Ivar Aasen Field Development Project – pdQ

01 21/05/2014 Issued for Review YEL RAJ LUM

Prepared Reviewed Approved

Rev. Date Reason for Issue
by by by

PORTABLE WATER TANK CALUCLATION

(53TB001 A/B/C)

Package Title:

Area System Project Tag Numbers: No. of

Code: Code: 53TB001A/B/C Pages:
M320 42 37

Project No.: Supplier Document Number: Rev.

xxxxxxx XXXXXXXXXXX 01
Purchase Order No: Project Document Number: Proj Rev.
C-00011
XXXXXXXXXXXXXXXXXXX XX
 CONTENT PAGE

1 DESIGN DATA 1

3 WALL DESIGN 2

5 STIFFENER PROPERTIES 7

7 NOZZLES & OPENING 12

9 WIND LOADING 14

11 WEIGHT SUMMARY 15

13 TRANSPORTATION LOAD 16

15 SESMIC LOAD 17

17 BLAST LOAD 18

19 LOAD AT BASE 19

21 LEG DESIGN 20

23 LEG BASE PLATE DESIGN 21

25 LIFTING LUG DESIGN CALCULATION 22

DESIGN DATA

DESCRIPTION :
TAG NO. : 42TB00L7
MANUFAC'S. SERIAL NO : -
DIMENSION ( mm ) : 900 mm (W) x 1400 mm (L) x 3000 mm (H)
DESIGN CODE : API 650 + ROARK'S FORMULA
CODE STAMPED : -
THIRD PARTY : -

PROPERTIES UNIT DATA

CAPACITY m3 3.5

CONTENT - VARIOUS CHEMICAL

FLUID SPECIFIC GRAVITY - 1.00

DESIGN PRESSURE bar g LIQUID HEAD + 0.07

o
DESIGN TEMPERATURE, C 50

HYDROSTATIC TEST PRESSURE bar g FULL OF WATER

IMPACT TEST - NO

RADIOGRAPHY - 10%

CORROSION ALLOWANCE mm in 0.0 0.00

ROARK'S FORMULA

SIDE WALL DESIGN

ITEM NAME : 42TB00L7

Tank Height, H = 118.11 in 3000 mm

Tank Width, W = 35.43 in 900 mm
Tank Length, L = 55.12 in 1400 mm

Design Pressure = FULL WATER + 0.07 bar g

o
Design Temp. = 50 C
Material = TITANIUM GRADE 2

As per Table 26 Case No.1a Chapter 10 of Roark's

Rectangular plate, all edges simply supported, with uniform loads over entire plate.
S
For Section , A (Worst Case)
g = 9.81 m/s2 a
ρwater = 1000 kg/m3
S b S
a = 18.39 in 467.0 mm
b = 39.37 in 1000.0 mm
a/b = 0.4670 S
β = 0.0947 Loading q= ρwater gH + ρwater gh Pa
2
α= 0.0052 = 29430 + 7000 N/m
γ= 0.3707 = 4.2674 + 1.0150 psi
Ε= 1.52E+07 psi = 5.2824 psi
t= 0.3150 in 8.0 mm
c.a = 0.0000 in 0 mm
t (corr) = 0.3150 in 8.0 mm

At Center,
Maximum Deflection, α 4)/Et3
= -(αqb
= -3.50
= 3.50 mm < t/2 then O.K

Maximum Bending stress, σ = (βqb2)/ t2

= 7819 psi < σallowable 31302 psi. then OK

Material TITANIUM GRADE 2

Yield Stress, σy = 47427 psi
Stress Ratio, σ/σy = 0.165

At center of long side,

Maximum reaction force per unit length normal to the plate surface,

R = γ qb
= 77.09 lb/in
= 8710.72 N/mm
ROARK'S FORMULA

SIDE WALL DESIGN

ITEM NAME : 42TB00L7

Tank Height, H = 118.11 in 3000 mm

Tank Width, W = 35.43 in 900 mm
Tank Length, L = 55.12 in 1400 mm

Design Pressure = FULL WATER + 0.07 bar g

o
Design Temp. = 50 C
Material = TITANIUM GRADE 2

As per Table 26 Case No.1a Chapter 10 of Roark's

Rectangular plate, all edges simply supported, with uniform loads over entire plate.
S
For Section , B (Worst Case)
g = 9.81 m/s2 a
ρwater = 1000 kg/m3
S b S
a = 17.72 in 450.0 mm
b = 39.37 in 1000.0 mm
a/b = 0.4500 S
β = 0.0882 Loading q= ρwater gH + ρwater gh Pa
2
α= 0.0039 = 29430 + 7000 N/m
γ= 0.3688 = 4.2674 + 1.0150 psi
Ε= 1.52E+07 psi = 5.2824 psi
t= 0.3150 in 8.0 mm
c.a = 0.0000 in 0 mm
t (corr) = 0.3150 in 8.0 mm

At Center,
Maximum Deflection, α 4)/Et3
= -(αqb
= -2.61
= 2.61 mm < t/2 then O.K

Maximum Bending stress, σ = (βqb2)/ t2

= 7280 psi < σallowable 31302 psi. then OK

Material TITANINUM GRADE 2

Yield Stress, σy = 47427 psi
Stress Ratio, σ/σy = 0.153

At center of long side,

Maximum reaction force per unit length normal to the plate surface,

R = γ qb
= 76.69 lb/in
= 8664.79 N/mm
STIFFENER CALCULATION
For Horizontal
Maximum bending moment occurs at the point where dM/dx = 0 and shear force is zero,
that is, at the middle of the beam.

Stiffener No. 1 (typical)

L= 467 mm = 18.39 in
207.97 lb/in ґ= 1000 mm = 39.4 in
Load q = 5.2824 psi
unit load W = q x ґ psi
= 207.97 lb/in

FB 50 x 6
X
4
I = 0.5848 in
18.39 in
Wa Wb

Bending Moment
As per Table 8.1 Case 2e of Roark's (Uniform load on entire span)
At x = L/2 = 9.19 in
2
Maximum moment, Mmax = WL /8
= 8788 lb-in

M/I = σ/y

(I/y)required = M/σ
3
= 0.533 in
Use FB 50 x 6
I/y = 1.516 in3 > (I/y)required then O.K

Therefore, σ = 5795 psi < σallowable 16500 psi. then O.K

Deflection
As per Table 8.1 Case 2e of Roark's (Uniform load on entire span)

At x =L/2= 9.19 in
4
δmax = (5WL )
384EI

= 0.035 < L/360 = 0.0511 in. then O.K

Therefore the size used is adequate.

