION: That portion of a jamb which extends below the

level of the floor. See Also BELOW FLOOR. (For additional information,
see HMMA TechNote HMMA-810 TN01-03,“Defining Undercuts.”)
JAMB OPENING: See DOOR OPENING, WIDTH.
JAMB WIDTH: See JAMB DEPTH.
KERFED FRAME: A frame that is formed with an integral pocket or

recess in the area of the stop to receive gasket or seals.
KNOCKED DOWN: A frame product that is shipped disassembled,

commonly abbreviated “KD.”
17
SDI 134-2014
LABEL: A metal plate, sticker, or embossment, on a product to indicate a

performance level in accordance with a specific standard.
LAMINATED CORE: A door or panel construction utilizing; kraft

honeycomb, rigid foam, mineral core or steel stiffeners, in which steel
face sheets are bonded.
LEADING EDGE: Intersection of the lock edge and the pull side face of a
door.
LEAD-LINED: A door or frame, which is lined with lead to prevent

radiation penetration.
LEAF: A single door.
LEAVES: More than one door.
LOCK CENTER CLIP: A part to position a mortised lock inside the

center of a door.
LOCK EDGE: See DOOR EDGE.
LOCK REINFORCEMENT: A plate attached inside of a door to which a

lock is fastened.
LOCK SEAM: Interlocking construction of a door or panel edge.
LOUVER: A series of slats, blades, or piercings to allow passage of air LOCK SEAM
through an opening.
LOUVER INSERT: A louver that is fabricated separately and inserted into

a preparation in the door or frame.
MASONRY GUARD: See GROUT GUARD.
MEETING STILE: The vertical edge of a door, in a pair, which is adjacent

to the other door.
MITER JOINT: The intersection of frame members, (typically head and

jambs) or frame elements (stops) in which the faces meet at an angle.
18
SDI 134-2014
MORTAR: See GROUT.
MORTAR GUARD: See GROUT GUARD.
MORTISE: A recess on a minimum of 3 sides of a hardware item closely

surrounding the contour of the item allowing its faceplate to finish flush
with the door or frame finished surface.
MORTISE PREPARATION: For hardware, a cutout recessed into a door

or frame, which may include, drilling and tapping.
RABBET
MULLION: A closed member within a frame, separating doors, a

door and sidelights, glazed areas or panels. A mullion may be fixed
or removable. Typically a double or single rabbeted profile. RABBET
MUNTIN: A bar or formed material supporting and separating panes of

glass within a door, sidelight, transom, borrowed light, or window frame.
MUTE: See SILENCER.
NAILING FLANGE: A reveal flange in which nail holes are provided.
NARROW SIDE OF DOOR: See PUSH SIDE OF DOOR.
NET DOOR SIZE: See ACTUAL DOOR SIZE.
NOMINAL DOOR HEIGHT: See DOOR OPENING HEIGHT.
NOMINAL DOOR SIZE: (Door opening width) by (door opening height).
NOMINAL DOOR WIDTH: See DOOR OPENING WIDTH.
OPENING SIZE: The frame opening measured between the rabbets

horizontally and between the header, rabbet and bottom of frame
vertically.
OPERABLE TRANSOM: Panel or glass lite above door opening which

may be opened for ventilation purposes.
19
SDI 134-2014
OVERLAPPING ASTRAGAL: See ASTRAGAL, FLAT SURFACE.
PANEL, HOLLOW METAL: An assembly made of the same material and

construction as a door.
PANEL, INFILL: An assembly comprised of steel sheet secured to each

face of a backing material (gypsum or cement board, etc.), installed like
glazing materials, in doors, transom, sidelight and window assemblies.
PERIMETER FRAME JOINT: The intersection of two or more frame

members that are accessible through the throat or from the unexposed
side of the frame member. (For additional information, See HMMA
TechNote HMMA-820 TN02-03,“Continuously Welded Frames.”)
PLANKING: Wood spacers used in storage of doors and frames.
PLASTER GUARD: See GROUT GUARD:
PLINTH: A section of sheet metal, usually stainless steel, used as a base PLINTH
for a door frame at the floor. It has the same thickness and profile as the
jamb section, and is flush with the jamb on all surfaces.
POCKET DOOR: A door designed to slide/recess into a wall cavity

to open, and slide out of the wall cavity to close.
JAMB WIDTH
POCKET DOOR FRAME: Frame designed to allow a door to slide

inside a pocket located within the cavity of a wall.
PRESSURE RESISTANT: Refers to a hollow metal assembly designed

and manufactured to resist uniform static pressure of a specified
magnitude over its exposed surface.
PRIMER / PRIME PAINT: Paint coating used as a base for finish paint.
PULL SIDE OF DOOR: The face of a door opposite the frame stops. Also
referred to as Hinge Side or Wide Side.
PUSH SIDE OF DOOR: The face of door, which contacts the frame
stops. Also referred to as stop side or narrow side.
20
SDI 134-2014
RABBET: On a frame, the area that is between the stop and the face,
capable of accepting doors, panels or glazing materials. Also referred to
as Door Rabbet. See FRAME ELEMENT for detail.
RABBETED: Description of a door edge formed to interlock with another

door, frame or panel.
TOP RAIL
RADIATION SHIELDING: Refers to a hollow metal assembly designed
and manufactured to resist penetration by a specified type of radiation.
CENTER RAIL
RAIL: The horizontal member forming the top or bottom edge of a

door, or separating panels or glazed areas. Referred to as Top Rail,
Intermediate Rail or Bottom Rail.
BOTTOM RAIL
REINFORCING GUSSETT: A flat or formed component at junction of

head and jamb used in interlocking of knock-down (KD) frames. May be
used as an alignment feature on punch mitered frames.
REMOVABLE MULLION: A frame member designed for temporary

removal. See MULLION for detail.
REMOVABLE STOP: See STOP
RETURN: The element of the frame profile, which extends inward from RETURN
the face to the throat.
REVEAL FLANGE: The element of the frame profile, which extends from REVEAL
FLANGE
the return. Typically formed parallel to the wall.
REVEAL
REVEAL RETURN: The element of the frame profile, which extends from RETURN
the reveal flange.
REVERSE BEVEL: Refers to hand of door or lock on outswing doors.
21
SDI 134-2014
RIB: See STIFFENER.
ROUGH BUCK FRAME: An assembly which consists of a finished

frame and anchoring channels.
ROUGH OPENING: The size of the wall opening into which a frame is to
be installed.
SANITARY BASE: See CUT-OFF STOP.
SEAM, INTERLOCKING: See LOCKSEAM.
SEAMLESS DOOR: A door having no visible seams on its faces or

edges.
SHIPPING BAR: See SPREADER.
SHIPPING SPLICE: See FIELD SPLICE.
SIDELIGHT: A framed area immediately aside a door opening which may

contain fixed glazing, panel or other filler.
SILENCER: A of resilient material attached to the stop on a frame to

cushion the closing of a door. Also referred to as Mute.
SILL ANCHOR: See ANCHOR.
SILL: The bottom horizontal member of a sidelight or borrowed light

frame. Also referred to as Base.
SINGLE-ACTING DOOR: A door which only opens in one direction.
SINGLE RABBET FRAME: A frame having only one rabbet See FRAME
PROFILE, for detail.
SLIP-ON FRAME: Frame designed to be installed after the wall is

erected.
22
SDI 134-2014
SMOKE CONTROL ASSEMBLY: A door and frame assembly with

gasketing (by others) designed to resist the passage of smoke when the
door is in the closed position. May or may not be Fire-Rated.
SOFFIT: The element of a door frame; (a) between the stops on a double
rabbeted frame, (b) between the stop and face opposite door side of a
single rabbeted frame. See FRAME ELEMENT for detail.
SOUND RETARDANT: A characteristic of a hollow metal assembly

designed and manufactured to resist sound transmission. The Sound
Transmission Classification (STC) rating of the assembly indicates the
level of resistance to sound transmission.
SPAT: A protective covering, usually of stainless steel, applied over the SPAT
bottom of jambs to facilitate cleaning and reduce frame damage.
SPLADE PROFILE: A frame member where the transition from stop to

opposite face is sloped. Also referred to as Hospital or sloped Profile.
RABBET
SPLIT FRAME: See ADJUSTABLE FRAME.
SPOT WELD: See WELDING.
SPREADER (SPREADER BAR): A metal channel or angle temporarily

attached to the base of a door frame, extending between jambs, to keep
the frame in proper alignment during shipping and handling.
SQUARE-EDGE DOOR: A door having vertical edges that are

perpendicular to its face. See EDGE PROFILE for detail.
STEEL STUD ANCHOR: See ANCHOR.
STIFFENER: An internal formed steel component used to strengthen a

door panel or frame member.
23
SDI 134-2014
STILE STILE
STILE: The vertical member which form the edge of a door.
STOP: An element of a frame profile. See also Door Stop and

Glazing (Glass) bead. See FRAME ELEMENT for detail.
INTEGRAL: A stop, which is formed as part of the frame profile.
REMOVABLE: Metal channel or angle which is removable to

allow installation of glass, panel or door.
STOP SIDE: See PUSH SIDE OF DOOR.
STRIKE JAMB: See JAMB.
STRIKE REINFORCEMENT: A metal plate or formed unit attached inside

a door or frame to attach a strike.
STRUT: See CEILING STRUT.
SUB-BUCK or SUB-FRAME: See ROUGH BUCK FRAME.
SURFACE HARDWARE REINFORCEMENT: A metal plate attached

inside a door or frame to receive surface-mounted hardware applied in
the field.
SWING: A term used to describe the operation of a hinged door.
SWINGING DOOR: A door mounted on hinges or pivots.
TEMPERATURE RISE RATED DOOR: A fire rated door designed to limit

the transfer of heat over a specified duration to a specified temperature.
TERMINATED STOP: See CUT-OFF STOP, also called Hospital Stops.
24
SDI 134-2014
THERMAL BOW: A temporary condition, affecting the operation of

an exterior door due to the inside temperature differential. The extent
of this condition will vary with environmental conditions, door color,
door construction, length of exposure, etc. This condition can often be
alleviated by painting the outside surface of the door a light color.
THROAT: The distance between Returns or Backbend Returns of a THROAT

frame profile.
TOLERANCE: Permissible deviation from a nominal or specified

dimension or value.
TOP CHANNEL: Horizontal stiffener channel secured into the top of a

door. Also referred to as End Channel.
TOP RAIL: See RAIL:
TRANSOM: A framed area immediately above a door opening which may

containing fixed glazing, an operating sash, panel or other filler.
TRANSOM BAR: See TRANSOM MULLION.
TRANSOM FRAME: A frame containing a door opening and transom

with or without a transom mullion.
TRANSOM MULLION: The horizontal frame member, which separates

the door opening from the transom. Also referred to as transom bar.
TRIM: See FRAME FACE.
UNDERCUT: The Distance between the bottom of door and the

bottom of the frame. (See NAAMM/HMMA 810 TN01-03 Technical Note
“Determining Undercuts”.)
VISION LIGHT: A glazed opening in a door.
WEEPHOLE: A opening provided to permit the drainage of moisture.
25
SDI 134-2014
WELD/WELDING: A process for the joining of metal parts, with the

necessary heat being provided by an electric arc struck between an
electrode and the metal or between two electrodes.
WELD, CONTINUOUS: A weld having no gaps or PUNCH MITERED SAW MITERED
spaces, over its entire length.
WELDED CONTINUOUSLY, DOOR: A door having

all joints on its vertical edge continuously welded and
finished smooth.
WELDED CONTINUOUSLY, FRAME: Also called

Full or Fully Welded and/or Full Profile Welded.
Comer/Perimeter joints shall have all elements of
the frame member continuously welded: soffits,
stops, rabbet, faces and returns. (See NAAMM/
HMMA 820 TN2-03 Technical Note “Continuously
Welded Frames” for additional information.)
WELDED, FACE, FRAME: Comer/perimeter joints shall have a

continuous weld at the faces only.
WICKET DOOR: A swinging door within a door.
WIDE SIDE: See PULL SIDE.
WINDOW: A glazed opening frame installed in an exterior wall prepared

for field installation stationary (fixed) glazing. Mullions may be used to
divide individual glazed areas. Similar to BORROWED LIGHT.
WOOD STUD ANCHOR: See ANCHOR
WRAP-AROUND FRAME: A frame which fits over the wall. The frame
throat is nominal 1/8˝ (3mm) larger than the wall thickness.
26
MEMBERS OF THE
Ceco Door
Milan, TN 38358
Curries
www.deansteel.com
Test Procedures
(909) 770-5700
HOLLOW METAL XPRESS
623-936-7000
www.meskerdoor.com
Corbin, KY 40701
155 Republic Drive
www.secmet.com
9017 Blue Ash Road
(513) 745-6400

440.899.0010 • FAX 440.892.1404
12/4/2014
www.steeldoor.org
ANSI/SDI A250.3-2007 (R2011)
Revision of ANSI A250.3-1999
Test Procedure and Acceptance Criteria for —

Factory Applied Finish Coatings
ANSI/SDI A250.3-2007
STEEL
DOOR
INSTITUTE
:765:69
:[LLS+VVY0UZ[P[\[L
(WWYV]LK-LIY\HY`
ANSI/SDI ®
A250.3-2007 (R2011)
Revision of
American National Standard
Test Procedure and Acceptance Criteria for

Factory Applied Finish Coatings
Secretariat
Approved February 12, 2007

American National Standards Institute, Inc.
American Approval of an American National Standard requires verification by ANSl
that the requirements for due process, consensus, and other criteria for
National approval have been met by the standards developer.
Standard Consensus is established when, in the judgement of the ANSl Board of

Standards Review, substantial agreement has been reached by directly
and materially affected interests. Substantial agreement means much more
than a simple majority, but not necessarily unanimity. Consensus requires
that all views and objections be considered, and that a concerted effort
be made toward their resolution.
The use of American National Standards is completely voluntary; their exis-
tence does not in any respect preclude anyone, whether they have approved
the standards or not, from manufacturing, marketing, purchasing, or using
products, processes, or procedures not conforming to the standards.
The American National Standards Institute does not develop standards and
will in no circumstances give any interpretation of any American National
Standard. Moreover, no person shall have the right or authority to issue
an interpretation of an American National Standard in the name of the
American National Standards Institute. Requests for interpretations should
be addressed to the secretariat or sponsor whose name appears on the
title page of this standard.
CAUTION NOTICE: This American National Standard may be revised or
withdrawn at any time. The procedures of the American National Stan-
dards Institute require that action be taken periodically to reaffirm, revise,
or withdraw this standard. Purchasers of American National Standards
may receive current information on all standards by calling or writing the
American National Standards Institute.
Published by

30200 Detroit Road, Cleveland, Ohio 44145-1967
Copyright © 2012 by Steel Door Institute

All rights reserved.
No part of this publication may be reproduced in any

form, in an electronic retrieval system or otherwise,
without prior written permission of the publisher.
Printed in the United States of America
Contents
Page
Foreword ............................................................................................ ii
1 General .........................................................................................1
1.1 Scope .....................................................................................1
1.2 Reference Documents .............................................................1
2 Material .........................................................................................1
3 Testing ..........................................................................................2
3.1 Salt spray test .........................................................................2
3.2 Condensation testing (humidity)...............................................2
3.3 Accelerated weathering test ....................................................2
3.4 Impact test ..............................................................................2
3.5 Film adhesion test ...................................................................2
3.6 Abrasion test ...........................................................................2
4 Acceptance criteria .......................................................................2
4.1 Salt spray resistance ...............................................................2
4.2 Condensation resistance .........................................................3
4.3 Accelerated weathering resistance ..........................................3
4.4 Impact test ..............................................................................3
4.5 Film adhesion ..........................................................................3
4.6 Abrasion resistance .................................................................3
5 Report ...........................................................................................3
6 General .........................................................................................3
6.1 Testing laboratory ....................................................................3
6.2 Certification .............................................................................3
Tables
1 Rust grades ..................................................................................4
2 Classification of adhesive test results ...........................................8
Figures
1 Visual reference for percentage of rust ..........................................4
2 Blister size #2 ..............................................................................5
3 Blister size #4 ..............................................................................5
4 Blister size #6 ..............................................................................6
5 Blister size #8 ..............................................................................6
6 Photographic reference standard for degree of chalking ..............7
i
Foreword (This Foreword is not part of American National Standard A250.3-2007)
The material contained in this document has been developed under the
auspices of the Technical Committee of the Steel Door Institute.
The original standard was issued on July 28, 1980 and was last revised
in 1999. The current edition is a revision of the 1999 document with the
contents being updated to reflect changes and advances that have taken
place in the steel door and frame industry since that time.
Suggestions for improvement gained in the use of this standard will be
welcome. They should be sent to the Steel Door Institute, 30200 Detroit
Road, Cleveland, Ohio 44145-1967.
The organizations that have approved this standard are as follows:
American Institute of Architects
Builders Hardware Manufacturers’ Association
Canadian Steel Door Manufacturers’ Association
Door and Hardware Institute
FM Approvals
General Services Administration
Hollow Metal Manufacturers’ Association / Division of National Association
of Architectural Metal Manufacturers’ Association
International Conference of Building Officials
Intertek Testing Services
Manufactured Housing Institute
National Association of Home Builders
Underwriters Laboratories Inc.
Window and Door Manufacturers’ Association
ii
The Accredited Standards Committee A250 TC-1 developed this standard
and had the following personnel at the time of approval:
Robert M. Berhinig, Chairman

J. Jeffery Wherry, Secretary
Organization Represented Name of Representative
American Institute of Architects ................................................. Joseph Berchenko
Amweld Building Products LLC ................................................. Mike Kolovich
Benchmark Commercial Doors .................................................. TBD
Builders Hardware Manufacturers’ Association ......................... Mike Tierney
Canadian Steel Door Manufacturers’ Association ..................... Bud Bulley
Ceco Door Products................................................................... Thomas R. Janicak
Curries Company ....................................................................... Dave Dedic
Deansteel Manufacturing Company ........................................... Claus D. Heide
Door and Hardware Institute ...................................................... John Geniesse
FM Approvals ............................................................................. Mark Tyrol
General Services Administration ................................................ Stuart Palmer
Hollow Metal Manufacturers’ Association / Division of
National Association of Architectural Metal Manufacturers ....... Russell Tauscher
Ingersoll-Rand ............................................................................ Kurt Roeper
0U[LYUH[PVUHS*VUMLYLUJLVM)\PSKPUN6MÄJPHSZ ............................ Paul Armstrong
Intertek Testing Services ............................................................ Nancy Kokesh
The Kewanee Corporation.......................................................... Fred L. Pipin
Manufactured Housing Institute ................................................. Mark Nunn
Mesker Door, Inc. ....................................................................... Mike Torres
National Association of Home Builders ...................................... Jeff Inks
Pioneer Industries....................................................................... Mitchell Dorf
Republic ..................................................................................... Jason Lisewski
Security Metal Products Corporation ......................................... Daniel Buffenbarger
Steel Door Institute ..................................................................... J. Jeffery Wherry
Underwriters Laboratories Inc. ................................................... Matthew Schumann
Window & Door Manufacturers’ Association.............................. Rick Perry
General Interest Representatives ............................................... Allan Ashachik
Stan L. Horsfall
iii
(4,90*(55(;065(3:;(5+(9+ (5:0:+0(
(TLYPJHU5H[PVUHS:[HUKHYK
;LZ[7YVJLK\YLHUK(JJLW[HUJL*YP[LYPHMVY·
-HJ[VY`(WWSPLK-PUPZO*VH[PUNZ
MVY:[LLS+VVYZHUK-YHTLZ
.LULYHS (:;4 + ¸:[HUKHYK ;LZ[ 4L[OVK MVY

,]HS\H[PUN +LNYLL VM )SPZ[LYPUN VM 7HPU[Z¹
:JVWL
(:;4 + ¸:[HUKHYK ;LZ[ 4L[OVK MVY
;OLZLTL[OVKZWYLZJYPIL[OLWYVJLK\YLZ[VIL ,]HS\H[PUN+LNYLLVM*OHSRPUNVM,_[LYPVY7HPU[
MVSSV^LKPU[OLZLSLJ[PVUVMTH[LYPHSJOLTPJHS -PSTZ¹
WYLWHYH[PVU JVH[PUN HWWSPJH[PVU [LZ[PUN HUK
L]HS\H[PVU VM MHJ[VY` HWWSPLK MPUPZO JVH[PUNZ (:;4+ ¸:[HUKHYK;LZ[4L[OVK
MVYZ[LLSKVVYZHUKMYHTLZ*VH[PUNZJV]LYLK MVY :WLJ\SHY .SVZZ¹
I` [OPZ Z[HUKHYK PUJS\KL WHPU[Z Z[HPUZ JSLHY (:;4 +L ¸:[HUKHYK 7YHJ[PJL MVY
JVH[Z HUK WV^KLY JVH[Z *HSJ\SH[PVUVM*VSVY;VSLYHUJLZHUK*VSVY+PM
9LMLYLUJL +VJ\TLU[Z MLYLUJLZ MYVT 0UZ[Y\TLU[HSS` 4LHZ\YLK *VSVY
*VVYKPUH[LZ¹
(:;4)¸:[HUKHYK7YHJ[PJLMVY6WLYH[
PUN :HS[ :WYH` -VN ;LZ[PUN (WWHYH[\Z¹ 4H[LYPHS
(:;4 + ¸:[HUKHYK ;LZ[ 4L[OVK MVY ;OL[LZ[ZWLJPTLUZOHSSIL[OLL_HJ[[`WL
,]HS\H[PVU VM 7HPU[LK VY *VH[LK :WLJPTLUZ HUKNH\NLVMZ[LLSHZ\ZLKPU[OLTHU\MHJ[\YLVM
:\IQLJ[LK [V *VYYVZP]L ,U]PYVUTLU[Z¹ [OLWYVK\J[;OLZWLJPTLUZOHSSILHTPUPT\T
(:;4+ ¸:[HUKHYK7YHJ[PJLMVY;LZ[PUN VM TTí TT^P[OH¼ TT
>H[LY9LZPZ[HUJLVM*VH[PUNZ<ZPUN*VU[YVSSLK OVSLH[[OLJLU[LYVM[OL TT^PK[O½
*VUKLUZH[PVU¹ TTPUMYVT[OLLUK0KLU[PMPJH[PVUTHYRZ
ZOHSSILHKKLK[V[OLZWLJPTLUHZYLX\PYLKMVY
(:;4 . ¸:[HUKHYK 7YHJ[PJL MVY 6W JVU[YVS W\YWVZLZ ;OL [LZ[ ZWLJPTLU ZOHSS IL
LYH[PUN -S\VYLZJLU[ 3PNO[ (WWHYH[\Z MVY <= OHUKSLKH[HSSZ[HNLZVM[OLWYVJLZZ^P[OJSLHU
,_WVZ\YL VM 5VUTL[HSSPJ 4H[LYPHSZ¹ NSV]LZ [V WYL]LU[ JVU[HTPUH[PVU
(:;4+¸:[HUKHYK7YHJ[PJLMVY-S\V ;OL ZWLJPTLUZ ZOHSS IL O\UN \ZPUN H
YLZJLU[ <=*VUKLUZH[PVU ,_WVZ\YLZ VM 7HPU[ TL[OVK YLWYLZLU[H[P]L VM [OH[ \ZLK PU WYV
HUK 9LSH[LK *VH[PUNZ¹ K\J[PVU
(:;4+ ¸:[HUKHYK;LZ[4L[OVK ;OL [LZ[ ZWLJPTLUZ ZOHSS IL JSLHULK
MVY9LZPZ[HUJLVM6YNHUPJ*VH[PUNZ[V[OL,M WYL[YLH[LKHUKJVH[LKPUHJJVYKHUJL^P[O[OL
MLJ[Z VM 9HWPK +LMVYTH[PVU 0TWHJ[¹ THU\MHJ[\YLYZUVYTHSWYVK\J[PVUTL[OVKHUK
(:;4 + ¸:[HUKHYK ;LZ[ 4L[OVK MVY WYVJLK\YL (SS JVH[PUN ^LPNO[Z \ZLK VU [LZ[
4LHZ\YPUN (KOLZPVU I` [OL ;HWL ;LZ[¹ ZWLJPTLUZZOHSSILKVJ\TLU[LKHUKYLWYLZLU
[H[P]L VM [OL PUKP]PK\HS THU\MHJ[\YLY»Z UVYTHS
(:;4 + ¸:[HUKHYK ;LZ[ 4L[OVK MVY WYVK\J[PVU TH[LYPHS
(IYHZPVU 9LZPZ[HUJL VM 6YNHUPJ *VH[PUNZ I`
[OL ;HILY (IYHZLY¹ ([ [OL LUK VM [OL JVH[PUN J`JSL [OL
ZWLJPTLUZ ZOHSS IL YLTV]LK MYVT [OL JVH[
(:;4 + ¸:[HUKHYK ;LZ[ 4L[OVK MVY
PUNZ`Z[LTHUKOHUKSLKJHYLM\SS`;OLJVH[LK
,]HS\H[PUN+LNYLLVM9\Z[PUNVU7HPU[LK:[LLS
:\YMHJLZ¹ Z\YMHJLVM[OLZWLJPTLUZOHSSUV[ILOHUKSLK

or come in contact with other objects in such UV-Condensation Exposures of Paint and Re-
a way as to disrupt the coated surface. lated Coatings” For a test period of 300 hours
duration. The cycle schedule for operating this
2.5 Specimens shall be allowed to age at an am-
type of equipment shall be 18 hours of light
bient room temperature, for a minimum 72 hour
exposure at 140°F (60°C) followed by a 6 hour
duration, before any testing commences.
condensation cycle at 120°F (49°C).
3 Testing 3.4 Impact test
3.1 Salt spray test The coating shall be tested per ASTM D2794-
93(2004), “Standard Test Method for Resistance
a) Apparatus – The apparatus used for salt
of Organic Coatings to the Effects of Rapid
spray testing shall be of such design as to
Deformation (Impact),” with 20 inch pounds of
conform to ASTM B117-03, “Standard Practice
direct impact using a Gardner Impact Tester with
for Operating Salt Spray (Fog) Testing Appa-
a ½" (12.7 mm) diameter ball or punch at room
ratus.”
temperature of 70°-75°F (21°C-24°C). The test
b) Test performance – Salt spray testing shall specimen shall be impacted at three locations
be conducted as specified in ASTM B117-03, on the panel that have a dry film thickness within
“Standard Practice for Operating Salt Spray the tolerance range for the coating process.
(Fog) Testing Apparatus,” for a test period of Apply one-inch (25.4 mm) wide, #600 Scotch
120 continuous hours. The test specimen shall cellophane pressure-sensitive tape firmly to the
be scribed with an “X” per ASTM D1654-92, impact area and pull off sharply.
“Standard Test Method for Evaluation of Painted
3.5 Film adhesion test
or Coated Specimens Subjected to Corrosive
Environments”, sections 4.1 and 5.1. The coating film adhesion shall be tested in ac-
cordance with method “B” of ASTM D3359-02,
3.2 Condensation testing (humidity)
“Standard Test Method for Measuring Adhe-
a) Apparatus – The apparatus used for con- sion by the Tape Test.” A total of (11) parallel
densation (humidity) testing shall be of such cuts are made with a sharp instrument, 0.039"
design as to conform to ASTM D4585-99, (1 mm) apart in both a vertical and horizontal
“Standard Practice for Testing Water Resis- direction forming a grid. One-inch (25.4 mm)
tance of Coatings Using Controlled Condensa- wide #600 Scotch cellophane pressure-sensi-
tion.” tive tape is then firmly applied to the scribed
surface and rapidly removed.
b) Test performance – Condensation (humid-
ity) testing shall be conducted as specified 3.6 Abrasion test
in ASTM D4585-99, “Standard Practice for
The coating film shall be tested with a Taber
Testing Water Resistance of Coatings Using
Abraser Testing Apparatus using a No. CS-10
Controlled Condensation,” for a test period of
Resilient Calibrase Wheel in accordance with
480 continuous hours. Exposure temperatures
ASTM D4060-01, “Standard Test Method for
shall be maintained at a minimum of 100°F
Abrasion Resistance of Organic Coatings by
(38°C). Actual test temperature shall be noted
the Taber Abraser.”
in the report.
3.3 Accelerated weathering test 4 Acceptance criteria
a) Apparatus – The apparatus used for ac- 4.1 Salt spray resistance
celerated weathering testing shall be of such
The coating film on the unscored surface of
design as to conform to ASTM G154-04,
the test specimen shall have a rust grade of
“Standard Practice for Operating Fluorescent
no less than 6 as defined in ASTM D610-01,
Light Apparatus for UV Exposure of Nonmetal-
“Standard Test Method for Evaluating Degree
lic Materials.” The bulb type used shall be a
of Rusting on Painted Steel Surfaces.” Table 1
UVA340.
and the depictions shown in Figure 1 illustrate
b) Test performance – Accelerated weathering the scale used to evaluate the rust grades.
testing shall be conducted as specified in ASTM The coating film at the scribe line shall not be
D4587-01, “Standard Practice for Fluorescent undercut by rust more than ⅛" (3.2 mm) or a
2
6 on each side of the scribe line when evalu- grade represents a film removal of between
ated in accordance with ASTM D1654-92 and 5 and 15%. Table 2 on page 8 illustrates the
rated per ASTM D1654-92, Table 1. “Rating of various classifications for adhesion loss.
Failure at Scribe (Procedure A)”.
4.6 Abrasion resistance
4.2 Condensation resistance
The coating film shall have a wear index of
The coating film shall be allowed to exhibit the 100 (.10 mg weight loss per cycle) or less
dense pattern of #8 blisters, but shall have no when tested in accordance with Paragraph
more than the “few” pattern of #6 blisters as 3.6 herein.
illustrated in the photographic reference ASTM
D714-02, “Standard Test Method for Evaluat- 5 Report
ing Degree of Blistering of Paints.” Testing
shall be in accordance with Paragraph 3.2. 5.1 The report shall cover the date the test was
Visual representations of the various degrees performed and the issue date of the report.
of blistering are shown in Figures 2 through 5 5.2 Identification of the specimen tested,
of this document. source of supply, manufacturer, model or se-
4.3 Accelerated weathering resistance ries number, or both, and any other pertinent
information.
When tested in accordance with Paragraph
3.3 herein, the paint film shall exhibit the fol- 5.3 A detailed description of the specimen
lowing traits: or specimens tested shall include the type of
prime or barrier coating if used, the method
4.3.1 No rust, checking, cracking, erosion or of coating application, the procedure used to
flaking shall be present. cure it and the dry film thickness.
4.3.2 No more than a few #6 blisters as il- 5.4 Any modifications made on the test speci-
lustrated in Figure 4 and in ASTM D714-02, men to obtain the values of acceptance shall
“Standard Test Method for Evaluating Degree be noted and described.
of Blistering of Paint.”
5.5 A statement that the test or tests were
4.3.3 A degree of chalking not to exceed #8 conducted in accordance with the methods
as illustrated in Figure 6 and in test method and procedures as specified herein. If devia-
B of ASTM D4214-98, “Standard Test Method tions from these methods and procedures were
for Evaluating Degree of Chalking of Exterior made, they shall be described in the report.
Paint Films.”
5.6 When the test is made to check the
4.3.4 No more than a 50% decrease in gloss conformance of the unit specimen to test re-
when tested in accordance with ASTM D523- quirements of a particular specification, the
89(1999), “Standard Test Method for Specular identification or description of the specification
Gloss.” shall be included in the report.
4.3.5 No more than a 10% change in color
(fade) when tested in accordance with ASTM
D2244-02e1, “Standard Practice for Calculation 6 General
of Color Tolerances and Color Differences from
Instrumentally Measured Color Coordinates.” 6.1 Testing laboratory
4.4 Impact test All tests shall be conducted and certified by
a nationally recognized, independent testing
No coating film removal shall occur other than
laboratory.
at an area ⅛" (3.2 mm) in diameter at the center
of the impact area, when tested in accordance
6.2 Certification
with Paragraph 3.4.
When reference is made to this specification
4.5 Film adhesion
the following statement shall be used: “Finish
There shall be no adhesion loss less than a coating has been tested in conformance with
grade 3B as defined in ASTM D3359-02. This ANSI Standard A250.3-2006.”
3
(5:0:+0(
;HISL¶9\Z[NYHKLZ
9\Z[ .YHKL 4H_PT\T VM Y\Z[LK HYLH

