HFA08SD60S: Ultrafast, Soft Recovery Diode

Download as pdf or txt
Download as pdf or txt
You are on page 1of 7

Bulletin PD-20618 rev.

D 10/06

HFA08SD60S
Ultrafast, Soft Recovery Diode
Features
t rr = 18ns
• Ultrafast Recovery Time
• Ultrasoft Recovery IF(AV) = 8Amp
• Very Low IRRM
• Very Low Qrr VR = 600V
• Guaranteed Avalanche
• Specified at Operating Temperature

Benefits
• Reduced RFI and EMI
• Reduced Power Loss in Diode and
Switching Transistor
• Higher Frequency Operation
• Reduced Snubbing
• Reduced Parts Count

Description/ Applications Package Outline

These diodes are optimized to reduce losses and EMI/RFI in


high frequency power conditioning systems. The softness of
the recovery eliminates the need for a snubber in most
applications. These devices are ideally suited for freewheeling,
flyback, power converters, motor drives, and other applications
where high speed and reduced switching losses are design
requirements.

D - PAK

Absolute Maximum Ratings


Parameters Max Units
VRRM Cathode-to-Anode Voltage 600 V
IF(AV) Continuous Forward Current 8 A
TC = 100°C
IFSM Single Pulse Forward Current 60
IFRM Peak Repetitive Forward Current 24
PD Maximum Power Dissipation 14 W
TC = 100°C
TJ, TSTG Operating Junction and Storage Temperatures - 55 to 150 °C

www.irf.com 1
HFA08SD60S
Bulletin PD-20618 rev. D 10/06

Electrical Characteristics @ TJ = 25°C (unless otherwise specified)


Parameters Min Typ Max Units Test Conditions
VBR, Vr Breakdown Voltage, 600 - - V IR = 100µA
Blocking Voltage
VF Forward Voltage - 1.4 1.7 V IF = 8A
See Fig. 1 - 1.7 2.1 V IF = 16A

- 1.4 1.7 V IF = 8A, TJ = 125°C


IR Max. Reverse Leakage Current - 0.3 5.0 µA VR = VR Rated

- 100 500 µA TJ = 125°C, VR = 0.8 x VR Rated


CT Junction Capacitance - 10 25 pF VR = 200V

LS Series Inductance - 8.0 - nH Measured lead to lead 5mm from package body

Dynamic Recovery Characteristics @ TJ = 25°C (unless otherwise specified)


Parameters Min Typ Max Units Test Conditions
trr Reverse Recovery Time - 18 - ns IF = 1.0A, diF/dt = 200A/µA, VR = 30V
- 37 55 TJ = 25°C IF = 8A
- 55 90 TJ = 125°C VR = 200V
diF /dt = 200A/µs
IRRM Peak Recovery Current - 3.5 5.0 A TJ = 25°C

- 4.5 8.0 TJ = 125°C

Qrr Reverse Recovery Charge - 65 138 nC TJ = 25°C

- 124 360 TJ = 125°C


di(rec)M/dt Rate of Fall of recovery Current - 240 - A/µs TJ = 25°C

- 210 - TJ = 125°C

Thermal - Mechanical Characteristics


Parameters Min Typ Max Units
TJ Max. Junction Temperature Range - - - 55 to 150 °C

TStg Max. Storage Temperature Range - - - 55 to 150

Tlead Lead Temperature - - 300

RthJC Thermal Resistance, Junction to Case - - 3.5 °C/ W


RthJA  Thermal Resistance, Junction to Ambient - - 80
Wt Weight - 2.0 - g
- 0.07 - (oz)
 Typical Socket Mount

2 www.irf.com
HFA08SD60S
Bulletin PD-20618 rev. D 10/06

100 1000
T J = 150˚C

100

(µA)
125˚C
10

R
Reverse Current - I
1
25˚C
0.1

10
0.01
(A) F

0.001
Instantaneous Forward Current - I

0 100 200 300 400 500 600


Reverse Voltage - V R (V)
Fig. 2 - Typical Values Of Reverse Current
Vs. Reverse Voltage
100
Junction Capacitance - C T (pF) T J = 25˚C
1
T = 150˚C
J
T = 125˚C
J 10
T = 25˚C
J

0.1 1
0.4 0.8 1.2 1.6 2 2.4 2.8 3.2 3.6 4 1 10 100 1000
Forward Voltage Drop - V FM (V) Reverse Voltage - V R (V)
Fig. 1 - Typical Forward Voltage Drop Characteristics Fig. 3 - Typical Junction Capacitance
Vs. Reverse Voltage
10
(°C/W)

D = 0.50
thJC

D = 0.20
1 D = 0.10
Thermal Impedance Z

D = 0.05 PDM
D = 0.02
D = 0.01 t1
t2
0.1 Single Pulse
(Thermal Resistance) Notes:
1. Duty factor D = t1/ t2
2. Peak Tj = Pdm x ZthJC + Tc
0.01
0.00001 0.0001 0.001 0.01 0.1 1
t1, Rectangular Pulse Duration (Seconds)
Fig. 4 - Max. Thermal Impedance Z thJC Characteristics

www.irf.com 3
HFA08SD60S
Bulletin PD-20618 rev. D 10/06

80 20
If = 16A
70 If = 8A
If = 4A If = 16A
15 If = 8A
60
If = 4A

50
trr (ns)

Irr (A)
10
40

30
5
Vr = 200V Vr = 200V
20 Tj = 125˚C Tj = 125˚C
Tj = 25˚C Tj = 25˚C

10 0
100 1000 100 1000
diF /dt (A/ µs) Average Forward Current - IF(AV) (A)

