NTSC Video Recorder SR-V10U

VIDEO CASSETTE RECORDER
SR-V10U
CABLE/ MBR SET

TV DBS A/B
POWER
TV/VCR A. MONITOR DISPLAY
1 2 3
2
4 5 6
DBS DAILY WEEKLY
7 8 9
C.RESET AUX
CANCEL 0 TIMER 4
START STOP DATE CH
EXPRESS PROGRAMMING
1 PROG PROG SP/EP SKIP SEARCH

CHECK
PLAY REW FF
REW FF
PLAY
STOP PAUSE
REC
POWER – +
3 OK
MENU TV CH +
CH– /+
PUSH / TURN
SHUTTLE
PLUS
TV
+
L
VO
L V
–
TV REC LINK A.DUB
T V CH – S VIDEO VIDEO (MONO)L—AUDIO—R 24HR QUICK
PROGRAM
SP EP
DIGITAL TBC/NR VCR INSERT REC PAUSE STOP/EJECT
MULTI BRAND
REMOTE CONTROL UNIT
For Customer Use:
INSTRUCTIONS Enter below the Model No. and

Serial No. which are located on the
rear of cabinet. Retain this
information for future reference.
Model No.
Serial No.
LPT0604-001A
Downloaded from www.Manualslib.com manuals search engine

2 EN
Dear Customer,
Thank you for purchasing the JVC S-VHS video cassette recorder. Before use, please read the safety information and precautions
contained in the following pages to ensure safe use of your new VCR.
CAUTIONS Caution on Replaceable lithium battery

The battery used in this device may present a fire or
chemical burn hazard if mistreated. Do not recharge,
disassemble, heat above 100°C or incinerate.
CAUTION Replace battery with Panasonic (Matsushita Electric),
RISK OF ELECTRIC SHOCK
DO NOT OPEN Sanyo, Sony or Maxell CR2025. Danger of explosion or
Risk of fire if the battery is incorrectly replaced.
n Dispose of used battery promptly.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
n Keep away from children.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
n Do not disassemble and do not dispose of in fire.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral Declaration of Conformity
triangle, is intended to alert the user to the presence of
uninsulated "dangerous voltage" within the product's enclosure Model Number :SR-V10U
that may be of sufficient magnitude to constitute a risk of electric Trade Name :JVC
shock to persons.
Responsible Party :JVC Americas Corp.
The exclamation point within an equilateral triangle is intended to Address :1700 Valley Road Wayne,
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature N.J. 07470
accompanying the appliance. Telephone Number :973-315-5000
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
WARNING: (1) This device may not cause harmful interference, and (2)
TO PREVENT FIRE OR SHOCK this device must accept any interference received,
including interference that may cause undesired operation.
HAZARD, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
CAUTION: Failure to heed the following precautions may result in
This video cassette recorder should be used with AC damage to the VCR, Remote or video cassette.
120V`, 60Hz only. 1. DO NOT place the VCR . . .
To prevent electric shocks and fire hazards, DO NOT use ... in an environment prone to extreme temperatures or
any other power source. humidity.
... in direct sunlight.
CAUTION: ... in a dusty environment.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE ... in an environment where strong magnetic fields are
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. generated.
... on a surface that is unstable or subject to vibration.
ATTENTION: 2. DO NOT block the VCR’s ventilation openings.
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE 3. DO NOT place heavy objects on the VCR or on the Remote.
LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE 4. DO NOT place anything which might spill on the top of the
CORRESPONDANTE DE LA PRISE ET POUSSER VCR or on the Remote.
JUSQU'AU FOND. 5. AVOID violent shocks to the VCR during transport.
VCR Plus+ and PlusCode are registered trademarks of Gemstar

Note to CATV system installer: Development Corporation.
This reminder is provided to call the CATV system The VCR Plus+ system is manufactured under license from
installer’s attention to Article 820-40 of the NEC that Gemstar Development Corporation.
provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
cable entry as practical.
CAUTION: n Cassettes marked "S-VHS" and "VHS" can be used with this
Changes or modifications not approved by JVC could void
video cassette recorder. However, S-VHS recordings are
user’s authority to operate the equipment.
possible only with cassettes marked "S-VHS".
By using S-VHS ET it is possible to record and play back with
S-VHS picture quality on VHS cassettes with this VCR.
n As an ENERGY STAR® Partner, JVC has determined that this
product or product model meets the ENERGY STAR® guidelines
for energy efficiency.

EN 3
IMPORTANT PRODUCT 5. Ventilation
Slots and openings in the cabinet are provided for ventilation.
To ensure reliable operation of the product and to protect it
SAFETY INSTRUCTIONS from overheating, these openings must not be blocked or
covered.
• Do not block the openings by placing the product on a bed,
Electrical energy can perform many useful functions. But sofa, rug or other similar surface.
improper use can result in potential electrical shock or fire • Do not place the product in a built-in installation such as a
hazards. This product has been engineered and manufactured bookcase or rack unless proper ventilation is provided or the
to assure your personal safety. In order not to defeat the built-in manufacturer’s instructions have been adhered to.
safeguards, observe the following basic rules for its installation,
use and servicing. 6. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as
ATTENTION: recommended by the manufacturer.
Follow and obey all warnings and instructions marked on your
product and its operating instructions. For your safety, please
read all the safety and operating instructions before you operate
this product and keep this booklet for future reference.
ANTENNA INSTALLATION
INSTRUCTIONS
1. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the
INSTALLATION product, be sure the antenna or cable system is grounded so as
1. Grounding or Polarization to provide some protection against voltage surges and built-up
(A) Your product may be equipped with a polarized alternating- static charges. Article 810 of the National Electrical Code,
current line plug (a plug having one blade wider than the ANSI/NFPA 70, provides information with regard to proper
other). This plug will fit into the power outlet only one way. grounding of the mast and supporting structure, grounding of
This is a safety feature. the lead-in wire to an antenna discharge unit, size of grounding
If you are unable to insert the plug fully into the outlet, try connectors, location of antenna discharge unit, connection to
reversing the plug. If the plug should still fail to fit, contact grounding electrodes, and requirements for the grounding
your electrician to replace your obsolete outlet. Do not electrode.
defeat the safety purpose of the polarized plug.
(B) Your product may be equipped with a 3-wire grounding-type 2. Lightning
plug, a plug having a third (grounding) pin. This plug will For added protection for this product during a lightning storm,
only fit into a grounding-type power outlet. This is a safety or when it is left unattended and unused for long periods of
feature. time, unplug it from the wall outlet and disconnect the antenna
If you are unable to insert the plug into the outlet, contact or cable system. This will prevent damage to the product due to
your electrician to replace your obsolete outlet. Do not lightning and power-line surges.
defeat the safety purpose of the grounding-type plug.
3. Power Lines
2. Power Sources An outside antenna system should not be located in the vicinity
Operate your product only from the type of power source of overhead power lines or other electric light or power circuits,
indicated on the marking label. If you are not sure of the type of or where it can fall into such power lines or circuits. When
power supply to your home, consult your product dealer or installing an outside antenna system, extreme care should be
local power company. If your product is intended to operate taken to keep from touching such power lines or circuits as
from battery power, or other sources, refer to the operating contact with them might be fatal.
instructions.
3. Overloading
Do not overload wall outlets, extension cords, or integral EXAMPLE OF ANTENNA GROUNDING AS PER
convenience receptacles as this can result in a risk of fire or NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
electric shock.
4. Power Cord Protection ANTENNA

LEAD IN WIRE
Power supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against GROUND CLAMP
them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product. ANTENNA
DISCHARGE UNIT
(NEC SECTION
810-20)
ELECTRIC SERVICE
EQUIPMENT
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE

4 EN
USE SERVICING
1. Accessories 1. Servicing
To avoid personal injury: If your product is not operating correctly or exhibits a marked
• Do not place this product on an unstable cart, stand, tripod, change in performance and you are unable to restore normal
bracket, or table. It may fall, causing serious injury to a child operation by following the detailed procedure in its operating
or adult, and serious damage to the product. instructions, do not attempt to service it yourself as opening or
• Use only with a cart, stand, tripod, bracket, or table removing covers may expose you to dangerous voltage or other
recommended by the manufacturer or sold with the product. hazards. Refer all servicing to qualified service personnel.
• Use a mounting accessory recommended by the
manufacturer and follow the manufacturer’s instructions for 2. Damage Requiring Service
any mounting of the product. Unplug this product from the wall outlet and refer servicing to
• Do not try to roll a cart with small casters across thresholds or qualified service personnel under the following conditions:
deep-pile carpets. a. When the power supply cord or plug is damaged.
b.If liquid has been spilled, or objects have fallen into the
2. Product and Cart Combination product.
A product and cart combination should PORTABLE CART WARNING
c. If the product has been exposed to rain or water.
be moved with care. Quick stops, (Symbol provided by RETAC) d.If the product does not operate normally by following the
excessive force, and uneven surfaces operating instructions. Adjust only those controls that are
may cause the product and cart covered by the operating instructions as an improper
combination to overturn. adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to its normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in
performance—this indicates a need for service.
3. Water and Moisture 3. Replacement Parts

Do not use this product near water—for example, near a bath When replacement parts are required, be sure the service
tub, wash bowl, kitchen sink or laundry tub, in a wet basement, technician has used replacement parts specified by the
or near a swimming pool and the like. manufacturer or which have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock or other hazards.
4. Object and Liquid Entry
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or short- 4. Safety Check
out parts that could result in a fire or electric shock. Never spill Upon completion of any service or repairs to this product, ask
liquid of any kind on the product. the service technician to perform safety checks to determine
that the product is in safe operating condition.
5. Attachments
Do not use attachments not recommended by the manufacturer
of this product as they may cause hazards.
HOW TO USE THIS INSTRUCTION
MANUAL
6. Cleaning ● The Index on pages 58 – 62 lists frequently-used terms, and
Unplug this product from the wall outlet before cleaning. Do the number of the page on which they are used or explained
not use liquid cleaners or aerosol cleaners. Use a damp cloth in the manual. This section also illustrates the controls and
for cleaning. connections on the front and rear panel, the front display
panel and the Remote.
7. Heat ● The Z mark signals a reference to another page for
The product should be situated away from heat sources such as instructions or related information.
radiators, heat registers, stoves, or other products (including ● Operation buttons necessary for the various procedures are
amplifiers) that produce heat. clearly indicated through the use of illustrations at the
beginning of each major section.
BEFORE YOU INSTALL YOUR NEW

VCR . . .
. . . please read the sections/literature listed below.
● ”CAUTIONS” on page 2
● ”IMPORTANT PRODUCT SAFETY INSTRUCTIONS” on the
previous page

CONTENTS EN 5
INSTALLING YOUR NEW VCR 6 SPECIAL EFFECT PLAYBACK 26
Basic Connections .................................. 6 Special Effect Playback ........................ 26
Locating particular scene rapidly
INITIAL SETTINGS 8 — Picture Search ..................................................... 26
Viewing still picture — Still Picture Playback ........... 27
Plug & Play Setting ................................ 8 Skipping unwanted portions — Skip Search ............. 27
Auto Clock Set/Auto Tuner Set ................................... 8 Viewing still picture frame by frame
Clock Setting ........................................ 10 — Frame-by-Frame Playback ................................... 27
Preparations ............................................................. 10 Viewing slow motion picture
Setting clock semiautomatically — Slow Motion Playback ........................................ 27
— Semiauto Clock Set ............................................. 11
Setting clock manually TIMER RECORDING 28
— Manual Clock Set ................................................ 12
VCR Plus+® Timer Programing .............. 28
Tuner Setting ....................................... 13
Setting channels automatically
Changing VCR Plus+® Setting ................ 30
— Auto Channel Set ................................................ 13 Express Timer Programing ................... 32
Setting channels manually 24HR Quick Programing ...................... 34
— Manual Channel Set ............................................ 14 Checking program settings ....................................... 35
Canceling or changing program settings .................. 35
BASIC PLAYBACK AND RECORDING 15 When programs overlap each other ......................... 36
Basic Playback .................................... 15
To stop playback ...................................................... 15 OTHER USEFUL FUNCTIONS 37
To rewind the tape ................................................... 15 Useful Function Settings ....................... 37
To fast-forward the tape ........................................... 15
To eject the tape ...................................................... 15 Satellite Auto Recording ....................... 42
To turn off the VCR .................................................. 15 Child Lock ............................................ 43
Basic Playback Features ...................... 16
Changing display information .................................. 16 EDITING 44
Checking tape position ............................................ 16
Playing back tape repeatedly — Repeat Play ........... 16
Edit From Camcorder ........................... 44
Adjusting tracking condition Edit To Or From Another VCR ............... 46
— Tracking Adjustments .......................................... 17 Audio Dubbing .................................... 47
Selecting monitor sound — Audio Monitor .............. 17
Automatic operations after rewinding Insert Editing and AV Dubbing ............. 48
— Next Function Memory ....................................... 17
Locating beginning of recordings MULTI-BRAND REMOTE CONTROL 50
— Index Search ....................................................... 17
Locating beginning of timer recordings
TV Brand Setting .................................. 50
— Instant Review ..................................................... 18 Cable Box Brand Setting ...................... 51
Adjusting picture condition DBS Receiver Brand Setting .................. 52
— Digital TBC/NR ................................................... 18
Changing Remote Control Code ............ 53
Basic Recording ................................... 19
To pause recording .................................................. 19 TROUBLESHOOTING 54
To stop recording ..................................................... 19
To rewind the tape (when it is not running) .............. 19 Questions and answers ............................................ 57
To fast-forward the tape (when it is not running) ...... 19
To eject the tape ...................................................... 19 INDEX 58
To turn off the VCR .................................................. 19 List of terms .............................................................58
Basic Recording Features ..................... 20 Front panel ..............................................................59
Changing display information .................................. 20 Front display panel .................................................. 60
Recording on one tape repeatedly Rear panel ...............................................................61
— Repeat Recording ............................................... 20 On-screen display .................................................... 61
Watching one program while recording another ...... 20 Remote ....................................................................62
Showing on-screen display ...................................... 21
SPECIFICATIONS 63
SERIES PLAYBACK AND RECORDING 22
Series Playback ................................... 22
Series Recording .................................. 24

6 EN INSTALLING YOUR NEW VCR
Basic Connections
ANTENNA IN
(Antenna or cable input)
Antenna or cable
Coaxial cable
Flat feeder
Matching transformer
VIDEO OUT AUDIO OUT (Not supplied)
AC Power
Cord
REMOTE
IN IN OUT ANTENNA IN
REMOTE
R
OUT
AUDIO
S
IN OUT L VHF/UHF
V TV OUT
I VIDEO
D
E
O
Back of VCR
S VIDEO OUT
TV OUT
AC Outlet
S-video cable
(Supplied)
To S-video input
connector
Audio/video cable
(Supplied)
To Audio/video input
connectors
RF cable (Supplied)
To 75 ohm terminal
TV

EN 7
1 Check contents
Make sure the package contains all of the 4 Connect VCR to power source
Connect the AC power plug to an AC outlet.
accessories listed in “SPECIFICATIONS”
(Z␣ pg.␣ 63). ● The clock and tuner channels will
automatically be set when the antenna is
connected and when the AC power cord is first
2 Situate VCR
Place the VCR on a stable, horizontal surface.
connected to an AC power outlet (Z pg. 8).
(If “Auto” or “CH” is displayed on the front display
panel before the VCR is turned on, the clock and
3 Connect VCR to TV
The following connections are required.
tuner channels are being set automatically. Wait
until the clock time is displayed on the front display
RF Connection panel before turning on the VCR.)
1 Disconnect the TV antenna from the TV.
2 Connect the TV antenna cable to the
ANTENNA IN terminal on the rear of the VCR.
5 Set VCR channel
Press POWER to turn off the VCR and press STOP/
3 Connect the supplied RF cable between the TV EJECT ( § ) on the front panel for more than
OUT terminal on the rear of the VCR and the 5␣ seconds. “3CH” appears on the display panel.
TV’s antenna input terminal. Press CH + and – on the Remote to select “3CH” or
“4CH” for only RF connection, “–CH” (OFF) for RF
AV Connection (improves picture quality during and AV connection, then press OK.
tape playback.) ● The VCR channel is preset to 3CH.
If your TV is equipped with audio/video input Set to 4CH if 3CH is used for broadcasting in your
connectors area. (To view the picture from this VCR through
1 Connect the antenna, VCR and TV as shown in this channel, select the same channel on the TV
the illustration. with the VCR channel setting on the VCR.)
2 Connect an audio/video cable between the ● You can now perform basic playback
AUDIO/VIDEO OUT connectors on the rear of (Z␣ pg.␣ 15) or basic recording (Z␣ pg.␣ 19).
the VCR and the audio/video input connectors
on the TV. NOTES:
S-video Connection (allows you to make the ● The VCR channel is the channel on which you can watch the
most of the S-VHS picture performance.) picture from the VCR on the TV when only using the RF
connection.
If your TV is equipped with an S-video input ● Even if you are using audio/video cables to connect your VCR
connector to your TV, you must also connect it using the RF cable. This
1 Perform “RF Connection” and RED/WHITE will ensure that you can record one show while watching
AUDIO connections. another (Z pg. 21).
2 Connect an S-video cable between the S VIDEO ● For full identification of the VCR’s rear panel, refer to the
OUT connector on the rear of the VCR and the Index ( Z pg. 61).
S-video input connector on the TV.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Be sure to connect the power plug to an AC outlet first Installing/Removing the lithium battery
before installing the lithium battery; otherwise, the 1 Make sure that the power plug is connected to an AC outlet
battery's service life will be drastically shortened. and turn off the VCR power.
2 Open the battery cover while pressing the release tab as
illustrated.
3 Insert a lithium battery with the plus (+) side up and push it in.
● To remove the lithium battery, press the latch A down-
REMOTE
ward using a pointed non-metallic object, then pull out
R
S
IN
REMOTE
OUT
OUT
AUDIO
L VHF/UHF
the lithium battery.
V
I
D
E
O
VIDEO
TV OUT
4 Close the battery cover until it clicks in place.

