Structural Design Report

Of
OFFICE BUILDING FOR
RAINAS MUNICIPALITY BUILDING
Tinpiple, Lamjung, Nepal.

Figure 1 Block A

Figure 2 Block B

June 2019.
Structure Design Report
Table of Contents
1.0 Structural Design ................................................................................................................................ 1
1.1 Introduction ........................................................................................................................................ 1
1.2 Features (Block A) ............................................................................................................................. 3
1.3 Features (Block B) ............................................................................................................................. 3
1.4 Loads .................................................................................................................................................. 4
1.4.1 Dead load ........................................................................................................................................... 4
1.4.2 Live load............................................................................................................................................. 4
1.4.3 Seismic Load(Block A) ...................................................................................................................... 4
1.4.4 Seismic Load(Block B) ...................................................................................................................... 5
1.4.5 Load Combinations, NBC 105 ........................................................................................................... 6
1.4.6 Earthquake resistant features: ............................................................................................................ 6
1.5 Codes .................................................................................................................................................. 6
1.5.1 Materials:............................................................................................................................................ 6
1.5.2 Loadings: ............................................................................................................................................ 6
1.5.3 Design Codes: .................................................................................................................................... 6
1.6 Etabs Model and Plan......................................................................................................................... 7
1.7 Story Drifts :- ..................................................................................................................................... 8

2.0 Annex 1 (Loads in Building)

3.0 Annex 2 (Stress Diagram)
4.0 Annex 3 (Column & Foundation Summary)
5.0 Annex 4 (Sample Calculation)

Structural Design Report of Office Building Page ii

1.0 Structural Design
1.1 Introduction
Structural design aims to design a safe structure against expected loads to come in the life period of the
structure due to the dead weights of the structural components, occupancies, wind, earthquakes, snow,
settlements etc. This phase consists of mainly two stages, first is the Analysis, and next is the Design and
detailing of the structure and structural elements to achieve the safest, economically viable at par with the
latest Indian Standard codes. The work will be comprised of following components:
a) Review of the Architectural drawing
b) Structural Analysis and design and detailing with standard commercial Finite element based
software. The Structural analysis shall include linear- static analysis.
Nepal lies in seismically the most active zone. So there is always the risk of large earthquakes. However the
Earthquake Resistant Design doesn’t mean to design a damage-free structure against earthquake shaking, but
has the following basis:
o Minor Earthquakes: No damage at all
o As Moderate Earthquakes: Non-structural elements may get damaged, but Structural Elements are not yet
affected.
o Major Earthquakes: Structural Elements may also be damaged, but collapse is prevented, thereby, saving
the lives and properties.
Thus the structure is so designed as to prevent sudden collapse and remain serviceable against the design
shaking as per codal requirements. This is achieved by performing the proper analysis for seismic loads, and
proper design, maintaining the ductility in the structure.
The Earthquake resistant design is done for the structure performing the Seismic-Coefficient method of
analysis. Following assumptions have been made:
o Earthquake cause impulsive ground motion which is complex and irregular in character, changing in period
and amplitude each lasting for small duration.
o Earthquake is not likely to occur simultaneously with wind.
Structure design and analysis has been performed using ETABS 16.2.1 and STAAD Pro Software. We have
found these tools as user-friendly & reliable. In spite of their efficiency and reliability, we don’t hesitate to
accept and realize that there is always space for improvements.

Structural Design Report of Residential Building Page 1

Structure Design Report

Figure 3 Ground Floor Plan (Block A & B)

Structural Design Report of Office Building Page 2

Structure Design Report
1.2 Features (Block A)
Type of Structure: RCC frame
Analysis: 3D-SMRF
Concrete grade: M20 for all RCC Members.
Steel grade: Fe-500
Design codes: NBC
Base Area: 150.16 Sq.m (Total Area: 342.42 Sq.m)
Number of Floors: Three Story
Height of Storey: 3.3m and 2.1m
Total Height of the Building: 12m
Base Dimension of the Building: 8.2m × 18.1m
Height-Width Ratio: 1.46
Length-Width Ratio: 2.21
Wall and Partition: Brick wall (230mm thick, 110mm thick)
Foundation Type: Isolated and Combined Footing
Columns: Square (400 x 400) mm
Beams: Rectangular (230 x 400, 230 x 350, 150 x 400) mm
Slab: Two-way slab (125mm Thick), 150mm Cantilever Slab
Staircase 175mm Thick Waist slab
Maximum beam span: 4.5m
Modulus of Elasticity of concrete: M20=5000*√fck =22360 N/mm2
Soil Type: Hard soil
Allowable bearing capacity considered: 215 KN/m2 (At 2m Depth)

1.3 Features (Block B)

Type of Structure: RCC frame
Analysis: 3D-SMRF
Concrete grade: M20 for all RCC Members.
Steel grade: Fe-500
Design codes: NBC
Base Area: 192.26 Sq.m (Total Area: 342.42 Sq.m)
Number of Floors: Three Story
Height of Storey: 3.3m and 2.1m
Total Height of the Building: 12m
Base Dimension of the Building: 21.7m × 8.8m
Height-Width Ratio: 1.36
Length-Width Ratio: 2.47

Structural Design Report of Office Building Page 3

Structure Design Report
Wall and Partition: Brick wall (230mm thick, 110mm thick)
Foundation Type: Isolated and Combined Footing
Columns: Square (400 x 400) mm
Beams: Rectangular (230 x 400, 230 x 350, 150 x 400) mm
Slab: Two-way slab (125mm Thick), 150mm Cantilever Slab
Staircase 175mm Thick Waist slab
Maximum beam span: 4.5m
Modulus of Elasticity of concrete: M20=5000*√fck =22360 N/mm2
Soil Type: Hard Soil
Allowable bearing capacity considered: 215 KN/m2 (At 2m Depth)

1.4 Loads

1.4.1 Dead load

a. Self-weight of members
b. Flooring Load = 1.35 KN/m2 and 1.5 KN/m2
c. Wall Load 9” thick without opening = 13.5 KN/m
d. Wall Load 9” thick with opening = 10.5 KN/m
e. Wall Load 5” thick without opening = 8.0 KN/m
f. Wall Load 5” thick with opening = 7.0 KN/m
g. Parapet wall load =4.0 KN/m
h. Partition Load is assigned as per calculation.

1.4.2 Live load

a. Rooms = 2.5 KN/m2
b. Corridor, Staircase = 4.0 KN/m2
c. Balcony = 4.0 KN/m2
d. Roof = 1.5 KN/m2 and 0.75 KN/m2

1.4.3 Seismic Load(Block A)

Fundamental Period = 0.39sec, 0.39 sec X & Y
Basic Seismic coefficient = 0.08
Importance Factor = 1.5
Structural Performance Factor = 1.0
Zone Factor = 1
Seismic Coefficient = 0.12
Seismic weight = 5787.28 KN
Base Shear = 694.47 KN

Structural Design Report of Office Building Page 4

Structure Design Report

1.4.4 Seismic Load(Block B)

Fundamental Period = 0.39sec, 0.39 sec X & Y
Basic Seismic coefficient = 0.08
Importance Factor = 1.5
Structural Performance Factor = 1.0
Zone Factor = 1
Seismic Coefficient = 0.12
Seismic weight = 6079.489 KN
Base Shear = 729.54 KN

Structural Design Report of Office Building Page 5

Structure Design Report
1.4.5 Load Combinations, NBC 105
a. 1.5(DL+IL)
b. DL+1.3IL±1.25EL
c. 0.9DL±1.25EL
d. DL+1.3SL±1.25EL

Where DL= Dead load

IL= Imposed (Live load)
EL= Earthquake load (Along X and Y- direction)
SL= Snow load =0 (no snowfall)

1.4.6 Earthquake resistant features:

Structural System: SMRF
Load path: Continuous
Redundancy: Adequate
Short Columns: Effect considered
Importance Factor I: 1.0 for general building

1.5 Codes

1.5.1 Materials:
1. NBC 101
2. Brick: (IS 1077, IS 2212)
3. Cement: ( IS 8112, IS 12269)
4. Admixtures: (ASTM C 494/C,494/M, IS9103)
5. Reinforcing Steel: (IS 432, IS 1139, IS 1786)

1.5.2 Loadings:
1. Dead Loads: (NBC 102, IS 875 part I)
2. Live loads: (NBC 103, IS 875 part II)
3. Wind loads: (NBC 104)
4. Seismic loads: (NBC 105)

1.5.3 Design Codes:

1. Reinforced concrete: (NBC 110, IS 456, SP 16)
2. Ductile detailing: (IS 13920, SP34)

Structural Design Report of Office Building Page 6

Structure Design Report
1.6 Etabs Model and Plan.

Fig: 3D ETAB Model of Block A

Fig: 3D ETAB Model of Block B.

Structural Design Report of Office Building Page 7

Structure Design Report

Fig: Typical Floor Plan of Block A and B.

1.7 Story Drifts: -

TABLE: Story Drifts (Block A)

Load X Y Z Permissible
Story Direction Drift Label Remarks
Case/Combo m m m Drift
Story4 EQx 1 X 0.000627 17 3.9 0 12 0.004 O.K.
Story4 EQx 2 X 0.000585 17 3.9 0 12 0.004 O.K.
Story4 EQx 3 X 0.000669 17 3.9 0 12 0.004 O.K.
Story4 EQy 1 Y 0.000327 14 3.9 4.5 12 0.004 O.K.
Story4 EQy 2 X 0.000064 17 3.9 0 12 0.004 O.K.
Story4 EQy 2 Y 0.000327 14 3.9 4.5 12 0.004 O.K.
Story4 EQy 3 Y 0.000327 14 3.9 4.5 12 0.004 O.K.
Story3 EQx 1 X 0.001633 16 0 0 9.9 0.004 O.K.
Story3 EQx 2 X 0.001511 16 0 0 9.9 0.004 O.K.
Story3 EQx 3 X 0.001755 18 7.8 0 9.9 0.004 O.K.
Story3 EQy 1 Y 0.000944 15 7.8 4.5 9.9 0.004 O.K.
Story3 EQy 2 Y 0.000984 15 7.8 4.5 9.9 0.004 O.K.
Story3 EQy 3 Y 0.000904 15 7.8 4.5 9.9 0.004 O.K.
Story2 EQx 1 X 0.002189 18 7.8 0 6.6 0.004 O.K.
Story2 EQx 2 X 0.001959 18 7.8 0 6.6 0.004 O.K.
Story2 EQx 3 X 0.00242 18 7.8 0 6.6 0.004 O.K.
Story2 EQy 1 Y 0.001524 18 7.8 0 6.6 0.004 O.K.
Story2 EQy 2 Y 0.001584 18 7.8 0 6.6 0.004 O.K.
Story2 EQy 3 Y 0.001464 18 7.8 0 6.6 0.004 O.K.
Story1 EQx 1 X 0.001669 17 3.9 0 3.3 0.004 O.K.

Structural Design Report of Office Building Page 8

Structure Design Report
Story1 EQx 2 X 0.001459 17 3.9 0 3.3 0.004 O.K.
Story1 EQx 3 X 0.001879 17 3.9 0 3.3 0.004 O.K.
Story1 EQy 1 Y 0.001347 15 7.8 4.5 3.3 0.004 O.K.
Story1 EQy 2 Y 0.001399 15 7.8 4.5 3.3 0.004 O.K.
Story1 EQy 3 Y 0.001305 16 0 0 3.3 0.004 O.K.