-PN\YL¶=PZ\HSYLMLYLUJLMVYWLYJLU[HNLVMY\Z[

=PZ\HSL_HTWSLZPSS\Z[YH[PUNKLNYLLZVMISPZ[LYPUN
-,> 4,+0<4 4,+0<4 +,5:, +,5:,

-PN\YL¶)SPZ[LYZPaL

-,> 4,+0<4 4,+0<4 +,5:, +,5:,

-PN\YL¶)SPZ[LYZPaL

(5:0:+0(

=PZ\HSL_HTWSLZPSS\Z[YH[PUNKLNYLLZVMISPZ[LYPUN
(5:0:+0(
-,> 4,+0<4 4,+0<4 +,5:, +,5:,

-PN\YL¶)SPZ[LYZPaL

-,> 4,+0<4 4,+0<4 +,5:, +,5:,

-PN\YL¶)SPZ[LYZPaL

(5:0:+0(
-PN\YL¶7OV[VNYHWOPJYLMLYLUJLZ[HUKHYKMVYKLNYLLVMJOHSRPUN

(5:0:+0(
;HISL¶*SHZZPÄJH[PVUVMHKOLZP]L[LZ[YLZ\S[Z
:\YMHJL VM JYVZZJ\[ HYLHZ MYVT

*SHZZPMPJH[PVU ÔPJO SPZ[PUN OHZ VJJ\YYLK ,_ 9H[L VM HKOLZPVU
HTWSL MVY ZP_ WHYHSSLS J\[Z
;OL LKNLZ VM [OL J\[Z HYL

JVTWSL[LS` ZTVV[O" UVUL VM
) 5VUL
[OL ZX\HYLZ VY [OL SH[[PJL HYL
KL[HJOLK
:THSS MSHRLZ VM JVH[PUN HYL

KL[HJOLK H[ PU[LYZLJ[PVUZ"
)
SLZZ [OHU VM [OL HYLH PZ
HMMLJ[LK
:THSS MSHRLZ VM JVH[PUN HYL

KL[HJOLK HSVUN LKNLZ HUK
) H[ PU[LYZLJ[PVUZ VM J\[Z ;OL
HYLH HMMLJ[LK PZ [V VM
[OL SH[[PJL
;OL JVH[PUN OHZ MSHRLK HSVUN

[OL LKNLZ HUK H[ WHY[Z VM [OL
)
ZX\HYLZ ;OL HMMLJ[LK HYLH PZ
[V VM [OL SH[[PJL
;OL JVH[PUN OHZ MSHRLK HSVUN

[OL LKNLZ VM J\[Z PU SHYNL YPI
) IVUZ HUK LU[PYL ZX\HYLZ OH]L
KL[HJOLK ;OL HYLH HMMLJ[LK
PZ [V VM [OL SH[[PJL
) -SHRPUN HUK KL[HJOTLU[ PU L_JLZZ VM

MEMBERS OF THE
Ceco Door
Milan, TN 38358
Curries
www.deansteel.com
Test Procedures
(909) 770-5700
HOLLOW METAL XPRESS
623-936-7000
www.meskerdoor.com
Corbin, KY 40701
155 Republic Drive
www.secmet.com
9017 Blue Ash Road
(513) 745-6400

440.899.0010 • FAX 440.892.1404
12/4/2014
www.steeldoor.org
Revision of ANSI/SDI A250.4-2001
Test Procedure and Acceptance Criteria for –

Physical Endurance for
:765:69
:[LLS+VVY0UZ[P[\[L
(WWYV]LK1\UL
(5:0:+0
(
9L]PZPVUVM(5:0:+0(
Physical Endurance for
:LJYL[HYPH[
(WWYV]LK1\UL
(TLYPJHU5H[PVUHS:[HUKHYKZ0UZ[P[\[L0UJ
(TLYPJHU (WWYV]HS VM HU (TLYPJHU 5H[PVUHS :[HUKHYK YLX\PYLZ ]LYPMPJH[PVU I` (5:S
[OH[ [OL YLX\PYLTLU[Z MVY K\L WYVJLZZ JVUZLUZ\Z HUK V[OLY JYP[LYPH MVY
5H[PVUHS HWWYV]HS OH]L ILLU TL[ I` [OL Z[HUKHYKZ KL]LSVWLY
:[HUKHYK *VUZLUZ\Z PZ LZ[HISPZOLK ÔLU PU [OL Q\KNLTLU[ VM [OL (5:S )VHYK VM
:[HUKHYKZ 9L]PL^ Z\IZ[HU[PHS HNYLLTLU[ OHZ ILLU YLHJOLK I` KPYLJ[S`
HUKTH[LYPHSS`HMMLJ[LKPU[LYLZ[Z:\IZ[HU[PHSHNYLLTLU[TLHUZT\JOTVYL
[OHUHZPTWSLTHQVYP[Ì\[UV[ULJLZZHYPS`\UHUPTP[`*VUZLUZ\ZYLX\PYLZ
[OH[ HSS ]PL^Z HUK VIQLJ[PVUZ IL JVUZPKLYLK HUK [OH[ H JVUJLY[LK LMMVY[
IL THKL [V^HYK [OLPY YLZVS\[PVU
;OL\ZLVM(TLYPJHU5H[PVUHS:[HUKHYKZPZJVTWSL[LS`]VS\U[HY`"[OLPYL_PZ
[LUJLKVLZUV[PUHU`YLZWLJ[WYLJS\KLHU`VULÔL[OLY[OLÒH]LHWWYV]LK
[OLZ[HUKHYKZVYUV[MYVTTHU\MHJ[\YPUNTHYRL[PUNW\YJOHZPUNVY\ZPUN
WYVK\J[Z WYVJLZZLZ VY WYVJLK\YLZ UV[ JVUMVYTPUN [V [OL Z[HUKHYKZ
;OL(TLYPJHU5H[PVUHS:[HUKHYKZ0UZ[P[\[LKVLZUV[KL]LSVWZ[HUKHYKZHUK
^PSS PU UV JPYJ\TZ[HUJLZ NP]L HU` PU[LYWYL[H[PVU VM HU` (TLYPJHU 5H[PVUHS
:[HUKHYK 4VYLV]LY UV WLYZVU ZOHSS OH]L [OL YPNO[ VY H\[OVYP[` [V PZZ\L
HU PU[LYWYL[H[PVU VM HU (TLYPJHU 5H[PVUHS :[HUKHYK PU [OL UHTL VM [OL
(TLYPJHU5H[PVUHS:[HUKHYKZ0UZ[P[\[L9LX\LZ[ZMVYPU[LYWYL[H[PVUZZOV\SK
IL HKKYLZZLK [V [OL ZLJYL[HYPH[ VY ZWVUZVY ÔVZL UHTL HWWLHYZ VU [OL
[P[SL WHNL VM [OPZ Z[HUKHYK
*(<;065 56;0*,! ;OPZ (TLYPJHU 5H[PVUHS :[HUKHYK TH` IL YL]PZLK VY
^P[OKYHÛ H[ HU` [PTL ;OL WYVJLK\YLZ VM [OL (TLYPJHU 5H[PVUHS :[HU
KHYKZ0UZ[P[\[LYLX\PYL[OH[HJ[PVUIL[HRLUWLYPVKPJHSS`[VYLHMMPYTYL]PZL
VY ^P[OKYH^ [OPZ Z[HUKHYK 7\YJOHZLYZ VM (TLYPJHU 5H[PVUHS :[HUKHYKZ
TH` YLJLP]L J\YYLU[ PUMVYTH[PVU VU HSS Z[HUKHYKZ I` JHSSPUN VY ^YP[PUN [OL
(TLYPJHU 5H[PVUHS :[HUKHYKZ 0UZ[P[\[L
7\ISPZOLKI`
:[LLS +VVY 0UZ[P[\[L

+L[YVP[ 9VHK *SL]LSHUK 6OPV
*VW`YPNO[I`:[LLS+VVY0UZ[P[\[L
(SSYPNO[ZYLZLY]LK
5VWHY[VM[OPZW\ISPJH[PVUTHÌLYLWYVK\JLKPUHU`
MVYTPUHULSLJ[YVUPJYL[YPL]HSZ`Z[LTVYV[OLY^PZL
^P[OV\[WYPVY^YP[[LUWLYTPZZPVUVM[OLW\ISPZOLY
7YPU[LKPU[OL<UP[LK:[H[LZVM(TLYPJH
(5:0:+0(
*VU[LU[Z
7HNL
-VYL^VYK PP
7\YWVZL
9LMLYLUJL KVJ\TLU[Z
(WWHYH[\Z HUK LX\PWTLU[
+VVY VWLULY
/HYK^HYL
7YLWHYH[PVU MVY [LZ[
;LZ[ ZWLJPTLU
+VVYZ
-YHTLZ
:^PUN [LZ[
+VVYZ
-YHTL
;^PZ[ [LZ[
(JJLW[HUJL JYP[LYPH
+VVYZ
-YHTLZ
-PN\YLZ
:^PUN ;LZ[ +L[HPS
( :^PUN ;LZ[ +L[HPS
;^PZ[ ;LZ[
7LYMVYTHUJL 9LWVY[Z
:^PUN ;LZ[ -VYT
:^PUN ;LZ[ -VYT
;^PZ[ ;LZ[ -VYT
P
-VYL^VYK;OPZ-VYL^VYKPZUV[WHY[VM(TLYPJHU5H[PVUHS:[HUKHYK(
;OL TH[LYPHS JVU[HPULK PU [OPZ KVJ\TLU[ OHZ ILLU KL]LSVWLK \UKLY [OL
H\ZWPJLZ VM [OL ;LJOUPJHS *VTTP[[LL VM [OL :[LLS +VVY 0UZ[P[\[L
;OLVYPNPUHSZ[HUKHYK^HZPZZ\LKVU1\S` HUK^HZYL]PZLKPU
HUK ;OL J\YYLU[ LKP[PVU PZ H YL]PZPVU VM [OL KVJ\TLU[
^P[O[OLJVU[LU[ZILPUN\WKH[LK[VYLMSLJ[JOHUNLZ[OH[OH]L[HRLUWSHJL
PU [OL Z[LLS KVVY HUK MYHTL PUK\Z[Y` ZPUJL [OH[ [PTL
:\NNLZ[PVUZ MVY PTWYV]LTLU[ NHPULK PU [OL \ZL VM [OPZ Z[HUKHYK HYL ^LS
JVTLHUKZOV\SKILZLU[[V[OL:[LLS+VVY0UZ[P[\[L+L[YVP[9VHK
*SL]LSHUK 6OPV
;OLVYNHUPaH[PVUZÔPJOHWWYV]LK[OPZZ[HUKHYKHUKHYLWHY[VM[OL(JJYLK
P[LK:[HUKHYKZ*VTTP[[LL(MVYTLK-LIY\HY` HYLHZMVSSV^Z!
(TLYPJHU 0UZ[P[\[L VM (YJOP[LJ[Z
)\PSKLYZ /HYK^HYL 4HU\MHJ[\YLYZ (ZZVJPH[PVU
*HUHKPHU :[LLS +VVY 4HU\MHJ[\YLYZ (ZZVJPH[PVU
*LKHY =HSSL` (ZZVJPH[LZ
+VVY HUK /HYK^HYL 0UZ[P[\[L
-4 (WWYV]HSZ
/44(+P]PZPVU VM 5((44
0U[LY[LR ;LZ[PUN :LY]PJLZ
:[LLS +VVY 0UZ[P[\[L
;OLYTH;Y\
<UKLY^YP[LYZ 3HIVYH[VYPLZ 0UJ
;OL;LJOUPJHS*VTTP[[LLVM[OL:[LLS+VVY0UZ[P[\[LÔPJOKL]LSVWLK[OPZ
Z[HUKHYK OHK [OL MVSSV^PUN WLYZVUULS H[ [OL [PTL VM HWWYV]HS!
;LYY` :PTWZVU *OHPYTHU

*SH\Z /LPKL =PJL *OHPYTHU
1 1LMMLY` >OLYY` 4HUHNPUN +PYLJ[VY
6YNHUPaH[PVU9LWYLZLU[LK 5HTLVM9LWYLZLU[H[P]L
(T^LSK)\PSKPUN7YVK\J[Z0UJ 4PRL2VSV]PJO
*LJV+VVY7YVK\J[Z ;VT1HUPJHR
*\YYPLZ*VTWHU` +H]L+LKPJ
+LHUZ[LLS4HU\MHJ[\YPUN*VTWHU` *SH\Z/LPKL
+VVY*VTWVULU[Z ;VT7VWV^
4LZRLY+VVY*VTWHU` 4PRL;VYYLZ
4L[HS7YVK\J[Z0UJ ;VT:[VUL
7PVULLY0UK\Z[YPLZ 2HTHS:OLPRO
9LW\ISPJ 1HZVU3PZL^ZRP
:LJ\YP[`4L[HS7YVK\J[Z*VYWVYH[PVU ;LYY`:PTWZVU
:[LLSJYHM[ 2\Y[9VLWLY
PP
AMERICAN NATIONAL STANDARD ANSI/SDI A250.4-2011

Physical Endurance for Steel Doors, Frames
and Frame Anchors
1 Purpose testing door or frame shall be anchored in such a

manner as to ensure rigidity.
The primary purpose of this procedure shall be to
establish a standard method of testing the perfor- The swinging mechanism shall be in two parts:
mance of a steel door mounted in a hollow metal 2.1 Door opener
or channel iron frame installed with appropriate an-
chors, under conditions that might reasonably be The door opener shall be an air motor positioned
considered an accelerated field operating condi- at 65° to the plane of the door in its closed posi-
tion. tion that will actuate an exit device mounted on the
test door. The contact point shall be set to push the
The user of this performance standard must temper door open 60° ± 5°, and retract to allow the door
his usage with the knowledge that there are many closer to bring the door back into its original closed
variables that affect door and frame performance, position and then begin the cycle again. See the
such as different hardware, anchors, glass and lou- specifications in figures 1 and 1A.
ver cutouts, field modification by parties other than
2.2 Hardware
the manufacturer, environmental factors, such as
heat, cold, moisture, etc. The exit device, door closer and hinges used in
testing shall be selected based on the manufac-
1.1 Reference documents
turer’s recommendations for the testing level de-
ANSI/BHMA A156.1-2006 Butts and Hinges scribed in Swing Test Form 1. The manufacturer
and model number shall be recorded in the report.
ANSI/BHMA A156.3-2008 Exit Devices All hardware shall be applied to the door and frame
ANSI/BHMA A156.4-2008 Door Controls – Clos- with fasteners provided by the hardware manufac-
ers turer (for example, machine screws or sex bolts) in
the location recommended by the door manufac-
ANSI/BHMA A156.7-2009 Template Hinge Di- turer. The hardware shall conform to the latest edi-
mensions tions of American National Standards ANSI/BHMA
A156.1, 3, 4 and 7. The device shall be set to close
2 Apparatus and equipment the door at a rate of 15 cycles, ± 1, per minute.
The apparatus and equipment used shall be the Inspect all hardware and silencers at regular in-
same when testing doors or frames with frame tervals, and adjust or replace as necessary. It is
anchors. The main testing structure shall be con- acceptable to apply lubrication to hinges and exit
structed as shown in figures 1 and 2. The structure devices.
shall conform to the parts shown, except the open-
Note: Where the applicable BHMA Test Standards
ing width and height are permitted to vary to allow have been followed, this information shall be record-
the testing of various door sizes. The test frame for ed in the test report.
1
3 Preparation for test the frame throat to simulate actual construction

conditions.
The door shall be hung in the frame on the hinges.
Care shall be taken to ensure the hinges are prop-
4 Test specimen
erly applied to the door and frame as recommend-
ed by the hinge manufacturer, and any hinge fillers 4.1 Doors
or shims, are in place. The clearance between the
Unless specified otherwise, the test shall be per-
door and the frame shall be recorded in the test
formed on a 3Ⱦ-0ɇ x 7Ⱦ-0ɇ nominal size door. A
report.
detailed description of the construction of the door
The door frame shall be securely fastened to the and the applicable processes such as welding,
test frame opening structure in accordance with bonding, etc., used for attaching components, shall
the manufacturer’s instructions. The manufacturer be recorded in the test report, Swing Test Form 1,
is permitted to select anchors for specific wall ap- under the “remarks” section.
plications (i.e., wood stud anchors or steel stud an-
4.2 Frames
chors, loose or welded in or existing masonry wall
anchors). Unless specified otherwise, the test shall be per-
formed on a 3Ⱦ-0ɇx 7Ⱦ-0ɇ nominal size frame hav-
Silencers shall be installed on the frame and the
ing a 5 ¾ɇ jamb depth. A detailed description of the
stop face of the door shall contact the silencers.
door frame which shall cover all components used
The frame shall be plumb, square, and rigid.
in the frame’s construction, as well as applicable
When applicable, wall surface materials (e.g., dry- processes (such as welding, etc.) used for attach-
wall) shall be applied to the test frame opening at ing and connecting components, shall be recorded
1q dia. x 5q long
roller contact pad
Air motor
Air motor stand
Set screw
Contact panic bar at attach to
center third of door piston rod
Detail “A”
Air lube unit
Panic bar
Mechanical counter
or equivalent
65°
Standard hollow metal frame

Detail “A”
mounted in channel iron frame
Full mortise butts

60°
Door closer
Door 3070
Figure 1 – Swing test detail
2
in the test report, Swing Test Form 2, under the nents readily accessible, such as face skins, ex-
“remarks” section. posed hinge and lock stiles, flush closing channels,
end closures, hinge reinforcements, and lock body/
A detailed description of the frame and anchoring
face plate reinforcements and shall cover the integ-
system which shall cover all details of the anchors,
rity of assembly methods used to connect the door
as well as the means of attachment in the frame
components.
and the weight of the door used for the test shall
be recorded in the test report, Swing Test Form 2. Doors which have passed the cycling criteria at
one level shall be deemed to have passed all lower
5 Swing test levels. The results shall be recorded on a standard
performance report, Swing Test Form 1.
5.1 Doors
5.2 Frame
Duration of the test shall be 250,000 cycles with
latching for Level C doors; 500,000 cycles Duration of the test shall be 250,000 cycles for
with latching for Level B doors; and 1,000,000 Level C frames; 500,000 cycles for Level B frames;
cycles with latching for Level A doors. A general and 1,000,000 cycles for Level A frames. A general
inspection of the door shall be made at 25,000 inspection of the frame shall be made at 25,000
cycle intervals for the first 100,000 cycles and at cycle intervals for the first 100,000 cycles and at
50,000 cycles thereafter. A mechanical counter or 50,000 cycle intervals thereafter.
equivalent shall be used to record the cycles.
The general inspection shall cover perimeter clear-
The general inspection shall cover perimeter clearances between door and frame and all frame
ances between door and frame and all compo- components readily accessible, such as corner
1q dia. x 5q long
roller contact pad
Air motor
Air motor stand
Set screw
Contact panic bar at attach to
center third of door piston rod
Detail “A”
Air lube unit
Panic bar
Mechanical counter
or equivalent
5q adjustable C.I. frame 65°
location varies to
accomodate different 5q Stationary C.I. frame
Detail “A”
size doors
Half mortise butts

60°
Door closer
Door 3070
Figure 1A – Swing test detail

Door can be tested in channel iron frame with half mortise hinges (no pressed steel frame).
3
21 4" max
Scre ack
21 4" max
orce gage
emove hinge pins

est frame
Pressure pad
Long range et een force gage
dial indicator Lever operated and door, 21 2" dia.
toggle clamps
at ad acent corners
Figure 2 – Twist test
clips and screws, corner tabs and slots, head and area illustrated in figure 2. The deflection noted on
jamb tabs/slots hinge reinforcements, and strike the dial indicator shall be plotted against the load
reinforcements and shall cover the integrity of as- applied to the corner on Twist Test Form 3. A maxi-
sembly methods used to connect the frame com- mum 300 lb. load shall be applied. The load shall
ponents then be reduced in 30 lb. increments and corre-
Door frames which have passed the cycling criteria sponding deflections recorded and plotted on Twist
at one level shall be deemed to have passed all Test Form 3. A smooth curve drawn through the
lower levels. The results shall be recorded as part points shall graphically demonstrate the reaction of
of the test report, Swing Test Form 2. the door to increasing and decreasing pressures at
different cycle intervals.
6 Twist test At the completion of each twist test, the hinges
The twist test is applicable in evaluating door con- shall be reassembled by means of inserting the
struction only. hinge pins, silencers shall be reinstalled, the exit
devise shall be latched, and the assembly shall be
The deterioration of the door strength during the
subjected to another 25,000 or 50,000 cycles. The
cycle test, if any, shall be checked through a series
condition of the silencers shall be noted and re-
of twist tests. These twist tests shall be performed
placements made where deemed necessary.
before the cycle test begins and then at 25,000
cycle intervals for the first 100,000 cycles and at
50,000 cycle intervals for the balance of the test. 7 Acceptance criteria
During the twist test, the hinge pins and silenc- 7.1 Doors
ers shall be removed from the door and frame as- 7.1.1 Doors shall not show any visual indication of
sembly and the exit device shall be unlatched. The metal fatigue, cracking or deformation at hardware
door is then clamped in place as noted in figure cutouts or along form contours.
2. If necessary to facilitate twist testing, the door
is permitted to be taken from the test fixture and 7.1.2 Doors of laminated construction (cores lami-
installed in a separate twist fixture. Loads in 30 lb. nated to face sheets, channels or stiffeners lami-
increments shall be applied at the upper lock edge nated to face sheets, etc.) shall not delaminate in
corner through the screw jack and force gage in the excess of 10% of the total surface area.
4
7.1.3 In doors of welded construction (stiffeners horizontal and a vertical cut at the center of the
or channels welded to face sheets, etc.) breakage door height and door width. Internal construction
of welds shall not exceed 10% of the total weld of of door shall be inspected visually for delamina-
those face stiffeners. tion, metal fatigue, cracking and weld failure. The
results of this inspection shall be recorded in the
7.1.4 Top, bottom or edge channels shall remain
test report.
securely in place, without any weld breakage.
7.2 Frames
7.1.5 Where seams occur on doors, there shall be
no opening or spreading of the seam. 7.2.1 Frames shall remain plumb, square, rigid,
and show no visual signs of metal fatigue, crack-
7.1.6 All hardware reinforcements shall remain se- ing, or deformation at hardware cutouts or along
curely in place and show no visual signs of metal form contours.
fatigue, cracking or deformation.
7.2.2 Corners shall stay aligned with seams in a
7.1.7 As a result of the twist test, the maximum closed position.
deflection permitted shall not exceed 2 ½ɇ when
loaded to 300 lb. for Level C. For Level B and Level 7.2.3 Perimeter clearances between door and
A doors the maximum deflection shall not exceed frame shall not be greater than 1⁄16ɇ from those
1 ¼ɇ when loaded to 300 lb. listed at onset of test.
7.1.8 Permanent deflection for doors shall not ex- 7.2.4 Hardware reinforcements shall remain se-
ceed ⅛ɇ when load is removed. curely attached to the frame, with all welds intact.
7.1.9 Tapped holes shall not strip. 7.2.5 Tapped holes shall not strip.
7.2.6 At the completion of the test, the frame shall
7.1.10 At the completion of the swing and twist
not limit door operation. If during the test the door
tests, the door shall be fully operable.
becomes inoperable, it shall be determined wheth-
7.1.11 Upon completion of the foregoing checks er a defective door frame, hardware reinforcement,
and measurements, remove door from test struc- hinge, frame anchor, etc., caused the failure and
ture and cut door into four equal sections with a shall be so noted in the test report.
5
Performance Report — Swing Test Form 1 'DWH

7HVW
0DQXIDFWXUHUV Type and Size of Doors

:HLJKW RI 'RRU
Inspection at 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
indicated cycle 25 50 75 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000
M M M M M M M M M M M M M M M M M M M M M M
intervals (1)
Condition of edge
weld/bond
Condition of lock
prep.
Condition of hinge
prep.
Top
Center
Bottom
Condition of top
closure
Condition of bottom
closure
Condition of door
core/stiffeners
Condition of panels
— general
Level C Door c Level B Door c Level A Door c
(1)
,QGLFDWHV FRQGLWLRQ LQ DSSURSULDWH FROXPQV
6 ³ 6DWLVIDFWRU\
8VH IRRWQRWHV XQGHU 5HPDUNV IRU IXUWKHU H[SODQDWLRQ
+LQJH 0DQXIDFWXUHU 1XPEHU

/RFN 0DQXIDFWXUHU 1XPEHU
&ORVHU 0DQXIDFWXUHU 1XPEHU
Remarks:
6
Performance Report — Swing Test Form 2 'DWH
0DQXIDFWXUHUV 7HVW
-DPE :LGWK Type and Size of Frame

:HLJKW RI 'RRU Type of Anchors
Inspection at 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
indicated cycle 25 50 75 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000
M M M M M M M M M M M M M M M M M M M M M M
intervals (1)
Condition of general
appearance
Condition of
perimeter clearance
Condition of strike
prep.
Condition of hinge
prep.
Top
Center
Bottom
Condition of
silencers
Condition of wall
anchors
Condition of floor
anchors
Condition of miters
Level C Door c Level B Door c Level A Door c

,QGLFDWHV FRQGLWLRQ LQ DSSURSULDWH FROXPQV
(1)
6 ³ 6DWLVIDFWRU\
8VH IRRWQRWHV XQGHU 5HPDUNV IRU IXUWKHU H[SODQDWLRQ
+LQJH 0DQXIDFWXUHU 1XPEHU

/RFN 0DQXIDFWXUHU 1XPEHU
Remarks:
7
8
Performance Report — Twist Test Form 3
7HVW 1R 'DWH
3URGXFW 'HVFULSWLRQ
480
450
420
390
360
330
300
270
240
210
180
150
3RXQGV /RDG$SSOLHG
120
90
60
30
0
0.1 0.5 1.0 1.5 2.0 2.5 3.0
,QFKHV 'HIOHFWLRQ
MEMBERS OF THE
Ceco Door
Milan, TN 38358
Curries
www.deansteel.com
Test Procedures
(909) 770-5700
HOLLOW METAL XPRESS
623-936-7000
www.meskerdoor.com
Corbin, KY 40701
155 Republic Drive
www.secmet.com
9017 Blue Ash Road
(513) 745-6400

440.899.0010 • FAX 440.892.1404
12/4/2014
www.steeldoor.org
ANSI/SDI A250.6-2003 (R2009)
Recommended Practice for

Hardware Reinforcing
on Standard Steel Doors and Frames
:765:69
:[LLS+VVY0UZ[P[\[L
(WWYV]LK6J[VILY
ANSI/SDI ®
A250.6-2003 (R2009)
Recommended Practice
for Hardware Reinforcing
Secretariat
Approved October 7, 2003


Published by



ANSI/SDI A250.6–2003
Contents
Page
1 General .........................................................................................1
1.1 Purpose ......................................................................................1
1.2 Scope .........................................................................................1
1.3 Reinforcing methods ...................................................................1
2 Metrication ....................................................................................1
3 Reference documents ...................................................................2
4 Recommended reinforcing thickness .............................................2
5 Recommended application of hardware .........................................2
5.1 Mortised hardware ......................................................................2
5.2 Field drilling and tapping .............................................................3
5.3 Thru-bolting ................................................................................4
5.4 Sheet metal screws .....................................................................4
6 Continuous hinges ........................................................................6
Tables
1 Minimum hardware reinforcing thickness .......................................3
2 #10/24 thread (nm) ........................................................................4
3 #12-24 thread (nm)........................................................................4
4 Tap drills and clearance drills for machine screws
with American National Thread form (nm) ......................................5
Figures
1 Rigidity of angle or channel versus plate ......................................1
2 Full #12-24 (nm) threads ...............................................................2
3 Extrusion to create (3) full threads of #12-24 (nm) ........................2
4 Maintain a minimum of 65% of full thread .....................................4
5 Full thread shall not fall below 65% ..............................................4
6 Sex-bolted ....................................................................................6
7 Improper thru-bolting ....................................................................6
Appendices
A Conclusion ....................................................................................7
B Bibliography ..................................................................................8
i
The first edition of this standard was developed under the auspices of the
Technical Committee of the Steel Door Institute and published in 1978 as
SDI-107 Hardware on Steel Doors (Reinforcement – Application). In 1994,
the word “standard” was added to the document’s title and the decision
was made to promulgate SDI-107 as an American National Standard.
A250.6 was officially approved by the American National Standards Insti-
tute on October 22, 1997. Substantive changes between SDI-107 and the
revised and redesignated A250.6-1997 Hardware on Standard Steel Doors
(Reinforcement – Application) include the addition of metric equivalents,
revised tap and drill sizes to eliminate those that are not recommended,
and a better definition for “factory mortise.”
In 2001, the TC-1 Committee of the Accredited Standards Committee
A250 initiated the 5-year review process, and changed the title of A250.6
to Recommended Practice for Hardware Reinforcing on Standard Steel
Doors and Frames to more accurately define the content of the standard.
In addition, this revision includes the following substantive changes: Ad-
dition of Appendices A and B, both informative; discontinuation of the use
of “gauge” in favor of decimal equivalents; addition of information relating
to continuous hinges; redefinition of the scope to exclude “architecturally
specified or specialized conditions.”
welcome, and should be sent to the Steel Door Institute, 30200 Detroit
The organizations of the Accredited Standards Committee A250 that have
approved this standard are as follows:
American Iron and Steel Institute
Canadian Steel Door Manufacturers’ Association
Factory Mutual Research Corporation
General Services Administration
Hollow Metal Manufacturers’ Association / Division of National Association
of Architectural Metal Manufacturers’ Association
Insulated Steel Door Institute
International Conference of Building Officials
Manufactured Housing Institute
National Association of Home Builders
Window and Door Manufacturers’ Association
ii
had the following personnel at the time of approval:
Robert Berhinig, Chairman

American Institute of Architects ................................................. Christopher Bushnell
American Iron & Steel Institute ................................................... Robert Wills
Amweld Building Products, LLC ................................................ Allan Ashachik
Benchmark Commercial Doors .................................................. Randall Barber
Builders Hardware Manufacturers Association .......................... Mike Tierney
Canadian Steel Door Manufacturers Association ...................... Bud Bulley
Ceco Door Products................................................................... Thomas R. Janicak
Curries Company ....................................................................... Stan Horsfall
Deansteel Manufacturing Company ........................................... Claus D. Heide
Door and Hardware Institute ...................................................... John Geniesse
Factory Mutual Research Corporation ....................................... Mark Tyrol
General Services Administration ................................................ Donald McGaha
Hollow Metal Manufacturers’ Association / Division of
National Association of Architectural Metal Manufacturers ....... Russell Tauscher
Ingersoll-Rand ............................................................................ Kurt Roeper
Intertek Testing Services ............................................................ Nancy Kokesh
The Kewanee Corporation.......................................................... Jason Lisewski
Magnatrax Corporation .............................................................. Craig Ordmandy
Manufactured Housing Institute ................................................. Mark Nunn
Mesker Door Company .............................................................. Stephen C. Frates
National Association of Home Builders ...................................... Jeff Inks
Pioneer Industries, Inc. .............................................................. Kamal Sheikh
Republic Builders Products ........................................................ Craig J. Ordmandy
Security Metal Products Corporation ......................................... Dan Buffenbarger
Underwriters Laboratories Inc. ................................................... Daniel Kaiser
Window & Door Manufacturers’ Association.............................. Rick Perry
iii
(4,90*(55(;065(3:;(5+(9+ (5:0:+0(
9LJVTTLUKLK7YHJ[PJLMVY/HYK^HYL9LPUMVYJPUN
VU:[HUKHYK:[LLS+VVYZHUK-YHTLZ
. LULYHS THU\MHJ[\YPUN WYVJLZZLZ ;OLZL WYVJLZZLZ