STIFFENER CALCULATION
For Vertical

Stiffener No. 1 (typical)

L= 1000 mm = 39.37 in
97.12 lb/in ґ= 467 mm = 18.4 in
Load q = 5.2824 psi
unit load W = qxґ psi
= 97.12 lb/in

FB 50 x 6
X
I = 0.5848 in4
39.37 in
Wa Wb

Bending Moment
As per Table 8.1 Case 2d of Roark's (Uniformly increasing load)
At x = 0.548L = 21.57 in
Maximum moment, Mmax = 0.0215WL2
= 3237 lb-in

M/I = σ/y

(I/y)required = M/σ
3
= 0.196 in
Use FB 50 x 6
I/y = 1.516 in3 > (I/y)required then O.K

Therefore, σ = 2134 psi < σallowable 16500 psi. then O.K

Deflection
As per Table 8.1 Case 2d of Roark's (Uniformly increasing load)

At x = 0.525L = 20.67 in

δmax = 0.001309WL4
EI

= 0.0344 < L/360 = 0.1094 in. then O.K

Therefore the size used is adequate.

STIFFENER CALCULATION
For Horizontal
Maximum bending moment occurs at the point where dM/dx = 0 and shear force is zero,
that is, at the middle of the beam.

Stiffener No. 1 (typical)

L= 450 mm = 17.72 in
207.97 lb/in ґ= 1000 mm = 39.4 in
Load q = 5.2824 psi
unit load W = q x ґ psi
= 207.97 lb/in

FB 50 x 6
X
4
I = 0.5848 in
17.72 in
Wa Wb

Bending Moment
As per Table 8.1 Case 2e of Roark's (Uniform load on entire span)
At x = L/2 = 8.86 in
2
Maximum moment, Mmax = WL /8
= 8159 lb-in

M/I = σ/y

(I/y)required = M/σ
3
= 0.495 in
Use FB 50 x 6
I/y = 1.516 in3 > (I/y)required then O.K

Therefore, σ = 5381 psi < σallowable 16500 psi. then O.K

Deflection
As per Table 8.1 Case 2e of Roark's (Uniform load on entire span)

At x =L/2= 8.86 in
4
δmax = (5WL )
384EI

= 0.030 < L/360 = 0.0492 in. then O.K

Therefore the size used is adequate.

STIFFENER CALCULATION
For Vertical

Stiffener No. 1 (typical)

L= 1000 mm = 39.37 in
93.58 lb/in ґ= 450 mm = 17.7 in
Load q = 5.2824 psi
unit load W = qxґ psi
= 93.58 lb/in

FB 50 x 6
X
I = 0.5848 in4
39.37 in
Wa Wb

Bending Moment
As per Table 8.1 Case 2d of Roark's (Uniformly increasing load)
At x = 0.548L = 21.57 in
Maximum moment, Mmax = 0.0215WL2
= 3119 lb-in

M/I = σ/y

(I/y)required = M/σ
3
= 0.189 in
Use FB 50 x 6
I/y = 1.516 in3 > (I/y)required then O.K

Therefore, σ = 2057 psi < σallowable 16500 psi. then O.K

Deflection
As per Table 8.1 Case 2d of Roark's (Uniformly increasing load)

At x = 0.525L = 20.67 in

δmax = 0.001309WL4
EI

= 0.0331 < L/360 = 0.1094 in. then O.K

Therefore the size used is adequate.

ROARK'S FORMULA

BOTTOM PLATE DESIGN

ITEM NAME : 53TB001A/B/C

Tank Height, H 133.9 in 3400 mm

Tank Width, W 98.43 in 2500 mm
Tank Length, L 137.80 in 3500 mm

Design Pressure = FULL WATER + 0.07 BARG

o
Design Temp. = 50 C
Material = SS316L

As per Table 26 Case No.1a Chapter 10 of Roark's

Assume rectangular plate, all edges simply supported, with uniform loads over entire plate
S
For Section , Each Section (Largest area)
g= 9.81 m/s2 a
ρwater = 1000 kg/m3
S b S
a= 27.56 in 700 mm
b= 23.62 in 600 mm
a/b = 1.1667 S
β= 0.3614 Loading q= ρwater gh + 0.07 BARG
α= 0.0587 = 33354 + 7000 N/m2
γ= 0.4492 = 4.8363 + 1.0150 psi
Ε= 2.90E+07 = 5.8513 psi
t= 0.3150 in 8.0 mm
c.a = 0.0000 in 0 `
t (corr) = 0.3150 in 8.0 mm

At Center,
Maximum Deflection, α 4)/Et3
= -(αqb
= -3.00
= 3.00 mm < t/2 then O.K

Maximum Bending stress, σ = (βqb2)/ t2

= 11895 psi < σallowable 13926 psi. then OK

Material SS316L
Yield Stress, σy = 21100 psi
Stress Ratio, σ/σy = 0.564

At center of long side,

Maximum reaction force per unit length normal to the plate surface,

R = γ qb
= 62.08 lb/in
STIFFENER CALCULATION (at Bottom Plate)
For Short Beam
Maximum bending moment occurs at the point where dM/dx = 0 and shear force is zero,
that is, at the middle of the beam.

L= 700 mm = 27.56 in
138.22 lb/in ґ= 600 mm = 23.6 in
Load q = 5.8513 psi
unit load W = q x ґ psi
= 138.22 lb/in

FB 50 x 6
X
4
I = 0.591 in
27.56 in
Wa Wb

Maximum bending moment,

At x = L/2 = 13.78 in
Mmax = WL 2/8
= 13122 lb-in

M/I = σ/y

(I/y)required = M/σ
3
= 0.249 in
Use FB 50 x 6
I/y = 1.582 in3 > (I/y)required then O.K

Therefore, σ = 8296 psi < σallowable 52668 psi. then OK

Maximum Deflection at Center of Beam

At x = L/2 = 13.78 in

δmax = (5WL4)
384EI

= 0.0641 < L/360 = 0.0861 in. then O.K

Therefore the size used is adequate.

