PiSector All in ONE

Wireless GSM Alarm System

User Manual (GSM-06)

Read manual fully before use.

PiSector Inc., USA, www.pisector.com

1. INTRODUCTION .......................................................................... 5
2. SYSTEM INITIALIZATION ........................................................... 8
3. SYSTEM SETTING INSTRUCTIONS .......................................... 9
3.1. ENTERING SETTING MODE ....................................................... 9
3.2. ADDING REMOTE CONTROLLER .............................................. 10
3.3. DELETING REMOTE CONTROLLER ........................................... 12
3.4. ADD SENSORS TO MAIN PANEL ................................................ 13
3.5. INSTALLATION OF DOOR SENSORS .......................................... 15
3.6. INSTALLATION OF W IRELESS PIR MOTION SENSORS ................. 16
3.7. DELETING DEFENSE ZONE ..................................................... 17
3.8. SETTING DEFENSE ZONE PLACES ........................................... 18
3.9. SETTING DEFENSE ZONE MODES ........................................... 19
3.10. SETTING DEFENSE ZONE SIREN ............................................. 20
3.11. ALARM DELAY SETTING ......................................................... 21
3.12. ADDING PHONE NUMBER ....................................................... 22
3.13. DELETING PHONE NUMBER .................................................... 23
3.14. ADDING SMS CELL PHONE NUMBER ...................................... 24
3.15. DELETING SMS CELL PHONE NUMBER ................................... 25
3.16. SET NET W ORK CENTER FUNCTION ........................................ 26
3.17. VOICE RECORDING ............................................................... 28
3.18. VOICE RECORDING REPLAY ................................................... 29
3.19. SETTING SYSTEM DATE ......................................................... 30
3.20. SETTING SYSTEM TIME .......................................................... 31
3.21. SCHEDULING TIMELY ARM ...................................................... 32
3.22. SCHEDULING TIMELY DISARM ................................................. 33
3.23. WIRELESS SIREN CODING ...................................................... 34
 3.24. WIRELESS SIREN CODE ENCRYPTION ..................................... 35
3.25. CHANGE OPERATION PASSWORD ............................................ 37
3.26. CHANGE PROGRAM PASSWORD.............................................. 38
3.27. SETTING ARM DELAY TIME ..................................................... 39
3.28. SETTING ALARM (CALL OUT) DELAY TIME ................................ 40
3.29. VOICE PROMPT SETTING ....................................................... 41
3.30. SIREN PROMPT SETTING FOR REMOTE CONTROLLER ............... 42
3.31. BACKLIGHT SETTING ............................................................. 43
3.32. SIREN SETTING IN “EMERGENCY” MODE .................................. 44
3.33. ARM / DISARM SMS NOTIFICATION ......................................... 45
3.34. LANGUAGE SETTING .............................................................. 46
3.35. SET MAX RING TIMES BEFORE ANSWERING ............................. 47
3.36. CHOICE MODE OF ALARM NETWORK ....................................... 48
3.37. FACTORY RESET ................................................................... 49
3.38. PASSWORD RESET ................................................................ 50
4. SYSTEM USAGE INSTRUCTIONS ........................................... 51
4.1. OUT ARM ............................................................................. 51
4.2. HOME ARM ........................................................................... 52
4.3. DISARM................................................................................ 52
4.4. ANSWER ALARM CALL ........................................................... 53
4.5. REMOTE CONTROL................................................................ 54
4.6. EMERGENCY ALARM CALL...................................................... 55
4.7. USE AS TELEPHONE .............................................................. 55
4.8. ALARM HISTORY REVIEW ....................................................... 56
5. TECHNICAL SPECIFICATIONS ................................................ 57
6. CARE AND MAINTENANCE ..................................................... 58
3
Main Features

Quad-band worldwide cellular phone (900/1800/850/1900 MHz).

Elegant touch keypad with easy to use detailed menu system.

128×64 lattice LCD screen with clock display (English/Chinese)

4 wired and 10 wireless (433MHz) defense zones; each wireless
zone supports up to 10 sensors.

Support for up to 8 remote controllers.

Built-in loud speaker and intelligent voice announcer.

Auto-play 10-second pre-recorded voice message on alarm
(useful for giving address/GPS position to emergency services).

Up to 6 phone numbers to dial out on alarm.

Up to 3 SMS numbers: to send SMS to when alarm.

Remote control by phone to arm, disarm, or intercom (listen-in).

One-touch control: ARM (out arm), STAY (home arm) via touch
keypad or arm and disarm via remote controller or telephone.

4 Arm Modes: out arm, home arm, delay arm and timely arm for
scheduling arm / disarm times).

8 Defense Zone Places: SOS, fire, gas, door, hall, window,
balcony, and boundary.

4 Arm Delay Modes: Real-time (immediate), 01-99 second delay,
24 hours (always-armed even if system disarmed), Disable

Alarm calls have priority over all other calls if the device is busy.

Direct wireless coding of any additional wireless accessories.