PUJS\KLMVYTPUNVW[PVUZZLLMPN\YLVYPU[LNYHS
7 \YWVZL N\ZZL[ZVYMPSSL[ZVUSPNO[LYNH\NLTLTILYZ[V
0[PZ[OLPU[LU[PVUVM[OPZW\ISPJH[PVU[VM\YUPZO HJOPL]L Z[YLUN[O HUK WLYMVYTHUJL LX\HS [V
\ZLYZHUKWYVZWLJ[P]L\ZLYZVMZ[HUKHYKZ[LLS OLH]PLY NH\NL TLTILYZ
KVVYZ HUK MYHTLZ ^P[O WYHJ[PJHS PUMVYTH[PVU >OLYL YLPUMVYJLTLU[Z YLX\PYL [HWWPUN
YLNHYKPUN HJJLW[LK KLZPNU TL[OVKZ MVY YLPU MVYTHJOPULZJYL^[OYLHKZHULX\P]HSLU[U\T
MVYJPUNHUKYLJVTTLUKLKWYHJ[PJLZMVYWYVWLY ILY VM [OYLHKZ TH` IL YLUKLYLK PU H SPNO[LY
MPLSK WYLWHYH[PVU MVY I\PSKLYZ» OHYK^HYL NH\NL WHY[ ^P[O H WPLYJLK HUK KPTWSLK ¸L_
: JVWL [Y\KLK¹OVSLHZJVTWHYLK[VHOLH]PLYNH\NL
WHY[THU\MHJ[\YLK^P[OJVU]LU[PVUHSWYVJLZZ
;OL PUMVYTH[PVU JVU[HPULK OLYLPU WLY[HPUZ [V LZ -VY L_HTWSL LX\HS [OYLHK KLW[O JHU IL
KVVYZHUKMYHTLZTHU\MHJ[\YLKPUHJJVYKHUJL HJOPL]LKVUHWPLJLVM TTTL[HS
^P[O(5:0:+0(:+0¸9LJVTTLUKLK HUK VU H MSH[ WSH[L VM TT TL[HS
:WLJPMPJH[PVUZ MVY : [HUKHYK :[LLS +VVYZ HUK ZLL MPN\YLZ HUK ;OL L_[Y\ZPVU WYVJLZZ
-YHTLZ¹W\ISPZOLKI`[OL:[LLS+VVY0UZ[P[\[L YLZ\S[ZPULX\HSZ[YLUN[OLX\P]HSLU[U\TILYVM
0[ PZ UV[ PU[LUKLK [V YLMLYLUJL HYJOP[LJ[\YHSS` [OYLHKZ HUK H SPNO[LY ^LPNO[ [OHU [OL WHYLU[
ZWLJPMPLK VY ZWLJPHSPaLK ZP[\H[PVUZ IL`VUK TL[HS VY LX\P]HSLU[ MSH[ YLPUMVYJPUN WSH[L
[OL ZJVWL VM [OPZ KVJ\TLU[ VY KVJ\TLU[Z
OLYLPU 4 L[YPJH[PVU
9 LPUMVYJPUN TL[OVKZ 4L[YPJ :0 <UP[Z HYL PUKPJH[LK PU WHYLU[OLZPZ
;OPZ Z[HUKHYK YLJVNUPaLZ HZ LX\HS H ]HYPL[` MVSSV^PUN JVU]LU[PVUHS SPULHY TLHZ\YLTLU[Z
VM YLPUMVYJPUN TL[OVKZ WYVK\JLK I` \UPX\L ;OLZL HYL ¸ZVM[ JVU]LYZPVU¹ HWWYV_PTH[LZ
0.123 0.093
[3.1 mm] [2.3 mm]
Plate
0.067
[1.7 mm] Angle
Channel
-PN\YL¶9PNPKP[`VMHUNSLVYJOHUULS]LYZ\ZWSH[L

(5:0:+0(
(3) ull hreads 0.123

3.1 mm
-PN\YL¶-\SS
UT[OYLHKZ
H e t e ie ed nd
di ed e t uded t u
ent stee e e t in .
.
.
-PN\YL¶,_[Y\ZPVU[VJYLH[LM\SS[OYLHKZVM
UT
IHZLK VU /44( ¸:[LLS ;HISLZ¹ <UP[Z V[OLY^PZL YLPUMVYJPUN HUK [HWWLK TV\U[PUN
^P[OV\[ TL[YPJ LX\P]HSLU[Z HYL PUKPJH[LK HZ OVSLZ MVY [LTWSH[L OPUNLZ HUK (5:0 KLMPULK
UT LN ZJYL^Z SVJRZ HZ ZWLJPMPLK (KKP[PVUHS YLPUMVYJPUN MVY
Z\YMHJLHWWSPLKOHYK^HYLZOHSSILI\PS[PU[V[OL
9 LMLYLUJL KVJ\TLU[Z KVVY H[ [OL MHJ[VY` ÔLU ZWLJPMPLK
(5:0:+0 (:+0 ¸9LJVTTLUKLK (Z H N\PKL [V ZWLJPMPJH[PVU ^YP[LYZ [HISL
:WLJPMPJH[PVUZ MVY :[HUKHYK :[LLS +VVYZ HUK ZOV^Z [OL TPUPT\T [OPJRULZZ VM Z[LLS [V IL
-YHTLZ¹ \ZLKMVYOHYK^HYLYLPUMVYJPUNHZLUKVYZLKI`
(5:0:+0 (
(5:0:+0(¸;LZ[7YVJLK\YLHUK(JJLW
[HUJL*YP[LYPHMVY7O`ZPJHS,UK\YHUJLMVY:[LLS
9
LJVTTLUKLK HWWSPJH[PVU VM OHYK
+VVYZ-YHTLZ-YHTL(UJOVYZHUK/HYK^HYL
^HYL
9LPUMVYJPUNZ¹
4 VY[PZLK OHYK^HYL
4HJOPULY`Z /HUKIVVR
:[HUKHYKPaLK HUK (5:0 KLMPULK WYLWHYH[PVUZ
9 LJVTTLUKLK YLPUMVYJPUN [OPJR HYLTHKLH[[OLMHJ[VY`[VHSSV^PUZ[HSSH[PVUVM
ULZZ TVY[PZL OHYK^HYL Z\JO HZ OPUNLZ HUK SVJRZ
/VSLZZOHSSILTHKL[VWYLJPZLKPHTL[LYZHUK
;OL 4HU\MHJ[\YLY IHZLK VU PUKP]PK\HS JVU
HJJ\YH[LS` [HWWLK [V PUZ\YL TH_PT\T [OYLHK
Z[Y\J[PVU TL[OVKZ HUK [VVSPUN JHWHIPSP[PLZ
LUNHNLTLU[ HUK OVSKPUN Z[YLUN[O *\[V\[Z
ZOHSS YLPUMVYJL [OLPY WYVK\J[ [V PUZ\YL WLYMVY
ZOHSS IL WPLYJLK [V Z\YYV\UK [OL TVY[PZLK
THUJL PU HJJVYKHUJL ^P[O (5:0:+0 (
OHYK^HYLP[LT[VJSVZL[VSLYHUJLZVU[OYLLVY
;OPZ YLPUMVYJPUN ZOHSS PUJS\KL \USLZZ UV[LK
HSSMV\YZPKLZ;OLOHYK^HYLZOHSSILPUZ[HSSLK

using only the proper screws as furnished tion, some hardware such as anchor hinges,
with or specifically recommended for each thrust pivots, pivot reinforced hinges or floor
device. mounted pivots must be field prepared due to
design variations or to provide adjustment that
NOTE: The installer must exercise caution
upon initial insertion of screws to prevent cross can only be provided at time of installation.
threading, especially with the smaller diameter The installer shall use a template provided
screws. with the device or the device itself to locate
5.2 Field drilling and tapping hole spacing.
Doors and frames shall be prepared by the 5.2.1 A suitably sized punch shall be used
installer in the field for surface applied hard- to locate the drilling for pilot holes to prevent
ware, such as surface closers or holders, track drill creeping, off-center holes and improper
type concealed closers or holders, pulls, exit screw alignment.
device cases, or vertical rod latches. In addi-
Table 1 – Minimum hardware reinforcing thickness
Door Frame
Hardware Item
inches mm MSG No. (6) inches mm MSG No. (6)
Mortise Hinge 1-3/8" [34.9 mm] Door (1) 0.093 2.3 12 0.093 2.3 12
Mortise Hinge 1-3/4" [44.5 mm] Door (1) (2)
0.123 3.1 10 0.123 3.1 10
Mortise Lock or Deadbolt (1)
0.067 1.7 14 0.067 1.7 14
Bored Lock or Deadbolt (1)
0.067 1.7 14 0.067 1.7 14
Flush Bolt Front (1) 0.067 1.7 14 0.067 1.7 14
Surface Bolt (3) 0.067 1.7 14 0.067 1.7 14
Surface Applied Closer (4) 0.067 1.7 14 0.067 1.7 14
Hold Open Arm (3)
0.067 1.7 14 0.067 1.7 14
Pull Plates and Bar (3)
0.053 1.3 16 0.053 1.3 16
Surface Exit Device (3)
0.067 1.7 14 0.067 1.7 14
Floor Checking Hinge 0.167 4.2 7 0.167 4.2 7
Pivot Hinge 0.167 4.2 7 0.167 4.2 7
Continuous Hinges (5) Not Required Not Required
Kick / Push Plate Not Required Not Required
Note: The minimum steel thickness for each specific gage is derived from the published figures
of Underwriters Laboratories, Inc.
(1)
Thinner steel may be employed as long as tapped holes used for mounting the hardware are
extruded to produce an equivalent number of threads.
(2)
If reinforcing is angular or channel shaped, 0.093" (2.3 mm) is permitted.
(3)
When reinforcing is omitted, thru-bolting via the use of spacers or sex-bolts is required.
(4)
Reinforcement shall occur on both sides.
(5)
Refer to section 6.
(6)
MSG No. to be used for reference purposes only.
3
(5:0:+0(
Correct drill si e In e t d i si e
for pilot hole i t e
-PN\YL¶4HPU[HPUHTPUPT\TVMVMM\SS
[OYLHK -PN\YL¶-\SS[OYLHKZOHSSUV[MHSSILSV^
04769;(5;56;,!<ZLVUS`[OLJVYYLJ[ZPaL H[[HJOTLU[ ZOHSS IL HJJVTWSPZOLK I` [OY\

KYPSSMVYWPSV[OVSLZHZYLJVTTLUKLKI`¸4H IVS[PUN;OLOHYK^HYLTHU\MHJ[\YLY»ZPUZ[Y\J
JOPULY`»Z/HUKIVVR¹ZLL[HISL3HYNLYOVSLZ [PVU ZOLL[Z ZOHSS IL JSVZLS` MVSSV^LK MVY YLJ
^PSSKLJYLHZLZJYLÔVSKPUNWV^LYJH\ZPUN[OL VTTLUKLKWYVJLK\YLZ>OLYL[OY\IVS[PUNPZ
ZJYL^[VILW\SSLKMYVT[OLYLPUMVYJPUN\UKLY YLX\PYLK VU OVSSV^ TL[HS KVVYZ ZWHJLYZ VY
UVYTHS Z[YLZZLZ ZLL MPN\YLZ HUK ZL_IVS[Z ZOHSS IL \ZLK [V WYL]LU[ JVSSHWZPUN
VMMHJLZOLL[ZHZPSS\Z[YH[LKPUMPN\YLZHUK
;HISLZHUKPSS\Z[YH[L[OLLMMLJ[VM]HYPHUJLZ
PU WPSV[ OVSL ZPaLZ VU [OYLHK OVSKPUN WV^LY 56;,! ;OLTVZ[WVW\SHY[OY\IVS[PUNHWWSPJH
[PVUZ HYL KVVY JSVZLYZ L_P[ KL]PJLZ V]LYOLHK
;OL PUZ[HSSLY ZOHSS HZZ\YL [OH[ [HWWLK OVSKLYZ W\SSZ HUK IHY ZL[Z
OVSLZ OH]L VM M\SS [OYLHK JVUZPKLYLK H
:
OLL[ TL[HS ZJYL^Z
UVYTHS JVUKP[PVU ;OPZ WLYJLU[HNL ZOHSS UV[
MHSS ILSV^ [V IL JVUZPKLYLK HKLX\H[L :OLL[ TL[HS ZJYL^Z HYL UVYTHSS` \ZLK [V H[
MVY WYVWLY OHYK^HYL MHZ[LUPUNZ +YPSSZ ZOHSS [HJO HJJLZZVY` OHYK^HYL Z\JO HZ RPJRWSH[LZ
ILWVZP[PVULKZV[OLIP[LU[LYZ[OLYLPUMVYJLK THPSZSV[ZYVVTU\TILYZPKLU[PMPJH[PVUZPNUZ
HYLHPUWLYWLUKPJ\SHYWVZP[PVUHZOVSLZMVYTLK HUK PU THU` PUZ[HUJLZ W\ZO VY W\SS WSH[LZ
H[HUNSLZ^PSSUV[WLYTP[WYVWLYZLH[PUNVM[OL ;OLZL HYLHZ HYL UV[ YLPUMVYJLK IL`VUK [OL
ZJYL^ OLHK (M[LY [OL WYVWLY WPSV[ OVSLZ HYL [OPJRULZZ VM [OL MHJL ZOLL[Z 7YVWLYS` ZPaLK
KYPSSLK WYVJLLK ^P[O [OL [HWWPUN VWLYH[PVU OVSLZHUKJVYYLJ[ZOLL[TL[HSZJYL^ZHZWYV
;OL [HW ZOHSS TH[JO [OL [OYLHK ZPaL VM [OL ]PKLK ^P[O [OL OHYK^HYL P[LT VY HZ ZWLJPMPLK
ZJYL^Z WYV]PKLK HUK [OL [HW ZOHSS IL OLSK PU[OLTV\U[PUNPUZ[Y\J[PVUZZOHSSIL\ZLKMVY
WLYWLUKPJ\SHY [V [OL Z\YMHJL OHYK^HYL H[[HJOTLU[
; OY\IVS[PUN ;OL ILZ[ WLYMVYTHUJL PZ HJOPL]LK
ÔLU[OLZWHJLIL[^LLU[OL[OYLHKZPZLX\HS
>OLYL YLPUMVYJPUN OHZ UV[ ILLU ZWLJPMPLK VY
WYV]PKLK MVY V[OLY [OHU TVY[PZLK OHYK^HYL
;HISL¶
[OYLHKUT ;HISL¶
[OYLHKUT
+YPSS:PaL +YPSS+PHTL[LY -\SS;OYLHK +YPSS:PaL +YPSS+PHTL[LY -\SS;OYLHK

¸4HJOPULY`»Z/HUKIVVR¹YLJVTTLUKH[PVUPU)63+

¸4HJOPULY`»Z/HUKIVVR¹YLJVTTLUKH[PVUPU)63+

Table 4 – Tap drills and clearance drills for machine screws

with American National Thread form (nm)
Size of Screw Tap Drills Clearance Hole Drills

No. of
No. Threads Close Fit Free Fit
Decimal per Drill Decimal
or Drill Decimal Drill Decimal
Equiv. Inch Size Equiv.
Diam. Size Equiv. Size Equiv.
0 .060 80 3/64 .0469 52 .0635 50 .0700
64 53 .0595
1 .073 48 .0760 46 .0810
72 53 .0595
56 50 .0700
2 .086 43 .0890 41 .0960
64 50 .0700
48 47 .0785
3 .099 37 .1040 35 .1100
56 45 .0820
36* 44 .0860
4 .112 40 43 .0890 32 .1160 30 .1285
48 42 .0935
40 38 .1015
5 .125 30 .1285 29 .1360
44 37 .1040
32 36 .1065
6 .138 27 .1440 25 .1495
40 33 .1130
32 29 .1360
8 .164 18 .1695 16 .1770
36 29 .1360
24 25 .1495
10 .190 9 .1960 7 .2010
32 21 .1590
24 16 .1770
12 .216 2 .2210 1 .2280
28 14 .1820
20* 10 .1935
14 .242 D .2460 F .2570
24* 7 .2010
20 7 .2010
1/4 .250 F .2570 H .2660
28 3 .2130
18 F .2570
5/16 .3125 P .3230 Q .3320
24 I .2720
16 5/16 .3125
3/8 .375 W .3860 X .3970
24 Q .3320
14 U .3680
7/16 .4375 29/64 .4531 15/32 .4687
20 25/64 .3906
13 27/64 .4219
1/2 .500 33/64 .5156 17/32 .5312
20 29/64 .4531
* Screws marked with asterisk (*) are not in the American Standard but are from
the former ASME Standard.
5
(5:0:+0(
Sex nut et nut d es n t

full door thickness s n u d t i ness
-PN\YL¶:L_IVS[LK -PN\YL¶0TWYVWLY[OY\IVS[PUN
[V VY NYLH[LY [OHU [OL [OPJRULZZ VM [OL MHJL :[HUKHYK YLPUMVYJPUN ZOHSS IL H
ZOLL[Z TT Z[LLS Z[YPW UV SLZZ [OHU
TTPU^PK[OZLJ\YLS`^LSKLKPUZPKL[OLOPUNL
* VU[PU\V\Z OPUNLZ LKNLVMKVVYZHUKOPUNLQHTIKVVYYHIIL[VM
MYHTLZ
:[HUKHYKWYLWHYH[PVUMVYJVU[PU\V\ZNLHY
[`WLVYIHYYLS[`WLOPUNLZZOHSSUV[PUJS\KLHU` 6W[PVUHS YLPUMVYJPUN ZOHSS IL H
MHJ[VY` YLPUMVYJPUN KYPSSPUN HUKVY [HWWPUN PU TT Z[LLS Z[YPW UV SLZZ [OHU
KVVYZVYMYHTLZ(SSTV\U[PUNZOHSSILWYLWHYLK TTPU^PK[OZLJ\YLS`^LSKLKPUZPKL[OLOPUNL
PU [OL MPLSK I` [OL OHYK^HYL PUZ[HSSLY QHTI KVVY ZPKL MHJL VM MYHTLZ
-VY JVU[PU\V\Z OPUNLZ [OH[ YLX\PYL YLPU ;OLOHYK^HYLPUZ[HSSLYZOHSSJHYLM\SS`MVS
MVYJPUNLP[OLYMVYMHZ[LULYZKVVY^LPNO[KVVY SV^ [OL OPUNL THU\MHJ[\YLY»Z PUZ[Y\J[PVUZ MVY
ZPaLVYMYLX\LUJ`VM\ZLZP[\H[PVUZYLPUMVYJPUN MHZ[LULY WYLWHYH[PVUZ
ZOHSS IL PUKPJH[LK H[ [OL [PTL VM VYKLY

Appendix A
(informative)
Conclusion
It has been the experience of the Steel Door Institute that most failures of hardware attachments
have been caused by improper field installation rather than insufficient reinforcement. It is quite
obvious that it is easier to tap an oversize pilot hole than to tap one of correct size necessary
for maximum strength. Oversized holes will not ensure adequate product performance.
Manufacturing tolerances and dimensions may not always be consistent on machine and sheet
metal screws when compared with different sources of supply.
The material used for the manufacture of screws is also a factor in the overall performance of the
attachment. Stainless steel, for example, is a stronger fastener than aluminum or plain carbon
steel. On installations where vibration or unusual frequency of operation is a factor, the use of
thread locking inserts, liquids on threads, or binding heads should be considered.
Standard steel doors and top grade builders hardware are made to provide many years of service
and are very compatible. The specification writer and construction superintendent must be aware,
however, that proper installation methods must be considered on an equal basis with door and
hardware construction requirements to achieve this compatibility on the job.
7
Appendix B
(informative)
Bibliography
— HMMA 803 “Steel Tables”

— HMMA 830 "Hardware Selection for Hollow Metal Doors and Frames"
— HMMA 840 "Guide Specification for Installation and Storage of Hollow Metal Doors and
Frames"
— ANSI/SDI A250.7 “Nomenclature for Standard Steel Doors and Frames”
— SDI-117 “Manufacturing Tolerances for Standard Steel Doors and Frames”
— SDI-122 “Installation and Troubleshooting Guide for Standard Steel Doors and Frames”
8
Specifications for
Standard Steel Doors and Frames (SDI-100)
SPONSOR
Approved June 2, 2014
ANSI/SDI ®
A250.8-2014
Specifications for
(SDI-100)
Secretariat


Published by



Contents
Page
Foreword.. ............................................................................................ ii
1 G eneral..........................................................................................1
1.1 S cope..........................................................................................1
1.2 Reference Documents..................................................................1
1.3 A pproval Drawings and Hardware Schedules................................2
1.4 C lassification — Level, Performance, Model.................................2
1.5 S izes. . ..........................................................................................2
2 Products.........................................................................................3
2.1 G eneral.......................................................................................3
2.2 M anufacturers Standard Gage (MSG)
vs. Minimum Steel Thickness.......................................................5
2.3 Construction Features..................................................................5
2.4 Frames........................................................................................6
3 H ardware Preparation.....................................................................8
3.1 Reinforcings. . ...............................................................................8
4 S torage, Handling, and Installation.. ................................................9
4.1 J obsite Storage. . ..........................................................................9
4.2 Frame Installation........................................................................9
4.3 D oor Installation........................................................................ 10
4.4 H ardware Installation................................................................. 10
4.5 Installation of Factory Applied Finish Painted Materials.............. 10
4.6 D oor and Frame Maintenance.................................................... 10
4.7 D oor and Frame Repair............................................................. 10
Tables
1 Standard opening sizes.. .................................................................3
2 Steel thickness / door faces............................................................5
3 Minimum steel thickness / frames...................................................7
4 Minimum hardware reinforcing thickness.........................................8
5 Hardware locations.........................................................................9
Appendices
A Fire Door Considerations. . ............................................................ 11
B General Considerations................................................................ 13
C Section 08100 Standard Hollow Metal Doors and Frames............. 15
i
auspices of the ANSI A250 Committee. This committee has a diverse mem-
bership of users, producers, and general interest in addition to members
of the Steel Door Institute. The committee has been charged with the de-
velopment of standards, test methods, and other matters relating to steel
doors and frames.
The current edition is a revision, and replaces the ANSI A250.8-2003 docu-
ment. The contents have been updated to reflect changes that have taken
place in the steel door and frame industry since the time of the previous
publication. Some of the significant changes from the previous version are
as follows:
• Revised document title to remove the word “Recommended”
• Revised section 2.4.1.2 to clarify that existing wall or existing opening
design anchors are the only type of anchor that would work with an
existing wall
• Updated membership roster for ASC A250
• Updated membership roster for ASC A250 Technical Committee
• Revised title of ANSI/SDI A250.3 (1.2.2) to reflect current standard
• Removed reference to SDI-106 (1.2.1)
• Removed reference to A115 Hardware Preparations in Steel Doors and
Frames (1.2.2) in lieu of ANSI/BHMA A156.115
• Removed reference to ASTM A561-1998 (1.2.3) as standard was with-
drawn by ANSI
• Added reference to ASTM A879-06 (1.2.3)
welcome, and should be sent to the Steel Door Institute, 30200 Detroit
The organizations of the Accredited Standards Committee A250 that have
approved this standard are as follows:
American Institute of Architects/ARCOM
Architectural Testing
Canadian Steel Door Manufacturers Association
Cedar Valley Associates
Door Control Services
FM Approvals
HMMA/Division of NAAMM
National Wind Institute / Texas Tech
Underwriters Laboratories LLC
Vetrotech / Saint Gobain
Therma-Tru
ii
James Urban, Chairman

Allegion........................................................................................ Karen Bishop
American Institute of Architects................................................... Joseph Berchenko
Architectural Testing .................................................................... Dan Johnson
Builders Hardware Manufacturers Association............................ Mike Tierney
Canadian Steel Door Manufacturers Association........................ Bud Bulley
Ceco Door Products.................................................................... Tom Janicak
Cedar Valley Associates.............................................................. Stan Horsfall
Curries Company ........................................................................ Dave Dedic
Deansteel Manufacturing Company............................................ Claus Heide
Door and Hardware Institute........................................................ Greg Drake, AHC
Door Components Inc.................................................................. Tom Popow
Door Control Services................................................................. Craig Ordmandy
FM Approvals............................................................................... Mark Tyrol
HMMA/Division of NAAMM.......................................................... Russell Tauscher
Intertek Testing Services............................................................. Nancy Kokesh
Mesker Door, Inc.......................................................................... Mike Torres
Metal Products, Inc...................................................................... Tom Stone
National Wind Institute................................................................. Larry Tanner
Pioneer Industries, Inc................................................................. Kamal Sheikh
Republic....................................................................................... Steve Gilliam
Security Metal Products Corp...................................................... Terry Simpson
Steel Door Institute...................................................................... J. J. Wherry
Therma-Tru.................................................................................. Steve Jasperson
Underwriters Laboratories LLC.................................................... Luke Woods
Vetrotech Saint-Gobain................................................................ Christian Mueller
iii
Specifications
for Standard Steel Doors and Frames (SDI-100)
1 General – SDI-118-2012 Basic Fire Door, Fire Door

Frame, Transom/Sidelight Frame, and Window
1.1 Scope
Frame Requirements
This specification for standard swinging steel
– SDI-124-2011 Maintenance of Standard Steel
doors and frames offers a variety of choices
Doors and Frames
suitable for any commercial application. Spe-
cific performance levels of doors and frames 1.2.2 ANSI Standards
are defined herein. SDI-108, Recommended
– ANSI/UL 10B-2009 Fire Tests of Door As-
Selection and Usage Guide for Standard Steel
semblies
Doors shall be used as a guide. This Standard
shall not act as an obstruction to the develop- – ANSI/UL 10C-2009 Positive Pressure Fire
ment of new, modified or improved products Tests of Door Assemblies
that meet the intent of this specification. – ANSI/UL 1784-2009 Air Leakage Tests of
This specification covers sizes, design, mate- Door Assemblies
rials, general construction requirements and – ANSI/NFPA 80-2010 Standard for Fire Doors
finishing of standard steel doors and frames. and Other Opening Protectives
SDI-100 is intended to define standard items
not subject to variations. The products defined – ANSI/NFPA 252-2012 Fire Tests of Door As-
in this standard have demonstrated successful semblies
performance to established test procedures and – ANSI/SDI A250.3-2007 (R2011) Test Proce-
physical usage (see Section 1.2). dure and Acceptance Criteria for Factory
It is the user’s responsibility to coordinate the Applied Finish Coatings for Steel Doors and
information contained herein with applicable Frames
building and/or fire code requirements. – ANSI/SDI A250.4-2011 Test Procedure and
1.2 Reference Documents Acceptance Criteria for Physical Endurance
for Steel Doors, Frames, Frame Anchors and
1.2.1 SDI Standards
Hardware Reinforcings
– SDI-108-2010 Recommended Selection and
– ANSI/SDI A250.6-2003 (R2009) Recom-
Usage Guide for Standard Steel Doors
mended Practice for Hardware Reinforcing
– SDI-111-2009 Recommended Details for on Standard Steel Doors and Frames
Standard Steel Doors, Frames, Accessories
– ANSI/SDI A250.7-1997 (R2002) Nomencla-
ture for Standard Steel Doors and Steel
– SDI-112-2008 Zinc Coated (Galvanized/ Frames
Galvannealed) Standard Steel Doors and
– ANSI/SDI A250.10-1998 (R2011) Test Pro-
Frames
cedure and Acceptance Criteria for Prime
– SDI-117-2009 Manufacturing Tolerances for Painted Steel Surfaces for Steel Doors and
Standard Steel Doors and Frames Frames
1
– ANSI/SDI A250.11-2012 Recommended Erec- shall be used as guides in the development of

tion Instructions for Steel Frames (Formerly the necessary product schedule.
SDI-105)
Classification — Level, Performance,
1.4
– ANSI/BHMA A156.115-2006 American Na- Model
tional Standard for Hardware Preparations
in Steel Doors and Steel Frames For each of the following levels and models,
doors, frames, frame anchors, and hardware
1.2.3 ASTM Standards reinforcings shall be provided to meet the re-
– ASTM A1008-2012 Standard Specification for quirements of the performance levels indicated
Steel Sheet, Cold-Rolled, Carbon, Structural, below. The material used in manufacturing
High-Strength Low-Alloy and High-Strength these products and components shall comply
Low-Alloy with Improved Formability with Tables 2, 3, and 4 of this document. The
physical performance levels are determined by
– ASTM A568-2011 Standard Specification testing assemblies in accordance with ANSI/
for Steel, Sheet, Carbon, Structural, and
SDI A250.4, Test Procedure and Acceptance
High-Strength, Low-Alloy, Hot-Rolled and
Criteria for Physical Endurance for Steel Doors,
Cold-Rolled, General Requirements for
Frames, Frame Anchors and Hardware Rein-
– ASTM A1011-2012 Standard Specification forcings. See Section 2.3.1.1 and 2.3.1.2 for a
for Steel, Sheet and Strip, Hot-Rolled, Car- description of Full Flush and Seamless.
bon, Structural, High-Strength Low-Alloy
and High-Strength Low-Alloy with Improved Level 1
Formability and Physical Performance Level C
– ASTM A653-2011 Standard Specification for Standard-duty 1-3/8″ (34.9 mm) and 1-3/4″
Steel Sheet, Zinc-Coated (Galvanized) or (44.5 mm)
Zinc-Iron Alloy-Coated (Galvannealed) by Model 1 – Full Flush
the Hot-Dip Process Model 2 – Seamless
– ASTM A879-2012 Standard Specification for

Steel Sheet, Zinc Coated by the Electrolytic Level 2
Process for Applications Requiring Designa- and Physical Performance Level B
tion of the Coating Mass on Each Surface Heavy-duty 1-3/4″ (44.5 mm)
– ASTM A924-2010 Standard Specification Model 1 – Full Flush
for General Requirements for Steel Sheet, Model 2 – Seamless
Metallic-Coated by the Hot-Dip Process
1.3
A p p rova l D raw i n g s a n d H a rdwa re Level 3
Schedules and Physical Performance Level A
It is intended that approval drawings will not Extra Heavy-duty 1-3/4″ (44.5 mm)
be required for these items and that the manu- Model 1 – Full Flush
facturer’s published details, together with this Model 2 – Seamless
standard, will provide all the needed informa- Model 3 – Stile and Rail
tion. When specified, shop drawings shall be
submitted for approval prior to manufacturing
and/or delivery of product to the site. They Level 4
shall show elevations of each door design, and Physical Performance Level A
door construction details, hardware locations, Maximum-duty 1-3/4″ (44.5 mm)
dimensions, and shapes of materials, anchor- Model 1 – Full Flush
age and fastening methods, door frame types Model 2 – Seamless
and details, and finish requirements. SDI-111,
Recommended Details for Standard Steel
1.5 Sizes
Doors, Frames, Accessories and Related Com-
ponents and ANSI/SDI A250.7 Nomenclature Standard doors and frames are sized to fit
for Standard Steel Doors and Steel Frames openings noted in Table 1.
2
Table 1 – Standard opening sizes
Widths* Ft-in 2′0″ 2′4″ 2′6″ 2′8″ 2′10″ 3′0″ 3′4″ 3′6″ 3′8″ 3′10″ 4′0″
mm 610 711 762 813 864 914 1016 1067 1118 1168 1219
* Sizes shown are for single doors only; equal pairs of doors use twice the width
indicated. Pairs of doors can consist of two unequal widths.
Heights 1-3/4″ Doors Ft-in 6′8″ 7′0″ 7′2″ 7′10″ 8′0″
mm 2032 2134 2184 2388 2438
1-3/8″ Doors Ft-in 6′8″ 7′0″ 7′2″
mm 2032 2134 2184
2 Products mum requirements for coatings having 0.4 oz/ft²