8 EN INITIAL SETTINGS
Plug & Play This VCR sets the clock and tuner channels
automatically when AC power cord is first connected to
an AC outlet. The antenna cable must be connected for
Setting
the Plug & Play setting.
The time and date can be set automatically by the clock
setting data transmitted from one of the regular TV
broadcast channels. We call this TV channel the “host
channel” and it is a PBS channel in your area.
Auto Clock Set/Auto Tuner Set
ATTENTION
1 Perform Plug & Play setup
Connect the antenna cable to the VCR (Z pg.
● If you use a cable box, Plug & Play will not function; set 6). Then connect the AC power cord to an AC
the clock and tuner channels separately. (Z pg.10 – 14) outlet. Do not turn on the VCR.
● It takes several minutes for the VCR to complete the Plug The clock and tuner channels will be set
& Play setting. automatically.
● Do not press any buttons on the front panel or on the
Remote while Plug & Play is in progress. NOTES:
● Auto Clock Set is performed first.
“Auto” blinks on the front display panel during Auto
Clock Set.
● Auto Channel Set is performed next. Auto Channel
Set scans all the channels that are receivable by your
REW FF
VCR. During Auto Channel Set, the channel numbers
POWER
PLAY
– +
are displayed as they are scanned and set.
CH– /+
PUSH / TURN
● When Plug & Play setting has been complete
S VIDEO VIDEO (MONO)L—AUDIO—R
REC LINK A.DUB
24HR QUICK
successfully, the correct clock time is displayed. If you
PROGRAM
DIGITAL TBC/NR
SP EP
VCR INSERT REC PAUSE STOP/EJECT
perform Plug & Play setting successfully, there is no
need to perform the clock (Z pg. 10) and tuner (Z pg.
13) settings. If, however, you want to add or delete
channels, refer to Manual Channel Set on page 14.
During Initial Auto Clock Set During Auto Channel Set Plug & Play Completed
“Auto” blinks. The channel numbers are displayed The current time (including
as they are scanned and set. AM/PM) is displayed.
* If an incorrect clock time or “– –:– –” appears on the display panel, see “What to do if Plug & Play setting failed”
below.

EN 9
INFORMATION
● If “AUTO CLOCK” is set to “ON” on the Clock Set screen on page 11, the clock will be adjusted automatically by the host
channel every hour (except 11:00 PM, midnight, 1:00 AM and 2:00 AM) using the incoming PBS channel clock setting data.
(This automatic clock adjustment can only be performed when the VCR is turned off. The clock will be adjusted just on these
hours — on the time displayed on the front display panel, not on the actual real time.)
The default setting of “AUTO CLOCK” is “ON”.
● If the memory backup fails, because a power outage occurs or because the AC power cord is unplugged, Plug & Play will be
performed when power is restored to the VCR.
● Poor antenna or cable signal may prevent the VCR from receiving the Auto clock setting data from the PBS channel. If this
function is taking a considerable amount of time, it may be necessary to perform the Semiauto or Manual Clock Set
procedure.
What to do if Plug & Play setting failed

● If an incorrect time is displayed on the front display panel, you may be receiving the clock setting data of a PBS channel from
an adjacent time zone, or an incorrect PBS channel from a cable TV system. In this case, perform the Semiauto (Z pg. 11) or
Manual Clock Set (Z pg. 12) procedure.
● If “- -:- -” appears on the front display panel, your antenna cable may not be connected to the VCR or there may not be a Host
PBS signal available in your area. Ensure that the antenna cable is connected correctly. Then turn on and off the VCR; the Plug
& Play setting will be automatically reactivated.
If Plug & Play setting is not performed though the antenna cable is connected correctly, perform Manual Clock Set (Z pg. 12)
and Auto Channel Set or Manual Channel Set (Z pg. 13 or 14).
Last-Function Memory
When the AC is removed from the VCR or when the power failure occurs, your settings for the following functions
are kept in memory. These settings will resume when the VCR is turned on again.
a- Input Selection (channel or auxiliary input; L-1 or F-1)
b- Recording tape speed (Z pg. 19)
c- “ON SCREEN (REC)” (Z pg. 37, 38)
d- “ON SCREEN (PLAY)” (Z pg. 37, 39)
e- “RETURN POINT” (Z pg. 37, 41)
f- “DAY/TIME INSERT” (Z pg. 37, 41)
g- “REC SAFETY” (Z pg. 37, 41)

10 EN INITIAL SETTINGS (cont.)
Clock Setting Perform clock setting only if the clock has not been set
correctly by the Plug & Play setting or if you use a cable
box.
Access the Clock Set screen to perform the Semiauto or
Manual Clock Set. Each procedure starts from step 4
Turn on the VCR and the TV, and select the VCR
after preparation steps below are finished.
channel 3 or 4 (or AV mode) on the TV.
If you use a cable box, set the clock manually. (Z pg. 12)
Preparations
1 Access Main Menu screen

Press MENU.
1 2 3
2
2 Access Initial Set screen
Press SHUTTLE PLUS MAIN MENU
4 5 6 %fi to move the
FUNCTION SET
highlight bar (arrow) to TUNER SET
7 8 9 = INITIAL SET
“INITIAL SET”, then
0 4
press OK or SHUTTLE
PLUS #. PRESS (5,∞), THEN (OK)
PRESS (MENU) TO END
1 3 Select clock set

Press SHUTTLE PLUS INITIAL SET
%fi to move the = CLOCK SET
highlight bar (arrow) to GUIDE CHANNEL SET
“CLOCK SET”, then
press OK or SHUTTLE
18
3
2–7 PLUS #. SELECT WITH (5,∞) AND (OK)
PRESS (MENU) TO END
2–7

EN 11
Setting clock semiautomatically
— Semiauto Clock Set
6 Select D.S.T. mode
You have three choices:
AUTO– Select if you want to adjust your VCR’s
You can change the host channel/D.S.T. /time zone
clock automatically by the incoming
setting manually.
signal from the host channel. (Auto
First follow steps 1 to 3 on page 10, then go to the
Daylight Saving Time*)
following steps.
ON– Adjustment will be made by the built-in
clock itself.
4 Set Auto Clock to ON
Press SHUTTLE PLUS # CLOCK SET
OFF– Select when Daylight Saving Time does
not apply to you.
to move the highlight TIME DATE YEAR Press SHUTTLE PLUS # to move the highlight bar
bar to “AUTO CLOCK”, 1:00PM 12/24 02 TUE
AUTO CLOCK : ON to “D.S.T.”, then press SHUTTLE PLUS %fi
then press SHUTTLE HOST CH : AUTO (CATV) repeatedly until the desired setting is selected.
PLUS %fi so that “ON” D.S.T. : AUTO
TIME ZONE : AUTO
is selected.
7 Select time zone
PRESS (5,∞), THEN (OK)
PRESS (MENU) TO END
Then;
You can select the time zone automatically or
To select the host
manually.
channel — go to step 5.
Press SHUTTLE PLUS # to move the highlight bar
To select the D.S.T. mode — go to step 6.
to “TIME ZONE”, press SHUTTLE PLUS %fi
To select the time zone — go to step 7.
repeatedly until “AUTO” or the desired time zone
NOTE: is selected.
The time set previously will be erased when “AUTO Each time you press the button, the time zone
CLOCK”, “HOST CH”, “D.S.T.” or “TIME ZONE” changes as follows:
setting is changed.
= AUTO = ATLANTIC = EASTERN
= CENTRAL = MOUNTAIN = PACIFIC
5 Select host channel
You can either select “AUTO” or enter a PBS = ALASKA = HAWAII = (back to the beginning)
channel number.
Press SHUTTLE PLUS # to move the highlight bar NOTE:
to “HOST CH”, then press SHUTTLE PLUS %fi If an incorrect clock time is displayed by the Plug &
Play setting, you may be receiving the clock setting
until “AUTO” or the desired PBS channel number
data of a PBS channel from an adjacent time zone or
is selected.
from an incorrect PBS channel from a cable TV system.
NOTE: If you selected "AUTO" for the host channel in step 5,
be sure to select the correct time zone manually.
Some PBS channels do not transmit clock setting data.
8 Return to normal screen

Press MENU.
* Auto Daylight Saving Time

This function enables automatic adjustment of the VCR’s
clock at the start and end of Daylight Saving Time.
With Auto DST activated, . . . IMPORTANT
... on the first Sunday of April at 2:00 AM, the clock is Turn off the VCR after performing Semiauto Clock Set.
adjusted to 3:00 AM. ”Auto” will appear on the front display panel while the
... on the last Sunday of October at 2:00 AM, the clock is being set. The current clock time will appear
clock is adjusted to 1:00 AM. automatically when the clock setting is complete.

5 Set date
Press SHUTTLE PLUS %fi until the desired date
appears, then press OK or SHUTTLE PLUS #.
● Holding SHUTTLE PLUS %fi changes the date

in 15-day intervals.
1
4
2
5
3
6
2
6 Set year
Press SHUTTLE PLUS %fi until the desired year
appears, then press OK or SHUTTLE PLUS # twice.
7 8 9
0 4
7 Select D.S.T. mode
You can select either “ON” or “OFF”.
ON– Adjustment will be made by the built-in
clock itself.
OFF– Select when Daylight Saving Time does
1 not apply to you.
Press SHUTTLE PLUS %fi to select the desired
setting.
8 3
4–7 8 Start clock

Press MENU and normal screen appears.
To make corrections any time during the process

Press OK or SHUTTLE PLUS # repeatedly until the item
you want to change blinks, then press SHUTTLE PLUS
%fi.
4–7
Setting clock manually

— Manual Clock Set
First follow steps 1 to 3 on page 10, then go to the
following steps.
4 Set time
Press SHUTTLE PLUS CLOCK SET
%fi until the desired TIME DATE YEAR
time appears, then press – –:– –AM 1/ 1 02
AUTO CLOCK : ON
OK or SHUTTLE PLUS HOST CH : AUTO (CATV)
#. D.S.T. : AUTO
TIME ZONE : AUTO
PRESS (5,∞), THEN (OK)
PRESS (MENU) TO END
● Holding SHUTTLE PLUS %fi changes the time

in 30-minute intervals.
● When the time is entered manually, “AUTO
CLOCK” is automatically set to “OFF”, and
“HOST CH” and “TIME ZONE” disappear.

EN 13
Tuner Setting Setting channels
automatically — Auto Channel Set
Use Auto Channel Set only if channels have not been set
correctly by the Plug & Play setting. If you want to add
or delete channels, use Manual Channel Set (Z pg. 14).

Press MENU.
2 Access Tuner Set screen

%fi to move the FUNCTION SET
highlight bar (arrow) to = TUNER SET
INITIAL SET
1 2 3 “TUNER SET”, then
2
press OK or SHUTTLE
4 5 6
PRESS (MENU) TO END
7 8 9
0
3 Perform Auto Channel Set
4
You can automatically TUNER SET

set the receivable
BAND CATV
channels in your area in = AUTO CHANNEL SET
MANUAL CHANNEL SET
1 the order of their
frequencies.
Press SHUTTLE PLUS SELECT WITH (5,∞) AND (OK)
%fi to move the PRESS (MENU) TO END
highlight bar (arrow) to

AUTO CHANNEL SET
“AUTO CHANNEL
14 3
23 SET”, then press OK or

SHUTTLE PLUS #. SCANNING...
23 PRESS (MENU) TO END
NOTES:
● When Auto Channel Set is complete, “SCAN
COMPLETED” appears on screen.
● If the scan was unsuccessful, “SCAN COMPLETED–
NO SIGNAL” appears on screen. Check the
connections and start again.

Press MENU.
INFORMATION
The VCR selects the correct band (TV or CATV)
automatically during Auto Channel Set.
The selected band will be displayed on the right side of
“BAND” on the Tuner Set screen.

2 Access Tuner Set screen

Press SHUTTLE PLUS %fi to move the highlight
bar (arrow) to “TUNER SET”, then press OK or
SHUTTLE PLUS #.
1 2 3
3 Access Manual Channel Set screen
Press SHUTTLE PLUS TUNER SET
2 %fi to move the
4
BAND CATV
4 5 6 highlight bar (arrow) to AUTO CHANNEL SET
= MANUAL CHANNEL SET
“MANUAL CHANNEL
7 8 9
SET”, then press OK or
0 4 SHUTTLE PLUS #. SELECT WITH (5,∞) AND (OK)
PRESS (MENU) TO END
1
4 Add or skip desired channels
To add channels
1 Press the Number MANUAL CHANNEL SET
keys to input a
channel number you (CATV)
CH 45 ADD
want to add.
2 Press OK or
15 3
2–4 SHUTTLE PLUS # to

PRESS NUMBER KEY (0–9)
OR (5,∞), THEN (OK)
PRESS (MENU) TO END
set to “ADD”.
3 Repeat 1 and 2 to
add other channels.
2–4 To skip channels
1 Press the Number keys or SHUTTLE PLUS %fi
to input a channel number you want to skip.
2 Press OK or SHUTTLE PLUS # to set to “SKIP”.
3 Repeat 1 and 2 to skip other channels.

Press MENU.
Setting channels manually

— Manual Channel Set
You can add the channels you want or delete the
channels you do not want manually.

Press MENU.

BASIC PLAYBACK AND RECORDING EN 15
Basic This VCR can check the tape condition during playback
(and recording), and realizes the best possible pictures.
Playback 1 Load a cassette

Make sure the window side is up, the rear label
side is facing you and the arrow on the front of
the cassette is pointing towards the VCR.
Turn on the VCR and the TV, and select the VCR Do not apply too much pressure when inserting.
● The VCR turns on automatically.
● The counter is automatically reset to “0:00:00”.
● If the cassette's record safety tab has been
POWER 2 JOG dial removed and "REC SAFETY" is set to "ON",
playback begins automatically.
POWER
PLAY
REW
–
FF
+
2 Start playback
Press PLAY ( 3 ).
● Tape speed (SP or EP) is automatically detected.
CH– /+
PUSH / TURN
REC LINK A.DUB
● The S-VHS indicator lights up on the front

S VIDEO VIDEO (MONO)L—AUDIO—R 24HR QUICK
PROGRAM
SP EP
display panel when you play back a tape

recorded in S-VHS mode or in S-VHS ET mode
STOP/EJECT (Z pg. 40)
(7/0) ● If “VIDEO CALIBRATION” is set to “ON”
(default setting: Z pg. 37, 38), “VIDEO
CALIBRATION” appears on the screen, and this
POWER VCR checks the tape condition during
automatic tracking.
● If the tape ends during playback or fast-forward
1 2 3 search, the cassette indication “ ” blinks for
2
a few seconds and the VCR starts rewinding the
4 5 6
tape automatically.
7 8 9
To stop playback
0 4 Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 )
on the front panel.
To rewind the tape (when it is not running)
2 Press REW ( 1 ) (or turn the JOG dial on the front
1 panel to the left).
To fast-forward the tape (when it is not running)
REW ( 1 ) FF ( ¡ ) Press FF ( ¡ ) (or turn the JOG dial on the front panel
to the right).
To eject the tape
3
STOP ( 7 )
Press STOP/EJECT ( 7 / 0 ) on the front panel when the
To prohibit operations during playback (Mode Lock) tape is not running.
Press and hold OK on the Remote for more than 5 ● You can also eject the cassette with the VCR turned off.
seconds. " " and " " light up on the front display panel To turn off the VCR
(Z pg. 60). The playback will not be interrupted until Press POWER.
the recording end (unrecorded portion) or tape end is
reached (Z pg. 37, 41).
To resume the other operations, press and hold OK on
Clean the video heads using a dry
the Remote again for more than 5 seconds. cleaning cassette — TCL-2UX —
● When OK is pressed to set Mode Lock, the on-screen when:
display appears and the time counter remains on the • Rough, poor picture appears while a tape is played
TV screen. If the time counter is not necessary, set "ON back.
• The picture is unclear or no picture appears.
SCREEN (PLAY)" to "OFF" ( Z pg. 37, 39).
• “USE CLEANING CASSETTE” appears on the screen
(only with “ON SCREEN (PLAY)” set to “ON”: Z pg.
37, 39.)

