MODEL

834-05
800 Series (Tubular Diaphragm Valve)

Fire Deluge Valve

• Low Head Loss
• Cast Steel Construction
• Stainless Steel Pilot and Tubing
• Stainless Steel Solenoid
• Anti-Cavitation Design
• Fusion Coated Epoxy Inside and Out
• Nickel Aluminum Bronze Construction Option (Alloy C95800)
• Duplex Stainless Steel Construction Option (Alloy 2205)
• Low Maintenance
• Simple and Reliable Operation
• 1-Year Warranty

The Cla-Val 834-05 Deluge Valve is a pressure-operated, in-line axial

valve. A tube diaphragm actuates the valve, which is comprised of
three major components: 1) Tube 2) Barrier and 3) Body. There is only
one moving part in the valve - the tube diaphragm. There are no shafts,
packing, stem guides or springs.
The tube diaphragm is a one piece, homogeneous nitrile rubber part
which is extremely durable. The ends of the tube are thick solid rubber,
designed to fit between mating flanges. This design eliminates the pos-
sibility of cutting the tube diaphragm due to over tightening or piping mis-
alignment during installation.
The tube forms a drip tight seal around the barrier when the pressure
is equalized between the valve inlet and the control chamber. When
pressure is removed from the control chamber, the valve is open. The
minimum recommended operating pressure is 40 P.S.I. of inlet pressure.

Principle of Operation Control Options

Electric Operation
Pneumatic Operation
Hydraulic Operation
Manual Operation

Inlet Outlet Inlet Outlet

FLOW FLOW

Full Open Operation Tight Closing Operation

When pressure in control chamber Water pressure from valve inlet is

is relieved, the valve is open. applied to the control chamber.
Valve closes bubble tight.
 Model 834-05
Dimensions
Valve Size (Inches) 4 6 8 10
"L" L 17.25 18.25 20.00 22.00
D 9.5 11.75 14.00 16.00
T-2
T-1/T-2 (NPT) 1/2 1/2 1/2 1/2
T-3 (NPT) 2 2 2 2
T-1 T-1 Approx. Wt. (Lbs.) 151 196 285 330
Valve Size (mm) 100 150 200 250
L 438 464 508 559
D 241 299 356 406
T-1/T-2 (NPT) 1/2 1/2 1/2 1/2
"D"
T-3 (NPT) 2 2 2 2
Approx. Wt. (kgs) 68 89 129 150

4”, 6”, 8” FLOW FACTORS

Factory Mutual
Approved SIZE (IN) CV (gpm) KV
T-3 T-3
(with approved 4” 340 77.3
T-2 Pilot 6” 885 201
FLOW Components) 8” 1667 379
*10” 2424 550
*Calculated

MAIN VALVE
Ends: Flanged ANSI B16.5 (150lb Class)
Body: Cast Steel (ASTM A216 WCB)
Tube Diaphragm: Nitrile Rubber
Barrier: Urethane
Bolts: 316 SS
Pressure: 250 psig (17.24 BAR)
Temp. Range: 32º F to 180º F (0º C to 82.2º C)

MAIN VALVE OPTIONS

Body: Nickel Aluminum Bronze
(Alloy C95800) or
Duplex SS (Alloy 2205)

PILOT VALVE
All Parts: Bronze / Monel
O-Rings: Nitrile Rubber
Control Range: 20 to 250 PSIG
Pilot Pressure Range: 20 to 250 PSIG
Operation: Latches in operated position;
manual reset
PILOT VALVE OPTIONS
Item Description Item Description
All Parts: Monel (Alloy 400)
1 800GS TDV Main Valve 9 Pressure Switch Operation: Non-latching
2 X43 “Y” Strainer 10 CGA Angle Valve
3 CS3 Solenoid Control 11 Automatic Drain Valve
4 Latching Deluge Pilot 12 Pressure Gauge
5 X58C Restriction Assembly
6 CK2 Cock (Isolation Valve)
Cla-Val 800 Series Control Valves operate with maximum efficiency when mounted in horizontal or vertical piping. We recommend isolation valves
be installed on inlet and outlet for maintenance. Adequate space above and around the valve for service personnel should be considered essential.
A regular maintenance program should be established based on the specific application data. However, we recommend a thorough inspection
be done at least once a year. Consult factory for specific recommendations.

CLA-VAL Represented By:

PO Box 1325 Newport Beach CA 92659-0325 Phone: 949-722-4800
Fax: 949-548-5441 Web Site: cla-val.com E-mail: [email protected]
CLA-VAL CANADA CLA-VAL EUROPE CLA-VAL UK
4687 Christie Drive Chemin des Mésanges 1 Dainton House, Goods Station Road
Beamsville, Ontario CH-1032 Romanel/ GB - Tunbridge Wells
Canada L0R 1B4 Lausanne, Switzerland Kent TN1 2 DH England
Phone: 905-563-4963 Phone: 41-21-643-15-55 Phone: 44-1892-514-400
Fax: 905-563-4040 Fax: 41-21-643-15-50 Fax: 44-1892-543-423
E-Mail: [email protected] E-Mail: [email protected] E-Mail: [email protected]
E-834-05 (R-10/2010) © Copyright CLA-VAL 2010 Printed in USA Specifications subject to change without notice.