1

CONTENTS
QUICK REFERENCE GUIDE
PLEASE READ INSTRUCTIONS
FOR USE BOOKLET!
PROGRAMME CHART
PREPARING THE LAUNDRY
SELECTING A PROGRAMME AND OPTIONS
STARTING AND COMPLETING A PROGRAMME
CHANGING A PROGRAMME
INTERRUPTING A PROGRAMME
DAILY MAINTENANCE AND CLEANING

INSTRUCTIONS FOR USE

BOOKLET
BEFORE USING THE DRYER Page 3
PRECAUTIONS AND GENERAL
RECOMMENDATIONS Page 5
ELECTRICAL CONNECTION Page 7
DESCRIPTION OF THE DRYER Page 8
REMINDER - MAINTENANCE AND CLEANING Page 8
CLEANING THE LINT FILTER Page 8
CLEANING THE HEAT EXCHANGER Page 9
DRAINAGE SYSTEM Page 10
DOOR REVERSIBILITY Page 11
TROUBLESHOOTING GUIDE/
AFTER-SALES SERVICE Page 12

2
BEFORE USING THE DRYER
• This dryer is exclusively designed to dry machine • Small indoor located storage rooms, bathrooms,
dryable laundry in quantities which are usual for toilets, shower rooms and enclosed areas without
private households. ventilation are not suitable locations for installation of
• Observe the instructions given in these Instructions For the dryer. If it must be installed in such a location,
Use and the Programme Chart before using the dryer. adequate ventilation must be ensured (open doors,
• Keep the Instructions For Use and the Programme ventilation grid or slot larger than 500 cm²).
Chart handy for reference. If you pass on the dryer to • Before running the first cycle, ensure that the water
others, make sure that the Instructions For Use and container is fully pushed inside and that the heat
exchanger is correctly positioned.
the Programme Chart go with it.
• The manufacturer declines all liability for damage to
property or injury to persons or animals due to non-
compliance with the directions given in these
Instructions For Use.
1. Removing the packaging and inspection
• After unpacking, make sure that the dryer is
undamaged. If in doubt, do not use it. Contact the
After-Sales Service or your local retailer. • Before running the first cycle, ensure that all of the
• If the appliance was exposed to the cold prior to drainage system hoses are connected (as shown in
delivery, keep it at room temperature for a few hours the picture below).
before operating.
• Do not operate the dryer if it has been damaged
during transport. Contact one of our After-Sales
Service technicians.
2. Electrical Connections
• Electrical connections must be carried out by a
qualified technician in compliance with the
manufacturer’s instructions and current standard
safety regulations.
• Electrical connections must comply with local
Electricity Board regulations.
• Data regarding voltage, power consumption and the
required fuse protection is shown on the rating plate
mounted at the rear of the dryer.
• The dryer must be earthed as prescribed by law.
• Before carrying out any maintenance on the dryer
• If possible use a hose to drain the water directly into
disconnect it from the mains supply. the domestic plumbing system. This will avoid having
• Mains cable replacement must only be carried out by to empty the water container at the end of each
the After-Sales Service. drying cycle, since the condensation water can be
• After installation, access to the mains plug or to an all- directly drained away. Also see section entitled
pole disconnection switch must be ensured at all times. “Drainage System”.
• Light bulb replacement must only be carried out by • Take care not to install the dryer on a deep-pile carpet.
the After-Sales Service. • Take care not to trap the mains cable between the
dryer and the wall.
3. Installation
• When installing the dryer make sure that the four feet
• Do not install your dryer where it may be exposed to
are stable and resting on the floor, adjusting them as
extreme conditions, such as: poor ventilation, required, and check that the machine is perfectly
temperature below 5°C or above 35°C. level using a spirit level.
• The appliance must not be installed behind a lockable • If, due to lack of space, the dryer must be installed
door, a sliding door or a door with hinges on the directly next to a gas or coal stove, a heat insulating
opposite side to that of the tumble dryer, in such a plate (85 x 57cm) must be installed in between and
way as to prevent the tumble dryer door from being the side of the plate facing the stove must be covered
fully opened. with aluminium foil.