16 EN BASIC PLAYBACK AND RECORDING (cont.)
Basic ● To display the VCR status including the tape remaining

time, the time counter and the clock time on the TV
screen, see “Showing on-screen display” (Z pg. 21).
● The approximate tape remaining time appears and the
Playback " " indicator lights on the front display panel.
● The tape remaining time is calculated based on the
tape speed (SP or EP) being used. The indicated
Features remaining time is only an estimate.
To reset the time counter, press C. RESET on the

Remote. The counter reading becomes “0:00:00”. It is
also reset when a tape is inserted.
Checking tape position

POWER
PLAY
REW
–
FF
+
B
CH– /+
PUSH / TURN
The tape position indicator
appears on screen in the
REC LINK A.DUB
PROGRAM
SP EP
following cases:
● When you change the VCR
operation mode from the B + + + E
STOP/EJECT stop mode to fast forward or
(7/0) rewind mode. COUNT 0:33:27
● When you perform an Index
Search (Z pg. 17) or Instant Review (Z pg. 18).
F –b The position of “ ” in relation to “B” (Beginning) or “E”
(End) shows you where you are on the tape.
E A
1 2 3
2 NOTES:
4 5 6 ● "ON SCREEN (PLAY)" must be set to “ON”, or the indicator
will not appear (Z pg. 37, 39).
7 8 9 ● It may take a few seconds for the tape position indicator to be
displayed.
C. RESET A 0 4
F –C
D –2 Playing back tape repeatedly
C — Repeat Play
1
D –1 You can play back a tape repeatedly.
F While playing back a tape, press and hold PLAY ( 3 )

–a, b, c C for more than 5 seconds.
F STOP ( 7 ) The play indicator ( # ) on the front display panel starts
–a
flashing slowly, and a tape will be played back
3
repeatedly.
To stop playback, press STOP ( 7 ) on the Remote or
STOP/EJECT ( 7 / 0 ) on the front panel.
● To select the returning point (recording end or tape
end), see "RETURN POINT" on page 41.
G To prohibit operations during Repeat Play (Mode Lock)
A Changing display information Press and hold OK on the Remote for more than 5
seconds. " " and " " light up on the front display panel
(Z pg. 60). The entire recording or entire tape will be
Press DISPLAY during playback.
played back repeatedly without any interruption.
Each time you press the button, the front display panel
To cancel Mode Lock, press and hold OK on the Remote
shows the time counter, tape remaining time and the
again for more than 5 seconds.
clock time in sequence.
● When OK is pressed to set Mode Lock, the on-screen
Time Counter Tape Remaining Time display appears and the time counter remains on the
TV screen. If the time counter is not necessary, set "ON
SCREEN (PLAY)" to "OFF" ( Z pg. 37, 39).
Clock Time

EN 17
Adjusting tracking condition F Automatic operations after
D — Tracking Adjustments rewinding — Next Function Memory
Automatic tracking adjustment The Next Function Memory “tells” the VCR what to do
This VCR automatically adjusts the tracking condition. after rewinding is complete.
Whenever you insert a tape and start playback, ● Ensure that the VCR is in stop mode.
automatic tracking starts working and continuously a– For Automatic Playback Start
analyzes the signal to enable optimum picture quality Press REW ( 1 ), then press PLAY ( 3 ) within
during playback. 2␣ seconds.
Manual tracking adjustment b– For Automatic Power Off
If automatic tracking cannot eliminate noises well during Press REW ( 1 ), then press POWER within
playback, use the manual tracking following the 2␣ seconds.
procedures below.
c– For Automatic Timer Standby
● You can also use the manual tracking during slow
Press REW ( 1 ), then press TIMER within
motion playback (Z pg. 27).
2␣ seconds.
1 Activate manual tracking
Press SP/EP on the Remote during playback. NOTE:
2 Eliminate the noises on the TV screen
It is not possible to select the Automatic Timer Standby function
if the cassette’s record safety tab is removed.
Press CH + or – on the Remote.
● Press it briefly for a fine adjustment, or press and
hold for coarse adjustment. Watch the screen and
G Locating beginning of
continue adjustment until optimum picture and recordings — Index Search
sound quality are achieved. Index codes are placed on the tape at the beginning of
● To reactivate automatic tracking, press SP/EP on each recording when recording on this VCR. You can
the Remote. The automatic tracking becomes find and automatically play back from the beginning of
active again. any recording using the Index Search function.
E Selecting monitor sound 1 Start search

— Audio Monitor While the tape is not running, press SHUTTLE PLUS
4 or ¢ on the Remote.
You can select the desired monitor sound.
While playing back a tape on which stereo sound or SAP 2 Access distant code
sound is recorded, press A. MONITOR on the Remote. To access a recording of 2 to 9 index codes away,
Each time you press the button, sound changes as follows: press SHUTTLE PLUS 4 or ¢ repeatedly until
the correct number is displayed on screen (only if
“ON SCREEN (REC)” is set to “ON” ; Z pg. 37, 39).
HI-FI HI-FI L HI-FI R
Playback begins automatically when the desired
NORM NORM recording is located.
HI-FI
Beginning of the current Current position Beginning of the 2nd next
HI-FI: Normally select this. program recorded on the tape program recorded
Previous Next
Hi-Fi sound is played back. program program 2nd next
HI-FI L: Sound on the left Hi-Fi channel is played back. recorded recorded
–2 –1 1 2 3
HI-FI R: Sound on the right Hi-Fi channel is played back. 4 ¢
NORM:Sound on the normal track is played back.
NORM HI-FI: ● If you want to find the very beginning of the
Both sounds on the Hi-Fi track and normal desired program, press REW ( 1 ) or FF ( ¡ )
track are mixed and played back. after playback starts.
NOTES: NOTE:
● The above indication appears when “ON SCREEN (PLAY)” is
set to “ON” (Z pg. 37, 39), though the monitor sound An index code is not placed on the tape when recording is
changes in sequence. resumed from recording pause.
● If the tape being played back has no Hi-Fi sound track, the
normal sound track will be heard regardless of this setting.
● If RF connection (Z pg. 7) is used for viewing pictures on the
TV, sound will be monaural even though you select “HI-FI”.
● You can also use the menu to select your desired monitor
sound. (Z pg. 40)

H Locating beginning of timer

I recordings — Instant Review
At the press of a button, you can turn on the VCR,
REW FF
rewind the tape and begin to view the most recent timer-
PLAY
POWER – +
recorded program.
CH– /+
PUSH / TURN

REC LINK A.DUB
24HR QUICK
PROGRAM
After ensuring that the VCR is turned off and that the
timer mode is disengaged, press REVIEW.
SP EP
● The VCR turns on, and rewinds to the index code

indicating the beginning of the last timer-recorded
program, then begins playback automatically.
● You can access a program of 2 to 9 index codes away
from the current position on the tape. If, for example,
you have 5 programs recorded and you want to watch
H the third one, press REVIEW three times.
1 2 3 ● If you want to find the very beginning of the desired program,
2
press REW ( 1 ) or FF ( ¡ ) after playback starts.
4 5 6 ● If the tape is already rewound when REVIEW is
7 8 9 pressed, it will play the tape from the beginning. It will
not fast-forward to an index code.
0 4
● The Instant Review function will also operate if the
VCR is turned on.
I Adjusting picture condition

1
— Digital TBC/NR
REW ( 1 ) FF ( ¡ ) The Digital TBC/NR (Time Base Corrector / Noise
Reduction) function removes jitter from fluctuating video
signals to deliver a stable picture even with old tapes
3
and rental tapes. The Digital 3-DNR (Noise Reduction)
function which cuts noise and reproduces clear pictures
is also linked to this function.
We recommend that you use the Digital TBC/NR
function when...
— playing back a tape recorded on a camcorder.
— playing back a tape repeatedly used.
— using this VCR as the player for editing.
Other Useful functions for playback
● Playback Resume Function Press DIGITAL TBC/NR on the front panel so that the
If there is a power outage during normal playback (or DIGITAL TBC/NR lamp lights up.
Series Playback), the playback will resume automatically Each time you press the button, this function turns on
when the power is restored to the VCR. (No setting is and off.
required for this function.)
● Video Calibration (Z pg. 38)

NOTES:
When this function is set to “ON”, this VCR checks the ● If you play back a tape recorded under poor TV reception
condition, the picture may happen to become more stable
condition of the tape in use during playback and
with Digital TBC/NR activated.
recording, and compensates to provide the highest- ● If you play back a tape on which certain types of signals
possible pictures. (using a PC or some character generators) have been recorded
with Digital TBC/NR activated, the playback picture may be
● Picture Control (Z pg. 38) distorted. In this case, deactivate Digital TBC/NR.
This function helps you to adjust the playback picture ● Digital TBC/NR and Video Stabilizer (Z pg. 39) cannot be
quality according to your preference. used at the same time; if you turn on Digital TBC/NR when
“VIDEO STABILIZER” is set to “ON”, Video Stabilizer will be
● Video Stabilizer (Z pg. 39) automatically turned “OFF”. Make sure Digital TBC/NR is
You can automatically correct vertical vibrations in the deactivated when you want to use Video Stabilizer.
picture when playing back unstable recordings made on
another VCR.

EN 19
Basic 2 Select recording channel
On the front panel:
Recording
Push the JOG dial, then turn it to the left or right.
On the Remote:
a– Press CH + or –.
or
b– Press the Number keys.
● If you connect the TV and the VCR only using
the RF connection, press TV/VCR on the Remote
JOG dial so that the VCR mode indicator lights on the front
POWER display panel, to view the program to be recorded.
PLAY ( 3 )
REW FF
3 Set tape speed
Press SP/EP to set the recording speed.
PLAY
4 Start recording
POWER – +
CH– /+
PUSH / TURN
On the front panel:

REC LINK A.DUB
PROGRAM
SP EP
Press REC ( ¶ ).
4 On the Remote:
While holding REC ( ¶ ), press PLAY ( 3 ).
PAUSE ( 8 )
● If “VIDEO CALIBRATION” is set to “ON”
STOP/EJECT (default setting: Z pg. 37, 38), this VCR checks
(7/0) the tape condition for about seven seconds,
then starts recording. This means that the first
seven seconds of the program will not be
recorded. If this is inconvenient for you, follow
POWER
the steps below:
TV/VCR 1 Press REC ( ¶ ) and PAUSE ( 8 ) to start
1 2 3 Video Calibration.
2 2 Then press PLAY ( 3 ) to start recording
4 5 6 2 –b after Video Calibration is complete.
7 8 9 To pause recording
Press PAUSE ( 8 ). To resume recording, press PLAY ( 3 ).
0 4
● Pressing REC ( ¶ ) on the front panel also resumes
recording.
2 –a To stop recording
Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 )
1
3 on the front panel.
To rewind the tape (when it is not running)
REW ( 1 ) FF ( ¡ )
Press REW ( 1 ) (or turn the JOG dial on the front
PAUSE ( 8 ) panel to the left).
4 3 To fast-forward the tape (when it is not running)
STOP ( 7 ) Press FF ( ¡ ) (or turn the JOG dial on the front panel
to the right).
This VCR can check the tape condition during recording To eject the tape
(and playback), and realizes the best possible pictures. Press STOP/EJECT ( 7 / 0 ) on the front panel when the
tape is not running.
● You can also eject the cassette with the VCR turned off.
1 Load a cassette
Make sure the record safety tab is intact. If not, To turn off the VCR
set "REC SAFETY" to "OFF" ( Z pg. 37, 41). Press POWER.
● You can also record onto a cassette without a It may be unlawful to record or play back
record safety tab by covering the hole with copyrighted material without the consent of the
adhesive tape before inserting the cassette. copyright owner.

Basic A Changing display information

Press DISPLAY during recording or recording pause.
Recording Each time you press the button, the front display panel
shows the time counter, tape remaining time, channel
number and the clock time in sequence.
Features Time Counter Tape Remaining Time
STOP/EJECT ( 7 / 0 ) Clock Time Channel No.
● To display the VCR status including the tape remaining

time, the time counter and the clock time on the TV
REW FF screen, see “Showing on-screen display” (Z pg. 21).
● The approximate tape remaining time appears and the
PLAY
POWER – +
CH– /+
PUSH / TURN
" " indicator lights on the front display panel.
REC LINK
DIGITAL TBC/NR
SP EP
VCR
A.DUB
INSERT
24HR QUICK
PROGRAM
REC PAUSE STOP/EJECT

● The tape remaining time is calculated based on the
tape speed (SP or EP) being used. The indicated
remaining time is only an estimate.
To reset the time counter, press C. RESET on the
B Remote. The counter reading becomes “0:00:00”. It is
also reset when a tape is inserted.
A B Recording on one tape

C –1 1 2 3 repeatedly
2
4 5 6 — Repeat Recording
You can record programs on one tape repeatedly.
7 8 9
While recording, press and hold PLAY ( 3 ) and
C. RESET 0 4 REC␣ (␣ ¶␣ ) on the Remote or REC ( ¶ ) on the front panel
for more than 5 seconds.
The record indicator on the front display panel starts
flashing slowly.
To stop recording, press STOP ( 7 ) on the Remote or
1
STOP/EJECT ( 7 / 0 ) on the front panel.
B To prohibit operations during Repeat Recording

STOP ( 7 ) (Mode Lock)
Press and hold OK on the Remote for more than 5
3
D (Z pg. 60). The recording will be performed repeatedly
without any interruption.
To cancel Mode Lock, press and hold OK on the Remote
Accidental erasure prevention
again for more than 5 seconds.
To prevent accidental recording on a recorded cassette,
remove its record safety tab. To record on it later, cover the
hole with adhesive tape, or set "REC SAFETY" to "OFF". display appears and the time counter will be recorded
(Z␣ pg. 37, 41) with your picture. If the time counter is not necessary,
set "ON SCREEN (REC)" to "OFF" ( Z pg. 37, 39).
Record safety tab

Note: You can also record onto the cassette even when the
tab is removed. (Z pg. 41)

EN 21
C Watching one program while
recording another
Other useful functions for recording
● Recording Resume Function
1 Engage TV mode If there is a power outage during recording (or timer
recording or Series Recording), the recording will resume
During recording...
automatically when the power is restored to the VCR. (No
● If you connect the TV and the VCR only using setting is required for this function.)
the RF connection (Z pg. 7) to view pictures
from the VCR ● Video Calibration (Z pg. 38)
Press TV/VCR on the Remote so that VCR mode When this function is set to “ON”, this VCR checks the
condition of the tape in use during playback and
indicator goes off from the front display panel.
recording, and compensates to provide the highest-
(The TV broadcast being recorded disappears.)
possible pictures.
● If you are using the AV connection (Z pg. 7) to
view pictures from the VCR, change the TV’s ● Second Audio Recording (Z pg. 40)
input mode from AV to TV. This VCR’s built-in MTS decoder enables reception of
Multichannel TV Sound broadcast.
2 Select channel for viewing To record a SAP program received, set “2ND AUDIO
Select the channel, you want to watch, on the TV. RECORD” to “ON” using the menu screen.
NOTES:
D Showing on-screen display When the channel is changed on the VCR;
● The “STEREO” indication appears on the screen for about
When “ON SCREEN (REC)” is set to “ON” (Z pg. 37, 5 seconds if the program is a stereo broadcast.
38), you can see the current VCR status on the TV ● The “SAP” indication appears on the screen for about
screen. 5␣ seconds if the program is a SAP broadcast.
● For more detailed information about the on-screen ● Both indications appear when a stereo program is
accompanied by SAP sound.
display, see page 61.
1 Display VCR status on TV screen
● S-VHS Recording Mode (Z pg. 40)
This VCR allows you to record on an S-VHS tape with VHS
During recording or CH 125 RECORD picture quality.
recording pause, press FRI 12:00:00 AM PAUSE
11/30/01 ]SP ● S-VHS ET (Z pg. 41)
OSD. STEREO
SAP This function allows you to record on VHS tapes with S-
All indications VHS picture quality. Tapes recorded using this function can
corresponding to the B + + + E
INDEX 1 be played back on a VCR equipped with the S-VHS ET
current VCR status are NORM REMAIN 10:00 function.
HI–FI COUNT –1:23:45
displayed for 5 seconds.
The time counter remains
on the screen indicating the elapsed time.
To prohibit operations during recording (Mode Lock)
● The indications will be recorded. If you do not
want to record the superimposed operational
indications on the screen, set “ON SCREEN
(Z pg. 60). No button will function and recording will
(REC)” to “OFF”. (Z␣ pg.␣ 37, 38)
not be interrupted until it completes.
2 Exit on-screen display To resume the other operations, press and hold OK on
the Remote again for more than 5 seconds.
Press OSD again.
NOTES: ● When OK is pressed to set Mode Lock, the on-screen
● If the VCR is in recording pause mode, “RECORD/PAUSE” is
display appears and the time counter will be recorded
always displayed (except when "DAY/TIME INSERT" is set to with your picture. If the time counter is not necessary,
"ON"). set "ON SCREEN (REC)" to "OFF" ( Z pg. 37, 39).
● The VCR status can be also displayed during playback.

22 EN SERIES PLAYBACK AND RECORDING
Series Playback
To REMOTE OUT
REMOTE
REMOTE
R
OUT
AUDIO
S
IN OUT L VHF/UHF
V TV OUT
I VIDEO
D
E
O
SR-V10U-1
Mini-plug
To REMOTE To cable
To S VIDEO OUT
IN AUDIO/ (Not supplied)
Audio/Video VIDEO
Cable OUT
S-Video Cable Mini-plug (Supplied)
(Supplied) cable
(Not supplied)
To
AUDIO/
VIDEO IN
To S VIDEO IN To REMOTE
OUT
To REMOTE IN
REMOTE
REMOTE
R
OUT
AUDIO
S
IN OUT L VHF/UHF
V TV OUT
I VIDEO
D
E
O
SR-V10U-2
To S VIDEO OUT To AUDIO/ VIDEO OUT
S-Video Cable (Supplied)
Audio/Video Cable (Supplied)
To S-Video Input To Audio/Video

Input
NOTE:
Series Playback is also possible using the front AUDIO/VIDEO
connectors.

EN 23
2 4 NOTE:
If there is a power outage during Series Playback, the playback
will resume automatically when the power is restored to the
VCR. (No setting is required for this function.)
REW FF
PLAY
To prohibit operations during Series Playback (Mode

POWER – +
CH– /+
Lock)
PUSH / TURN
REC LINK A.DUB


PROGRAM
SP EP
(Z pg. 60). The 2 cassettes will be played back
STOP/EJECT alternately without any interruption.
(7/0) To resume the other operations, press and hold OK on
the Remote again for more than 5 seconds.
Using two sets of SR-V10U, you can play back two
cassettes alternately as many times as you want. You can
display appears and the time counter remains on the
select the returning point for Series Playback (Z pg. 41)
TV screen. If the time counter is not necessary, set "ON
Use the buttons and controls on the VCR’s front SCREEN (PLAY)" to "OFF" ( Z pg. 37, 39).
panel for the Series Playback operations (except
when using Mode Lock).
1 Make connections
Connect two sets of SR-V10U and a TV using AV
cables as shown in the illustration on page 22.
● The mini-plug cable is a mono 3.5 mm mini-
plug to mono 3.5 mm mini-plug connector.
● When playing back S-VHS recordings, it is
recommended to use the S-VIDEO connection
to minimize picture degradation.
2 Turn on all components

After completing the connections, turn on all the
components.
● Set the TV to video input mode or A/V input
mode. Refer to the TV instruction manual.
3 Load cassettes
Insert the playback cassette into each SR-V10U.
● Set SR-V10U-2 to “AUX”. Press CH + or – to
select the input mode depending on the
connector being used -”L-1” for the rear
AUDIO/VIDEO IN connector, or “F-1” for the
front AUDIO/VIDEO input connector.
4 Start playback
Press PLAY ( 3 ) on either of SR-V10U. When the
playback reaches to the returning point (tape end
or recording end Z pg. 41), the other SR-V10U
successively starts to play. (The cassette will
automatically be rewound when the playback
stops.) Therefore, the cassettes loaded on two SR-
V10U will be played back alternately as many
times as you want.
To stop playback
Press STOP/EJECT ( 7 / 0 ) on the SR-V10U which is
playing back a cassette.

