ECO INSTRUMENT (NS0081046-M) DoHP200
Portable Hardness Tester
Dono is a small, light and portable tester. It is most
suitable for testing of heavy, big or outdoor metal
parts. It can measure in any direction and also easy
to be used and accurate on curved test surfaces.
Especially, it can automatically compensate effect
of weight which according to the test direction.
DoHP200 uses wireless IR to communicate with
printer, operates with touch screen and test data
could be linked into PC.
Conforms to the Standard ASTM A956 and DIN
50156.
Measuring Principle Scope:
DoHP200 Portable Hardness Tester measuring principle is physically a rather simple,
dynamic hardness test. An impact body with a hard metal test tip is propelled by spring
force against the surface of the test piece. Surface deformation takes place when the
impact body hits the test surface, which will result in loss of kinetic energy. This energy
loss is calculated by velocity measurements when the impact body is at a precise distance
from the surface for both the impact and rebound phase of the test. The permanent magnet
in the impact body generates an induction voltage in the single coil of the impact device.
The voltage of the signal is proportional to the velocity of the
impact body, and signal processing by the electronics provides the
hardness reading for display and storage.
Simply put, harder materials produce higher rebound velocity than those which are less hard (higher L
value). DoHP200 Portable Hardness Tester is a direct hardness measurement within any particular
material group (i.e. steel, aluminum, etc.) and can be used as a final test result without conversion.
However, DoHP200 Portable Hardness Tester has established conversions to other hardness scales for
the convenience of our customers. These conversions to other scales (HRC, HRB, HB, HV, HSD etc.) are
programmed into the electronics, and can be shown directly on the display as the test result. All data is
stored in the native L scale to prevent any possible errors with multiple conversions.
The Hardness Value “L”
This term, 1978 introduced by Doctor Dietmar Leeb into measuring technology, is the quotient for the
impact body's rebound and impact velocity, multiplied by 1000. Harder materials produce higher rebound
velocity than those which are less hard. With reference to a particular material group (e.g. steel,
aluminum etc.) the L-value represents a direct hardness measurement and is used as such. Comparison
curves with standard static hardness values have been established (Brinell, Vickers, Rockwell C, B) for the
most prevalent materials, enabling the L values to be converted into the relevant values for these
procedures. With DoPH200 Portable Hardness Tester, such hardness values can be directly displayed in
the hardness scales HRC, HRB, HB, HV, HSD and tensile strength (MPa).
Address: 663, Jalan Haruan 4/10,Oakland Commercial Centre, 70300 Seremban. Negeri Sembilan Darul Khusus.
Tel: +606-631 1758 Fax: +606-631 0952
Email: [email protected]
Website: http://www.ecoinstrument.com.my
ECO INSTRUMENT (NS0081046-M) DoHP200
Features:
Highly accurate ±6HL
Automatic correction for impact direction
Large, easy to read display with backlight
Menu language: English, Deutech, French, Italian, Spanish, Russian, Polish, Farsi, Korean, Chinese
Simplified, Chinese Traditional
To operate with touch screen
Large memory with on-screen review of data
Converts to all common hardness scales (HV, HB, HRC, HRB, HSD) and tensile strength MPa.
Rechargeable Ni-MH batteries
Automatically detect the Impact Device type
Conforms to the Standard DIN 50156 and ASTM A956-02
Application Range:
Good for all metals
Ideal for production level testing
Best suited for an-site testing of heavy, big or already installed parts
Handy for difficult to access or confined test locations
Automatic compensation for impact direction
Excellent for material selection and acceptance tests
Easy to use and accurate on curved test surfaces (R >10mm)
Metal production & processing
Automotive & transportation Machinery & power plants
Petro-chemical, refineries
Aerospace & shipyard
Metal Constructions
Testing services & laboratories
Technical Information:
Model DoHP200
HL display range 170~960HLD
Repeatability 6HLD
Conversion unit Vickers conversion unit HV (automatic), other conversion unit HB,
HRC, HRB, HSD and tensile strength MPa
Testing direction All direction
Address: 663, Jalan Haruan 4/10,Oakland Commercial Centre, 70300 Seremban. Negeri Sembilan Darul Khusus.
Tel: +606-631 1758 Fax: +606-631 0952
Email: [email protected]
Website: http://www.ecoinstrument.com.my
ECO INSTRUMENT (NS0081046-M) DoHP200
Optional Impact Device D, DC, DL, D+15, C, G (automatic identification)
Display 3.9inch 240 x 320 touch screen, LCD display with back light
Operating voltage 3.6V Rechargeable Ni-MH batteries
English, Korean, Deutsch, French, Italian, Spanish, Russian, Polish,
Multi-language menu
Chinese Simplified, Chinese Traditional.