TABLE: Story Drifts (Block B)

Load X Y Z Permissible
Story Direction Drift Label Remarks
Case/Combo m m m Drift
Story4 EQx 1 X 0.000574 5 17.4 8.4 14.6 0.004 O.K.
Story4 EQx 2 X 0.000574 5 17.4 8.4 14.6 0.004 O.K.
Story4 EQx 3 X 0.000574 5 17.4 8.4 14.6 0.004 O.K.
Story4 EQy 1 X 0.001124 10 13.5 4.2 14.6 0.004 O.K.
Story4 EQy 1 Y 0.000516 5 17.4 8.4 14.6 0.004 O.K.
Story4 EQy 2 X 0.001124 10 13.5 4.2 14.6 0.004 O.K.
Story4 EQy 2 Y 0.000516 5 17.4 8.4 14.6 0.004 O.K.
Story4 EQy 3 X 0.001124 10 13.5 4.2 14.6 0.004 O.K.
Story4 EQy 3 Y 0.000516 5 17.4 8.4 14.6 0.004 O.K.
Story3 EQx 1 X 0.001384 3 9 8.4 12.5 0.004 O.K.
Story3 EQx 2 X 0.001384 3 9 8.4 12.5 0.004 O.K.
Story3 EQx 3 X 0.001384 3 9 8.4 12.5 0.004 O.K.
Story3 EQy 1 Y 0.001633 24 22.25 8.4 12.5 0.004 O.K.
Story3 EQy 2 Y 0.001633 24 22.25 8.4 12.5 0.004 O.K.
Story3 EQy 3 Y 0.001633 24 22.25 8.4 12.5 0.004 O.K.
Story2 EQx 1 X 0.001825 18 21.3 0 9.2 0.004 O.K.
Story2 EQx 2 X 0.001825 18 21.3 0 9.2 0.004 O.K.
Story2 EQx 3 X 0.001825 18 21.3 0 9.2 0.004 O.K.
Story2 EQy 1 Y 0.002711 18 21.3 0 9.2 0.004 O.K.
Story2 EQy 2 Y 0.002711 18 21.3 0 9.2 0.004 O.K.
Story2 EQy 3 Y 0.002711 18 21.3 0 9.2 0.004 O.K.
Story1 EQx 1 X 0.002715 16 13.5 0 6.1 0.004 O.K.
Story1 EQx 2 X 0.002715 16 13.5 0 6.1 0.004 O.K.
Story1 EQx 3 X 0.002715 16 13.5 0 6.1 0.004 O.K.
Story1 EQy 1 Y 0.003754 12 21.3 4.2 6.1 0.004 O.K.
Story1 EQy 2 Y 0.003754 12 21.3 4.2 6.1 0.004 O.K.
Story1 EQy 3 Y 0.003754 12 21.3 4.2 6.1 0.004 O.K.
Story Plinth EQx 1 X 0.001998 7 0 4.2 2.8 0.004 O.K.
Story Plinth EQx 2 X 0.001998 7 0 4.2 2.8 0.004 O.K.
Story Plinth EQx 3 X 0.001998 7 0 4.2 2.8 0.004 O.K.
Story Plinth EQy 1 Y 0.002726 18 21.3 0 2.8 0.004 O.K.
Story Plinth EQy 2 Y 0.002726 18 21.3 0 2.8 0.004 O.K.
Story Plinth EQy 3 Y 0.002726 18 21.3 0 2.8 0.004 O.K.
Story LT EQx 1 X 0.000879 10 13.5 4.2 1.4 0.004 O.K.
Story LT EQx 2 X 0.000879 10 13.5 4.2 1.4 0.004 O.K.
Story LT EQx 3 X 0.000879 10 13.5 4.2 1.4 0.004 O.K.

Structural Design Report of Office Building Page 9

Structure Design Report
Story LT EQy 1 Y 0.001182 12 21.3 4.2 1.4 0.004 O.K.
Story LT EQy 2 Y 0.001182 12 21.3 4.2 1.4 0.004 O.K.
Story LT EQy 3 Y 0.001182 12 21.3 4.2 1.4 0.004 O.K.

SAMPLE ANALYSIS AND DESIGN OF GRID F-F OF BLOCK A as per

grid naming of ETABS MODEL

2.0 Annex 1 (Loads in Building)

3.0 Annex 2 (Stress Diagram)

4.0 Annex 3 (Column & Foundation Summary)

5.0 Annex 4 (Sample Calculation)

Structural Design Report of Office Building Page 10

Annex 1 (Loads in Building)
ETABS 2016 16.2.1 4/22/2019

4
4
8
4

10.5 8
8
24
10.5 4
13.75
10.5 5
4 24
10.5 4
13.75
10.5
13.5 10.5
8 8
4
Z
6 10.5
10.5 4
7
13.5 5
10.5 4
X Y 5

4
4
13.5 4
54 4

10.5
10.5 4
8
3 8
8 4 4
10.5 4
4 8
2 8
8 4
13.5
10.5 1

8
8
10.5
10.5
D

8
13.5
E
F

Block A.EDB 3-D View Frame Span Loads (Wall)

ETABS 2016 16.2.1 4/22/2019

1.5
1.5
1.5

1.5

1.5
6
1.5
Z 1.5
6
1.5
1.5

X Y 5
1.5
2
4

2
3

5
2

1
5
D
E
F

Block A.EDB 3-D View Uniform Loads Gravity (Wall)

ETABS 2016 16.2.1 4/22/2019

2.5

2.5
2.5
2.5

Z
6
2.5

X Y 5
2.5
2.5
4

2.5
2.5
3

2
2 .5 2

1
2

2
D
E
F

Block A.EDB 3-D View Uniform Loads Gravity (Live<3)

ETABS 2016 16.2.1 4/22/2019

0.75
0.75
0.75
0.75 0.75 0.75
0.75
0.75 0.75
0.75
0.75 0.75
0.75
0.75

0.75 0.75
0.75

1.5

1.5
1.5
1.5
5
1.
1 .5
1Z.5 1.5
5
6
1.

1.5 1.5
X Y 5

5
1.
4

1.5
3

5
1. 2

1
D
E
F

Block A.EDB 3-D View Uniform Loads Gravity (Live Roof)

ETABS 2016 16.2.1 4/22/2019

1.5
1.5
1.5
1.5 1.35 1.5
1.35
1. 5 1.35
1.35 1.5 1.35
1.35
1.35

1.35 1.35
1.35
1.35

1.35
1.35
5
1.35 1.3
1.35

1.35
1.35 5
5 1.3
1.35 1.35 1.3
1.35
1.35
1.35 5 1.
35
1.35 1 .3
Z5
1.3 1.3
5
1.3
5
5
6
5 1.3
5
1 .3
1.3 5
5 1.3
1.3 5
11..335
X 5
Y 5
1.3
5
1.3 5
1. 3
5
4
315.3
535 1.
1.3
5
1.31. 35
1.

35
3

1.
35.35
1.3
5
1. 1 2

35
1
1.

35
1.
D
E
F

Block A.EDB 3-D View Uniform Loads Gravity (Floor Finishing)

ETABS 2016 16.2.1 4/22/2019

9.5

19

19

Z
6

5
X Y
4

1
D
E
F

Block A.EDB 3-D View Frame Span Loads (Staircase)

Annex 2 (Stress Diagram)
ETABS 2016 16.2.1 4/22/2019

6 5 4 3 2 1

F F F F F F

Story4
10.2922 -11.4056
-2.7635

4.2324 -4.1891

Story3
2.7069

-33.9212 -30.9143 -27.9422 -65.9429

38.7621 38.0833 61.5137
-59.8668

-58.5688

33.3246 -48.2658
-58.835

33.3199 -49.8

34.8601 Story2
30.005

36.394

30.9824

-47.8488 -49.9559 -56.2333 -45.0264 -52.5695 -52.6188

-112.9734
-81.4036

-66.1122

-69.7865

-80.9694

52.7175 54.239 60.3892 50.7178 55.2102 44.7979 Story1

49.971
46.9078

49.0079

55.8431
71.6468

123.9168 -126.4047 113.5784 -113.5895 106.9972 -104.1427 102.7474 -100.8313 104.907 -97.9036 101.8079 -99.8425
Base
Y

Block A.EDB Elevation View - F Moment 3-3 Diagram (ENVELOPE) [kN-m]

ETABS 2016 16.2.1 4/22/2019

6 5 4 3 2 1

F F F F F F

Story4
1.9887

3.1576

6.3946

Story3
-2.3759

-3.1828

-5.967

-19.4611 -18.1541 -14.1054 -29.1186

19.8247 19.9102 21.2633 39.5972
46.6493

64.8752

66.2532

44.4224

44.5379
Story2
-46.2493

-62.2312

-67.9751

-49.4535

-45.0972

-29.2447 -24.0508 -19.5346 -15.5622 -21.879 -19.4036

34.678 35.9293 40.2147 33.0153 37.1654 33.592
155.3412

65.9566

88.4431
59.6601

64.111

Story1
-72.3998

-63.0804

-61.0016

-88.7176
-150.9288

-51.4616 -47.2156 -43.9324 -43.5174 -41.1746 -42.6116

Z 54.7385 51.9068 50.7502 48.9227 50.6908 47.0807

Base
Y

Block A.EDB Elevation View - F Shear Force 2-2 Diagram (ENVELOPE) [kN]
ETABS 2016 16.2.1 4/22/2019

6 5 4 3 2 1

F F F F F F

Story4

Story3
-32.5717 7.1539

-147.8914 -161.1159 -147.1828 -165.2062 Story2

-12.5789 13.9579

-234.7242 -337.1371 -404.5171 -384.8821 -139.3704 -130.5273 Story1

-460.0847 -635.7894 -580.1579 -551.3314 -419.344 -334.7226 Base

Y

Block A.EDB Elevation View - F Axial Force Diagram (ENVELOPE) [kN]

ETABS 2016 16.2.1 4/22/2019

6 5 4 3 2 1

F F F F F F

Story4
0.6245
0.1901

0.1188

Story3
-0.0983

-0.0653

-0.757

-2.6909 -2.5576 -2.5576 -2.5576

2.1943 2.1091 2.1091 2.1091
-2.1285 1.7244

2.2101

-1.6752 1.6671

-1.1872 1.1084
-0.219 0.161

Story2
-2.1243

-2.8163 -3.2215 -3.2215 -3.2215 -3.2215 -3.2215

2.4109 2.6939 2.6939 2.6939 2.6939 2.6939
3.6633

3.2688

3.3875

2.1039
-0.2022 0.197

Story1
-1.8405
-3.4156

-3.2784
-4.2365

-2.308 -2.0444 -2.0444 -2.0444 -2.0444 -2.0444

Z 2.0171 1.8275 1.8275 1.8275 1.8275 1.8275

Base
Y

Block A.EDB Elevation View - F Torsion Diagram (ENVELOPE) [kN-m]

Annex 3 (Column & Foundation
Summary)
ETABS 2016 16.2.1 4/22/2019

1 1 1

D E F

Story4

Story3

323 197 360 376 197 339 Story2

220 197 197 197 197 209
1280

1280

1280

197 291 649 743 211 581 659 197 673 197 197 197
Story1
197 162 324 371 225 314 330 285 337 56 197 197
1428