Alarm History to store the last 30 alarm records.

Arm via the main unit panel, remote controller, or remote call by
phone.

SMS alert of power failure and recovery.

Built-in Lithium-Ion battery with automatic recharge.

4
1. Introduction
Install battery to all door sensors

Open cover Install battery Close cover Keep both parts close

Install battery to IR motion sensor

Install batteries and keep them switched off.

Know Your System

2 1

1. LCD Screen: Resolution: 128×64; English and Chinese display.

2. LED Status Indicators

POWER: power and system activity indicator:
- fast flashing once per second: system is searching for GSM signal.
- slow flashing once per 3 seconds: system is in ready mode.
5
 SET: is ON when the system enters setting mode.
SIGNAL: wireless signal indicator (used by wireless sensors).
ALARM: is ON if any sensor triggers or sets off an alarm.

3. Touch Keypad: Resistive Touch Panel requires gentle key pressing.

Do not press the keypad heavily as this may reduce its sensitivity.
ARM: press to enter OUT ARM status (gives you 40 seconds to
leave home before system is armed).
STAY: press to enter HOME ARM status (deactivates all sensors
with Home defense zone mode and activates all other sensors).
CALL: For making phone calls. Enter the number you want to call,
and then press this CALL button. Press again to end call (hang up).
SOS: press to raise an emergency alarm.
ESC: clears the input content or back to last operation.
ENTER: confirms current command or operation.

5 6 7 8

6
4. Wired Port - Function interface of the main unit

1 T_VCC External keyboard power supply 12V

2 T_GND Ground External keyboard
3 A Connecting external keyboard A
4 B Connecting external keyboard B
5 GND Ground
6 Zone 1 Wired sensor 1: support both NO and NC
7 GND Ground
8 Zone 2 Wired sensor 2: support both NO and NC
9 GND Ground
10 Zone 3 Wired sensor 3: support both NO and NC
11 GND Ground
12 Zone 4 Wired sensor 4: support both NO and NC
13 GND Ground
14 G_ANT External antenna Ground
15 ANT External antenna

5. Internal Backup Battery Switch.

6. Power port for 12V 1.2AM adapter plug in

7. SP: Siren in for plug a external siren or wireless siren transmitter

8. Tel: Your exist telephone device connector port

LINE: Main telephone line connector jack

9. SIM Card Slot: Please pay attention to the direction arrow marked
on the slot: “LOCK” / “OPEN”. Do not insert or take out the SIM card
when the main unit panel is powered on.

7
2. System Initialization
Correct initialization of the main unit panel is important to its normal
working and lifespan.

1. Connect the wired accessories that you need.

2. Insert the SIM card.(NEVER insert SIM card during power on)

3. Connect the power adapter. The main unit panel will start
self-inspection and the POWER indicator LED will flash once per
second. If this LED does not light on, you need to restart the main
unit panel. Please do it at least 10 seconds later as repeated power
on and off in short times will shorten the service life of the system.

4. The POWER indicator will flash once every 3 seconds after finding
GSM network successfully. This is the normal system state.

5. Turn on the internal backup battery switch on the back of the main
unit panel.

6. Check the GSM signal icon on the LCD screen. Signal less than 3
bars will affect normal performance. Please place the main unit
panel at a place with good GSM signal reception.

8
3. System Setting Instructions
3.1. Entering Setting Mode
All settings have to be done in the setting mode.
Use keys 2 / 8 / 4 / 6 as direction keys (up / down / left / right).

At the disarm state, input your 6-digit password (default: 888888), then
press ENTER. The main unit panel will sound a beep and the SET
indicator lights on. The screen will display Remote Control menu.

Fig 1: disarm status Fig 2: please enter password

Fig 3: press ENTER to set

9
3.2. Adding Remote Controller
This system supports maximum 8 remote controllers ( 2 free remote
controllers come with PiSECTOR Alarm System package have been
coded). All extra remote controllers have to be coded with the main unit
panel in order to perform correctly. Their code cannot be empty or the
same as those already saved in the main unit panel.

Method: enter remote controller setting menu, press “4” or “6” to choose
remote controller serial number, press “8” to find “Coding” and then
press ENTER to confirm. Trigger the remote controller you want to add,
the main unit panel will make two beeps after receiving it. And then
press ENTER to confirm. If the remote controller has been saved before,
after triggering it, the main unit panel will make four beeps and LCD
screen display “Error, Repeated code”.

10
Operation figures:

Fig 1: enter remote control menu Fig 2: choose remote control serial
number and coding menu

Fig 4A: recognize successfully Fig 3: waiting to receive signal

Fig 4B: the main unit has the same code Fig 5: press ENTER to save
with remote controller code

11
3.3. Deleting Remote Controller
If the remote controller is lost or damaged, it must be deleted
immediately so no other person can control the main unit panel.

Method: enter remote controller setting menu, press “4” or “6” to choose
the remote controller you want to delete. Press “8” to find “Delete”, and
then press ENTER.

