The Origins of CAD/CAM
The Origins of CAD/CAM
From this inception, it has been human nature to innovate, discover, invent new things
and so has been his creation. Design may be pronounced as the synonym for creation. So there is
no end to man’s creation, design and hence CAD. By passage of time it’ll be even smarter,
quicker and sophisticated. COMPUTER-AIDED DESIGN (CAD) AND COMPUTER-AIDED
MANUFACTURING (CAM).
The Origins of CAD/CAM:
CAD had its origins in three separate sources, which also serve to highlight the basic
operations that CAD systems provide.
The first source of CAD resulted from attempts to automate the drafting process. These
developments were pioneered by the General Motors Research Laboratories in the early 1960s.
One of the important time-saving advantages of computer modeling over traditional drafting
methods is that the former can be quickly corrected or manipulated by changing a
model's parameters.
The second source of CAD was in the testing of designs by simulation. The use of
computer modeling to test products was pioneered by high-tech industries like aerospace and
semiconductors.
The third source of CAD development resulted from efforts to facilitate the flow from the
design process to the manufacturing process using numerical control (NC) technologies, which
enjoyed widespread use in many applications by the mid-1960s. It was this source that resulted
in the linkage between CAD and CAM. One of the most important trends in CAD/CAM
technologies is the ever-tighter integration between the design and manufacturing stages of
CAD/CAM-based production processes.
The development of CAD and CAM and particularly the linkage between the two,
overcame traditional NC shortcomings, in expense, ease of use, and speed by enabling the design
and manufacture of a part to be undertaken using the same system of encoding geometrical data.
This innovation greatly shortened the period between design and manufacture and greatly
expanded the scope of production processes for which automated machinery could be
economically used. Just as important, CAD/CAM gave the designer much more direct control
over the production process, creating the possibility of completely integrated design and
1
manufacturing processes.
The rapid growth in the use of CAD/CAM technologies after the early 1970s was made
possible by the development of mass-produced silicon chips and the microprocessor, resulting in
more readily affordable computers. As the price of computers continued to decline and their
processing power improved, the use of CAD/CAM broadened from large firms using large-scale
mass production techniques to firms of all sizes. The scope of operations to which CAD/CAM
was applied broadened as well. In addition to parts-shaping by traditional machine tool processes
such as stamping, drilling, milling, and grinding, CAD/CAM has come to be used by firms
involved in producing consumer electronics, electronic components, molded plastics, and a host
of other products. Computers are also used to control a number of manufacturing processes (such
as chemical processing) that are not strictly defined as CAM because the control data are not
based on geometrical parameters.
2
While mechanical applications of CAD account for nearly one-half of the systems sold
today, other industries recognize the benefits it affords. For the electronics industry, CAD offers
considerable advantages, particularly in the design on printed circuit boards and integrated
circuits. The design of these components can be tedious and time consuming. And so many lines
and cross lines must be drawn that errors are not easily detected. CAD not only speeds up the
drawing but detects errors as well.
Architecture, engineering, and construction applications offer the greatest potential for
growth in sales, according to a recent industry survey. Although the construction and electronics
industries each represent about 16 percent of the CAD market now, the penetration is far less
extensive. However, both simple drafting applications and more complex design and analysis are
evident within the industry. Architectural drafters will be able to complete drawings of a higher
quality in much less time. Architects and engineers will be able to submit their designs to more
exhaustive structural and stress analyses. Piping and electrical layouts will be made easier and
the design and allocation of interior space will be facilitated as well. As a management tool, the
data base created during the project will provide an effective means of inventory control enabling
contractors not only to speed construction but to reduce costs.
CAD is also having an impact upon cartography. Geographers use CAD systems to help
them draft maps used for environmental impact analysis and land use planning and for charting
landfill contours for strip mining. Some software packages are available that aid in
extraterrestrial mapping.
Process industries, such as oil and gas refineries and chemical manufacturers, as well as
power and utility companies, must plan, construct, operate, and maintain electrical grid and
pipeline networks. CAD makes these complex tasks easier. CAD even has applications in
landscape design, interior design, and fashion design. Some high fashion couturiers use CAD
systems to lay out patterns on expensive fabrics as a way to minimize waste.
Using CAD, it is possible to simulate in three dimensions the movement of a part through
a production process. This process can simulate feed rates, angles and speeds of machine tools,
the position of part-holding clamps, as well as range and other constraints limiting the operations
of a machine. The continuing development of the simulation of various manufacturing processes
is one of the key means by which CAD and CAM systems are becoming increasingly integrated.
CAD/CAM systems also facilitate communication among those involved in design,
3
manufacturing, and other processes. This is of particular importance when one firm contracts
another to either design or produce a component.
CAD/ CAM (Definition): The process of creating, optimizing, analyzing and manufacturing a
product completely by the aid of computer is called CAD/CAM.
But decisions about technology are not like dropping an anchor. They are like spreading a sail.
Leaders of a manufacturing enterprise must set a course toward a destination, then be ready to
shift with the winds.
4
The following pages are meant to be a breezy review of the major currents blowing us toward the
future. They represent the forces that will both guide and propel the decision-making process.
Simultaneous Engineering:
Sharing information is another urgent issue where new techniques and methodologies
will have an impact. One of the most important of these is simultaneous engineering.
Simultaneous engineering (or concurrent engineering) can be defined as a methodology in which
the design of the product is accomplished simultaneously with the design of the process to
produce the product. In this methodology, design engineering works together with manufacturing
engineering and other related functions during the design phase to incorporate downstream
manufacturing considerations into the product design.
Companies that have implemented simultaneous engineering have typically experienced
fewer design changes, shorter lead times, lower manufacturing costs and improved quality. This
concept not only applies within a company, but can be extended to the supplier network. As a
5
company better understands the issues being faced by the supplier, and the supplier offers design
suggestions based upon manufacturing knowledge, a more effective process results. The
inclusion of suppliers and customers into the manufacturing process creates a "virtual factory."
Different companies will work so closely together as a team that it will be as if they were
actually a dedicated organization under one roof.
Maturity:
The CAD/CAM industry has become a multibillion dollar industry. In the 1990s, it will
become relatively mature. Industry growth rates, although substantial by most standards, will
ease. Acquisitions, mergers, and alliances will accelerate. The trends noted, for the most part, are
evolutionary and not revolutionary. Yet CAD/CAM in general, and automated manufacturing in
particular, will remain an exciting field.