ROARK'S FORMULA

ROOF CALCULATION

ITEM NAME : 53TB001A/B/C

Assume rectangular plate, all edges simply supported, with uniform loads over entire plate
S

a Live load, LL = 0.2846 psi

Roof weight = 1203.724 lb
S b S Structure weight = 0 lb
Concentrated weight = 661 lb
Total dead load,TDL = 0.0927 psi
S
Total conc. load, CL = 0.0488 psi

Tank Width, W 98.43 in 2500 mm

Tank Length, L 137.80 in 3500 mm
g= 9.81 m/s2
3
ρwater = 1000 kg/m
a= 68.90 in 1750.0 mm
b = 49.21 in 1250.0 mm
a/b = 1.4000
β = 0.2874
α = 0.0444 Loading q = LL + CL + TDL
γ = 0.4200 = 0.426 psi
Ε= 2.90E+07
t = 0.314961 in 8.0 mm
c.a = 0 1.52E+07 mm
t (corr) = 0.314961 in 8.0 mm

At Center,
Maximum Deflection, = -(αqb4)/Et3 All. Deflection =3500/300= 11.67 (max) mm
= -3.11 mm
= 3.11 mm < All. Deflection. O.K = 11.67

Maximum Bending stress, σ = (βqb2)/ t2

= 2989 psi < σallowable 13926 psi then OK

Material SS316L
Yield Stress, σy = 21100 psi
Stress Ratio, σ/σy = 0.142

At center of long side,

Maximum reaction force per unit length normal to the plate surface,

R = γ qb
= 8.81 lb/in
STIFFENER CALCULATION(at Roof Plate)

Short Beam

Maximum bending moment occurs at the point where dM/dx = 0 and shear force is zero,
that is, at the middle of the beam.

L= 1750 mm = 68.90 in
20.97 lb/in ґ= 1250 mm = 49.2 in
Load q = 0.426 psi
unit load W = qxґ psi
= 20.97 lb/in

FB 50 x 6
X
4
I = 0.5913 in
68.90 in
Wa Wb

Maximum moment,
At x = L/2 = 34.45 in
Mmax = WL 2/8
= 0 lb-in

M/I = σ/y

(I/y)required = M/σ
3
= 9.033E-06 in
Use FB 50 x 6
I/y = 1.582 in3 > (I/y)required then O.K

Therefore, σ = 0.301 psi < σallowable 52668 psi. then O.K

Maximum deflection at center of beam

At x = L/2 = 34.45 in

δmax = (5WL4)
384EI

= 0.380 >L/360 = 0.1914 in. Not O.K!!!

The size used unadequate!!!

STIFFENER PROPERTIES

Size FB 50 x 6
Material, 25% CrSDSS
Yield Stress, σy 79800 psi
Allowable Stress, σallowable 52668 psi

Stiffener b2 Where :

h2 d1 = 6 mm
d2 = 50 mm
2 d2
b1 = 166 mm *
b2 = 6 mm
y2 h1
C C
1 d1
y1
b1

Plate

PART area (a) y axy h h2 a x h2 bd3/12

mm2 mm3
2 4
mm mm mm mm mm4
1 993.3137 3 2979.941 6.49 42.1843 41902.24 2979.941
2 300 31 9300 21.51 462.4674 138740.2 62500
TOTAL 1293.314 12279.94 180642.5 65479.94

Therefore,

C = 9.49 mm

4
I = 246122.4 mm = 0.5913 in4

3
Z (I/C) = 25921.42 mm = 1.5818 in3

"*"
b1 =

b1 = 166 mm take min. L = 3400 mm, so R:

R= 1700 mm
Opening Calculation Per API 650

Without Repad

P Design 0.07 Barg

R Tank volume 29750000000 mm3
t Vessel wall thickness 6 mm
Rn Nozzle inside radius 80 mm
tn Nozzle wall thickness 4.78 mm

Rm Mean radius of vessel 29750000003 mm

Rnm Mean radius of nozzle 82.39 mm
As Shaded(cross-hatched) area 2535079.16 mm2
S Maximum allowable stress 21100 psi 1455.172 bar

Sm= Px ((Rx (Rn+ tn+ (Rmx t)^0.5)+ (Rnx (t+ (Rnmx tn)^0.5)))/ As)

= 347136064 bar < 1455.172414 bar

Sm < S OK.

Therefore Reinforcement Pad not required

Opening Calculation Per API 650

Without Repad

P Design 0.07 Barg

R Tank volume 29750000000 mm3
t Vessel wall thickness 6 mm
Rn Nozzle inside radius 50 mm
tn Nozzle wall thickness 3.91 mm

Rm Mean radius of vessel 29750000003 mm

Rnm Mean radius of nozzle 51.955 mm
As Shaded(cross-hatched) area 2535034.81 mm2
S Maximum allowable stress 21100 psi 1455.172 bar

Sm= Px ((Rx (Rn+ tn+ (Rmx t)^0.5)+ (Rnx (t+ (Rnmx tn)^0.5)))/ As)

= 347116778 bar < 1455.172414 bar

Sm < S OK.

Therefore Reinforcement Pad not required

Opening Calculation Per API 650

Without Repad

P Design 0.07 Barg

R Tank volume 29750000000 mm3
t Vessel wall thickness 6 mm
Rn Nozzle inside radius 50 mm
tn Nozzle wall thickness 7.11 mm

Rm Mean radius of vessel 29750000003 mm

Rnm Mean radius of nozzle 53.555 mm
As Shaded(cross-hatched) area 2535137.022 mm2
S Maximum allowable stress 21100 psi 1455.172 bar

Sm= Px ((Rx (Rn+ tn+ (Rmx t)^0.5)+ (Rnx (t+ (Rnmx tn)^0.5)))/ As)

= 347105411 bar < 1455.172414 bar

Sm < S OK.

Therefore Reinforcement Pad not required

Opening Calculation Per API 650

Without Repad

P Design 0.07 Barg

R Tank volume 29750000000 mm3
t Vessel wall thickness 6 mm
Rn Nozzle inside radius 200 mm
tn Nozzle wall thickness 8.18 mm

Rm Mean radius of vessel 29750000003 mm

Rnm Mean radius of nozzle 204.09 mm
As Shaded(cross-hatched) area 2535338.927 mm2
S Maximum allowable stress 21100 psi 1455.172 bar

Sm= Px ((Rx (Rn+ tn+ (Rmx t)^0.5)+ (Rnx (t+ (Rnmx tn)^0.5)))/ As)

= 347201856 bar < 1455.172414 bar

Sm < S OK.