24 EN SERIES PLAYBACK AND RECORDING (cont.)
Series Recording
Camcorder or Another VCR
To S Video To Audio/Video Output

Output
Audio/Video Cable (Not supplied)
S-Video Cable (Not supplied)

To S VIDEO IN To AUDIO/ VIDEO IN To REMOTE OUT
REMOTE
Mini-plug cable
REMOTE
OUT
R
(Not supplied)
AUDIO
S
IN OUT L VHF/UHF
V TV OUT
I VIDEO
D
E
O
SR-V10U-1
To To AUDIO/
REMOTE VIDEO OUT
To S VIDEO OUT IN
Mini-plug cable
S-Video Cable (Supplied) (Not supplied) Audio/ Video Cable
(Supplied)
To
To S VIDEO IN REMOTE To AUDIO/ VIDEO IN
OUT
REMOTE
REMOTE
OUT
R
To REMOTE IN
AUDIO
S
IN OUT L VHF/UHF
V TV OUT
I VIDEO
D
E
O
SR-V10U-2
To S VIDEO OUT To AUDIO/ VIDEO OUT
To S Video Input
S-Video Cable (Supplied)
Audio/Video Cable (Supplied)

To Audio/Video Input
NOTE:
Select the correct input mode (“L-1” for the rear connector, “F-
1” for the front connector). (Z step 3)

EN 25
2 STOP/EJECT
(7/0) 5 Start recording
Press REC ( ¶ ) on either of SR-V10U. When the
tape remaining time reaches to 2 minutes while
recording, the other SR-V10U successively starts
PLAY
REW FF
to record. Therefore, recording will be continued

POWER – +
CH– /+
PUSH / TURN
onto cassettes loaded on two SR-V10U
REC LINK A.DUB
24HR QUICK
alternately.
PROGRAM
SP EP
● The cassette will automatically be rewound

when the recording stops.
● Replace the cassette after rewound if you want
5 to continue to record onto another cassette.
Using two sets of SR-V10U, a long recording will be To stop recording

possible (such as camcorder recording, another VCR Press STOP/EJECT ( 7 / 0 ) on the SR-V10U which is
playback or TV broadcast). recording.
Use the buttons and controls on the VCR's front
panel for the Series Recording operations (except To prohibit operations during Series Recording (Mode
when using Mode Lock). Lock)
1 Make connections
Connect two sets of SR-V10U to other
(Z pg. 60). The picture will be recorded onto the
equipment, antenna or cable as shown in the cassettes alternately without any interruption.
illustration on page 24. To resume the other operations, press and hold OK on
●The mini-plug cable is a mono 3.5 mm mini- the Remote again for more than 5 seconds.
plug to mono 3.5 mm mini-plug connector. ● When OK is pressed to set Mode Lock, the on-screen
● When connecting a camcorder or another VCR display appears and the time counter will be recorded
with an S-VIDEO output connector as recording with your picture. If the time counter is not necessary,
source, it is recommended to use the S-VIDEO set "ON SCREEN (REC)" to "OFF" ( Z pg. 37, 39).
connection to minimize picture degradation.
NOTES:
2 Turn on all components
After completing the connections, turn on all the
● Series Recording is also possible using the front AUDIO/
VIDEO connectors.
● When recording a TV broadcast, tune in the same channel on
components.
both SR-V10U.
● Set the TV to video input mode or A/V input ● If you do not want to record the operational indications on
mode. Refer to the TV instruction manual. the screen during Series Recording, set both “ON SCREEN
(PLAY)” and “ON SCREEN (REC)” to “OFF”. (Z␣ pg.␣ 37, 38)
3 Set recording VCR's input mode

Set to “AUX“. Press CH + or – to select the input
● If there is a power outage during Series Recording, the
recording will resume automatically when the power is
restored to the VCR. (No setting is required for this function.)
mode depending on the connector being used –
“L-1“ for the rear AUDIO/VIDEO IN connector,
or “F-1“ for the front AUDIO/VIDEO input
connector.
4 Prepare for recording

Insert the recording cassette into each SR-V10U,
and prepare the playback source.
NOTE:
If you do not want to display the superimposed
indication on the screen during recording, set “ON
SCREEN (REC)“ to “OFF“ (Z pg. 37, 38). If the
playback equipment has a superimpose/OSD disable
feature, set its superimpose or display feature to “OFF“
as well.

26 EN SPECIAL EFFECT PLAYBACK
Special Effect A Locating particular scene

rapidly — Picture Search
Playback 7 High-Speed Picture Search:
You can rapidly locate a particular scene on the tape.
On the front panel:
A B D E Possible during normal playback.
To do forward picture search, turn the JOG dial quickly
PLAY ( 3 ) to the right.
To do reverse picture search, turn the JOG dial quickly
to the left.
● If you release the dial, picture search continues.
PLAY
REW FF
On the Remote:
POWER
Possible during normal playback or still picture

– +
CH– /+
PUSH / TURN

REC LINK A.DUB
24HR QUICK
playback.
PROGRAM
DIGITAL TBC/NR
SP EP
VCR INSERT REC PAUSE STOP/EJECT
To do forward picture search, press FF ( ).
To do reverse picture search, press REW ( ).
● If you press and hold the button for more than
B D 2␣ seconds, simply releasing it cancels the picture
search, and normal playback resumes.
To resume normal playback, press PLAY ( 3 ).
F 7 Variable-Speed Picture Search:

Possible during normal playback.
1 2 3 You can change the speed of picture search.
2
4 5 6
How to use the JOG dial on the front panel:
7 8 9 Turn the JOG dial to the right (forward search) or to the
left (reverse search).
0 4
Each time the JOG dial passes a click position, picture
search speed changes (see the diagram below).
If you release the dial, picture search continues.
● The speed of picture search is determined by the
1
C number of click stops of the JOG dial.
A A
PLAY ( 3 )
B v e rs e
Slow
3
Re low motio
D rs
e s
tion (2 step
n No
Pl r
mo steps) s) a
m
y
p ve
al
la
y
Re
(2
Forw h
searc
( 4 ste
A D
Reverse
search
(3 steps)
ard
ps)

EN 27
How to use the SHUTTLE PLUS buttons on the Remote: Viewing still picture frame by
To do forward picture search, press SHUTTLE PLUS D frame — Frame-by-Frame Playback
¢ repeatedly.
Each time you press the button, the search speed On the front panel:
increases. During normal playback:
● To decrease the speed while forward picture search Push the JOG dial or press PAUSE ( 8 ) to pause.
(toward normal playback, then reverse picture search), To advance a still picture, turn the JOG dial to the right.
press SHUTTLE PLUS 4 repeatedly. To reverse a still picture, turn the JOG dial to the left.
To do reverse picture search, press SHUTTLE PLUS 4 On the Remote:
repeatedly. During normal playback:
Each time you press the button, the search speed Press PAUSE ( 8 ) to pause.
increases while reverse picture search. To advance a still picture, press SHUTTLE PLUS ¢ (or
● To decrease the speed while reverse picture search PAUSE ( 8 )) repeatedly.
(toward normal playback, then forward picture To reverse a still picture, press SHUTTLE PLUS 4
search), press SHUTTLE PLUS ¢ repeatedly. repeatedly.
To resume normal playback, press PLAY ( 3 ). To resume normal playback, press PLAY ( 3 ).
TV CH +
E Viewing slow motion picture

SHUTTLE — Slow Motion Playback
PLUS
TV
+
VO
On the front panel:

L
L
O
– V
TV
TV CH –
During normal playback:
Reverse Forward Turn the JOG dial to the first or second click-stop to the
Reverse Reverse Reverse Slow Normal Forward left (forward slow motion) or to the third or fourth click-
search play slow motion motion Play search stop to the left (reverse slow motion) so that slow motion
3 steps 2 steps 2 steps 4 steps playback starts. If you release the dial, slow motion
playback continues.
● Holding PAUSE ( 8 ) for more than 2␣ seconds also
starts forward slow motion playback.
B Viewing still picture On the Remote:
— Still Picture Playback ● During normal playback:
On the front panel: Press SHUTTLE PLUS 4 to decrease the playback
Push the JOG dial during normal playback. speed.
Each time you press the button, the speed decreases
On the front panel or the Remote:
(toward reverse slow motion playback, then reverse
Press PAUSE ( 8 ) during normal playback.
picture search).
Playback is freezed and a still picture appears.
To resume normal playback, press PLAY ( 3 ). starts forward slow motion playback.
NOTE: To resume normal playback, press PLAY ( 3 ).

To obtain a noiseless still picture, it may be necessary to adjust
tracking in slow motion playback before starting still picture ● During still picture playback:
playback. Press and hold SHUTTLE PLUS ¢ to start forward (or
SHUTTLE PLUS 4 to start reverse) slow motion
playback. When you release the button, slow motion
C Skipping unwanted portions playback stops and a still picture appears.

— Skip Search starts forward slow motion playback.
You can skip over (view at high speed) unwanted
portions of the tape. To resume normal playback, press PLAY ( 3 ).
Press SKIP SEARCH once to 4 times during playback.

Each press initiates a 30-second period of high speed NOTE:
playback (up to 2 minutes). When the specified portion Manual tracking is possible during slow motion playback.
of the tape is skipped, normal playback resumes During slow motion playback, simply press CH + or – on the
automatically. Remote to adjust tracking.
To return to normal playback during Skip Search, press
PLAY ( 3 ).

28 EN TIMER RECORDING
VCR Plus+ ® Timer recording allows you to program the VCR to

automatically record a broadcast at some future time.
Up to 8␣ timer recording programs can be made using
Timer VCR Plus+ timer programing, Express timer programing

(Z pg. 32) or 24HR quick programing method
(Z␣ pg.␣ 34) as far as a year in advance.
Programing The VCR Plus+ timer programing system eliminates the

need to input channel, date, start and stop time data
when programing timer recording settings. Simply key in
the PlusCode number for the TV broadcast you wish to
record and the VCR’s timer will be automatically
Turn on the VCR and the TV, and select the VCR programed. (The PlusCode programing numbers are the
channel 3 or 4 (or AV mode) on the TV. numbers next to the program in most TV listing.)
1 Load a cassette
Make sure the record safety tab is intact. If not,
set "REC SAFETY" to "OFF" ( Z pg. 37, 41).
● The VCR turns on, and the counter is reset,
automatically.
● You can also record onto a cassette without a
POWER record safety tab by covering the hole with
adhesive tape before inserting the cassette.
1 2 3
4 5 6
2
34 2 Access PlusCode No. screen

Press PROG. on the
PLUSCODE NO.
DAILY Remote.
7 8 9 WEEKLY
● The clock must be set
CANCEL 0 4
8 to access the
PlusCode No. screen. PRESS NUMBER KEY (0–9)
4
PRESS (+/–) TO SET
STOP +/– If you have not set the EXPRESS PROGRAMMING
PRESS (PROG.) TO END
clock, the Main Menu
27 1
6
screen appears after
an error message is displayed. Refer to page 8
for the Plug & Play setting or page 10 for the
clock setting procedure.
3
347 3 Enter PlusCode number PLUSCODE NO.
Press the appropriate
4 Number keys to input
123
the PlusCode number
printed in the TV
listings for the TV
broadcast you wish to THEN (OK)
record, then press OK. PRESS (PROG.) TO END
Then;
If the Guide Channel Set screen appears
— go to step 4.
If the VCR Plus+ Program screen appears
— go to step 5.
● To make corrections, press CANCEL and input
the correct PlusCode number.

EN 29
4 Input receiving channel number
The guide channel GUIDE CHANNEL SET
Press PROG. or OK.
number, which is “PROGRAM COMPLETED” appears on the
GUIDE CH: 12
assigned to the TV or VCR CH : ––– screen for about 5 seconds, then normal screen
cable station for the appears.
PlusCode number that • If “PROGRAM NOT COMPLETED PROGRAM
you entered in step 3, OR (5,∞), THEN (OK) OVERLAP” appears, you have another program
will appear PRESS (PROG.) TO END
overlapping the program you have just made.
automatically on the The Program Check screen appears and
Guide Channel Set screen. conflicting programs will start blinking.
Press the Number keys (or CH +/– or SHUTTLE You can now correct the conflicting programs.
PLUS %fi) to input the number of the channel on See “When programs overlap each other” on
which the broadcast for the PlusCode number is page 36.
received on the VCR, then press OK.
● The Guide Channel Set screen appears only
when you input the PlusCode number of a 8 Engage timer recording standby mode
Press TIMER.
station for which the guide channel number has The VCR turns off automatically and “‰” is
not been set previously. displayed on the front display panel.
● If you receive your channels through a cable
box, select the cable box output channel — the To use the VCR while it is in timer recording standby
channel on which you view the cable box
programs on the TV. mode
Press TIMER to cancel the timer recording standby
mode, then press POWER to turn on the VCR.
5 Check program date
The PlusCode number you entered and the
DO NOT forget to put the VCR into timer recording standby
mode again by pressing TIMER after you use the VCR;
corresponding timer PROGRAM 1 otherwise, you cannot record the broadcasts you want.
recording program is (PLUSCODE NO. 12345678)
START STOP ● When “AUTO TIMER” is set to “ON” (Z pg. 37, 38) ,
displayed on the 8:00PM = 10:00PM
DATE CH the timer recording standby mode is automatically
Program screen. Check 12/24/00 12 SP engaged when the VCR is turned off. It is temporarily
to make sure it is SUN
PRESS (8=DAILY, 9=WEEKLY canceled when the VCR is turned on. You do not have to
accurate. STOP+/– = STOP TIME, SP/EP)
press TIMER to engage or disengage the timer recording
● To change the stop standby mode.
time, press STOP +/–.
● To timer-record daily (Sunday–Saturday) or
weekly serials, press DAILY (number “8”) or IMPORTANT
WEEKLY (number “9”). “DAILY” or “WEEKLY” If you have moved to a different area or if a broadcasting
appears on the Program screen. station’s channel number has been changed, the wrong
Pressing the button again makes each VCR CH number will be displayed on the Program screen
corresponding display disappear. in step 5. When this happens, set the correct guide
channel number for that station. (Z pg. 30, “Changing
● If you made a mistake, press CANCEL to access
VCR Plus+ Setting”)
the PlusCode No. screen again and input the
correct PlusCode number.
● If an incorrect PlusCode number or the one for
a broadcast already finished has been inputted, NOTES:
“ERROR” is displayed for about 5 seconds, then ● In case of a power failure after programming, the recorder's
the PlusCode No. screen reappears. memory backup keeps your selections (if the lithium battery is
not exhausted).
● To timer-record cable channels received through a cable box,
6 Set tape speed
Press SP/EP.
be sure to keep the cable box turned on with the correct
channel selected.

30 EN TIMER RECORDING (cont.)
Changing IMPORTANT
If you have moved to a different area or if a broadcasting
VCR Plus+®
station’s channel number has been changed, the wrong
VCR CH number will be displayed on the
Program screen (Z step 5 on page 29). When this
happens, perform the following steps to set the correct
Setting guide channel number for that station.
Turn on the VCR and the TV, and select the VCR To ensure that VCR Plus+ timer recording operates
channel 3 or 4 (or AV mode) on the TV. correctly, it is necessary to set the VCR Plus+ “Guide
Channel Set” for each station. Read the following
information carefully.
VCR Plus+ guide channel matching

The VCR Plus+ programing system assigns a VCR Plus+
guide channel to the TV channels and the cable
channels. These guide channel numbers are also called
1 2 3 the VCR Plus+ channel codes. Most TV listings have a
2 section, usually a chart, indicating the guide channel
4 5 6 45 numbers assigned to each station. For accurate VCR
7 8 9 Plus+ programing, the VCR Plus+ guide channel number
for each station should match the channel number on
0 4 which it is received in your area.
NOTES:
1
● In many instances, the VCR Plus+ guide channel numbers for
cable and broadcast TV stations DO NOT match the channel
number on which it is received by your VCR or cable box.
Check your TV listing, or contact your cable supplier for
details.
● Many TV stations can be viewed on cable. Check your TV
16 3
2–5 listing, or contact your cable supplier for details.
2–5

EN 31
Press MENU. 5 Input receiving channel number
Press the Number keys
(Ex.) If WNJU(Ind.) is
or SHUTTLE PLUS %fi
received on channel 47
2 Access Initial Set screen
to input the number of
the channel on which GUIDE CHANNEL SET
%fi to move the the guide channel’s GUIDE CH : 6

FUNCTION SET VCR CH : 47
highlight bar (arrow) to TUNER SET broadcasts are received,
= INITIAL SET then press OK or
“INITIAL SET”, then
press OK or SHUTTLE SHUTTLE PLUS #. PRESS NUMBER KEY (0-9)
PLUS #. PRESS (5,∞), THEN (OK) ● Repeat steps 4 and 5 OR (5,∞), THEN (OK)
PRESS (MENU) TO END
PRESS (MENU) TO END
for each instance.
● If you receive your channels through a cable
3 Access Guide Channel Set screen

Press SHUTTLE PLUS INITIAL SET
box, select the cable box output channel — the
%fi to move the programs on the TV.
CLOCK SET
highlight bar (arrow) to = GUIDE CHANNEL SET
“GUIDE CHANNEL
SET”, then press OK or 6 Return to normal screen
Press MENU.
SHUTTLE PLUS #. SELECT WITH (5,∞) AND (OK)
PRESS (MENU) TO END
4 Input guide channel number

Press the Number keys (Ex.) When inputting the
or SHUTTLE PLUS %fi guide channel number 6
to input the VCR Plus+ for WNJU(Ind.)
guide channel number GUIDE CHANNEL SET
as shown in the TV
GUIDE CH : 6
listing, then press OK or VCR CH : – – –
SHUTTLE PLUS #.
PRESS NUMBER KEY (0-9)
OR (5,∞), THEN (OK)
PRESS (MENU) TO END

Express Timer You can directly program the VCR’s timer to record up to
8 programmes, as far as a year in advance. Remember,
the clock must be set before you can program the timer
Programing (Z pg. 8 or 10).
1 Load a cassette
Turn on the VCR and the TV, and select the VCR set "REC SAFETY" to "OFF" ( Z pg. 37, 41).
channel 3 or 4 (or AV mode) on the TV. ● The VCR turns on, and the counter is reset,
automatically.
● You can also record onto a cassette without a
record safety tab by covering the hole with
adhesive tape before inserting the cassette.
2 Access PlusCode No. screen

Press PROG..
POWER
3 Access Program screen
Press START +/– once. PROGRAM 1
(If no program is stored, START STOP
1 2 3 “PROGRAM 1” – –:– –AM = – –:– –AM
2
DATE CH
4 5 6 appears.) – –/– –/– – – – – SP
DAILY
7 8 9 PRESS (+/–, SP/EP, 8=DAILY,
WEEKLY 9=WEEKLY), THEN (0K)
0
0 4
34 7
5 6 4 Set program start time
Press START +/–
29
1
PROGRAM 1
8 repeatedly to enter the
START STOP
time you want 8:00 AM = – –:– –AM
recording to start. DATE CH
– –/– –/– – – – – SP
● Press and hold START PRESS (+/–, SP/EP, 8=DAILY,
9
3
+/– to increase the 9=WEEKLY), THEN (0K)
time in 30-minute
intervals.
5 Set program stop time

Press STOP +/– repeatedly to enter the time you
want recording to stop.
● Press and hold STOP +/– to increase the time in
30-minute intervals.
6 Set program date

Press DATE +/–. (The current date is displayed on
the screen. The date you enter appears in its
place.)
7 Set channel number

Press CH +/–.
● Holding down CH +/– rapidly changes the
channel numbers.
● If you receive your programs through a cable
box, select the cable box output channel — the
programs on the TV.