6
New technologies will continue to emerge, and for the most part, will be introduced by
niche companies. User organizations will become more sophisticated and hence, more inclined to
implement the best product for the task at hand. World class manufacturing demands the
appropriate utilization of advanced technology. It is essential for those firms striving to remain
competitive in a worldwide marketplace.
7
COMPUTER AIDED DESIGN (CAD):
Computer-aided design (CAD) involves creating computer models defined by
geometrical parameters. These models typically appear on a computer monitor as a three-
dimensional representation of a part or a system of parts, which can be readily altered by
changing relevant parameters. CAD systems enable designers to view objects under a wide
variety of representations and to test these objects by simulating real-world conditions.
Features:
Enhanced Geometry Creation:
The 1990s will see substantial enhancements in geometry creation, including solid
modeling, feature-based geometry, associativity, inference systems, parametric design, and
variational geometry functionality. Moreover, system architectures of the 1990s are likely to
have a separate geometry subsystem that will serve all applications.
Geometry subsystems are now being independently developed and marketed in the same
manner as database management, graphics, and data communication systems. They will provide
a geometry toolkit to be utilized by all applications.
Advanced geometry software systems will provide an architecture in which wireframe,
surface, and solid representations can be intermixed within the same model. Such a system will
support applications that involve time, the fourth dimension. For example, this capability will
8
permit direct computation of potential collisions between two solid objects moving through
space, as in robotic or machining applications. Solid models provide a complete and
unambiguous representation of a real object. They permit a more direct and accurate computation
of mass properties. Internal characteristics of the object can also be included in the model.
Solid product models will form the core for a single product definition in a CAD
environment. All functions will reference this model. NC machining systems, now under
development in some firms, will be introduced to machine directly off a solid model.
Feature-based or form-feature-based modeling is a higher level of design. It recognizes
that designers and engineers generally think in terms of blind holes, through-holes, slots, shafts,
chamfers, ribs, rounds, fillets, and so on, rather than lines, circles, arcs, or Boolean manipulation
of solid objects such as boxes, cylinders, or cones. Furthermore, the direct creation of a feature,
as opposed to a buildup of the feature, improves the productivity of designers.
A related capability is Associativity. In associative systems, relationships are established
between models and dimensions in such a way that changes in the model or its dimensions result
in an automatic update of other related models or dimensions. Further, a change to a part within
an assembly can trigger a corresponding change to that part in other assemblies.
In an inference system, the CAD system infers the next step by the operator. It
automatically generates the next line, arc, circle, and so on. This is usually done by placement of
the mouse pointer or other input device. By so doing, design productivity is increased. If the
system inference is incorrect, it can be undone and re-entered.
Parametric design systems were introduced in the 1980s. In these systems, parameters are
established as opposed to actual dimensions. Relationships can also be established among the
parameters. For example, one side of an object is always twice that of another side of an object.
When combined with an associativity capability, a powerful system results. A change in one
dimension can also change other dimensions and update the geometric model.
A similar but somewhat more powerful capability is that of variational geometry. A
variational design system completely defines the problem with a series of simultaneous
equations. Thus, it offers greater flexibility by removing restrictions on interdependencies and
solves all the values at once. If engineers change any type of condition or vary any design
parameter, the variational design system can still adjust all other design parameters to arrive at a
new solution that accounts for interactions among all the conditions defined.
9
A word about rapid prototyping is appropriate here. Prior to full-scale production, most
manufacturers produce multiple prototypes in order to see and touch a part directly, to hold and
examine the thing without recourse to abstract geometry. This step can involve significant time
and cost.
Technology has been and is continuing to be introduced that reduces this time and cost
substantially. The original technology is termed stereolithography but other approaches such as
fused deposition modeling (Figure 3) have also appeared. In all cases, systems utilize the
geometry from a CAD model as the starting point. Typically, the model is then mathematically
sliced to obtain the geometry at a given elevation. Material is then deposited, layer by layer, to
build the physical model.
10
Voice input is likely to become practical in this decade. The user can then enter
commands to a CAD/CAM system by voice as opposed to keyboard, mouse, tablet, and other
input forms.
In a virtual reality system, the user is placed within the environment of the computer
visualization. An architect can walk around inside a virtual building that is being designed. An
NC programmer can "walk" along a tool path. A doctor can explore a patient's heart before
surgery. In virtual reality, one can directly manipulate the simulation by grasping, moving, and
changing elements of the simulation with a gloved hand. This may be the ultimate intuitive user
interface.
Contoured Surfaces:
A pair of plastic speaker grilles for portable radios demonstrates the strategic value of
Beach's integrated manufacturing capability. These grilles feature a curved surface that flows
smoothly across the face of the radio and merges into its case. The clean, sweeping lines were an
essential aesthetic element of this design.
Achieving the smooth surface contour and having it cleanly blend into the contour lines
of the case were the prime challenges in designing and building the mold set. The finished grille,
after shrinkage, had to have dimensional tolerances within a [+ or -]0.002-inch band around the
entire curved periphery for easy assembly and an acceptable fit. Without CAD/CAM, these
objectives could not be met (Figure 1).
Phil Kiesler, Chief Engineer, and Gary Wilson, CAD Manager, recall that the original
drawing received in the request for a quote did not contain detailed dimensioning. Several points,
radii, and matching curves were described and detailed, but smooth blending of surfaces was left
to this mold shop.
The design work was done on a Calma CAD system by starting with the defined
dimensional data and then using a series of splines and Bezier curves (curves drawn through
points so no sharp junctures or cusps appear where they meet). One spline line must flow
smoothly into the next. It turned out that this was no small task, because the rate of curvature
slightly changes across the face of the grilles. In addition, blending had to be smooth in all
directions. To make matters worse, the original specification called for hundreds of holes in each
grille that had to be normal to the surface of the workpiece. The pattern easily could be defined,
11
but some sophisticated math routines were needed to orient each one normal to the grille surface.
This orientation would also greatly increase the mold cost. After a discussion, the customer
agreed that the holes could be parallel. Again, the computer assisted in working out the various
patterns for study and comparison.