3
• The dryer is not designed for built-in installation. D. Secure both distance holders by turning them in a
• The dryer can be installed under a worktop, clockwise direction as far as the stop position.
provided that adequate ventilation of the dryer is
assured. Install a ventilation grid (minimum 45 cm x 8
cm), in the rear part of the worktop under which the
dryer is installed.

5. User and child protection

• Children must not be allowed to play with the dryer.
• Ensure that children and small animals cannot get into
the drum.
• Keep the packaging materials (plastic bags,
4. Assembly of distance holders polystyrene parts, etc.) out of reach of children, as
they are potentially dangerous.
To ensure that the appliance is positioned at a correct
distance from the wall at the rear side and to allow • The appliance is not intended for use by persons
sufficient ventilation, distance holders must be mounted (including children) with reduced physical, sensory or
on the rear side of the dryer before starting the first mental capabilities, or lack of experience and
drying cycle. knowledge, unless they have been given supervision
A. Remove the two distance holders from the packaging. or instruction concerning use of the appliance by a
B. The distance holders must be inserted on the rear person responsible for their safety. Children should
side of the dryer in the protective cover. be supervised to ensure that they do not play with
the appliance.

Stacking kit
• Depending on the
model, your dryer can
be stacked on top of
your front loading
washing machine. For
further information
please contact the
After-Sales Service.

B
C. Insert the distance holders in the holes provided on
both sides.

4
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
• Always set the programme/time selector knob to the
To minimise the risk of fire in the tumble dryer, “0” position after use. This prevents the dryer from
the following precautions should be observed: being switched on accidentally.
• Oil-soaked items ignite spontaneously, especially • Before cleaning or carrying out maintenance, switch off
when exposed to heat sources such as in a tumble the dryer and disconnect it from the mains supply.
dryer. The items become warm, causing an oxidation
• To clean the outside of the dryer, use a neutral
reaction in the oil. Oxidation creates heat. If the heat
detergent and a damp cloth.
cannot escape, the item can become hot enough to
catch fire. Piling, stacking or storing oil-soaked items • Do not use abrasive detergents.
can prevent heat from escaping and so create a fire • The final phase of a drying cycle always occurs
hazard. without heat (cool-down phase) so that the items are
• Do not dry unwashed items in the tumble dryer. left at a temperature which ensures that they will not
be damaged.
• Ensure that the appliance is maintained as shown in
the section “Maintenance and cleaning”. • Wipe away any lint from the door seal and the door
using a damp cloth.
• Ensure that the appliance is installed as per the
instructions above. • If the lint filter mesh is clogged, clean it with water
and a soft brush.
• Items that have been soiled with substances such as
cooking oil, acetone, alcohol, petrol, kerosene, spot • Since lint can penetrate through the filter, it is
removers, turpentine, waxes and wax removers necessary to clean the entire filter area (including
must be washed in hot water with an extra amount below the filter) from time to time using a brush, a
of detergent before being dried in the tumble dryer. damp cloth or a vacuum cleaner.

• Do not use flammable cleaning agents. EC Declaration of Conformity

• Do not use the tumble dryer if chemicals have been • This dryer has been designed, constructed and
used for cleaning. distributed in compliance with the safety
• Items such as foam rubber (latex foam), shower caps, requirements of EC Directives:
waterproof textiles, rubber backed articles and • 2006/95/EC Low Voltage Directive
clothes or pillows fitted with foam rubber pads must
• 2004/108/EC Electromagnetic Compatibility
not be dried in the tumble dryer.
Directive
• Fabric softeners or similar products should be used
as specified in the fabric softener instructions.
• Remove all objects from pockets, such as lighters and • This appliance is marked according to the European
matches. directive 2002/96/EC on Waste Electrical and
• Never use or store flammable materials near to the Electronic Equipment (WEEE).
dryer. • By ensuring that this product is disposed of correctly,
• Never stop a tumble dryer before the end of the you will help prevent potential negative
drying cycle, unless all items are quickly removed and consequences for the environment and human
spread out so that the heat is dissipated. health, which could otherwise be caused by
inappropriate waste handling of this product.
• Warning: rear panel may be hot.
• The dryer is suitable for indoor use only.
• Do not use extension leads or multiple adaptors.