EN 33
8 Set tape speed
Press SP/EP to set the tape speed.
NOTES:
● In case of a power failure after programming, the recorder's
memory backup keeps your selections (if the lithium battery is

Press PROG. or OK.
not exhausted).
● Programs that start after midnight must have the next day’s
date.
“PROGRAM COMPLETED” appears on the ● After timer recording is completed, the VCR turns off
screen for about 5 seconds, then normal screen automatically.
appears. ● You can program the timer recording while a regular
• If “PROGRAM NOT COMPLETED PROGRAM recording is in progress.
OVERLAP” appears, you have another program ● To timer-record cable channels, be sure to keep the cable box
overlapping the program you have just made. turned on with the correct channel selected.
The Program Check screen appears and
conflicting programs will start blinking.
You can now correct the conflicting programs.
See “When programs overlap each other” on
page 36.
0 Engage timer recording standby mode

Press TIMER.
The VCR turns off automatically and “‰” is
displayed on the front display panel.
To timer-record daily (Sunday–Saturday) or weekly

serials
Press DAILY (number “8”) or WEEKLY (number “9”)
anytime during steps 3 through 9.
“DAILY” or “WEEKLY” appears on the Program screen.
● Pressing the button again makes the corresponding
indication disappear.
To use the VCR while it is in timer recording standby

mode
Press TIMER to cancel the timer recording standby
mode, then press POWER to turn on the VCR.
DO NOT forget to put the VCR into timer recording
standby mode again by pressing TIMER after you use the
VCR; otherwise, you cannot record the broadcast you
want.
● When “AUTO TIMER” is set to “ON” (Z pg. 37, 38),
the timer recording standby mode is automatically
engaged when the VCR is turned off. It is temporarily
canceled when the VCR is turned on. You do not have
to press TIMER to engage or disengage the timer
recording standby mode.

24HR Quick You can program a timer recording that starts within
24␣ hours. Up to 8␣ timer recording programs can be
made as far as a year in advance. Remember, the clock
Programing must be set before you can program the timer (Z␣ pg.␣ 8
or␣ 10).
1 Load a cassette
JOG dial cover the hole with adhesive tape, then load it
into the VCR.
● The VCR turns on, and the counter is reset,
automatically.
2 Access 24HR quick program display.

REW FF
PLAY
POWER – +
CH– /+
PUSH / TURN
Push 24HR QUICK PROGRAM. “ ” and start
REC LINK
DIGITAL TBC/NR
SP EP
VCR
A.DUB
INSERT
24HR QUICK
PROGRAM

time start blinking on the display panel.
Program start time indicator
24HR QUICK
PROGRAM
3 Set program start time

Turn the JOG dial to the left or right. Then, push
the JOG dial. “ ” and start time start blinking on
NOTES: the display panel.
Program start time indicator
● If “Err” appears on the display panel, repeat the steps again.
● When a menu screen is shown, you cannot use 24HR quick
programing function. Press MENU to return to normal screen,
and try again.
● You can use 24HR quick programing function also when the
● One click stop of the JOG dial changes the
VCR is turned off.
time in 5-minute intervals.
● For 24HR quick programing function, the program overlap
warning display does not appear even if some programs
overlap each other.
● In case of a power failure after programming, the recorder's
4 Set program stop time
Turn the JOG dial to the left or right. Then, push
memory backup keeps your selections (if the lithium battery is the JOG dial and channel number will start
not exhausted). blinking.
Program stop time indicator
● One click stop of the JOG dial changes the

time in 5-minute intervals.
5 Set channel number

Turn the JOG dial to the left or right.
Timer warning display
A warning appears on the
TV screen to tell you that
–WARNING–
the timer-recording is to TIMER RECORDING
TO START SOON
● You can cancel the setting at any time by
start in 5␣ minutes if you (CANCEL) pressing and holding the JOG dial for more
are not in the timer
than 3 seconds. Repeat from the step 3.
recording standby mode at
that time. Press TIMER to
put the VCR into timer
recording standby mode. To clear the display, press
6 Engage timer recording standby mode
Press 24HR QUICK PROGRAM.
The VCR turns off automatically and “‰” is
CANCEL on the Remote.
displayed on the front display panel.

EN 35
A Checking program settings
1 Disengage timer
Press TIMER, then press POWER.
● When “AUTO TIMER” is set to “ON” (Z pg. 37,
38), you do not have to press TIMER.
A –1
2 Access Program Check screen
Press PROG. CHECK. PR START STOP CH DATE
1 8:00P 10:00 12 12/24
2 10:00A 10:45 40 12/25
1 2 3 3 11:30P 1:00 125 12/25
2 4
4 5 6 5
6
7
7 8 9 8
PRESS (CHECK) TO NEXT
B –2 0 4
A –1 B –4
B –2 Press PROG. CHECK again to check more detailed
information. Each time you press PROG. CHECK,
the next program’s Program screen appears. When
A –2, 3 1
B –2 all Program screens are shown, normal screen

B –3 resumes.
Canceling or changing program

3 B settings

Repeat steps 1 to 3 above.
2 Cancel or change program setting

To cancel a program, press CANCEL when the
Program screen you do not want is shown.
To change a program, press the appropriate button:
START+/–, STOP+/–, DATE+/–, CH+/–, and/or SP/
EP when the Program screen on which you want to
make changes is shown.

Press PROG. CHECK as many times as necessary
Other Useful functions for timer recording until no Program screen is shown.
You can also use the following functions for timer
recording.
4 Reengage timer recording standby mode
Press TIMER.
● Auto Timer (Z pg. 38) ● When “AUTO TIMER” is set to “ON” (Z pg. 37,
When “AUTO TIMER” is set to “ON”, the timer recording 38), the timer recording standby mode
standby mode is automatically engaged when the VCR is automatically resumes when you turn off the
turned off. It is temporarily canceled when the VCR is
VCR.
turned on. You do not have to press TIMER to engage or
disengage the timer recording standby mode.
● Auto SP = EP Timer (Z pg. 39)

If there is not enough tape to record the entire broadcast
for recording in SP mode, the VCR automatically switches
to EP mode to allow complete recording. This feature is
especially handy when recording a broadcast of more than
2 hours in length.

3 Cancel or change program setting

To cancel a program, PROGRAM 4
press CANCEL when the START STOP
Program screen you do 9:00 PM = 10:00PM
DATE CH
not want is shown. 12/24/00 10 SP
1 2 3 “PROGRAM SUN
2 PRESS (CANCEL) TO CANCEL
4 5 6 COMPLETED” appears on PRESS (OK) TO CONFIRM
the screen for about
7 8 9 5␣ seconds, then normal
C –3 0 4
screen appears.
To change a program, press the appropriate button:
C –3
START+/–, STOP+/–, DATE+/–, CH+/–, and/or SP/
EP when the Program screen on which you want to
make changes is shown, then press OK.
1
“PROGRAM COMPLETED” appears on the screen
C –3
for about 5 seconds, then normal screen appears.
NOTE:
If the overlap is not yet solved or another overlap occurs
with the timer program setting made last after making
3
C –3 correction on a program, the conflicting programs will be
shown on the Program Check screen again. Repeat the
C –2 above steps again until the overlap is solved.
C –2
ATTENTION
If there is a conflict in the timer schedule and one program
C When programs overlap each overlaps with another, only the parts shown below in gray
other will be recorded.
If “PROGRAM NOT COMPLETED PROGRAM Pattern 1: The program with the lower program
OVERLAP” appears, you have another program number will be recorded.
overlapping the program you have just made. 10:00 11:00 12:00
The Program Check screen appears and conflicting Program 1 CH10
programs will start blinking. Program 2 CH40 Not recorded
PR START STOP CH DATE

1 8:00P 11:00 12 12/24
Pattern 2: The program starting earlier will be
PROGRAM NOT COMPLETED 2 10:00A 10:45 40 12/25 recorded.
3 11:30P 1:00 125 12/25
PROGRAM OVERLAP 4 9:00P 10:00 10 12/24 10:00 11:00 12:00
5 Program 1 CH10
6
7 Program 2 CH40 Not recorded
8
(5,∞), THEN ( 3) (PROG.) : END Pattern 3: The program starting earlier will be
recorded, followed by the remaining portion
EX. Program 1 (you have just made) and Program 4 of the other program.
overlap each other 10:00 11:00 12:00
Program 1 CH10
1 Confirm overlapping programs Program 2 CH40
Overlapping programs blink on the screen.
Not recorded
2 Select program to modify
Press SHUTTLE PLUS %fi, then press SHUTTLE
PLUS #.
• You can only select one of the overlapping
programs.
NOTE:
If you do not mind this overlap, press PROG. to finish the
timer program setting. See “ATTENTION” to the right.
Without doing anything for about 1 minute, the VCR will
finish the timer programing.

OTHER USEFUL FUNCTIONS EN 37
Useful Function You can use the other useful function settings on the
Function Set screen by following the procedure
described below.
Settings ● For the functions you can set on the Function Set
screen, see pages 38 to 41.
Press MENU.
2 Access Function Set screen
%fi to move the
= FUNCTION SET
highlight bar (arrow) to TUNER SET
INITIAL SET
“FUNCTION SET”, then
press OK or SHUTTLE
PRESS (MENU) TO END
1 2 3
4 5 6
2
3 Select Function.
Press SHUTTLE PLUS %fi to move the highlight
7 8 9
bar (arrow) to the function you want to set.
0 4 FUNCTION PREVIOUS PAGE PREVIOUS PAGE

= VIDEO CALIBRATION =ON
DIGITAL R3 = REAR AUX INPUT VIDEO
PICTURE CONTROL AUTO
VIDEO STABILIZER S-VHS ET
OFF OFF
AUTO TIMER OFF
2ND AUDIO RECORD RETURN POINT TAPE END
OFF
ON SCREEN (REC) AUDIO MONITOR DAY/TIME INSERT
HI-FI OFF
ON SCREEN (PLAY) S-VHS MODE REC
ON SAFETY ON
AUTO SP=EP TIMER FRONT AUX INPUT DAILY T. RECORD NORM
1
NEXT PAGE NEXT PAGE
SELECT WITH (5,∞) AND (OK)
SELECT WITH (5,∞) ANDSELECT
(OK) WITH (5,∞) AND (OK)
PRESS (MENU) TO END PRESS (MENU) TO END PRESS (MENU) TO END
4 Change setting
Press OK or SHUTTLE PLUS #.
15 3
24
Press MENU.
23

38 EN OTHER USEFUL FUNCTIONS (cont.)
* The default setting is bold in the table below.
m VIDEO CALIBRATION When this function is set to “ON”, this VCR checks the condition of the
ON tape in use during playback and recording, and compensates to provide
OFF the highest-possible pictures. This takes place whenever you play back a
tape or start recording after inserting a tape.
NOTES:
● During playback, this function is always working even though “VIDEO
CALIBRATION” appears just at the beginning of automatic tracking.
● During recording, this function works only for the first EP recording and the first
SP recording on an inserted tape.
For timer recording, this function checks the tape condition both for the SP
recording and the EP recording before the first timer recording starts.
● When you play back rental tapes or tapes recorded on other VCRs, set this
function either “ON” or “OFF” whichever gives you the best picture.
m PICTURE CONTROL This function helps you to adjust the playback picture quality according
to your preference.
AUTO (NORM): Normally select
this. Picture quality is
adjusted automatically. NOTES:
When “VIDEO ● When you select “EDIT”, “SOFT” or “SHARP”, the selected mode will not
CALIBRATION” is “OFF”, change until you select again.
● Select "EDIT" when you are editing tapes (Z pg. 45, 46, and 49). After you
“NORM” will appear instead
finish editing the tapes, select “AUTO” (“NORM” when “VIDEO
of “AUTO”. CALIBRATION” is “OFF”.)
EDIT: Minimizes picture
degradation during editing
(recording and playback).
SOFT: Reduces image
coarseness when viewing
overplayed tapes
containing much noise.
SHARP: Clearer, sharper-edged
picture when viewing
images with much flat,
same-colored surfaces
such as cartoons.
m AUTO TIMER ● When this function is set to “ON”:

ON The timer recording standby mode is automatically engaged when the
OFF VCR is turned off. It is temporarily canceled when the VCR is turned
on. You do not have to press TIMER to engage or disengage the timer
recording standby mode.
● When this function is set to “OFF”:
You have to press TIMER to engage or disengage the timer recording
standby mode.
m ON SCREEN (REC) When this function is set to “ON”, all the indications displayed on
ON screen will be recorded. If you do not want to record the indications,
OFF select “OFF”. (Z pg. 21)
NOTE:
● The setting you have made is kept in memory. Even if the VCR is unplugged or
the power failure occurs, it will resume every time you turn on the VCR. (Z pg.
9)
Refer to page 37 for setting procedures.

EN 39
m ON SCREEN (PLAY) When this function is set to “ON”, various VCR status information (on-screen
ON display) appears on the screen during playback.
OFF
NOTES:
● When you use this VCR as the playback VCR for editing a tape, be sure to set this
function to “OFF”; otherwise, the VCR status information (on-screen display) will be
recorded on the edited tape.
● If you select a channel on which no signal is received, the channel number is
displayed regardless of this function setting.
● The setting you have made is kept in memory. Even if the VCR is unplugged or the
power failure occurs, it will resume every time you turn on the VCR. (Z pg. 9)
m AUTO SP = EP TIMER When this function is set to “ON”, the VCR automatically switches to EP
ON mode to allow complete recording if there is not enough tape to record the
OFF entire program while timer-recording in SP mode.
For Example . . .
Recording a program of 140 minutes in length onto a 120-minute tape
Approximately 110 minutes Approximately 30 minutes
SP mode EP mode
Make sure you set this function to “ON” before the timer-recording starts.
NOTES:
● If you have programed the VCR to timer-record 2 or more programs, the second
program and those thereafter may not fit on the tape with this function set to "ON". In
this case, do not use this function, but change the tape speed manually during timer
programing.
● In order to ensure that the recording fits on the tape, this function may leave a slight
non-recorded portion at the end of the tape.
● There may be some noise and sound disturbance where the tape speed switches from
SP to EP mode on the tape.
● This function will not work properly on the following tapes: T(ST)-30, T(ST)-60, T(ST)-
90, and T(ST)-120.
m DIGITAL R3 When this function is set to “ON”, edge correction to the luminance signal is
ON performed to enhance details. Normally set this function to “ON”.
OFF
NOTES:
● Depending on the type of tape being used, picture quality may be better with
“DIGITAL R3” set to “OFF”.
● If you use this VCR as the playback VCR for editing, be sure to set “DIGITAL R3” to
“OFF” before starting.
m VIDEO STABILIZER When this function is set to “ON”, you can automatically correct vertical
ON vibrations in the picture when playing back unstable recordings made on
OFF another VCR.
NOTES:
● When you finish viewing a tape, be sure to set this function to “OFF”.
● Regardless of the setting, this function has no effect during recording and during
special effects playback.
● The on-screen display may jitter vertically when this function is set to “ON”.
● To watch recordings with close-caption, set this function to “OFF”.