The design database was generated in about four days, but it was only the beginning. The
design showed the final shape of the workpiece and gave a thorough description of it in
coordinate axes dimensions. But two mold halves also were needed, with the appropriate cavity,
mounting surfaces, ejector pins, coolant connections, plastic flow channels, and all the other
features inherent in the complete mold set.
One of the principal considerations in plastic mold design is allowing for shrinkage.
Although some mathematical routines can be worked out, they are not infallible. There is no
substitute for experience in this area. Plastic shrinkage during cooling is not the only problem. A
decision had to be made about machining the critical cavity areas. Mr. Wilson and Mr. Kiesler
chose to machine all mold elements except for finishing the cavity, then use ram EDM to finish.
The cavity, in 420 stainless steel, was roughed out to within 1/16 inch of its finish dimension,
and then hardened. It was then turned over to the ram EDM unit for the final finish cut.
Individual NC part programs had to be generated to rough the mold cavity, machine the EDM
electrode, and even machine a prototype part for visual inspection and checking. Working from
the basic design resident in the CAD computer, Mr. Wilson entered the desired machining
sequence (the logical sequence of machining operations), the tooling that was to be used, and the
offsets and shrinkage factors that were critically important. For example, EDM requires an offset
to allow for the dielectric fluid and spark gap. It must be stated in the proper direction for either
the male or female half of the mold. When using a ball nose milling cutter to rough out a cavity,
the cusp height allowances must be stated to leave enough material for the finish cuts.
Applications of CAD:
Computer Aided Design (CAD) is a type of computer-based tool used for drafting and
designing. CAD is useful in various designing fields such as architecture, mechanical and
electrical fields being some of them. This is a type of software, which enables users to create
rapid and precise drawings and rough sketch plans of main products. It provides a flexible
pattern in the drawing process that users can alter as according to their required dimensions with
12
minimal efforts.
CAD is not only made for artists specifically but has the diversity to entertain all kinds of
designing enthusiasts. This software has all built in features as per users need and come with
many templates and symbols, for designing and drafting purposes, which gives it a wide area of
application. It is the primary geometry-authoring tool used for all 2D and 3D designing purposes.
It is useful for engineers, architects, and other designing professions.
CAD is applied in mechanical, automotive, aerospace, consumer goods, machinery, and
shipbuilding applications. In this field, it is used for designing various machinery and tools that
are useful for manufacturing purposes. In the field of electronics, it is used in manufacturing
process planning, digital circuit design, and other software applications. In the field of
architecture, it is used as an effective tool for designing all types of buildings and assessing the
integrity of steel-framed buildings. It enables them to design buildings in 2D and 3D models to
give almost a real replica of the original work. It is useful in engineering processes in conceptual
design, and laying out and analyzing components in manufacturing methods. Computer Aided
Software Applications are now available on personal computers to facilitate users to work from
home.
Many professionals use the CAD software because of its precise and creative benefits.
Lower product development costs and reduced design cycles are some other attributes of the
CAD software. Many educational institutions are nowadays indulging in teaching CAD to their
students to make them aware of the latest technological advancement in the field of designing.
Computer Aided Design provides detailed information on Computer Aided Design, Computer
Aided Design Software, Computer Aided Design and Manufacturing, Computer Aided Design
and Engineering and more. Computer Aided Design is affiliated with Cam and Computer Aided
Design.
Softwares in Use:
Based on the concept of CAD technology, many CAD software have been developed by
software giants like Auto-desk Inc, Bentley, Dassult Systemes, Some of the leading software in
the industry are Auto-CAD, Micro-station, CATIA, Pro-Engineer, Uni-graphics, Solid-Edge,
STAAD Pro, Auto-Civil, Auto-desk Inventor and the list goes on and on.
13
Due to CAD facilities, the repetition of work are minimized, exact accuracy can be
achieved; reproduction is not a problem now days. After conversion into digital format it can
also be sent through electronic mail to any part of the world as an editable file. Due to
availability of a lot of file formats, the same file can be opened and used in a variety of CAD
software.
Area of Use:
As it is easy to work with cad software the authorities, engineers, draughts- men in many
part of the world have already begun to work with the most advanced facilities and technologies
like CAD (Computer Aided Designing) for creation, modification, reproduction, safely store and
enhancement of dynamism in their drawings, such as: Civil Engineering, Mechanical
Engineering, Electrical Engineering, Electronics, Engineering, Architectural Engineering,
Aerospace, Automobile, Manufacturing, Production, Plumbing, Piping, HVAC and Fashion
Design etc...
14
sense of the object. CAD systems also lend themselves to modeling cutaway drawings, in which
the internal shape of a part is revealed, and to illustrating the spatial relationships among a
system of parts.
Other limitations to CAD are being addressed by research and development in the field of
expert systems. This field derived from research done on artificial intelligence. One example of
an expert system involves incorporating information about the nature of materials—their
weight, tensile strength, flexibility, and so on—into CAD software. By including this and
other information, the CAD system could then "know" what an expert engineer knows when that
engineer creates a design. The system could then mimic the engineer's thought pattern
and actually "create" a design. Expert systems might involve the implementation of more
abstract principles, such as the nature of gravity and friction, or the function and relation of
commonly used parts, such as levers or nuts and bolts. Expert systems might also come to
change the way data is stored and retrieved in CAD/CAM systems, supplanting the hierarchical
system with one that offers greater flexibility.
One of the key areas of development in CAD technologies is the simulation of
performance. Among the most common types of simulation are testing for response to stress and
modeling the process by which a part might be manufactured or the dynamic relationships
among a system of parts. In stress tests, model surfaces are shown by a grid or mesh, that distort
as the part comes under simulated physical or thermal stress. Dynamics tests function as a
complement or substitute for building working prototypes. The ease with which a part's
specifications can be changed facilitates the development of optimal dynamic efficiencies, both
as regards the functioning of a system of parts and the manufacture of any given part. Simulation
is also used in electronic design automation, in which simulated flow of current through a circuit
enables the rapid testing of various component configurations.
The processes of design and manufacture are, in some sense, conceptually separable. Yet
the design process must be undertaken with an understanding of the nature of the production
process. It is necessary, for example, for a designer to know the properties of the materials with
which the part might be built, the various techniques by which the part might be shaped, and the
scale of production that is economically viable. The conceptual overlap between design and
manufacture is suggestive of the potential benefits of CAD and CAM and the reason they are
generally considered together as a system.