Therefore Reinforcement Pad not required

Opening Calculation Per API 650

Without Repad

P Design 0.07 Barg

R Tank volume 29750000000 mm3
t Vessel wall thickness 6 mm
Rn Nozzle inside radius 100 mm
tn Nozzle wall thickness 6.02 mm

Rm Mean radius of vessel 29750000003 mm

Rnm Mean radius of nozzle 103.01 mm
As Shaded(cross-hatched) area 2535141.652 mm2
S Maximum allowable stress 21100 psi 1455.172 bar

Sm= Px ((Rx (Rn+ tn+ (Rmx t)^0.5)+ (Rnx (t+ (Rnmx tn)^0.5)))/ As)

= 347144954 bar < 1455.172414 bar

Sm < S OK.

Therefore Reinforcement Pad not required

Opening Calculation Per API 650

Without Repad

P Design 0.07 Barg

R Tank volume 29750000000 mm3
t Vessel wall thickness 6 mm
Rn Nozzle inside radius 250 mm
tn Nozzle wall thickness 9.27 mm

Rm Mean radius of vessel 29750000003 mm

Rnm Mean radius of nozzle 254.635 mm
As Shaded(cross-hatched) area 2535461.621 mm2
S Maximum allowable stress 21100 psi 1455.172 bar

Sm= Px ((Rx (Rn+ tn+ (Rmx t)^0.5)+ (Rnx (t+ (Rnmx tn)^0.5)))/ As)

= 347227018 bar < 1455.172414 bar

Sm < S OK.

Therefore Reinforcement Pad not required

WIND LOADING - BS 6399 - PART 2 -1997

Terrain Category = 1

Region = D

Basic Wind Speed Vb = 53.80 m/s

Shielding Factor Ms = 1

Topographic Factor Sa = 1

Direction Factor Sd = 1

Probability Factor Sp = 1

Seasonal Factor Ss = 1

Terrain and Building Factor Sb = 1

Design Wind Speed Vz = 53.80 m/s ( Vb x Sa x Sd x Sp x Ss )

Effective (Design) Wind speed Ve = 53.80 m/s ( Vz x Sb )

Dynamic Pressure qz = 1.7743 kPa ( 0.613 x Ve 2 x 10-3 )

Drag Coefficient Cd = 1

H = 3400.000 mm

L = 2500.000 mm

2
Az = 8500000.000 mm
3400

H /L = 1.36

2500.000 Kar = 1

Cd' = 1 ( Cd x Kar )

Wind Force Fw = 15081.5 N ( Cd' x qz x Az ) / 103

Height to COA h = 1700.000 mm (H/2)

Overturning Moment Mw = 25638515 Nmm ( Fw x h )

Moment at the joint of the leg to the tank

hT = 550 mm Mw1 = 26309411 Nmm Mw - hT ( Fw - 0.5*qz*D*hT )
Sesmic Load
L: lenth of the tank 3500 mm
H: Height of the tank 3400 mm
V: Wind speed 53.8 m/s
a1: Horizontal acceleration 0.8 m/s2
2
a2: Vertical acceleration 2 m/s
M: Empty Weight 4167 kg
2
S1y: Yield Stress of bottom plate 262 N/mm
2
Sa: Allowable Stress of the plate 137 N/mm
S2y: Yield Stress of beam 355 N/mm2
f: Fillet weld size between bottom plate and skid 6 mm
Lf: Weld leg between the beam and bottom plate 300 mm

Wind Force Calculation

2
A=LxH= 11.9 m
Fw=0.5 x A x V2= 17221.92 N
2
P=F/A= 1447.22 N/m

Force Calculation
Fh=(a1+1) x M x 10= 75006 N
Fv=(a2+1) x M x 10= 125010 N

Horizontal Shear Stress Check

Fhc=Fw+Fh= 92227.92 N
Maximum Shear Stress
2
Ss=0.4 x S2y= 142 N/mm
Fhc=Ss x (Lf x f)
so Lf=Fc / (Ss x f)= 108.2487 mm
As the welding seam length along the skid to bottom is more than required, so it's OK!

Vertical Shear Stress Check

Fv= 125010 N
Fv=Ss x (Lf x f)
so Lf=Fv / (Ss x f)= 146.7254 mm
As the welding seam length along the skit to bottom is more than required, so it's OK!

Over Turning Force Check

Fv x L/2 + Fhc x H/2 = M x L/2 + Ss x (Lf x f) x L/2
so Lf=2(Fv x L/2 + Fhc x H/2 - M x L/2) / (Ss x f x L) = 246.9904 mm
As the welding seam length along the skid to bottom is more than required, so it's OK!
Blast Load
L: Length of the tank 3500 mm
H: Height of the tank 3400 mm
P: Blast load 20000 N/m2
2
a1: Horizontal acceleration 0.3 m/s
a2: Vertical acceleration 1.4 m/s2
M: Empty Weight 4167 kg
2
S1y: Yield Stress of bottom plate 262 N/mm
S2y: Yield Stress of beam 355 N/mm2
f: Fillet weld size between bottom plate and skid 6 mm
Lf: Weld leg between the beam and bottom plate 300 mm

Blast Force Calculation

2
A=LxH= 11.9 mm
Fw=P x A = 238000 N

Transportation Force Calculation

Fh=(a1+1) x M x 10 = 54171 N
Fv=(a2+1) x M x 10 = 100008 N

Horizontal Shear Stress Check

Ss=0.4 x S2y= 142 N/mm2
Fhc=S2y x (Lf x f)
so Lf=Fc / (S2y x f)= 137.1695 mm
As the welding seam length along the skid to bottom is more than required, so it's OK!
As the welding seam length along the skid to bottom is more than required, so it's OK!
Vertical Shear Stress Check
Fv= 100008 N
Fv=S2y x (Lf x f)
so Lf=Fv / (S2y x f)= 46.95211 mm
As the welding seam length along the skid to bottom is more than required, so it's OK!

