Scribd Logo
Upload

Welcome to Scribd!

  • 180 views

    Experiment: Setting and Testing of Differential Relay Using ETAP 1.0 Objective

    Uploaded by

    kashif
    This document describes an experiment to set and test a differential relay using ETAP software. The objectives are to understand how to perform short circuit analysis in ETAP to set the relay and observe its operation during faults. The procedure involves running load flow and short circuit analyses, setting CT ratios and polarities, configuring overcurrent and differential relays, and inserting faults to test coordination and operation of the protection scheme.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Experiment: Setting and Testing of Differential Relay Using ETAP 1.0 Objective

    Uploaded by

    kashif
    180 views2 pages
    This document describes an experiment to set and test a differential relay using ETAP software. The objectives are to understand how to perform short circuit analysis in ETAP to set the relay and observe its operation during faults. The procedure involves running load flow and short circuit analyses, setting CT ratios and polarities, configuring overcurrent and differential relays, and inserting faults to test coordination and operation of the protection scheme.

    Original Description:

    Differential relay using ETAP

    Original Title

    Differential relay using ETAP

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document describes an experiment to set and test a differential relay using ETAP software. The objectives are to understand how to perform short circuit analysis in ETAP to set the relay and observe its operation during faults. The procedure involves running load flow and short circuit analyses, setting CT ratios and polarities, configuring overcurrent and differential relays, and inserting faults to test coordination and operation of the protection scheme.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    180 views2 pages

    Experiment: Setting and Testing of Differential Relay Using ETAP 1.0 Objective

    Uploaded by

    kashif
    This document describes an experiment to set and test a differential relay using ETAP software. The objectives are to understand how to perform short circuit analysis in ETAP to set the relay and observe its operation during faults. The procedure involves running load flow and short circuit analyses, setting CT ratios and polarities, configuring overcurrent and differential relays, and inserting faults to test coordination and operation of the protection scheme.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 2

    Experiment

    Setting and Testing of Differential Relay using ETAP


    1.0 Objective:
    To learn how to set and test over differential relay using ETAP.
    2.0 Learning Outcomes:
    Understanding the concept of ETAP and Short circuit analysis to set and test over
    differential relay.
    3.0 Equipment Required:
    a. ETAP Software
    4.0 Schematic Diagram:

    5.0 Experiment Procedure:


     First do the load flow analysis.
     After load flow analysis do the short circuit analysis of system.
     Now go to CT Settings and set a CT ratio of 200:5 as shown, also reverse the polarity of
    CT1.
     Open Relay setting and add CB1 at its output.
     From library select Schneider Electric manufacturer and P521 model.
     Now in OCR tab, set the overcurrent and instantaneous values of Phase.
     Now do the same setting on 2nd and 3rd CT but choose B-8 as the Designation Class. Set
    one of these CTs in reverse polarity.
     Open differential relay setting and add CB2 at its output.
     Now run Star-Protective Device Coordination analysis and put a fault anywhere on the
    system by Fault Insertion button and observe the results.
     The relay will operate the breaker immediately to protect all other equipment from being
    affected by that fault.

    6.0 Conclusion:
    ______________________________________________________________________________
    ______________________________________________________________________________
    ______________________________________________________________________________
    ______________________________________________________________________________
    ______________________________________________________________________________
    ______________________________________________________________________________
    ______________________________________________________________________________
    ___________________________________________________________________________

    You might also like