1531

1403

Base
X

Block A.EDB Elevation View - 1 Longitudinal Reinforcing (IS 456:2000)

ETABS 2016 16.2.1 4/22/2019

2 2 2

D E F

Story4

Story3

358 197 330 355 197 343 Story2

217 197 197 197 197 225
1280

1317

1327

197 197 320 734 197 676 716 197 689 197 197 197
Story1
197 80 160 367 297 338 358 363 344 54 197 197
1392

1437

1436

Base
X

Block A.EDB Elevation View - 2 Longitudinal Reinforcing (IS 456:2000)

ETABS 2016 16.2.1 4/22/2019

3 3 3

D E F

Story4

197 197 197 197 197 197 Story3

197 197 197 197 197 197
1280

1307

1280
560 197 560 649 197 569 Story2
280 222 280 325 282 284
1280

1280

1280

626 197 562 633 197 585 Story1

351 247 316 317 221 378
1363

1432

1397

Base
X

Block A.EDB Elevation View - 3 Longitudinal Reinforcing (IS 456:2000)

ETABS 2016 16.2.1 4/22/2019

4 4 4

D E F

Story4

7 19
19 7
7 19
7 19 7 19
19 1280 7
7 19
7 19 7 19
19 7
7 19
19 7
Story3
1280

1280

1280
580 197 531 627 197 558 Story2
290 243 265 313 321 279
1280

1302

1280

702 197 640 699 197 656 Story1

374 278 329 349 250 408
1383

1451

1405

Base
X

Block A.EDB Elevation View - 4 Longitudinal Reinforcing (IS 456:2000)

ETABS 2016 16.2.1 4/22/2019

5 5 5

D E F

Story4

7 19
19 7
7 19
7 19 7 19
19 1280 7
7 19
6 19 7 19
21 7
7 19
19 7
Story3
1280

1280

1280
197 197 375 715 197 589 611 197 537 Story2
197 94 188 358 262 295 305 285 366
1280

1361

1280

197 223 599 872 218 726 747 197 691 Story1
197 150 300 436 284 392 373 264 508
1434

1750

1428

Base
X

Block A.EDB Elevation View - 5 Longitudinal Reinforcing (IS 456:2000)

ETABS 2016 16.2.1 4/22/2019

6 6 6

D E F

Story4

7 19
19 7
7 19
7 19 7 19
19 1280 7
7 19
2 19 7 22
24 5
7 19
19 7
Story3
1280

1280

1280
197 197 351 716 197 529 523 197 522 Story2
197 197 176 432 212 422 321 272 476
1280

1956

1280

197 205 572 876 319 705 731 199 689 Story1
197 197 286 527 288 605 429 347 587
2084

2299

2092

Base
X

Block A.EDB Elevation View - 6 Longitudinal Reinforcing (IS 456:2000)

ETABS 2016 16.2.1 6/26/2019

7 7 7 7 7 7

A B C D E F

Story4
7 19
19 7
7 19 19
7 19 7

1280
19 7
7 19 29
19
7 19 7 5
7 19
197 197 230 19 7
Story3
197 197 197
1280

1288

1280

1280
363 197 391 389 197 439 558 197 611 560 197 428 446 197 532 Story2
197 197 197 197 197 219 279 283 305 280 197 214 223 197 266
1280

1280

1280

1280

1280

1280

736 197 751 713 197 646 706 197 677 632 197 611 675 197 743 Story1
417 286 376 357 237 345 353 248 338 411 197 423 412 258 465
1280

1280

1280

1280

1280

1280

416 148 389 399 148 384 386 148 391 432 160 425 426 181 463 Story Plinth
351 148 358 339 148 352 345 148 339 394 172 398 413 181 402
1280

1280

1280

1280

1280

1330

241 148 250 243 148 242 238 148 244 267 148 263 270 148 265 Story LT
Z
214 148 196 202 148 201 203 148 197 233 148 236 229 148 247
1373

1337

1332

1507

1629

2097

Base
X

Block B rev.EDB Elevation View - 7 Longitudinal Reinforcing (IS 456:2000)

ETABS 2016 16.2.1 6/26/2019

8 8 8 8 8 8

A B C D E F

0 0 0 Story4
0 0 0

Story3
1280

1296
376 197 395 390 197 443 510 197 465 388 197 382 415 197 477 Story2
197 197 198 197 197 222 255 294 233 197 197 197 208 212 250
1280

1280

1280

1410

1572

1391

759 200 801 741 197 718 779 199 795 717 197 675 704 197 704 Story1
387 346 400 371 303 359 389 404 398 364 212 380 371 246 465
1280

1280

1280

1325

1426

1438

426 148 393 403 148 388 396 148 396 429 164 439 433 183 466 Story Plinth
354 148 366 342 148 356 349 148 346 406 178 396 416 182 409
1280

1280

1280

1280

1329

1372

244 148 253 246 148 246 241 148 246 269 148 268 275 148 266 Story LT
Z
217 148 198 205 148 203 205 148 199 237 148 238 230 148 251
1329

1280

1280

1412

1667

1885

Base
X

Block B rev.EDB Elevation View - 8 Longitudinal Reinforcing (IS 456:2000)

ETABS 2016 16.2.1 6/26/2019

9 9 9 9 9 9

A B C D E F

Story4

197 197 197 197 197 197 197 197 197 Story3
197 197 197 197 197 197 197 197 197
1280

1280

1280

1280
363 197 390 389 197 426 523 197 554 503 197 494 517 197 500 Story2
197 197 197 197 197 213 262 253 277 251 197 247 259 197 263
1280

1280

1280

1280

1280

1280

751 197 763 726 197 674 700 197 700 671 197 651 676 197 699 Story1
405 300 382 363 239 337 350 246 350 379 197 386 391 248 481
1280

1280

1280

1280

1280

1280

418 148 390 400 148 385 390 148 391 429 163 436 430 178 458 Story Plinth
352 148 360 339 148 353 346 148 343 403 176 395 410 179 407
1280

1280

1280

1280

1280

1287

242 148 251 244 148 243 240 148 244 266 148 264 273 148 264 Story LT
Z
215 148 197 203 148 202 203 148 198 235 148 236 228 148 250
1373

1334

1319

1428

1722

1965

Base
X

Block B rev.EDB Elevation View - 9 Longitudinal Reinforcing (IS 456:2000)

ETABS 2016 16.2.1 4/22/2019

D E F
129 129 129

129 129 129

129 129 129

129 129 129

208 197 197

104 197 197

197 291 649 743 211 581 659 197 673 197 197 197

1 197 162 324 371

173
225 314 330 285 337
173 173 173
56 197 197
43 43
129
129

605
344

644
334

173
173

634
414
129
129
43 173 173
173 173 173
129
129

197
217

197
301

173

197
261
129
129
43
173 173 181
43
173 43
129
129

514
329

601
301

173
173

597
312
129
129
197 197 320 734 197 676 716 197 689 197 197 197

2 197 80 160 367 297 338 358 363 344 54 197 197
515
291

530
265

538
311
197
197

197
197

197
197
459
327

456
286

485
347
626 197 562 633 197 585
3 351 247 316 317 221 378
492
298

482
270

505
329
197
197

197
197

197
197
462
313

453
291

489
331

702 197 640 699 197 656

4 374 278 329 349 250 408
482
300

462
297

479
355
197
197

197
197

197
197
511
307

589
294

648
324

197 223 599 872 218 726 747 197 691

5 197 150 300 436 284 392 373 264 508
129
129

656
328

836
418

872
436
129
139

197
376

209
641

218
595

Y
129
129

663
331

828
414

848
424

197 205 572 876 319 705 731 199 689

6 197 197 286 527
X 288 605 429 347 587

Block A.EDB Plan View - Story1 - Z = 3.3 (m) Longitudinal Reinforcing (IS 456:2000)
ETABS 2016 16.2.1 4/22/2019

D E F

323 197 360 376 197 339

1 220 197 197 197 197 209
320
212

340
197

342
227
197
197

197
197

197
197
258
197

239
197

284
197
358 197 330 355 197 343
2 217 197 197 197 197 225
285
197

250
197

287
197
197
197

197
197

197
197
311
225

324
211

352
226
560 197 560 649 197 569
3 280 222 280 325 282 284
382
211

372
197

173
173

412
218
197
197

197
197

173

197
197
43
361
230

330
197

173
173

430
215

580 197 531 627 197 558

4 290 243 265 313 321 279
399
220

326
197

426
226
197
197

197
197

197
197
423
226

370
197

401
252

197 197 375 715 197 589 611 197 537

5 197 94 188 358 262 295 305 285 366
129
129

602
301

554
277

350
197
172

151
395

197
381

197
197
32

Y
129
129

586
293

538
269

414
207

197 197 351 716 197 529 523 197 522

6 197 197 176 432
X 212 422 321 272 476

Block A.EDB Plan View - Story2 - Z = 6.6 (m) Longitudinal Reinforcing (IS 456:2000)
ETABS 2016 16.2.1 4/22/2019

D E F

197 197 197 197 197 197

3 197 197 197 197 197 197
197
197

197
197
197
197

197
197
197
197

197
197

4
197
197

197
197
197
197

197
197
197
197

197
197

5
197
197

197
197
197
197

197
197

Y
197
197

197
197

6 X

Block A.EDB Plan View - Story3 - Z = 9.9 (m) Longitudinal Reinforcing (IS 456:2000)
ETABS 2016 16.2.1 6/26/2019

A B C D E F
4.5 (m) 4.5 (m) 4.5 (m) 3.9 (m) 3.9 (m)

736 197 751 713 197 646 706 197 677 632 197 611 675 197 743
7 417 286 376 357 237 345 353 248 338 411 197 423 412 258 465

1007

1027
652
326

754
377

788
411

929
514

583

692
4.2 (m)

197
290

199
369

217
354

244
373

255
395

257
398
1022

1001
672
336

796
398

869
435

977
488

511

558
759 200 801 741 197 718 779 199 795 717 197 675 704 197 704
8 387 346 400 371 303 359 389 404 398 364 212 380 371 246 465
655
327

768
384

845
423

959
479

972
486

967
588
4.2 (m)

197
269

197
327

211
348

240
357

243
350

247
373

Y
656
328

747
390

822
419

910
528

951
627

987
714

751 197 763 726 197 674 700 197 700 671 197 651 676 197 699
9 X
405 300 382 363 239 337 350 246 350 379 197 386 391 248 481

Block B rev.EDB Plan View - Story1 - Z = 6.1 (m) Longitudinal Reinforcing (IS 456:2000)
ETABS 2016 16.2.1 6/26/2019

A B C D E F
4.5 (m) 4.5 (m) 4.5 (m) 3.9 (m) 3.9 (m)

363 197 391 389 197 439 558 197 611 560 197 428 446 197 532
7 197 197 197 197 197 219 279 283 305 280 197 214 223 197 266
304
197

360
197

613
307

623
312

546
334

712
399
4.2 (m)

197
197

197
197

197
285

197
254

197
248

197
266
303
197

350
197

662
331

521
260

560
280

713
357
376 197 395 390 197 443 510 197 465 388 197 382 415 197 477
8 197 197 198 197 197 222 255 294 233 197 197 197 208 212 250
301
197