Operation figures:

Fig 2: choose the controller you Fig 1: enter remote controller setting
want to delete

Fig 3: press ENTER to confirm

12
3.4. Add Sensors to main panel
This alarm system supports 10 wireless defense zones, each of zone
supports up to 10 wireless sensors. All sensors and sirens in the
standard package have been coded to the main unit panel, you do not
need code/identify them again, if you want to add extra sensor late by
yourself, you need code it to the main panel in order to perform
correctly. The sensor cannot be the same as any of the saved sensors
in the main unit panel has a unique address.

Method: press key 888888(default password) then press enter, then

press “6” to choose zone menu, press enter you will see zone1 as Fig 2,
if you press "6" will get zone2. zone3.. you choice which zone you want
to code the sensor, then press “8” to find “Coding” then press ENTER to
confirm. you will see "000000000" as Fig 3, then trigger the sensor you
will see the sensor's address number as Fig 4A, then press ENTER to
save it as Fig 5. If the sensor has been saved before, after triggering it,
the main unit panel LCD screen will display “Error, Repeated code” as
Fig 4B.

13
Operation figures:

Fig 2: choose zone number and press Fig 1: enter defense zone setting
ENTER

Fig 4A: recognize successfully Fig 3: waiting signal from sensor

Fig 4B: the main unit has the same code Fig 5: press ENTER to save
with sensor code

14
3.5. Installation of Door Sensors
All door sensors which come from
PiSECTOR Alarm System standard
box have coded to main panel, you
do not need code them again.
Door sensor used for detecting the
status of open and close of windows
and doors. It will detect it and send
the signal to control panel.
a. Tear apart the double-side affix tape on the magnet and the
transmitter then affix them to the appropriate position. (stronger
recommend fix it again with super glue or screw to avoid it fall
down in floor.)
b. if the low-power indicator is on, please change the battery
Caution: Magnet should be close to near to the side of transmitter with
indicator. The two should align with each other and the distance should
not exceed 10mm.

15
3.6. Installation of Wireless PIR Motion Sensors
All Motion sensors which come
from PiSECTOR Alarm System
standard box have coded to main
panel, you do not need code
them again.
 PIR motion sensor are used to detect the movement within a
certain range.
 Fix the adjustment bracket on the wall with the provided
screws and attach the detector to the bracket, it is
recommended to mount at a height of 6.5ft to 7ft above the
floor
 Effect of the PIR motion sensor is best when the detection
direction is 90 degree angle with the walking direction of the
intruder. Choose the most suitable installation place and angle
according to actual situation and taking the following
installation diagram as reference to ensure the detection effect
is best
 Please do not fix it under direct sunlight or other strong lights
and also keep it away from places with frequent strong air
steam or air condition

 If the low-power indicator is on, please change the battery

16
3.7. Deleting Defense Zone
The wireless detector cannot trigger the main unit panel after it is
deleted.

Method: enter zone setting menu, press Enter, then press “4” or “6” to
choose the zone number which you want to delete, then Press “8” to
find “Delete”, and then press ENTER. Operation figures:

Fig 1: enter defense zone setting Fig 2: choose zone number

Fig 3: choose Delete and press ENTER

17
3.8. Setting Defense Zone Places
The location of defense zone can be set in the main unit panel, so that
the main unit panel can send detailed alarm messages. There are 8
locations for alarm: SOS, fire, gas, door, hall, window, balcony, and
boundary.

Please refer to “Chapter 6. Technical Parameters” for default settings.

Method: enter defense zone setting menu, press “4” or “6” to choose
the zone number, and then press “2” or “8” to enter zone place menu.
Press ENTER will shift the places.

Operation figures:

Fig 1: enter defense zone setting Fig 2: choose defense zone place

Fig 3: press ENTER to confirm

18
 Fig 4: (this example)
Before setting, the alarm SMS for zone 1 is: 01 zone fire alarm;
After setting, it is: 01 zone gas alarm.

The format of alarm SMS: [01~10] zone [place] alarm. For example,
you set the place of zone 4 as “Window”. The alarm SMS you receive is:
04 zone-B01(sensor number) window alarm.

3.9. Setting Defense Zone Modes

There are different defense zone modes: out arm, home arm, arm and
disarm mode. For example, if you need gas detectors working all the
time, then please set ARM, HOME, and DISARM all enabled.(Note:
Such as CO detector, smoke detector needs a independent zone, do
not set those detector with window/door sensor or motion sensor in one
zone, we advice user set motion sensors in one zone, window/door
sensors in other zone separate)

Method: enter defense zone setting menu, press “2” or “8” to choose
HOME arm status (enable or disable), press ENTER to confirm. Setting
methods for OUT arm and DISARM are the same.

Operation figures:

Fig 1: enter defense zone setting Fig 2: choose mode Fig 3: press ENTER to confirm

19
 Fig 4: (this example)
Before setting, zone 1 does not alarm in home arm status;
After setting, it will alarm when triggered in home arm status.

3.10. Setting Defense Zone Siren

The siren can be set on or off when there is an alarm for each defense
zone independently.

