Piston

This article needs additional citations for

verification. Learn more

A piston is a component of reciprocating

engines, reciprocating pumps, gas
compressors, hydraulic cylinders and
pneumatic cylinders, among other similar
mechanisms. It is the moving component
that is contained by a cylinder and is made
gas-tight by piston rings. In an engine, its
purpose is to transfer force from
expanding gas in the cylinder to the
crankshaft via a piston rod and/or
connecting rod. In a pump, the function is
reversed and force is transferred from the
crankshaft to the piston for the purpose of
compressing or ejecting the fluid in the
cylinder. In some engines, the piston also
acts as a valve by covering and uncovering
ports in the cylinder.

Pistons within a sectioned petrol engine

Animation of a piston system.

Piston engines

Piston

Internal combustion engines …

Internal combustion engine piston, sectioned to show
the gudgeon pin.

An internal combustion engine is acted

upon by the pressure of the expanding
combustion gases in the combustion
chamber space at the top of the cylinder.
This force then acts downwards through
the connecting rod and onto the
crankshaft. The connecting rod is attached
to the piston by a swivelling gudgeon pin
(US: wrist pin). This pin is mounted within
the piston: unlike the steam engine, there
is no piston rod or crosshead (except big
two stroke engines).

The typical piston design is on the picture.

This type of piston is widely used in car
diesel engines. According to purpose,
supercharging level and working
conditions of engines the shape and
proportions can be changed.

High-power diesel engines work in difficult

conditions. Maximum pressure in the
combustion chamber can reach 20 MPa
and maximum temperature of some piston
surfaces can exceed 450°C. It is possible
to improve piston cooling by creating
special cooling cavity. Injector supplies
this cooling cavity «A» with oil through oil
supply channel «B». For better temperature
reduction construction should be carefully
calculated and analyzed. Oil flow in the
cooling cavity should be not less than 80%
of the oil flow through the injector.
A – cooling cavity; B – oil supply channel

The pin itself is of hardened steel and is

fixed in the piston, but free to move in the
connecting rod. A few designs use a 'fully
floating' design that is loose in both
components. All pins must be prevented
from moving sideways and the ends of the
pin digging into the cylinder wall, usually
by circlips.
Gas sealing is achieved by the use of
piston rings. These are a number of
narrow iron rings, fitted loosely into
grooves in the piston, just below the
crown. The rings are split at a point in the
rim, allowing them to press against the
cylinder with a light spring pressure. Two
types of ring are used: the upper rings
have solid faces and provide gas sealing;
lower rings have narrow edges and a U-
shaped profile, to act as oil scrapers.
There are many proprietary and detail
design features associated with piston
rings.
Pistons are cast from aluminium alloys.
For better strength and fatigue life, some
racing pistons[1] may be forged instead.
Billet pistons are also used in racing
engines because they do not rely on the
size and architecture of available forgings,
allowing for last-minute design changes.
Although not commonly visible to the
naked eye, pistons themselves are
designed with a certain level of ovality and
profile taper, meaning they are not
perfectly round, and their diameter is
larger near the bottom of the skirt than at
the crown.[2]
Early pistons were of cast iron, but there
were obvious benefits for engine balancing
if a lighter alloy could be used. To produce
pistons that could survive engine
combustion temperatures, it was
necessary to develop new alloys such as Y
alloy and Hiduminium, specifically for use
as pistons.

A few early gas engines[i] had double-

acting cylinders, but otherwise effectively
all internal combustion engine pistons are
single-acting. During World War II, the US
submarine Pompano[ii] was fitted with a
prototype of the infamously unreliable
H.O.R. double-acting two-stroke diesel
engine. Although compact, for use in a
cramped submarine, this design of engine
was not repeated.

Media related to Internal combustion

engine pistons at Wikimedia Commons

Trunk pistons …

Trunk pistons are long relative to their

diameter. They act both as a piston and
cylindrical crosshead. As the connecting
rod is angled for much of its rotation, there
is also a side force that reacts along the
side of the piston against the cylinder wall.
A longer piston helps to support this.
Trunk pistons have been a common
design of piston since the early days of the
reciprocating internal combustion engine.
They were used for both petrol and diesel
engines, although high speed engines
have now adopted the lighter weight
slipper piston.

A characteristic of most trunk pistons,

particularly for diesel engines, is that they
have a groove for an oil ring below the
gudgeon pin, in addition to the rings
between the gudgeon pin and crown.

The name 'trunk piston' derives from the

'trunk engine', an early design of marine
steam engine. To make these more
compact, they avoided the steam engine's
usual piston rod with separate crosshead
and were instead the first engine design to
place the gudgeon pin directly within the
piston. Otherwise these trunk engine
pistons bore little resemblance to the trunk
piston; they were extremely large diameter
and double-acting. Their 'trunk' was a
narrow cylinder mounted in the centre of
the piston.

Media related to Trunk pistons at

Wikimedia Commons

Crosshead pistons …
Large slow-speed Diesel engines may
require additional support for the side
forces on the piston. These engines
typically use crosshead pistons. The main
piston has a large piston rod extending
downwards from the piston to what is
effectively a second smaller-diameter
piston. The main piston is responsible for
gas sealing and carries the piston rings.
The smaller piston is purely a mechanical
guide. It runs within a small cylinder as a
trunk guide and also carries the gudgeon
pin.

Lubrication of the crosshead has

advantages over the trunk piston as its
lubricating oil is not subject to the heat of
combustion: the oil is not contaminated by
combustion soot particles, it does not
break down owing to the heat and a
thinner, less viscous oil may be used. The
friction of both piston and crosshead may
be only half of that for a trunk piston.[3]

Because of the additional weight of these

pistons, they are not used for high-speed
engines.