5
Packaging • Always set the program selector knob to the “0”
• The packaging box is 100% recyclable, as confirmed position after the end of the cycle.
by the recycling symbol.

Disposing of packaging and old appliances

• The dryer is built from reusable materials. The dryer
must be disposed of in compliance with local waste
disposal regulations.
• Before scrapping cut off the power cable so that the
dryer cannot be connected to the mains.

• The symbol on the product or on the

documents accompanying the product indicates that
this appliance must not be treated as household
waste. Instead it should be handed over to the
applicable collection point for the recycling of
electrical and electronic equipment. Disposal must
be carried out in accordance with local
environmental regulations for waste disposal.
• For more detailed information about treatment,
recovery and recycling of this product please contact
your local city council office, your household waste
disposal service or the shop where you purchased
the product.

Energy saving tips

• Always dry a full load, depending on the type of
laundry and the programme/drying time. For more
detailed information, see the programme chart.
• By preference use the maximum spin speed allowed by
your washing machine, since draining the water
mechanically requires less energy. You will save time
and energy when running your drying cycle.
• Do not overdry the laundry.
• Clean the lint filter after every drying cycle.
• Clean the heat exchanger every month.
• Place your dryer in a room with a temperature
between 15°C and 20°C. If the temperature is higher
then ventilate the room, e.g. by opening the window.
• Always select the correct programme/drying time for
the load in order to obtain the desired drying results.
• Select the ‘Gentle’ option only in case of drying small
loads.
• When drying cotton, for example, dry Iron Dry and
Cupboard Dry loads together. Start with the Iron Dry
programme/drying time setting, remove the laundry to
be ironed at the end of that cycle and dry the remainder
of the load on the Cupboard Dry setting.

6
ELECTRICAL CONNECTION

1) For United Kingdom only

Warning - this appliance must be earthed
Fuse replacement
If the mains lead of this appliance is fitted with a BS 1363A 13amp
fused plug, to change a fuse in this type of plug use an ASTA marked
fuse, approved to BS 1362 and proceed as follows:
1. Remove the fuse cover (A) and fuse (B).
2. Fit replacement 13A fuse into fuse cover.
3. Refit both into plug.

Important:
The fuse cover must be refitted when changing a fuse. If the fuse cover
is lost, the plug must not be used until a correct replacement is fitted.
Correct replacements are identified by the colour insert or by the
colour embossed in words on the base of the plug.
Replacement fuse covers are available from your local electrical store.

2) For the Republic of Ireland only

The information given in respect of United Kingdom will frequently
apply, but a third type of plug and socket is also used, the
2-pin type with side earth terminal.

3) Socket outlet / plug (valid for both countries)

If the fitted plug is not suitable for your socket outlet, please contact
Whirlpool Service for further instructions. Please do not attempt to
change the plug yourself. This procedure must be carried out by a
qualified Whirlpool technician in compliance with the manufacturer’s
instructions and current safety regulations.

7
DESCRIPTION OF THE DRYER
A. Work top
B. Water container
C. Contact pin
D. Door:
To open the door, pull the handle.
To close the door, push gently until closed.
E. Filter
F. Heat exchanger
G. Heat exchanger flap

REMINDER - MAINTENANCE AND CLEANING

Before cleaning or carrying out maintenance, switch off the dryer.

AFTER EACH DRYING CYCLE

• Clean the lint filter at the end of every drying cycle.
• Empty the water container at the end of each drying
cycle.

EACH MONTH
• Clean the heat exchanger at least every month (see
“Cleaning the heat exchanger” on the next page).