Method: enter defense zone setting, press “2” or “8” to choose siren
enable or disable, and then press ENTER to confirm.

Operation figures:

Fig 1: enter defense zone setting Fig 2: choose siren status Fig 3: press ENTER to confirm

Fig 4: (this example)

Before setting, the siren is on when zone 1 alarms;
After setting, siren will not sound when zone 1 alarms.

20
3.11. Alarm Delay Setting
Alarm delay: the main unit panel will make alarm call and the siren will
go off (if enabled for this zone) after a preset delay time.

Method: enter defense zone setting, press “2” or “8” to choose delay
enable or disable, and then press ENTER to confirm.

Operation figures:

Fig 1: enter defense zone setting Fig 2: choose delay status

Fig 3: press ENTER to confirm

Fig 4: (this example)

Before setting, the panel makes alarm and the siren rings immediately when zone
1 is triggered;
After setting, alarm will be after the preset time. (set the delay time under system
setting)

21
 3.12. Adding Phone Number
This system can store up to 6 phone numbers. When triggered, the
system will call out these numbers in order until someone answers the
call. The system will redial three times at most.

Without the approval and consent of relevant authorities, do not

set any of the dial out numbers to “911”, “112” or “999” or any
other emergency service provider.

Method: enter phone number setting menu, press “4” or “6” to choose
Phone1 or Phone2, Phone3....Phone6 and then press ENTER. Input
the number you want to set, then press ENTER to save.

Operation figures:

Fig 1: enter phone number setting Fig 2: choose serial NO. Fig 3: input phone number

Fig 4: press ENTER to save Fig 5: the 1st number is set successfully

22
3.13. Deleting Phone Number
Method: enter phone number setting, press “4” or “6” to choose serial
number, then press “8” to choose “Delete” and then press ENTER to
confirm.

Operation figures:

Fig 1: enter phone number setting menu Fig 2: choose the number you want to delete

Fig 3: choose “delete” Fig 4: the 1st number is deleted

23
3.14. Adding SMS Cell Phone Number
This system can store 3 SMS receiving cell phone numbers. When
alarming, it will send SMS to all these numbers.

Method: enter SMS number setting, press “4” or “6” to choose SMS 1 or
SMS 2 or SMS 3 and then press ENTER. Input the number you want to
set, then press ENTER to save.

Operation figures:

Fig 1: enter SMS number setting Fig 2: choose serial number and press
ENTER

Fig 3: input SMS receiving number Fig 4: press ENTER to save

24
3.15. Deleting SMS Cell Phone Number
Method: enter SMS number setting, press “4” or “6” to choose serial
number, then press “8” to choose “Delete” and then press ENTER to
confirm.

Operation figures:

Fig 1: enter SMS number setting Fig 2: choose the number you want to
delete

Fig 3: choose “delete” Fig 4: the 1st number is deleted

25
3.16. Set Net Work Center Function
The network function of community shall be supported by the monitor
center, the protocol of monitor center shall be compatible with the
system’s protocol, otherwise the networking may not work. This system
supports phone center and SMS network center. If you need to use the
network function, please contact us. The setting of network function
includes center phone numbers, user IDs, and other parameters.
Set center phone number: enter the Network Centers menu, and the
Phone Center menu, and then press ENTER key to enter setting status.
Input the phone center number and save it. The detailed operation
diagram is as follows:

Diagram1: Enter Network Centers Diagram2: Choose Phone center menu,

menu and then confirm.

Diagram3: Input center phone number Diagram3: Input center phone number

Set user ID: enter the Network Centers menu, and the Phone Center
menu. Press Key 6 to move right to choose the User ID menu and
26
press Enter. Input the user ID, press Save key to save it.
The detailed operation diagram is as follows:

Diagram1: Enter Network Centers Diagram2: Choose user ID and

menu confirm.

Diagram3: Input user ID Diagram4: Save the user ID

Upload system arming/disarming report to the network center: enter

Network centers menu, and then enter the Phone Center menu. Press
Key 6 to move right to choose the Arm Report menu, and press ENTER
key to enable/disable this function.

27
 The detailed operation diagram is as follows:
Diagram1: Enter Network centers Diagram2: Choose Arm report menu
menu

Diagram3: Choose to enable/disable

the function of arm report

3.17. Voice Recording

This system can make 10-second voice recording for user to give out
instructions to emergency services when the system is triggered.

Method: enter record setting, and start by choosing “Start recording”

and immediately start recording your voice message. The system will
stop recoding after 10 seconds.

Operation figures:

Fig 1: enter record setting Fig 2: start recording Fig 3: record for 10 seconds

28
3.18. Voice Recording Replay
Enter Recording setting, and then press “6” to choose “Play”. The main
unit panel will start playing the voice message you have recorded. You
can re-record until you are satisfied with the message.