Media related to Crosshead pistons at

Wikimedia Commons

Slipper pistons …
Slipper piston

A slipper piston is a piston for a petrol

engine that has been reduced in size and
weight as much as possible. In the
extreme case, they are reduced to the
piston crown, support for the piston rings,
and just enough of the piston skirt
remaining to leave two lands so as to stop
the piston rocking in the bore. The sides of
the piston skirt around the gudgeon pin
are reduced away from the cylinder wall.
The purpose is mostly to reduce the
reciprocating mass, thus making it easier
to balance the engine and so permit high
speeds.[4] In racing applications, slipper
piston skirts can be configured to yield
extremely light weight while maintaining
the rigidity and strength of a full skirt.[5]
Reduced inertia also improves mechanical
efficiency of the engine: the forces
required to accelerate and decelerate the
reciprocating parts cause more piston
friction with the cylinder wall than the fluid
pressure on the piston head.[6] A
secondary benefit may be some reduction
in friction with the cylinder wall, since the
area of the skirt, which slides up and down
in the cylinder is reduced by half. However,
most friction is due to the piston rings,
which are the parts which actually fit the
tightest in the bore and the bearing
surfaces of the wrist pin, and thus the
benefit is reduced.

Media related to Slipper pistons at

Wikimedia Commons

Deflector pistons …

Two-stroke deflector piston

Deflector pistons are used in two-stroke
engines with crankcase compression,
where the gas flow within the cylinder
must be carefully directed in order to
provide efficient scavenging. With cross
scavenging, the transfer (inlet to the
cylinder) and exhaust ports are on directly
facing sides of the cylinder wall. To
prevent the incoming mixture passing
straight across from one port to the other,
the piston has a raised rib on its crown.
This is intended to deflect the incoming
mixture upwards, around the combustion
chamber.[7]
Much effort, and many different designs of
piston crown, went into developing
improved scavenging. The crowns
developed from a simple rib to a large
asymmetric bulge, usually with a steep
face on the inlet side and a gentle curve on
the exhaust. Despite this, cross
scavenging was never as effective as
hoped. Most engines today use Schnuerle
porting instead. This places a pair of
transfer ports in the sides of the cylinder
and encourages gas flow to rotate around
a vertical axis, rather than a horizontal
axis.[8]
 Media related to Deflector pistons at
Wikimedia Commons

Racing Pistons …

Early (c. 1830) piston for a beam engine. The piston

seal is made by turns of wrapped rope.

In racing engines, piston strength and

stiffness is typically much higher than that
of a passenger car engine, while the
weight is much less, to achieve the high
engine RPM necessary in racing.[9]

Hydraulic cylinders …

Pistons of Hydraulic cylinders used in a hot press

Hydraulic cylinders can be both single-

acting or double-acting. A hydraulic
actuator controls the movement of the
piston back and/or forth. Guide rings
guides the piston and rod and absorb the
radial forces that act perpendicularly to
the cylinder and prevent contact between
sliding the metal parts.

Steam engines …

Cast-iron steam engine piston, with a metal piston

ring spring-loaded against the cylinder wall
ring spring loaded against the cylinder wall.

Steam engines are usually double-acting

(i.e. steam pressure acts alternately on
each side of the piston) and the admission
and release of steam is controlled by slide
valves, piston valves or poppet valves.
Consequently, steam engine pistons are
nearly always comparatively thin discs:
their diameter is several times their
thickness. (One exception is the trunk
engine piston, shaped more like those in a
modern internal-combustion engine.)
Another factor is that since almost all
steam engines use crossheads to
translate the force to the drive rod, there
are few lateral forces acting to try and
"rock" the piston, so a cylinder-shaped
piston skirt isn't necessary.

Pumps
Piston pumps can be used to move liquids
or compress gases.

For liquids …

For gases …

Air cannons
There are two special type of pistons used
in air cannons: close tolerance pistons and
double pistons. In close tolerance pistons
O-rings serve as a valve, but O-rings are
not used in double piston types.

See also
Air gun
Fire piston
Fruit press
Gas-operated reloading, using a gas
piston
Hydraulic cylinder
Shock absorber
Slide whistle
Steam locomotive components
 Syringe
Wankel engine, an internal combustion
engine design with a rotor replacing the
piston

Notes
i. 'Gas' here refers to a fuel gas, not
gasoline.
ii. A handful of submarines in the
following class used a similar engine,
with almost equally poor results.

References
1. Magda, Mike. "What Makes A Racing
Piston?" . Retrieved 2018-04-22.
2. Bailey, Kevin. "Full-Round vs. Strutted:
Piston Forging Designs and Skirt
Styles Explained" . Retrieved
2018-07-15.
3. Ricardo (1922), p. 116.
4. Ricardo (1922), p. 149.
5. Piston with improved side loading
resistance , 2009-10-12, retrieved
2018-04-22
. Ricardo (1922), pp. 119–120, 122.
7. Irving, Two stroke power units, pp. 13–
15.
. Irving, Two stroke power units, pp. 15–
16.
 9. "Racing Piston Technology – Piston
Weight And Design – Circle Track
Magazine" . Hot Rod Network. 2007-
05-31. Retrieved 2018-04-22.

Bibliography
Irving, P.E. (1967). Two-Stroke Power
Units. Newnes.
Ricardo, Harry (1922). The Internal
Combustion Engine. Vol I: Slow-Speed
Engines (1st ed.). London: Blackie.

External links

Wikimedia Commons has media

related to Pistons.
 Piston Engines Essay
How Stuff Works – Basic Engine Parts

Retrieved from
"https://en.wikipedia.org/w/index.php?
title=Piston&oldid=970914917"

Last edited 2 months ago by Filedelinkerbot

Content is available under CC BY-SA 3.0 unless

otherwise noted.