(122 g/m²), total both sides, i.e., A40 (ZF120).
2.1 General
See SDI-112 Zinc-Coated (Galvanized/Galvan-
2.1.1 Steel Specifications nealed) Standard Steel Doors and Frames for
further information.
All steel used to manufacture doors, frames,
anchors, and accessories shall meet at least 2.1.1.4 When zinc coated steel is specified for
one or more of the following requirements. anchors and accessories, and electrolytically
deposited zinc coated steel is provided, it shall
2.1.1.1 Cold rolled steel shall conform to ASTM
comply with ASTM A653 Standard Specification
A1008, Standard Specification for Steel Sheet,
for Steel Sheet, Zinc-Coated (Galvanized) or
Cold-Rolled, Carbon, Structural, High-Strength
Zinc-Iron Alloy-Coated (Galvannealed) by the
Low-Alloy and High-Strength Low-Alloy with
Hot-Dip Process. The minimum coating desig-
Improved Formability and A568, Standard
nation shall be A40 i.e., 0.4 oz/ft² (122 g/m2).
Specification for Steel, Sheet, Carbon, and
High-Strength, Low-Alloy, Hot-Rolled and Cold- 2.1.2 Fire Doors and Related Frames
Rolled, General Requirements for.
2.1.2.1 Fire Doors and Frames
2.1.1.2 Hot rolled, pickled and oiled steel shall
When specified for either insurance rating pur
comply with ASTM A1011, Standard Specifi-
poses or for compliance to building codes,
cation for Steel, Sheet and Strip, Hot-Rolled,
manufacturers shall provide the type of fire door
Carbon, Structural, High-Strength Low-Alloy
and frame assembly that has been investigated
and High-Strength Low-Alloy with Improved
and/or successfully fire tested in accordance
Formability and A568, Standard Specifica-
with the latest revision of ANSI/UL10B, Fire
tion for Steel Sheet, Carbon, Structural, and
Tests of Door Assemblies, ANSI/UL10C, Posi-
High-Strength, Low-Alloy, Hot-Rolled and Cold-
tive Pressure Fire Tests of Door Assemblies, or
Rolled, General Requirements for.
ANSI/NFPA 252, Fire Tests of Door Assemblies.
2.1.1.3 When specified, hot dipped zinc coated The assembly shall be identified by labels and/or
steel shall be of the alloyed type and comply an approved identification marking of an agency
with ASTM A924, Standard Specification for accepted by the authority having jurisdiction.
General Requirements for Steel Sheet, Metallic- The door label shall indicate the applicable fire
Coated by the Hot-Dip Process and A653, test rating for the door construction furnished.
Standard Specification for Steel Sheet, Zinc- See Appendix “A”, and SDI-118, Basic Fire Door,
Coated (Galvanized) or Zinc-Iron Alloy-Coated Fire Door Frame, Transom/Sidelight Frame, and
(Galvannealed) by the Hot-Dip Process. The Window Frame Requirements for additional
coating weight shall meet or exceed the mini- information.
3
2.1.2.2 Smoke Control Doors of a type recommended for use on prime-painted

steel. Consult the door and frame manufac-
When specified, manufacturers shall provide the
type of fire door and frame assembly that has turer’s literature for description of primer used.
been investigated and/or successfully tested The manufacturer of the finish paint should
in accordance with the latest revision of ANSI/ verify compatibility with the primer.
UL1784 Air Leakage Tests of Door Assemblies. 2.1.6 Tolerances
See SDI-118, Basic Fire Door, Fire Door Frame,
Transom/Sidelight Frame, and Window Frame SDI-117, Manufacturing Tolerances for Stan-
Requirements for additional information. dard Steel Doors and Frames shall apply to
the standard steel doors and frames specified.
2.1.2.3 Steel Astragals on Fire Doors
Where required by a manufacturer’s listing or 2.1.7 Test Procedures
ANSI/NFPA 80, Standard for Fire Doors and The products furnished under this standard shall
Other Opening Protectives, a steel overlapping have demonstrated successful performance to
astragal shall be provided. the following established standard test methods:
2.1.2.4 Louvers for Fire Doors ANSI/SDI A250.3 – Test Procedure and Ac-
When specified, fire doors shall be provided ceptance Criteria for Factory Applied Finish
with fire labeled louvers. See SDI-118, Basic Coatings for Steel Doors and Frames.
Fire Door, Fire Door Frame, Transom/Sidelight
Frame, and Window Frame Requirements for ANSI/SDI A250.4 – Test Procedure and Ac-
acceptable labeling methods. ceptance Criteria for Physical Endurance for
Steel Doors, Frames, Frame Anchors and
2.1.3 Prime Finish Hardware Reinforcings.
Doors and frames shall be thoroughly cleaned ANSI/SDI A250.10 – Test Procedure and
and chemically treated to ensure paint adhesion.
Acceptance Criteria for Prime Painted Steel
All surfaces of the door and frame exposed
Surfaces for Steel Doors and Frames.
to view shall receive a factory applied coat of
rust inhibiting primer, either air-dried or baked- 2.1.8 Design Clearances
on. The finish shall meet the requirements for
acceptance stated in ANSI/SDI A250.10, Test 2.1.8.1 The clearance between the door and
Procedure and Acceptance Criteria for Prime frame shall be a maximum of 1/8″ (3.2 mm) in
Painted Steel Surfaces for Steel Doors and the case of both single swing and pairs of doors.
Frames. Proper job site storage as outlined in 2.1.8.2 The clearance between the meeting
Section 4.1, shall be followed.
edges of pairs of doors shall be 3/16″ (4.8 mm)
2.1.4 Factory Applied Finish Paint ± 1/16″ (1.6 mm). For fire rated applications, the
When specified, doors and frames shall be clearances between the meeting edges of pairs
finish painted on all surfaces of the door and of doors shall be 1/8″ (3.2 mm) ± 1/16″ (1.6 mm).
frame exposed to view. The factory applied finish 2.1.8.3 The clearance measured from the
paint shall meet the performance requirements bottom of the door to the bottom of the frame
and acceptance criteria as stated in ANSI/ (Undercut) shall be a maximum of 3/4″ (19.1 mm)
SDI A250.3, Test Procedure and Acceptance
unless otherwise specified. Fire door undercuts
Criteria for Factory Applied Finish Coatings
shall comply with ANSI/NFPA 80, Standard for
for Steel Doors and Frames. Consult individual
Fire Doors and Other Opening Protectives.
manufacturers for product availability and color
selection. Proper job site storage, as outlined 2.1.8.4 The clearance between the face of
in Section 4.1, shall be followed. the door and the stop shall be 1/16″ (1.6 mm)
2.1.5 Field Applied Finish Paint to 3/32″ (2.4 mm).
Unless doors and frames are factory finish 2.1.8.5 All clearances shall be, unless other-
painted, a compatible coat of finish paint shall wise specified in this document, subject to a
be applied in the field. The finish paint shall be tolerance of ±1/32″ (0.8 mm).
4
Table 2 – Steel thickness / door faces
Minimum Thickness
Level Model MSG No. (1)
Inches mm
1 0.032 0.8 20
1
2 0.032 0.8 20
1 0.042 1.0 18
2
2 0.042 1.0 18
1 0.053 1.3 16
3 2 0.053 1.3 16
3 See Sec. 2.3.3 Construction Features 16
1 0.067 1.7 14
4
2 0.067 1.7 14
(1)
2.1.9 Steel Thickness (see Table 2) 2.3.1.3 Door Edges

2.2
Manufacturers Standard Gage (MSG) Door edges shall be fabricated utilizing the
vs. Minimum Steel Thickness following different profiles:
The minimum steel thickness for each specific • Square Edge – edge of door which is 90°
gage is derived from the published figures of to the face
Underwriters Laboratories LLC, and shall be
used for reference purposes only. • Beveled Edge – edge of a door which is
not at a 90° angle to the face of the door
2.3 Construction Features (standard bevel is 1/8″ (3.2 mm) in 2″ (50.8
2.3.1 Door Faces and Edge mm) – narrow side of door is in contact
with stop of frame when door is closed
2.3.1.1 Full Flush
Unless specified, door edges will be manu-
Each door face shall be formed from a single factured in accordance with manufacturer’s
sheet of steel of a thickness as defined by standard for that model.
Table 2. There shall be no visible seams on
the surface of the faces. A full height vertical 2.3.1.4 End Channels or Closures
seam is permitted on door edges. The top and bottom of the door shall be closed
2.3.1.2 Seamless with either flush or inverted channels or clo-
sures. The channels or closures shall have a
In addition to the requirements for full flush minimum material thickness of 0.042″ (1.0 mm).
doors, no visible seams are permitted along the
vertical edges. One of the following methods, 2.3.1.5 Decorative Faces
at the discretion of the manufacturer, shall be When specified, door faces shall be fabricated
used when a seamless door is specified:
of textured and/or embossed steel. These ma-
• vertical seam edge filled, dressed smooth terials shall meet the requirements of Table 2.
• intermittently welded seams, edge filled, 2.3.2 Core Construction
dressed smooth
The core design shall be at the discretion of
• continuously welded seam dressed smooth the manufacturer.
5
Doors of the following core designs have met 2.4 Frames

the performance requirements of the documents
2.4.1 General
listed under Section 2.1.7:
Provide steel frames for doors, transoms,
• KraftPaper Honeycomb sidelights, mullions, interior glazed panels and
• Polystyrene other openings, where indicated. Provide either
knockdown field assembled type, or welded unit
• Polyurethane type frames as specified.
• Mineral Board Performance tests shall be conducted on
3-sided door frames and corresponding door
• Vertical Steel Stiffeners
designs. The variety and complexity of openings
This shall not restrict the development of alter- containing transom, sidelights, or other such
nate core materials that meet the performance configurations preclude the use of these test
requirements specified above. methods on such designs.
Construction Features – Stile and

2.3.3 ANSI/SDI A250.7, Nomenclature for Standard
Steel Doors and Steel Frames and SDI-111,
Rail – Flush Panel
Recommended Details for Standard Steel
Stiles and rails shall be a minimum of 0.053″ Doors, Frames, Accessories and Related
(1.3 mm) in thickness and shall be cold rolled or Components shall be used as guides in the
galvanized steel. Door corners shall be mitered development of frame details.
or butted. Mitered joints shall be internally re- 2.4.1.1 Knockdown Frames
inforced, welded and ground smooth such that
Unless otherwise specified, frames shall be
no miter joints appear on door faces. Where
supplied as knockdown, and shall have rigidly
specified, intermediate rails shall be butted
interlocked frame joints so as to maintain align-
and either permanently mechanically fastened ment and assure performance of completed
or internally welded to door stiles. Butted joint frames when field assembled. These frames
seams shall remain visible. Center panels shall can consist of either single rabbet or double
be made using cold rolled or galvanized steel rabbet profiles.
with a minimum thickness of 0.042″ (1.0 mm),
2.4.1.2 Frames for Existing Drywall Open-
and shall be reinforced with manufacturer’s
ings
standard core material. Panel faces shall be
flush with perimeter surfaces and shall be When frames are specified for installation in
joined to abutting perimeter members by weld- existing drywall construction they shall be of
ing or permanent mechanical fastening. Where the slip-on drywall type. These frames are not
available with welded corners. A butted wall
specified, panels shall be recessed in lieu of
frame with existing wall anchors may also be
flush. Recessed panels shall be reinforced and
installed in existing drywall wall construction.
fastened as specified for flush panels. Hardware This frame type is available with welded corners.
reinforcements shall be as specified in Table 4
and located as specified in Table 5. 2.4.1.3 Welded Frames
2.3.4 Vision Lights Welded frames required to comply with this

standard shall be supplied as face welded un-
When doors are specified to contain glazed less otherwise specified as either full profile
openings, the manufacturer’s standard light kit welded, fully welded or continuously welded.
shall be supplied unless otherwise specified. Face Welded: The joint between the head and
2.3.5 Louvered Doors jamb faces shall be completely arc welded along
their length either internally or externally. The
When specified, doors shall be provided with remaining elements of the frame profile, i.e.,
louvers. SDI-111C, Recommended Louver De- soffit, stops, rabbets, are not welded. Face
tails for Standard Steel Doors shall be used as joints shall be ground and finished smooth
a guide in detailing/specifying louvers. with no visible seam. Face joints at meeting
6
Table 3 – Minimum steel thickness / frames
Thickness
Level MSG No. (1)
inches mm
1 0.042 1.0 18
2 0.053 1.3 16
3 0.053 1.3 16
4 0.067 1.7 14
(1)
mullions or between mullions and other frame rigid mechanical connection, so as to maintain
members shall be completely arc welded ex- alignment of parts and assure performance of
ternally, ground, and finished smooth. completed frames when field assembled. When
specified, vertical mullions shall be provided
Full Profile Welded: (Also specified as fully
with floor anchors.
welded or continuously welded.) The joints
between all elements of the head and jamb 2.4.4 Frame Anchors for Wall Conditions
profiles, i.e., soffit, stops, rabbets, faces and
Provide frames, other than slip-on drywall type,
returns, shall be completely arc welded. Faces
with a minimum of three anchors per jamb suit-
and returns may be arc welded either internally
able for the adjoining wall construction. Provide
or externally, all other frame elements shall
anchors of not less than 0.042″ (1.0 mm) in
be welded internally. Faces and returns shall
thickness or 0.167″ (4.2 mm) diameter wire.
be ground and finished smooth with no visible
Frames OVER 7′6″ (2286 mm) in height shall
seam. The joint at other frame elements shall
be provided with additional anchors.
appear as a hairline seam on the external side.
Face joints at meeting mullions or bet ween 2.4.4.1 Slip-On Drywall Frame Anchors
mullions and other frame members shall be
Slip-on drywall frames shall have an anchoring
completely externally welded on the faces only,
system that is an integral par t of the frame,
welds shall be ground and finished smooth. The
and allows installation of the frame after the
meeting joints of other mullion profile elements
wall has been constructed and finished.
are not welded.
2.4.4.2 Base Anchors
Welded frames shall be provided with a tem-
porary spreader bar for shipping and handling Provide frames, other than slip-on drywall type,
purposes only. This temporary spreader bar with base anchors that are not less than 0.042″
shall be removed and a setting spreader, sup- (1.0 mm) in thickness for attachment to the
plied by the installer, shall be used for instal- floor. For wall conditions that do not allow for
lation of the frame. See ANSI/SDI A250.11, the use of a floor anchor, an additional jamb
Recommended Erection Instructions for Steel anchor shall be specified.
Frames for details.
2.4.5 Glazing Beads
Manufacturers Standard Gages for
2.4.2
On frame assemblies that incorporate glazed
Frames
openings, the frame shall be provided with
Table 3 shall be used to determine the proper glazing beads designed to receive the glazing
gage thickness for the corresponding door materials specified. The glazing beads shall be
levels. butted at the corners. Glazing beads shall be
of snap-on or screw-applied design.
2.4.3
Frames with Mullions and Transom
Bars 2.4.6 Terminated Stops
Mullions and transom bars shall be joined to When specified, stops for interior door frames
adjacent members by welding (see 2.4.1.3) or by shall be terminated above the floor 6″ (152.4
7
Table 4 – Minimum hardware reinforcing thickness
Door Frame
Hardware Item
inches mm MSG No. (6) inches mm MSG No. (6)
Mortise Hinge 1-3/8″ [34.9 mm] Door (1) 0.093 2.3 12 0.093 2.3 12
Mortise Hinge 1-3/4″ [44.5 mm] Door (1) (2) 0.123 3.1 10 0.123 3.1 10
Mortise Lock or Deadbolt (1) 0.067 1.7 14 0.067 1.7 14
Bored Lock or Deadbolt (1) 0.067 1.7 14 0.067 1.7 14
Flush Bolt Front (1) 0.067 1.7 14 0.067 1.7 14
Surface Bolt (3) 0.067 1.7 14 0.067 1.7 14
Surface Applied Closer (4) 0.067 1.7 14 0.067 1.7 14
Hold Open Arm (3) 0.067 1.7 14 0.067 1.7 14
Pull Plates and Bar (3) 0.053 1.3 16 0.053 1.3 16
Surface Exit Device (3) 0.067 1.7 14 0.067 1.7 14
Floor Checking Hinge 0.167 4.2 7 0.167 4.2 7
Pivot Hinge 0.167 4.2 7 0.167 4.2 7
Continuous Hinges (5) Not Required Not Required
Kick / Push Plate Not Required Not Required

Note: The minimum steel thickness for each specific gage is derived from the published figures of
Underwriters Laboratories LLC.
(1)
Thinner steel may be employed as long as tapped holes used for mounting the hardware are
extruded to produce an equivalent number of threads.
(2)
If reinforcing is angular or channel shaped, 0.093″ (2.3 mm) is permitted.
(3)
When reinforcing is omitted, thru-bolting via the use of spacers or sex-bolts is required.
(4)
Reinforcement shall occur on both sides.
(5)
Refer to ANSI/SDI A250.6, Recommended Practice for Hardware Reinforcing on Standard Steel
Doors and Frames.
(6)
mm) standard, measured from frame bottom 3.1.1 Mortise Hardware Preparations

to bottom of terminated stop. The stop is cut
Doors and frames shall be reinforced, drilled
at a 45° or 90° angle and closed with a steel
and tapped to receive mortised hinges, locks,
filler plate welded in place. Terminated stops latches, and flush bolts as required. Prepara-
on frames for lightproof doors, sound-rated tion shall be in accordance with ANSI/BHMA
doors, double egress, or lead-lined doors are A156.115 American National Standard for
not available. Hardware Preparations in Steel Doors and Steel
Frames and ANSI/SDI A250.6, Recommended
3 Hardware Preparation Practice for Hardware Reinforcing on Standard
3.1 Reinforcings Steel Doors and Frames where applicable.
Provide minimum hardware reinforcing gages as 3.1.2 Surface Applied Hardware

noted in Table 4 and ANSI/SDI A250.6, Recom- When specified, doors and frames shall be
mended Practice for Hardware Reinforcing on reinforced for surface applied hardware. Drilling
Standard Steel Doors and Frames. and/or tapping shall be completed by others.
8
3.1.3 Function Holes 4 Storage, Handling, and Installation

The preparation for locks and/or exit devices 4.1 Jobsite Storage
shall include reinforcements (as shown in
All doors and frames shall be stored vertically
Table 4) and function holes. Trim and/or mount-
under cover. The units shall be placed on
ing holes are not included. at least 4″ (102 mm) high wood sills or in a
3.1.4 Anchor or Pivot Reinforced Hinges manner that will prevent rust or damage. The
use of non-vented plastic or canvas shelters
Where specified, the appropriate recessing and that can create a humidity chamber shall be
reinforcing shall be provided. Mounting holes avoided. A 1/4″ (6.3 mm) space between the
shall be field drilled and tapped by others. doors shall be provided to promote air circula-
3.1.5 Hinge Preparations tion. If the wrapper on the door becomes wet,
it must be removed immediately. Proper jobsite
See Table 5. Doors up to and including 7′6″ storage is extremely important in maintaining
(2184 mm) high require a minimum three (3) the quality and integrity of the factory applied
hinge preparations. Doors over 7′6″ (2286 mm) paint. Improper Storage of material will have
high require a minimum four (4) hinge prepara- an adverse effect on the factory applied paint’s
tions. Exception: 1-3/8″ (34.9 mm) thick, 6′8″ ability to meet the requirements of ANSI/ SDI
(2032 mm) high non-fire rated doors shall be A250.10, Test Procedure and Acceptance Cri-
prepared for a minimum of two hinges. teria for Prime Painted Steel Surfaces for Steel
Doors and Frames or ANSI/SDI A250.3, Test
3.1.6 Hardware Locations Procedure and Acceptance Criteria for Fac-
Hardware shall be located in accordance with tory Applied Finish Coatings for Steel Doors
Table 5. and Frames.
Other items of hardware shall be located accord- 4.2 Frame Installation

ing to the door and/or hardware manufacturer’s 4.2.1 Frames shall be installed plumb, level,
directions. This includes the door closers, floor rigid and in true alignment as recommended
hinges, overhead door holders, pocket pivot, in ANSI/SDI A250.11 Recommended Erection
and most specialized-purpose hardware. Instructions for Steel Frames.
Table 5 – Hardware locations
Locks, Latches, Roller Latches and Double

Handle Sets 38″ – 42″ (965 mm – 1067 mm) Centerline of Lock Strike from Bottom
of Frame
Rim and Mortise Panic Devices
Cylindrical and Mortise Deadlocks (1) 48″ (1219 mm) to Centerline of Strike from Bottom of Frame
Push Plates Centerline 45″ (1143 mm) from Bottom of Frame
Pull Plates Centerline of Grip @ 42″ (1067) from Bottom of Frame
Combination Push Bar Centerline of 42″ (1067 mm) from Bottom of Frame
Centerline of Lower Base is 45″ (1143 mm) from Bottom of Frame with
Hospital Arm Pull
Grip Open at Bottom
Up to 11-3/4″ (298.5 mm) from Rabbet Section of Frame to Centerline

Top
of Hinge
Hinges
Bottom Up to 13″ (330.2 mm) from Bottom of Frame to Centerline of Hinge
Intermediate Equally Spaced Between Top and Bottom Hinges

(1)
Cylindrical and Mortise Deadlock strikes shall be located at 48″ (1219 mm) from the bottom of the
frame unless otherwise specified.
9
All frames, other than drywall slip-on types, ances as specified in Section 2.1.8. Shimming
shall be fastened to the adjacent structure so shall be performed by the installer as needed
as to retain their position and stability. Slip-on to assure the proper clearances are achieved.
drywall frames shall be installed in prepared
4.4 Hardware Installation
wall openings in accordance with manufacturer’s
instructions. Installation of hardware items shall be in ac-
cordance with the hardware manufacturer’s
4.2.2 Where grouting is required in masonry
recommendations and templates. ANSI/SDI
installations, frames shall be braced or fastened
A250.6, Recommended Practice for Hardware
in such a way that will prevent the pressure of
Reinforcing on Standard Steel Doors and
the grout from deforming the frame members.
Frames shall be consulted for other pertinent
Grout shall be mixed to provide a 4″ (102
information.
mm) maximum slump consistency and hand
troweled into place. Grout mixed to a thinner, 4.5 Installation of Factory Applied Finish
“pumpable” consistency shall not be used. Painted Materials
Excess water from thin consistency grout will
In addition to storage and handling precautions
cause premature rusting of steel frames and
noted in Section 4.1, it is IMPERATIVE that
probable deformation or discoloration of certain
the work of all other rough trades MUST be
wall constructions. Standard mortar protection
completed prior to the installation of factory
in frames is not intended for thin consistency
applied finished painted product.
grout or drywall compound.
4.6 Door and Frame Maintenance
Steel Frames, including fire rated frames do
not require grouting. GROUTING SHALL NOT It is the responsibility of the installer or end
BE USED FOR FRAMES INSTALLED IN DRY- user to properly maintain the doors and frames
WALL WALLS. in accordance with SDI-124, Maintenance of
Standard Steel Doors and Frames.
4.3 Door Installation
4.7 Door and Frame Repair
Doors shall be installed and fastened to maintain
alignment with frames to achieve maximum op- Any repair required to either the door or frame
erational effectiveness and appearance. Doors in a fire rated opening shall be conducted in
shall be adjusted to maintain perimeter clear- accordance with NFPA 80.
10
Appendix A
(informative)
Fire Door Considerations
Fire door testing

There are two primary fire test methods that are used to establish the fire ratings of doors. The
first is ANSI/UL 10B, Fire Tests of Door Assemblies, and is referred to as neutral pressure; the
second is ANSI/UL 10C, Positive Pressure Fire Tests of Door Assemblies, and is referred to as
positive pressure.
The difference between the two test methods concerns the location of a neutral pressure plane
in the test furnace. In the late 1990’s the test method required in building codes changed to a
positive pressure test method. This change was adopted in the Uniform Building Code (UBC) and
the International Building Code (IBC) for swinging-type fire doors.
Fire doors required to be tested by either method may be specified by calling out the test method
or by indicating that the product must meet a specific section of a model building code.
These tests incorporate two phases: A fire test phase utilizing an established time-temperature
curve and a structural integrity phase utilizing a hose stream test conducted under established
time-pressure criteria determined by exposure time and area of the assembly. To be a valid fire
door assembly, the unit must pass both phases of the test.
In certain instances as permitted by building codes, the integrity portion (hose stream) is deleted.
The deletion of this requirement negates the assembly’s use as a true fire door.
The fire test procedures also include a measurement of unexposed surface temperatures at regu-
lar intervals up to 30 minutes.
The fire test does not address or measure the amount of smoke leakage through the assembly.
For this criteria, ANSI/NFPA-105 Standard for the Installation of Smoke Door Assemblies and
Other Opening Protectives and ANSI/UL 1784 Air Leakage Tests of Door Assemblies should be
consulted.
Fire door ratings

Swinging steel doors and frames are commonly tested as flush (non-glazed) units for a 3-hour
time period. This allows their usage for all lower fire protection ratings. Lights in doors may be
permitted based on the performance of flush doors when evaluated with the testing database and
experience of the test lab or certifying agency.
Typical hourly ratings for swinging steel fire doors are 3-hours, 1-1/2-hours, 3/4-hours, and 1/3-hour.
Usage of these ratings is as follows:
3-Hour — Openings in fire walls that divide a single building into fire areas, normally 4-hour
rated walls.
1-1/2-Hour — Openings in enclosures of vertical communications through buildings and in 2-hour
partitions providing horizontal fire separations. These may also be used as non-glazed doors for
openings in exterior walls subject to severe fire exposure from outside of the building.
3/4-Hour — Openings in 1-hour rated (or less) partitions bet ween rooms and corridors, or other
separation of occupancy. With certain light restrictions these may also be used in exterior walls
subject to moderate or light fire exposure from outside of the building. The 3/4-hour fire door may
also be used as a smoke and draft control door.
11
1/3-Hour (20 minute) — Doors of this rating are used for the protection of openings bet ween
living quarters and corridors and where smoke control is a primary concern. They may also be
used as a smoke partition across corridors.
Fire door temperature rise

In addition, a temperature rise rating may be required by building codes in areas such as en-
closures of vertical communications or in areas of storage for hazardous materials. Temperature
rise ratings indicate the maximum temperature, above ambient, of the unexposed surface at 30
minutes into the fire test. Three ratings, 250°F (121°C), 450°F (232°C), or 650°F (343°C) are
recognized, with the 250°F (121°C) rating being the most thermally efficient. Ratings over 650°F
(343°C) are not recognized as temperature rise doors.
Fire door labeling

Doors and frames may bear labels or marks of a recognized third party certification agency, ac-
ceptable to the authority having jurisdiction. Fire door labels must indicate the hourly rating and
either the latch throw for single point locks or must bear a notation “Fire door to be equipped with
fire exit hardware”. Fire door labels may also indicate the temperature rise rating.
Door labels may be of metal (installed by welding, riveting, adhesive or drive screw) or of mylar.
The existence of a label is the only method of verification that the door is rated.
Frame labels, except in specific instances, do not indicate hourly ratings. Fire door frames assume
the rating of the fire door installed or a rating that corresponds to the rating of the wall in which
it is installed, whichever is lesser.
Frame labels may be of metal (installed by welding, riveting, or drive screw), mylar, or may be
embossed into the frame.
Door and/or frame labels may be of the same or different certifying agencies. A door assembly
may consist of labeled components of different manufacturers.
Other fire door considerations

The effectiveness of a fire door assembly is dependent on the use of listed or labeled items for
all components. These may include glazing material, locks, hinges, closers, latches, light frames,
other hardware items, etc. The substitution of a non-rated component or one that is rated less
than the intended fire protection rating of the assembly results in a corresponding decrease in
rating or the loss of the rating in its entirety.
For further information, see SDI-118 Basic Fire Door, Fire Door Frame, Transom/Sidelight Frame,
and Window Frame Requirements or ANSI/NFPA 80 Standard for Fire Doors and Other Opening
Protectives.
For information on fire doors used in a means of egress consult NFPA-101 Life Safety Code®.
12
Appendix B
(informative)
General Considerations
Steel coating types

ASTM A924, Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by
the Hot-Dip Process and A653, Standard Specification for Steel Sheet, Zinc-Coated (Galvanized)
or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process provide specifications for both
galvannealed (A Type) and Galvanized (G Type) coatings. For purposes of this standard, G type
coatings are not recommended due to problems related to paint adhesion and welding. In addition,
heavier coating weights, i.e., G60 and G90 are known to experience cracking and peeling of the
coating resulting in potential performance failures under ANSI/SDI A250.10, Test Procedure and
Acceptance Criteria for Prime Painted Steel Surfaces for Steel Doors and Frames and ANSI/SDI
A250.3, Test Procedure and Acceptance Criteria for Factory Applied Finish Coatings for Steel
Doors and Frames.
Steel thickness
When ordering steel directly from the mill, manufacturers order sheet and coil to a minimum deci-
mal thickness and not a nominal gage. This thickness is generally at the low end of the range for
a specific gage. For example, the nominal thickness of 16 gage is 0.059″ (1.5 mm). The thickness
tolerance permitted by ASTM A568, Standard Specification for Steel, Sheet, Carbon, Structural,
and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for, is ± .006″
(0.15 mm). Therefore the minimum ordering dimension would then become 0.053″ (1.3 mm) as
shown in Table 2. These minimum values meet the requirements of Underwriters Laboratories
LLC. Steel gages, or MSG numbers may be used for reference purposes only.
Thermal bow
Thermal bow is a condition which may occur in metal doors due to an inside / outside temperature
differential. It is warping of the top and bottom of the lock edge of the door either toward or away
from the frame stop. This condition may result in force on the latch that increases the difficulty
of opening the door and may increase the air leakage of the opening.
This condition, and the degree of bowing, depends on the door color, construction, length of ex-
posure, temperature, etc. Thermal bow can often be alleviated by painting the exposed surface a
light color. In some cases of extreme cold, this condition may also occur in reverse.
Aesthetics
The production of steel doors and frames relies on a variety of manufacturing processes including
spot welding, projection welding, arc welding ground smooth, grinding, filling, etc. These processes
may result in a show-through after application of finished paint. These characteristics are inherent
in production and are not to be considered as manufacturing defects.
The show-through characteristics increase as the paint gloss increases. This standard recom-
mends a maximum paint gloss rating of 20% reflectance, measured using a 60° gloss meter,
which should be suitable for most applications. Translucent paints may emphasize show-through
characteristics and their use is not recommended. The 20% reflectance is equivalent to a Master
Painters Institute (MPI) gloss rating description of a traditional “eggshell-like” finish.
13
Water penetration
Borrowed light, transom, sidelight, and combination transom sidelight frames are not factory sealed
to prevent water penetration. In situations where this is a concern, the contractor must seal all
joints that are exposed to the elements after the frame assembly is installed.
Whenever possible, it is strongly recommended that glass and glazing be installed on the exterior
rabbet of the frame assembly, which will help act as a deterrent to water penetration. It should
be noted that a fully welded corner does not ensure a water tight condition.
The member companies of the hollow metal industry cannot control the workmanship associated
with the frame installation and therefore, this work must be specified in the installation/glazing/
caulking section of the specifications. It is the responsibility of the contractor to assure all steps
are taken by the installer, glazer, or others to prevent water penetration.
14
Appendix C
(informative)
Section 08100 Standard Hollow Metal Doors and Frames