Operation figures:

Fig 1: enter record setting Fig 2: you’ll see this menu

Fig 4: press ENTER to play the Fig 3: press “6” to choose “play”

record

29
3.19. Setting System Date
The date format is MM/DD/YY. (“YY” setting is from 00-99)

Method: enter “Time” menu, and then choose “Date”. Input the exact
date you want to set and press ENTER to confirm.

Operation figures:

Fig 1: enter time setting menu Fig 2: choose date setting menu

Fig 3: input the date Fig 4: press ENTER to save

30
3.20. Setting System Time
Time in this alarm system is 24-hour system. Enter “Time” menu, you
will see “Date” menu, then press “6” to choose “Time”. Input the exact
time you want to set and press ENTER to confirm.

Operation figures:

Fig 1: enter time setting menu

Fig 2: you’ll see date setting menu Fig 3: press “6” to choose “time”

Fig 4: input the time Fig 5: press ENTER to save

31
3.21. Scheduling Timely Arm
This feature is also called Timely Arm. After setting the required arm
start time, the alarm system will arm itself at the pre-set time.
(Note: disable the timely arm, just set time over 24hours, e.g. 24:03 ,
this function will disable)

Method: enter “Time” menu, you will see “Date” menu, then press “6” to
choose “Timely arm”. Input the exact time you want to start the arming
period and press ENTER to confirm.

Operation figures:

Fig 1: enter time setting menu Fig 2: you’ll see date setting menu

Fig 4: input the time you want to set Fig 3: press “6” to choose “timely arm”

32
3.22. Scheduling Timely Disarm
This feature is also called Timely Disarm. After setting the required
disarm start time, the alarm system will disarm itself at the pre-set
time.(Note: disable the timely disarm, just set time over 24hours, e.g.
24:03 , this function will disable)

Method: enter “Time” menu, you will see “Date” menu, then press “6” to
choose “Timely arm”. Input the exact time you want to start the
disarming period and press ENTER to confirm.

Operation figures:

Fig 1: enter time setting menu Fig 2: you’ll see date setting menu

Fig 3: press “6” to choose “timely disarm”

Fig 4: input the time you want to set

33
3.23. Wireless Siren Coding
If you want to add a extra wireless siren to the main unit panel, you
need code/identify the siren to main panel in order to work correctly.
( Main panel have build -in a transmitter for wireless siren, the wireless
siren which come from PiSECTOR ALARM SYSTEM BOX has coded
with Main panel, customer just place the siren to where you like inside
house or outside house, and connect the 12V 0.5A power adapter to a
wall out plug, if you armed the main panel and trigger a sensor, siren
will goes off )

Method: set the wireless siren that you need to code in coding status.
Then enter “Wireless Control” menu on the main unit panel, you will see
“Control” menu. Press “6” to choose “Wireless siren” setting, and then
enter “Transmission” setting. The main unit panel will send a wireless
signal to the siren.

Operation figures:

Fig 1: enter Wireless Control menu Fig2: control menu

34
 Fig3: Press “6” to choose Wireless
siren

Fig 4: After pressing ENTER key, the main unit will transmit a wireless signal to
control the wireless siren.

3.24. Wireless Siren Code Encryption

The alarm signal code used with the wireless siren is sent from the
internal transmitter of the main unit panel. The code of this signal is the
same for all wireless alarm systems produced by PiSector Inc. If you
and your neighbor are using the same model, the alarm signal from
your neighbor may cause your siren to sound off too. It is therefore
recommended that you encrypt the wireless siren to avoid interference
(or use external transmitter).

Method: enter “Wireless Control” menu, and then “Control” menu. Press
“6” to choose “Wireless siren”, then press “8” to choose “Encryption”.
Input 4 numbers randomly and then save it.

35
Operation figures:

Fig 1: enter wireless control menu Fig 2: control menu

Fig 3: press “6” to choose wireless siren Fig 4: input 4 numbers randomly

Fig 5: press ENTER to save

36
3.25. Change Operation Password
The operation password is used for daily use of the system (disarm or
remote control). The default operation password is 1234.

Method: Enter “Settings” menu, and then “Operate password”. Input the
4-digit password you want to set, and save it.

Operation figures:

Fig 1: enter settings menu Fig 2: enter operate password menu

Fig 3: input the 4-digit password Fig 4: save it

37
3.26. Change Program Password
The program password is used for system setup (default is 888888).

Method: Enter “Settings” menu, and then “Operate password”, press “6”
to choose “Program password”. Input the 6-digit password you want to
set, and save it.

Operation figures:

Fig 1: enter settings menu Fig 2: you’ll see “Operate password”

menu

Fig 3: press “6” to choose program Fig 4: input password and save it
password

38
3.27. Setting Arm Delay Time
After setting, the system will enter OUT ARM status after the preset
delay time. Delay time ranges from 01-99 seconds. The system default
time is 60 seconds.

Method: Enter “Settings” menu, then you will see “Operate password”.
Press “6” to choose “Delay arm”. Input the time you want to set and
save it.