Over Turning Force Check

Fv xL/2 + Fhc x H/2 = M x L/2 + S2y x (Lf x f) x L/2
so Lf=2(Fv x L/2 + Fhc x H/2 - M x L/2) / (S2y x f x L) = 178.2461 mm
As the welding seam length along the skit to bottom is more than required, so it's OK!
As the welding seam length along the skid to bottom is more than required, so it's OK!
WEIGHT SUMMARY

ITEM : 53TB001A/B/C
JOB NO. JN05-320
QTY or
ITEM DESCRIPTION UNIT WT. WEIGHT

SIDE PLATE 3.500 m x 3.400 m x 6 thk 2 1116.7 kg

SIDE PLATE 2.500 m x 3.400 m x 6 thk 2 797.6 kg
BASE PLATE 3.500 m x 2.500 m x 6 thk 1 410.6 kg
ROOF PLATE 3.500 m x 2.500 m x 6 thk 1 420.0 kg

STIFFENER
SIDE WALL FB 50 x 6 x 28 m 1 65.7 kg

ROOF PLATE FB 50 x 6 x 8 m 1 19.2 kg

BOTTOM PLATE FB 50 x 6 x 8 m 4 307.2 kg

CHANNEL 150 x 75 x 6.5t x 0.6 m 1 29.9 kg

NOZZLE / OPENINGS 1000.0 kg

AND OTHERS

TOTAL WEIGHT 4167 kg

Liquid Weight 38675 kg

Water Weight 29750 kg

EMPTY WEIGHT 4167 kg

OPERATING WEIGHT 42842 kg
FULL WATER WEIGHT 33917 kg
TRANSPORTATION LOADS

TRANSPORTATION ACCELERATIONS

WEIGHTS

ERECTED 22222..22. We = 4167 kg -> 40877 N

OPERATING 22222.. Wo = 42842 kg -> 420279 N

FLOODED 2222.22 Wf = 33917 kg -> 332724 N

VERTICAL AtV = 3.92 m/s ( 1.4 x g )

LONGITUDINAL AtH = 3.92 m/s ( 0.5 x g )

TRANSVERSE AtT = 7.85 m/s ( 0.5 x g )

TRANSPORTATION FORCES

VERTICAL FtV = 16350.7 N ( We x AtV )

HORIZONTAL FtH = 16350.7 N ( We x AtH )

TRANSVERSE FtT = 32701.5 N ( We x AtT )

LOADS AT BASE

WEIGHTS

Erected We = 4167 kg ------> 40877 N

Operating Wo = 42842 kg ------> 420279 N
Flooded Wf = 33917 kg ------> 332724 N

EXTERNAL LOADS

Wind Force Fw = 15081 N

Earthquake Force Feq = 31860 N
Blasting Force Fb = 23080 N
FD 2 2 0.5
Client Specified Dynamic Force = 26642 N [( 0.5 x We ) + ( 1.4 x We ) ]
( during tow-out and installation )

Wind Moment Mw = 25638515 Nmm

Earthquake Moment Meq = 142 Nmm
Blasting Moment Mb = 142 Nmm
Client Specified Moment Mc = 0 Nmm ( FD x COGerected ) COGerected = 1325 mm
( during tow-out and installation ) (from base)

Maximun Shear Force F = 31860 N >>> P = F/n = 7965.0 N

Maximun O/T Moment M = 25638515 Nmm n= 4
where, n = no of leg.

HOLD DOWN BOLTS

Bolt Material22222.222222.2222.
= SA 193M GR B7

Bolt Yield Stress2222222.22222

Sy = 207 MPa

Bolt UTS22.2..222222.22222
Su = 507 MPa

Allowable Tensile222222.2..2...22
Ft = 124.2 MPa

Allowable Shear22222222...22
Fs = 69 MPa

Bolt Size22222222222222...22222
= M16

Bolt Number2222222222..2...2222
N = 4

AT =
Tensile Area2222.22222..2.22 245 mm2

AS
Shear Area22222222222..2 = 400 mm2

Bolt PCD2222222222222..
PCD = 141 mm

AXIAL STRESS IN BOLT SHEAR STRESS IN BOLT

Load / Bolt, P= 4Mw - We Shear / Bolt, S = F

PCD.N N N x As

Load / Bolt = 171614 N fs = 19.91 MPa OK

** Since the value is -ve, therefore no axial stress Fs = 69 MPa

since fs < Fs the shear stress is OK

LEG DESIGN

LEG DATA

Material.....= SA 36M
2
Yield Stress, Sy...= 248.2 N/mm
2
Allowable Axial Stress, fall....= 148.9 N/mm ( 0.6 x Sy )
2
Allowable Bending Stress, fball.......= 165.5 N/mm ( 2/3 x Sy )

LEG GEOMETRY :- CHANNEL150 x 75 x6.5t

A= 2370 mm2
4
Ixx = 8640000 mm
d d= 51.9 mm
e= 23.1 mm
L= 450 mm
X X r= 10 mm

AXIAL STRESS

Axial Stress, fa = F/A = 35.10 N/mm2

BENDING STRESS

Bending Stress, fb = PxLxe= 18.14 N/mm2

Ixx

COMBINED STRESS

Combined Stress, f = (fa/fall + fb/fball) = 0.35

Since Combined Stress is < 1.00 The Leg Design is OK!

LEG BASE PLATE DESIGN

Refer Dennis R Moss Procedure 3-10

tb = 3xQxF
4 x A x Fb

Q = Maximum Load / Support = 42842 N

F = Baseplate Width = 200 mm
A = Baseplate Length = 200 mm
Fb = Allowable Bending Stress = 163.68 MPa ( 0.66 Fy )

tb = 14.0 mm

Use Tb = 15 mm OK

BASE PLATE WELD CHECKING

Maximum stress due to Q & F = max(Q, F)/Aw = 6.69 N/mm2
< 86.9 N/mm2 OK

Weld leg size, g = 8.0 mm

Length of weld, l = 2*( 2*F + 2*A ) = 1600 mm
Area of weld, Aw = 0.5*g*l = 6400 mm2
Joint efficiency for fillet weld, E = 0.6 -
Welding stress for steel, fw = 144.8 N/mm2
Allowable stress for weld, fw = E*fw = 86.9 N/mm2
Maximum vertical force, Q = 42841.9 N
Maximum horizontal force, F = 31860.0 N
LIFTING LUG DESIGN CALCULATION
Fy