When this function is set to “ON”;
m 2ND AUDIO RECORD
● If a SAP program is received, the SAP audio is recorded on both the
ON
normal and Hi-Fi tracks. The main audio is not recorded.
OFF
● If a non-SAP program is received, the main audio is recorded on both
the Hi-Fi and normal tracks.
When this function is set to “OFF”, the SAP audio cannot be recorded.
m AUDIO MONITOR This VCR can record two sound tracks simultaneously (normal and Hi-
Fi) on a tape.
HI-FI: Normally select this.
You can select the sound track(s) to listen to while playing back a Hi-Fi
Hi-Fi sound is played
stereo tape.
back.
In addition, when playing back a prerecorded tape containing two
HI-FI L: Sound on the left Hi-Fi
separate audio programs on the Hi-Fi tracks, you can choose either one
channel is played back.
by selecting either “HI-FI L” or “HI-FI R”.
HI-FI R: Sound on the right Hi-Fi
channel is played back.
NORM: Sound on the normal track NOTES:
is played back. ● While playing back a monaural tape, sounds on the normal track will be heard
MIX: Both sounds on the Hi-Fi regardless of this setting.
● If RF connection (Z pg. 7) is used for viewing pictures on the TV, sound will be
track and normal track are
monaural even though you select “HI-FI”.
mixed and played back.
● You can also use the A. MONITOR button on the Remote to select the desired
monitor sound. (Z pg. 17)
m S-VHS MODE You can determine which recording mode — either S-VHS mode or VHS
ON mode — is used for recording on S-VHS tapes.
OFF When this function is set to “ON”, you can record on S-VHS tapes with
S-VHS picture quality.
When this function is set to “OFF”, you can record on S-VHS tapes with
VHS picture quality.
NOTES:
• S-VHS mode allows you to make high quality video recordings with horizontal
resolution of 400 lines, comparing with the 230 lines of resolution of
conventional VHS recordings. To achieve the highest quality picture we
recommended to record in S-VHS mode. (But remember that a conventional
VHS VCR without SQPB cannot play back S-VHS tapes recorded in S-VHS
mode.)
• S-VHS MODE setting does not affect recording on VHS tapes. Recording on
VHS tapes is always performed in VHS mode except when using S-VHS ET
mode (Z pg. 41).
m FRONT AUX INPUT You have to select which terminal — either VIDEO (composite) or S
VIDEO VIDEO (Y/C separate signals) — to use as the video input terminal on the
S-VIDEO front panel.
Make sure to select the correct terminal; otherwise, you may fail in
recording (editing) on this VCR.
m REAR AUX INPUT You have to select which terminal — either VIDEO (composite) or S
VIDEO VIDEO (Y/C separate signals) — to use as the video input terminal on the
S-VIDEO rear panel.
Make sure to select the correct terminal; otherwise, you may fail in
recording (editing) on this VCR.

EN 41
m S-VHS ET This function allows you to record on VHS tapes with S-VHS picture
ON quality. Tapes recorded using this function can be played back on a VCR
OFF equipped with the S-VHS ET function. The S-VHS indicator lights up on
the front display panel when "S-VHS ET" is set to "ON".
NOTES:
● Before recording, make sure that “VIDEO CALIBRATION” is set to “ON”. (Z pg. 37,
38)
● You cannot activate the S-VHS ET function...
– while recording is in progress.
– while timer-recording is in progress.
– while Video Calibration (Z pg. 38) is in progress.
● S-VHS ET does not work with S-VHS tapes.
● To keep the highest quality recording and playback pictures over a long period of
time, S-VHS recording on S-VHS tapes is recommended.
● Use of high grade tapes are recommended for S-VHS ET recordings.
On some tapes, picture quality will not improves even if the S-VHS ET function is
used. Check the recording quality before you start important recordings.
● You can play back S-VHS ET recordings on most of S-VHS VCRs and of VHS VCR
equipped with SQPB (S-VHS QUASI PLAYBACK) function. (Notice some VCRs are
not compatible with this function.)
● While playing back a tape recorded with this function on some tapes, noise may
appear. (If playback picture becomes blurred or interrupted, use a cleaning cassette.)
● During special effect playback (Z pg. 26), noise may appear. If special effect
playback is performed frequently on a tape recorded with this function, the tape may
be damaged and picture may be deteriorated.
Returning point for Playback, Repeat Play or Series Playback can be set
m RETURN POINT to tape end or recording end. (This VCR considers 1-second unrecorded
TAPE END: Playback stops at the portion as the recording end.) When the returning point is reached,
end of tape. playback stops and the cassette will be automatically rewound.
REC END: Playback stops at the
end of the recording. NOTE:
The setting you have made is kept in memory. Even if the VCR is unplugged or the
power failure occurs, it will resume every time you turn on the VCR. (Z pg. 9)
m DAY/TIME INSERT When this function is set to "ON", you can record Month/Day/Year and
clock time display (Z pg. 61) with your picture.
ON
OFF NOTES:
● To use this function, be sure to set "ON SCREEN (REC)" to "ON". (Z pg. 37, 38)
● The superimposed operational indicators on the screen will also be recorded.
the power failure occurs, it will resume every time you turn on the VCR.
(Z␣ pg.␣ 9)
● This function is not available during Audio Dubbing or Insert Editing.
Usually, you can only record onto a cassette with its record safety tab
m REC SAFETY
intact. When the this function is set to “OFF”, recording can be done
ON onto a cassette whose record safety tab is removed.
OFF
NOTES:
the power failure occurs, it will resume every time you turn on the VCR.
(Z␣ pg.␣ 9)
● When "REC SAFETY" is set to "OFF", playback does not start automatically when
you insert a cassette with its record safety tab removed. (Z pg. 15)
m DAILY T. RECORD When you set daily timer recording, you can use one cassette repeatedly.
NORM If you select "AUTO REW", the VCR rewinds tape each time after timer
AUTO REW recording and the timer mode is engaged.
If you select "NORM", the VCR turns off after timer recording. Rewinds
the tape or replace it, and engage timer recording standby mode
manually.

Satellite Auto This function allows you to automatically record a

satellite program which is timer-programed on your DBS
receiver.
Recording Preparation: Connect a DBS receiver to the AUDIO/

VIDEO IN or S VIDEO IN (L-1) connectors* on the rear;
otherwise, you cannot use this function.
• You can also connect the cable box if it has a timer.
* To use these connectors, you have to select which one to use
(Z pg. 40).
REC LINK lamp
1 Set timer program on DBS receiver
• For timer programing method, refer to the
manual supplied with the DBS receiver.
REW FF
2 Load a cassette
PLAY
POWER – +
CH– /+
PUSH / TURN

REC LINK A.DUB
24HR QUICK
Make sure the record safety tab is intact.
PROGRAM
SP EP
4 3 Set tape speed

Press SP/EP ( ) to set the recording speed.
4 Engage
mode
Satellite Auto Recording standby
Press REC LINK for more than 2 seconds.

The VCR turns off automatically and the REC
LINK lamp lights (Satellite Auto Recording
1 2 3 standby mode).
2 When signals come into the VCR from the DBS
4 5 6 receiver, the VCR starts recording (the REC LINK
7 8 9 lamp blinks), and stops recording and goes off
when signals stop coming in.
0 4
• To disengage the Satellite Auto Recording
standby mode, press REC LINK. The REC LINK
lamp goes off.
IMPORTANT: Be sure not to turn on the DBS receiver

1
3 before the program starts broadcasting; otherwise, the
VCR will start recording when the DBS receiver is
turned on.
NOTES:
● While the Satellite Auto Recording standby mode or after Satellite Auto Recording is finished, the VCR will not enter the timer
recording standby mode even though “AUTO TIMER” is set to “ON”. (Z pg. 37, 38)
● If you turn off this VCR while Satellite Auto Recording is in progress, recording stops.
● Video Calibration (Z pg. 38) does not work while Satellite Auto Recording is in progress.
● Auto Clock (Z pg. 11) does not work while in the Satellite Auto Recording standby mode.
● The VCR may not record a short portion at the beginning of the program or may record slightly longer than the actual length of the
program when Satellite Auto Recording method is used.
● If you engage the Satellite Auto Recording standby mode while the DBS receiver is turned on, the VCR will not start Satellite Auto
Recording even though the REC LINK lamp blinks. When you turn off and on the DBS receiver once again, the VCR starts
recording.
● If you have connected another component other than a DBS receiver (or cable box) to the AUDIO/VIDEO IN or S VIDEO IN (L-1)
connectors, be sure not to engage the Satellite Auto Recording standby mode; otherwise, the VCR will start recording when the
connected component is turned on.
● Satellite Auto Recording and timer-recording cannot be performed at the same time.
● If the REC LINK lamp does not light but blinks quickly in the Satellite Auto Recording standby mode (even though your DBS
receiver is turned off), Satellite Auto Recording will not work properly.
If this is the case, perform “Express Timer Programing” (Z pg. 32) to timer-record a satellite program.
(Some DBS receivers output signals even if the power is off. Satellite Auto Recording is not possible with those DBS receivers.)

EN 43
Child Lock You can disable the VCR operations.
● You can only use the Remote for this operation.
While the VCR is turned on, press and hold POWER on
the Remote for more than 10 seconds.
The VCR turns off, and “CL” appears on the front display
panel for about 5 seconds, then the clock time appears
again.
POWER
1 2 3 ● The child lock function is now activated and you

2
cannot turn on the VCR by pressing POWER on the
4 5 6
front panel.
7 8 9
0 4
TIMER To release the child lock, press and hold POWER on the
Remote until the VCR turns on.
● Pressing TIMER during timer recording, unplugging the
AC power cord or a power outage also releases the
1 child lock.
NOTES:
● When the child lock function is in use, keep the Remote out
3 of the children’s reach.
● Timer recording programs will be performed even if the child
lock function is activated.
● If any button on the VCR or on the Remote is pressed when
the child lock function is activated, “CL” appears on the front
display panel for about 5 seconds, then the clock time
appears again.

44 EN EDITING
Edit From 3
Camcorder POWER
PLAY
REW
–
FF
CH– /+
PUSH / TURN
REC LINK A.DUB
Connection
PROGRAM
SP EP
This VCR (for recording)

8
REW FF
PLAY
POWER – +
CH– /+
PUSH / TURN
REC LINK A.DUB

PROGRAM
SP EP
To AUDIO/
VIDEO Input
Audio/video
cable 1 2 3
(supplied) 2
4 5 6
To S VIDEO 7 8 9
Input*
0 4
3
S-video cable
(supplied)
3
To Audio/video
output 1
8
To S-video
Camcorder
4–6 3
45
output
(for playback)
45
Various connection for editing tapes
The following three methods can be used for editing tapes.
● VHS to S-VHS editing (VIDEO-VIDEO connection):
Although the picture quality is inherently limited by the
original VHS quality, the edited tape has better picture
quality than those made by VHS-to-VHS editing.
● S-VHS to VHS editing (VIDEO-VIDEO connection):
Since the original source is recorded in S-VHS mode, the
edited tape has better picture quality than those made by
VHS-to-VHS editing.
● S-VHS to S-VHS (S-VIDEO connection): Original picture
quality of S-VHS made can be duplicated with minimal
picture degradation. This is the best editing method you
can use on S-VHS VCRs.

EN 45
You can use a camcorder as the playback VCR and your
VCR as the recording VCR 6 Return to normal screen
Press MENU.
1 Make connections
Connect an audio/video cable between the 7 Start playback
Set the camcorder to its play mode.
camcorder’s audio/video output connectors and
your VCR’s audio/video input connectors. NOTE:
● When using a camcorder with a monaural If the camcorder is equipped with a superimpose/OSD
output, connect the audio output connector on disable feature then set it to “OFF” before starting
the camcorder to the left audio input connector playback.
on this VCR.
8 Start recording
2 Load a cassette
Insert the cassette to be recorded on into this
On the front panel:
Press REC ( ¶ ).
VCR (for recording). On the Remote:
Press REC ( ¶ ) and PLAY ( 3 ) at the same time.
3 Select input mode on this VCR
Select “L-1” — when connecting the camcorder NOTE:
to the audio/video input Be sure to select “AUTO” for “PICTURE CONTROL” (or
connectors on the rear panel. “NORM” when “VIDEO CALIBRATION” is set to “OFF”) after
Select “F-1” — when connecting the camcorder you finish dubbing the tapes (Z pg. 37 and 38).
to the audio/video input
connectors on the front panel.
On the front panel:
On the Remote:
Press the Number key "0 (AUX)" and/or CH +/–.
4 Select video input terminal

Follow the procedure described on pages 37 and
40.
When using S VIDEO terminal, set “FRONT AUX
INPUT” (or “REAR AUX INPUT” if you use the
connectors on the rear) to “S-VIDEO”.
When using VIDEO terminal, set “FRONT AUX
INPUT” (or “REAR AUX INPUT”) to “VIDEO”.
5 Select edit mode

38.

46 EN EDITING (cont.)
Edit To Or 2 Load cassettes

Insert the playback cassette into the playback
VCR and the cassette to be recorded on into the
From Another recording VCR.
VCR 3 Select input mode on recording VCR

Select the correct external input on the other
VCR.
● On this VCR (when using this VCR as the
recording VCR);
Connection Select “L-1” — when connecting the other VCR
Ex. When using this VCR as the playback VCR to the audio/video input connectors on
the rear panel;
This VCR (for playback)
Select “F-1” — when connecting the other VCR
to the audio/video input connectors on
the front panel.
REMOTE
On the front panel:
R
Push the JOG dial, then turn it to the left or

REMOTE
OUT
AUDIO
S
IN OUT L VHF/UHF
right.
V TV OUT
I VIDEO
D
E
O
On the Remote:
To S VIDEO To AUDIO/
OUT VIDEO OUT
S-video cable
(supplied) Audio/video
cable (supplied)
4 Select
VCR
video input terminal on recording
When using this VCR as the recording VCR,

follow the procedure described on pages 37 and
To S-video To Audio/ 40.
Input video Input When using S VIDEO terminal, set “FRONT AUX
INPUT” (or “REAR AUX INPUT” if you use the
connectors on the rear) to “S-VIDEO”.
Another VCR (for recording) 5 Select edit mode

On this VCR, set “PICTURE CONTROL” to
“EDIT” by following the procedure described on
pages 37 and 38.
You can use your VCR as the playback or recording VCR.
● Refer also to the other VCR’s instruction manual for
connection and its operations.
6 Start playback
Press PLAY ( 3 ) on the playback VCR.
NOTE:
1 Make connections
Connect an audio/video cable between the
If the playback VCR is equipped with a superimpose/
OSD disable feature then set it to “OFF” before starting
playback VCR’s audio/video output connectors playback.
and the recording VCR’s audio/video input
connectors.
● When using this VCR as the recording VCR, 7 Start recording
Press REC ( ¶ ) on the recording VCR.
connect this VCR’s audio/video input
connectors to the audio/video output
connectors on the other VCR. NOTE:
If the playback VCR is monaural, connect the Be sure to select “AUTO” for “PICTURE CONTROL” (or
audio output connector on the playback VCR “NORM” when “VIDEO CALIBRATION” is set to “OFF”) after
to the left audio input connector on this VCR. you finish dubbing the tapes (Z pg. 37 and 38).

EN 47
Audio Dubbing 2 Load a cassette and prepare the audio
source
Connection 3 Select input mode

Select “F-1” — when connecting the audio
This VCR (for recording) component to the audio input connectors on
the front panel.
Select “L-1” — when connecting the audio
component to the audio input connectors on
POWER
PLAY
REW
–
FF
+
the rear panel.
CH– /+
PUSH / TURN On the front panel:
REC LINK
DIGITAL TBC/NR
SP EP
VCR
A.DUB
INSERT
24HR QUICK
PROGRAM

On the Remote:
To AUDIO Audio cable Press the Number key "0 (AUX)" and/or CH +/–.
input (not supplied)
4 Locate start point
1 Press PLAY ( 3 ) to start playback.
2 Press PAUSE ( 8 ) when you find the beginning
To Audio output
of the scene for which you want to audio-dub.
CD player 5 Activate editing mode

Press A.DUB on the front panel.
(as the audio source)
● The VCR enters the Audio Dubbing pause mode.
● blinks, and light up on the front
display panel.
● Audio Dubbing is also possible using the audio
input connectors on the rear panel.
6 Start audio dubbing
Start playing the audio source and press PLAY
( 3 ) on this VCR.
● blinks and is displayed on the front
You can replace sounds recorded on the normal track with display panel.
new sounds — for example, your favorite song played back
on the CD player.
● Refer also to the other audio component’s instruction To stop audio dubbing
manual for connection and its operations. Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 )
on the front panel.
● Audio dubbing automatically stops when the counter
Normal track reading becomes "0:00:00", and the VCR starts normal
Before audio playback.
dubbing
Video and
NOTES:
Hi-Fi track ● During Audio Dubbing, the sound recorded on the normal
track is selected as the monitor sound. If you want to listen to
After audio the Hi-Fi or mixed sound (Hi-Fi sound and monaural sound),
dubbing see "Selecting monitor sound — Audio Monitor" (Z pg. 17).
● During Audio Dubbing, the VCR status indications on TV
screen do not apear.
● "DAY/TIME INSERT" (Z pg. 41) is not available during Audio
1 Make connections
Connect an audio cable between the VCR’s audio
Dubbing.
● Audio Dubbing cannot be performed on a tape with its record
input connectors and the audio component’s safety tab removed. If you want to record onto a tape with its
audio output connectors. record safety tab removed, set "REC SAFETY" to "OFF" (Z pg.
● If the audio component is monaural, connect 37, 41).
● When playing back an audio-dubbed tape, select the sound
the AUDIO L (MONO) input connector on the
you want. See "Selecting monitor sound — Audio Monitor"
VCR.
(Z pg. 17).
● Picture may be distorted if you pause Audio Dubbing.