Operation figures:

Fig 2: you’ll see “Operate password”

Fig 1: enter settings menu
menu

Fig 3: press “6” to choose “delay arm” Fig 4: input time and save it

39
3.28. Setting Alarm (Call Out) Delay Time
After setting, when there is an alarm, the system will call out after the
preset delay time. Delay time ranges from 01-99 seconds. The system
default time is 60 seconds.

Method: Enter “Settings” menu, then you will see “Operate password”.
Press “6” to choose “Delay alarm”. Input the time you want to set and
save it.

Operation figures:

Fig 1: enter settings menu Fig 2: you’ll see operate password menu

Fig 3: press “6” to choose “delay alarm” Fig 4: input time and save it

40
3.29. Voice Prompt Setting
The main unit panel has voice prompt feature. For example when user
press arm or disarm on the remote controller, it will give voice prompt.
The system default for the voice prompt is on. Users can disable or
enable it according to actual need.

Method: Enter “Settings” menu, then you will see “Operate password”.
Press “6” to choose “Voice prompt” and choose “Enable” or “Disable”.

Operation figures:

Fig 1: enter settings menu Fig 2: you’ll see operate password menu

Fig 3: press “6” to choose “voice prompt” Fig 4: choose enable/ disable

41
3.30. Siren Prompt Setting for Remote Controller
If enabled, the siren will sound a short beep each time you press the
remote controller. System default is disabled.

Method: Enter “Settings” menu, and then you will see “Operate
password”. Press “6” to choose “Siren prompt” and choose “Enable” or
“Disable”.

Operation figures:

Fig 1: enter settings menu Fig 2: you’ll see operate password menu

Fig 3: press “6” to choose “siren prompt” Fig 4: choose enable/ disable

42
3.31. Backlight Setting
The backlight of the LCD screen and keypad will be off automatically
after a certain period of time when there is no operation on the keys.
Users can set it keep on if required. System default is disabled.

Method: Enter “Settings” menu, and then you will see “Operate
password”. Press “6” to choose “Backlight on” and choose “Enable” or
“Disable”.

Operation figures:

Fig 1: enter settings menu Fig 2: you’ll see operate password menu

Fig 3: press “6” to choose “backlight on” Fig 4: choose enable/ disable

43
3.32. Siren Setting in “Emergency” Mode
When you press the emergency button of the remote controller, the
siren does not normally sound as this feature is disabled by default.
Users can enable/disable according to the actual need.

Method: Enter “Settings” menu, and then you will see “Operate
password”. Press “6” to choose “Remote siren” and choose “Enable” or
“Disable”.

Operation figures:

Fig 1: enter settings menu Fig 2: you’ll see operate password menu

Fig 3: press “6” to choose “remote siren” Fig 4: choose enable/ disable

44
3.33. Arm / Disarm SMS Notification
When a user arms or disarms the system, other users can be notified
automatically via SMS notifications to all SMS numbers. The SMS
message content will be one of the following arm modes:

Out arm | System armed | Out disarm | System disarmed.

Method: Enter “Settings” menu, and then you will see “Operate
password”. Press “6” to choose “Arm disarm SMS” and choose
“Enable” or “Disable”.

Operation figures:

Fig 1: enter settings menu Fig 2: you’ll see operate password menu

Fig 3: press “6” to choose “arm Fig 4: choose enable/ disable

disarm SMS”

45
3.34. Language Setting
This alarm system supports English and Chinese languages. Please
enter the “Settings” menu, and you will see “Operate password”. Press
“6” to choose “Language”. Press ENTER to switch between languages.

Operation figures:

Fig 1: enter settings menu

Fig 2: you’ll see operate password menu

Fig 3: press “6” to choose “language” Fig 4: choose the version you need

46
 3.35. Set Max Ring Times Before Answering
Call the main panel, after the ringing circle, the main panel will active
automatically. then you can remote control the alarm system follow
prompt.
Operate: enter settings menu, press ENTER, enter operate password,
then you will see Line Rings, enter a number which you want to system
active after how many rings

Diagram1: Enter Settings menu Diagram2: Enter Operate password

menu

Diagram3: Press Key 6 to enter line

Diagram3: Press Key 6 to enter line
rings menu
rings menu

47
 3.36. Choice Mode of Alarm Network
Sets the system alarm network, the system can select phone line
alarm, Or GSM line alarm, or telephone line + GSM line alarm.
Method: entre into setup mode, press ENTER, enter operator
password 1234, then press 6 to choose the alarm mode menu to
decide the choice alarm network.

Diagram1: Enter Settings Diagram2: Enter Operate Diagram3: Press Key 6 to

menu password menu enter alarm mode menu

48
3.37. Factory Reset
If the system ever becomes unstable or if you need to change cellular
network, it is recommended to make a full factory reset of the system.

Enter “Settings” menu, and then you will see “Operate password”.
Press “6” to choose “Factory setting”. After this operation, all the
settings will be restored to factory defaults and all sensors and sirens
have to be re-coded too.