(intended as a sample specification)
Part 1: General
1.01 Work included
A. Fur nish only standard hollow metal doors, frames, sidelights and borrowed lights as
specified and shown on plans and schedules.
B. Related sections
1. Section 08700 — Finish hardware
2. Section 09900 — Painting
3. Section 08800 — Glass & glazing
1.02 References
A. SDI standards
1. SDI-106-1999 Recommended Standard Door Type Nomenclature
2. SDI-108-2010 Recommended Selection and Usage Guide for Standard Steel
Doors
3. SDI-111-2009 Recommended Details for Standard Steel Doors, Frames, Acces-
sories and Related Components
4. SDI-112-2008 Zinc-Coated (Galvanized/Galvannealed) Standard Steel Doors and
Frames
5. SDI-117-2009 Manufacturing Tolerances for Standard Steel Doors and Frames
6. SDI-118-2012 Basic Fire Door Requirements
7. SDI-124-2011 Maintenance of Standard Steel Doors and Frames
B. ANSI standards
1. ANSI/UL 10B-2009 Fire Tests of Door Assemblies
2. ANSI/UL 10C-2009 Positive Pressure Fire Tests of Door Assemblies
3. ANSI/UL 1784-2009 Air Leakage Tests of Door Assemblies
4. ANSI/NFPA 80-2010 Standard for Fire Doors and Other Opening Protectives
5. ANSI/NFPA 252-2012 Fire Tests of Door Assemblies
6. ANSI/SDI A250.3-2007 (R2011) Test Procedure and Acceptance Criteria for Factory
Applied Finish Coatings for Steel Doors and Frames
7. ANSI/SDI A250.4-2011 Test Procedure and Acceptance Criteria for Physical Endur-
ance for Steel Doors, Frames, Frame Anchors and Hardware Reinforcings
8. ANSI/SDI A250.6-2003 (R2009) Recommended Practice for Hardware Reinforcing
9. ANSI/SDI A250.7-1997 (R2002) Nomenclature for Standard Steel Doors and Steel
Frames
10. ANSI/SDI A250.10-1998 (R2011) Test Procedure and Acceptance Criteria for Prime
Painted Steel Surfaces for Steel Doors and Frames
15
11. ANSI/SDI A250.11-2012 Recommended Erection Instructions for Steel Frames (For-
merly SDI-105)
12. ANSI/BHMA A156.115-2006 American National Standard for Hardware Preparations
in Steel Doors and Steel Frames
C. ASTM standards
1. ASTM A1008-2012 Standard Specification for Steel Sheet, Cold-Rolled, Carbon,
Structural, High-Strength Low-Alloy and High-Strength Low-Alloy with Improved
Formability
2. ASTM A568-2011 Standard Specification for Steel, Sheet, Carbon, Structural, and
High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
3. ASTM A1011-2012 Standard Specification for Steel Sheet and Strip, Hot-Rolled, Car-
bon, Structural, High-Strength Low-Alloy and High-Strength Low-Alloy with Improved
Formability
4. ASTM A653-2011 Standard Specification for Steel Sheet, Zinc-Coated (Galvanized)
or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
5. ASTM A879-06 Standard Specification for Steel Sheet, Zinc Coated by the Electro-
lytic Process for Applications Requiring Designation of the Coating Mass on Each
Surface
6. ASTM A924-2010 Standard Specification for General Requirements for Steel Sheet,
Metallic-Coated by the Hot-Dip Process
1.03 Quality assurance
A. Manufacturer shall meet or exceed all standards as noted in Section 2.01 references.
B. Fire rated assemblies shall be manufactured in accordance with [Underwriters Laborato-
ries] [Intertek Testing Services] [Factory Mutual] established procedures and shall bear
the appropriate labels for each application.
C. No product shall be manufactured prior to receipt of approved hardware schedule and
templates.
1.04 Submittals
A. Shop drawings, if required, shall show all openings in the door schedule and/or the draw-
ings.
B. When required, provide details of door design, door construction details and methods of
assembling sections, hardware locations, anchorage and fastening methods, door frame
types and details, and finish requirements.
1.05 Delivery, marking and storage
A. Where specified, all products shall be marked with architects opening number on all
doors, frames, misc. parts and car tons.
B. All materials upon receipt shall be inspected for damage, and the shipper and supplier
notified if damage is found.
C. All doors and frames shall be stored vertically under cover. The units shall be placed on
at least 4″ (102 mm) high wood sills or in a manner that will prevent rust or damage. The
use of non-vented plastic or canvas shelters that can create a humidity chamber shall
be avoided.
D. A 1/4″ (6.3 mm) space between the doors shall be provided to promote air circulation. If
the wrapper on the door becomes wet, it must be removed immediately.
16
1.06 Warranty
1.07 [See manufacturer’s warranty]
Part 2: Product
2.01 Materials
2.02 All steels used to manufacture doors, frames, anchors, and accessories shall meet at least
one or more of the following requirements:
A. Cold rolled steel shall conform to ASTM designations A1008, Standard Specification for
Steel Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High-Strength
Low-Alloy with Improved Formability and A568, Standard Specification for Steel, Sheet,
Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General
Requirements for.
B. Hot rolled, pickled and oiled steel shall comply with ASTM designations A1011, Standard
Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength
Low-Alloy and High-Strength Low-Alloy with Improved Formability and A568, Standard
Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled
and Cold-Rolled, General Requirements for.
C. Hot dipped zinc coated steel shall be of the alloyed type and comply with ASTM designa-
tions A924, Standard Specification for General Requirements for Steel Sheet, Metallic-
Coated by the Hot-Dip Process and A653, Standard Specification for Steel Sheet, Zinc-
Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process.
2.03 Frames
A. Interior frames
1. Level 1 for door model [1] [2] [0.042″ (1.0mm)] [0.053″ (1.3mm)] minimum steel
thickness for frames
2. Level 2 for door model [1] [2] [0.042″ (1.0mm)] minimum steel thickness for frames
3. Level 3 for door model [1] [2] [3] [0.053″ (1.3mm)] [0.067″ (1.7mm)] minimum
steel thickness for frames
B. Exterior frames
2. Level 2 for door model [1] [2] [0.053″ (1.3mm)] minimum steel thickness for frames
3. Level 3 for door model [1] [2] [3] [0.053″ (1.3mm)] [0.067″ (1.7mm)] minimum
steel thickness for frames
C. Frames shall be [knockdown type] [slip-on drywall type] [face welded type] [full profile
weld type]
D. Provide frames, other than slip-on drywall type with a minimum of three anchors per jamb
suitable for the adjoining wall construction. Provide anchors of not less than 0.042″ (1.0
mm) in thickness or 0.167″ (4.2 mm) diameter wire. Frames OVER 7′6 ″ (2286 mm) shall
be provided with an additional anchor per jamb.
E. Slip-on drywall frame anchors shall be as provided by the manufacturer to assure per-
formance.
17
F. Base anchors shall be provided, other than slip-on drywall type, with minimum thickness
of 0.042 ″ (1.0mm). For existing masonry wall conditions that do not allow for the use of
a floor anchor, an additional jamb anchor shall be provided.
G. All frames shall be fully prepared for all mortise template hardware and reinforced only
for surface mounted hardware. Drilling and/or tapping shall be completed by others.
H. Minimum hardware reinforcing gages shall comply with Table 4 of ANSI/SDI A250.8,
Specifications for Standard Steel Doors and Frames (SDI-100).
2.04 Doors
A. Doors shall meet at least one or more of the following requirements:

1. Level 1 – Standard duty 1-3/8″ (34.9 mm) and 1-3/4″ (44.5 mm)
Model 1 – Full flush
Model 2 – Seamless
2. Level 2 – Heavy duty 1-3/4″ (44.5 mm)
3. Level 3 – Extra heavy-duty 1-3/4″ (44.5 mm)
Model 3 – Stile and rail
4. Level 4 – Maximum-duty 1-3/4″ (44.5 mm)
B. Interior doors
Level [ I] [II] [III] [IV]
Model [1] [2] [3]
C. Exterior doors
Level [ I] [II] [III] [IV]
Model [1] [2] [3]
D. Door [and panel] construction
E. Face steel sheet shall meet at least one or more of the following requirements:
1. Level 1
Model 1 – 0.032″ (0.8mm) minimum thickness
2. Level 2
3. Level 3
18
4. Level 4
F. End closure: The top and bottom of the doors shall be closed with [flush] [inverted] chan-
nels or closures. The channels or closures shall have a minimum material thickness of
0.042″ (1.0mm).
G. Core: See ANSI/SDI A250.8, Specifications for Standard Steel Doors and Frames (SDI-
100), Section 2.3.2.
H. Door edge design: See ANSI/SDI A250.8, Specifications for Standard Steel Doors and
Frames (SDI-100), Section 2.3.1.3.
I. Minimum hardware reinforcing gages shall comply with Table 4 of ANSI/SDI A250.8,
Specifications for Standard Steel Doors and Frames (SDI-100).
J. Label requirements, steel astragals, louvers, vision lights – see ANSI/SDI A250.8, Speci-
fications for Standard Steel Doors and Frames (SDI-100) Section 2, Products.
2.05 Finishing
Prime finish: Doors and frames shall be thoroughly cleaned, and chemically treated to insure
maximum paint adhesion. All surfaces of the door and frame exposed to view shall receive a fac-
tory applied coat of rust inhibiting primer, either air-dried or baked-on. The finish shall meet the
requirements for acceptance stated in ANSI/SDI A250.10 Test Procedure and Acceptance Criteria
for Prime Painted Steel Surfaces for Steel Doors and Frames.
2.06 Design clearances
A. The clearance between the door and frame head and jambs shall be 1/8″ (3.2 mm) in the
case of both single swing and pairs of doors.
B. The clearance between the meeting edges of pairs of doors shall be 1/8″ (3.2 mm) to 1/4″
(6.3 mm), for fire rated doors 1/8″ (3.2 mm) ± 1/16″ (1.6 mm).
C. The clearance at the bottom shall be [3/4″ (19.1 mm)] [5/8″ (15.8 mm)].
D. The clearance between the face of the door and door stop shall be 1/16″ (1.6 mm) to 1/8″
(3.2 mm).
E. All clearances shall be, unless otherwise specified, subject to a tolerance of ± 1/32″
(0.8 mm).
Part 3: Execution
3.01 Installation
A. Frames shall be installed plumb, level, rigid and in true alignment as recommended in
ANSI/SDI A250.11, Recommended Erection Instructions for Steel Frames. All frames
other than slip-on types shall be fastened to the adjacent structure so as to retain their
position and stability. Drywall slip-on frames shall be installed in prepared wall openings
in accordance with manufacturer’s instructions.
B. Where grouting is required in masonry installations, frames shall be braced or fastened
in such a way that will prevent the pressure of the grout from deforming the frame mem-
bers. Grout shall be mixed to provide a 4″ (102mm) maximum slump consistency, hand
troweled into place. Grout mixed to a thin “pumpable” consistency shall not be used.
19
C. Doors shall be installed and fastened to maintain alignment with frames to achieve maxi-
mum operational effectiveness and appearance. Doors shall be adjusted to maintain
perimeter clearances as specified in Section 2.1.8. Shimming shall be performed by the
installer as needed to assure the proper clearances are achieved.
D. Installation of hardware items shall be in accordance with the hardware manufacturer’s
recommendations and templates. ANSI/SDI A250.6, Recommended Practice for Hardware
Reinforcing on Standard Steel Doors and Frames shall be consulted for other pertinent
information.
20
MEMBERS OF THE
Ceco Door
Milan, TN 38358
Curries
www.deansteel.com
Test Procedures
(909) 770-5700
HOLLOW METAL XPRESS
623-936-7000
www.meskerdoor.com
Corbin, KY 40701
155 Republic Drive
www.secmet.com
9017 Blue Ash Road
(513) 745-6400

440.899.0010 • FAX 440.892.1404
12/4/2014
www.steeldoor.org
ANSI/SDI A250.10-2011

Prime Painted Steel Surfaces
ANSI/SDI A250.10-2011
SPONSOR
Approved November 21, 2011
ANSI/SDI ®
A250.10-2011
Test Procedure and Acceptance Criteria for

Secretariat
Approved November 21, 2011


that all views and objections be considered, and that a concerted effort be
made toward their resolution.
The use of American National Standards is completely voluntary; their
existence does not in any respect preclude anyone, whether they have ap-
proved the standards or not, from manufacturing, marketing, purchasing, or
using products, processes, or procedures not conforming to the standards.
withdrawn at any time. The procedures of the American National Standards
Institute require that action be taken periodically to reaffirm, revise, or
withdraw this standard. Purchasers of American National Standards may
receive current information on all standards by calling or writing the Ameri-
can National Standards Institute.
Published by



ANSI/SDI A250.10-2011
Contents
Page
Foreword.. ............................................................................................ ii
1 Scope............................................................................................1
2 Material. . ........................................................................................1
3 Testing...........................................................................................1
3.1 Salt Spray Test.........................................................................1
3.2 Condensation Testing (Humidity). . .............................................1
3.3 Impact Test. . .............................................................................1
3.4 Film Adhesion Test.. ..................................................................2
4 Acceptance Criteria........................................................................2
4.1 Salt Spray Resistance.. .............................................................2
4.2 Condensation Resistance.. ........................................................2
4.3 Impact Test. . .............................................................................2
4.4 Film Adhesion. . .........................................................................2
5 Report. . ..........................................................................................2
6 General..........................................................................................2
6.1 Testing Laboratory....................................................................2
6.2 Certification..............................................................................2
Tables
1 Rust grades...................................................................................3
2 Classification of adhesive test results.............................................6
Figures
1 Visual reference for percentage of rust...........................................3
2 Blister size #2................................................................................4
3 Blister size #4................................................................................4
4 Blister size #6................................................................................5
5 Blister size #8................................................................................5
i
The original standard was issued on July 28, 1980 and was revised in 1990
and 1998, and the 1998 edition was reaffirmed in 2004. The current edi-
tion is a revision of the 1998 document with the contents being updated to
reflect changes and advances that have take place in the steel door and
frame industry.
Suggestions for improvement gained in the use of this standard are wel-
come and should be sent to the Steel Door Institute, 30200 Detroit Road,
Cleveland, OH 44145-1967.
FM Approvals
Therma-Tru
Wind Science & Engineering Research Center
ii
and had the following personnel at the time of approval:

Architectural Testing..................................................................... Dan Johnson
Builders Hardware Manufacturers Association............................ Michael Tierney
Curries Company......................................................................... Dave Dedic
Deansteel.................................................................................... Claus Heide
Door and Hardware Institute........................................................ Keith Pardoe
Door Components....................................................................... Tom Popow
MPI.............................................................................................. Tom Stone
Security Metal Products............................................................... Terry Simpson
Ingersoll Rand............................................................................. Kurt Roeper
Underwriters Laboratories Inc...................................................... Matthew Schumann
Vetrotech / Saint Gobain.............................................................. Christian Mueller
Wind Science & Engineering Research Center........................... Larry Tanner
iii

1 Scope 3 Testing
These methods prescribe the procedures to be 3.1 Salt spray test
followed in the selection of material, chemical
a) Apparatus — The apparatus used for salt
preparation, painting, testing, and evaluation
spray testing shall be of such design as to
of prime painted steel surfaces for steel doors
conform to ASTM B117-09, Standard Practice
and frames.
for Operating Salt Spray (Fog) Apparatus.
2 Material b) Test performance — Salt spray testing shall
2.1 The test specimen shall be the exact type be conducted as specified in ASTM B117-09,
and gauge of steel used in the manufacturing Standard Practice for Operating Salt Spray
of the product. It shall be 4" x 10" with a 1/4" (Fog) Apparatus for a test period of 120 con-
hole at the center of the 4" width, 1/2" in from tinuous hours. The test specimen(s) shall be
the end. When a specimen greater than 10" scribed with an "X" per ASTM D1654-92(2000)
in length is used for the coating process, the Standard Test Method for Evaluation of Painted
bottom 10" of the specimen shall be used for or Coated Specimens Subjected to Corrosive
all subsequent testing. Environments, sections 4.1 and 5.1.
Permanent identification marks shall be added 3.2 Condensation testing (humidity)

to the specimen as required for control pur- a) Apparatus — The apparatus used for con-
poses. densation (humidity) testing shall be of such
2.2 The specimen(s) shall be hung using a design as to conform to ASTM D4585-99, Stan-
method representative of that used in produc- dard Practice for Testing Water Resistance of
tion. Coatings Using Controlled Condensation.
2.3 The specimen(s) shall be cleaned, pre- b) Test performance — Condensation (humid-
treated and painted in accordance with the ity) testing shall be conducted as specified in
manufacturer’s normal production method and ASTM D4585-99, Standard Practice for Testing
procedure. All coating weights used on test Water Resistance of Coatings Using Controlled
specimens shall be documented and represen- Condensation, for a test period of 240 con-
tative of the individual manufacturer’s normal tinuous hours. Exposure temperatures shall be
production material. maintained at a minimum of 100° Fahrenheit.
Actual test temperature shall be noted in the
2.4 At the end of the paint cycle, the specimen(s)
report.
shall be removed from the paint system with
careful handling. The painted surface of the 3.3 Impact test
specimen shall not be handled or come in
The paint shall be tested per ASTM D2794-93
contact with other objects to prevent disruption
(2010)e1 Standard Test Method for Resistance
of the painted surface.
of Organic Coatings to the Effects of Rapid
2.5 All specimens shall be aged a minimum of Deformation (Impact), with 20 inch pounds of
72 hours prior to testing. direct impact using a Gardner Impact Tester with
1
ANSI/SDI A250.10-2011
1/2" diameter ball or punch at room temperature 4.4 Film adhesion

of 70° – 75° Fahrenheit. After impact is made,
There shall be no adhesion loss less than a
apply 3/4" wide #600 Scotch cellophane tape grade 3B as defined in ASTM D3359-09e2. This
firmly to the impact area and pull off sharply. grade represents a film removal of between 5
3.4 Film adhesion test and 15%. Table 2 illustrates the various clas-
sifications for adhesion loss.
The coating film adhesion shall be tested in
accordance with method “B” of ASTM D3359- 5 Report
09e2, Standard Test Methods for Measuring
5.1 The report shall cover the date the test was
Adhesion by Tape Test. A total of (11) parallel
performed and the issue date of the report.
cuts are made with a sharp instrument, 1 mm
apart in both a vertical and horizontal direction 5.2 Identification of the specimen tested, source
forming a grid. One inch wide pressure-sensitive of supply, manufacturer, model or series num-
tape is then firmly applied to the scribed surface ber, or both, and any other pertinent information.
and rapidly removed. 5.3 A detailed description of the specimen or
specimens tested shall include the type of
4 Acceptance criteria prime paint, the method of paint application,
4.1 Salt spray resistance the procedure used to cure it, and the dry film
thickness.
The paint film on the unscored surface of the
test specimen shall have a rust grade of no less 5.4 A statement that the test or tests were
conducted in accordance with the methods
than 6 as defined in ASTM D610-01, Standard
and procedures as specified herein. If devia-
Test Method for Evaluating Degree of Rusting
tions from these methods and procedures were
on Painted Steel Surfaces. Table 1 shall be
made, they shall be described in the report.
used to evaluate the rust grades. The paint
film at the scored line shall not be undercut 5.5 When the test is made to check the confor-
by rust more than 1/8" each side, when tested mance of the unit specimen to test requirements
in accordance with paragraph 3.1. of a particular specification, the identification
or description of the specification shall be in-
4.2 Condensation resistance cluded in the report.
The paint film may have any quantity of #8
blisters but, shall have no more than a few #6
6 General
blisters as illustrated in ASTM D714-02(2009), 6.1 Testing laboratory
Standard Test Method for Evaluating Degree of
All tests shall be conducted and/or certified by
Blistering of Paints, when tested in accordance
a nationally recognized, independent testing
with paragraph 3.2. Visual representations of laboratory accredited in accordance with ISO
the various degrees of blistering are shown in 17025 for the test methods referenced in the
Figures 2 through 5. standard.
4.3 Impact test 6.2 Certification
No paint film removal shall occur other than Reference may be made to this specification.
at an area 1/8" in diameter at the center of the When reference is made, the following statement
impact area, when tested in accordance with shall be used: Prime finish has been tested in
paragraph 3.3. conformance with ANSI Standard A250.10-1998.
2
ANSI/SDI A250.10-2011
Table 1 – Rust grades
Rust Grade Maximum % of rusted area

10 00.01
9 00.03
8 00.10
7 00.30
6 01.00
5 03.00
4 10.00
3 16.67
2 33.33
1 50.00
0 100.00
Figure 1 – Visual reference for percentage of rust
3
4
Visual examples illustrating degrees of blistering
ANSI/SDI A250.10-2011
FEW MEDIUM MEDIUM DENSE DENSE

Figure 2 – Blister size #2

Visual examples illustrating degrees of blistering


5
ANSI/SDI A250.10-2011
ANSI/SDI A250.10-2011
Table 2 – Classification of adhesive test results
Surface of cross-cut areas from

Classification which listing has occurred. (Ex- Rate of adhesion
ample for six parallel cuts.)
The edges of the cuts are

completely smooth; none of
5B None
the squares or the lattice are
detached.
Small flakes of coating are

detached at intersections; less
4B
than 5% of the area is af-
fected.
Small flakes of coating are

detached along edges and at
3B intersections of cuts. The area
affected is 5 to 15% of the
lattice.
The coating has flaked along

the edges and at parts of the
2B
squares. The affected area is
15 to 35% of the lattice.
The coating has flaked along

the edges of cuts in large rib-
1B bons and entire squares have
detached. The area affected is
35 to 65% of the lattice.
0B Flaking and detachment in excess of 65%.
6
MEMBERS OF THE
Ceco Door
Milan, TN 38358
Curries
www.deansteel.com
Test Procedures
(909) 770-5700
HOLLOW METAL XPRESS
623-936-7000
www.meskerdoor.com
Corbin, KY 40701
155 Republic Drive
www.secmet.com
9017 Blue Ash Road
(513) 745-6400

440.899.0010 • FAX 440.892.1404
12/4/2014
www.steeldoor.org
ANSI/SDI A250.11-2012
Recommended
Erection Instructions for Steel Frames
ANSI/SDI A250.11-2012
:765:69
:[LLS+VVY0UZ[P[\[L
(WWYV]LK1HU\HY`
ANSI/SDI ®
A250.11-2012

Recommended
Erection Instructions
for Steel Frames
Secretariat


Published by



ANSI/SDI A250.11-2012
Contents
Page
1 Scope ............................................................................................1
2 Storage and Preliminary Assembly .................................................1
3 Plumbing and bracing frames ........................................................2
4 Accessories ...................................................................................3
5 New masonry construction ............................................................4
6 Existing masonry construction ......................................................4
7 Steel stud wall construction, studs erected with frame ..................5
8 Double egress frames in steel stud wall construction ....................6
9 Wood stud construction (studs erected with frame) .......................7
10 Wood/steel stud construction (studs erected before frame) .........9
11 Slip-on drywall ...........................................................................10
12 Butted or Existing Steel or Wood Stud Wall Construction .......... 11
Figures
1 Examples of the accuracy to be maintained while setting frames ..2
2 Spreader ........................................................................................3
3 Plumbing the frame .......................................................................3
4 Bracing the frame ..........................................................................3
5 Rubber silencers ............................................................................4
6 Extended base anchor ...................................................................4
7 New masonry construction ............................................................4
8 Masonry anchors ...........................................................................4
9 Existing masonry construction .......................................................5
10 Rough Opening ............................................................................5
11 Existing masonry or concrete wall anchors ..................................5
12 Steel stud wall construction .........................................................5
13 Channel type steel stud ...............................................................6
14 Erect frame ..................................................................................6
15 Anchor jambs ..............................................................................7
16 Anchor header .............................................................................7
17 Erect frame ..................................................................................7
18 Wood stud wall construction ........................................................8
19 Weld in strap anchors wood/steel studs ......................................8
i
Page
20 Snap or weld in anchors wood/steel studs ..................................8

21 Z Type weld in anchors steel studs ..............................................8
22 Rough opening shown in wood stud. ...........................................9
23 Wood stud wall construction ........................................................9
24 Weld in strap anchors wood/steel studs ......................................9
25 Snap or weld in anchors wood/steel studs ................................ 10
26 Z Type weld in anchors steel studs ............................................10
27 Rough opening ..........................................................................10
28 Align corner gussets ..................................................................11
29 Level and square frame .............................................................11
30 Anchor adjusting screw .............................................................11
31 Fasten base anchors to wall stud .............................................. 11
32 Hole plug mount ........................................................................12
33 Countersink mount ....................................................................13
Annexes
A Manufacturing Tolerances
for Standard Steel Doors and Frames .........................................14
B Installation Exceptions ................................................................20
ii
welcome. They should be sent to the Steel Door Institute, 30200 Detroit
Road, Cleveland, OH 44145-1967.
The organizations that have approved this standard are part of the ANSI
A250 Accredited Standards Committee, formed February 8, 1991, and are
as follows:
FM Approvals
Hollow Metal Manufacturers Association/Division of NAAMM
Wind Science & Engineering Research Center
Therma-Tru
The Technical Committee of the Steel Door Institute, which developed this
standard, had the following personnel at the time of approval:
Claus D. Heide, Chairman

Mike Torres, 1 st Vice Chairman
Tom R. Janicak, 2 nd Vice Chairman
J. Jeffery Wherry, Manager
Ceco Door Products................................................................... Tom R. Janicak
Curries Company ....................................................................... Dave Dedic
Deansteel Manufacturing Co. ..................................................... Claus D. Heide
Door Components Inc. ............................................................... Tom Popow
Mesker Door Company .............................................................. Mike Torres
Metal Products Inc. .................................................................... Tom Stone
Pioneer Industries....................................................................... Kamal Sheikh
Republic .................................................................................... Steven Hugueley
Security Metal Products ............................................................ Terry Simpson
Steelcraft .................................................................................... Karen Bishop
iii
AMERICAN NATIONAL STANDARD ANSI A250.11-2012
Recommended Erection Instructions

for Steel Frames
1 Scope HMMA 841-07, Tolerances and Clearances for

Commercial Hollow Metal Doors and Frames
1.1 Recommended methods for the installation
of steel frames for swinging doors in a variety of 1.2.1 Further information on wall construction,
wall conditions, commonly used in commercial anchoring, details, manufacturing tolerances
buildings, are covered within this standard. The or installation may be found in the following:
installation of transom/sidelight (or panel) type
SDI 110-2009, Standard Steel Doors and
frames and single or multiple borrowed lights
Frames for Modular Masonry Construction
are not covered in this standard.
SDI 111-2009, Recommended Standard Details
1.1.1 It is not the intention of this document
for Steel Doors, Frames, Accessories and Re-
to obstruct the development of alternative in-
lated Components
stallation methods, nor is it intended to restrict
frame installation solely to the wall types noted SDI 122-2007, Installation and Troubleshooting
herein. Guide for Standard Steel Doors and Frames
1.1.2 Although this document is commonly SDI 127D-2006, Electric Strikes in Stud
referenced for severe windstorm installations, Walls
critical performance requirements (such as
1.3 Metrication
type, quantity, and location of anchors) shall
be as indicated in the manufacturer’s published 1.3.1 Standard dimensions used in this docu-
Approvals or Listings. ment are in inch-pound units. Metric values,
where applicable, are included in parenthesis
1.2 Reference documents
for reference only. These are “soft conversion”
SDI 127E-2006, Prime Painted Materials approximates.
Alert
2 Storage and Preliminary Assembly
SDI 127F-2010, Butted Frames Rough Open-
(see SDI 127E, and ANSI/SDI A250.8)
ing Sizes
2.1 All frames, including knocked-down, shall
SDI 127J-2010, Back-Coating of Frames
be stored under cover.
SDI 117-2009 Manufacturing Tolerances for
2.1.1 Knocked-down frames shall be placed
flat on at least 4˝ (102 mm) wood sills to prevent
NFPA 80-2010, Standard for Fire Doors and the frames from resting on the ground.
Other Opening Protectives (National Fire
2.1.2 Assembled frames shall be stored verti-
Protection Association, 1 Batterymarch Park,
cally. The units shall be placed on at least 4˝
Quincy, MA 02269; www.nfpa.org)
(102 mm) high wood sills or in a manner that
UL10C-2009 Standard for Safety Positive Pres- will prevent rust or damage.
sure Fire Tests of Door Assemblies
2.1.3 The use of non-vented plastic or canvas
ANSI/SDI A250.8-2003(R2008) Recommended shelters that can create a humidity chamber
Specifications for Standard Doors and Frames shall be avoided.
HMMA 840-07, Installation and Storage of Hol- 2.1.4 Refer to project specifications for re-
low Metal Doors and Frames quired cleanup and touchup work.
1
ANSI A250.11-2012
2.2 Back-Coating (see SDI 127J for further 2.4 Assembly of frame/anchor provisions
information)
2.4.1 Follow manufacturers’ recommended
2.2.1 When temperature conditions necessi- procedure for assembly of frame and quantity
tate the use of anti-freezing agents in plaster or and spacing of anchors. If not indicated, install
mortar, the inside of the frame shall be coated anchors at hinge levels and directly opposite
at the jobsite with a corrosion resistant coating at strike jamb.
by the contractor responsible for installation. 2.5 Verification
2.3 Grouting of frames (see ANSI/SDI 2.5.1 Prior to installation, jobsite personnel
A250.8 for further information) shall ensure correct swing, size and labeling.
2.3.1 Where grouting is required in masonry 2.6 Installation tolerances
installations, frames shall be braced or fastened 2.6.1 While this document is mainly concerned
in such a way that will prevent the pressure of with tolerances relating to the manufacturing
the grout from deforming the frame members. process, openings will not function properly
if the frame is not installed within recognized
2.3.2 Grout shall be mixed to provide a 4˝ (102
tolerances.
mm) maximum slump consistency, and be hand
troweled into place. Grout mixed to a thinner Figure 1 shows examples of the accuracy to
“pumpable” consistency shall not be used. be maintained while setting frames.
2.3.3 Standard mortar protection in frames is 3 Plumbing and bracing frames

not intended for thin consistency grout. Steel
frames, including fire rated frames, do not re- 3.1 Wood Spreaders (see Figure 2)
quire grouting. Grouting is not recommended The Contractor(s) responsible for installation
for frames installed in drywall. shall have available a sufficient supply of wood
1⁄16˝ (1.58 mm)
Strike 1⁄16˝
Hinge Jamb (1.58 mm)
Jamb
Hinge or Hinge or
1⁄16˝ (1.58 mm)
Strike
Hinge Bottom Bottom
Jamb 1⁄16˝
Jamb (1.58 mm)
Maximum 1⁄16˝ allowable tolerance on total opening.