15
Recent technical developments have fundamentally impacted the utility of CAD/CAM
systems. For example, the ever-increasing processing power of personal computers has given
them viability as a vehicle for CAD/CAM application. Another important trend is toward the
establishment of a single CAD-CAM standard, so that different data packages can be exchanged
without manufacturing and delivery delays, unnecessary design revisions, and other problems
that continue to bedevil some CAD-CAM initiatives. Finally, CAD-CAM software continues to
evolve on a continuing basis in such realms as visual representation and integration of modeling
and testing applications.
16
Instead of a line of ink on paper, a line of glowing phosphorus appears on a video console.
Through a series of programmed commands, the drafter can produce finished drawings in much
less time and of a higher quality than those produced manually.
People frequently call CAD systems word processors for drafters. And, in fact, many of
the word processor's advantages find counterparts in CAD systems. John Murray, an engineer
with General Motors, jokes that, as with word processing equipment, "one of the things that
works the best is the eraser." An error on the computer screen can easily be corrected with a few
keystrokes. To correct a manual drawing takes much longer. To simplify this process still
further, some of the more advanced CAD software packages are programmed to detect errors
during the drafting process and inform the user that the data or design is incorrect. Most CAD
systems, irrespective of the particular industry for which they are developed, offer four basic
functions that greatly enhance the productivity of the drafter or designer.
* Replication--the ability to take part of an image and use it in other areas when the design or
drawing has repetitive features;
* Translation--the ability to transfer features from one part of the screen to another;
* Scaling--the ability to change the size of one part of the design in relation to another;
* Rotation--the ability to turn the design on the screen so that it can be examined from different
angles and perspectives.
When drafters and designers do their work on a CAD system, the drawings are stored in a
central data base. The advantages here are several. First, the handy reference to previous
drawings enables the operator to recall and modify a design whose features closely resemble a
present assignment rather than start from scratch. Secondly, the data base encourages
communication between the design and production staff. Working from the same data will
greatly reduce the paper flow within a factory or office. Several sources interviewed for this
article referred to the paperless factory of the future that CAD will permit. Thirdly, these stored
designs serve as the basis for more complex applications of computer-aided design. These
applications generally fall under another acronym--CAE--or computer- aided engineering. Using
the same hardware that is used to draft a design, engineers are able to subject these designs to a
battery of tests and analyses. The computer enables the engineer to simulate a variety of
17
conditions or stresses to which a product may be subjected. For example, a designer or drafter in
the automotive industry may design an axle according to an engineer's rough sketch. The
engineer, working at another computer work station, will subject the axle to varying
combinations of simulated conditions and weights. These computer simulations can cut the time
between design and production; under older technologies, an actual prototype of the product or
part would be fabricated, tested, redesigned, and reproduced until the engineer was satisfied with
its performance. This reduction in development time should decrease costs and increase
productivity.
18
COMPUTER AIDED MANUFACTURING (CAM):
Computer-aided manufacturing (CAM) is the use of computer-based software tools that
assist engineers and machinists in manufacturing or prototyping product components and tooling.
Its primary purpose is to create a faster production process and components and tooling with
more precise dimensions and material consistency, which in some cases, uses only the required
amount of raw material (thus minimizing waste), while simultaneously reducing energy
consumption. CAM is a programming tool that makes it possible to manufacture physical models
using computer-aided design (CAD) programs. CAM creates real life versions of components
designed within a software package. CAM was first used in 1971 for car body design and
tooling.
Overview:
Traditionally, CAM has been considered as a numerical control (NC) programming tool wherein
three-dimensional (3D) models of components generated in CAD software are used to generate
CNC code to drive numerically controlled machine tools.
Although this remains the most common CAM function, CAM functions have expanded
to integrate CAM more fully with CAD/CAM/CAE PLM solutions. As with other “Computer-
Aided” technologies, CAM does not eliminate the need for skilled professionals such as
Manufacturing Engineers and NC Programmers. CAM, in fact, both leverages the value of the
most skilled manufacturing professionals through advanced productivity tools, while building the
skills of new professionals through visualization, simulation and optimization tools.
Historical shortcomings:
Historically, CAM software was seen to have several shortcomings that necessitated an overly
high level of involvement by skilled CNC machinists. Fallows created the first CAM software
but this had severe shortcomings and was promptly taken back into the developing stage. CAM
19
software would output code for the least capable machine, as each machine tool interpreter added
on to the standard g-code set for increased flexibility. In some cases, such as improperly set up
CAM software or specific tools, the CNC machine required manual editing before the program
will run properly. None of these issues were so insurmountable that a thoughtful engineer could
not overcome for prototyping or small production runs; G-Code is a simple language. In high
production or high precision shops, a different set of problems were encountered where an
experienced CNC machinist must both hand-code programs and run CAM software.
20
■Ease of Use
Manufacturing complexity
The manufacturing environment is increasingly complex. The need for CAM and PLM tools by
the manufacturing engineer, NC programmer or machinist is similar to the need for computer
assistance by the pilot of modern aircraft systems. The modern machinery cannot be properly
used without this assistance.
Today's CAM systems support the full range of machine tools including: turning, 5 axis
machining and wire EDM. Today’s CAM user can easily generate streamlined tool paths,
optimized tool axis tilt for higher feed rates and optimized Z axis depth cuts as well as driving
non-cutting operations such as the specification of probing motions.
21
from a stand-alone CAM system to a fully integrated multi-CAD 3D solution-set. These
solutions are created to meet the full needs of manufacturing personnel including part planning,
shop documentation, resource management and data management and exchange.
Machining Process:
Most machining progresses through four stages, each of which is implemented by a
variety of basic and sophisticated strategies, depending on the material and the software
available. Those stages are:
Roughing: This process begins with raw stock, known as billet, and cuts it very roughly to shape
of the final model. In milling, the result often gives the appearance of terraces, because the
strategy has taken advantage of the ability to cut the model horizontally. Common strategies are
zig-zag clearing, offset clearing, plunge roughing, rest-roughing.
Semi-finishing: This process begins with a roughed part that unevenly approximates the model
and cuts to within a fixed offset distance from the model. The semi-finishing pass must leave a
small amount of material so the tool can cut accurately while finishing, but not so little that the
tool and material deflect instead of shearing. Common strategies are raster passes, waterline
passes, constant step-over passes, pencil milling.