344
197

644
322

513
256

550
276

703
352
4.2 (m)

197
197

197
197

197
284

197
245

197
238

197
259

Y
304
197

361
197

627
314

564
294

598
336

688
389

363 197 390 389 197 426 523 197 554 503 197 494 517 197 500
9 X
197 197 197 197 197 213 262 253 277 251 197 247 259 197 263

Block B rev.EDB Plan View - Story2 - Z = 9.2 (m) Longitudinal Reinforcing (IS 456:2000)
ETABS 2016 16.2.1 6/26/2019

A B C D E F
4.5 (m) 4.5 (m) 4.5 (m) 3.9 (m) 3.9 (m)

197 197 230

7 197 197 197
197
197

197
197
4.2 (m)

197
197

197
197
197
197

197
197
8
197
197

197
197
4.2 (m)

197
197

197
197

Y
197
197

197
197

197 197 197 197 197 197 197 197 197

9 X
197 197 197 197 197 197 197 197 197

Block B rev.EDBPlan View - Story3 - Z = 12.5 (m) Longitudinal Reinforcing (IS 456:2000)
ETABS 2016 16.2.1 4/22/2019

6 5 4 3 2 1

F F F F F F

Story4

0.21% 0.21% 0.21% 0.21% 0.21% 0.21% 0.21% 0.21% 0.21% Story3
0.21% 0.21% 0.21% 0.21% 0.21% 0.21% 0.21% 0.21% 0.21%
0.80%

0.80%

0.80%

0.80%

0.45% 0.21% 0.38% 0.44% 0.21% 0.46% 0.47% 0.21% 0.45% 0.38% 0.21% 0.31% 0.31% 0.21% 0.37% Story2
0.22% 0.21% 0.21% 0.27% 0.21% 0.25% 0.23% 0.21% 0.24% 0.25% 0.21% 0.21% 0.21% 0.21% 0.25%
0.80%

0.80%

0.80%

0.80%

0.83%

0.80%

0.92% 0.24% 0.95% 0.70% 0.21% 0.52% 0.53% 0.21% 0.55% 0.53% 0.21% 0.58% 0.65% 0.21% 0.69% Story1
0.46% 0.65% 0.47% 0.35% 0.21% 0.39% 0.36% 0.21% 0.36% 0.38% 0.21% 0.34% 0.34% 0.28% 0.45%
1.31%

0.89%

0.88%

0.87%

0.90%

0.88%

Base
Y

Block A.EDB Elevation View - F Rebar Percentage (IS 456:2000)

ETABS 2016 16.2.1 4/22/2019

6 5 4 3 2 1

F F F F F F

Story4

254.94 254.94 254.94 254.94 254.94 254.94 254.94 254.94 254.94

Story3
443.37
443.37

443.37
443.37

443.37
443.37

443.37
443.37

254.94 254.94 254.94 415.18 379.11 399.65 459.47 415.74 454.74 290.53 269.01 258.34 256.08 254.94 254.94
Story2
443.37
443.37

443.37
443.37

443.37
443.37

443.37
443.37

443.37
443.37

443.37
443.37

893.09 439.12 913.77 656.64 678.71 561.86 510.68 492.65 504.21 514.82 531.75 535.63 637.41 619.10 607.03
Story1
443.37
443.37

443.37
443.37

443.37
443.37

443.37
443.37

443.37
443.37

443.37
443.37

Base
Y

Block A.EDB Elevation View - F Shear Reinforcing (IS 456:2000)

 Column Summary
Demand Rebar Area: -

Grid Name Column Name Ground Floor 1st Floor 2nd Floor

1D C1 1428 1280
1E C1 1531 1280
1F C1 1403 1280
2D C1 1392 1280
2E C1 1437 1317
2F C1 1436 1327
3D C1 1363 1280 1280
3E C1 1432 1280 1307
3F C1 1397 1280 1280
4D C1 1383 1280 1280
4E C1 1451 1302 1280
4F C1 1405 1280 1280
5D C2 1434 1280 1280
5E C2 1750 1361 1280
5F C2 1428 1280 1280
6D C2 2084 1280 1280
6E C2 2299 1956 1280
6F C2 2092 1280 1280
7A C1 1373 1280
7B C3 1337 1280
7C C3 1332 1280 1280
7D C3 1507 1280 1288
7E C3 1629 1281 1280
7F C3 2097 1280 1280
8A C2 1329 1280
8B C3 1280 1280
8C C3 1280 1280 1280
8D C3 1412 1410
8E C3 1667 1572
8F C3 1885 1391 1296
9A C1 1373 1280
9B C3 1334 1280
9C C2 1319 1280 1280
9D C3 1428 1280 1280
9E C3 1722 1280 1280
9F C2 1965 1280 1280
Provided Design:-

G+1 st Floor 2nd Floor Attic

Column Size (mm)
Bar dia nos Bar dia nos Bar dia nos
16 8 16 4 16 4
C1 400X400
12 4 12 8 12 8
16 8 16 8
C2 400X400 16 12
12 4 12 4
20 8 20 4 20 4
C3 400X400
16 4 16 8 16 8

Note:
1. The reinforcement provided are increased from demand value to increase the moment capacity of column
at joint (should be more than that of beams).
2. Columns of Block B Are Designed Considering Base as fixed at Plinth Level, hence increasing the
provided rebar area.
Footing Summary: -

BC=215 KN/m2 (At 2m Depth of Footing)

Grid P, KN Fx, KN Fy, KN Mx, KNm My, KNm Footing Name

F1 223 -2 -6 7 -1
D1 253 -8 -1 2 -7
E1 277 4 -9 10 6
F2 280 -5 2 -2 -4 F1
D2 281 3 0 1 6
A9 237 1 1 0 1
A7 242 1 -1 0 0
D3 366 6 -1 2 9
F3 368 -3 0 1 -1
E2 362 3 2 -2 5
D4 380 7 0 1 10
F4 387 -4 0 0 -2
E3 399 3 0 1 5 F2
B9 331 0 1 0 0
B7 337 0 -1 0 0
A8 349 1 0 0 0
F9 408 -1 1 0 0
F8 406 -1 0 0 -1
F5 424 -3 -11 12 0
E4 452 3 0 1 6
D5 523 -1 -6 7 2
E5 528 1 -9 11 3
E9 438 0 1 0 0
F3
B8 448 0 0 0 0
D9 477 0 0 0 0
C9 555 0 1 0 0
C7 556 0 -1 0 0
E8 450 0 0 0 0
D8 502 0 0 0 0
F4
C8 609 0 0 0 0
D6 389 -6 8 -8 -3
CF1
D7 420 0 -1 0 0
E6 367 4 15 -15 7
CF1
E7 491 0 -1 0 0
F6 307 -2 17 -18 1
CF1
F7 332 -1 -1 0 -1

Note Sample footing design is attached with this Report.

Annex 4 (Sample Calculation)
ETABS 2016 16.2.1 License #*1C93648XQT8W2GR

ETABS 2016 Concrete Frame Design

IS 456:2000 Column Section Design

Column Element Details Type: Ductile Frame (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF
Story1 C12 12 COLUMN 400X400 UDCon 8 0 3300 0.786

Section Properties

b (mm) h (mm) dc (mm) Cover (Torsion) (mm)

400 400 56 30

Material Properties

E c (MPa) f ck (MPa) Lt.Wt Factor (Unitless) f y (MPa) f ys (MPa)

22360.68 20 1 500 415

Design Code Parameters

ɣC ɣS
1.5 1.15

Axial Force and Biaxial Moment Design For P u , M u2 , M u3

Design P u Design M u2 Design M u3 Minimum M 2 Minimum M 3 Rebar Area Rebar %

kN kN-m kN-m kN-m kN-m mm² %
207.1824 -14.055 -104.1427 4.1436 4.1436 1405 0.88

Axial Force and Biaxial Moment Factors

K Factor Length Initial Moment Additional Moment Minimum Moment

Unitless mm kN-m kN-m kN-m
Major Bend(M3) 0.776177 2900 -53.1811 0 4.1436
Minor Bend(M2) 0.729731 2900 -6.0048 0 4.1436

Shear Design for V u2 , V u3

Shear V u Shear V c Shear V s Shear V p Rebar A sv /s

kN kN kN kN mm²/m
Major, V u2 43.9324 79.4311 55.0394 38.3304 443.37
Minor, V u3 51.8543 79.4311 55.0394 51.8543 443.37

Block A.EDB Page 1 of 2 4/22/2019

ETABS 2016 16.2.1 License #*1C93648XQT8W2GR

Joint Shear Check/Design

Joint Shear Shear Shear Shear Joint Shear

Force V Top V u,Tot Vc Area Ratio
kN kN kN kN cm² Unitless
Major Shear, V u2 N/A N/A N/A N/A N/A N/A
Minor Shear, V u3 N/A N/A N/A N/A N/A N/A

(1.1) Beam/Column Capacity Ratio

Major Ratio Minor Ratio

N/A N/A

Additional Moment Reduction Factor k (IS 39.7.1.1)

Ag A sc P uz Pb Pu k
cm² cm² kN kN kN Unitless
1600 14.1 1966.8899 611.2015 207.1824 1

Additional Moment (IS 39.7.1)

Consider Length Section KL/Depth KL/Depth KL/Depth Ma

Ma Factor Depth (mm) Ratio Limit Exceeded Moment (kN-m)
Major Bending (M 3 ) Yes 0.879 400 5.627 12 No 0
Minor Bending (M 2 ) Yes 0.879 400 5.291 12 No 0

Notes:

N/A: Not Applicable

N/C: Not Calculated

N/N: Not Needed

Block A.EDB Page 2 of 2 4/22/2019

ETABS 2016 16.2.1 License #*1C93648XQT8W2GR

ETABS 2016 Concrete Frame Design

IS 456:2000 Beam Section Design

Beam Element Details Type: Ductile Frame (Summary)

Level Element Unique Name Section ID Combo ID Station Loc Length (mm) LLRF
Story1 B11 56 M BEAM 230X400 UDCon 5 4300 4500 1

Section Properties

b (mm) h (mm) b f (mm) d s (mm) d ct (mm) d cb (mm)

230 400 230 0 35 35

Material Properties

E c (MPa) f ck (MPa) Lt.Wt Factor (Unitless) f y (MPa) f ys (MPa)

22360.68 20 1 500 415

Design Code Parameters

ɣC ɣS
1.5 1.15

Factored Forces and Moments

Factored Factored Factored Factored

M u3 Tu V u2 Pu
kN-m kN-m kN kN
-112.9734 0.0853 137.2883 -12.6483

Design Moments, M u3 & M t

Factored Factored Positive Negative

Moment Mt Moment Moment
kN-m kN-m kN-m kN-m
-112.9734 0.1375 0 -113.1108

Design Moment and Flexural Reinforcement for Moment, M u3 & T u

Design Design -Moment +Moment Minimum Required

-Moment +Moment Rebar Rebar Rebar Rebar
kN-m kN-m mm² mm² mm² mm²
Top (+2 Axis) -113.1108 872 15 872 218
Bottom (-2 Axis) 0 436 15 0 436