1b – Plumbness
1a – Squareness
1⁄16˝ (1.58 mm)
1⁄16˝ (1.58 mm)
1c – Alignment 1d – Twist
Figure 1 – Examples of the accuracy to be maintained while setting frames

2
ANSI A250.11-2012
spreaders for bracing frames. Spreader bars 3.3 Bracing the frame (see Figure 4)
for shipping purposes shall not be used as
3.3.1 Frame bracing shall be as shown or
installation spreaders.
shore to a structure above.
3.1.1 Wood spreaders shall be square and
3.3.2 Bracing shall be perpendicular to the
fabricated from lumber no less than 1˝ (25.4
intended wall.
mm) thick. Correct length is the door opening
width between the jambs at the header (i.e.,
Single Door 3´-0˝ = 36˝= 915 mm). Length
tolerance is +1⁄16˝, -0˝ (+1.6 mm, –0). Cut clear-
ance notches for frame stops. Spreader shall
be nearly as wide as frame jamb depth for
proper installation.
Frame
Depth
Door opening at header
Figure 2 – Spreader
3.2 Equipment for plumbing the frame

(see Figure 3)
3.2.1 The contractor should be equipped with
a carpenter level, square and wood spreaders.
Figure 4 – Bracing the frame
3.2.2 Where welded frames are provided with
spreader bars, they shall be removed with a 3.4 Positioning the frame
suitable saw or chisel and filed flush before 3.4.1 Set the frame in the desired location and
setting frames. level the header. Square jambs to header. Shim
under jambs if necessary. With frame properly
aligned, insert wood spreaders at bottom and
mid-height and fasten jambs to floor through
floor anchors.
Plumb
3.4.2 Plumb and square jambs. Install verti-

cal brace to support header for openings over
Level
4´-0˝ (1219 mm) wide.
Square
4 Accessories
4.1 Install rubber silencers (see Figure 5)
4.1.1 Cut the point from a #6d box or finish-
Section A–A ing nail. Insert nail in hole to elongate rubber
silencers.
A A
Moisten the end and insert rubber silencers in
predrilled holes on frame stop, remove nail. The
Wood spreader thickness of the silencer shall permit latching
between jambs of door with 1⁄16˝ to 3⁄32˝ (1.6 to 2.4 mm) clear-
ance between face of door and stop of frame.
4.1.2 Install rubber silencers before frame
Figure 3 – Plumbing the frame erection to avoid grout filling rubber silencer
3
ANSI A250.11-2012
5.2 Erect, brace, square and plumb frame.

5.2.1 Fasten frame to floor through base
anchors.
5.3 Set second spreader at the mid-height of
the door opening to maintain the door open-
ing size.
5.4 Install anchors (see Figure 8). Grout frame
in the area of the anchors as block courses
Figure 5 – Rubber silencers are laid up.
holes. In some cases rubber silencers are fac-
tory installed.
4.2 Extended base anchor (see Figure 6)
4.2.1 Extended base anchors are supplied
upon request only. (If required for tool attach-
ment.)
5 New masonry construction (see

Figure 7)
5.1 Assemble frame per manufacturer’s in-
structions.
Figure 8 – Masonry anchors
5.4.1 Frames may also be supplied with an-

chors welded in place.
5.5 Continually check plumb and square as
wall progresses.
6 Existing masonry construction

(see Figure 9, Figure 10, and SDI 127F)
6.1 Rough openings for existing wall, structural
steel framing, or retrofit installations utilizing a
Figure 6 – Extended base anchor butted to wall application shall be no less than
3⁄16˝ (4.8 mm) larger the frame on all three sides.
6.1.1 The installer is responsible for any shim-
ming or aligning required. Gaps are normally
90° 90° sealed as part of the installation or caulking/
painting process.
Wood spreader 6.1.2 Refer to Architectural specifications for
between jambs the appropriate sealant material to be used at
fire or smoke control doors.
structions.
6.3 Install snap-in anchors (see Figure 11)
and tap with a hammer to align with pierced
holes in jambs.
Figure 7 – New masonry construction
4
ANSI A250.11-2012
6.4 Slide frame into wall opening; install wood

spreaders.
90° 90°
6.5 Where possible, one jamb should be butted
tightly to the wall.
6.6 Use tapered shims between anchors and
Wood spreader wall and spreaders to maintain squareness
between jambs
and alignment of frame, and to maintain door
opening sizes.
6.6.1 Drill appropriate size hole (per fastener
manufacturer’s instructions) for one-piece an-
chor bolts. Leave holes “rough” for added grip.
6.6.2 Backer rod or caulking shall be used
where gaps occur between frame and wall.
6.7 Insert anchor bolts and tighten securely,
checking for frame alignment periodically.
6.8 Install plugs to cover bolt heads (if so
Figure 9 – Existing masonry construction
equipped).
7 Steel stud wall construction, studs

erected with frame (see Figure 12)
structions.
7.2 Install snap-in anchors. Position anchors
Rough opening height + $,1"
in frame through the throat and tap in with a

hammer.
Rough opening width chors welded in place.
+ "
Ceiling runner Header channel
Jamb
studs
90° 90°
Figure 10 – Rough Opening
Wood spreader
between jambs
Hole plug
Figure 11 – Existing masonry

or concrete wall anchors Figure 12 – Steel stud wall construction
5
ANSI A250.11-2012
7.3 Erect, brace, square and plumb frame as 8 Double egress frames in steel stud
shown. wall construction
7.4 Install wood spreaders. 8.1 Generally, the installation of double egress
frames in steel stud walls follows the same
7.5 Attach jambs to floor through floor anchor
procedure as Section 7.
or floor extension.
8.1.1 If frames are supplied knocked down,
7.6 Install jamb studs to floor, header chan-
assemble per manufacturer’s instructions.
nels, and ceiling runners butted tightly against
frame anchors and properly positioned in frame 8.1.2 Install anchors (if not supplied welded
throat for wallboard. to frame) per manufacturer’s instructions.
7.6.1 Nesting or overlapping stud joints or 8.2 Erect, brace, square and plumb frame as
other wall construction practices that will in- shown (see Figure 14).
crease the overall wall thickness beyond the
intended finished thickness are to be avoided.
Ceiling stud
7.7 Attach jamb studs to anchors with screws
or weld.
7.7.1 If using screws, drill from the back side Angle braces
of the stud, through both the stud and anchor,
then attach with (2) screws per anchor loca-
tion (see Figure 13). Screws shall be #6 x ⅜˝
minimum steel sheet metal or self tapping type.
Frame
Wood spreader
Channel type
between jambs
jamb studs
Figure 14 – Erect frame
8.2.1 Stand frame up in desired location. An-

chor one jamb to floor and set wood spreader
on floor from anchored jamb to loose jamb.
Figure 13 – Channel type steel stud 8.2.2 Install a vertical wood brace at center
of frame.
7.7.2 When attaching header stud to jamb
8.2.3 Position and anchor second jamb to
studs, be sure the stud is above frame header.
floor. Plumb, level and square frame, then install
This will assure ample room for attaching plaster
wood spreaders at mid-height.
lath or drywall and will not interfere with instal-
lation of hardware attached to frame header.
7.7.3 At wrap-around installations in fire rated
walls, drywall shall extend at least ½˝ (12.7
mm) into frame throat. See Section 12 for frame
installations in butted or existing stud walls.
6
ANSI A250.11-2012
8.5 Anchor header (see Figure 16)

Header anchor requirements will vary. The
manufacturer’s installation requirements should
90° 90° be followed.
8.6 At wrap-around installations in fire rated
walls, drywall shall extend at least ½˝ (12.7
mm) into frame throat. See Section 12 for frame
installations in butted or existing stud walls.
Wood
spreader 9 Wood stud construction (studs
between erected with frame)
jambs
structions.
Figure 15 – Anchor jambs 9.2 Install snap-in anchors. Position anchors
8.3 Anchor jambs (see Figure 15) hammer.
8.3.1 Install jamb studs to floor, header chan-

nels, and ceiling runners butted tightly against
frame anchors and properly positioned in frame
throat for wallboard.
Angle
8.3.2 Nesting or overlapping stud joints or braces
other wall construction practices that will in-
8.4 Attach jamb studs to anchors with screws
or weld.
8.4.1 If using screws, drill from the back side
of the stud, through both the stud and anchor,
then attach with (2) screws per anchor loca-
tion (see figure 15). Screws shall be #6 x ⅜˝ Wood spreader
between jambs
minimum steel sheet metal or self tapping type.
Figure 17 – Erect frame

½" long (max.)
screw 9.3 Square, brace and plumb frame as shown
(see Figure 17).
9.4 Install wood spreaders (see Figure 18).
9.5 Attach jambs to floor through floor anchor
or floor extension.
Alt. profile
9.6 Install jamb studs (jack stud and king
Wood stud) butted tightly against anchors and prop-
spreader erly positioned in frame throat for wallboard
between Second stud at
jambs head and jambs (see Figure 18).
9.6.1 Attach header stud(s) or header assem-
Figure 16 – Anchor header bly between jamb studs making sure they are
7
ANSI A250.11-2012
Ceiling runner Header
Jamb
studs
90° 90°
Double
header and
jamb studs
required
Wood
spreader
Floor between
runner jambs
Figure 20 – Snap or weld in anchors wood/

steel studs
Figure 18 – Wood stud wall construction
9.8 Square and nail top anchor to stud on
ONE JAMB ONLY. Check plumb and square
above the frame head. This will assure ample and continue to nail balance of anchors to
room for attaching plaster lath or drywall and stud. Repeat for opposite jamb. For steel studs
will not interfere with installation of hardware install screws from back of stud into Z anchor
attached to frame head (see Figure 18). (see Figure 21).
9.7 Bend anchor straps around stud leaving 9.8.1 At wrap-around installations in fire rated
sufficient clearance between frame return and walls, drywall shall extend at least ½˝ (12.7
stud for inserting finished wall material (see mm) into frame throat. See Section 12 for frame
Figure 19 and Figure 20). installations in butted or existing stud walls.
Figure 19 – Weld in strap anchors wood/steel

studs
9.7.1 If there is insufficient room for wall finish,
notch jamb studs no more than 1⁄16˝ (1.6 mm)
deep for anchor straps.
Figure 21 – Z Type weld in anchors steel studs
8
ANSI A250.11-2012
10 Wood/steel stud construction 10.1.1 Assure that rough openings are no less
(studs erected before frame) than those required in SDI 127F.
10.1 Build rough opening (see Figure 22) 10.1.2 It is recommended that double studs
according to dimensions and clearances in be used at jambs and headers.
manufacturer’s installation instructions.
10.2 Assemble frame per manufacturer’s
instructions.
10.3 Install snap-in anchors. Position anchors
hammer.
10.3.1 Frames may also be supplied with
anchors welded in place.
10.3.2 If base anchors cannot be used add
one anchor per jamb at bottom.
10.3.3 Install fire rated frames with the an-
Rough
chor quantity and spacing as per the individual
opening manufacturer’s listings and instructions.
demensions
10.4 Slide frame into wall opening.
10.4.1 Install wood spreaders at bottom and
mid-height. Square and level frame. Shim jambs
if necessary (see Figure 23).
10.5 Bend anchor straps around stud leaving
sufficient clearance between frame return and
stud for inserting finished wall material (see
Figure 24 and Figure 25).
Figure 22 – Rough opening shown in wood
stud.
90° 90°
Figure 24 – Weld in strap anchors wood/steel

Wood studs
spreader
between
jambs
Figure 23 – Wood stud wall construction

9
ANSI A250.11-2012
10.6.1 NOTE: At wrap-around installations in

fire rated walls, drywall shall extend at least
½˝ (12.7 mm) into frame throat. See Section
12 for frame installations in butted or existing
stud walls.
11 Slip-on drywall
11.1 Prepare rough opening (see Figure 27)
per frame manufacturer’s recommendations.
11.1.1 Nesting or overlapping stud joints or
other wall construction practices that will in-
11.2 Install base anchors if not factory welded
to jambs or if frame faces are not prepared for
base anchor screws.
Figure 25 – Snap or weld in anchors wood/
steel studs
10.6 Square and nail top anchor to stud on

ONE JAMB ONLY. Check plumb and square
and continue to nail balance of anchors to
stud. Repeat for opposite jamb. For steel studs
install screws from back of stud into Z anchor
Rough opening height

(see Figure 26
Rough opening width
Figure 27 – Rough opening
Figure 26 – Z Type weld in anchors steel studs
10
ANSI A250.11-2012
11.3 Install jambs and header onto wall per

manufacturer’s instructions, taking care to align
corner gussets (if so equipped). See Figure 28.
Anchor adjusting screw

(Typical both sides)
Figure 30 – Anchor adjusting screw
11.6 Re-check level and square. Adjust using

anchor screws as needed.
11.7 Fasten base anchors to wall stud (see
Figure 31) or fasten to wall studs through pre-
pared holes in face of jambs at bottom.
Figure 28 – Align corner gussets
11.4 Level and square frame (see Figure 29)

11.4.1 Install wood spreaders.
11.5 Turn adjusting screws hand tight (DO NOT
USE SCREW GUN) until compression anchor
contacts jamb studs. See Figure 30.
Level
and
square
Figure 31 – Fasten
base anchors to wall stud
12 Butted or Existing Steel or Wood

Stud Wall Construction
12.1 Historically, frames installed in fire rated
stud walls required frames to wrap around
the wall and drywall must extend at least ½˝
(12.7 mm) into frame throat. Fire testing has
Figure 29 – Level and square frame
11
ANSI A250.11-2012
confirmed that fire door frames will perform 12.2 Assemble knock down frames per manu-
satisfactorily to the acceptance criteria of UL facturer’s instructions.
10C under positive pressure when butted to
new or existing stud and drywall construction 12.3 Anchors are typically welded to frames
(see Figure 32 and Figure 33). and will either be a sleeve aligned with a coun-
tersunk hole or a plate between returns with
12.1.1 This installation has been incorpo-
rated into NFPA 80 as Figure A.6.3.1.3(a) and an access hole and plug.
A.6.3.1.3(b). 12.4 Assure that rough opening or opening
12.1.2 Applicable Building Codes and indi- between walls is plumb, square, and properly
vidual manufacturers’ product listings shall be sized to fit overall frame dimensions and expan-
consulted when these butted frames are used sion capability of intumescent caulk or sealant.
in fire rated walls. (See SDI 127F for further information).
12.1.3 This installation process DOES NOT 12.5 Using a “stud finder” or similar tool, as-
apply to Slip-on Drywall frames in Section 11.
sure that studs will align with frame mounting
12.1.4 Listed fill, void or cavity material shall screws.
be used at the junction of frame faces and
returns with the drywall surface. The bead 12.6 Slide frame into wall opening; install
of fill, void or cavity material shall be no wider wood spreaders at the floor and mid-height
than ½˝ (12.7 mm). of opening.
Intumescent caulk
both sides
25 Gauge
steel stud
Access hole and
snap-in plug
Fire rated
wallboard ¼" x 2" Sheet metal screws
(hex head), 6" max. from
ends and 24" O.C. max.
(provided by installer)
2" Wide x 12 ga. strap. length

equals jamb width minus ¼",
weld to returns
Figure 32 – Hole plug mount

12
ANSI A250.11-2012
12.7 Use tapered shims between anchors for frame alignment periodically. (Frame profiles
and wall and spreaders to maintain squareness shown are for general details only. Anchors and
and alignment of frame and to maintain door profiles may vary).
opening. Make sure that shims will not inter-
rupt the sealant. 12.9 Insert plugs to cover access holes if so
equipped.
12.8 Insert ¼˝ (6.4 mm) sheet metal screws
of suitable length to engage studs through 12.10 Install Listed intumescent caulk or seal-
countersink or access hole in frame (see Figure ant around perimeter of frame, making sure to
32 and Figure 33) and tighten securely. Check cover any gaps caused by irregularities in walls.
Fire rated
wallboard, Intumescent caulk,
both sides both sides
¾" Dia. conduit

spacer
Jamb punched and

25 Gauge dimpled for screws.
steel studs ¼" S.M.S., 6" max.
from ends, 24" O.C.
max. (Provided by
installer)
2" Wide x 12 ga. strap. length

equals jamb width minus ¼",
weld to returns
Figure 33 – Countersink mount
13
ANSI A250.11-2012
Annex A
(informative)
Manufacturing Tolerances for Standard Steel Doors and Frames
A1 Introduction ASTM A653-10 Standard Specification for Steel

Sheet, Zinc-Coated (Galva nized) or Zinc-Iron
It is the intent of this publication to inform us-
Alloy-Coated (Galvannealed) by the Hot-Dip
ers of standard steel doors and frames with
Process
definitive information regarding manufacturing
tolerances. It is also intended to inform the ASTM A924-10 Standard Specification for
installation contractor(s) of the tolerances to General Requirements for Steel Sheet, Metallic-
be considered to assure proper operation of Coated by the Hot-Dip Process
the complete opening. It is intended for in-plant
NFPA 80-2010 Standard for Fire Doors and
inspections. It may be used for on-site inspec-
Other Opening Protectives, 2007 Edition (Na-
tions where there is no evidence of damage to
tional Fire Protection Association, 1 Battery-
material or improper installation.
march Park, Quincy, MA 02269; www.nfpa.org)
The information contained herein pertains to
SDI 122-07 Installation and Troubleshooting
doors and frames manufactured in accordance
Guide for Standard Steel Doors and Frames
with ANSI A250.8, Recommended Specifica-
tions for Standard Steel Doors and Frames. It
A3 Materials and Finishes
is not intended to have reference to special or
unusual door and frame conditions. A3.1 Steel Thickness:
Manufacturers no longer order sheet and coil
A2 Reference Documents: to a specific gage, but rather to a minimum
ANSI/SDI A250.8-2003 (R2008) SDI 100 Rec- decimal thickness. This thickness is the lowest
ommended Specifications for Standard Steel of the range for a specific gage. The steel sup-
Doors & Frames plier is therefore permitted to exceed, but not
be less than the specified decimal thickness.
ANSI/SDI A250.6-2003 (R2009) Recommended
These minimum values meet the stringent re-
Practice for Hardware Reinforcings on Standard
quirements of both Underwriters Laboratories
Inc. and ITS/Warnock Hersey. Examples of
ANSI/SDI A250.7-1997 (R2002) Nomenclature minimum allowable steel thickness:
for Standard Steel Doors & Steel Frames
ANSI/SDI A250.3-2007 Test Procedure & Ac-
ceptance Criteria for Factory Applied Finish Gage (MSG) Minimum
Coatings for Steel Doors & Frames 20 0.032˝
ANSI/SDI A250.10-1998 (R2004) Test Proce- 18 0.042˝
dure & Acceptance Criteria for Prime Painted 16 0.053˝
Steel Surfaces for Steel Doors & Frames
14 0.067˝
ANSI/BHMA A156.115-2006 Hardware Prepara- 12 0.093˝
tion in Steel Doors and Steel Frames
10 0.123˝
ANSI/BHMA A156.115-W-2006 Hardware 7 0.167˝
Preparation in Wood Doors with Wood or Steel
Gage (MSG) are for reference purposes only.
Frames
ASTM A568-09 Standard Specification for Steel,
Sheet, Carbon, Structural, and High-Strength,
Low-Alloy, Hot-Rolled and Cold-Rolled, General
Requirements for
14
ANSI A250.11-2012
A3.2 Steel Coatings A4.2 Frame Opening & Vertical Locations

Thickness of metallic coatings (generally zinc)
are defined by ASTM A924, Standard Specifica-
tion for General Requirements for Steel Sheet,
Metallic-Coated by the Hot-Dip Process and ±-˝
A653, Standard Specification for Steel Sheet, L Hinge
C
Zinc-Coated (Galva nized) or Zinc-Iron Alloy-
Coated (Galvannealed) by the Hot-Dip Process.
The two most commonly used are designations ±/˝
Opening
A40 and A60. Minimum requirements for these Height
designations are: +",1˝ –-˝
±/˝
A40= 0.40 oz/ft 2 total both sides. CL
Strike
A60= 0.60 oz/ft 2 total both sides.
For reference, 1 oz/ft 2 = 1.7 mils thickness.
±-˝
A3.3 Factory Applied Coatings:
Since factory applied coatings (primer, finish
paint, etc.) are subject to performance stan-
dards rather than thickness, the dry film thick-
ness is irrelevant. Such coatings must comply Opening Width
with performance criteria of: +",1˝ –-˝
ANSI/SDI A250.3 – Test Procedure and Ac-

ceptance Criteria for Factory Applied Finished Figure B – Opening Tolerances
Painted Steel Surfaces for Steel Doors and A4.3 Bow or Twist of Jambs or Header
Frames
Realizing that frames are somewhat “pliable”,
OR and require bracing and alignment during instal-
ANSI/SDI A250.10 – Test Procedure and Accep- lation, allowable deformation (bow, twist, etc.) of
tance Criteria for Prime Painted Steel Surfaces jambs or header of frame prior to installation
for Steel Doors and Frames. shall not result in a reduction of opening sizes
more than 1⁄16˝ beyond those shown in Figure
A4 Frame Tolerances B when measured at any point.
A4.1 Frame Cross Section Profile A4.4 Horizontal Alignment of Door Within
Rabbet
Permissible tolerances in frame profile surfaces
are as shown in Figure A. Hinge and strike backsets shall allow the hori-
zontal centerline of the door to be in line with
the horizontal centerline of the frame rabbet ±
⅓2˝ prior to installation. Figure C is an example
Face based on a 1 ¾˝ door in a 1 15⁄16˝ rabbet.
±-˝
Stop
±-˝
Rabbet
±-˝
Throat 1˝ or $-˝ ± -˝

Frame Opening
Depth ±$.-˝
±",1˝
Centerline of door
1 ˝ door
Figure A – Profile Tolerances

Figure C – Horizontal Alignment
15
ANSI A250.11-2012
4.5 Frames With Lights or Panels A5.2 Door Squareness

Opening sizes (width or height) for side or When measured diagonally (see Figure F) from
transom lights or panels and for borrowed light corner to corner along the same face, the mea-
frames shall be subject to a tolerance of ± 1⁄16˝ surements shall be within 1⁄16˝ of each other.
for each individual light or panel. These toler-
ances shall be non-accumulative so that the
overall frame opening sizes are not increased
by more than ⅛˝ (see Figure D).
± ˝
± ",1˝ ± ",1˝ ± ",1˝
± ",1˝
Figure F – Squareness
± ˝ A5.3 Door Perimeter Flatness
When a suitable straightedge is laid against the
door face at or within ¼˝ of the top, bottom,
± ",1˝ hinge edge, and lock edge on both faces any
deviation between the face and the straightedge
shall not allow a 0.0625˝ rod or block to pass
(see Figure G). Note: The straightedge shall be
allowed to “rest” naturally on the door surface,
not pulled down at one end to meet the door.
Figure D – Frames with Lights or Panels
A5 Door Tolerances
A5.1 Door Size, Thickness, and Vertical
Locations (see Figure E)
Straightedge
Door Width
±$1/˝
Door ",1˝ max
Thickness
±-˝ ±",1˝
CLHinge
",1˝ max
±/˝
Door
Height
±$1/˝
CLLock Straightedge
±/˝
Lock Figure G – Flatness

Height
±-˝ A5.4 Door Face Bow or Crown
When a suitable straightedge is laid diagonally
against the door face at least ½˝ from corners
Figure E – Doors any deviation between the face and the straight-
edge shall not allow a 0.125˝ rod or block to
pass (see Figure H). Note: The straightedge
16
ANSI A250.11-2012
shall be allowed to “rest” naturally on the door inserted between the fixture and the door face
surface, not pulled down at one end to meet at all four corners of the door. Any deviation
the door. between the face and the support blocks shall
not allow a 0.0625˝ rod or block to pass (see
Figure I). Note: The door shall be allowed to
“rest” naturally on the support blocks, not pulled
down at any corner to meet the blocks.
A5.6 Doors With Lights or Panels
Opening sizes (width or height) for lights or
panels cut into doors shall be subject to a toler-
ance of ± 1⁄16˝ for each individual light or panel.
A6 Hardware Preparations
A6.1 Vertical Locations
Straightedge
Tolerances for vertical locations are as noted
in Paragraphs A4.2 and A5.1.
⅛˝ max A6.2 Horizontal Alignment
Tolerances for horizontal alignment of door and
rabbet are as noted in Paragraphs 4.4.
Door
A6.3 Mortise Depth
Figure H – Door face bow or crown The depth of hardware items mortised into
edges of doors (such as hinges, strikes, lock
A5.5 Door Twist
fronts, flushbolts) shall be as defined on manu-
The door is laid onto a suitable, flat fixture or facturer’s templates and/or ANSI A156.115
surface that is free of any warp, bow, or twist. documents subject to an additional tolerance
Support blocks of identical heights shall be of ± ⅙4˝
Flat
Surface
Door Surface
",1˝ max.
Figure I – Door Twist

17
ANSI A250.11-2012
A6.3.1 Cutout Depth at Frame or Door Shims are usually thin strips of ¼˝ wide mate-
Faces rial approximately equal to the hinge height.
In order to allow for field adjustment, usually A7.1.1 Figure J shows how to relocate the
accomplished by shimming, hardware cutouts pivot point toward the jamb.
(such as hinges) that extend from door edges
A7.1.2 Figure K shows how to relocate the pivot
around to faces or from frame rabbet around to
point away from the jamb.
faces are allowed to exceed mortise depth by
1⁄16˝. See Paragraph A7 for examples of com- A7.2 Frame Installation Tolerances
mon hinge shimming procedures.
While this document is mainly concerned
A6.3.2 Depth For Recessed or Concealed with tolerances relating to the manufacturing
Hardware process, openings will not function properly
if the frame is not installed within recognized
The depth for hardware items recessed into
tolerances.
top or bottom of doors or edges of doors (such
as pocket pivots, floor closers, top pivots, Figures L, M, N, and O show examples of the
concealed closers or holders, etc) shall be as accuracy to be maintained while setting frames.
defined on manufacturer’s templates subject to
A7.3 Troubleshooting
an additional tolerance of +1⁄16˝, –0˝. Notches
in door faces shall have similar tolerances. Further information regarding corrective actions
for of door & frame openings may be found in
A7 Frame Installation And Door Ad- SDI-122.
justments
A7.1 Adjusting Pivot Point by Shimming
Providing extra depth along door or frame
faces allows for hinge knuckles to be offset,
thus changing the pivot point of the opening.
C
L Hinge CL Hinge
Barrel Hinge
Barrel Hinge Shim B
Jamb
Jamb Hinge Shim D Hinge
Reinf. Reinf.
Door Door Shim C

Shim A
“X”
“Y”
r 6TJOHTIJN"POMZ EPPSXJMMCFSFMPDBUFE r 6TJOH TIJN $ POMZ EPPS XJMM CF SFMPDBUFE JO
JOUIFEJSFDUJPOPGBSSPXi9u EJSFDUJPOPG"SSPXi:u
r 6TJOH TIJN # POMZ XJMM NPWF CPUI EPPS r 6TJOH%POMZ CPUIEPPSBOEDFOUFSMJOFPGIJOHF
BOEDFOUFSMJOFPGIJOHFCBSSFMJOEJSFDUJPO CBSSFMXJMMNPWFJOUIFEJSFDUJPOPG"SSPXi:u
PG"SSPXi9u
r 6TJOHCPUITIJNT$BOE%XJMMSFMPDBUFUIFEPPS
r 6TJOHCPUITIJNT"BOE#XJMMSFMPDBUFUIF JO EJSFDUJPO PG"SSPX i:u CZ B HSFBUFS BNPVOU
EPPSJOEJSFDUJPOPG"SSPXi9uCZBHSFBUFS UIBOCZVTJOHFJUIFS$PS%BMPOF5IFDFOUFSMJOF
BNPVOUUIBOCZVTJOHTIJNi#uBMPOF PGIJOHFCBSSFMXJMMCFSFMPDBUFEUIFTBNFBTCZ
VTJOHTIJN%BMPOF
Figure J – Hinge Bind Figure K – Hinge Bind

18
ANSI A250.11-2012
",1˝ (1.58 mm)
Strike
Hinge Jamb
Jamb
",1˝ (1.58 mm)
",1˝ (1.58 mm)
Strike
Hinge Jamb
Jamb
Maximum ",1˝ allowable tolerance on total opening.