Finishing: Finishing involves a slow pass across the material in very fine steps to produce the
finished part. In finishing, the step between one pass and another is minimal. Feed rates are low
and spindle speeds are raised to produce an accurate surface.
Contour milling: In milling applications on hardware with five or more axes, a separate finishing
process called contouring can be performed. Instead of stepping down in fine-grained increments
to approximate a surface, the workpiece is rotated to make the cutting surfaces of the tool tangent
to the ideal part features. This produces an excellent surface finish with high dimensional
accuracy.
22
Computer Aided Manufacturing Software:
Computer Aided Manufacturing (CAM) is one of the software automation processes that
directly convert the product drawing or the object into the code design, enabling the machine to
manufacture the product. The CAM system is used in various machines like lathes or milling
machines for product manufacturing purposes. It allows the computer work instructions to
communicate directly to the manufacturing machines. This saves on time and money, in that the
controls can all be routed directly to a computer or laptop system, where changes can be made
with the click of a button.
It provides compatibility with any CAD file format including DXF, DWG and DGN
Professional 2D Mechanical drafting and design. It allows easy 3D modeling and rendering
options. The CAM software provides complete support for milling, drilling and lathing
operations. It includes the setup wizard, the tool database and a dialog-free CAM palette. CAM
software has developed in such a way that it has become quick, flexible machining with effective
simulation. The 2D and 3D simulation is developed in the real time environment - a major
advantage of the software. Load factor compensation for machine and tool, tool paths, automatic
optimal tool paths and cumulative time are also major benefits in this CAM software.
Several software vendors like AutoDesk, EDC, PTC, GibbsCAM and CamSoft offer you
the software with factors involving high quality, ease of use, and a reasonable price. EDS e-
factory, EDS e-Vis, EDC FactoryCAD, PTC Pro/ENGINEER Advanced Assembly, and the API
Toolkit are a few of the major software applications that are used in the CAM system.
Computer Aided Manufacturing provides detailed information on Applications of
Computer Aided Manufacturing, Cam And Computer Aided Design, Computer Aided Design,
Computer Aided Design Scanners and more. Computer Aided Manufacturing is affiliated with
Computer Aided Design and Manufacturing.
CAD stands for Computer Aided Design, it used to stand for Computer Aided Drafting
but was changed because as it improved, it evolved to do more than just drafting. It is also
known as CAID - Computer Aided Industrial Design and CAAD - Computer Aided
Architectural Design.
CAD can be used in a number of different ways, depending on the task at hand, the
profession of the user, as well as the type of software that is run. CAD comes in a variety of
systems, and each requires a different pattern of thought on how to use it to maximum benefit. In
23
addition, each system's virtual components must also be designed in a different way.
CAD generally operates on computers that are Windows based, although some systems
run on hardware that uses Unix operating systems and a few work with Linux. There are a few
CAD systems e.g. Ocad and NX that provide multi-platform support and these include Windows,
Linux, UNIX, and Mac OSX.
In order to use CAD it is generally not necessary to obtain any special hardware other
than a high-end OpenGL based Graphics card. If you are going to be doing complex designs then
you will need computers with high speed CPUs and large amounts of RAM. A computer mouse
is used as the human-machine interface, although a pen and digitising graphics tablet can also be
used. In the 21st century technology has expanded its wings in almost every sphere of knowledge
and life style. Hence with the enhancement of technology has empowered Engineers and
Designers to get the power to excel with CAD.
Due to the advancement of CAD (computer aided design) there is no painstaking workout
of the engineers and draughts-men standing near the drawing board with a huge drafter and
trying to draw their concepts.
Recreation of designs & drawings has become so easy today that it takes only an
unimaginable fraction of a second. Sharing of a single platform helps the draughts man to divide
the time consumption and hence increases the productivity.
24
■WorkNC from Sescoi
Other CAM products and companies are BobCAD, CAMWorks from Geometric
Technologies, Inc., Dolphin, ESPRIT from DP Technology, GCAM, GIBcam, GibbsCAM,
MazaCAM, MetaCAM,OneCNC, SUM3D, SurfCAM, T-FLEX, TopSolid from Missler and
VisualMILL from MecSoft.
Areas of usage
■Aerospace Engineering
■Automotive Engineering
■Mechanical Industries
■electronic design automation, CAM tools prepare printed circuit board (PCB) and integrated
circuit design data for manufacturing.
25
of a company's operations.
While mechanical applications of CAD account for nearly one-half of the systems sold
today, other industries recognize the benefits it affords. For the electronics industry, CAD offers
considerable advantages, particularly in the design on printed circuit boards and integrated
circuits. The design of these components can be tedious and time consuming. And so many lines
and cross lines must be drawn that errors are not easily detected. CAD not only speeds up the
drawing but detects errors as well.
Architecture, engineering, and construction applications offer the greatest potential for
growth in sales, according to a recent industry survey. Although the construction and electronics
industries each represent about 16 percent of the CAD market now, the penetration is far less
extensive. However, both simple drafting applications and more complex design and analysis are
evident within the industry. Architectural drafters will be able to complete drawings of a higher
quality in much less time. Architects and engineers will be able to submit their designs to more
exhaustive structural and stress analyses. Piping and electrical layouts will be made easier and
the design and allocation of interior space will be facilitated as well. As a management tool, the
data base created during the project will provide an effective means of inventory control enabling
contractors not only to speed construction but to reduce costs.
CAD is also having an impact upon cartography. Geographers use CAD systems to help
them draft maps used for environmental impact analysis and land use planning and for charting
landfill contours for strip mining. Some software packages are available that aid in
extraterrestrial mapping.
Process industries, such as oil and gas refineries and chemical manufacturers, as well as
power and utility companies, must plan, construct, operate, and maintain electrical grid and
pipeline networks. CAD makes these complex tasks easier. CAD even has applications in
landscape design, interior design, and fashion design. Some high fashion couturiers use CAD
systems to lay out patterns on expensive fabrics as a way to minimize waste.
Implications for Employment
Technological innovations invariably prompt questions as to how these changes will affect
employment. Implicit in many of these questions is the notion that the introduction of new
technologies will lead to the elimination of certain jobs or at least to significant changes in the
way these jobs will be performed. Among those occupations directly affected by CAD, concerns
26
focus upon drafting and design jobs.