Block A.EDB Page 1 of 2 4/22/2019

ETABS 2016 16.2.1 License #*1C93648XQT8W2GR

Shear Force and Reinforcement for Shear, V u2 & T u

Shear V e Shear V c Shear V s Shear V p Rebar A sv /s

kN kN kN kN mm²/m
171.6463 52.6927 119.547 59.967 907.6

Torsion Force and Torsion Reinforcement for Torsion, T u & V U2

Tu Vu Core b 1 Core d 1 Rebar A svt /s

kN-m kN mm mm mm²/m
0.0007 135.3687 180 350 0

Block A.EDB Page 2 of 2 4/22/2019

 125MM THICK SLAB

Geometry Data
Item Value Unit
Length along shorter direction 4.2 m
Length along longer direction 4.5 m
Panel Type Two adjacent edges discontinuous
Criteria for Depth User-Defined Depth
User Defined Depth 125 mm

Material Data
Item Value Unit
Grade of Concrete M20
Grade of Steel Fe500
Unit weight of concrete 2500 kg/m3

Loads
Item Value Unit
Include self-weight? Yes
Superimposed dead load 2.5 kN/m2
Live load 4 kN/m2

Loads Combinations
Load Combination # 1
Factor for Superimposed Dead load and Self Wt(if Considered) 1.5
Factor for Live load 1.5
Factor for Other load 1.5

Reinforcement Data
Item Value Unit
Barsize along shorter dirn.(mm) 8
Barsize along longer dirn.(mm) 8
Clear Cover 20 mm

1
Calculation Sheet Report

Design Data
Clear Length of shorter span of the slab , Lx= 4200.000 mm

Clear Length of longer span of the slab , Ly= 4500.000 mm

Panel Type is Two adjacent Edge Discontinuous

Uniformly Distibuted Live Load , Wl= 0.00400 N/sq. mm

Characteristic Strength of concrete , Fck= 20.000 N/sq. mm

Characteristic Strength of steel , Fy= 500.000 N/sq. mm

Unit Weight Of Concrete, c= 0.0000245 N/cubic mm

Bar size for reinf. in shorter Dir. , x= 8.000 mm

Bar size for reinf. in longer Dir. , y= 8.000 mm

Clr. Cover to the outermost Reinf. Bar of the slab , d' = 20.000 mm

Calculation Of Reinforcement
Overall Depth of the Slab, D = 125.000 mm

Dead Load Of Slab , Wd= D * c= 0.00306 N/sq. mm

Effective Depth Of The Slab , d = D - d' - x/2 = 101.000 mm

Effective Thickness Of the Slab along X-Dir ,dx= d = 101.000 mm

Effective Thickness Of the Slab along Y-Dir ,dy= d - x/2 - y/2 = 93.000 mm

Effective Length of shorter span of the slab , Lex= Lx + d = 4301.000 mm

Effective Length of longer span of the slab , Ley= Ly + dy= 4593.000 mm

Ratio of longer to shorter span , r = Ly/Lx= 1.068

Max. Factored Load among all comb. ,W = 0.01434 N/sq. mm

Moment Co-efficient in shorter dir. at span , x= 0.03839

Moment Co-efficient in shorter dir. at edge ,  'x= 0.05107

Moment Co-efficient in longer dir. at span , y= 0.03500

2
Moment Co-efficient in longer dir. at edge ,  'y= 0.04700

Factored Moment at ,

Span in shorter direction , Mux=  x * W * Lx = 10182.95316 Nmm

2

Span in longer direction , Muy=  y * W * Lx = 9282.65271 Nmm

2

Support in shorter direction , M'ux=  ' x* W * Lx = 13545.63704 Nmm

2

Support in longer direction , M'uy=  ' y* W * Lx = 12465.27649 Nmm

2

Width of the Slab , b = 1 mm

Limiting Moment of resistance of section

Along X-Direction , Mu,lim-x= 27258.31282 Nmm

Along Y-Direction , Mu,lim-y= 23111.18004 Nmm

Area Of steel reinf. in X-Dir. at span bottom , Astx= 0.24686 sq. mm

Area Of steel reinf. in Y-Dir. at span bottom , Asty= 0.24568 sq. mm

Area Of steel reinf. in X-Dir. at support top , A'stx= 0.33631 sq. mm

Area Of steel reinf. in Y-Dir. at support top , A'sty= 0.33902 sq. mm

Minimum Area Of steel reinf. in X-Dir. , Astx-min= 0.15000 sq. mm

Minimum Area Of steel reinf. in Y-Dir. , Asty-min= 0.15000 sq. mm

Cross-sectional Area Of steel in X-Dir. , Ax= * x /4 = 50.26544 sq. mm

2

Cross-sectional Area Of steel in Y-Dir. , Ay= * y /4 = 50.26544 sq. mm

2

Spacing in shorter Dir. at span , Sx= 200.000 mm

Spacing in longer Dir. at span , Sy= 200.000 mm

Maximum Spacing in shorter Dir. , Sx-max= 300.000 mm

Maximum Spacing in longer Dir. , Sy-max= 270.000 mm

Spacing in shorter direction at edge , S'x= 140.000 mm

Spacing in longer direction at edge , S'y= 140.000 mm

Calculation Of Shear
Factored shear force in shorter direction , Vux= 21.46454 N

3
Factored shear force in longer direction , Vuy= 20.55480 N

Shear stress developed at shorter span , cx,dev= Vux/ (b + dx) = 0.21252 MPa

Shear stress developed at longer span , cy,dev= Vuy/ (b + dy) = 0.22102 MPa

Percentage of steel reinf. in shorter dir. at top , P'tx= 0.33298

Permissble shear stress at the section along Y-axis ,cx= 0.40539 MPa

Percentage of steel reinf. in longer dir. at top , P'ty= 0.36454

Permissble shear stress at the section along X-axis ,cy= 0.42090 MPa

Deflection Check at mid Span

PROVIDED DESIGN REQUIRED DESIGN

mm Bars, main
Short Span 4200 dia 8
Long Span 4500 spacing 200
0.201%
Thkness, D 125 Ast required 251.327 mm2
Thkness, d 97
Fy 500
Bars, main f= 217.5
dia 8
dia 8 Modification factor 1.8
spacing 300
L/d basic 26
Ast provided 335.1 mm2 L/d permissible 46.8
% 0.268% L/d Provided 43.3
Required modification
factor 1.66534
OK

4
Staircase Design
Data
Riser 15 mm
Tread 300 mm
span 4500.00 mm
fck 20 MPa
OD of slab
fy 500 MPa mm <=300 275 250 225 200 175 =>150
density of concrete 25 kN/mm2 k 1 1.05 1.1 1.15 1.2 1.25 1.3
Live Load 4 kN/m2
width of slab 1.00 m 19.495 kN/m
Finish load 1.3 kN/m2 14.5125 14.513
waist slab length 1.20 m A B
landing A length 1.65 m landing A waist slab landing B
landing B length 1.65 m 1.65 m 1.2 m 1.65 m
Effective cover = 15 mm
Landing width 1 m 4.5 m

Slab depth tried= 175 mm

D.L. of flight
step section= 0.002 mm2
Inclined slab= 0.090 m2
Total area= 0.092 m2
D.L. of step section, 1m in width and 300 mm in plan length= 2.3091 kN/m
D.L. per m2 on plan= 7.697 kN/m2
F.L.= 1.3 kN/m2
L.L= 4 kN/m2
Total dead load= 12.997 kN/m2
Factored load= 19.495 kN/m2
Total fact load in 1 m wide slab= 19.495 kN/m
Landing A
self weight of slab= 4.375 kN/m2
finish load= 1.3 kN/m2
Live load = 4 kN/m2
Total load= 9.675 kN/m2
factored load= 14.5125 kN/m2
TD.L. of 1m wide slab= 14.51 kN/m
Landing B
self weight of slab= 4.375 kN/m2
finish load= 1.3 kN/m2
Live load = 4 kN/m2
Total load= 9.675 kN/m2
factored load= 14.5125 kN/m2
TD.L. of 1m wide slab= 14.51 kN/m
Stair flight
Total load on stair case= 71.286
Reaction at A = Vu 35.643 kN rough
Maximum moment Mu = 42.565 kNm 80.196 36.735 0.8969
effective depth required= 124.185 mm
Adopted effet.depth d = 160 mm
Overall depth D = 175 mm
Steel design
Mu = 0.87*fy*Ast* d (1 - fy*Ast/fck*b*d)
c b a
611.5610055 -1 0.00016
Ast.= 684.84 5715.16 mm2
Use 12 mm dia. Bars @ 165 mm c/c 6.5 4 inches
Ast provided = 12 @ 101.6 mm c/c ----> 1113.2 mm2
Shear Check
Nom.shear stress τv = 0.22 Mpa
% steel provided= 0.70 %
τc = 0.543 MPa Table 19 IS 456 clause 40.2.1
τ'c = 0.56976 Mpa OK in shear
Distribution Bar design
Astd = 210.00 mm2/m
Try steel bar 10 mm dia. Bars @ 374.00 mm c/c
Provided spacing = 200 mm diameter = 10 mm
Provide steel area= 392.70 mm2/m
Development length check
Ld =0.87*fy*dia./(4*taubd*1.6) 56.6406 *diameter
Ld = 679.6875 mm Bond stress
Mu1 = 69.19 kN M20 M25 M30 M35 M40 and above
Vu 35.64 kN 1.2 1.4 1.5 1.7 1.9
Lo = 0
Ld = 2523.41 mm ok
Deflection check
L/d = αβγδλ
α= 26
β= 1 L< 10m
percentage of steel= 0.70
fs=(0.58*As required/Ast provided)*fy = 178.41 Mpa
γ= 1.3 fig.4, pg 38 IS456
δ= 1
λ= 1
Allowble L/d = 33.8
Actual L/d = 28.13 safe in deflection
 ISOLATED FOOTING - F1
Geometry Data
Item Value Unit
Footing Sizing Option User Defined Sizing
Length of Footing(X-Dirn) 1.7 m
Length of Footing(Y-Dirn) 1.7 m
Thickness at Edge 200 mm
Thickness at Column Face or Pedestal Face 450 mm
Depth of Foundation 1.5 m
Type of Column Rectangular
Col. Dia. 0.3 m
Col. Length( X-dirn) 400 mm
Col. Width (Y-dirn) 400 mm
Allowable Gross Bearing Capacity of Soil 215 kN/m2

Modification Factors for Serviceabilty check

Load Combination Combination 1
Bearing Capacity Factor 1
FOS Overturning 1.5
FOS Sliding 1.5
Contact Area Percentage 100

Primary Load Cases

Loads Load Case 1 Unit
Vertical Load 281 kN
Horiz. Load Along X-dirn 3 kN
Horiz. Load Along Y-dirn 0 kN
Moment Along X-dirn 1 kNm
Moment Along Y-dirn 6 kNm

Load Combination Factors for Strength Design

Load Combination Combination 1
Selfweightfactor 1.5
Primary Load 1 1.5

Materials Data
Item Value Unit
Unit Wt. of Soil 18 kN/m3
Unit Weight of Water 1000 kg/m3

1
 Grade of Concrete M20
Grade of Steel Fe 500
Unit Wt. of Concrete. 2500 kg/m3

Reinforcement Data
Item Value Unit
Dia of bar at bot.along X (mm) 12
Dia of bar at bot.along Y (mm) 12
Dia of bar at top along X (mm) 12
Dia of bar at top along Y (mm) 12
Consider Clause 34.4 of IS-456-2000 Yes
Percentage of Reinforcement in Column 1.39
Shear Consideration for Foundation Slab Increase depth of footing
Clear Cover for Foundation Slab 0.06 m
Clear Cover for Pedestal 0.04 m