Charger DC5V/1A
Printer Wireless Mini-Printer (Cable no needed)
Communication USB to PC for transfer data
Operating environment Temperature: -20 ~ +50°C
Humidity: 20% ~ 85%
Storage environment Temperature: -30 ~ +70°C
Humidity: 5% ~ 95%
Dimension 130mm x 86mm x 28mm
Weight 300g (include D Type Impact Device)
Certificate CE
Display Unit, Impact Device D, Test Block, Mini-printer, Charger,
Accessories
Little Support Ring, Cleaning Brush, USB Cable, PC Software
Optimal Accessories Impact Device DC, DL, D+15, C, G, Support Ring Set
Impact Unit D (Measuring General Piece)
Impact energy 11 Nm
Test of the impact body 5.5g
Test tip diameter 3mm
Test tip material Tungsten carbide
Test tip hardness ≥1600HV
Impact length 147mm
Impact maximum diameter 20mm
Impact weight 75g
Address: 663, Jalan Haruan 4/10,Oakland Commercial Centre, 70300 Seremban. Negeri Sembilan Darul Khusus.
Tel: +606-631 1758 Fax: +606-631 0952
Email: [email protected]
Website: http://www.ecoinstrument.com.my
ECO INSTRUMENT (NS0081046-M) DoHP200
Impact Devices
Preparation of the surface D,DC, D1, D+15 C G
Roughness class ISO N7 N5 N9
Max. roughness depth Rt 10µm 2.5µm 30µm
Centre line average CLA, AA, Ra 2 µm 0.4 µm 7 µm
Min. weight of samples
of compact shape 5 kg 1.5 kg 15 kg
on solid support 2 kg 0.5 kg 5 kg
coupled on plate 0.1 kg 0.02 kg 0.5 kg
Min. thickness of sample
uncoupled 25 mm 15 mm 70 mm
coupled 3 mm 1 mm 10 mm
surface layer thickness 0.8 mm 0.2 mm
Max. Hardness of samples:
Indentation size on test surface with 300HV, 30HRC*
diameter 0.54 mm 0.38 mm 1.03 mm
depth 24 µm 12 µm 53 µm
Indentation size on test surface with 600 HV, 55 HRC *
diameter 0.45 mm 0.32 mm 0.90 mm
depth 17µm 8 µm 41 µm
Indentation size on test surface with 800 HV, 63 HRC *
diameter 0.35mm 0.30 mm
depth 10µm 7 µm
* Approximate hardness conversion for steel
Address: 663, Jalan Haruan 4/10,Oakland Commercial Centre, 70300 Seremban. Negeri Sembilan Darul Khusus.
Tel: +606-631 1758 Fax: +606-631 0952
Email: [email protected]
Website: http://www.ecoinstrument.com.my
ECO INSTRUMENT (NS0081046-M) DoHP200
Measure Mode:
1. Impact unit type: The impact unit type that connected to the display unit.
2. Material group: The material of the sample.
3. Battery remaining indicator: indicate the remaining time of battery.
4. Conversion value: The conversion value of measured value “L”.
Note:
When “---” appear at this position, indicated the conversion is out of range.
5. Impact direction: Display the impact direction.
6. Hardness value L: Measured hardness value L (Leeb).
7. Statistic values:
- X: Mean value.
S: The difference of maximum value and the minimum value.
8. Statistic times: The impact times in a statistic data group
9. Impact times counter: Finished times of impact
10. Time and date: time and date of the system
11. Backlight on/off: click it will turn on the backlight when backlight is off; when backlight is on, click it
will turn off the backlight.
Address: 663, Jalan Haruan 4/10,Oakland Commercial Centre, 70300 Seremban. Negeri Sembilan Darul Khusus.
Tel: +606-631 1758 Fax: +606-631 0952
Email: [email protected]
Website: http://www.ecoinstrument.com.my
ECO INSTRUMENT (NS0081046-M) DoHP200
SCALE RANGE – D & DC Type:
Material HV HB HRC HRB HSS Tensile Strength
MPa
Steel & Cast Steel 81-955 81-654 20.0-68.4 38.4-99.5 32.5-99.5 375-2639
Alloy Tool Steel 80-898 20.4-67.1 375-2639
Stainless Steel 85-802 85-655 19.6-62.4 46.5-101.7 740-1725
Grey Cast Iron 63-336
Ductile Iron 140-387
Cast Aluminum Allo ys 19-164 23.8-84.6
Brass 40-173 13.5-95.3
Bronze 60-290
Copper 45-315
Forging Steel 83-976 142-651 19.8-68.5 59.6-99.6 26.4-99.5
SCALE RANGE - DL Type:
Material HLDL HRC HRB HB HV HSD
Steel & Cast Steel 560-950 20-68.4 38.4-99.5 81-654 81-955 32.5-97.9
SCALE RANGE - C Type:
Material HLC HRC HB HV HSD
Steel 350-960 20.0-69.5 80.683 80-996 31.9-102
SCALE RANGE – D+15 Type:
Material HLD+15 HRC HB HV HSD
Steel 481-850 20-64 188-654 192-825 32.5-88.4
SCALE RANGE – G Type:
Material HLG HRB HB
Steel 300-750 47.7-99.9 90.646
Grey Cast Iron 340-600 92-326
Ductile Iron 340-600 127-364
Address: 663, Jalan Haruan 4/10,Oakland Commercial Centre, 70300 Seremban. Negeri Sembilan Darul Khusus.
Tel: +606-631 1758 Fax: +606-631 0952
Email: [email protected]
Website: http://www.ecoinstrument.com.my