Drafting shops are traditionally a bottleneck in many industries. Pen and ink drawings
take a long time to produce. Once complete, the drawings must be presented to the engineer or
architect for review and analysis. The ability of CAD systems to produce drawings much faster
than manual techniques would seem to reduce the need for drafters in the long run. Dr. Donald
Hecht, president of the California College of Technology in Anaheim, a technical school that
trains students in computer-aided design and drafting, urges a more cautious appraisal. "I hesitate
to make such straight-line predictions," he says, "particularly when dealing with computer-based
technologies." Hecht believes that the reduction in drafting time and the consequent increases in
productivity that CAD affords may foster a greater emphasis upon new product design and
development.
27
CATIAP3V5
Introduction:
CATIA (Computer Aided Three-dimensional Interactive Application) is a multi-platform
CAD/CAM/CAE commercial software suite developed by the French company Dassault
Systemes and marketed worldwide by IBM. Written in the C++ programming language, CATIA
is the cornerstone of the Dassault Systemes product lifecycle management software suite.
CATIA competes in the CAD/CAM/CAE market with Siemens NX, Pro/ENGINEER, Autodesk
Inventor and SolidEdge.
Several thousands of companies in multiple industries Worldwide have already chosen
the Virtual Design capabilities of CATIA products to ensure their products Real Success. CATIA
delivers solutions for the enterprise from large OEMs through their supply chains to Small and
Medium Businesses.
CATIA V5 is the leading solution for product excellence. It addresses all manufacturing
organizations, from OEMs, through their supply chains, to small independent companies. The
range of CATIA V5’s capabilities allows for its application in a wide variety of industries, from
aerospace, automotive, industrial machinery, electrical, electronics, shipbuilding, plant design,
and consumer goods, to jewelry and clothing.
CATIA V5 is the only solution that covers the complete product development process,
from product concept specifications through to product-in-service, in a fully integrated manner.
Based on an open, scalable architecture, it facilitates true collaborative engineering across the
multidisciplinary extended enterprise, including style and form design, mechanical design,
equipment and systems engineering, digital mock-up management, machining, analysis, and
simulation. By enabling enterprises to reuse product design knowledge and accelerate
development cycles, CATIA V5 helps companies speed-up their response to market needs.
In conjunction with ENOVIA for collaborative product lifecycle management, SIMULIA
for engineering quality and DELMIA for production performance, CATIA V5 is a key
component of V5 PLM.
28
Features:
Commonly referred as a 3D Product Lifecycle Management software suite, CATIA
supports multiple stages of Product development (CAx), from Conceptualization, Design (CAD),
Manufacturing (CAM), and Engineering (CAE).
CATIA can be customized via application programming interfaces (API). V4 can be
adapted in the Fortran and C programming languages under an API called CAA. V5 can be
adapted via the Visual Basic and C++ programming languages, an API called CAA2 or CAA V5
that is a component object model (COM)-like interface. Although later versions of CATIA V4
implemented NURBS, V4 principally used piecewise polynomial surfaces. CATIA V4 uses a
non-manifold solid engine.
CatiaV5 features a parametric solid/surface-based package which uses NURBS as the
core surface representation and has several workbenches that provide KBE support. V5 can work
with other applications, including Enovia, Smarteam, and various CAE Analysis applications.
The version used in the current project is CATIA V5R17. It extends the unique 2D/3D
associative approach for conceptual design and extends the 3D master approach by enabling the
fast and convenient display of product information, such as tolerances and annotations, in a
familiar drawing layout within the 3D environment. It boosts conceptual design within the 3D
environment by enabling designers to easily create in-context 2D sketches from the automatic
detection of existing 3D geometry displayed in the view background. Efficient, comprehensive,
and standards-compliant CATIA V5 drafting capabilities always guarantee high quality when
realizing drawing layouts and dress-up, whether immersed in 3D or in a separate drawing
document. It is continually enhanced and updated to meet specialized needs, such as support for
new customized symbols, strokes, and open-type fonts.
CATIA V5R17 promotes 3D as the master reference for part and product definition.
Designers can define and manage standards-compliant tolerance specifications and annotations
linked to the 3D geometry, making them directly reusable for manufacturing planners and to be
shared throughout the enterprise. Designers can easily present and share 3D tolerancing and
annotation in a familiar drawing layout embedded in the 3D environment. V5R17 enables the
rapid creation of associative views from Functional Tolerancing & Annotation views or captures.
Users benefit from a more productive 3D annotation definition and layout process by realizing
29
specific operations in a single step, such as directly managing the view ratio property for 3D
annotation.
30
Notable Industries using CATIA:
CATIA is widely used throughout the engineering industry, especially in the automotive and
aerospace sectors.
Aerospace:
The Boeing Company used CATIA V3 to develop its 777 airliner, and is currently using
CATIA V5 for the 787 series aircraft. They have employed the full range of Dassault Systemes'
3D PLM products — CATIA, DELMIA, and ENOVIA LCA — supplemented by Boeing
developed applications.[9] Chinese Xian JH-7A is the first aircraft developed by CATIA V5,
when the design was completed on September 26, 2000. European aerospace giant Airbus has
been using CATIA since 2001.[10] Canadian aircraft maker Bombardier Aerospace has done all
of its aircraft design on CATIA.[11] The Brazilian aircraft company, EMBRAER, use Catia V4
and V5 to build all airplanes. The British Helicopter company, Westlands, use CATIA V4 and
V5 to produce all their aircraft. Westlands is now part of an Italian company called Finmeccanica
the joined company calls themselves AgustaWestland.
Automotive:
Many automotive companies use CATIA to varying degrees, including BMW, Porsche,
Daimler AG, Chrysler, Audi,[12] Volkswagen, Bentley Motors Limited, Volvo, Fiat, Benteler
AG, PSA Peugeot Citroën, Renault, Toyota, Ford, Scania, Hyundai, Škoda Auto, Tesla Motors,
Proton, Tata motors and Mahindra & Mahindra Limited. Goodyear uses it in making tires for
automotive and aerospace and also uses a customized CATIA for its design and development.
Many automotive companies use CATIA for car structures — door beams, IP supports, bumper
beams, roof rails, side rails, body components — because CATIA is very good in surface
creation and Computer representation of surfaces.