Fig. 5 - Typical Reverse Recovery vs. di F /dt Fig. 6 - Typical Recovery Current vs. di F /dt

500 10000
Vr = 200V Vr = 200V
Tj = 125˚C Tj = 125˚C
Tj = 25˚C Tj = 25˚C
400

If = 16A
If = 8A If = 16A
di (rec)M / dt (A/ µs)

300 If = 4A If = 8A
Qrr ( nC )

If = 4A
1000

200

100

0 100
100 1000 100 1000
di F /dt (A/µs ) di F /dt (A/µs )

Fig. 7 - Typical Stored Charge vs. di F /dt Fig. 8 - Typical di (rec)M /dt vs. di F /dt

4 www.irf.com
HFA08SD60S
Bulletin PD-20618 rev. D 10/06

Reverse Recovery Circuit

VR = 200V

0.01 Ω
L = 70µH
D.U.T.

D
di F /dt
dif/dt
ADJUST G IRFP250

Fig. 9- Reverse Recovery Parameter Test Circuit

3
t rr
IF
ta tb
0

4
Q rr
2
I RRM 0.5 I RRM
di(rec)M/dt 5

0.75 I RRM

1 di fF/dt
/dt

1. diF /dt - Rate of change of current through zero 4. Qrr - Area under curve defined by t rr
crossing and IRRM
t rr x I RRM
2. IRRM - Peak reverse recovery current Q rr =
2
3. trr - Reverse recovery time measured from zero 5. di (rec)M /dt - Peak rate of change of
crossing point of negative going IF to point where current during t b portion of t rr
a line passing through 0.75 IRRM and 0.50 IRRM
extrapolated to zero current

Fig. 10 - Reverse Recovery Waveform and Definitions

www.irf.com 5
HFA08SD60S
Bulletin PD-20618 rev. D 10/06

Outline Table
2.38 (0.09)
6.73 (0.26) 2.19 (0.08) 1.14 (0.04) MINIMUM RECOMMENDED FOOTPRINT
6.35 (0.25) 0.89 (0.03)
5.46 (0.21) 1.27 (0.05) 0.58 (0.02) 5.97 (0.24)
5.21 (0.20) 0.88 (0.03) 0.46 (0.02)
4

6.45 (0.24)
6.22 (0.24) 5.68 (0.22) 6.48 (0.26)
1.64 (0.02)
5.97 (0.23) 10.42 (0.41) 10.67 (0.42)
9.40 (0.37)
1 2 3

0.51 (0.02) 2x
1.52 (0.06) MIN. 2.54 (0.10)
1.15 (0.04)
2.28 (0.09)
0.89 (0.03)
1.14 (0.04) 3x 0.58 (0.02) 1.65 (0.06) 2x
2x 0.64 (0.02)
0.76 (0.03) 0.46 (0.02) 2x
1 - Anode 2
2.28 (0.09) 12 -- NC
Cathode
2x 23 -- Cathode
Anode
4.57 (0.18) 4 - Cathode
3 - Anode
4 - Cathode

Conform to JEDEC outline D-Pak 1 3


Dimensions in millimeters and (inches) N/C Anode

Tape & Reel Information


TRR

1.60 (0.063)
1.50 (0.059)
1.60 (0.063)
4.10 (0.161) DIA.
1.50 (0.059)
3.90 (0.153) 0.368 (0.0145)
0.342 (0.0135)
FEED DIRECTION
1.85 (0 .07 3)
11.60 (0.457)
1.65 (0 .06 5)
11.40 (0.449)
24 .30 (0 .95 7)
15 .42 (0.6 09)
23 .90 (0 .94 1)
TRL 15 .22 (0.6 01)

1.75 (0.06 9)
DIA.
10 .90 (0.4 29) 1.25 (0.04 9)
4.72 (0.186)
10 .70 (0.4 21) 16 .10 (0.6 34) 4.52 (0.178)
15 .90 (0.6 26)

FEED DIRECTION

13.50 (0.532) 26 .40 (1.0 39)


12.80 (0.504) DIA. 24 .40 (0.9 61)

SMD-220 Tape & Reel


When ordering, indicate the part
number,SMD-220 Tape
part orientation, and &theReel
When
quantity. ordering,
Quantities indicate the part
are in multiples
of 800 pieces per reel for both
number, part orientation and the
60 (2 .36 2) TRL and TRR.
360 (14.173) quantity. Quantities are in
D IA . MIN .
DIA. MAX. multiples of 800 pieces per reel
for both TRL and TRR.

6 www.irf.com
HFA08SD60S
Bulletin PD-20618 rev. D 10/06

Marking Information

INTERNATIONAL 2 (K) PART NUMBER


EXAMPLE: THIS IS AN HFA08SD60S
RECTIFIER LOGO
HFA08SD60S

9812
5K3A
ASSEMBLY
LOT CODE DATE CODE (YYWW)
YY = YEAR
NC 3 (A) WW = WEEK

Ordering Information Table

Device Code
HF A 08 SD 60 S

1 2 3 4 5 6

1 - Hexfred Family
2 - Electron Irradiated
3 - Current Rating (08 = 8A)
4 - D-PAK
5 - Voltage Rating (60 = 600V) S = D2PAK/ Dpak
TR = Tape & Reel
6 - Suffix
TRL = Tape & Reel Left
TRR= Tape & Reel Right

Data and specifications subject to change without notice.


This product has been designed and qualified for Industrial Level.
Qualification Standards can be found on IR's Web site.

IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105
TAC Fax: (310) 252-7309
Visit us at www.irf.com for sales contact information. 10/2006

www.irf.com 7

You might also like