Scribd
Upload
234 views3 pages

IO-0210 User Manual V10.en

The IO-0210 board provides 2 programmable inputs and 10 transistor outputs. It can be programmed to assign outputs to different groups using dip switches. Dip switches 1-2 select the output group, while dip switches 3-8 allow programming up to 64 unique boards by setting a binary coded identification number. LED indicators show the status of power, microcontroller operation, and outputs. Programmable inputs and outputs are configured through device parameter menus in the control software.

Uploaded by

Вячеслав Якимов
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
234 views3 pages

IO-0210 User Manual V10.en

The IO-0210 board provides 2 programmable inputs and 10 transistor outputs. It can be programmed to assign outputs to different groups using dip switches. Dip switches 1-2 select the output group, while dip switches 3-8 allow programming up to 64 unique boards by setting a binary coded identification number. LED indicators show the status of power, microcontroller operation, and outputs. Programmable inputs and outputs are configured through device parameter menus in the control software.

Uploaded by

Вячеслав Якимов
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

IO-0210 BOARD: In some cases, programmable inputs and outputs can’t be enough.

Then, this
IO-0210 board would be useful. This board gives 2 inputs and 10 transistor outputs to the user.

The explanations according to the arrow numbers:


1)Dip-switch settings: As you see in the Picture of IO-0210 board, there are 8 dip-switches. The logic
of these dip-switches is as follows:
1 and 2 dipswitches are used to select the group number of output:

1 2 Prog.output
OFF OFF 1st group
OFF ON 2nd group
ON OFF 3rd group
ON ON 4th group

For example;

If both of them is OFF position, it is selected as “1st group”.


If “1” is ON, ”2” is OFF, it is selected as “3rd group”.

Other 6 dipswitches (from 3(MSB) to 8(LSB)) works with a binary logic. For example;
MSB: Most Significant Bit (3rd dip-switch)
LSB: Least Significant Bit (8th dip-switch)
You can program 64 different IO-0210 boards for inputs.
000000 “IO-0210-1 board PI1 and IO-0210-1 board PI2”
000001 “IO-0210-2 board PI1 and IO-0210-2 board PI2”
000010 “IO-0210-3 board PI1 and IO-0210-3 board PI2”
000011 “IO-0210-4 board PI1 and IO-0210-4 board PI2”
000100 “IO-0210-5 board PI1 and IO-0210-5 board PI2” and so on...
This can be chosen from 0 up to 63. (64 pcs.)
3 4 5 6 7 8 IO-0210-x
OFF OFF OFF OFF OFF OFF 1
OFF OFF OFF OFF OFF ON 2
OFF OFF OFF OFF ON OFF 3
OFF OFF OFF OFF ON ON 4
OFF OFF OFF ON OFF OFF 5

Here are some examples of dip-switch settings:

“1st group output”


“IO-0210-1 board PI1 input and
IO-0210-1 board PI2 input”
“2nd group output”
“IO-0210-3 board PI1 input and
IO-0210-3 board PI2 input”

“4th group output”


“IO-0210-14 board PI1 input and
IO-0210-14 board PI2 input

2) MCU: By observing the behaviour of this LED, You can understand whether this board is working
well or not. It should blink synchronously. (If MCU is blinking with 1 long, 1 short time, the version
of ARCODE and IO-0210 are not proper. It needs to be updated from –AREM “tools -> firmware
update” after connected all units to CANbus line. Then, they will blink synchronously.)
3) 100 LED: This should give out a stable green light. If it is ON, 24V supply is good. If it is OFF,
there is no 24 V supply.
4) X-CB1 and X-CB2 sockets are CANbus connections of the board. (Big and small size)
5) VCC LED: If it is stable green light, it means that the board is supplied well.
6) PROGRAMMABLE OUTPUTS: As mentioned above, this board gives 10 transistor outputs.
You can adjust them from parameter. (Tools  device parameters  programmable outputs 
IO0210 board outputs) The number of group outputs are adjusted with dip-switches 1 and 2.
7) PI INPUTS: IO-0210 board has 2 inputs. According to the dip-switches you adjusted, you can use
it. (Tools  device parameters  programmable inputs  IO-0210 board inputs)

You might also like