Shipbuilding:
Dassault Systems has begun serving shipbuilders with CATIA V5 release 8, which
includes special features useful to shipbuilders. GD Electric Boat used CATIA to design the
latest fast attack submarine class for the United States Navy, the Virginia class.[13] Northrop
Grumman Newport News also used CATIA to design the Gerald R. Ford class of supercarriers
for the US Navy.[14]
31
Other:
Architect Frank Gehry has used the software, through the C-Cubed Virtual Architecture
company, now Virtual Build Team, to design his award-winning curvilinear buildings.[15] His
technology arm, Gehry Technologies, has been developing software based on CATIA V5 named
Digital Project.[16] Digital Project has been used to design buildings and has successfully
completed a handful of projects.
32
MASTERCAM
History:
Founded in Massachusetts in 1983,[1] CNC Software, Inc. is one of the oldest
developers of PC-based computer-aided design / computer-aided manufacturing (CAD/CAM)
software. They are one of the first to introduce CAD/CAM software designed for both
machinists and engineers.
Introduction:
Mastercam, CNC Software’s main product, started as a 2D CAM system with CAD
tools that let machinists design virtual parts on a computer screen and also guided computer
numerical controlled (CNC) machine tools in the manufacture of parts. Since then, Mastercam
has grown into the most widely used CAD/CAM package in the world.[2] CNC Software, Inc. is
now located in Tolland, Connecticut.
Mastercam’s comprehensive set of predefined toolpaths—including contour, drill,
pocketing, face, peel mill, engraving, surface high speed, advanced multiaxis, and many more—
enable machinists to cut parts efficiently and accurately. Mastercam users can create and cut
parts using one of many supplied machine and control definitions, or they can use Mastercam’s
advanced tools to create their own customized definitions.
Mastercam also offers a level of flexibility that allows the integration of 3rd party
applications, called C-hooks, to address unique machine or process specific scenarios.
Mastercam's name is a double entendre: it implies mastery of CAM (computer-aided
manufacturing), which involves today's latest machine tool control technology; and it
simultaneously pays homage to yesterday's machine tool control technology by echoing the older
term master cam, which referred to the main cam or model that a tracer followed in order to
control the movements of a mechanically automated machine tool.
33
previous version and adopted a true Windows application feel. Mastercam supports many types
of machines, each with a choice of levels of functionality, as well as offers optional add-ins for
solid modeling, 4-axis machining, and 5-axis machining. The following list describes the
Mastercam product levels:
• Design—3D wireframe geometry creation, dimensioning, importing and exporting of
non-Mastercam CAD files (such as AutoCAD, SolidWorks, Solid Edge, Inventor,
Parasolid, etc.).
• Mill Entry—Includes Design, plus various toolpaths (top construction and tool planes
only), posting, backplot, verify.
• Mill, Level 1—Includes Mill Entry, plus surface creation, many additional toolpaths
(for all construction and tool planes), highfeed machining, toolpath editor, toolpath
transforms, stock definition.
• Mill, Level 2—Includes Mill, Level 1, plus additional toolpaths, toolpath projection,
surface rough and finish machining, surface pocketing, containment boundaries, check
surfaces.
• Mill, Level 3—Includes Mill, Level 2, plus 5-axis wireframe toolpaths, more
powerful surface rough and finish machining, multiaxis toolpaths.
• 5-Axis add-on—5-Axis roughing, finishing, flowline multisurface, contour, depth
cuts, drilling, advanced gouge checking.
• Lathe Entry—3D wireframe geometry creation, dimensioning, importing and
exporting of non-Mastercam CAD files (such as AutoCAD, SolidWorks, Solid Edge,
Inventor, Parasolid, etc.), various toolpaths, backplot, posting.
• Lathe, Level 1—Includes Lathe Entry, plus surface creation, C-axis toolpaths, stock
definition, stock view utility.
• Router Entry—3D wireframe geometry creation, dimensioning, importing and
exporting of non-Mastercam CAD files (such as AutoCAD, SolidWorks, Solid Edge,
Inventor, Parasolid, etc.), various toolpaths (top construction and tool planes only),
toolpath transformation in top plane, backplot, verify, posting. CNC
Software/Mastercam 2
34
• Router—Includes Router Entry, plus surface creation, rectangular geometry nesting,
additional toolpaths (for all construction and tool planes), highfeed machining,
toolpath editor, full toolpath transformations, stock definition.
• Router Plus—Includes Router, plus additional toolpaths, toolpath projection, surface
rough and finish machining, surface pocketing, containment boundaries, check
surfaces.
• Router Pro—Includes Router Plus, plus True Shape geometry nesting, 5-axis
toolpath functionality, multiple surface rough and finish machining, multiaxis
toolpaths, toolpath nesting.
• Wire—2D and 3D geometry creation, dimensioning, various 2-axis and 4-axis
wirepaths, customizable power libraries, tabs.
• Art—Quick 3D design, 2D outlines into 3D shapes, shape blending, conversion of
2D artwork into machinable geometry, plus exclusive fast toolpaths, rough and finish
strategies, on-screen part cutting.
The Router products are targeted to the woodworking industries but are virtually identical to the
Mill line.
CNC Programming:
Programming is a means of defining Tool Movements, through the application of coded Letter
Symbols. As shown in the figure, all the phases of production are included in the programming,
beginning with the technical drawing and end with the final product.
CNC machines use a special programming language called GN-code (technical name:
RS274). MasterCAM is a software that allows users to create GN-code programs that can be
used to cut different geometric shapes on CNC machines. The main functions are:
35
(i) Describe the geometry of the part to be machined.
(ii) Create a tool database – this DB carries information about the available milling
tools.
(iii) Create the GN-code program to cut the part.
(iv) Simulate the machining of the part (for visual verification of the program).
(v) Upload the program to the CNC machine controller.
36
Virtual Machining Process
Before commencement of the actual machining, the followings steps need to be considered and
performed carefully.