Figure N – Alignment
Figure L – Squareness

",1˝
(1.58 mm)
Hinge or Hinge or
",1˝ (1.58 mm)

Bottom Bottom
",1˝
(1.58 mm)
Figure O – Twist
Figure M – Plumbness
19
ANSI A250.11-2012
Annex B
(informative)
Installation Exceptions
The installation instructions contained in ANSI A250.11 are intended to apply to most typical frame
installations. There are, however, certain types of frames for which additional wood spreaders are
recommended during the frame installation to ultimately assure the proper door operation.
Three-sided frames with face dimensions of 1-½˝ or less of any opening size, frames for doors
that weigh over 9 lbs. per square foot and/or frames of heights greater than 8'-0˝ are more prone
to variations in installed tolerances. Under most conditions, frames such as these require more
support during the installation process.
For installations such as these, the SDI recommends the use of wood spreaders at the bottom
of frames AND at 36˝ intervals between the top and bottom as indicated in the illustration below.
90° 90°
Wood
36" spreader
between
jambs
36" Wood
spreader
between
jambs
20
MEMBERS OF THE
Ceco Door
Milan, TN 38358
Curries
www.deansteel.com
Test Procedures
(909) 770-5700
HOLLOW METAL XPRESS
623-936-7000
www.meskerdoor.com
Corbin, KY 40701
155 Republic Drive
www.secmet.com
9017 Blue Ash Road
(513) 745-6400

440.899.0010 • FAX 440.892.1404
12/4/2014
www.steeldoor.org
ANSI A250.13-2014
Revision of ANSI A250.13-2008
Testing and Rating of —

Severe Windstorm Resistant Components for
Swinging Door Assemblies for Protection of
Building Envelopes
ANSI A250.13-2014
SPONSORS
Steel Door Institute and
ANSI ®
A250.13-2014
Revision ANSI A250.13-2008

Testing and Rating of —
Severe Windstorm Resistant Components for Swinging

Door Assemblies for Protection of Building Envelopes
Secretariat


that all views and objections be considered, and that a concerted effort be
made toward their resolution.
The use of American National Standards is completely voluntary; their
existence does not in any respect preclude anyone, whether they have ap-
proved the standards or not, from manufacturing, marketing, purchasing, or
using products, processes, or procedures not conforming to the standards.
withdrawn at any time. The procedures of the American National Standards
Institute require that action be taken periodically to reaffirm, revise, or
withdraw this standard. Purchasers of American National Standards may
receive current information on all standards by calling or writing the Ameri-
can National Standards Institute.
Published by



ANSI A250.13-2014
Contents
Page
Foreward.. ............................................................................................ ii
1 Scope............................................................................................1
2 Definitions......................................................................................1
3 General..........................................................................................2
4 Overview........................................................................................2
5 Door Frames..................................................................................3
6 Hinges...........................................................................................7
7 Latching Hardware.........................................................................8
8 Doors........................................................................................... 11
9 Door Light Kits............................................................................. 13
10 Sidelights and/or Transoms.. ......................................................... 13
11 Miscellaneous Components.......................................................... 14
12 Selection Criteria......................................................................... 15
Figures
1 Wall Substrates for Frame Tests....................................................4
2 Door Reinforcement for Frame Tests.............................................5
3 Pendulum Impactor.......................................................................6
4 Impact Locations for Frame Tests..................................................6
5 Hinge Structural Load Test Fixture................................................7
6 Lockset Test Fixture......................................................................9
7 Impact Locations for Multi-Point Latch Test................................. 10
8 Impact Locations for Center Mullion Test..................................... 14
Tables
1 Stiffness Classification................................................................. 11
2 Example Door Rating Data........................................................... 12
i
Suggestions for improvement gained in the use of this standard will be wel-
come and should be sent to the Steel Door Institute, 30200 Detroit Road,
Cleveland, Ohio, 44145-1967.
American Institute of Architects/ARCOM
FM Approvals
National Wind Institute / Texas Tech
Underwriters Laboratories LLC
Therma-Tru
Allegion........................................................................................ Karen Bishop
Architectural Testing .................................................................... Dan Johnson
Builders Hardware Manufacturers Association............................ Mike Tierney
Curries Company ........................................................................ Dave Dedic
Deansteel Manufacturing Company............................................ Claus Heide
Door and Hardware Institute........................................................ Greg Drake, AHC
Door Components Inc.................................................................. Tom Popow
Metal Products, Inc...................................................................... Tom Stone
National Wind Institute................................................................. Larry Tanner
Security Metal Products Corp...................................................... Terry Simpson
Underwriters Laboratories LLC.................................................... Luke Woods
Vetrotech Saint-Gobain................................................................ Christian Mueller
ii
AMERICAN NATIONAL STANDARD ANSI A250.13-2014
Testing and Rating of Severe Windstorm

Resistant Components for Swinging Door Assemblies for
Protection of Building Envelopes
1 Scope It is recognized that products and assemblies
meeting these requirements will not necessarily
1.1 This standard provides procedures for testing
prevent all forms of damage associated with hur-
and establishing load ratings (design pressure in
ricanes and other severe windstorms. It is also as-
pounds per square foot or design load in pounds
sumed that these assemblies themselves might be
force) for components of exterior swinging door
damaged in a severe windstorm to an extent that
assemblies for purposes of protection of openings
would require repair or replacement after such an
in building envelopes during severe windstorm
event.
conditions, such as a hurricane, that produces
sustained wind speeds or gusts in a range of 110
2 Definitions
to 150 miles per hour as defined by ASCE 7. It is
not intended to simulate wind forces generated by Building Envelope: Windows, doors, curtain
tornadoes. These products are for non-life safety walls, wall and roof assemblies.
installations and not for use in storm shelters. Life
Classified: Products or materials of a specific
Safety/Shelter products must meet FEMA 320/361
group category that are constructed, inspected,
and/or ICC-500.
tested and subsequently reinspected in accor-
1.2 The procedures cover all components nor- dance with an established set of requirements.
mally assembled to form an exterior swinging door The classification process is performed by an or-
system. This includes door frames, hardware mul- ganization acceptable to the authority having ju-
lions, thresholds, frame anchorage, hinges, lock- risdiction.
sets, latches and bolts, doors, sidelights, transoms
Component: Any of several manufactured items,
and glazing systems. This procedure applies to
classified / listed and labeled, used in the con-
both single swing and pair assemblies and also
struction and installation of a swinging door as-
includes procedures for testing and rating compo-
sembly. Components include door frames, doors,
nents for both in-swing and out-swing installations.
hardware, glazing systems and similar products
1.3 The evaluations required by this standard are normally supplied separately to a job-site where
based on the performance tests specified in ASTM they are assembled and / or installed to form a
E1886, ASTM E1996 and ASTM E330. complete assembly.
1.4 Evaluations under this procedure are designed Design Load: The specified point force applied to
to determine the ability of exterior doors to remain a product. Units of measure are pounds force (lbf).
closed under conditions present in severe wind-
Design Pressure: The specified force applied to
storms, including high, fluctuating wind speeds
a specified unit area of product surface. Units of
and the presence of wind-born debris. Assemblies
measure are pounds-force per square foot (psf).
meeting these requirements are less likely to open
during a storm, preventing potentially large pres- Impact Energy (Kinetic Energy - KE): The spec-
sure differentials which may cause or contribute to ified dynamic load applied to a product. Units of
major structural damage. This procedure does not measure are foot-pounds (ft-lbf).
consider it necessary for the door assembly to be
In-Swing Door: A door with the push side on
capable of preventing water intrusion as a result of
the exterior or that swings into the building when
severe windstorm exposure conditions.
1
ANSI A250.13-2014
opened. Negative pressure acts to close this door pound. Appendix A contains a table of the Imperial
and positive pressure acts to open this door. values used in this standard and corresponding SI
values.
Labeled: Equipment or materials to which has
been attached a label, symbol, or other identifying 3.1.2 Unless specifically indicated otherwise, tol-
mark of an organization that is acceptable to the erances shall be in accordance with Appendix A.
Authority Having Jurisdiction (AHJ) and concerned
3.1.3 Where load ratings are to be applied in
with product evaluation, that maintains periodic in-
units of pounds per square foot (psf), these val-
spections of production of labeled equipment or
ues shall be expressed in 5-pound-per-square-
materials, and by whose labeling the manufacturer
foot increments. For components that are rated in
indicates compliance with appropriate standards
terms of pounds force, values shall be expressed
or performance in a specified manner.
in 10-pound increments. All rated values shall be
Listed: Equipment materials or services included determined by rounding down from values derived
in a list published by an organization that is accept- from tests.
able to the Authority Having Jurisdiction (AHJ) and
3.2 Referenced Standards
concerned with evaluation of products or services,
that maintains periodic evaluation of services and 3.2.1 ANSI/ASCE 7-10, Minimum Design Loads
whose listing states that either the equipment, ma- for Buildings and Other Structures
terial, or service meets identified standards or has
3.2.2 ANSI/SDI A250.4-2011, Test Procedure and
been tested and found suitable for a specified pur-
Acceptance Criteria for Physical Endurance for
pose.
Steel Doors, Frames, Frame Anchors and Hard-
Operable: Capable of being opened by the ap- ware Reinforcings
plication of ordinary levels of applied force to the
3.2.3 ASTM E330-02 (2010), Standard Test
latch operator and door assembly.
Method for Structural Performance of Exterior
Note: Door assemblies that have been subjected Windows, Doors, Skylights and Curtain Walls by
to the severe conditions of the tests involved in this Uniform Static Air Pressure Difference
method are not expected to be undamaged and
thus will normally not operate with the low force lev- 3.2.4 ASTM E1886-05, Standard Test Method for
els generally required for undamaged assemblies. Performance of Exterior Windows, Curtain Walls,
The goal is to provide an assembly that will remain
closed during the windstorm, but not be damaged Doors, and Storm Shutters Impacted by Missile(s)
to the extent that it requires the use of tools to be and Exposed to Cyclic Pressure Differentials
opened after the event.
3.2.5 ASTM E1996-12a, Standard Specification
Out-Swing Door: A door with the pull side on for Performance of Exterior Windows, Curtain
the exterior or that swings away from the building Walls, Doors and Storm Shutters Impacted by
when opened. Negative pressure acts to open this Windborne Debris in Hurricanes
door and positive pressure acts to close this door.
3.2.6 ASTM F476-84 (2002) Standard Test Meth-
Severe Windstorm: A weather event such as a ods for Security of Swinging Door Assemblies
hurricane that produces sustained wind speeds or
gusts in a range of 110 to 150 miles per hour. 3.2.7 ANSI/BHMA A156.1-2013, Butts and Hinges
Stiffness Classification: A measure of a door’s 3.2.8 ANSI/BHMA A156.16-2008, Auxiliary Hard-

resistance to bending as determined by a twist test ware
under a prescribed loading condition.
4 Overview
3 General 4.1 The procedures in this document are de-
signed to evaluate each critical component used
3.1 Units of Measurement
in a swinging door assembly for the component’s
3.1.1 When a value for measurement is followed ability to perform its intended function. The evalu-
by a value in other units in parentheses, the sec- ation is conducted under the conditions of stress
ond value is only approximate. The first stated val- and loading the component would be subjected to
ue is the requirement. The primary units are inch- in the testing of a complete assembly under the
2
ANSI A250.13-2014
assembly test methods commonly specified for Section 11.1 – Hardware Mullions
severe windstorm resistance.
Section 11.2 – Thresholds
4.2 The tests and evaluations required by this pro-
cedure include both the application of engineering 5 Door Frames
safety factors and worst-case analysis to ensure
that component substitutions in field assemblies 5.1 Frames are to be evaluated in the largest door
will perform to the minimum levels expected. opening sizes, minimum jamb depth and minimum
frame material thickness for which a design rat-
4.3 Components evaluated by this method are ing is to be determined. Frames intended for use
classified into various strength categories that can in both single swing and pair assemblies shall be
be used to determine assembly ratings. A single tested in both configurations. Frames are to be
component may have multiple ratings depending installed following the manufacturer’s written in-
on various parameters such as size, number and structions which are to include:
location of anchors or fasteners, type of surround-
ing construction and other factors. Proper appli- a) Wall substrate – wood/steel stud, con-
cation of these ratings allows for the determina- crete, masonry, structural steel.
tion of an assembly’s design pressure rating and b) Anchors – number, size, type and spac-
minimum impact energy resistance. These ratings ing of anchors, anchor or bolt embedment,
are intended to be used to determine compliance and number and type of fasteners required
with code requirements developed for complete at each anchor location.
assemblies.
c) Reinforcements – location and attach-
4.3.1 Doors are rated for design pressure in ment.
pounds per square foot (psf), impact energy in
foot-pounds (ft-lbf) and stiffness classification. d) Gasketing – location, type and attach-
Stiffness is required in determining the interaction ment.
between the door bending under load, transmis- e) Hinges – number, type, size and locations.
sion of impact energy to latching hardware and
frames, and latching engagement. f) Latching Hardware – type and location.
4.4 Proper application of this standard requires a 5.2 Test Procedure

basic level of understanding of physics, mechan- 5.2.1 Static Pressure Test
ics and materials science.
5.2.1.1 The frame shall be installed into a test unit
4.5 This procedure provides specific tests and rat- constructed to simulate the wall design specified
ing methods for the following components: by the frame manufacturer. The frame installation
Section 5 – Door Frames shall be in accordance with the frame manufac-
turer’s written instructions (refer to figure 1 for typi-
Section 6 – Hinges cal details). For wall designs that differ significantly
Section 7 – Latching Hardware from those shown, the test installation shall simu-
late actual intended wall design and anchorage.
Section 7.1 – Locksets (Bored, Mortise, Deadbolts)
A flush door rated for not less than the desired
Section 7.2 – Single Point Rim or Mortise Exit De- frame design pressure shall be mounted with the
vices number of hinges specified by the frame manu-
Section 7.3 – Multi-point Latches (including flush facturer. For single-swing frames, a single-point
and surface bolts) simulated latch and a stainless steel strike shall be
installed between 38˝ and 42˝ above the bottom
Section 8 – Doors of the frame (see figure 2.) The door and latch-
Section 9 – Door Vision Light Kits ing hardware shall be of sufficient strength so that
they do not fail at the required test load. Door (s)
Section 10 – Sidelight and Transom frames shall be installed in the direction of swing for the
Section 11 – Miscellaneous Components desired listing.
3
ANSI A250.13-2014
Figure 1 – Wall Substrates for Frame Tests
5.2.1.2 For pair frames, two flush doors rated 5.2.1.3 The frame and door assembly shall be in-
for not less than the desired frame design pres- stalled in a static pressure test chamber per the
sure shall be installed with a simulated latching requirements of ASTM E330.
arrangement with a top and bottom bolt on the
5.2.1.4 The assembly shall be subjected to a static
inactive door and a single point latch on the ac-
pressure equal to 1.5 times the design pressure
tive door latching into the inactive door. The doors
rating specified by the frame manufacturer under
used are to be reinforced as described in 5.2.1.2.1
both positive and negative pressure. Each pres-
and latched as shown in figure 2.
sure cycle shall be applied for a minimum of 30
If the manufacturer specifies other latch/lock lo- seconds, then released and reduced to zero.
cations, tests shall be conducted under specified
5.2.1.5 At the conclusion of this test, the frame
conditions and the resulting rating shall specify the
shall not prevent the door (s) from operating after
latching requirements.
the simulated latch bolt (s) has been retracted and
5.2.1.2.1 The flush door used shall be reinforced a 15 pound force is applied at the mid-height of the
along the latch or meeting edge by bolting a 1-1/4 door, horizontally 1 inch from the lock edge. The
inch by 1-1/4 inch by 3/16 inch structural steel angle frame shall remain in the opening.
to both faces of the door with 1/4-20 bolts at 16 (±) 1
inches on center and within 6 (±1) inches of the 5.2.2 Impact Test
corners. The angle shall be placed such that the 5.2.2.1 Upon completion of the static pressure
free leg of the angle is oriented toward the edge of test an identical assembly shall be subjected to
the door and is located at 3 inches from the door impacts with an impact energy of 350 foot-pounds.
latch edge (see figure 2).
4
ANSI A250.13-2014
The impact energy shall be delivered by one of the 5.2.2.2.2 Pair Frames
following two methods:
Six impacts in accordance with Figure 4.
Method 1 – Deliver impact energy by a 100-pound
5.2.3 At the conclusion of this test, the frame shall
total weight pendulum impactor fitted with a num-
not prevent the door (s) from operating after the
ber 2 or better, 12-inch-long Douglas Fir or South-
simulated latch bolt (s) has been retracted and a
ern Yellow Pine, nominal 2 by 4 striking face. The
15-pound force is applied at the mid-height of the
pendulum is to be suspended in a manner that as-
door, 1 inch horizontally from the lock edge. The
sures a direct normal impact to the door assembly.
frame shall remain in the opening.
Refer to ASTM F476 for details of a comparable
pendulum impact device (see figure 3). 5.3 Cycle Test
Method 2 – Deliver the impact energy in accor- 5.3.1 Upon completion of the impact tests speci-
dance with the impact method defined in ASTM fied in 5.2, the same assembly shall be subjected
E1996 using a 9 pound 2 x 4 missile impacting to the pressure cycling test specified in ASTM
end-on at a velocity of 50 feet per second. E1886.
5.2.2.2 Impacts are to be delivered to the exterior 5.3.2 At the conclusion of this test, the frame shall
side of the door (s) per ASTM E1886. Impact loca- not prevent the door (s) from operating after the
tions as described below and as shown in figure simulated latch bolt (s) has been retracted and a
4). 15-pound force is applied at the mid-height of the
5.2.2.2.1 Single Frames door, 1-inch horizontally from the lock edge. The
frame shall remain in the opening.
Five impacts in accordance with Figure 4.
Figure 2 – Door Reinforcement for Frame Tests
5
ANSI A250.13-2014
Figure 3 – Pendulum Impactor
Figure 4 – Impact Locations for Frame Tests
6
ANSI A250.13-2014
5.4 Frame Ratings inches from the hinge centerline using the pendu-
lum impactor specified in figure 3. Shearing of any
5.4.1 Frames that meet the criteria specified in
fastener or deformation of the hinge which renders
this section shall be rated for the design pressure
the hinge inoperable shall constitute a failure. The
attained in the evaluation and for impact energy
simulated door section shall be tested as an in-
resistance. Ratings shall be specific to positive
swinging door.
and negative design pressure configuration (sin-
gle/pair, in-swing/out-swing) and shall apply to all NOTE: Impact energy specified delivers approxi-
overall frame sizes (not to exceed either height or mately twice the energy to the hinge as occurs in
a typical door assembly test using a 9 pound 2 x 4
width of frame tested) equal to or smaller than the missile at 50 feet-per-second.
frame tested.
6.1.1.2.1 Exception
6 Hinges Hinges listed only for use in out-swing door as-
semblies do not require an impact test.
6.1 Leaf Hinges
Three representative specimens shall be tested. 6.1.2 Structural Load Test
Ratings shall be based on the lowest load suc- 6.1.2.1 The test assembly described in 6.1.1.1
cessfully sustained by all three specimens. shall be mounted in a testing machine and loaded
at a rate of 0.05 inches per minute until failure. The
6.1.1 Impact Test
load shall be applied through a 3/4-inch diameter
6.1.1.1 Hinges shall be mounted for testing in the roller and 1/4-inch thick by 3-inch wide steel plate in
test fixture shown in figure 5. Hinges are to be a manner that places the attachments in shear on
mounted to the simulated frame and door sections the push side of the simulated door section. The
using screws provided by the hinge manufacturer. load at failure shall be recorded.
6.1.1.2 One 125 foot-pound impact shall be de-
livered to the simulated door section at a point 6
Simulated Frame
9" x 1-1/4" x 3/16"

Steel Hinge Apply load through
Reinforcements 1/4" x 3" wide steel
bearing plate, placed
on, not welded to door,
and 3/4" roller
1/4" Thick
Structural Steel
Hinge Under Test
Figure 5 – Hinge Structural Load Test Fixture
7
ANSI A250.13-2014
6.1.3 Rating 6.2.5 Throughout the tests described in section

6.2 the door shall remain secured in the frame and
6.1.3.1 Hinges shall be rated for a design load
shall be operable at the conclusion of the tests.
based on the lowest ultimate load value deter-
mined in 6.1.2.1, divided by a safety factor of 1.5. 6.2.6 Rating
6.2 Continuous Hinges and Pivots 6.2.6.1 Continuous hinges and pivots shall be rat-
ed for the impact energy resistance in foot-pounds
6.2.1 Continuous hinges and/or pivots shall be
and design pressure in pounds per square foot
tested in the maximum length with the minimum
and maximum size, based on the tested assem-
number of fasteners supplied by the manufacturer.
bly size for which they successfully complete the
Continuous hinges and/or pivots are to be tested
required testing.
applied to a simulated door as described in section
5.2.1.1 and a frame assembly designed to with-
7 Latching Hardware
stand the loads required to evaluate the hinge and/
or pivots to the level required. A simulated frame 7.1 Locksets
constructed from 4-inch to 6-inch wide structural
steel channel and with a solid steel stop 1-inch 7.1.1 Impact Test
wide by 5/8-inch high is suitable for this purpose. 7.1.1.1 Locksets shall be mounted in the test fix-
Pivots and continuous hinges shall be tested us- ture described in figure 6. Mounting shall be in
ing the maximum size of door for which a rating is accordance with the lock manufacturer’s instruc-
desired. tions. Locksets are to be in the locked mode for
6.2.2 Static Pressure Test all tests.
6.2.2.1 Apply a pressure equal to 1.5 times the 7.1.1.2 Strikes shall be mounted to the simulated
hinge manufacturer’s specified design pressure frame section using the screws provided by the
per ASTM E330 in both positive and negative di- lock manufacturer.
rections. Hold each load for a minimum of 30 sec- 7.1.1.3 One 125 foot-pound impact shall be deliv-
onds, then release. ered to the test fixture (push side) at a point 6 inch-
es from the simulated door edge using the pen-
6.2.3 Impact Test
dulum impactor specified in figure 3. If the lockset
6.2.3.1 Using either the same assembly used for handle or other parts are in the indicated impact
the static pressure test or an identical assembly, area, the impact location shall be moved upward
at the manufacturer’s option, conduct three impact sufficiently to avoid hitting the parts.
tests using one of the impact test methods de-
NOTE: Impact energy specified delivers approxi-
scribed in 5.2.2.1 at the following locations against mately twice the energy to the latch as occurs in a
the push side of the door. typical door assembly test using a 9 pound 2 x 4 mis-
sile at 50 feet-per-second.
6.2.3.1.1 Impact 6 inches down from the top and
6 inches horizontally from the hinge edge of the 7.1.2 Structural Load Test
door.
7.1.2.1 Upon completion of the impact test speci-
6.2.3.1.2 Impact the mid-height of the door 6 inch- fied in section 7.1.1, the test fixture and the same
es from the hinge edge. specimen (figure 6) shall be mounted in a testing
machine. A load shall then be applied equal to 1.5
6.2.3.1.3 Impact 6 inches up from the door bottom
times the manufacturers’ designated design load.
and 6 inches from the hinge edge.
The load shall be applied through a 3/4-inch roller
6.2.4 Cycle Test and 1/4-inch by 3-inch steel loading plate of suffi-
cient width to span the simulated door portion of
6.2.4.1 Upon completion of the impact tests, the the test fixture. This load shall be held for 30 sec-
same assembly shall be cycled per ASTM E1886. onds and then released.
7.1.2.2 Upon completion of the structural test the
lockset shall be operable.
8
ANSI A250.13-2014
Aluminum block
machined to fit
Reinforcement notched lockset.
so that latch bolt is
supported only by strike.
Apply load through

1/4" x 3" wide steel 1/4" thick structural
bearing plate, and steel tube
3/4" roller.
Figure 6 – Lockset Test Fixture
7.1.3 Lockset Rating 7.2.3 Static Pressure Test

7.1.3.1 The lockset rating shall be the design load 7.2.3.1 Upon completion of the impact tests speci-
and impact energy specified by the manufacturer fied in 7.2.2.1, the same assembly shall be mount-
and verified by acceptable results in the impact ed in a static pressure test chamber and tested per
and structural load test described in this section. ASTM E330.
7.2 Single Point Rim and Mortise Exit 7.2.3.1.1 Apply 1.5 times the manufacturer’s spec-
Devices ified design pressure to the push side of the door.
Hold for a minimum of 30 seconds and release.
7.2.1 Single point rim and mortise exit devices
shall be mounted on a door of the stiffness clas- 7.2.3.1.2 Upon completion of the test the single
sification and maximum size for which a rating is point rim or mortise exit device shall be operable.
to be determined. Mounting shall be in accordance 7.2.4 Rating of Single Point Rim and
with the device manufacturer’s instructions.
Mortise Exit Devices
7.2.2 Impact Test 7.2.4.1 Single point rim or mortise exit devices
7.2.2.1 One 350 foot-pound impact shall be deliv- shall be rated for the design pressure in pounds
ered to the pull side of the door using one of the per square foot, impact energy resistance in foot-
impact test methods described in section 5.2.2.1. pounds, maximum pair or single door leaf size,
If hardware location interferes with the specified and door stiffness classification specified by the
locations for impacts the impact shall be located device manufacturer and verified by acceptable
as close to the specified location as possible in a results in the impact and structural load test de-
manner that avoids impact on the hardware. scribed in this section.
7.2.2.2 Upon completion of the impact tests the 7.3 Multi-Point Latches
door shall remain latched and the single point rim
7.3.1 Multi-point latches shall be mounted on the
or mortise exit device shall be operable.
maximum size pair of the minimum stiffness class
doors specified by the manufacturer for testing.
9
ANSI A250.13-2014
Note: Since many exterior doors are used as a as close to the specified location as possible in a
required “means of egress”, building codes do not manner that avoids impact on the hardware.
generally allow the use of additional manual bolts
and locks on these doors. That is, it must be possible, 7.3.2.2 When other hardware is being evaluated
under emergency conditions, for these doors to be
opened with a single manual operation. The use of
simultaneously with bolts (surface or flush type) to
auxiliary latching devices as a means of increasing increase the overall rating, then a fourth impact is
the windstorm resistance rating of an assembly to be made at the centerline of the other hardware
should be verified for acceptability under prevailing and 6 inches from the meeting door edge.
building code requirements.
7.3.2.3 Upon completion of the impact tests the
7.3.2 Impact Test multi-point latch shall be operable.
7.3.2.1 The door containing the device under test
7.3.3 Static Pressure Test
(active leaf) shall be subjected to three 350 foot-
pound impacts using one of the impact test meth- 7.3.3.1 Upon completion of the impact test, the
ods described in Section 5.2.2.1 to the pull side same assembly shall be tested on the impact as-
of the door. One impact is to be made at the up- sembly or mounted in a test chamber and tested
per meeting edge of the door 6 inches below the per ASTM E330 under uniform static pressure.
top edge of the door and 6 inches from the meet-
7.3.3.2 Starting at the design pressure specified
ing edge. The second impact is to be made at the
by the manufacturer, apply the pressure in 5 psf
lower meeting edge of the door 6 inches above the
increments in both positive and negative direc-
bottom and 6 inches from the meeting door edge.
tions until failure occurs. Each pressure increment
The third impact is to be made at the center of the
shall be held for a minimum of 10 seconds in each
door opposite and 5 inches below the push bar.
direction.
If hardware location interferes with the specified
locations for impacts the impact shall be located
Figure 7 – Impact Locations for Multi-Point Latch Test
10
ANSI A250.13-2014
7.3.3.3 After each pressure increment, remove sample of the full flush panel (no hardware prepa-
the pressure and check the hardware for oper- rations) door construction under investigation.
ability. One pressure increment consists of both a
8.2.1.1 Mount the door panel in a rigid test frame
positive and negative pressure.
and clamp the bottom two corners and one top
7.3.3.4 Record mode of failure and pressure in- corner securely to the frame.
crement at failure.
8.2.1.2 Apply a load of 300 lbf through a 2.5 inch
7.3.4 Multi-Point Latch Rating diameter by 1/4-inch thick steel pad to a point cen-
tered 3 inches down and 3 inches horizontally from
7.3.4.1 Multi-Point latches shall be rated for the the free corner of the door per ANSI A250.4.
design pressure in pounds per square foot, impact
energy resistance in foot-pounds, maximum pair 8.2.1.3 Measure the door deflection at the free
or single door leaf size, and door stiffness classi- corner, as described in ANSI A250.4, to the near-
fication specified by the device manufacturer and est 0.01 inch.
verified by acceptable results in the impact and
8.2.2 Classifications
structural load test described in this section as fol-
lows: 8.2.2.1 Doors shall be classified for stiffness as
follows in Table 1 based on the results of the twist
7.3.4.1.1 For pairs of doors with four or more
test.
points of latching, the design pressure is the maxi-
mum test pressure increment that did not result in
Table 1 – Stiffness Classification
failure as determined by 7.3.3.3 divided by a safety
factor of 1.5.
Corner Deflection Stiffness Class
7.3.4.1.2 For pairs of doors with single point latch-
≤ 0.5 inch I
ing on the active leaf and multi-point latching on
the inactive leaf as described in 7.3.2.1, the de- > 0.5 inch and ≤ 1.0 inch II
sign pressure is the maximum test pressure incre- > 1.0 inch and ≤ 2.0 inches III
ment that did not result in failure as determined by > 2.0 inches and ≤ 3.0 inches IV
7.3.3.3 divided by a safety factor of 1.5. > 3.0 inches V
7.3.4.1.3 For pairs of doors with single point latch-
ing on the active leaf and multi-point latching on
the inactive leaf as described in 7.3.2.2 with sur- 8.3 Assembly Tests
face or flush bolts per ANSI/BHMA A156.16 Aux- 8.3.1 Doors shall be installed in each assembly
iliary Hardware, mounted on the inactive leaf, the configuration for which a rating is to be deter-
design pressure is the maximum pressure incre- mined. The following list shall be used to select
ment that did not result in failure as determined by the test configurations.
7.3.3.3 divided by a safety factor of 3.0.
8.3.1.1 Single-swing with cylindrical single-point
8 Doors latch.
8.1 Doors shall be tested in the largest size (over- 8.3.1.2 Single-swing with mortise single-point
all area, greatest width, greatest height) for which latch.
a design pressure rating is to be applied. Require- 8.3.1.3 Single-swing with rim or mortise exit de-
ments for framing systems or other reinforcements vice.
in doors shall be specified as defined in the man-
ufacturer’s follow-up inspection procedures. All 8.3.1.4 Pairs of doors swinging in the same direc-
doors of the same design with smaller dimensions tion with 4-point latching – surface rods.
shall be given the same rating as the test door (s). 8.3.1.5 Pairs of doors swinging in the same direc-
8.2 Stiffness Classification tion with 4-point latching – concealed rods.
8.2.1 Doors shall be classified for stiffness by per- 8.3.1.6 Pairs of doors swinging in the same direc-
forming the following twist test on a 3´0˝ by 7´0˝ tion with 3-point latching – surface rods by cylindri-
cal latch.
11
ANSI A250.13-2014
Table 2 – Example Door Rating Data
Door Model: 1234 Stiffness Class II

Maximum Latch Throw Latch Strength Impact Design Pressure
Configuration
Size Min. (in) Min. (lbf) (ft-lbf) (psf)
Single Out-swing (cylindrical) 4-0 x 8-0 1/2 1600 350 100
Single In-swing (mortise) 4-0 x 8-0 1/2 1600 350 100
Single Out-swing (Rim) 3-0 x 8-0 (1) (1) 350 80
Pair w/ 4-Point (CVR by CVR) 8-0 x 8-0 (1) (1) 350 80
Pair w/ 3-Point 8-0 x 8-0 (1) (1) 350 80
Pair w/ 4-Point (CVR by CVR) 6-0 x 7-0 (1) (1) 350 140
(1) Components are rated in design pressure (psf) not latch strength (lbf)
8.3.1.7 Pairs of doors swinging in the same direc- The largest size (maximum area, height, and width
tion with 3-point latching – flush bolts or CVR by of exposed light) of the light kit and the minimum
mortise latch. stile and rail dimensions shall be defined. Re-
quirements for framing systems or other reinforce-
8.3.1.8 Pairs of doors swinging in the same direc-
ments in doors shall be specified as defined in the
tion with 3-point latching-mortise exit device by
vision light kit manufacturer’s follow-up inspection
surface or concealed exit device.
procedures.
8.3.1.9 Pairs of doors swinging in the same direc-
8.3.4 Doors are to be tested installed in frames
tion with 2-point latching – rim exit device with re-
using latching hardware and hinges with a design
movable mullion.
pressure rating greater than or equal to the speci-
8.3.2 A minimum of 3 assemblies shall be tested fied design-pressure rating of the door.
for single-swing configurations and a minimum of
8.3.5 Assemblies which incorporate manual sur-
three assemblies shall be tested for pair configu-
face bolts or other latching hardware intended only
rations. Latching hardware configurations can be
for use in severe storm conditions (hurricanes)
varied between the individual assemblies to pro-
shall be evaluated for design pressure strength
vide coverage per 8.3.1. This includes combining
per ASTM E330 with the additional hardware en-
surface and concealed-rod type hardware in one
gaged. The ratings for such assemblies shall in-
pair assembly to cover configurations from 8.3.1.4
dicate design pressure for the assembly with the
and 8.3.1.5. The resulting ratings will be deter-
additional hardware.
mined separately for pair and single-swing config-
urations. When the three assemblies of one swing 8.4 Test Procedure
type vary, the rating for the door is to be based
on the highest design pressure test passed by all 8.4.1 Each assembly configuration shall be tested
three assemblies. to 1.5 times the design pressure per ASTM E330.
8.3.3 Qualifying Doors for Vision Light Kits – 8.4.2 Each assembly shall be tested to impact and
Where doors are to be qualified to receive light cyclic load tests as specified in ASTM E1886 and
kits, at least one assembly shall be tested with ASTM E1996. (At the discretion of the test sponsor
maximum light kit size desired. This assembly the same or an identical assembly shall be permit-
shall be an assembly or at least one of the assem- ted for the structural test.) For doors designated
blies from 8.3.2. Multiple light kit designs and sizes by the manufacturer as either in-swing only or
may be tested for multiple ratings. The rating for out-swing only, the impact test shall be conducted
the door is to be based on the highest design pres- only from the outdoor side of the assembly. For
sure test passed by the glazed assembly, but shall doors designated as either in-swing or out-swing,
not exceed the rating of the opaque assemblies. the impact tests shall be conducted from the out-
12
ANSI A250.13-2014
side (push side) of in-swinging assemblies on two 9.2 Test Procedure

samples and from the outside (pull side) of an out-
swinging assembly on the third sample. 9.2.1 Static Pressure Test
8.4.3 Assemblies shall remain closed and latched 9.2.1.1 Each assembly configuration shall be
during the tests specified and the active leaf shall tested to 1.5 times the design pressure, per ASTM
be operable at the conclusion of the tests. E330.
9.2.1.2 Install the glazing system into the type and
8.5 Ratings of Doors
size of door specified by the glazing system manu-
8.5.1 Ratings of doors shall include the following facturer. Three identical assemblies are required.
information (see Table 2): The doors shall be mounted in frames and bucks
as required for the standard door test procedure.
1. Maximum Size;
2. Stiffness Classification; 9.2.2 Impact Test
3. Design Pressure Rating for each configu- 9.2.2.1 Test the assembly per ASTM E1886 with
ration type; (this provides consistency in the impacts required applied to the center and one
language); corner of the glazing panel in each assembly.
4. Impact Energy Resistance Classification; 9.2.3 Cycle Test