U
tL
rL d
5
A A
J
5 k
tM
M

b hc
Wp

a tp
Lp 10
5
Pa
Weight of tank, We = 4,167 kg
= 40,877 N
Number of lifting lug, N = 4

1.1 LIFTING LUG

Distance, hc = 85 mm
Distance k = 106 mm
Distance J = 48 mm
Distance M = 50 mm
Lug radius, rL = 50 mm
Diameter of hole, d = 40 mm
Lug thickness, tL = 15 mm
Plate thickness, tM = 9 mm
Length a = 100 mm
Length b = 60 mm
Pad length, Lp = 150 mm
Pad width, Wp = 100 mm
Pad thickness, tp = 6 mm
Angle, U (max) = 15 °

Shackle S.W.L : 4.75 tons

Type of shackle : Chain Shackles
Pin size, Dp = 22.225 mm

2.0 LIFTING LUG MATERIAL & MECHANICAL PROPERTIES

Material used = SA 240M GR 316 L
Specified yield stress, Sy = 248.22 N/mm²
Impact load factor, p = 3.00

3.0 ALLOWABLE STRESSES

Allowable tensile stress, St.all ( = 0.6 Sy ) = 148.93 N/mm²
Allowable bearing stress, Sbr.all ( = 0.9 Sy ) = 223.40 N/mm²
Allowable bending stress, Sbn.all ( = 0.66 Sy ) = 163.83 N/mm²
Allowable shear stress,(Ss.all
Cd' x (qz
= x0.4 ) x)103
AzSy = 99.29 N/mm²
4.0 LIFTING LUG DESIGN - VERTICAL LIFTING
4.1 DESIGN LOAD
Design load , Wt ( = p.We ) = 122631 N
Design load per lug, W ( = Wt / N ) = 30658 N
Vertical component force, Fy = 30658 N

4.2 STRESS CHECK AT PIN HOLE

(a) Tensile Stress
Vertical component force, Fy = 30658 N
Cross sectional area of lug eye, Ae ( = 2*[ rL - d/2 ] x tL ) = 900 mm²
Tensile stress, St ( = Fy / Ae ) = 34.06 N/mm²
Since St < St.all, therefore the lifting lug size is satisfactory.

(b) Bearing Stress

Vertical component force, Fy = 30658 N
Cross sectional area of lug eye, Ae ( = Dp x tL ) = 333 mm²
Bearing stress, Sbr ( = Fy / Ae ) = 91.96 N/mm²
Since Sbr < Sbr.all,therefore the lifting lug size is satisfactory.

(c) Shear Stress

Vertical component force, Fy = 30658 N
Cross sectional area of lug eye, Ae ( = 2.(rL-d/2).tL ) = 900 mm²
Shear stress, Ss ( = Fy / Ae ) = 34.06 N/mm²
Since Ss < Ss.all,therefore the lifting lug size is satisfactory.

5.0 STRESS CHECK AT SECTION A-A

(a) Bending Stress
Bending stress due to Pa ( = Fy x tan U ) = 8215 N
Bending moment, Mb ( = Pa x J ) = 394305 Nmm
Section modulus, Z ( = 2rL*tL 2/6 = 3750 mm3
Bending stress, Sb ( = Mb/Z ) = 105.15 N/mm²
Since Sb < Sb.all, therefore the lifting lug size is satisfactory.

(b) Tensile Stress due to Fy

Cross section area, Ae (=2rL x tL) = 1500 mm²
Tensile Stress, St (=Fy/Ae) = 20.44 N/mm²
Since St < St.all, therefore the lifting lug size is satisfactory.

Combine Stress Ratio, CS (= St/St.all + Sb/Sbn.all) = 0.78

Since CS <= 1.0, therefore lifting lug size is satisfactory.

6.0 DESIGN OF WELD SIZE AT LUG TO PAD JOINT

6.1 GENERAL
Weld leg , w1 = 10 mm
Weld throat thickness, tr1 = 7.1 mm
Weld leg , w1 = 10 mm
Weld throat thickness, tr2 = 7.1 mm
Fillet weld joint efficiency, E = 0.6
Allowable welding stress for steel grade 43 ( E-43 ) = 125 N/mm²

6.2 CRITICAL WELD CROSS-SECTIONAL PROPERTIES

Area of weld, Aw1 ( = tr1 ( a + 2b ) = 1555 mm²
Area of weld, Aw2 ( = tr2 ( (2a-tM) + (2M+tM ))) = 2121 mm²
Total area of weld, Aw ( = Aw1 + Aw2 ) = 3676 mm²

6.3 STRESS DUE TO FORCE Fy

Component force, Fy = 30658 N
Shear stress, Ssx ( = Fy / Aw ) = 8.34 N/mm²
Allowable welding stress, Sa ( = E.Sa ) = 75.00 N/mm²
Since Ssx < Sa, therefore the selected weld size is satisfactory .
7.0 DESIGN OF WELD SIZE AT PAD TO TANK JOINT
7.1 GENERAL
Weld leg , w = 6 mm
Weld throat thickness, tr = 4.2 mm
Fillet weld joint efficiency, E = 0.6
Allowable welding stress for steel grade 43 ( E-43 ) = 125 N/mm²

7.2 CRITICAL WELD CROSS-SECTIONAL PROPERTIES

Area of weld, Aw ( = 2 tr ( Wp + Lp ) ) = 2121 mm²

7.3 STRESS DUE TO FORCE Fy

Component force, Fy = 30658 N
Shear stress, Ssx ( = Fy / Aw ) = 14.45 N/mm²
Allowable welding stress, Sa ( = E.Sa ) = 75.00 N/mm²
Since Ssx < Sa, therefore the selected weld size is satisfactory .
 Job No Sheet No Rev
1
Part

Job Title Ref

By Date22-May-14 Chd

Client File Date/Time 22-May-2014

Porable Water Tank Skid Transport Condition.std 04:13

Job Information
Engineer Checked Approved

Name:
Date: 22-May-14

Structure Type SPACE FRAME

Number of Nodes 25 Highest Node 25

Number of Elements 36 Highest Beam 36

Number of Basic Load Cases 2

Number of Combination Load Cases 1

Included in this printout are data for:

All The Whole Structure

Included in this printout are results for load cases:

Type L/C Name

Primary 1 SELF WEIGHT

Primary 2 LIVE LOADS
Combination 3 COMBINATION LOAD CASE 3

Nodes
Node X Y Z
(mm) (mm) (mm)
1 0.000 0.000 0.000
2 3.5E+3 0.000 0.000
3 7E+3 0.000 0.000
4 10.5E+3 0.000 0.000
5 0.000 0.000 -2.6E+3
6 3.5E+3 0.000 -2.6E+3
7 7E+3 0.000 -2.6E+3
8 10.5E+3 0.000 -2.6E+3
9 5.25E+3 0.000 0.000
10 5.25E+3 0.000 -2.6E+3
11 8.75E+3 0.000 0.000
12 8.75E+3 0.000 -2.6E+3
13 1.75E+3 0.000 0.000
14 1.75E+3 0.000 -2.6E+3
15 0.000 0.000 -1.3E+3
16 1.75E+3 0.000 -1.3E+3
17 3.5E+3 0.000 -1.3E+3
18 5.25E+3 0.000 -1.3E+3
19 7E+3 0.000 -1.3E+3
20 8.75E+3 0.000 -1.3E+3
21 10.5E+3 0.000 -1.3E+3
22 875.000 0.000 0.000
23 875.000 0.000 -2.6E+3
24 9.63E+3 0.000 0.000

Print Time/Date: 22/05/2014 04:15 STAAD.Pro V8i (SELECTseries 2) 20.07.07.19 Print Run 1 of 6
 Job No Sheet No Rev
2
Part

Job Title Ref

By Date22-May-14 Chd

Client File Date/Time 22-May-2014

Porable Water Tank Skid Transport Condition.std 04:13

Nodes Cont...
Node X Y Z
(mm) (mm) (mm)
25 9.63E+3 0.000 -2.6E+3

Beams
Beam Node A Node B Length Property β
(mm) (degrees)
1 1 22 875.000 2 0
2 2 9 1.75E+3 2 0
3 3 11 1.75E+3 2 0
4 5 23 875.000 2 0
5 6 10 1.75E+3 2 0
6 7 12 1.75E+3 2 0
7 5 15 1.3E+3 2 0
8 6 17 1.3E+3 2 0
9 7 19 1.3E+3 2 0
10 8 21 1.3E+3 2 0
11 9 3 1.75E+3 2 0
12 10 7 1.75E+3 2 0
13 11 24 875.000 2 0
14 12 25 875.000 2 0
15 11 20 1.3E+3 2 0
16 9 18 1.3E+3 2 0
17 13 2 1.75E+3 2 0
18 14 6 1.75E+3 2 0
19 13 16 1.3E+3 2 0
20 15 1 1.3E+3 2 0
21 16 14 1.3E+3 2 0
22 17 2 1.3E+3 2 0
23 18 10 1.3E+3 2 0
24 19 3 1.3E+3 2 0
25 20 12 1.3E+3 2 0
26 21 4 1.3E+3 2 0
27 15 16 1.75E+3 2 0
28 16 17 1.75E+3 2 0
29 17 18 1.75E+3 2 0
30 18 19 1.75E+3 2 0
31 19 20 1.75E+3 2 0
32 20 21 1.75E+3 2 0
33 22 13 875.000 2 0
34 23 14 875.000 2 0
35 24 4 875.000 2 0
36 25 8 875.000 2 0

Section Properties
Prop Section Area Iyy Izz J Material
(cm2) (cm4) (cm4) (cm4)
2 UB200X18.2 23.200 114.000 1.58E+3 2.823 STEEL

Print Time/Date: 22/05/2014 04:15 STAAD.Pro V8i (SELECTseries 2) 20.07.07.19 Print Run 2 of 6
 Job No Sheet No Rev
3
Part

Job Title Ref

By Date22-May-14 Chd

Client File Date/Time 22-May-2014

Porable Water Tank Skid Transport Condition.std 04:13

Materials
Mat Name E ν Density α
(kN/mm 2) (kg/m3) (/°C)
1 STEEL 205.000 0.300 7.83E+3 12E -6
2 STAINLESSSTEEL 197.930 0.300 7.83E+3 18E -6
3 ALUMINUM 68.948 0.330 2.71E+3 23E -6
4 CONCRETE 21.718 0.170 2.4E+3 10E -6

Supports
Node X Y Z rX rY rZ
(kN/mm) (kN/mm) (kN/mm) (kN-m/deg) (kN-m/deg) (kN-m/deg)
1 Fixed Fixed Fixed Fixed Fixed Fixed
2 Fixed Fixed Fixed Fixed Fixed Fixed
3 Fixed Fixed Fixed Fixed Fixed Fixed
4 Fixed Fixed Fixed Fixed Fixed Fixed
5 Fixed Fixed Fixed Fixed Fixed Fixed
6 Fixed Fixed Fixed Fixed Fixed Fixed
7 Fixed Fixed Fixed Fixed Fixed Fixed
8 Fixed Fixed Fixed Fixed Fixed Fixed

Basic Load Cases

Number Name

1 SELF WEIGHT
2 LIVE LOADS

Combination Load Cases

Comb. Combination L/C Name Primary Primary L/C Name Factor

3 COMBINATION LOAD CASE 3 1 SELF WEIGHT 1.00

2 LIVE LOADS 1.00

Print Time/Date: 22/05/2014 04:15 STAAD.Pro V8i (SELECTseries 2) 20.07.07.19 Print Run 3 of 6
 Job No Sheet No Rev
4
Part