Calculation Sheet Report

Footing Size Calculations
Foundation Dimension in X-Direction(L x ) = 1.700 m
Foundation Dimension in Y-Direction(L y ) = 1.700 m

Stability Calculation of Foundation against Serviceability Criteria

Weight of Foundation(Wfdn) = 20.196 kN
Weight of Backfill(Wbkfl) = 59.955 kN
Vertical load on Column in Load Case 1 (P) = 281.000 kN
Load on foundation due to surcharge in Load Case 1 (P) = 0.000 kN
Total Vertical load in Load Case 1 (P) = 361.151 kN
Total Moment in X-direction in Load Case 1 ( Mx) = 2.350 kNm
Total Moment in Y-direction in Load Case 1 ( My) = 6.000 kNm
Maximum Bearing Pressure developed in Load Case 1 ( Prmax) = 135.163 kN/sq.m
Minimum Bearing Pressure developed in Load Case 1 ( Prmin) = 114.768 kN/sq.m
Allowable Gross Bearing Pressure in Load Case 1 ( Q All ) = 215.000 kN/sq.m
Total Restoring Moment about Y-axis in Load Case 1 = 306.978 kN-m
Total Overturning Moment about Y-axis in Load Case 1 = 2.350 kN-m
FOS against overturning about Y-axis in Load Case 1 (FOS ovrX ) = 130.629

2
Total Restoring Moment about X-axis in Load Case 1 = 306.978 kN-m
Total Overturning Moment about X-axis in Load Case 1 = 6.000 kN-m
FOS against overturning about X-axis in Load Case 1 (FOS ovrY ) = 51.163
Allowable FOS against overturing in Load Case 1( Fos over-turn) = 1.500
FOS ovrX in Load Case 1 > Fosover-turn in Load Case 1 Hence OK.
FOS ovrY in Load Case 1 > Fosover-turn in Load Case 1 Hence OK.
Total Sliding Force Along X-Direction in Load Case 1 = 3000.000 kN
Total Resisting Force against sliding in Load Case 1 = 180575.333 kN
FOS against sliding along X-axis in Load Case 1 (FOS slidingX ) = 60.192
Allowable FOS against sliding in Load Case 1 (FOS sliding ) = 1.500
FOS slidingX in Load Case 1 > Fossliding in Load Case 1 Hence OK.
Contact Area in Load Case 1 (A contact ) = 2.890 sq. m
Percentage of Contact Area in Load Case 1 (A percentage contact ) = 100.000
Allowable percentage of contact area in Load Case 1(A contPerc ) = 100.000
Tension does not occur
Hence,the foundation is safe against all serviceability criteria
Transfer of Load at the Base of Column as per clause 34.4 of IS:456-2000
Maximum Actual Bearing Stress on the Loaded Area = 2412.500 kN/sq.m
Supporting Area for Bearing of Footing ( A 1 )= 2.890 m2
Loaded area at the column base ( A 2 )= 0.160 m2
Permissible Bearing Stress = 0.45*Fck*sqrt(A1/ A2) = 18000.000 kN/sq.m

Calculation of Bottom Reinforcement of the footing

Design soil pressure under the foundation.
Pressure on Foundation in Load Case 1 (PrDesign) = 161.144 kN/sq.m
Maximum upward soil pressure under the foundation(PrDesign ) = 161.144 kN/sq.m
Moment along X-direction on foundation at critcal section on right side of Column( Mx designRt ) = Prdesign*
(((Lx- BCriticalx) / 2)- Ex) 2 /2 = 0.034 kNm per mm length
Moment along X-direction on foundation at critcal section on left side of Column( Mx designLt ) = Prdesign*
(((Lx- BCriticalx) / 2)+ Ex) 2 /2 = 0.034 kNm per mm length
Moment along Y-direction on foundation at critcal section on right side of Column( My designRt ) = Prdesign*
(((Ly- BCriticaly) / 2)- Ey) 2 /2 = 0.034 kNm per mm length

3
Moment along Y-direction on foundation at critcal section on left side of Column( My designLt ) = Prdesign*
(((Ly- BCriticaly) / 2)+ Ey) 2 /2 = 0.034 kNm per mm length
Characteristic strength of concrete (f ck ) = 20.000 N/sq.mm
Yeild strength of reinforcing steel (f y ) = 500.000 N/sq.mm
Limiting MU/BD 2 of the footing section = 2.672 N/sq.mm
Calculated MU/BD 2 in X direction at bottom (Right of Column) = 0.231 N/sq.mm
Calculated MU/BD 2 in X direction at bottom (Left of Column) = 0.231 N/sq.mm
Calculated MU/BD 2 in Y direction at bottom (Right of Column) = 0.246 N/sq.mm
Calculated MU/BD 2 in Y direction at bottom (Left of Column) = 0.246 N/sq.mm
Calculated MU/BD 2 in X direction at bottom (Right of Column) < Limiting MU/BD 2 Hence OK.
Calculated MU/BD 2 in X direction at bottom (Left of Column) < Limiting MU/BD 2 Hence OK.
Calculated MU/BD 2 in Y direction at bottom (Right of Column) < Limiting MU/BD 2 Hence OK.
Calculated MU/BD 2 in Y direction at bottom (Left of Column) < Limiting MU/BD 2 Hence OK.
Required Reinforcement along X-direction at Bottom on right side of Column( Ast bxRight ) = 460.80 mm 2
/m length
Required Reinforcement along X-direction at Bottom on left side of Column( Ast bxLeft ) = 460.80 mm 2 /m
length
Required Reinforcement along Y-direction at Bottom on right side of Column( Ast byRight ) = 446.40 mm 2
/m length
Required Reinforcement along Y-direction at Bottom on left side of Column( Ast byLeft ) = 446.40 mm 2 /m
length
Spacing Provided for Reinforcement along X-direction at Bottom on right side of Column(S bxRightprov ) =
245.00 mm
Spacing Provided for Reinforcement along X-direction at Bottom on left side of Column(S bxLeftprov ) =
245.00 mm
Spacing Provided for Reinforcement along Y-direction at Bottom on right side of Column(S byRightprov ) =
250.00 mm
Spacing Provided for Reinforcement along Y-direction at Bottom on left side of Column(S byLeftprov ) =
250.00 mm
Provided Reinforcement along X-direction at Bottom on right side of Column( Ast bxRightprov ) = 461.62
mm 2 /m length
Provided Reinforcement along X-direction at Bottom on left side of Column( Ast bxLeftprov ) = 461.62 mm 2
/m length

4
Provided Reinforcement along Y-direction at Bottom on right side of Column( Ast byRightprov ) = 452.39
mm 2 /m length
Provided Reinforcement along Y-direction at Bottom on left side of Column( Ast byLeftprov ) = 452.39 mm 2
/m length

One way shear calculation for bottom Reinforcement

Maximum permissible shear stress of concrete ( cmax ) = 2.800 N/sq.mm
Effective thickness of footing at the critical section (parallel to X-axis) of failure against one way shear
(D sfx ) = 236.308 mm
Effective thickness of footing at the critical section (parallel to Y-axis) of failure against one way shear
(D sfy ) = 228.923 mm
Upward shear force on footing at the critical section on right side of column parallel to Y-axis (SF xRight )
= 42.864 kN per m length
Upward shear force on footing at the critical section on left side of column parallel to Y-axis (SF xLeft ) =
42.864 kN per m length
Upward shear force on footing at the critical section on right side of column parallel to X-axis (SF yRight )
= 44.798 kN per m length
Upward shear force on footing at the critical section on left side of column parallel to X-axis (SF yLeft ) =
44.798 kN per m length

Shear stress at the critical section parallel to Y-axis on right side of column( vxRight) = 0.181 N/sq.mm

Shear stress at the critical section parallel to Y-axis on left side of column( vxLeft) = 0.181 N/sq.mm

Shear stress at the critical section parallel to X-axis on right side of column( vyRight) = 0.196 N/sq.mm

Shear stress at the critical section parallel to X-axis on left side of column( vyLeft) = 0.196 N/sq.mm

Permissible shear stress at the section parallel to Y-axis on right side of column( cxRight) = 0.323 N/sq.mm

Permissible shear stress at the section parallel to Y-axis on left side of column( cxLeft) = 0.323 N/sq.mm

Permissible shear stress at the section parallel to X-axis on right side of column( cyRight) = 0.325 N/sq.mm

Permissible shear stress at the section parallel to X-axis on left side of column( cyLeft) = 0.325 N/sq.mm

cxRight > vxRight . Hence OK.

cxLeft > vxLeft . Hence OK.

cyRight > vyRight . Hence OK.

cyLeft > vyLeft . Hence OK.

Punching Shear Calculation

5
Ratio of minimum to maximum dimension of column (c) = 1.000
Value of Ks= 1.000
Minimum thickness of footing at critical section of punching shear (DPunch ) = 300.462 mm
Perimeter of the punching shear zone (PeriPunch ) = 3112.000 mm
Area of the punching shear zone (AreaPunch ) = 605248.000 sq. mm
Shear force for punching (SF punch ) = Prdesign* (Bx* By- AreaPunch) = 368.174 kN

Actual punching shear stress ( vPunch ) = SFpunch/ (PeriPunch* DPunch) = 0.394 N/sq.mm

Allowable punching shear stress ( AllPunch ) = Ks* 0.25 * SQRT(fck) = 1.118 N/sq.mm

AllPunch > vPunch Hence OK.

6
 Job No Sheet No Rev
Company Name 1
Engineer Date

Job Title Checked Date

Approved Date

Client File CF1.etc Dt/Tm 22-Apr-2019 16:26

Calculation

Combined Footing : CF
Calculation of Footing Weight & Soil Weight
Dimension of Footing in X-dirn.(B x )
= 2750.00 mm
Dimension of Footing in Y-dirn.(B y )
= 3500.00 mm
Type of column is Rectangular
Dimension of Left Column in X-dirn.(B cx1 )
= 400.00 mm
Dimension of Left Column in Y-dirn.(B cy1 )
= 400.00 mm
Distance of left column centre from left edge (Lcoll)
= 1400.00 mm
Dimension of Right Column in X-dirn.(B cx2 )
= 400.00 mm
Dimension of Right Column in Y-dirn.(B cy2 )
= 400.00 mm
Distance of right column centre from right edge (Rcolr)
= 1400.00 mm
Total thickness of footing (D)
= 450.00 mm
Area of Foundation (A f )
=Bx xBy = 9625000.00 mm 2
Depth of foundation from top of soil (D f )
= 2000.000 mm
Effect of water table is not considered
Total Weight of soil on footing (W s )
= 254056.07 N
Total Weight of Foundation (W f )
= 105964.95 N
Total Dead load Surcharge on foundation ( W SDL )
= 0.00 N
Total Live load Surcharge on foundation ( W SLL )
= 0.00 N
Calculation of Loads for Stability Checking
Total vertical Load from column
Dead Load case (Pd )
= 858000.00 N
Dead+Live Load case (Pdl )
= 858000.00 N
Dead+Wind or Seismic Load case (Pdws )
= 858000.00 N
Dead+Live+Wind or Seismic Load case (Pdlws )
= 858000.00 N
Dead+Live+Wind or Seismic + Other Load case (Pdlwso )
= 858000.00 N
Dead+Other Load case (Pdo )
= 858000.00 N
Dead+Live+Other Load case (Pdlo )
= 858000.00 N
Total Shear at column bottom along X dirn.

