International

standards on technical
documentation
documentation

International Electrotechnical Commission

International standards on
technical documentation
Standards on technical documentation developed by the IEC
address the following important business trends:

Documentation is part of the product, system or

installation
Users and societies are increasingly dependent on complex
systems. The demand for installations or systems that are
safe, easy to operate and to maintain is increasing.

Documents and information from different sources need to

be integrated
Companies concentrate on their core business and purchase
products and subsystems from other suppliers. Consequently,
the complete documentation comprises several subsets that
will be exchanged and studied together.

Multidisciplinary environment
Complex systems often involve different technologies, of
which electrotechnology is one. This calls for co-ordinated
methods and rules over the technological boundaries.
Standardization therefore has to be run in close co-operation
with similar standards bodies for other areas.

The whole life cycle of a product, system or installation

needs documentation
Documents link the different phases of the life cycle.
Standardization will focus on the requirements for engineering
and manufacturing, and also on the earlier and later phases in
the cycle.

2
Information technology changes the products, systems and
installations
The use of information technology in plants and installations
standardizes the connections among components further, and
the traditional documentation of circuits can be expected to
decrease in importance. However, documentation on higher
conceptual levels (which are not necessarily “electrical”) can
be expected to increase in importance. Electronic documenta-
tion will to a high degree either be physically integrated into
the product or made available via computer networks.

Information technology changes the engineering and docu-

mentation process
From computer aided drawing systems and the presentation
of the visual image of a document, systems have developed
into highly complex data modelling systems storing the cap-
tured information in a database. A document is becoming the
representation of such stored information, generated by pre-
defined electronic templates.

IEC TC 3

Initially entrusted with overall responsibility for standardizing

symbols of the IEC, Technical Committee 3 (Documentation
and graphical symbols), also strives to meet the market needs
which result from the present trends.
Work is managed by TC 3 – also in charge of the newly cre-
ated Symbols Database and of Symbols for Diagrams – and
allocated to three subcommittees.

SC 3B, covering documentation, establishes rules for prepar-

ing documentation, diagrams, reference designations, and
presentation of the information with a view towards electronic
exchange. SC 3C is in charge of graphical symbols for use on
equipment, and SC 3D deals with data sets for libraries to en-
able handling the information in a computer sensible form.
TC 3 co-operates with other standardization bodies active in
this field, notably ISO.

The main publications

Users may access the Symbols Database, which is drawn from

IEC 60617 and 60417, and consult publications which cover a
wide range of topics in the field of technical documentation. A
complete list appears in the inlay of this pamphlet.

IEC 60617 contains more than 1 200 internationally recog-

nized symbols for diagrams and indexes.

IEC 60417 contains more than 650 internationally recognized

symbols for use on electrotechnical equipment and relevant
surveys.

4
IEC 61082 provides rules for preparing the kinds of docu-
ments used most widely, while IEC 60848 defines language
GRAFCET for sequential function charts.

IEC 61346 is a very basic standard covering principles for

structuring technical information and related identification
needs. Relying on this are, among others, IEC 61175 and
IEC 61666.

IEC 61355 defines the kinds of documents to be used in a

system documentation and their classification.

A number of standards are more directed to preparing and

handling documentation with a goal to make the information
sensible to computers. This includes:

— IEC 61360, which provides unambiguous definitions and

identifications for component information.

— IEC 61286, which provides a character set specifically

developed for electrotechnical purposes.

— IEC 81714, which contains (besides basic design rules of

graphical symbols) information on how to associate techni-
cal data with graphical symbols in CAD systems.

5
Current work

TC 3 regularly revises and updates existing standards.

At present, this is the case for IEC 60617, IEC 60417 and
IEC 61360.

To serve industry needs for quick updating and easy

electronic access to standards, procedures are now
being established in connection with creation of an
online database of symbols. This will allow standardi-
zation work and publication to be carried out "piece
by piece" via the internet.

New topics under discussion include: rules for the preparation

of documents such as instructions and parts lists; classifica-
tion and coding of objects; application guidelines for the refer-
ence designation system; classification and coding of shapes
of electric components for placement on printed wiring
boards.

Through a joint working group, IEC TC 3 also takes an

active part in developing standardized information models for
electrotechnical systems and equipment of ISO 10303
(STEP): Application Protocol AP210 and AP212.

6
Future work

Projects that are under consideration include: meta data for

document management; integrated software and hardware
documentation; further work on data element type definitions
in co-operation with relevant committees.

IEC

The IEC has served the world's electrical industry since 1906,
developing international standards to promote quality, safety,
performance, reproducibility and environmental compatibility of
materials, products and systems.

The world-wide use of IEC standards supports the

transfer of electrotechnology, assists certification and pro-
motes international trade of uniform high-quality products and
services. International standards establish objective specifica-
tions that both buyer and seller can rely on. For buyers, they
widen the range of choices and lower costs, primarily because
they often increase the number of competitors. For sellers,
global standards broaden the number of potential customers
and reduce the cost of meeting their needs. In short, for every-
one in society, international standards raise the overall
efficiency and productivity of the economy.

The IEC membership, which now comprises more than 50

countries, includes all the world's major trading nations. This

7
membership collectively represents about 85 percent of the
world's population and 95 percent of the world's electrical
generating capacity.

More information

More information about the work on documentation standards

carried out in IEC TC 3 can be obtained through any of the
National Committees of the IEC, the addresses of which are
available from the IEC Central Office or from the secretary of
any IEC TC.

Up-to-date information about the work items under discussion

can be obtained from the IEC's website, at http://www.iec.ch
and that of TC3 at http://www.iec.ch/tc3 .