1) Drawing Study:
Drawing study is the very first basic and important step of manufacturing. It is the
process of understanding the components geometry, identifying the machining processes and
knowing various other parameters which are all together required to convert that component
from raw material to final finished product. Also special processes like coatings, polishing
finishes etc. are all identified. Drawings are normally represented in sheets of ‘A’-series. Based
on the size & geometry of the part, no of details, other specifications, etc., the ‘A’ sheet is used
to represent it. Sometimes, based on the complexity of the part geometry, more than one sheet
will also be used to provide all the details. Any mistake or error if arises while reading or
understanding the drawing, it ruins the entire manufacturing process and finally the part gets
rejected. So, one should have proper technical knowledge and sufficient experience for reading
and understanding a Production Drawing. These drawings are generally read by Production In-
charges or Shop floor Supervisors.
37
2) Development of Geometry CAD Model:
You can create the geometry in one of two ways:
(a) By using the graphical design interface provided by MasterCAM
(b) By making the design in a CAD software, e.g. CATIA, Pro/Engineer,
SolidWorks, and saving it in a format that MasterCAM can import (safest format
to use: IGES; other possible formats include STL, STEP)
Method (a) is useful if you want to cut a simple shape; although MasterCAM provides some
functions to generate 3D curved surfaces, defining the geometry in this environment is not
convenient. So: if you want to make a part where the entire shape is defined using volumes made
by sweeping 2D profiles normal to the plane of the geometry, use method (a). If you have access
to any CAD system, use method (b).
Method (b) generates the part by using a CAD system, and saved in any one of the Data
Exchange Formats. Design the part (in, e.g. CATIA or SolidWorks). It is best if you already
create the part such that the surfaces to machine are in the correct orientation and position for the
machine. That is, the machining surfaces should be accessible from –Z direction, and the part
should be located such that the covering, rectangular stock should be in the positive octant of the
coordinate frame, with the corner at the origin.
In the current project, the model is developed using Catia V5R17.
39
4) Planning of Tools (Tooling):
For the completion of a machining process in-time and with desired surface finish
conditions, proper planning of the required tools must be adopted. After identifying the processes
involved, we need to select which tools are suitable for each individual process. This planning of
tools not only helps to complete the operation in-time, but also brings down the manufacturing
cost to a greater extent. If the jobs to produced are of large quantity (e.g. nuts, bolts, automobile
components, etc), then it is advisable to use indexable milling inserts, because inserts can
machine more number of parts when compared to solid cutters. This automatically, reduces the
tooling expenses.
The tool database present in the Mastercam software describes the geometry of tools
available for use in the workshop. The path that a tool travels in order to cut a shape depends on
the size of the tool; some other information about the tool is also important – for example, the
length of the cutting teeth on a drill or an end mill constraints the depth of the hole these can cut.
The main functions for the tool database are:
(i) Look for an existing tool that you may want to use
MAIN MENU NC Utils Def. Tools Library
The Tools Manager window comes up, listing all available tools. Suppose we want to
look for a flat end-mill of small diameter (e.g. less than 6mm). We can use the filter as follows:
Click Filter. In the Tools list Filter window, click Endmill1 Flat (top left icon) [if you leave the
mouse cursor above the icon, its name appears] Tool diameter: [less than] value: 6 Unit
masking: metric OK.
The tools Manager window will show all tools that match these criteria.
NOTE: by default, ALL TOOL TYPES are selected; you must click on each icon to DE-
SELECT it.
The figure below shows that my search gave five tools matching my criteria; If I want to
use a 5mm end mill, double click on this tool, and its details will be shown in a Define Tool
window.
If the search results in no existing tool, and you would like to enter the data of a tool you have
into the library: RIGHT-CLICK within the Tools Manager window Create new tool. This also
pops up the Define Tool window; type the data for the new tool, and click Save to library...
40
Figure 5.4: Schematics of Various Types of Cutting Tools.
In the current case, for all the four operations, Flat-End Mill type cutters of different radii
are used.
5) Generation of Machining Tool path:
There are many different options and settings in generation of the tool path. Respective
option must be chosen based on the requirement.
Using the Tool parameters tab, you can set the Spindle speed, Feed rate and Plunge rate;
if you know the values, enter them; otherwise just use the default – you can modify these when
you actually machine the part, on the CNC machine.
Hit OK, and if all goes well, the software will generate the tool path for you, and display
it. Notice that the tool path where it is cutting is shown in different color than when it is moving
up or down, and moving between pockets. Also notice how the tool path for removing the region
inside the pocket is zig-zag, but the tool path also goes once around the contour of each pocket.
41
Figure 5.5: Graphical View of the Virtually Machined Component.
42
8) Completion of the Given Task:
Following all the above operations properly with proper attention and care leads
to completion of the task as per the specifications. After completion of all these steps, the NC
code part programme must be developed for real time machining.
The tool path generated by MasterCAM has all information required to control a CNC
machine tool to cut the part. However, different CNC machines use slightly different versions of
GN-code. The conversion of the machining data to the GN-code specific for a particular CNC
machine is called Post-Processing. The exact format of the GN-code is stored in different post-
processing files, and the system will use whichever post-processing format you select.
Later, the generated NC-Part file is subjected to proper Header- Footer changes before
being transferred into the CNC machine controller. You can set the communications settings for
your CNC machine controller, and if your PC is connected to the CNC machine controller, the
program will be uploaded to the CNC machine. Else, the program can also be transferred using
various external Data Transfer Devices.
CONCLUSIONS:
As the concept of virtual machining is not just viewing of the machining process
graphically, it has to be carried out with atmost care. So, while performing virtual machining, the
following precautions must be taken into consideration:
No mistake or error should takes place while creating the model. All the
dimensions and sizes must be maintained as given in the drawing.
The model has to be converted into proper Data Exchange formats in which very
less or no geometry losses occur.
After importing the model into the CAM software, it should be transformed into
proper orientation as per the machining convenience.
While generating the tool paths for various operations, precautions should be
followed keeping in mind, the real time machining hurdles, like spindle speed ,
feed, depth of cut, etc.
It is always advisable that tool path for each operation is verified until you get
visually satisfied.
43
After generating the NC Code part file, it is mandatory that necessary Header-
Footer changes are made before transforming it into the CNC machine controller.
REFERENCES:
1) Operational Manual of “Vertical Milling Machine. Model: BMV 50, Controller: Fanuc Series-
OiMB”.
2) “CNC MACHINES” by B.S. Pabla, M.A. Adhithan.
3) “MECHATRONICS” by HMT.
4) “Automation Production Systems and Computer Integrated Manufacturing” by Mikell P.
Groover.
5) www.wikipedia.com
44