Operation figures:

Fig 1: enter settings menu Fig 2: you’ll see operate password menu

Fig3: press “6” to choose “factory setting” Fig 4: Press ENTER to confirm

49
3.38. Password Reset
If users forget the password, they can input 95175308246 in disarm
status to retrieve it. The main unit panel will display “Please wait, Back
to default password”. After this operation, the operate password will be
reset back to factory setting “1234” and program password to “888888”.

Operation figures:

Fig 1: under disarm status Fig 2: input 95175308246

Fig 3: confirm the operation

50
4. System Usage Instructions
4.1. Out Arm
Out arm means all the defense zones are in arm status. When there is
nobody at home, it is recommended to arm the system with all
detectors enabled. If any detector is triggered (by intruder, fire, gas
leakage, water leak, etc.), the system will make alarm calls and SMS
notification.

Use the main unit panel keypad to press [ARM]. You will hear 60 beeps
(one per second) and then the screen will display “System armed”.

Remote controller operation: press arm button [ ] on the remote

controller.

Main unit panel operation: press [ARM]. The system will enter arm
status after the delay time (default: 60 seconds)

51
4.2. Home Arm
Home arm means part of the defense zones are in arm status. When
there is someone at home, it is recommended, for safety purpose, to
enable some of the detectors (such as sensors for door, window,
balcony, etc), and disable the others (such as sensors for the hall or
some places easy to be triggered by person at home).

Remote controller: press home arm button [ ] on the remote controller.

Main unit panel: press [STAY].

4.3. Disarm
The purpose of disarming the system is to disable all sensors except
those set to 24-hour Arm Delay Mode. It can be used while the
system is armed or while the system is in alarm state.

Use the main unit panel keypad to input user password + #. The screen
will display “System disarmed”.

Remote controller: press disarm button [ ] on the remote controller.

Main unit panel: password + ENTER

52
4.4. Answer Alarm Call
When the main unit panel sounds an alarm, it will dial the preset
numbers. If no one answers the call, the system will call the next
number automatically. If someone answers the call, they will hear your
10-sceond pre-recorded voice message. Then can then interact with
system via their telephone keypad.

If they hang up immediately without answering the call, the system will
continue cycling through the preset numbers for three times at most.
Press [*]: Listen to the alarm information.

Press [1]: Main unit panel stops alarming and Arm; it stops calling
users.

Press [2]: Main unit panel stops alarming and Disarm; it stops calling
users.
Press [3]: Siren off and monitors the scene for 30 seconds; for
continued monitoring, press [3] again to monitor for another 30
seconds.

Press [4]: Main unit panel starts a 30-second two-way intercom. It

cannot be controlled by the mobile during the time of intercom.

53
4.5. Remote Control
Dial the number of the main unit panel by phone, and after 1 ring, you
will hear a voice prompt “Please enter password”. If the password is
correct, you will then hear a voice prompt “Please enter instruction"
then you can press 1 to arm, Press 2 to disarm, Press 3 to monitor,
or Press 4 to intercom. If the password is incorrect, you will hear a
prompt voice “Wrong password, please re-enter”.

The system default operate password is 1234. Make sure to enter the
password firmly by pressing and holding one digit at a time so you can
hear a beep for each key press. You may need to hold keys for half a
second at a time.

Press [1]: arm, if finished successfully, you will hear a voice prompt
“System armed”.

Press [2]: disarm, if finished successfully, you will hear a voice prompt
“System disarmed”.

Press [3]: monitoring for 30 seconds, to continue monitoring, press [3]

again for another 30 seconds. You can cancel monitoring at anytime by
pressing [1] to arm and [2] to disarm.

Press [4]: two-way intercom for 30 seconds. You cannot operate the
main unit panel during this time. You can cancel intercom at anytime by
pressing [1] to arm and [2] to disarm.

54
4.6. Emergency Alarm Call
Sometimes, there may be some accidents happening (such as sudden
illness of old people or children, fire accident, burglar intrusion). Press
[SOS] button on keypad, or [ ] button on remote controller or wireless
panic button, the main unit panel will alarm and make call to the preset
user numbers.

Remote controller operation: press [ ] button on the remote controller.

Main unit panel operation: press [SOS].

The SMS content for emergency help is: 00 zone SOS alarm.

4.7. Use as Telephone

In disarmed state, you can use the main unit panel to make any call just
like a normal telephone. Dial telephone number on keypad, press
[CALL] button and the main unit panel will make a beep and the LCD
screen will display the number you are calling. After the call, press
[CALL] button again to hang up and the main unit panel will go back to
disarmed state.

55
4.8. Alarm History Review
This alarm system can store 30 alarm records. The last alarm is ranked
as the first record. And when the record number exceeds 30, the oldest
record will be overwritten automatically.

Method: In disarmed state, input [00] + ENTER, the main unit panel
enters the state of Alarm record. Press “4” or “6” to upturn or downturn,
and press “Exit” to exit checking.