Print Time/Date: 06/26/2019 11:45 STAAD.etc Release 4.5 Page 1 of 8

 Job No Sheet No Rev
Company Name 2
Engineer Date

Job Title Checked Date

Approved Date

Client File CF1.etc Dt/Tm 22-Apr-2019 16:26

Calculation, cont...

Dead Load case (H xd )

= 4000.00 N
Dead+Live Load case (H xdl )
= 4000.00 N
Dead+Wind or Seismic Load case (H xdws )
= 4000.00 N
Dead+Live+Wind or Seismic Load case (H xdlws )
= 4000.00 N
Dead+Live+Wind or Seismic+Other Load case (H xdlwso )
= 4000.00 N
Dead+Other Load case (H xdo )
= 4000.00 N
Dead+Live+Other Load case (H xdlo )
= 4000.00 N
Total Shear at column bottom along Y dirn.
Dead Load case (H yd )
= 14000.00 N
Dead+Live Load case (H ydl )
= 14000.00 N
Dead+Wind or Seismic Load case (H ydws )
= 14000.00 N
Dead+Live+Wind or Seismic Load case (H ydlws )
= 14000.00 N
Dead+Live+Wind or Seismic +Other Load case (H ydlwso )
= 14000.00 N
Dead+Other Load case (H ydo )
= 14000.00 N
Dead+Live+Other Load case (H ydlo )
= 14000.00 N
Total Moment at foundation bottom along X dirn.
Dead Load case (M xd )
= 30200000.00 Nmm
Dead+Live Load case (M xdl )
= 30200000.00 Nmm
Dead+Wind or Seismic Load case (M xdws )
= 30200000.00 Nmm
Dead+Live+Wind or Seismic Load case (M xdlws )
= 30200000.00 Nmm
Dead+Live+Wind or Seismic +Other Load case (M xdlwso )
= 30200000.00 Nmm
Dead+Other Load case (M xdo )
= 30200000.00 Nmm
Dead+Live+Other Load case (M xdlo )
= 30200000.00 Nmm
Total Moment at foundation bottom along Y dirn.
Dead Load case (M yd )
= 13300000.00 Nmm
Dead+Live Load case (M ydl )
= 13300000.00 Nmm
Dead+Wind or Seismic Load case (M ydws )
= 13300000.00 Nmm
Dead+Live+Wind or Seismic Load case (M ydlws )

Print Time/Date: 06/26/2019 11:45 STAAD.etc Release 4.5 Page 2 of 8

 Job No Sheet No Rev
Company Name 3
Engineer Date

Job Title Checked Date

Approved Date

Client File CF1.etc Dt/Tm 22-Apr-2019 16:26

Calculation, cont...

= 13300000.00 Nmm
Dead+Live+Wind or Seismic+Other Load case (M ydlwso )
= 13300000.00 Nmm
Dead+Other Load case (M ydo )
= 13300000.00 Nmm
Dead+Live+Other Load case (M ydlo )
= 13300000.00 Nmm
Stability Calculation in Dead Load case
Total vertical load ( P )
= 1218021.02 N
Total Moment along X dirn. (M xd )
= 30200000.00 Nmm
Total Moment along Y dirn. (M yd )
= 13300000.00 Nmm
FOS against overturning about Y-axis (FOS ovrxd )
= 70.58
FOS against overturning about X-axis (FOS ovryd )
= 125.92
Contact Area ( A contact-d )
= 9625000.00 sq.mm
Tension does not occur.
Pressure on foundation ( Pr d )
= 0.13 N/sq.mm
Stability Calculation in Dead + Live Load case
Total vertical load ( P )
= 1218021.02 N
Total Moment along X dirn. (M xdl )
= 30200000.00 Nmm
Total Moment along Y dirn. (M ydl )
= 13300000.00 Nmm
FOS against overturning about Y-axis (FOS ovrxdl )
= 70.58
FOS against overturning about X-axis (FOS ovrydl )
= 125.92
Contact Area ( A contact-dl )
= 9625000.00 sq.mm
Tension does not occur.
Pressure on foundation ( Pr dl )
= 0.13 N/sq.mm
Stability Calculation in Dead + Wind or Seismic Load case
Total vertical load ( P )
= 1218021.02 N
Total Moment along X dirn. (M xdws )
= 30200000.00 Nmm
Total Moment along Y dirn. (M ydws )
= 13300000.00 Nmm
FOS against overturning about Y-axis (FOS ovrxdws )
= 70.58
FOS against overturning about X-axis (FOS ovrydws )
= 125.92
Contact Area ( A contact-dws )
= 9625000.00 sq.mm

Print Time/Date: 06/26/2019 11:45 STAAD.etc Release 4.5 Page 3 of 8

 Job No Sheet No Rev
Company Name 4
Engineer Date

Job Title Checked Date

Approved Date

Client File CF1.etc Dt/Tm 22-Apr-2019 16:26

Calculation, cont...

Tension does not occur.

Pressure on foundation ( Pr dws )
= 0.13 N/sq.mm
Stability Calculation in Dead + Live + Wind or Seismic Load case
Total vertical load ( P )
= 1218021.02 N
Total Moment along X dirn. (M xdlws )
= 30200000.00 Nmm
Total Moment along Y dirn. (M ydlws )
= 13300000.00 Nmm
FOS against overturning about Y-axis (FOS ovrxdlws )
= 70.58
FOS against overturning about X-axis (FOS ovrydlws )
= 125.92
Contact Area ( A contact-dlws )
= 9625000.00 sq.mm
Tension does not occur.
Pressure on foundation ( Pr dlws )
= 0.13 N/sq.mm
Stability Calculation in Dead + Live + Wind or Seismic + Other Load case
Total vertical load ( P )
= 1218021.02 N
Total Moment along X dirn. (M xdlwso )
= 30200000.00 Nmm
Total Moment along Y dirn. (M ydlwso )
= 13300000.00 Nmm
FOS against overturning about Y-axis (FOS ovrxdlwso )
= 70.58
FOS against overturning about X-axis (FOS ovrydlwso )
= 125.92
Contact Area ( A contact-dlwso )
= 9625000.00 sq.mm
Tension does not occur.
Pressure on foundation ( Pr dlwso )
= 0.13 N/sq.mm
Stability Calculation in Dead + Other Load case
Total vertical load ( P )
= 1218021.02 N
Total Moment along X dirn. (M xdo )
= 30200000.00 Nmm
Total Moment along Y dirn. (M ydo )
= 13300000.00 Nmm
FOS against overturning about Y-axis (FOS ovrxdo )
= 70.58
FOS against overturning about X-axis (FOS ovrydo )
= 125.92
Contact Area ( A contact-do )
= 9625000.00 sq.mm
Tension does not occur.
Pressure on foundation ( Pr do )
= 0.13 N/sq.mm

Print Time/Date: 06/26/2019 11:45 STAAD.etc Release 4.5 Page 4 of 8

 Job No Sheet No Rev
Company Name 5
Engineer Date

Job Title Checked Date

Approved Date

Client File CF1.etc Dt/Tm 22-Apr-2019 16:26

Calculation, cont...

Stability Calculation in Dead + Live + Other Load case

Total vertical load ( P )
= 1218021.02 N
Total Moment along X dirn. (M xdlo )
= 30200000.00 Nmm
Total Moment along Y dirn. (M ydlo )
= 13300000.00 Nmm
FOS against overturning about Y-axis (FOS ovrxdlo )
= 70.58
FOS against overturning about X-axis (FOS ovrydlo )
= 125.92
Contact Area ( A contact-dlo )
= 9625000.00 sq.mm
Tension does not occur.
Pressure on foundation ( Pr dlo )
= 0.13 N/sq.mm
Maximum Bearing Pressure ( PR max )
= 0.13 N/sq.mm
Actual FOS against Overturning about X-axis
= 70.58 [Dead Load Case]
Actual FOS against Overturning about Y-axis
= 125.92 [Dead Load Case]
Actual percentage of Contact area
= 100.00 [Dead Load Case]
Factored Load Calculation (For Shear and Moment Calculation)
Factored Vertical Load from Column in Combination No. 1 ( P u1 )
= 1287000.00 N
Factored Vertical Load from Column in Combination No. 2 ( P u2 )
= 0.00 N
Factored Vertical Load from Column in Combination No. 3 ( P u3 )
= 0.00 N
Factored Vertical Load from Column in Combination No. 4 ( P u4 )
= 0.00 N
Factored Vertical Load from Column in Combination No. 5 ( P u5 )
= 0.00 N
Factored Shear at Column bottom along X-direction in Combination No.1 ( H ux1 )
= 6000.00 N
Factored Shear at Column bottom along X-direction in Combination No.2 ( H ux2 )
= 0.00 N
Factored Shear at Column bottom along X-direction in Combination No.3 ( H ux3 )
= 0.00 N
Factored Shear at Column bottom along X-direction in Combination No.4 ( H ux4 )
= 0.00 N
Factored Shear at Column bottom along X-direction in Combination No.5 ( H ux5 )
= 0.00 N
Factored Shear at Column bottom along Y-direction in Combination No.1 ( H uy1 )
= 21000.00 N
Factored Shear at Column bottom along Y-direction in Combination No.2 ( H uy2 )
= 0.00 N
Factored Shear at Column bottom along Y-direction in Combination No.3 ( H uy3 )
= 0.00 N
Factored Shear at Column bottom along Y-direction in Combination No.4 ( H uy4 )

Print Time/Date: 06/26/2019 11:45 STAAD.etc Release 4.5 Page 5 of 8

 Job No Sheet No Rev
Company Name 6
Engineer Date

Job Title Checked Date

Approved Date

Client File CF1.etc Dt/Tm 22-Apr-2019 16:26

Calculation, cont...