CLEANING THE LINT FILTER

Depending on the model of your dryer, the lint filter can
have different shapes.
Clean the lint filter after every drying cycle, or when the
lint filter indicator lamp lights up, proceeding as follows:

A. Take the lint filter out of the dryer and carefully open
the filter.
A A
B. Carefully remove the complete lint from the lint
screen.

When the lint filter is clean, put it back into the dryer.
Make sure that the lint filter is correctly positioned before
starting the next drying cycle.

B B

8
CLEANING THE HEAT EXCHANGER
Before cleaning or carrying out maintenance, switch off the dryer.
Clean the heat exchanger at least every month, or whenever the heat exchanger indicator lamp
lights up (optional feature, depending on the model of your dryer), proceeding as follows.
A. Open the heat exchanger flap and put it to one side.

B. Turn the two locking bars at the side of the heat exchanger towards the
middle, to the horizontal position, and pull the heat exchanger out.

C. Hold the heat exchanger as shown in the picture. Clean it under running
water by turning it around to reach all sides, especially in front and behind.
Wipe away dust and lint from the heat exchanger seals and plates.
Clean the inside of the heat exchanger plates under running water, from
the front side to the back.

D. Remove the lint from the heat exchanger housing by hand or with a
damp cloth. Clean the entire housing from the back to the front side,
ensuring that all lint is removed.

• Fully insert the heat exchanger back into the housing (TOP or HAUT mark
upwards) and lock it again by turning the locking bars back to their original position.
• The heat exchanger does not need to be dry when it is reinserted after cleaning.
• Insert and latch the flap again. The flap can only be closed if the heat
exchanger is correctly positioned.
• The heat exchanger indicator lamp will switch off automatically when
you start the next drying cycle.
The heat exchanger aluminium plates may become discoloured over time,
depending on the model of your dryer.

9
DRAINAGE SYSTEM
For your convenience: C. Connect the hose to the sewage system. The height
The dryer can be connected directly to the sewage difference between the floor where the dryer is
system of the house to avoid having to empty the positioned and the sewage system connection should
water container after each drying cycle. not exceed 1 m.
Place an absorbent cloth underneath to collect water
spillage.
A. Unplug the hose located at the upper rear part of the
dryer.

Notice: To prevent water siphoning back into the

appliance, the end of the hose must not be immersed in
the drain water. Avoid bending and twisting the hose.

A
B. Remove the hose from the rear protective cover.

10
DOOR REVERSIBILITY

For your convenience:

A
In case you want to stack the dryer on a washing machine, you can
reverse the door opening direction, to lower the position of the door
handle.
Unplug the dryer.

A. Open the door.

B. Using a spanner, turn the contact pin (B) in the top part of the door
through 90° and pull it out. B

C. Remove the door lock: C

Unscrew the 2 screws above and below the door lock system.

D. Press the small knob above the door lock system with a small
screwdriver, move the door lock slightly upwards and pull the door lock
towards you with your finger.

E. Reverse the door:

Remove the two screws of the door fixing plate. Fasten the door again
on the desired side with the 2 screws. Take care to tighten the screws
horizontally to avoid pinching off the door seal.
Reposition the door lock:
Insert the door lock on the opposite side of the door fixing plate. Press
it fully into the hole and move it downward slightly, until the small knob
of the door lock system latches in position. Fasten the two screws
above and below the door lock system. E
Now reinsert the contact pin on the inside of the door, at the top, by
inserting it and turning it again through 90°.

NOTE: Ideally you should use a Torx T20 type screwdriver to undo
and tighten the screws.

11
TROUBLESHOOTING GUIDE/
AFTER-SALES SERVICE
In the event that the dryer malfunctions, one of the following failure codes may be displayed.
Depending on the model of your dryer, the failure may be displayed in letters or by different
blinking LEDs.

Failure code LED failure code Check to be carried out by customer before service call

F01 Please call the After-Sales Service.

F02 Please call the After-Sales Service.