Fig 1: press 00 in disarm status Fig 2: press 4 or 6 to check

Fig 3: press 4 or 6 to check

56
5. Technical Specifications

Input Voltage DC12V/1A

Standby Current < 35mA

Alarming Current < 450mA

Wireless Frequency 433MHz, PT2262/EV1527, 4.7MΩ

GSM Frequency 900 / 1800 / 850 / 1900 MHz

Backup Battery NI-HI AAA*6 DC 7.2V

Siren Volume < 110dB

Out Home Alarm

Defense Zone Type Siren
Arm Arm Information

Zone 1 effective invalid real-time Door alarm yes

Zone 2 effective invalid real-time Hall alarm yes

Zone 3 effective effective real-time Window alarm yes

Zone 4 effective effective real-time Balcony alarm yes

Zone 5 effective effective 24 hours Fire alarm yes

Zone 6 effective effective 24 hours Gas alarm yes

Emergency button effective effective 24 hours SOS alarm no

Zone 7-10 effective invalid real-time SOS alarm yes

（ 7-10）
Wired zone（ ） effective invalid real-time SOS alarm yes

Program Password 888888 Remote control On

Operate password 1234 Siren Off

Siren sound time 180 sec. Home Appliance Optional

57
6. Care and Maintenance
This wireless alarm system has an excellent design and uses advanced
sensitive electronics that require care and dust-free environment. The
following suggestions are required to maintain your obligations under
the warranty terms, and for prolonging the service life of the system:

 Place the main unit panel and all accessories out of children reach.
 Keep the alarm system dry. rain, humidity and various fluids or
moisture all will corrupt the electronic circuitry.
 Do not use or place the alarm system in dirty locations, otherwise
the electronic elements will be damaged.
 Do no place the system in excessively hot locations. High
temperature will shorten the service life of electronic equipment,
damage batteries, deform or even melt some plastic parts.
 Do not place the system in excessively cold locations. Otherwise
condensation many occur and damage the circuit board of the
alarm system.

It is recommended that you check and test the alarm system

periodically:
Check the main unit panel every three months:
1. Whether it can arm/disarm normally;
2. Whether it can dial the number for alarm normally;
3. Whether it can receive wireless signals from detectors
normally;
4. Whether the back-up battery is self-recharging normally.
58
 Check the wireless detectors once a month:
1. Trigger wireless detectors to ensure that the system can alarm
normally;
2. Check all detector/sensor batteries to ensure that the all have
good voltage levels;
3. Check whether wireless detectors can send signal to the main
unit panel normally.

Check the SIM card:

1. Check the SIM card network signal, credit balance, etc.
2. Make sure the PIN code verification of the SIM card is
disabled.
3. Keep the password and SIM card number safe to prevent
others from remote controlling the system without permission.
 Since the alarm system is continuously in operation or standby
mode, the power supply adapter for the main unit panel shall be
connected to a safe and reliable mains outlet.
 Do not place the system near your bedroom or office desk, because
the siren will make very high-pitch sound in case of alarm, which
may adversely affect your rest, work, health or your unborn baby.
 If the alarm system will not be used for a long time, disconnect it
from the power supply.
 Do not disassemble, repair or alter the product without permission,
or it may cause accidents or fire. PiSector Inc. is NOT responsible
for any consequences whatsoever rising from such unauthorized
actions.
59
 Do not drop the product on the ground or on hard surfaces, as it
may lead to intermittent malfunctions and/or system damage or
total failure.
 Without the approval and consent of relevant authorities, do
not set any of the dial out numbers to “911”, “112” or “999” or
any other emergency service provider.

Read the suggestions above carefully as they are required to maintain

your obligations under the warranty terms, and for prolonging the
service life of the system and follow the instructions therein. If any
equipment does not work as specified, contact PiSector Inc.
[[email protected]] or your local authorized sales agent.

TAMPERING WITH THE EQUIPMENT IN ANY WAY

WILL AUTOMATICALLY VOID YOUR WARRANTY

60
The following sensors are optional and packed separately

Choose according to your specific needs

61
 π
3.1415926535897932384626433832795028841971
693993751058209749445923078164062862089986
280348253421170679821480865132823066470938
446095505822317253594081284811174502841027
019385211055596446229489549303819644288109
756659334461284756482337867831652712019091
456485669234603486104543266482133936072602
491412737245870066063155881748815209209628
292540917153643678925903600113305305488204
665213841469519415116094330572703657595919
530921861173819326117931051185480744623799
627495673518857527248912279381830119491298
336733624406566430860213949463952247371907
021798609437027705392171762931767523846748
184676694051320005681271452635608277857713
427577896091736371787214684409012249534301
465495853710507922796892589235420199561121
290219608640344181598136297747713099605187
072113499999983729780499510597317328160963
185950244594553469083026425223082533446850
352619311881710100031378387528865875332083
814206171776691473035982534904287554687311
595628638823537875937519577818577805321712
268066130019278766111959092164201989380952
572010654858632788659361533818279682303019
520353018529689957736225994138912497217752
834791315155748572424541506959508295331168
6172785588907509838175463746493 Sector.com

62