Analog & Digital Electronics: Course No: PH-218 Lec-4: Clampers, Voltage Multipliers, & Zener Diode

Analog & Digital Electronics
Course No: PH-218
Lec-4: Clampers, Voltage multipliers, & Zener diode
Course Instructors:
Dr. A. P. VAJPEYI
Department of Physics,
Indian Institute of Technology Guwahati, India 1
Clampers:
Clamping is a process of introducing a dc level into a signal.
Clamper circuit consist of diode and capacitor that shifts the input waveform to
different dc level without changing the appearance of the applied waveform.
When the diode is forward biased, it will

conduct and charge the capacitor. The output
voltage across the diode is zero (0.7V).
The capacitor is charged to peak input

voltage quickly because of small time
constant of the circuit.
2
During the –ve cycle when diode is reverse bias, the diode becomes to its
off state. In this case, the output voltage equals to the sum of the input
voltage and the voltage across the terminals of the capacitor which have the
same polarity with each other
During positive half cycle
During negative half cycle
3
During 0 to t1, the input voltage is negative, diode is forward biased and
conducts so Vo is zero and the capacitor is charged to –10 V with the
polarity as shown.
During t1 to t2, diode becomes reverse biased and open circuit and at t2,
when Vi is 10V total voltage change is 20V.
4
During negative half cycle:
Diode will be forward biased and Capacitor will be charged by 15V.
Applying KVL: Vin+Vc+Vsupply =0

-10V+Vc+5V=0 ; Vc = 5V
During positive half cycle:
Diode will be reverse biased and diode will be open circuit.

Applying KVL: : Vin+Vc+Vsupply =0
10V+5-Vo=0 ; Vo = 15V
5
Voltage Multipliers:
Voltage multipliers are the circuit which provide a dc output that is
multiple of the peak input ac voltage.
Voltage doubler will provide a dc output that is twice the peak input ac
voltage and voltage tripler will provide a dc output that is three times the
peak input ac voltage.
The basic idea in voltage multiplier circuit is to charge each capacitor to

the peak input ac voltage and to arrange the capacitor so that their stored
voltages will add.
Voltage doubler:
6
Voltage doubler:
During the positive half cycle, diode D1 is forward biased and diode D2 is
reverse biased, that will charge capacitor C1 to peak value of input voltage.
During the negative half cycle, diode D2 is forward biased and diode D1 is
reverse biased, that will charge capacitor C2 to the twice the peak value of
input voltage because capacitor C1 ( charged to Vp) and input voltage (Vp )
now act as series aiding voltage source.
When input voltage returns to its original polarity, diode D2 is again reverse
biased (off), and then the capacitor C2 will be discharged through the load RL
The time constant (RLC2) is so adjusted that C2 has little time to loose any
of its charge before the input polarity reverses again.
During the negative half cycle, diode D2 is turned on , capacitor C2 will be

recharged again until voltage across it is again equal to 2Vp.
7
Voltage Multipliers:
Voltage Tripler
Voltage Quadrupler
8
Zener diode:
A zener diode is a special type of diode that is designed to operate in the

reverse breakdown region.
A properly doped (heavily doped) junction diode which has a sharp

breakdown voltage is known as zener diode.
Heavy doping causes a very thin depletion layer which results in sharp
breakdown voltage.
A zener diode is always connected in reverse bias mode.
The use of a sufficiently strong electric field at the junction can cause a
direct rupture of the bond. If the electric field exerts a strong force on a bound
electron, the electron can be torn from the covalent bond thus causing the
number of electron-hole pair combinations to multiply. This mechanism is
called Zener breakdown.
9
Zener diode as a voltage regulator:
The zener diode operated in the breakdown

region have a constant voltage regardless the
value of the current through the device, that
allows zener diode to be used as a voltage
regulator.
Voltage stabilizer circuit that maintain a

constant voltage across the load when the
source voltage or the load current vary,
shown below.
10
Zener diode as a voltage regulator:
First calculate the thevenin voltage

across the zener diode.
Zener will work in the breakdown region

only if the Thevenin voltage across zener is
more than VZ
If zener is operating in breakdown region, the current through RS is given by
IL is load current and Is is total current. Is = IL + Iz
11
Ripple factor of diode rectifier:
The effectiveness of a rectifier depends upon the magnitude of ac
component in the output; smaller the ac component, the more effective is the
rectifier.
Ripple factor is a measure of effectiveness of a rectifier circuit and

defined as a ratio of rms value of ac component to the dc component in
the rectifier output.
I ac
Ripplefactor =
I dc
2
I ac I rms
I rms = I dc2 + I ac2 = 2
−1
I dc I dc
12
Ripple factor of diode rectifier:
Im Im
For half wave rectifier:
I rms = I dc =
2 Π
Ripple factor = 1.21
For full wave rectifier:

Im 2I m
I rms = I dc =
2 Π
Ripple factor = 0.48

PIV diode full wave rectifier:
14
PIV full wave Bridge rectifier:
15

Analog & Digital Electronics: Course No: PH-218 Lec-4: Clampers, Voltage Multipliers, & Zener Diode

Uploaded by

Copyright:

Available Formats

Analog & Digital Electronics: Course No: PH-218 Lec-4: Clampers, Voltage Multipliers, & Zener Diode

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Analog & Digital Electronics: Course No: PH-218 Lec-4: Clampers, Voltage Multipliers, & Zener Diode

Uploaded by

Copyright:

Available Formats

Analog & Digital Electronics

Course No: PH-218

Lec-4: Clampers, Voltage multipliers, & Zener diode

When the diode is forward biased, it will

The capacitor is charged to peak input

During positive half cycle

During negative half cycle

Applying KVL: Vin+Vc+Vsupply =0

Diode will be reverse biased and diode will be open circuit.

The basic idea in voltage multiplier circuit is to charge each capacitor to

During the negative half cycle, diode D2 is turned on , capacitor C2 will be

A zener diode is a special type of diode that is designed to operate in the

A properly doped (heavily doped) junction diode which has a sharp

A zener diode is always connected in reverse bias mode.

The zener diode operated in the breakdown

Voltage stabilizer circuit that maintain a

First calculate the thevenin voltage

Zener will work in the breakdown region

IL is load current and Is is total current. Is = IL + Iz

Ripple factor is a measure of effectiveness of a rectifier circuit and

Ripple factor = 1.21

For full wave rectifier:

Ripple factor = 0.48

You might also like