F03 Please call the After-Sales Service.

F04 Please call the After-Sales Service.

Turn the dryer OFF and unplug it. Make sure that the ambient temperature is
F05 between 5°C and 35°C. Wait for 1 hour. Plug the dryer back in and restart it. If the
failure reoccurs, please call the After-Sales Service.

Turn the dryer OFF and unplug it. Make sure that the ambient temperature is
F06 between 5°C and 35°C. Wait for 1 hour. Plug the dryer back in and restart it. If the
failure reoccurs, please call the After-Sales Service.

F07 Please call the After-Sales Service.

Turn the dryer OFF and unplug it. Wait for 5 minutes. Plug the dryer back in and restart it. If the failure reoccurs,
F10 - 15 please call the After-Sales Service.
Turn the dryer OFF and unplug it. Wait for 1 hour. Plug the dryer back in and restart it. If the failure reoccurs,
F18 please call the After-Sales Service.
Turn the dryer OFF and unplug it. Wait for 5 minutes. Plug the dryer back in and restart it. If the failure reoccurs,
F19 please call the After-Sales Service.
Turn the dryer OFF and unplug it. Wait for 1 hour. Plug the dryer back in and restart it. If the failure reoccurs,
F20 please call the After-Sales Service.
Turn the dryer OFF and unplug it. Wait for 5 minutes. Plug the dryer back in and restart it. If the failure reoccurs,
F21 please call the After-Sales Service.
Turn the dryer OFF and unplug it. Wait for 5 minutes. Plug the dryer back in and restart it. If the failure reoccurs,
F22 please call the After-Sales Service.
Start LED blinks
2 times per Make sure that the door is correctly closed and the heat exchanger correctly positioned. If the failure reoccurs,
second when please call the After-Sales Service.
pressed
Heat exchanger
LED blinks 2 Make sure that the heat exchanger is correctly positioned. If the failure reoccurs, please call the After-Sales
times when Start Service.
button is pressed

LED not blinking LED blinking

12
TROUBLESHOOTING GUIDE/
AFTER-SALES SERVICE
If a fault occurs, before contacting our After- After-Sales Service
Sales Service, perform the following checks to
try to remedy the problem: If, after carrying out the above checks, the
malfunction persists or reoccurs, turn the
Drying takes too long / laundry is not dry dryer off and call the After-Sales Service
enough: (refer to warranty).
• Correct programme selected?
• Laundry too wet (Washing machine spin speed less Please specify:
than 1000 rpm? When the spin speed is less than • The nature of the fault.
1000 rpm a water container fault may occur during • The dryer type and model.
the drying cycle). • The service code (the number after the word Service
• Lint filter clogged (filter indicator lamp on?) on the adhesive rating plate) on the lower side of the
• Heat exchanger clogged? (refer to the sections door opening.
“CLEANING THE LINT FILTER/CLEANING THE • Your full address and phone number.
HEAT EXCHANGER”).
• Is the ambient temperature too high?
• END indicator lamps on? The drying cycle is
complete and the laundry can be taken out.
• ‘Gentle’ option selected? The ‘Gentle’ option should
only be selected with small loads.
• Mixed laundry load (for example cotton and
synthetics).

The dryer does not operate:

(after a power failure and/or interruption to the
mains supply, always press the “Start (Pause)”
button).
• Plug connector properly inserted into the mains
electricity socket?
• Power failure?
• Fuse blown?
• Door properly closed?
• Drying programme selected?
• Start delay option selected?
• “Start (Pause)” button activated?
• Indicator lamps are lighting up?

Lint filter, water container or heat exchanger

indicator lamp on:
• Lint filter clean?
• Water container empty?
• Water container correctly positioned?
• Heat exchanger clean and correctly positioned?

Water droplets underneath the dryer:

• Heat exchanger correctly positioned?
• All lint on the heat exchanger seal removed?
• All lint on the door seal removed?
• Water container positioned correctly?
• Dryer levelled?

13