48 EN EDITING (cont.)
Insert Editing Refer also to the other component’s instruction manual

for connection and its operations.
Insert Editing: You can replace a recorded scene with
and AV Dubbing new scene recorded on another tape or with other

material. Both the picture and the sound recorded on the
Hi-Fi sound track are replaced at the same time.
Audio/Video Dubbing: You can perform Audio Dubbing
Connection and Insert Editing at the same time. This means that the
picture and the sounds recorded on the Hi-Fi sound
track and on the normal track are replaced at the same
This VCR (for recording) time.
• For Audio/Video Dubbing, you can edit pictures and
sound using different sources; connect a video source
POWER
PLAY
REW
–
FF
+
to the video input connector, and an audio source to
CH– /+
PUSH / TURN
the audio input connectors.
REC LINK A.DUB
PROGRAM
SP EP
Insert Editing
To AUDIO/ Source tape

VIDEO input
To
S VIDEO Edited tape
input
Audio/video cable Before
(Supplied) editing
S-video
cable
(Supplied) Normal track
After
To S-video To Audio/ editing
output video output
Video and Hi-Fi track
AV Dubbing
Source tape
Another VCR (for playback)
Edited tape
● Insert Editing and AV Dubbing are also possible
using the audio/video connectors on the rear panel. Before
editing
After
editing

EN 49
1 Make connections
Connect an audio/video cable between the VCR’s 7 Locate start point
Use REW ( ) or JOG dial to reverse the tape
audio/video input connectors and the other (See “Special Effect Playback”: Z pg. 26).
component’s audio/video output connectors. When you find the begining of the scene you
want to edit, press PAUSE ( 8 ).
2 Prepare tapes
Load the source tape on the other VCR, and the
8 Activate editing mode
tape to be edited on this VCR. Press INSERT on the front panel.
● Make sure that the recording format (VHS, S-
3 Select input mode
Select “F-1” — when connecting the other
VHS or S-VHS ET) on the VCR is the same as
that of the original recording on the tape.
component to the audio/video input ● During Insert Editing pause mode ( , and
connectors on the front panel. light up on the front display panel.)
Select “L-1” — when connecting the other ● For AV Dubbing, after pressing INSERT, press
component to the audio/video input A.DUB also. During AV Dubbing insert pause
connectors on the rear panel. mode ( and blink, and lights up on
On the front panel: the front display panel.)
On the Remote:
9 Start editing
Press PLAY ( 3 ) on this VCR, and start playback
on the other component at the same time.
4 Select video input terminal

● During Insert Editing mode (
up on the front display panel.)
and light
40. ● During AV Dubbing mode ( and blink

When using S VIDEO terminal, set “FRONT AUX on the front display panel.)
INPUT” (or “REAR AUX INPUT” if you use the ● When the counter reading becomes
connectors on the rear) to “S-VIDEO”. “0:00:00”, editing automatically stops, and the
VCR starts normal playback.
5 Select edit mode

On this VCR, set “PICTURE CONTROL” to
To stop editing any time during recording
Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 )
“EDIT” by following the procedure described on on the front panel.
pages 37 and 38.
6 Locate end point

1 Press PLAY ( 3 ) to start playback.
NOTES:
● Be sure to select “AUTO” for “PICTURE CONTROL” (or
2 Press PAUSE ( 8 ) when you find the end of “NORM” when “VIDEO CALIBRATION” is set to “OFF”) after
the scene for which you want to edit. you finish editing the tapes (Z pg. 37 and 38).
3 Press C. RESET so that the counter reading ● Editing cannot be performed on a tape with its record safety
tab removed. If you want to record onto a tape with its record
becomes “0:00:00”.
safety tab removed, set "REC SAFETY" to "OFF" (Z pg. 37,
NOTE: 41).
You can also use REW ( ) or FF ( ), or JOG dial ● The recording speed (SP/EP) is determined by the previous
to locate the end point (See “Special Effect Playback”: recording to be replaced. If the recording speed changes on
Z pg. 26) . the tape to be edited while editing the tape, the inserted
picture will be distorted where the recording speed changes.
● When you edit a tape, a small portion of the recording
preceding to the editing start point will be erased from the
edited tape.
● "DAY/TIME INSERT" (Z pg. 41) is not available during Insert
Editing.

50 EN MULTI-BRAND REMOTE CONTROL
TV Brand This Remote can control some functions of remote

controllable TVs of the brands listed below. Without
setting, you can control a JVC TV.
Setting 1 Turn on the TV

Turn on the TV using the Power button on the TV
or its Remote.
2 –2 2 Set TV brand code

Follow the example shown below.
1 Press and hold TV.
2 –1 4 POWER 2 Press MBR SET.
TV 3 Press the Number keys to enter your TV’s
brand code by referring to the table below.
TV/VCR 1 2 3 4 Press OK, and release TV.
2
4 5 6 2 –3 The TV should turn off. If it does, try other

operations below. (Z step 3).
Number
7 8 9 ● Once you have set the Remote to operate the
TV, you do not have to set it until you replace
0 4
the batteries from the Remote.
● PANASONIC has two codes. If the TV does not
function with one code, try entering the other.
3 Operate TV
While holding down TV, press one of the
following buttons: POWER, TV/VCR, TV CH +/–,
2 –4 keys.
(TV Muting), TV VOL +/–, and Number
ENTER
● For some brands, you must press ENTER after
3
TV VOL +/– having pressed the Number keys to enter a

channel number.
TV CH +/– NOTES:
● Depending on the type of TV, some or all functions cannot be
operated using this Remote.
● It’s not possible to operate a TV not equipped with a remote
sensor.
(Ex.) To set Remote to RCA 05:

MBR SET
TV A/B ENTER
/OSD
TV BRAND NAME BRAND CODE 0 5 3 OK

Release
JVC 01, 03
HITACHI 10
Hold Press in succession
MAGNAVOX 02 down
MITSUBISHI 03
PANASONIC 04, 11
RCA 05
SHARP 06
SONY 07
SAMSUNG 12
SANYO 13
SEARS 13
TOSHIBA 08
ZENITH 09

EN 51
Cable Box This Remote can control some functions of the cable
boxes of the brands listed below. Some cable box brands
have more than one code. If your cable box does not
Brand Setting function with a specified code, try other codes.
1 Turn on the cable box

Turn on the cable box using the Power button on
the cable box or its Remote.
2 –1 4
POWER
2 –2
2 Enter cable box brand code
CABLE/DBS 1 Press and hold CABLE/DBS.
1 2 3 2 Press MBR SET.
2
4 5 6 2 –3 3 Press the Number keys to enter your cable

box’s brand code by referring to the table
7 8 9 Number
below.
0 4 4 Press OK, and release CABLE/DBS.
The cable box should turn off. If it does, try
other operations below. (Z step 3).
● Once you have set the Remote to operate the
cable box, you do not have to set it until you
1
replace the batteries from the Remote.
3 Operate cable box

While holding down CABLE/DBS, press one of
3 2 –4 the following buttons: POWER, TV CH +/–, and
Number keys.
ENTER
having pressed the Number keys to enter a
channel number.
TV CH +/– ● To change the cable box’s channels, press TV
CH +/– or the Number keys. (The CH +/–
button can be used to change the VCR’s
CABLE BOX BRAND NAME BRAND CODE
channels only.)
ARCHER 01, 05, 17
CABLETENNA 01, 17
CABLEVIEW 15, 16, 17, 21, 25 NOTES:
CITIZEN 15, 16, 17, 21, 25
CURTIS 02 ● Depending on the type of cable box, some or all functions
DIAMOND 01, 17 cannot be operated using this Remote.
EASTERN 19 ● It’s not possible to operate a cable box not equipped with a
GC BRAND 15, 16, 17, 21, 25 remote sensor.
GEMINI 15
GENERAL INSTRUMENTS 01, 04, 06, 11, 12, 15, 28 ● It’s not possible to set the Remote for both your cable box and
HAMLIN 10, 18, 19, 23 a DBS receiver at the same time. You can only set the Remote
JASCO 15 control to operate one of these units at a time.
JERROLD 01, 04, 06, 11, 12, 15, 28
NOVAVISION 02
OAK 07 (Ex.) To set the Remote to RCA 14:
PANASONIC 13, 14 CABLE/ MBR SET
DBS
PULSER 15, 16, 17, 21, 25 A/B ENTER
/OSD
RCA 13, 14 1 4 3 OK
Release
REGAL 10, 18, 19, 23
REGENCY 19
REMBRANDT 01, 16, 17
SAMSUNG 05, 16, 24 Hold Press in succession
SCIENTIFIC ATLANTA 02 down
SIGMA 07
SL MARX 05, 16, 17, 24, 25
SPRUCER 13, 14
STARGATE 05, 15, 16, 17, 21, 24, 25
TELEVIEW 05, 16, 24
TOCOM 01, 04, 16
UNIKA 01, 17
UNIVERSAL 16, 17, 25
VIDEOWAY 03, 09, 22
ZENITH 03, 09, 22

52 EN MULTI-BRAND REMOTE CONTROL (cont.)
DBS Receiver This Remote can control some functions of the DBS
(Direct Broadcast Satellite) receivers of the brands listed
below.
Brand Setting 1 Turn on the DBS receiver

Turn on the DBS receiver using the Power button
on the DBS receiver or its Remote.
2 Enter DBS receiver brand code

1 Press and hold CABLE/DBS.
POWER 2 Press MBR SET.
2 –1 4 2 –2 3 Press the Number keys to enter your DBS
receiver’s brand code by referring to the table
CABLE/DBS 1 2 3
2
below.
4 5 6 2 –3 4 Press OK, and release CABLE/DBS.
The DBS receiver should turn off. If it does, try
7 8 9 Number other operations below (Z step 3).
0 4 ● Once you have set the Remote to operate the
DBS receiver, you do not have to set it until you
replace the batteries from the Remote.
1 3 Operate DBS receiver

While holding down CABLE/DBS, press one of
the following buttons: POWER, TV CH +/–, and
Number keys.
3
2 –4 having pressed the Number keys to enter a
channel number.
ENTER ● To change the DBS receiver’s channels, press
TV CH +/– or the Number keys. (The CH +/–
button can be used to change the VCR’s
TV CH +/– channels only.)
NOTES:
● Depending on the type of DBS receiver, some or all functions
cannot be operated using this Remote.
● It’s not possible to operate a DBS receiver not equipped with
a remote sensor.
● It's not possible to set the Remote for both your DBS receiver
and a cable box at the same time. You can only set the
Remote to operate one of these units at a time.
DBS BRAND NAME BRAND CODE
JVC (DISH Network) 51
(Ex.) To set the Remote to JVC 51:
ECHOSTAR (DISH Network) 51 CABLE/ MBR SET
DBS A/B ENTER
PRIMESTAR 50 /OSD
5 1 3 OK
Release
SONY (DSS) 41
RCA (DSS) 40

down

EN 53
Changing This Remote is capable of transmitting two control
codes; one set to respond to A code control signals and
another set to respond to B code control signals.
Remote Control This Remote control is preset to send A code signals

because your VCR is initially set to respond to A code
signals. You can easily modify your VCR and the Remote
Code to respond to B code control signals.

When using two JVC VCRs, set two VCRs and their
Remotes to different codes, so that you can operate these
VCRs separately.
2
1 Set remote control code for Remote
1 Press and hold A/B.
2 Press the Number key “2”.
PLAY
REW FF
3 Press OK, and release A/B.
POWER
● The Remote now can transmit B code control

– +
CH– /+
PUSH / TURN

REC LINK A.DUB
24HR QUICK
PROGRAM
signals.
SP EP
2 Check remote control code for VCR

Press and hold PLAY ( 3 ) on the VCR for more
than 5␣ seconds while the VCR is turned off. The
code currently set appears on the display panel.
3 Change code for VCR

Press any key on the Remote.
● The VCR now responds to B code control
1 –1, 3 signals.
● To set the Remote and the VCR back to A code
1 2 3
2 control signals, repeat the same procedure as
4 5 6 1 –2 shown above except pressing the Number key
“1” in step 2 of 1.
7 8 9
0 4 To control two VCRs with the same Remote

You can control two JVC VCRs by switching the remote
control code for the Remote between A and B (Z step
1), keeping two VCRs to different control codes.
● Press the Number key “1” for A code control signals
1
and the Number key “2” for B code control signals. (To
change only the remote control code for the Remote,
DO NOT perform steps 2 and 3 .)
3
1 –3 (Ex.) To set Remote to B code:
MBR SET
A/B ENTER
/OSD
2 3 OK
Release

down

54 EN TROUBLESHOOTING
Before requesting service, use this chart and see if you can repair the trouble yourself. Small problems are often easily
corrected, and this can save you from the trouble of sending your VCR off for repair.
POWER
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
1. The power will not come on. ● The AC power cord is disconnected. Connect the AC power cord.
● Child lock is on. Turn off child lock function (Z pg. 43).
2. The clock works, but the VCR’s ● The VCR is in the timer recording Press TIMER to disengage.
power will not come on. standby mode with “AUTO TIMER”
set to “OFF” (Z pg. 37, 38).
● The child lock function is activated. Press and hold POWER on the
Remote for more than 10 seconds to
release the child lock function (Z pg.
43).
3. The Remote will not function. ● The batteries are discharged. Replace batteries.
● Timer is on. Press TIMER button on the Remote.
● Remote control A/B code is wrong. Reset A/B code (Z pg. 53).
TAPE TRANSPORT
1. The cassette gets stuck partway ● The cassette was inserted incorrectly. Make sure the cassette’s window is
during loading, and is ejected. facing up, the rear label side is facing
you and the arrow on the front of the
cassette is pointing towards the VCR.
Then insert the cassette.
PLAYBACK
1. The tape is running but the picture ● If the RF connection (Z pg. 7) is Select channel 3 or 4 on the TV.
will not appear. used to view the picture, the
channel on the TV is set incorrectly.
● If the AV connection (Z pg. 7) is Select the AV mode on the TV.
used to view the picture, the TV
receiver is set to the wrong mode.
2. Breaks are noticeable in Hi-Fi ● Automatic tracking is engaged. Disengage auto tracking and adjust
sound track. the tracking manually (Z pg. 17).
3. The playback picture is blurred or ● The video heads may be dirty. The heads must be cleaned. Use a
interrupted, even though TV dry cleaning cassette –TCL-2UX– or
broadcasts are clear. Or “USE consult your JVC dealer.
CLEANING CASSETTE” appears on
the screen.
4. The Hi-Fi sound cannot be heard. ● Audio Monitor setting is incorrect. Set Audio Monitor to “HI-FI”
(Z pg. 17 or 40).
RECORDING
1. Recording will not start. ● There is no cassette loaded. Insert a cassette.
● "REC SAFETY" is set to "ON" and the Set "REC SAFETY" to "OFF" (Z␣ pg.␣ 37,
loaded cassette has had its record 41).
safety tab removed.
2. TV broadcasts will not be recorded ● The VCR has been set to “L-1” or “F- Select the appropriate channel on the
properly. 1” input mode by mistake. VCR.
3. Tape-to-tape editing will not work. ● The components have been Connect the components correctly
incorrectly connected, or correct (Z pg. 44 – 49) or check “REAR AUX
video connector (S VIDEO or INPUT or “FRONT AUX INPUT”
VIDEO) is not selected. setting (Z␣ pg.␣ 37, 40).
● The power to one or more of the Make sure the power to all units is on.
units has not been turned on.
● The recording VCR’s input mode has Select the appropriate input mode on
been set incorrectly. the recording VCR.

EN 55
TIMER RECORDING
1. Timer recording will not work. ● The clock and/or the timer have Set the clock and/or timer correctly.
been set incorrectly.
● The timer is not engaged. Press TIMER and make sure that ‰
appears on the front display panel.
● The VCR has not been set up properly. Re-perform the set-up procedures.
Make sure you have compensated for
guide channel and VCR or cable box
channel number mismatches
(Z pg. 30).
2. Timer programing will not work. ● Timer recording is in progress. Timer programing cannot be performed
when timer recording is in progress.
Wait until it finishes.
3. ‰ and ] on the front display ● The timer is engaged but there is no Load a cassette with the record safety
panel will not stop blinking. cassette loaded. tab intact. If the tab is removed, set
"REC SAFETY" to "OFF". (Z pg. 37,
41)
● "REC SAFETY" is set to "ON" and the Set "REC SAFETY" to "OFF" (Z pg.
loaded cassette has had its record 37, 41) or replace the cassette with
safety tab removed. one on which the safety tab is intact.
4. ‰ blinks for 10 seconds and the ● TIMER has been pressed when there Check the programed data and set
timer mode is disengaged. are no programs in memory, or the again if necessary, then press TIMER
timer recording program has not again.
been set correctly.
5. The power shuts off and ‰ and ● The tape reaches its end during The program may not have been
] will not stop blinking. timer recording. recorded in its entirety. Next time be
sure you have enough time on the
tape to record the entire broadcast.
6. You moved, and now VCR Plus+ ● The receivable stations in the new Re-perform the Changing VCR Plus+
system does not work properly. area are received on different Setting procedure (Z pg. 30).
channels than those in the previous
area.
7. “PROGRAM FULL” is displayed on ● All 8 programs of the VCR’s timer Wait until a space in memory clears,
the screen. memory are used. or cancel unnecessary program
information (Z pg. 35).
CONTINUED ON NEXT PAGE \

56 EN TROUBLESHOOTING (cont.)
OTHER PROBLEMS
1. When scanning channels, some of ● Those channels have been preset to If you need the skipped channels,
them are skipped over. be skipped. restore them (Z pg. 14).
2. The channel cannot be changed. ● Recording is in progress. Press PAUSE ( 8 ) to pause the
recording, change channels, then
press PLAY ( 3 ) to resume recording.
3. The Remote will not operate your ● The brand codes are set incorrectly. Reset the correct brand codes (Z pg.
TV or cable box or DBS receiver. 50, 51 or 52).
4. Even though Auto or Semiauto ● The clock setting data received from Select a different host channel during
Clock Set has been performed, the the host channel is incorrect. Semiauto Clock Set (Z pg. 11), or
clock is incorrect. perform Manual Clock Set (Z pg. 12).
5. Buttons and controls do not ● Mode Lock is activated. Press and hold OK on the Remote for
function at all. more than 5 seconds to deactivate
Mode Lock.
MOISTURE CONDENSATION
Moisture in the air will condense on the VCR when you move it from a cold place to a warm place, or under
extremely humid conditions—just as water droplets form on the surface of a glass filled with cold liquid. Moisture
condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the
VCR turned on for a few hours to evaporate the moisture before inserting a tape.
ATTENTION
This VCR contains microcomputers. External electronic noise or interference can cause microcomputer to malfunction. If the
VCR does not operate correctly switch its power off and unplug the AC power cord from the AC supply. Wait for a while and
then plug the power cord back in. Eject and check the condition of the cassette. If everything appears normal, you can operate
the VCR as usual.