5. Minimum Latch Throw for single point lock 9.2.3.1 Cycle test each assembly per ASTM
sets; E1886.
6. Minimum Latch Strength for single point 9.2.3.2 Upon completion of the impact and cycle
lock sets. tests there shall be no failure of the glazing sys-
tem as defined in the referenced standard ASTM
9 Door Light Kits E1996.
9.1 Door vision light kits shall be evaluated as 9.3 Glazing System Ratings
complete glazing systems designed for installation 9.3.1 Glazing systems shall be rated at the design
into specific doors. These doors shall have been pressure used in the evaluation and shall include
qualified to receive light kits in accordance with specific doors, minimum door size, and maximum
paragraph 8.3.3. Glazing systems shall include all glazing dimensions (maximum area, maximum
parts necessary to install the glazing in the door. height and maximum width).
This shall normally include at least a glazing pan-
el, frame, sealant or glazing compound and fas- 10 Sidelights and/or Transoms
teners. Requirements for framing systems or other
reinforcements in doors shall be specified as de- 10.1 Sidelights and/or transoms shall be tested
fined in the vision light manufacturer’s follow-up with doors, to the largest total size (maximum
inspection procedures. area, height and width) to be rated. Testing shall
be performed in accordance with ASTM E1886
9.1.1 Glazing systems shall be tested in the larg- and ASTM E1996. Doors used in the evaluation
est size (maximum area, height, width of exposed assembly shall be rated per this method for at
light) to be rated in the smallest standard door size least the design pressure specified for the side-
(minimum 3´0˝ x 7´0˝) that can accommodate the light/transom assembly.
glazing system.
10.2 Installation of sidelight and/or transom as-
9.1.2 Alternately, glazing systems shall be tested semblies shall be per manufacturer’s instructions.
as part of door assemblies as defined in para- Frames for these assemblies shall be evaluated for
graph 8.3.3. In this case, the largest size (maxi- installation in each wall type for which the product
mum area, height, and width of exposed light) of is intended. Installation instructions shall include:
the light kit and the minimum stile and rail dimen- glazing material, sealants or glazing compounds,
sions shall be defined. installation procedures, and details of frame an-
choring methods.
13
ANSI A250.13-2014
10.3 Ratings for Sidelight and/or Tran- used for this test shall be stiffened as described
som Assemblies in section 5.2.1.2.1, except that surface applied re-
inforcements are to be removed in areas required
10.3.1 Sidelight and/or transom assemblies that for mounting the latching device. Doors are to be
meet the criteria specified in this section shall be equipped with rim exit devices or other hardware
rated for the design pressure attained in the evalu- as specified by the manufacturer.
ation and for impact energy resistance. Ratings
shall be specific to positive and negative design 11.1.2 Static Pressure Test
pressure configuration (single/pair, in-swing/out-
11.1.2.1 Load the assembly to 1.5 times the de-
swing) and shall apply to all overall assembly sizes
sign pressure in accordance with ASTM E330 in
(not to exceed either height or width of assembly
both positive and negative directions. The pres-
tested) equal to or smaller than the assembly test-
sure load shall be maintained for a minimum of 30
ed.
seconds.
11 Miscellaneous Components 11.1.3 Impact Test
11.1 Center Mullions Prepared for Hard- 11.1.3.1 On the same assembly used in the struc-
ware tural test or an identical assembly, at the manu-
facturer’s option, apply four impacts of 350 ft-lbf
11.1.1 Center mullions prepared for hardware using one of the impact test methods described in
shall be tested at the maximum height specified section 5.2.2.1. One impact is to be applied at the
by the manufacturer. Install the mullion in a frame meeting edge of the doors 6 inches down from the
of the maximum width for which a rating is desired head jamb. The second impact is to be applied at
following the manufacturer’s instructions. Doors the meeting edge of the doors 6 inches up from
Impact Locations
Figure 8 – Impact Locations for Center Mullion Test
14
ANSI A250.13-2014
the sill and the third impact applied at the center- described in section 5.2.2.1 to a location on the
line of the latch and 6 inches horizontally from the centerline of any latching device that engages into
latch edge of the door. Apply a fourth impact at the sill at a point 6 inches up from the sill. If the
the center of the other door 5 inches below the assembly includes two latching locations, two im-
latch. Upon completion of the impact tests, con- pacts are required.
duct cycle testing as specified in ASTM E1886. At
the completion of these tests the hardware mullion 11.2.6 Cycle Test
shall remain in place and the door assembly shall 11.2.6.1 The same assembly used for the impact
be operable. test in 11.2.3 shall be subjected to the cyclic pres-
11.1.4 Hardware mullions shall be rated for the sure test prescribed by ASTM E1886.
impact energy successfully passed and for the 11.2.7 Upon completion of these tests, the door
design pressure tested in the static pressure and assembly shall be operable and the threshold
cycle tests. shall remain in place.
11.2 Thresholds 11.2.8 Thresholds shall be rated for the impact
energy successfully passed and for the latching
11.2.1 Thresholds are only evaluated for their abil-
load established in the structural load and cycle
ity to retain latch bolts and strikes and remain se-
tests. Latching load (lbf) shall be calculated as de-
cured to underlying construction when subjected
sign pressure (psf) times the area (square feet) of
to anticipated structural and impact energy loads.
the opening divided by 4 (the equivalent of one-
11.2.2 Thresholds are to be tested in conjunc- quarter of the total load).
tion with hardware mullions as described in sec-
tion 11.1 when applicable. Thresholds that are 12 Selection Criteria
designed for direct attachment of latching devices
shall be tested as follows. 12.1 The following process is used to determine
Swinging Door Assembly Ratings for Severe
11.2.3 Thresholds shall be tested at the maximum Windstorm Resistance from Component Ratings.
door opening width to which the resulting rating
is to be applied. Thresholds shall be installed in a 12.1.1 The first step in determining if an assembly
test assembly using a frame and stiffened doors meets a code requirement for severe windstorm
(per 5.2.1.2.1) known to be capable of sustaining resistance is for the building designer to determine
the required test pressure. Thresholds shall be at- the required performance level for the opening.
tached to a simulated floor using the number, size This shall include a calculation of the required
and location of fasteners specified by the manu- minimum design pressure in pounds per square
facturer. The set-up shall be for single-point latch- foot and the determination of whether or not im-
ing on the active leaf and two-point latching on the pact resistance is required. In most cases ASCE
inactive leaf with the bolt and strike specified by 7 is specified by the applicable building code and
the manufacturer. requires a thorough analysis of the building de-
sign and location to determine design pressure
11.2.4 Static Pressure Test for each opening. State and local building codes
11.2.4.1 The test assembly shall be subjected will generally specify when impact resistance is
to 1.5 times the design pressure specified by the required and at what level.
manufacturer in both positive and negative direc- 12.1.2 If impact resistance is required, each com-
tions as required by ASTM E330. The pressure in ponent of the opening shall have an impact rating
each direction shall be maintained for a minimum equal to or greater than the impact energy required
of 30 seconds. for the opening.
11.2.5 Impact Test 12.1.3 Determine the wall construction type for the
11.2.5.1 The same assembly or an identical as- opening (masonry, wood frame, steel, etc.). The
sembly which has not been subjected to the 1.5 selected frame and anchorage method must meet
times design load test shall be used for this test at or exceed the design pressure and impact energy
the manufacturer’s option. Impacts (350 ft-lb) shall requirements for the opening. The size at which
be applied using one of the impact test methods
15
ANSI A250.13-2014
the frame is rated must be equal to or greater than 12.1.6 To select a rim exit, mortise exit, hardware
the size requirement for the opening. mullion, or multi-point latch configuration, com-
pare the rated hardware design pressure, impact
12.1.4 Determine the type of hinge needed for the
energy requirement, stiffness classification, and
application. Leaf and butt hinges are expressed
door size with the opening requirements.
in lbs force. To select leaf or butt hinges, multiply
the design pressure by the tributary area in square 12.1.7 If a light kit is to be installed, select a light
feet for each hinge to determine the required hinge kit with a design pressure and impact energy rat-
design load in pounds force (lbf). Select a hinge ing equal to or greater than the required values.
that meets or exceeds the design load and impact
12.1.8 To select a door leaf compare the rated
energy requirements for the opening (see exam-
design pressure, desired hardware configuration,
ples in Appendix B).
impact energy, and size requirements with the
12.1.4.2 Continuous hinges and pivots are rated opening requirements. Obtain the design pres-
for design pressure, impact energy and door leaf sure rating for the specified hardware configura-
size. The design pressure and impact energy rat- tion by checking the door rating data (see example
ing for the selected continuous or pivot hinge must in table 2). The rated door panel design pressure
meet or exceed the requirements for the opening. for the desired hardware configuration, impact en-
The required door size for the opening must be ergy, and size must meet or exceed the require-
equal to or less than the door size listed for the ments for the opening. If rim exits or mortise exits
hinge. are specified, the door panel must meet or exceed
the door stiffness classification for the rim or mor-
12.1.5 To select cylindrical lock or mortise lock
tise exit device being used.
for a door leaf, determine the latch bolt design
load (lbf) required, by multiplying one-half of the 12.1.9 All components must be installed in accor-
nominal door leaf area in square feet by the design dance with the component manufacturer’s instruc-
pressure. Select a lock with a design load rating tions. The assembly rating is equal to the lowest
(lbf) equal to or greater than the calculated latch design pressure rating of the selected components
design load (see examples in Appendix B). and must be equal to or greater than the design
pressure required for the opening.
16
ANSI A250.13-2014
Appendix A
(normative)
Tolerances and Conversion of Measurements to SI
Imperial Imperial SI
Imperial Unit SI Value SI Unit
Value Tolerance Tolerance
110 MPH NA 177 KMH NA
150 MPH NA 241 KMH NA
5 PSF ±0.5 239 Pa ±24
10 PSF ±0.5 479 Pa ±24
60 in ±0.25 1524 mm ±6
30 in ±0.25 762 mm ±6
40-5/16 in ±1/8 1024 mm ±3
1-1/4 in ±1/8 1024 mm ±3
3/16 in ±1/32 4.8 mm ±1
16 in ±1 406 mm ±25
6 in ±1 152 mm ±25
3 in ±1/8 76 mm ±3
15 lbf ±0.5 67 N ±2
1 in ±1/16 25 mm ±2
350 ft-lb ±3.5 475 N-M ±5
100 lb ±1 45.4 Kg ±0.5
12 in ±1/8 305 mm ±3
24 in ±1/8 610 mm ±3
50 ft/sec NA 1.52 Km/Sec NA
0.05 in/min ±0.005 1.3 mm/min ±0.1
300 lbf ±3 1334 N ±13
2.5 in ±0.1 64 mm ±2.5
1/4 in ±0.03 6 mm ±1
0.01 in NA 0.25 mm NA
0.5 in NA 12.7 mm NA
17
ANSI A250.13-2014
Appendix B
(informative)
Example 1
Opening design pressure: per ASCE 7 = 67 psf, requires 350 ft-lb impact energy per local code.
Opening size: 3'0" x 7'0" — Single In-Swing
Wall type: 2 x 6 wood stud 16 in o.c. with 1/2 inch exterior sheathing — design pressure
rating 75 psf.
Frame: 16 ga. pressed steel with 5/8 inch stops.
Frame rating: for 3'0" x 7'0" with 1/4" x 3-1/2" lag screw anchors to wood studs at 24" o.c. = 75
psf. & 350 ft-lb — OK.
Hinges: (ABC Co. Model 1– 500 lbf – 350 ft-lb rating) 3 – 4" x 0.135" centered at 8" from
top, center of door and 8" from bottom.
Latch: (XYZ Co. Model 2 – 1000 lbf – 350 ft-lb rating for class II doors) single point
mortise, 5/8" throw.
Door: 3'0" x 7'0" Hollow Metal — Stiffness class II, 70 psf, 350 ft-lb rating. — OK.
Location Area (ft2) Load @ 70 psf (lbf)
A Top Hinge 3.125 219 < 500 OK.

B Middle Hinge 4.25 298 < 500 OK.
C Bottom Hinge 3.125 219 < 500 OK.
D Latch 10.5 735 < 1000 OK.
Opening Design Pressure Rating = 70 psf based on door.

Tested for Impact Energy Rating of 350 ft-lbf.
18
ANSI A250.13-2014
Example 2
Opening Design Pressure: Per ASCE 7 = 80 pounds per square foot (PSF), requires 350 ft-lbf impact
energy per local code.
Opening Size: 8'0" x 8'0" – Pairs of Doors
Wall Type: Masonry – design pressure rating 90 PSF – OK (Meets opening design pres-
sure requirement)
Frame: 14 ga. Pressed steel with 5/8 inch stops
Frame Rating: For a 8'0" x 8'0" with masonry T anchors is 80 PSF & 350 ft-lbf – OK (Meets
opening design pressure requirement)
Hinges: (ABC Co. Model 1 - 4" x 0.125", 300 lbf, 350 ft-lbf rating): 4 req’d per leaf - cen-
tered at 8" from top of door, centered at 34-2/3" from top of door, centered at
34-2/3" from bottom of door, & centered at 8" from bottom of door.
Latch: (XYZ Co. Model 2 – Surface Vertical rod exit device, 85 PSF, 350 ft-lbf impact
rating, two latchbolts per exit device per door leaf, 3/4" latch throw – OK (Meets
opening design pressure req.)
Door: 4'0" x 8'0" hollow metal – stiffness class I, 80 PSF & 350 ft-lbf Rating – OK
(Meets opening design pressure requirement)
21 1/3" A
26 2/3" B
8 FT E
26 2/3" C
21 1/3" D
24" 24"
4 FT
8 FT
Hinge Location / Area Calculation Load Calc Load vs Product Pressure vs Criteria
Door Area Rating Rating Met?
Top Hinge / A (21 1/3” x 24”)/144 = 3.555 ft2 80 PSF x 3.555 ft2 = 284 Lbf 284 Lbf < 300 Lbf N/A YES
Middle Upper Hinge / B (26 2/3” x 24”)/144 = 4.444 ft 2
80 PSF x 4.444 ft = 356 Lbf
2
356 Lbf > 300 Lbf N/A NO
Middle Upper Hinge / B (26 2/3” x 24”)/144 = 4.444 ft2 80 PSF x 4.444 ft2 = 356 Lbf 356 Lbf > 300 Lbf N/A NO
Bottom Hinge/ C (21 1/3” x 24”)/144 = 3.555 ft 2
80 PSF x 3.555 ft = 284 Lbf
2
284 Lbf < 300 Lbf N/A YES
Latches / D N/A N/A N/A 80 PSF < 85 PSF YES
Result: Opening does not meet the design pressure requirement due to hinge product
rating. In order to meet it, the hinges need to be replaced with higher load rated
hinges (≥ 300 Lbf).
19
ANSI A250.13-2014
Appendix C
(informative)
Door Component Impact Energy Research Project
Door Component Impact Energy Research Project
Intertek Testing Services has completed a study on the large missile impact test specified
by ASTM E1886/E1996 and its affects latches on in-swinging doors. The study was
conducted to quantify the energy that would tend to shear the latch bolt in fully assembly
tests and compare it to the energy delivered to the latch bolt in the ANSI A250.13
component test procedure which uses a relatively rigid fixture and a pendulum type
impactor.
Background
Since ANSI A250.13 was published, tests of single point (mortise and cylindrical) latches
have consistently produced failures in latches that have a history of acceptable
performance when tested in full assemblies. It has been clear that much of this difference
in results is due to the fact that, in assembly tests, only a fraction of the energy contained
in the impactor is actually delivered to the latch and bolt.
Just before the impact event, it is known that the impacting body represents about 350 ft-
lbs of kinetic energy. During the impact all this energy must be conserved. We know
that some energy is accounted for by several processes:
o Energy is absorbed by the door through deformation, bending, crushing

and/or tearing of the door materials.
o Energy is absorbed by deflection and movement of the assembly mass.
o Energy is absorbed and returned to the impactor (it bounces back).
o Energy is absorbed by deformation or crushing of the impactor striking
surface.
o Energy is absorbed in the mounting and supporting fixture and
construction.
o There are several other smaller areas of energy distribution, e.g. the sound
make by the impact.
The large and obvious disparity in results between full assembly impact tests and the
latch component test led to the design of an experiment that is described in this report as
a means of quantifying the energy distributed to the latch bolt in a typical door assembly.
Theory
Energy, when it causes movement or deformation, is termed ‘work’. If one strikes a
lump of lead with a hammer it will cause it to flatten and the ‘work’ thus done is a direct
result of the energy delivered by the hammer. Thus, by creating a test arrangement that
Door Component Impact Energy Research Project P ag e 1 of 8

30 May 2007
20
ANSI A250.13-2014
uses a material that will deform and retain its shape after an impact and making sure that
the energy is delivered through a consistent arrangement of striking surface, test body and
supporting surface the deformation of the test body provides and measurement of the
energy required to cause the deformation.
This deformation relationship to energy can be quantified by testing the same test body
material and form in a compression testing machine. As the machine loading platen
compresses and deforms the test body, the load increases. For any given point in
deformation, the area under the stress/strain curve can be integrated to determine the
work done on the test body and hence the equivalent amount of energy that would need to
be delivered in an impact event to cause the same deformation.
Procedure
The experiment was conducted in four phases.
Phase I was to use a 3’-0” by 7’-0” complete door assembly with a simulated latch bolt
and anvil assembly. The simulated latch bolt consisted of a 1.5” by ¾” steel bar securely
attached to the door and projecting 1.25” at the normal latch location. Immediately
behind the simulated latch bolt a heavy structural steel anvil was placed with a horizontal
gap of 1.57”. A solid lead test body was mounted on the anvil so that when the door was
struck by the impactor the energy absorbed in the latch area would result in deformation
of the lead test body. The lead test body was shaped in the form of a 4 sided pyramid
1.57 inches high with a square base with each side measuring 0.875”. After each impact
the height of the test body was measured and the deformation from its original height
determined. The impact was delivered to the door 6 inches from the latch edge centered
on the latch bolt location.
Phase II involved using the single point latch test fixture specified in ANSI A250.13 with
a simulated latch bolt and anvil set up as described above for the door test and the 100
pound pendulum impactor with a 2 x 4 by 12” long wood striking surface. The level of
impacts started as 350 foot pounds and was stepped down until the deformation of the
lead test body was approximately equal to that observed for the door assembly test in
phase I.
Phase III involved direct impact of the lead test body with the 9 pound 2 x 4 and air
canon as specified in ASTM E1886/E1996 except that a 3/16 thick steel plate was affixed
to the striking end of the 2 x 4 (overall weight was still 9 pounds). The pendulum
impactor was also used with a 350 ft-lbf impact to compare the energy delivered between
the two methods directly.
Phase IV was a series of compression tests of the lead test body using a universal testing
machine in order to determine the relationship between deformation and work or energy
required to produce specific levels of deformation.
Door Component Impact Energy Research Project Page 2 of 8

30 May 2007
21
ANSI A250.13-2014
Throughout these tests the deformation was determined by measuring the overall height
of the pyramidal test body before and after the test. The deformed height was determined
from the average of four measurements made at each of the four corners of the deformed
specimen.
Multiple trials where conducted where deemed necessary and it was found that the results
where repeatable to within 3-5% for all conditions of the tests.
Results
Chart 1. shows the relationship between test deformation of the lead test body used and
the load applied. Integration of the area under this curve for a given deformation
provides the value for ‘work’ required to produce the deformation observed.
Chart 1.
Deformation of Lead Test Body v. Load
2 x 4 Canon Direct
Impact
12,000 195.8 ft-lbf
11,000
Sample #1 Pendulum 350 ft-
10,000 lbf Direct Impact
9,000 Sample #2 144.1 ft-lbf
Recommended
8,000 Sample #3 Pendulum Impact
Load (lbf)
30 ft-lbf
7,000 ANSI A250.13
6,000 Component Impact
52.6 ft-lbf
5,000
2 x 4 Canon Impact
4,000 of door assembly
3,000 14 ft-lbf
2,000
1,000
0
0.000 0.100 0.200 0.300 0.400 0.500 0.600 0.700 0.800 0.900 1.000 1.100 1.200 1.300
Deformation (inches)
Chart 2 shows the relationship between the deformation and work for the specific test
body used. The relationship is approximated mathematically as:
Work = 120 x D3 (ft-lbf)

Where: D is the deformation in the test body in inches.
The R2 correlation coefficient is 0.99.

30 May 2007
22
ANSI A250.13-2014
Deformation v. Work for Lead Test Body
300
250
200
Work (ft-lbf)
Work
150
120 X^3
100
50
0
0 0.2 0.4 0.6 0.8 1 1.2 1.4
Deformation (inches)
Table 1. shows the results of phase I through III of this experiment.
Table 1.
Average Work Done

Number Average Impact on Test
of Deformation Energy Body
Test Condition Impactor Trials (inches) (ft-lbf) (ft-lbf)
20 Gauge Steel 9# 2 x 4 @
3 0.475 354 14.0
Stiffened Door 50 ft/s
Pendulum Direct 100# w/
5 1.083 350 144.1
to test body 12” 2 x 4
2 x 4 Cannon 9# 2 x 4 @
5 1.181 355.8 195.8
Direct to test body 50 ft/s
Pendulum w/ 100# w/
1 0.765 350 52.6
A250.13 Fixture 12” 2 x 4
Pendulum w/ 100# w/
1 0.677 150 37.2
A250.13 Fixture 12” 2 x 4
Pendulum w/ 100# w/
1 0.570 100 23.1
A250.13 Fixture 12” 2 x 4
Pendulum w/ 100# w/
2 0.535 75 19.4
A250.13 Fixture 12” 2 x 4
Pendulum w/ 100# w/
10 0.491 60 15.4
A250.13 Fixture 12” 2 x 4
Pendulum w/ 100# w/
2 0.440 50 11.4
A250.13 Fixture 12” 2 x 4

30 May 2007
23
ANSI A250.13-2014
Analysis
The results indicate that a surprising small amount of energy from the 350 foot-pound
impact of the 9 pound 2 x 4 is actually delivered to the latch in a full size door assembly
test. Only about 14 foot-pounds or 4% of the available energy needs to be withstood by a
typical latch bolt. In the case of the ANSI A250.13 fixture and pendulum impact at 350
ft-lbf, the energy delivered to the latch bolt is over 52 ft-lbf – about 15% of the available
energy and 3.7 times the energy delivered by the 2 x 4 impact in the full test assembly.
This confirms the observation that the small scale A250.13 test of latches is much more
severe than the assembly test with the 2 x 4 cannon.
Phase II indicates that, in the small scale test, a pendulum impact energy of 60 ft-lbf
results in approximately equivalent shearing energy delivery to that of the full scale
assembly test method.
It was observed that in the direct impact tests conducted in Phase III, the 2 x 4 cannon
procedure produced 51 ft-lbs (196 vs. 144 ft-lbf) or 35% greater work on the test body
than the pendulum. This is most likely due to the difference in velocity and the duration
of the actual impact event. The 2 x 4 moves at a velocity of 50 ft/sec up to the point of
impact whereas the pendulum velocity at impact is 15 ft/sec. This means that the 2 x 4
canon event takes place in about 4 milliseconds while the pendulum impact event takes
about 12 milliseconds or 3 times as long.
If the support structure where perfectly rigid (i.e. would not move or deflect at all) this
difference would not affect the energy transfer. However, in the real world, the
supporting structure is not perfectly rigid and therefore it absorbs some of the energy
delivered to it through movement and deflection. However, since the support is relatively
massive and is subject to inertia, the time involved in the impact event has a significant
influence on the outcome. Therefore the relatively shorter duration of the higher speed 2
x 4 impact allows less time for the support structure to absorb energy and hence a greater
proportion of the energy delivered ends up doing work on the test body.
An example of this effect can be seen at the target range. A high speed rifle bullet will
penetrate a ¼” thick suspended steel plate without noticeably moving it, but a 20 gauge
shotgun slug, with equivalent energy, but traveling much slower will not penetrate but
will cause a violent deflection of the same target.
Recommendations
This study has demonstrated that the small scale test specified in ANSI A250.13 for
latches is indeed much more severe than the exposure provided in door assembly tests
conducted per ASTM E1886/E1996 and similar wind borne debris impact tests. The
level of energy transmitted to the lockset should be reduced to a value closer to 15 ft-lbs.

30 May 2007
24
ANSI A250.13-2014
25
ANSI A250.13-2014
Appendix I
Experimental Design
ANSI A250.13 Latch Impact Test Energy Transfer Experiment

Problem: The simulated latch impact test using a rigid fixture and pendulum impactor
should deliver the same force and energy into the latch as occurs in an assembly when the
door is impacted by the 2 x 4 missile.
Experiment:
Principle: A given amount of energy delivered by a single impact will cause a specific
amount of deformation in a solid lead body such as a cylinder, pyramid or cone. Similar
deformation resulting from different methods of delivering the impact indicate similar
energy transfer.
Solid
Stop.
Lead Body
Steel
Stiffened ¾” x 1.5” Steel
Door Bar Simulated Latch
Bolt
h1 h2
Impact from 2 x 4
h1-h2 ≈ ε Cannon
First phase is to run a series of tests using a door and the set-up as shown above to
establish the effect of the standard test energy as transmitted to the test body.
Phase II - Once the level of deformation produced is established, the same test body will
be used in the latch impact fixture and the level of impact energy will be increased in
increments until the deformation of the test body equals that established in the first phase
of the experiment. Ten replicates will be performed at this level to establish the degree of
repeatability.

30 May 2007
26
ANSI A250.13-2014
Phase III will be direct impact of the test body with the 9 pound 2 x 4 at 50 feet per
second and with the 100 pound pendulum with the 3.5 foot drop height to evaluate the
relative direct energy transfer.
Phase IV will be to compression test the lead test body in a universal testing machine to
determine the work (or energy) required to produce a specific level of deformation.
The test bodies will be solid lead pyramids that produce a deformation of 25 to 75% of
the initial height at impacts within the range being studied.
1.57”
0.875”
Lead Test Body – 4- Sided Pyramid

30 May 2007
27
MEMBERS OF THE
Ceco
9159 Telecom Drive
ANSI/SDI A250.6 Recommended Practice for Hardware Reinforcing on Standard Steel Milan, TN 38358-3425
Doors and Frames (731) 686-8345
www.cecodoor.com
ANSI/SDI A250.8 Specifications for Standard Steel Doors and Frames (SDI-100)
Curries
1502 12th Street
SDI-128 Guidelines for Acoustical Performance of Standard Steel Doors and (641) 423-1334
www.curries.com
Frames
SDI-129 Hinge and Strike Spacing 931 S. Flores Street
SDI-133 Guidelines for Specifying Steel Doors & Frames for Blast Resistance San Antonio, TX 78204-1406
(210) 226-8271
www.deansteel.com
Test Procedures
Coatings for Steel Doors and Frames Fontana, CA 92336-1638
(909) 770-5700
HOLLOW METAL XPRESS
Surfaces for Steel Doors and Frames Phoenix, AZ 85043
(623) 936-7000
ANSI/SDI A250.13 Testing and Rating of Severe Windstorm Resistant Components for www.HMXpress.com
Mesker Door, LLc
(Not applicable for FEMA 320/361 or ICC-500 Shelters) 3440 Stanwood Boulevard
SDI-113 Standard Practice for Determining the Steady-State Thermal Huntsville, AL 35811-9021
Transmittance of Steel Door and Frame Assemblies (256) 851-6670
www.meskerdoor.com
MPI
(606) 523-0173
Carlstadt, NJ 07072
(201) 933-1900
SDI-122 Installation Troubleshooting Guide for Standard Steel Doors and www.pioneerindustries.com
155 Republic Drive
(731) 352-3383
SDI-112 Zinc-Coated (Galvanized/Galvannealed) Standard Steel Doors and www.republicdoor.com
Frames
SMP
SDI-117 Manufacturing Tolerances for Standard Steel Doors and Frames An ASSA ABLOY Door Group Company
5678 Concours Street
SDI-124 Maintenance of Standard Steel Doors & Frames Ontario, CA 91764
SDI-127 Industry Alert Series (A-L) (909) 593-2100
www.secmet.com
SDI-130 Electronic Hinge Preparations
Steelcraft
SDI-134 Glossary of Terms for Hollow Metal Doors and Frames 9017 Blue Ash Road
AUDIO-VISUAL PROGRAMS ALSO AVAILABLE (513) 745-6400
www.steelcraft.com

440.899.0010 • FAX 440.892.1404
7/11/2016 www.steeldoor.org

Fact File Compilation of SDI Technical D PDF

Uploaded by

Copyright:

Available Formats

Fact File Compilation of SDI Technical D PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Fact File Compilation of SDI Technical D PDF

Uploaded by

Copyright:

Available Formats

Fact File

Compilation of SDI Technical Documents and

Updated August 2016

Please visit www.steeldoor.org for the

Steel Door Institute

Summary of Documents Provides a description of each technical document

ANSI/SDI-100-91 See ANSI A250.8-03 (R2008)

SDI-105-98 See ANSI A250.11-2012

111-C Recommended Louver Details for Standard Steel Doors

SDI-124-16 Maintenance of Standard Steel Doors and Frames

SDI-127 Series - Industry Alerts (A through L)

SDI-127-A-06 (R14)* End Closure

SDI-127-D-06 Electric Strikes in Stud Walls

SDI-127-E-06 (R14)* Prime Painted Materials Alert

SDI-127-J-04 Back-Coating of Frames

SDI-127-K-09 (R14)* Improper Wedges as Hold-Opens

SDI-127-L-09 (R14)* Buyer Beware: Steel Doors with Lead-Based Primer

SDI-131-15 Accelerated Physical Endurance Test Procedure for Steel Doors

SDI-134-14 Glossary of Terms for Hollow Metal Doors and Frames

ANSI/SDI A250.6-2003 Recommended Practice for Hardware Reinforcing on Standard Steel

SDI-112 Zinc-Coated (Galvanized/Galvannealed) Standard Steel Doors and Frames

SDI-117 Manufacturing Tolerances for Standard Steel Doors and Frames

SDI-124 Maintenance of Standard Steel Doors and Frames

SDI-127 Series - Industry Alerts (A through L)

127-A End Closure

SDI-129 Hinge and Strike Spacing

SDI-130 Electrified Hinge Preparations

SDI-131 Accelerated Physical Endurance Test Procedure for Steel Doors

SDI-134 Glossary of Terms for Hollow Metal Doors and Frames

A250.8 Specifications for Standard Steel Doors and Frames (SDI-100)

A250.11 Recommended Erection Instructions for Steel Frames

STEEL DOOR INSTITUTE

Table 1 – Standard steel door grades and models

Standard Steel Door Levels Door Design Nomenclature

L LL V VL* N NL* G EG GL*

G2 G2L* G3 G3L* G4 G6 FG FG3 FL

* Note: Design combination is indicated by light followed by louver.

Nomenclature Letter Symbols

STEEL DOOR INSTITUTE

Standard Steel Doors

STEEL DOOR INSTITUTE

Standard Steel Doors and Frames

Wrap Around Frame

Opening & Door Opening Height 6' 8"

Wrap Around Frame

Modular Modular Modular

Throat 3TARTER#OURSE &INISH&LOOR'RID

Butt Type Frame

Modular Modular Modular

STEEL DOOR INSTITUTE

Recommended Details for

STEEL DOOR INSTITUTE

Door Opening Width

Center-Line Hinges Center-Line Lock Strike

Standard Frame Details

1" Gypsum Core 1-5/8" Steel or Wood

2-1/2" or 3-5/8" Steel Stud

Common Wall Conditions

2" Solid Plaster with 1/2"

Throat 3TARTER#OURSE &INISH&LOOR'RID

1VSQPTF 1FSGPSNBODF 3BUJOHT

± ",1˝ Figure F – Squareness