Job Title Ref

By Date22-May-14 Chd

Client File Date/Time 22-May-2014

Porable Water Tank Skid Transport Condition.std 04:13

Utilization Ratio
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
1 UB200X18.2 UB200X18.2 0.293 1.000 0.293 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
2 UB200X18.2 UB200X18.2 0.290 1.000 0.290 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
3 UB200X18.2 UB200X18.2 0.322 1.000 0.322 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
4 UB200X18.2 UB200X18.2 0.293 1.000 0.293 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
5 UB200X18.2 UB200X18.2 0.290 1.000 0.290 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
6 UB200X18.2 UB200X18.2 0.322 1.000 0.322 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
7 UB200X18.2 UB200X18.2 0.190 1.000 0.190 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
8 UB200X18.2 UB200X18.2 0.497 1.000 0.497 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
9 UB200X18.2 UB200X18.2 0.497 1.000 0.497 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
10 UB200X18.2 UB200X18.2 0.190 1.000 0.190 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
11 UB200X18.2 UB200X18.2 0.290 1.000 0.290 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
12 UB200X18.2 UB200X18.2 0.290 1.000 0.290 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
13 UB200X18.2 UB200X18.2 0.207 1.000 0.207 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
14 UB200X18.2 UB200X18.2 0.207 1.000 0.207 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
15 UB200X18.2 UB200X18.2 0.274 1.000 0.274 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
16 UB200X18.2 UB200X18.2 0.181 1.000 0.181 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
17 UB200X18.2 UB200X18.2 0.322 1.000 0.322 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
18 UB200X18.2 UB200X18.2 0.322 1.000 0.322 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
19 UB200X18.2 UB200X18.2 0.274 1.000 0.274 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
20 UB200X18.2 UB200X18.2 0.190 1.000 0.190 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
21 UB200X18.2 UB200X18.2 0.274 1.000 0.274 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
22 UB200X18.2 UB200X18.2 0.497 1.000 0.497 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
23 UB200X18.2 UB200X18.2 0.181 1.000 0.181 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
24 UB200X18.2 UB200X18.2 0.497 1.000 0.497 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
25 UB200X18.2 UB200X18.2 0.274 1.000 0.274 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
26 UB200X18.2 UB200X18.2 0.190 1.000 0.190 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
27 UB200X18.2 UB200X18.2 0.245 1.000 0.245 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
28 UB200X18.2 UB200X18.2 0.349 1.000 0.349 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
29 UB200X18.2 UB200X18.2 0.349 1.000 0.349 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
30 UB200X18.2 UB200X18.2 0.349 1.000 0.349 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
31 UB200X18.2 UB200X18.2 0.349 1.000 0.349 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
32 UB200X18.2 UB200X18.2 0.245 1.000 0.245 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
33 UB200X18.2 UB200X18.2 0.207 1.000 0.207 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
34 UB200X18.2 UB200X18.2 0.207 1.000 0.207 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
35 UB200X18.2 UB200X18.2 0.293 1.000 0.293 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860
36 UB200X18.2 UB200X18.2 0.293 1.000 0.293 AISC- H1-3 3 23.200 1.58E+3 114.000 3.860

Print Time/Date: 22/05/2014 04:15 STAAD.Pro V8i (SELECTseries 2) 20.07.07.19 Print Run 4 of 6
 Job No Sheet No Rev
5
Part
Software licensed to Emerson Process Management Asia Pacific Pte Ltd
Job Title Ref

By Date22-May-14 Chd

Client File Date/Time 22-May-2014

Porable Water Tank Skid Transport Condition.std 04:13

Reaction Summary
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(N) (N) (N) (kNm) (kNm) (kNm)
Max FX 1 1:SELF WEIGHT 0.000 1.41E+3 0.000 0.331 0.000 0.545
Min FX 1 1:SELF WEIGHT 0.000 1.41E+3 0.000 0.331 0.000 0.545
Max FY 2 0.000
3:COMBINATION LOAD CASE 45.1
3 E+3 0.000 13.096 0.000 -0.842
Min FY 1 1:SELF WEIGHT 0.000 1.41E+3 0.000 0.331 0.000 0.545
Max FZ 1 1:SELF WEIGHT 0.000 1.41E+3 0.000 0.331 0.000 0.545
Min FZ 1 1:SELF WEIGHT 0.000 1.41E+3 0.000 0.331 0.000 0.545
Max MX 2 0.000
3:COMBINATION LOAD CASE 45.1
3 E+3 0.000 13.096 0.000 -0.842
Min MX 6 0.000
3:COMBINATION LOAD CASE 45.1
3 E+3 0.000 -13.096 0.000 -0.842
Max MY 1 1:SELF WEIGHT 0.000 1.41E+3 0.000 0.331 0.000 0.545
Min MY 1 1:SELF WEIGHT 0.000 1.41E+3 0.000 0.331 0.000 0.545
Max MZ 1 0.000
3:COMBINATION LOAD CASE 20.7
3 E+3 0.000 5.005 0.000 8.500
Min MZ 4 0.000
3:COMBINATION LOAD CASE 20.7
3 E+3 0.000 5.005 0.000 -8.500

3D Rendered View

Print Time/Date: 22/05/2014 04:15 STAAD.Pro V8i (SELECTseries 2) 20.07.07.19 Print Run 5 of 6
 Job No Sheet No Rev
6
Part
Software licensed to Emerson Process Management Asia Pacific Pte Ltd
Job Title Ref

By Date22-May-14 Chd

Client File Date/Time 22-May-2014

Porable Water Tank Skid Transport Condition.std 04:13

X = 0.000 N
Y = 1410.513 N
Z = 0.000 N
MX = -0.331 kNm
MY = 0.000 kNm
X = 0.000 N
MZ = -0.545 kNm
Y = 2810.436 N
Z = 0.000 N 8
MX = -0.741 kNm
X = 0.000 N 25
MY = 0.000 kNm
Y = 2810.436 N MZ = 0.048 kNm 12
Z = 0.000 N 21
MX = -0.741 kNm
MY = 0.000 kNm 7
MZ = -0.048 kNm 20
4
10 24
X = 0.000 N 19 X = 0.000 N
Y = 1410.513 N 11 Y = 1410.513 N
Z = 0.000 N 6 Z = 0.000 N
MX = -0.331 kNm 18 MX = 0.331 kNm
MY = 0.000 kNm 3 MY = 0.000 kNm
MZ = 0.545 kNm 14 MZ = -0.545 kNm
17 X = 0.000 N
23 9 Y = 2810.436 N
5 Z = 0.000 N
16 MX = 0.741 kNm
2 MY = 0.000 kNm
MZ = 0.048 kNm
15 X = 0.000 N
13 Y = 2810.436 N
Z = 0.000 N
22
Y MX = 0.741 kNm
X X = 0.000 N 1 MY = 0.000 kNm
Z Y = 1410.513 N MZ = -0.048 kNm
Load 1
Z = 0.000 N
MX = 0.331 kNm
MY = 0.000 kNm
MZ = 0.545 kNm

Whole Structure

Print Time/Date: 22/05/2014 04:15 STAAD.Pro V8i (SELECTseries 2) 20.07.07.19 Print Run 6 of 6