EN 57
Questions and answers
PLAYBACK RECORDING
Q. What happens if the tape reaches its end during Q. When I pause and then resume a recording, the end
playback or search? of the recording before the pause is overlapped by
A. The VCR automatically rewinds it to the beginning. the new recording. Why does this happen?
............................................
A. This is normal. It reduces distortion at the pause and
Q. Can the VCR indefinitely remain in still mode?
resume points.
A. No. It stops automatically after 5 minutes to protect ............................................
the heads. Q. Can the VCR indefinitely remain in the recording
............................................
pause mode?
Q. During picture search, still picture playback and
A. No. The VCR automatically stops after 5 minutes to
frame-by-frame playback, the picture is
protect the heads.
intermittent. What’s the cause? ............................................
A. Picture loss occurs when these types of playback are Q. What happens if the tape reaches its end during
attempted with a tape recorded in LP mode. Pressing recording?
PLAY ( 3 ) to return to normal playback will restore A. The VCR automatically rewinds it to the beginning.
the picture.
............................................ TIMER RECORDING
Q. When returning from variable-speed picture search
to normal playback, the picture is disturbed. Should Q. REC and ‰ remain lit on the front display panel. Is
there a problem?
I be concerned about this?
A. No. This is a normal condition for a timer recording
A. No, it is normal.
............................................ in progress.
............................................
Q. When playing back programs that have been timer-
Q. Can I program the timer while I’m watching a tape
recorded consecutively (such one program from
or a TV broadcast?
8:00 to 9:00 and another one from 9:00 to 10:00),
A. Yes, but while you are setting the timer you will not
the picture and sound become momentarily
see the tape’s or broadcast program’s picture as it is
distorted where the first program ends and the
second program begins. Is this a malfunction? replaced by the on-screen menu. (The sound from
the tape or broadcast program will be heard during
A. No. This is normal.
............................................ the timer setting.)
Q. Other than preventing further recording, what
effect does removing the safety tab have?
A. It disables marking of index codes.
............................................
Q. Sometimes, during index search, the VCR cannot
find the program I want to see. Why not?
A. There may be index codes too close together.
............................................
Q. During playback, on-screen display sometimes
jitters. Why does this happen?
A. If the condition of the tape being played back is not
good, jittering of the video (including on-screen
display) may occur.

58 EN INDEX
List of terms
This guide serves as a quick way to locate frequently used terms and on-screen display names.
A M T
Accidental erasure prevention 20 Manual tracking 17 Tape speed 19, 42
AUDIO MONITOR 40 Mode lock 15, 16, 20, 21, 23, 25 Time counter 16, 20
Audio Monitor 17 Multi-Brand Remote Time zone selection 11
Auto Daylight Saving Time 11 Setting cable box brand 51 Timer recording
AUTO SP = EP TIMER 39 Setting DBS receiver brand 52 Canceling 35
AUTO TIMER 38 Setting TV brand 50 Changing 35
Automatic tracking 17 Checking 35
N Express 32
B Next Function Memory 17 Guide channel setting 30
Basic connections VCR Plus+ 28
AV connection 6 O Timer warning display 34
RF connection 6 ON SCREEN (PLAY) 39 Tracking 17
S-video connection 6 ON SCREEN (REC) 38 Troubleshooting 54
On-screen display 21 Tuner setting
C Adding channels 14
Channel No. indication 20 P Auto Channel Set 13
Clock setting 10 PBS channel 8 Deleting channels 14
Manual setting 12 PICTURE CONTROL 38 Manual Channel Set 14
Preparation 10 Playback 15
Semiauto setting 11 Playback Resume Function 18 V
Clock time 16, 20 Plug & Play 8 VCR Plus+ timer programing 28
Contents 5 VIDEO CALIBRATION 38
Counter reset 16, 20 R VIDEO STABILIZER 39
REAR AUX INPUT 40
D REC SAFETY 41 24H quick programing 34
DAILY T. RECORD 41 Recording 19 2ND AUDIO RECORD 39
DAY/TIME INSERT 41 Recording Resume Function 21
DIGITAL R3 39 Repeat Play 16
Digital TBC/NR 18 Repeat Recording 20
RETURN POINT 41
E
Editing S
From a camcorder 44 S-VHS ET 41
From another VCR 46 S-VHS MODE 40
To another VCR 46 Satellite Auto Recording 42
Express timer programing 32 Series Playback 22
Series Recording 24
F Special effect playback
FRONT AUX INPUT 40 Frame-by-Frame Playback 27
Function Set screen 37 High-Speed Picture Search 26
How to use the JOG dial 26
G How to use the SHUTTLE PLUS
Guide channel 30 buttons 27
Picture Search 26
H Skip Search 27
Host channel 8 Slow Motion Playback 27
Still Picture Playback 27
I Variable-Speed Picture Search 26
Index Search 17 Specifications 63
Instant Review 18
L
Last-Function Memory 9

EN 59
Front panel
1 2 3 4
REW FF
PLAY
POWER – +
CH – /+
PUSH / TURN
REC LINK A.DUB

PROGRAM
SP EP
5 6 7 8 9 0 ! @# $ % ^
1 POWER button : Z pg. 15, 19 9 Front display panel : Z pg. 60

2 Cassette loading slot 0 Remote sensor
3 PLAY ( # ) button : Z pg. 15 ! INSERT button : Z pg. 49
4 Advanced JOG dial : Z pg. 15, 19, 26 @ A.DUB button : Z pg. 47
5 S VIDEO input connector : Z pg. 44, 48 # 24HR QUICK PROGRAM button : Z pg. 34
6 AUDIO/VIDEO input connectors : Z pg. 47, 48 $ REC ( ¶ ) button : Z pg. 19, 20
7 DIGITAL TBC/NR button and lamp: Z pg. 18 % PAUSE ( 8 ) button : Z pg. 19, 27
8 REC LINK button and lamp : Z pg. 42 ^ STOP/EJECT ( 7 / 0 ) button : Z pg. 15, 19

60 EN INDEX (cont.)
Front display panel
1 2 34 5
SP
VCR
6 7 8 9
1 Symbolic Mode Indicators 2 Tape speed indicators

STILL: 3 Program start time and stop time indicator :
PLAY: SLOW: Z␣ pg.␣ 34
FF/REW VARIABLE RECORD: Mode Lock indicators : Z pg. 15, 16, 20, 21,
SHUTTLE SEARCH: 23, 25
RECORD PAUSE:
4 Timer mode indicator : Z pg. 29, 33
AUDIO DUBBING: 5 Tape remaining time indicator : Z pg. 16, 20
AUDIO DUBBING PAUSE:
6 S-VHS indicator : Z pg. 15, 41
7 VCR mode indicator : Z pg. 19, 20
INSERT: 8 Cassette mark
9 Channel and auxiliary input (“L-1” and “F-1”)
INSERT PAUSE:
Counter reading : Z pg. 16, 20
AUDIO DUBBING INSERT: Clock time : Z pg. 16, 20
AUDIO DUBBING INSERT PAUSE:

EN 61
Rear panel
1 2 3 4
REMOTE
REMOTE
R
OUT
AUDIO
S
IN OUT L VHF/UHF
V TV OUT
I VIDEO
D
E
O
5 6 7 890
1 AC power cord : Z pg. 6 5 Lithium battery compartment: Z pg. 7

2REMOTE OUT terminal : 6 S VIDEO IN connector : Z pg. 48
Z pg. 22, 24 7 S VIDEO OUT connector : Z pg. 6
3 REMOTE IN terminal : Z pg. 22, 24 8 AUDIO/VIDEO IN connectors : Z pg. 48
*For the Remote Control Unit RM-G30 9 AUDIO/VIDEO OUT connectors : Z pg. 46
(not supplied). 0 TV OUT terminal : Z pg. 6
4 ANTENNA IN terminal : Z pg. 6
On-screen display
7
1
CH 125 RECORD
2 FRI 12:00:00 AM PAUSE
8
3 11/30/01 – WARNING– SP 9
4 STEREO TIMER RECORDING
SAP TO START SOON 0
5 (CANCEL)
B-----+-----+-----+-----E !
INDEX 1 @
6 NORM REMAIN 10:00 #
HI–FI COUNT –1:23:45 $
1 Channel and auxiliary input (“L-1” and “F-1”) 8 VCR operation mode indication
2 Day and clock time 9 Tape speed indication
3 Month/Day/Year 0 Cassette indication
4 STEREO program indication : Z pg. 21 ! Tape position indicator : Z pg. 16
5 SAP (Second Audio Program) indication : @ Index no. indication : Z pg. 17
Z pg. 21 # Tape remaining time : Z pg. 16, 20
6 Audio monitor indications : Z pg. 17, 40 $ Time counter : Z pg. 16, 20
7 Timer warning display : Z pg. 34

62 EN INDEX (cont.)
Remote 1 CABLE/DBS button : Z pg. 51, 52

2 TV button: Z pg. 50
1 & 3 TV/VCR button : Z pg. 19, 21, 50
2 CABLE/ MBR SET * 4 REVIEW button : Z pg. 18
DBS
5 Number buttons : Z pg. 19, 28, 31
TV A/B
POWER
3 (
6 DBS button (No function)
)
TV/VCR A. MONITOR DISPLAY
4 7 CANCEL button : Z pg. 29, 35

1 2 3 q C. (Counter) RESET button : Z pg. 16, 20
5 2
w 8 STOP +/– button : Z pg. 29, 32
4 5 6
6 DBS DAILY WEEKLY
e 9 START +/– button : Z pg. 32
7 8 9 0 PROG. (Program) button : Z pg. 28, 32
7 C. RESET AUX r ! PROG. CHECK button : Z pg. 35
0
t
CANCEL TIMER 4
8 @ REW ( 1 ) button : Z pg. 15, 19, 26
y # REC ( ¶ ) button : Z pg. 19, 20
9 START STOP DATE CH
$ STOP ( 7 ) button : Z pg. 15, 16

u % MENU button : Z pg. 37
0
EXPRESS PROGRAMMING
1 PROG PROG
CHECK
SP/EP SKIP SEARCH
i ^ SHUTTLE PLUS %fi buttons

! TV CH +/– buttons : Z pg. 50, 51, 52
o
PLAY
REW FF
@ & MBR SET button : Z pg. 50, 51, 52

#
REC
STOP PAUS
E p A/B button : Z pg. 53
ENTER
/OSD
Q * POWER button : Z pg. 17, 19
$ MENU TV CH +
3 OK
( A. (Audio) MONITOR button : Z pg. 17

% SHUTTLE
W (TV Muting) button : Z pg. 50
PLUS ) DISPLAY button : Z pg. 16, 20
^
TV
+
VO
q DAILY button : Z pg. 29, 33

L
E
O
– V
TV
TV CH –
w WEEKLY button : Z pg. 29, 33

e AUX button : Z pg. 45, 46, 47, 49
MULTI BRAND
r TIMER button : Z pg. 29, 33, 35
t DATE +/– button : Z pg. 32
REMOTE CONTROL UNIT
y CH +/– button : Z pg. 19, 32

u SKIP SEARCH button : Z pg. 27
i SP/EP button : Z pg. 19, 29, 33
o PLAY ( 3 ) button: Z pg. 15, 19
p FF ( ¡ ) button: Z pg. 15, 19, 26
The glow-in-the-dark buttons shown in white on the Q PAUSE ( 8 ) button: Z pg. 19, 27
illustration above are helpful when using the W OK button
Remote in darkened rooms. ENTER button : Z pg. 50, 51, 52
OSD button : Z pg. 21
Buttons with a small dot on the left side of the name
E SHUTTLE PLUS 4 ¢ (@ #) button
can also be used to operate your TV while holding
: Z pg. 27
down TV on the Remote. (Z pg. 50).
TV VOL +/– button : Z pg. 50
How to use the Remote

Before use, insert two AA size batteries into the Remote with the polarity (ª and ·) matched correctly as
indicated on the battery compartment or on the lid.
The Remote can operate most of your VCR’s functions, as well as basic functions of TV sets, cable boxes and DBS
receivers.
● Point the Remote toward the remote sensor on the target component.
● The maximum operating distance of the remote control is about 8 m.
NOTE:
If the Remote does not work properly, remove its batteries, wait for a few seconds, replace the batteries and then try again.

SPECIFICATIONS EN 63
GENERAL TIMER
Power requirement : AC 120 V` , 60 Hz Clock reference : Quartz
Power consumption Program capacity : 1-year programmable timer/
Power on : 20 W 8 programs
Power off : 2.5 W Memory backup time : Approx. 6 months
Temperature Estimated figure based on
Operating : 5°C to 40°C (41°F to 104°F) supplied fresh battery; actual
Storage : –20°C to 60°C (–4°F to140°F) performance may differ.
Operating position : Horizontal only
Dimensions (W x H x D) : 400 mm x 94 mm x 283 mm
Weight : 3.4 kg ACCESSORIES
Format : S-VHS/VHS NTSC standard Provided accessories : Infrared remote control unit,
Maximum recording time “AA” battery x 2,
SP : 210 min. with ST-210 video Lithium battery CR2025,
cassette S-video cable (4-pin),
EP : 630 min. with ST-210 video RF cable (F-type),
cassette Audio/video cable,
BNC/RCA adapter x 2
VIDEO/AUDIO
Signal system : NTSC-type color signal and Specifications shown are for SP mode unless specified
EIA monochrome signal, otherwise.
525␣ lines/60␣ fields E. & O.E. Design and specifications subject to change without
Recording/ notice.
Playback system : DA-4 (Double Azimuth) head
helical scan system Usable cassettes
Signal-to-noise ratio : 45 dB Full-Size VHS
Horizontal resolution T-30 (ST-30**)
VHS : 230 lines T-60 (ST-60**)
S-VHS : 400 lines T-90
Frequency range T-120 (ST-120**)
Normal audio : 70 Hz to 10,000 Hz T-160 (ST-160**)
Hi-Fi audio : 20 Hz to 20,000 Hz ST-210**
Input/Output : RCA connectors Compact VHS*
(IN x 2, OUT x 1) TC-20 (ST-C20**)
S-video connectors TC-30 (ST-C30**)
(IN x 2, OUT x 1) TC-40 (ST-C40**)
TUNER * Compact VHS camcorder recordings can be

played on this video recorder. Simply place the
Tuning system : Frequency-synthesized tuner
recorded cassette into a VHS Cassette Adapter
Channel coverage
and it can be used just like any full-sized VHS
VHF : Channels 2–13
cassette.
UHF : Channels 14–69
** This VCR can record on regular VHS and Super
CATV : 113 Channels
VHS cassettes. While only VHS signals can be
RF output : Channel 3 or 4 (switchable;
recorded on regular VHS cassettes 1), both VHS
preset to Channel 3 when
and Super VHS signals can be recorded and
shipped) 75 ohms,
played back using Super VHS cassettes.
unbalanced
1)
By using the S-VHS ET function, it is possible to record and
play back with S-VHS picture quality on VHS cassettes on
this VCR.

SR-V10U
VICTOR COMPANY OF JAPAN, LIMITED
Printed in Malaysia
U
COPYRIGHT © 2001 VICTOR COMPANY OF JAPAN, LTD. * *
1001 MNV ID PJ

NTSC Video Recorder SR-V10U

Uploaded by

Copyright:

Available Formats

NTSC Video Recorder SR-V10U

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

NTSC Video Recorder SR-V10U

Uploaded by

Copyright:

Available Formats

VIDEO CASSETTE RECORDER

CABLE/ MBR SET

TV/VCR A. MONITOR DISPLAY

START STOP DATE CH

1 PROG PROG SP/EP SKIP SEARCH

For Customer Use:

INSTRUCTIONS Enter below the Model No. and

Downloaded from www.Manualslib.com manuals search engine

CAUTIONS Caution on Replaceable lithium battery

VCR Plus+ and PlusCode are registered trademarks of Gemstar

Downloaded from www.Manualslib.com manuals search engine

4. Power Cord Protection ANTENNA

NEC – NATIONAL ELECTRICAL CODE

Downloaded from www.Manualslib.com manuals search engine

3. Water and Moisture 3. Replacement Parts

BEFORE YOU INSTALL YOUR NEW

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

What to do if Plug & Play setting failed

Downloaded from www.Manualslib.com manuals search engine

1 Access Main Menu screen

1 3 Select clock set

Downloaded from www.Manualslib.com manuals search engine

8 Return to normal screen

* Auto Daylight Saving Time

Downloaded from www.Manualslib.com manuals search engine

● Holding SHUTTLE PLUS %fi changes the date

4–7 8 Start clock

To make corrections any time during the process

Setting clock manually

● Holding SHUTTLE PLUS %fi changes the time

Downloaded from www.Manualslib.com manuals search engine

1 Access Main Menu screen

2 Access Tuner Set screen

You can automatically TUNER SET

highlight bar (arrow) to

23 SET”, then press OK or

23 PRESS (MENU) TO END

4 Return to normal screen

Downloaded from www.Manualslib.com manuals search engine

2 Access Tuner Set screen

2–4 SHUTTLE PLUS # to

5 Return to normal screen

Setting channels manually

1 Access Main Menu screen

Downloaded from www.Manualslib.com manuals search engine

Playback 1 Load a cassette

REC LINK A.DUB

● The S-VHS indicator lights up on the front

display panel when you play back a tape

Downloaded from www.Manualslib.com manuals search engine

Basic ● To display the VCR status including the tape remaining

Features remaining time is only an estimate.

To reset the time counter, press C. RESET on the

Checking tape position

F While playing back a tape, press and hold PLAY ( 3 )