= 0.00 N
Factored Shear at Column bottom along Y-direction in Combination No.5 ( H uy5 )
= 0.00 N
Factored Moment at Foundation bottom along X-direction in Combination No.1 ( M ux1 )
= 45300000.00 Nmm
Factored Moment at Foundation bottom along X-direction in Combination No.2 ( M ux2 )
= 0.00 Nmm
Factored Moment at Foundation bottom along X-direction in Combination No.3 ( M ux3 )
= 0.00 Nmm
Factored Moment at Foundation bottom along X-direction in Combination No.4 ( M ux4 )
= 0.00 Nmm
Factored Moment at Foundation bottom along X-direction in Combination No.5 ( M ux5 )
= 0.00 Nmm
Factored Moment at Foundation bottom along Y-direction in Combination No.1 ( M uy1 )
= 19950000.00 Nmm
Factored Moment at Foundation bottom along Y-direction in Combination No.2 ( M uy2 )
= 0.00 Nmm
Factored Moment at Foundation bottom along Y-direction in Combination No.3 ( M uy3 )
= 0.00 Nmm
Factored Moment at Foundation bottom along Y-direction in Combination No.4 ( M uy4 )
= 0.00 Nmm
Factored Moment at Foundation bottom along Y-direction in Combination No.5 ( M uy5 )
= 0.00 Nmm
Design Pressure in Combination No.1 ( PR design1 )
= 0.15 N/mm 2
Design Pressure in Combination No.2 ( PR design2 )
= 0.00 N/mm 2
Design Pressure in Combination No.3 ( PR design3 )
= 0.00 N/mm 2
Design Pressure in Combination No.4 ( PR design4 )
= 0.00 N/mm 2
Design Pressure in Combination No.5 ( PR design5 )
= 0.00 N/mm 2
Final Design Pressure ( PR design )
= 0.15 N/mm 2
Calculation of Shear and Moments
Distance of critical Section for shear from Column Face
= 372.00 mm
Shear force at the critical section (Parallel to Y-axis) on left of Left column (S x11 )
= 121.14 N/mm length
Shear force at the critical section (Parallel to Y-axis) on right of Left column (S x21 )
= 32.48 N/mm length
Shear force at the critical section (Parallel to Y-axis) on right of Right column (S x12 )
= 121.14 N/mm length
Shear force at the critical section (Parallel to Y-axis) on left of Right column (S x22 )
= 32.48 N/mm length
Shear force at the Critical Section (parallel to X-axis) (S y )
= 117.48 N/mm length
Moment at section at left face of Left column (M bx11 )
= 105339.51 N-mm/mm length
Moment at section at right face of Left column (M bx21 )
= 136063.53 N-mm/mm length

Print Time/Date: 06/26/2019 11:45 STAAD.etc Release 4.5 Page 6 of 8

 Job No Sheet No Rev
Company Name 7
Engineer Date

Job Title Checked Date

Approved Date

Client File CF1.etc Dt/Tm 22-Apr-2019 16:26

Calculation, cont...

Moment at section at right face of Right column (M bx12 )

= 105339.51 N-mm/mm length
Moment at section at left face of Right column (M bx22 )
= 136063.53 N-mm/mm length
No tension occurs at top of footing from Bending Moment Diagram
Design Shear Force at section parallel to Y-axis (S xdesign )
= 121.14 N/mm length
Design Shear Force at section parallel to X-axis (S ydesign )
= 117.48 N/mm length
Maximum Design bottom Moment (from bending moment diagram )at section parallel to Y-axis (M bxdesign )
= 136063.53 N-mm/mm length
Maximum Design top Moment (from bending moment diagram )at section parallel to Y-axis (M txdesign )
= 0.00 N-mm/mm length
Maximum Design bottom Moment (from bending moment diagram )at section parallel to X-axis (M bydesign )
= 100996.08 N-mm/mm length
Maximum Design top Moment (from bending moment diagram )at section parallel to X-axis (M tydesign )
= 0.00 N-mm/mm length
Calculation of Bottom Reinforcement of the footing
Effective Thickness for Steel Calculation along X-direction at bottom (D bx )
= 384.00 mm
Effective Thickness for Steel Calculation along Y-direction at bottom (D by )
= 372.00 mm
Effective Thickness for Steel Calculation along X-direction at top (D tx )
= 384.00 mm
Effective Thickness for Steel Calculation along Y-direction at top (D ty )
= 372.00 mm
Maximum Value of M u / bd 2 for steel calculation along X-direction at bottom (M ubd2bx )
= 0.92 N/mm 2
Maximum Value of M u / bd 2 for steel calculation along Y-direction at bottom (M ubd2by )
= 0.73 N/mm 2
2
Maximum Value of M u / bd for steel calculation along X-direction at top (M ubd2tx )
= 0.00 N/mm 2
2
Maximum Value of M u / bd for steel calculation along Y-direction at top (M ubd2ty )
= 0.00 N/mm 2
Required Reinforcement along X-direction at Bottom ( Ast bx )
= 1039.82 mm 2 /m length
Required Reinforcement along Y-direction at Bottom ( Ast by )
= 786.46 mm 2 /m length
Spacing Provided for Reinforcement along X-direction at Bottom (S bxprov )
= 105.00 mm
Spacing Provided for Reinforcement along Y-direction at Bottom (S byprov )
= 140.00 mm
Provided Reinforcement along X-direction at Bottom ( Ast bxprov )
= 1077.12 mm 2 /m length
Provided Reinforcement along Y-direction at Bottom ( Ast byprov )
= 807.84 mm 2 /m length
Provided percentage of Reinforcement along X-direction at bottom ( Pt bxprov )
= 0.28 %
Provided percentage of Reinforcement along Y-direction at bottom ( Pt byprov )
= 0.22 %
Calculation of Shear Stress
Shear Stress along X-direction for bottom pressure ( τ vx )

Print Time/Date: 06/26/2019 11:45 STAAD.etc Release 4.5 Page 7 of 8

 Job No Sheet No Rev
Company Name 8
Engineer Date

Job Title Checked Date

Approved Date

Client File CF1.etc Dt/Tm 22-Apr-2019 16:26

Calculation, cont...

= 0.32 N/mm 2
Shear Stress along Y-direction for bottom pressure ( τ vy )
= 0.32 N/mm 2
Allowable Shear Stress along X-direction for bottom ( τ cx )
= 0.38 N/mm 2
Allowable Shear Stress along Y-direction for bottom ( τ cy )
= 0.34 N/mm 2
Calculation of Concrete Quantity
Quantity of concrete
= 4.331 m3

Print Time/Date: 06/26/2019 11:45 STAAD.etc Release 4.5 Page 8 of 8

Block A
STRUCTURAL DESIGN (Type B)
Building Elements As Per Submitted Design Remark

General

Building Structure Type √ Frame Structure

Number of storeys applied for permit (in Nos.) 3

Number of storeys considered in structural design (in Nos.) 3

If Computer Aided Design (CAD) is used, please State the name ETABS 2016 16.2.1
of the software package

Number of storeys considered in the design provision for Yes

further extension √ No

Total height (h) of structure with extension(in m) 12.00

NBC 101-1994 MATERIALS SPECIFICATIONS

Structural Aluminium
√ Brick Masonry
Timber
Materials to be used in structure(tick the listed materials that will Structural Steel
be used in structure element) √ RCC(Reinforcement Bar)
Stone Masonry

NBC 102-1994 Unit Weight of Materials

Specify the design unit weight of materials: Steel (in kg/m3) 7850

Specify the design unit weight of materials: RCC (in kg/m3) 2500

Specify the design unit weight of materials: Brick Masonry (in 1920
kg/m3)

NBC 103-1994 Occupancy Load (Imposed Load)

For Residential buildings

Occupancy Load (Uniformly Distributed load in kN/m2) for 2.5

Office Rooms

Occupancy Load (Uniformly Distributed load in kN/m2) for 4

Corridors, Staircase, Store
Occupancy Load (Uniformly Distributed load in kN/m2) for 4
Balcony

NBC 104-1994 Wind load

Wind Zone 1

Basic wind speed (in m/s) 47

NBC 105-1994 Seismic Design of Buildings in Nepal

√ Seismic Coefficient
Approach
Response Spectrum
Method
Method adopted for earthquake resistant design Others
Adopted Code for Seismic Design √ NBC 105

√ Type I (Hard)
Type II (Medium)
Subsoil category Type III (Soft)
Seismic Weight (W) (in kN) 5787.28

Fundamental Time Period of the building along X (Tx)(in Seconds)

0.39

Fundamental Time Period of the building along Y(Ty)(in

Seconds) 0.39

Basic Seismic Coefficient Along X(C) 0.08

Basic Seismic Coefficient Along Y(C) 0.08

Seismic zoning factor (Z) 1

Importance Factor (I) 1.5

Structural Performance factor (K) (if NBC used) 1

Design Horizontal Seismic Coefficient Along X(Cd) 0.12

Design Horizontal Seismic Coefficient Along Y(Cd) 0.12

Base Shear(VB) for Seismic Coefficient Along X 694.47

Base Shear(VB) for Seismic Coefficient Along Y 694.47

Base Shear Generated through dynamic Analysis Along X (if

response spectrum method used) -

Base Shear Generated through dynamic Analysis Along Y (if

response spectrum method used) -

Adopted Base Shear multiplication Factor Along X(if response

spectrum method used) -
Adopted Base Shear multiplication Factor Along Y(if response
spectrum method used) -

Base Shear after Scale Factor Along X -

Base Shear after Scale Factor Along Y -

Maximum Inter-storey Drift 7.92

Corresponding Storey height for Maximum Inter- Storey Drift (h)

3300.00

NBC 106-1994 Snow Load

Snowfall type or condition Perennial

Occasional
√ No snowfall
Elevation of construction site (in m)

Design Depth of snow (in cm)

Design Density of snow (in g/cm3)

NBC 107-1994 Provisional Recommendation on Fire Safety

Have you considered fire safety requirement? Yes

No
NBC 108-1994 Site Consideration for Seismic Hazards

Whether Distance of construction site from toe/beginning Yes

of downward slope is within 50m? No
Whether Distance of construction site from river bank is within Yes
50m? No

Availability of soil test report Yes

√ No
NBC 114-1994 Construction Safety

Are you sure that all safety measures will be fulfilled in the √ Yes
construction site as per this code? No

√ Safety hard hat

√ Safety goggles
√ Safety boots
Safety wares used
√ Safety belts
√ First aid facility

Structural Data for Framed RCC Structure

NBC 110-1994 Plain and Reinforced Concrete

√ M20
M25
Concrete grade in structure
M30
M35
 Fe-415
√ Fe-500
Fe-550
Reinforcement Steel Grade
Slab design

4 side continuous
1 short side
discontinuous
1 long side
discontinuous
√ 2 adjacent side
continuous
2 long side
Boundary condition of slab continuous
2 short side
continuous
1 long side
continuous
1 short side
continuous
4 side
discontinuous

Effective Thickness of slab (d) (in mm) 97

Short span of Critical slab panel (L) (in mm) 4200.00

Calculated short span to effective depth ratio (L/d) for the 43.30
corresponding slab

Basic (L/d) ratio 26

Required modification factor for tension reinforcement 1.66

Required Tension reinforcement(Ast) Percentage(%) 0.201

for short span bottom reinforcement

Provided Tension reinforcement(Ast) Percentage (%) for short span 0.268

bottom reinforcement

Actual Modification factor for tension reinforcement 1.8

Check for Critical beam

Effective depth of beam (d) (in mm) 365

Critical span (L) (in mm) 4500.00

Cantilever
Simply supported
√ One side continuous

Both side
Support condition continuous
Basic (L/d) ratio 23

Calculated critical span to effective depth ratio (L/d) for 12.33

corresponding slab

Check for Critical Column

Critical column height 3.30

Minimum size of column (mm x mm) 400 X 400

Short column effect considered or not √ Yes

No

Minimum area of longitudinal reinforcement provided (%)

1.07%

Design Philosophy Limit state method

Load Combinations

1: DL 1.5

1: LL 1.5

1: EQ 0

2: DL 1

2: LL 1.3

2: EQ 1.25

3: DL 0.9

3: LL 0

3: EQ 1.25

4: DL 1

4: LL 0

4: EQ 1.25

Whether sample design calculations of foundations, columns, beams √ Yes

and slabsare submitted No

√ Isolated
√ Combined
Type of Foundations  Raft
PILE
 Strap
Depth of foundation from ground level to the bottom of footing
(in m) 1.5