STK403-130 2002.12.

28

TENTATIVE
1. Case Outline 15Pins (See attached Package Outline Diagram)
2. Function 2 channels AF power amplifier
3. Application 100W audio use
4. Maximum Ratings / Ta=25°C
Item Symbol Conditions Ratings Unit
Maximum Power Supply Voltage 0 Vcc max(0) Non- signal +-71.5 V
Maximum Power Supply Voltage Vcc max(1) Signal ,R L≧6ohm +-63 V
Minimum Operation Supply Voltage Vcc min +-10 V
#12 Maximum Operating Current *7 IST OFF max 0.6 mA
Thermal Resistance Theta j-c Per one power TR 1.7 °C/W
Junction Temperature Tj max 150 °C
Should satisfy Tj max and Tc max
Operating Substrate Temperature Tc max 125 °C
Storage Temperature Tstg -30 to +125 °C
Available Time for Load Vcc=+-44V,RL=6ohm,f=50Hz
ts 0.3 s
Short-circuit *4 PO=100W,1ch drive
5. Operating Characteristics
Tc=25°C ,RL=6ohm(Non-inductive Load),Rg=600ohm,VG=30dB
Conditions *2 Ratings
Item Symbol V f Po THD Unit
MIN. TYP. MAX.
(V) (Hz) (W) (%)
Output Power *1 Po 1 +-44 20 to 20k 0.4 96 100 W
Po 2 +-44 1k 10 150
THD 1 +-44 20 to 20k 0.4
THD *1 5.0 VG=30dB %
THD 2 +-44 1k 0.01
Frequency
fL,fH +-44 1.0 +0 -3 dB 20 to 50k Hz
Characteristics *1
Input Impedance ri +-44 1k 1.0 55 kohm
Output Noise
VNO +-53 Rg=2.2kohm 1.0 mVrms
Voltage *3
Quiescent Current ICCO +-53 No load 20 45 80 mA
Output Neutral
VN +-53 -70 0 +70 mV
Voltage
#13 Stand-By V#13=5V
IST ON +-44 0 mA
Current #13PIN
#13 Operating Resistance
IST OFF +-44 R1=13kohm 0.25 0.6 mA
Current

*Specifications and information herein are subject to change without notice.

Sanyo Electric Co.,Ltd. Module Systems Division NO.1

 *Specifications and information herein are subject to change without notice.

Note *1.1channel Operation.

*2.All tests are measured using a constant-voltage supply unless otherwise specified.
*3.The output noise voltage is peak value of an average-reading meter with a rms value scale(VTVM).
A regulated AC supply(50Hz) should be used to eliminate the effects of AC primary line flicker noise.
*4.Available time for load short-circuit and output noise voltage are measured using the specified
transformer power supply.
*5.Please keep the condition always most below Voltage ‘–Pre Vcc(#1pin)’.
*6.In case of heat sink design, we request customer to design in the condition to have assumed market.
*7.Please specify resistance value by satisfying ‘#13(Stand-By)pin’ Maximum Operating Current.
This Circuit change operation mode to give above VBE(about 0.6v) voltage at ‘#13(Stand-By)pin’.
*8.The case of this Hybrid-IC is using thermoplastic adhesive.

Specified Transformer Power Supply

DBA40C 10000u
+Vcc
+
500ohm

+
500ohm
-Vcc
10000u

(Equivalent to MG-250)

Sanyo Electric Co.,Ltd. Module Systems Division NO.2

3

Pre Driver Pre Driver

CH1 CH2

11 15

12 14

Bias Circuit
1

SUB

10 9 5 4 6 7 13
 STK403-090/100/120/130 (*1)Stand-by 端子(#13)の動作時流入電流が最大定格を
越えないよう制限抵抗値を設定して下さい。
Ch1 Ch1 Ch2 Ch2 Ch1 Ch1 ST-BY Ch2 Ch2
-PRE -Vcc +Vcc OUT OUT OUT OUT +PRE SUB GND IN NF NF IN Please specify resistance value by satisfying
’#13(Stand-by)pin’ Maximum Operating Current.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
0.22Ω 0.22Ω
100 100 (*1)
56kΩ pF pF
Stand-by Control
56kΩ
3pF 2.2μF
/50V 1kΩ
Ch2 IN
3pF 1.8kΩ 1.8kΩ

470pF
56kΩ
10μF 10μF
/10V /10V
GND

470pF
56kΩ
Ch1 IN
2.2μF 1kΩ
/50V
3μH

Ch2 OUT
0.1μF
+Vcc
100Ω/1W 100μF 4.7Ω 4.7Ω/1W
100μF /100v
/100V GND
GND
100μF
/100V GND
4.7Ω/1W
3μH
-Vcc 0.1μF
Ch1 OUT
4.7Ω

SUB.GND
ww
w.
sn
ee
ze
.c
o .in
 (*1)Stand-by 端子(#13)の動作時流入電流が最大定格を
越えないよう制限抵抗値 R1 を設定して下さい。
Please specify resistance value by satisfying
STK403-100series ’#13(Stand-by)pin’ Maximum Operating Current.
Ch1 Ch1 Ch2 Ch2 Ch1 Ch1 Ch2 Ch2
-PRE -Vcc +Vcc OUT OUT +PRE SUB GND IN NF ST-BY NF IN
OUT OUT

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1kΩ

0.22Ω 0.22Ω 33kΩ Stand-by Control

100pF 100pF (*1) R1 H：Operation Mode(+5V)
56kΩ 13KΩ
33μF 2kΩ
/10V L：Stand-by Mode(0V)
56kΩ
3pF 2.2μF
/50V 1kΩ
Ch2 IN
3pF 1.8kΩ 1.8kΩ 10kΩ

470pF
56kΩ
10μF 10μF
/10V /10V
GND

470pF
56kΩ
10kΩ
Ch1 IN
2.2μF 1kΩ
/50V
3μH 10kΩ

100Ω/1W Ch2 OUT Mute Control

0.1μF
+Vcc H：Single Mute
4.7Ω 2.2kΩ
100μF 4.7Ω/1W
100μF /100V L：Normal
/100V GND
GND
+5V
100μF
GND Stand-by Control
/100V
4.7Ω/1W
3μH +5V
-Vcc 0.1μF
Mute Control
Ch1 OUT
MUTE
4.7Ω

SUB.GND
ST-BY PLAY MUTE ST-BY