8
 The IEC’s website may be found at: www.iec.ch.
For further information

For further information about the IEC, please contact

Central Office at the co-ordinates below.

International Electrotechnical
Commission

3, rue de Varembé, CH-1211 Geneva 20,

Switzerland
Telephone: +41 22 919 02 11
Telefa x: +41 22 919 03 00
E-mail: [email protected]
U R L: http://www.iec.ch 2000-01
 List of standards pre-
pared by Technical
Committee 3 of
the I E C
documentation
standards
International Electrotechnical Commission

● Structuring, identification, and related topics

IEC 61346-1 (1996) Industrial systems, installations and
equipment and industrial products -
Structuring principles and reference
designations - Part 1: Basic rules
IEC 61346-4 (1998) Industrial systems, installations
and equipment and industrial
products - Structuring principles
and reference designation - Part 4
Discussions of concept

IEC 61175 (1993) Designations for signals and

connections
IEC 61666 (1997) Industrial systems, installations and
equipment and industrial products -
Identification of terminals within a
system

● Documentation and document kind definitions

IEC 61355 (1997) Classification and designation of

documents for plants, systems and
equipment
10
● Preparation of various document kinds

IEC 60848 (1988) Preparation of function charts for

control systems
IEC 61082-1 (1991) Preparation of documents used in
electrotechnology - Part 1:
General requirements
IEC 61082-2 (1993) Preparation of documents used in
electrotechnology - Part 2:
Function-oriented diagrams
IEC 61082-3 (1993) Preparation of documents used in
electrotechnology - Part 3:
Connection diagrams, tables and
lists
IEC 61082-4 (1996) Preparation of documents used
in electrotechnology - Part 4:
Location and installation documents
IEC 61082-6 (1997) Preparation of documents used in
electrotechnology - Part 6: Index

● Graphical symbols for diagrams

Standards for symbol appearance

IEC 60617-1 (1985) Graphical symbols for diagrams. Part

1: General information, general index.
Cross-reference tables
IEC 60617-2 (1996) Graphical symbols for diagrams - Part
2: Symbol elements, qualifying
symbols and other symbols having
general application
IEC 60617-3 (1996) Graphical symbols for diagrams - Part
3: Conductors and connecting
devices
IEC 60617-4 (1996) Graphical symbols for diagrams - Part
4: Passive components
IEC 60617-5 (1996) Graphical symbols for diagrams - Part
5: Semiconductors and electron
tubes

11
IEC 60617-6 (1996) Graphical symbols for diagrams -
Part 6: Production and conversion of
electrical energy
IEC 60617-7 (1996) Graphical symbols for diagrams -
Part 7: Switchgear, controlgear and
protective devices
IEC 60617-8 (1996) Graphical symbols for diagrams - Part
8: Measuring instruments, lamps and
signalling devices
IEC 60617-9 (1996) Graphical symbols for diagrams - Part
9: Telecommunications: Switching
and peripheral equipment
IEC 60617-10 (1996) Graphical symbols for diagrams - Part
10: Telecommunications:
Transmission
IEC 60617-11 (1996) Graphical symbols for diagrams - Part
11: Architectural and topographical
installation plans and diagrams
IEC 60617-12 (1991) Graphical symbols for diagrams - Part
12: Binary logic elements
IEC 60617-13 (1993) Graphical symbols for diagrams - Part
13: Analogue elements
IEC 61734 (1997) Application of IEC 60617-12 and IEC
60617-13 standards

Supporting standards (ISO/IEC standards)

ISO 11714-1 (1996) Design of graphical symbols for use

(future ISO 81714-1-1) in the tech-
nical documentation of products. Part
1: Basic rules.
IEC 81714-2 (1998) Design of graphical symbols for use
in the technical documentation of
products. Part 2: Specification for
graphical sym-bols in a computer
sensitive form including graphical

12
 symbols for a reference library, and
requirements for their interchange.
IEC 81714-3 (1998) Design of graphical symbols for use
in the technical documenta-tion of
products. Part 3: Classification of
connect nodes, networks and their
encoding.
IEC 61286 (1995) Information technology - Coded
graphic character set for use in the
preparation of documents used in
electrotechnology and for information
interchange

● Graphical symbols to be used on equipment

Standard for symbol appearance

IEC 60417* Graphical symbols for use on equipment. Index,

survey and compilation of the single sheets

Supporting standard (ISO/IEC standard)

IEC 60416 (1988) General principles for the formulation of graphi-

cal symbols

*Updated regularly.
13
● Data element types

IEC 61360-1 (1995) Standard data element types with

associated classification scheme
for electric components - Part 1:
Definitions - Principles and meth-
ods
IEC 61360-2 (19958 Standard data element types with
associated classification scheme
for electric components - Part 2:
Express dictionary schema.
IEC 61360-3 (1995) Standard data element types with
associated classification scheme
for electric components - Part 3:
Maintenance and validation pro-
cedures
IEC 61360-4 (1997) Standard data element types with
associated classification scheme
for electric components - Part 4:
IEC reference collection of stan-
dard data element types, compo-
nent classes and terms

14
 More information about the work on documentation
For further information

standards carried out in IEC TC3 can be obtained

through any of the National Committees of the IEC,
the addresses of which are available from the IEC
Central Office or from the secretary of any IEC TC.

Up-to-date information about the work items under

discussion can be obtained from the IEC website at
http://www.iec.ch and that of TC3 at
http://www.iec.ch/tc3

International Electrotechnical
Commission

3, rue de Varembé, CH-1211 Geneva 20,

Switzerland
Telephone: +41 22 919 02 11
Telefa x: +41 22 919 03 00
E-mail: [email protected]
U R L: http://www.iec.ch 2000-01